Installation Instructions
Wireless Motion Sensor LED Mini Spotlight
MB300/310
Thank you for purchasing the Mr. BeamsTM |
Tips: |
|
|
Wireless Mini Spotlight. We are committed to |
• For best results, use type Alkaline C-Cell batteries with 1.5V rating |
|
|
eliminating darkness using the latest in |
• Install only new batteries of the same type in your product |
|
|
Light-Emitting Diodes (LEDs). LEDs are the most |
• Failure to insert batteries in the correct polarity, as indicated in the battery compartment, may short- |
||
efficient and durable light sources available. We |
en the life of the batteries or cause batteries to leak |
|
|
• Do not mix old and new batteries |
|
||
are certain that your light will contribute to a safer |
• Do not mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Nickel Cadmium) or (Nickel |
||
environment and provide light where you need it at |
Metal Hydride) batteries |
|
|
a very reasonable cost. |
• Do not dispose of batteries in fire |
|
|
• Batteries should be recycled or disposed of as per state and local guidelines |
|||
What is included per light: |
• Light may activate when batteries are first inserted. Simply take light into dark room |
||
• 1 Wireless Spotlight |
Allow batteries to settle, then test activation |
|
|
• 1 Mounting Bracket |
|
|
|
• 2 Screws |
|
|
|
• 2 Anchors |
|
Mounting |
|
What you need to install per light: |
|
|
|
|
Bracket |
|
|
• 1 Small Screwdriver |
|
Post |
|
• 3 C-Cell Alkaline Batteries |
|
Mounting Bracket |
|
Spotlight Features: |
|
|
Thumb Screw |
|
|
|
|
Motion/Light Sensor: Light instantly turns on when it detects |
|
|
|
motion from up to 25 feet away. The light sensor conserves battery |
Motion & |
|
|
life by preventing the light from activating in daylight. |
|
Light Sensor |
|
Auto Shut-off: Light shuts off automatically after 30 seconds if no |
|
|
|
motion is detected. |
|
|
|
Adjustable: Bracket allows light to angle up or down. |
|
|
|
Bright LED: 80 lumens covers up to 350 sq ft. |
|
LED Light |
|
Durable, Weather Resistant: Tight seals and UV resistant material |
|
allow the light to work in all weather conditions.
NOTE: Light sensor only allows Spotlight to activate in darkness. We recommend you test in a dark room or closet.
Set Up
|
|
Unlocked |
1. Unscrew thumbscrew on mounting bracket |
Locked |
3. Push bracket down toward light |
2. Tilt bracket back slightly. |
||
by turning counter-clockwise and set aside. |
|
to unlock from keyhole. |
Install/Change Batteries
4. Gently pull up on post side of bracket and lift off of light.
5. Remove front cover of spotlight by unscrewing count- er-clockwise. Pull face from cup to reveal battery holder.
6. Push down on battery door tab to release. Insert
3 C-Cell batteries, with flat side to spring. Attach battery door by inserting tabs into the rectangular holes then push down on front until door clicks into place.
7. Screw face of spotlight back into the cup by turning clockwise 3 full rotations until tightly closed.
Mounting Spotlight
8. Determine mounting location and drive two screws directly through two holes
in mounting bracket.
9.First, slide the post into bracket, then slide down to locked position.
10.Align opposite end with screw to the hole.
*Visit our website to view installation video.
*1 year limited warranty. See enclosed card for details.
11. Choose preferred angle of light, then tighten thumbscrew to lock in position.
|
|
32333 Aurora Rd. Suite 100 Solon, OH 44139 |
|
|
877.298.9082 |
www.mrbeams.com |