Mr Beams MB990 User Manual
Installation Instructions
Wireless Motion Sensor LED UltraBright Ceiling Light
MB990
What is included per light:
• Wireless LED Ceiling Light
• 4 Screws & 4 Anchors
• Mounting Bracket
What you need to install:
• 4 D-Cell Alkaline Batteries
Tips:
•
Use only new alkaline D-Cell batteries with 1.5V rating.
•
Do not mix old and new batteries. If batte ries are not new, it may cause the light to malfunction.
•
Install batte ries with polarity in correct position.
•
Light may activate when batteries are inser ted. Simply take light into a dark room. Allow
batteries to settle, then test activation.
•
If your light will not turn o, it means that it is time to replace the batteries.
• Screwdriver or Drill
Ceiling Light Features:
Motion/Light Sensor: The Ceiling Light instantly turns on
when it detects motion from up to 18 feet away. The light
sensor conserves battery life by preventing the light from
activating in daylight.
* Light sensor can be disabled - see instructions below.
Auto Shut-o: Light shuts o automatically after 30
seconds if no motion is detected.
Bright LED: 300 Lumens covers up to 300 sq ft.
Durable, Weather Resistant: Tight seals and UV resistant
material allow the Mr. Beams Ceiling Light to work in all
weather conditions.
NOTE: Light sensor only allows light to activate in darkness. We recommend you test in a dark room or closet.
Motion & L ight
Sensor
LED Light
1. To remove the back plate o the
light, press hand against the plate and
twist counter clockwise. Once loose,
lift the plate o the light.
5. To replace back plate, line up the tab with the alignment
notch. Once in place, hook one nger onto one of the tabs
and twist clockwise until tight. Make sure the tab is at the
end of the alignment notch to ensure the weatherproof seal
is engaged. Then replace the screw to hold plate into place.
2. Use a screwdriver to
remove the screw at taching
the back plate. Twist the
screw counter clockwise to
loosen.
Light sensor removal instructions
These i nstru ction s are for c ustome rs who nd there i s ambi ent lig ht in the d esire d locat ion tha t prevents their l ight from acti vating.
Once the sensor is removed, your light will activate, regardless of surrounding lights. Battery lif e will de crease once the
senso r is removed, bec ause li ght wil l activate more of ten.
10. Line up the light with the
mounting plate and twist the light
clock wise until it locks into place.
3. Use one hand to stablize the light and
use the other to twist the batter y plate o
the light. Hook a nger onto one of the tabs
on the plate and twist counter clockwise
until loose. Then lift the plate o the light.
8. Before mounting your light, test the motion
sensor in a dark closet or bathroom. Close
the light in the dark room and leave for up to 5
minutes. When you re-enter the room, the light
should activate with motion.
4. Inser t brand new batteries into the
battery compartment. Make sure the at
ends are against the springs.
9. Determine mouting location for the light. Line
up the mounting plate with ceiling and mark the
pilot holes with a pencil. Screw anchor s into the
pilot holes and line up the plate so the at side is
touching the ceiling. Then drive the screws into
the ceiling.
Locate the black rectangular piece in
the light. Remove the black rectangular
piece with needle nose plier s by lifting
up. Once the piece is removed, the
light sensor will not work until piece is
replaced. Tape the piece to the back
of the light to ensu re you don’t lose it
for future use.
Battery Caution:
1) Do not mix ol d and new b atteries
2) Do not mix Alkal ine, St andar d (Carb on-Zin c) or Rec hargeable ( Nickel Cadmiu m)
or (Nic kel Metal Hydri de) bat terie s
3) Do not di spos e of batteries in re
4) Batte ries s hould b e recycled or di spos ed of as pe r state a nd loc al guid eline s
www.mrbeams.com
* Visit our website to view installation video.
* 1 year limited warranty. Visit site for details.
32333 Au rora Rd. Suite, 10 0 Solon , OH 44139
877.298.9082
Loading...