Mr. Steam MS400EE3X, MS400ED3X Specifications

368 mm

64

mm

1

30 mm

45

mm

171 mm

45 mm

1

27 mm

162 mm

48 mm

130
mm

210
mm

375
mm

302
mm

®

mr.steam

Technical Specifications

______________________________________________________
Model MS 400E

Serial Number 9000000 and higher

ater Inlet

W

Mr.Steam Standard Features

Stainless steel tank

•

• Industrial, large diameter,
serviceable heating element

• Modular Plug and Play connections

• Electronic water-levelcontrol system

• Full-port drain valve.

• Limited lifetime steam generator
parts warranty

Control & Acces­sory Connections

Steam Outlet

afety Valve

S

Manual Drain Valve

ptional

O

AutoFlush

Safety Features

• Built-in, low-voltage 24-volt control

• ASME safety valve

Locating and Installing the Steam Generator Unit

• Select a location as near as practical
to the steam room, within 60 feet.
Typical locations include: closet, van­ity cabinet, heated attic or basement

• Do not install steambath generator
inside the steam room.

• Do not install steambath generator
outdoors or wherever environmental
conditions may affect the safety and/
or performance of the generator

• Do not install steambath generator or
plumbing lines in unheated attic or
any locations where water could
freeze

• Do not install steambath generator
near flammable or corrosive materials

• 60-minute electronic countdown
shutdown with 75-minute limiting
safety back-up

or chemicals or in areas having a high con-

centration of chlorine

• Install steambath generator on a solid
and level surface or securely mounted to
a wall using the keyhole slots provided.

• Install steambath generator in an upright
position only

• Provide a minimum of 12 inches inches
at both ends and top of the steam
generator or as required for servicing.
Alternately provide unions to facilitate
installation and disconnection of the
steam generator.

• The minimum clearance from com­bustible surfaces is zero all around.

Electrical

All electrical wiring to be installed by a qualified
licensed electrician in accordance with National
Electrical Code and local electrical code.

Power Wiring

1. Check power voltage.

2. Use minimum 90˚ C/600V rated insulated copper

conductors only, type THHN or equal sized in
accordance with National Electrical Code and local
electrical code for the Amps in Ampere Chart.

If allowed by code, NM cable may require a larger

wire size than as listed on the chart.

3. Connect suitably sized equipment grounding wire to
ground terminal provided.

4. Install a separate circuit breaker between supply and
unit. Provide a power supply disconnect within
sight of the steam generator or one that is capable
of being locked in the open position.

A M P E R E C H A R T

Required Plumbing

Steam Outlet (1/2" NPT) Safety Valve (3/4" NPT)
Drain (1/2" NPT) Steam Head (1/2" NPT)

MODEL NO. VOL. CU.M. KW 3 PH AMPS (AWG)

MS 400E 10.1 9.0 380 14 12

MAX ROOM VOLTS WIRE SIZE

415 13 12

Water Supply (3/8" NPT)

FOR ILLUSTRATIVE PURPOSES ONLY. IMPORTANT NOTE: FOR SAFE AND TROUBLE FREE INSTALLATION

visit mrsteam.com or scan the QR code before installation to download the Installation, Operation and Maintenance
Manual or refer to the manual provided with the unit.

MODEL VOLTAGE* PHASE OPTIONS PROJECT INFORMATION

MS400E

Notes:

Required Equipment: iSteam,
iTempoPlus or iTempo Control

mr.steam

43-20 34th Street, Long Island City, NY 11101 TEL: 800 76 STEAM FAX: [phone] / 9410 S. La Cienega Blvd. Inglewood CA 90301 TEL:800 72 STEAM FAX: [phone]

D=380



E=415





*

Contact Mr. Steam for other voltages

®

Sussman-Automatic Corp

3-Three Phase









Optional Equipment: iGenie, AudioWizard, ChromaSteam, HomeWizard, Recessed Light, MS
Light, MS Wallseat, AutoFlush, Drip Pan, AromaSteam, Chlorine Filter, FORM Shower Systems

®

[e-mail] www.mrsteam.com

Express
Steam

Location:

Architect:

Engineer:

Contractor:

Submitted By:

Date:

TS0041-400EX REV 8.15