Mr Beams MB980 User Manual

UNLOCK

LOCK

Installation Instructions

UNLOCK

LOCK

Wireless Motion Sensor LED Ceiling Light

MB980

Thank you for purchasing the Mr Beams

®

Ceiling Light. We are committed to eliminating
darkness using the latest in Light-Emitting Diodes
(LEDs). LEDs are the most ecient and durable
light sources available. We are certain that your

light will contribute to a safer environment and
provide light where you need it at a very
reasonable cost.

What is included per light:

• Wireless LED Ceiling Light

• 2 Screws & 2 Anchors

• Mounting Bracket

What you need to install:

• 4 C-Cell Alkaline Batteries

• Screwdriver

Ceiling Light Features:

Motion/Light Sensor: The Ceiling Light instantly turns on
when it detects motion from up to 20 feet away. The light
sensor conserves battery life by preventing the light from
activating in daylight.
* Light sensor can be disabled - see instructions below.

Auto Shut-off: Light shuts o automatically af ter 30
seconds if no motion is detected.

Bright LED: 100 Lumens covers up to 260 sq f t.
Durable, Weather Resistant: Tight seals and UV resistant

material allow the Mr. Beams Ceiling Light to work in all
weather conditions.

Tips:

•

Use only new alkaline C- Cell batteries with 1.5V rating.

•

Do not mix old and new batteries. If batte ries are not new, it may cause the light to malfunction.

•

Install batte ries with polarity in correct position.

•

Light may activate when batteries are inser ted. Simply take light into a dark room. Allow

batteries to settle, then test activation.

•

If your light will not turn o, it means that it is time to replace the batteries.

Motion & L ight

Sensor

LED Light

NOTE: Light sensor only allows light to activate in darkness. We recommend you test in a dark room or closet.

UNLOCK

LOCK

1. Remove mounting bracket from back of
Ceiling Light. Remove back plate of Ceiling
Light by removing thumb screw.

2. Inser t 4 fresh C batte ries.

3. To close, align tab with notch. Rotate
back plate clockwise. Inser t thumb screw
and tighten.

Light sensor removal instructions

These i nstru ction s are for c ustome rs who  nd there i s ambi ent lig ht in the d esire d locat ion tha t
prevents their l ight from acti vating. Once the sensor is removed, your light will activate,
regardless of surrounding lights. Batter y life wi ll decr ease once the sensor i s remove d, beca use
light will acti vate more often.

4. Determine the mounting

location for the Ceiling Light.
If mounting to a wall, position
so word “TOP” is at highest
point. The side with the
word “TOP” should always

face you. D rive two screws
(included) through holes of

mounting bracket to secure.

Battery Caution:

1) Do not mix ol d and new b atteries

2) Do not mix Alkal ine, St andar d (Carb on-Zin c) or Rec hargeable ( Nickel Cadmiu m)
or (Nic kel Metal Hydri de) bat terie s

3) Do not di spos e of batteries in re

4) Batte ries s hould b e recycled or di spos ed of as pe r state a nd loc al guid eline s

5. Position motion sensor lens towards
the area of expected motion. Align tabs
with grooves and t wist Ceiling Light
clock wise until it stops. Make sure light
is secure.

1. Remove mounting
bracket from back of
Ceiling Light. Remove
back plate of the
light by removing the
thumbscrew.

2. After removing
battery compartment
plate, locate the
black rectangular
piece in the center.

* Visit our website to view installation video.

* 1 year limited warranty. Visit site for details.

3. Remove the black rectangular
piece with needle nose plier s by
lifting up. Once piece is removed,
light sensor will not work until
piece is replaced. Tape the piece
to the back of the light to ensure
you don’t lose it for future use.

www.mrbeams.com

32333 Au rora Rd. Suite 100 S olon, O H 44139

877.298.9082