Mr Beams MB572 User Manual

Installation Instructions

Wireless Motion Sensor LED Path Light

MB572

Thank you for purchasing the Mr Beams

®

Path Light. We are committed to eliminating

darkness using the latest in Light-Emitting Diodes
(LEDs). LEDs are the most ecient and durable

light sources available. We are certain that your
light will contribute to a safer environment and
provide light where you need it at a very
reasonable cost.

What is included per light:

• 2 Motion Sensor Path Lights

• 4 Screws & 4 Anchors

• 2 Stakes & 2 Brackets

What you need to install:

• 1 Small Screwdriver

• 3 C-Cell Alkaline Batteries

(per light)

Path Light Features:

Motion/Light Sensor: The Path Light instantly turns on
when it detects motion from up to 15 feet away. The light
sensor conserves battery life by preventing the light from
activating in daylight.

Auto Shut-o: Path Light shuts o automatically af ter 20
or 60 seconds (optional) if no motion is detected.

Bright LED: 35 Lumens covers up to 140 sq ft.
Durable, Weather Resistant: Tight seals and UV resistant

material allow the light to work in all weather conditions.
Glow Mode Option: Emits soft glow when darkness is

sensed for safety.

Tips:

•

Use only new alkaline C- Cell batteries with 1.5V rating.

•

Do not mix old and new batteries. If batteries are not new, it may cause the light to malfunction.

•

Install batteries with polarity in corre ct position.

•

Light may activate when bat terie s are inserted. Simply take light into a dark room. Allow

batteries to settle, then test activation.

•

If your light will not turn o, it means that it is time to replace the bat teries.

LED Light

Motion & L ight

Sensor

Stake

Bracket

NOTE: Light sensor only allows light to activate in darkness. We recommend you test in a dark room or closet.

Mounting with Stake

2. Set auto shut-o to 20 sec or 60 sec.
Setting to 20 seconds will extend battery life.

1. Remove rear cover of
Path Light by removing 2
screws on back.

Mounting on Wall

Battery Caution:

1) Do not mix ol d and new b atter ies

2) Do not mix Alkaline, Sta ndard (Carbon-Zinc) o r Rechargea ble (Ni ckel Cad mium)
or (Nic kel Meta l Hydri de) batterie s

3) Do not di spose of batte ries i n re

4)Batteries should be recyc led or di spos ed of as pe r state and loca l guide lines

3. Set “GLOW ” to on if you want it to glow in

darkness or o for no glow. Set ting to o will

extend batter y life.

1. Determine location for mounting light. Flip
rear cover upside down and use hole s for thumb
screws as template to mark two holes for anchors
and/or screws (include d). We recommend
mounting the screws parallel to the ground if

mounting on a ver tical surface. Make sure that

screws are precise distance from each other as

dened by the distance of the thumb screw holes.

Replace rear cover and thumb screws.

4. Inser t 3 C-Cell batteries

into light. Replace cover.

5. Insert stake into ground
by twisting it and pushing
it down or digging a hole.

2. If using anchor s, use 3/16” drill bit to drill
holes and insert anchors. Drive screws into an­chors so that screw head potrudes 1/8” from the
surface. If using only screws, us 1/8” drill bit to
drill holes and inser t screws so that screw head
protrudes 1/8” from the sur face.

3. Slide light down so screws are securely held
by track.

6. Insert Path Light into
mounting bracket.

7. Insert mounting
bracket into stake.

www.mrbeams.com

* Visit our website to view installation video.

* 1 year limited warranty. Visit site for details.

32333 Au rora Rd . Suite 100 S olon, OH 44139

877.298.9082