Mr Beams MBN340, MBN350 User Manual
Installation Instructions
NetBright® Spotlight
MBN350 / MBN340
Thank you for purchasing the NetBright
®
Motion
Sensing Spotlight. Your spotlight was created to
allow for multiple lights to work as a group in order
to improve the conditions of your home, workplace
or anywhere you need light. This technology
contributes to a safer environment and provides
Tips:
•
Use only new alkaline D- Cell batteries with 1.5V rating.
•
•
Install batte ries with polarity in correct position.
•
Light may activate when bat teries are inserted. Simply take light into a dark room. Allow
batteries to settle, then test activation.
•
If your light will not turn o, it means that it is time to replace the batteries.
bright light anywhere.
What is included per light:
• Wireless Spotlight
• Mounting Base
• 3 Screws
• 3 Anchors
What you need to install:
• 1 Small Screwdriver
• 3 D-Cell Alkaline Batteries
Spotlight Features:
Motion/Light Sensor: Light instantly turns on when it detects
motion from up to 30 feet away. The light sensor conserves battery
life by preventing the light from activating in daylight.
Auto Shut-o: Light shuts o automatically after 20 seconds if no
motion is detected.
Fully Adjustable: Light can be rotated 360° as well as up and down.
Bright LED: 200 Lumens covers up to 400 sq ft.
Durable, Weather Resistant: Tight seals and UV resistant material
allow the light to work in all weather conditions.
Multiple Lights: Spotlights will activate simultaneously when any
spotlight within the network detects motion. They will deactivate
simultaneously if no motion is detected in the group.
Do not mix old and new batteries. If batteries are not new, it may cause the light to malfunction.
Motion &
Light Sensor
Knuckle Screw
Mounti ng Base
Thumb Screw
LED Light
Mounting Base
NOTE: Light sensor only allows Spotlight to activate in darkness. We recommend you test in a dark room or closet .
1. Remove front cover of
Spotlight by rotating counterclock wise as shown above.
Pull face out from cup to reveal
battery holder.
2. Push down on battery door tab to release. Inser t 3 D- Cell batteries
into Spotlight. Make sure when you are inserting the batteries, that the
at ends match up with the springs. Attach battery door by matching
the tabs to the rectangular holes and then push down on front until door
clicks into place. Light will turn on and stay on as long as there is motion.
3. Match arrows then turn clockwise. Make sure unit
is securel y closed with arrow pointin g past the
lock sy mbol to ensu re wea ther proof seal is tigh t.
Setting up Lights to a Network
4. Determine location for mounting
Spotlight. NOTE: For best performance,
Spotlight should be positioned so motion
sensor is on top and light is on bottom.
5. Remove mounting base by turning
thumb screw counter clockwise.
6. Pull mounting base o stem.
Battery Caution:
1) Do not mix ol d and new b atter ies
2) Do not mix Alkaline, Standar d (Carb on-Zinc) or Rech arge able (N ickel
Cadmiu m) or (Nickel Met al Hydride) bat teries
3) Do not di spose of batte ries i n re
4)Batteries shoul d be recyc led or dispos ed of as per state a nd loc al guid eline s
www.mrbeams.com
7. Drive three screws into the three
holes located on mounting base.
8. Insert spotlight stem back into
mounting base pointed in desired
direction and tighten thumb screw
in base.
9. Loosen Knuckle screw that
connects spotlight head to
mounting base and adjust
spotlight head to proper
direction as shown above.
Tighten thumb screw.
After inser ting the batteries, choose a group or
channel for your spotlights with the dipswitches
next to the battery compartment. Ensure all
units are on the same channel by matching
dipswitches.
* Spotlights set to the same group that are
within 150 ft range of each other will work
together automatically
* Visit our website to view installation video.
* 1 year limited warranty. Visit site for details.
600 Beta Drive , Unit 100, M aye ld Vill age, OH 4 4143
c Wirel ess Env ironme nt 2014
877.298.9082
Loading...