Mr Beams MB371, MB370 User Manual
Indicator
Light
Auto
Shut- o
Bright
Motion
Control
Set up
Motion &
Light Sensor
LED Light
Mounting Base
Dim
Installation Instructions
Wireless LED Spotlight with Remote
MB370/371
Spotlight features:
Fully Adjustable: Light can be rotated
360° as well as up and down
Light Coverage: up to 400 sq ft
Durable, Weather Resistant: Tight seals
and UV resistant material allow the light
to work in all weather conditions
Knuckle Screw
Thumb Screw
Remote Control: Control from up to
70 ft away
What you need to install:
• 1 Small Screwdriver
• 3 D-Cell Alkaline Batteries
What is included per light:
• 1 Remote Controlled Spotlight
• Mounting Base
• 3 Screws & 3 Anchors
• 1 Remote Control with Mounting
Bracket + 2 screws
• (1) 3V Coin Battery
1. Remove front cover
of Spotlight by rotating
counter-clockwise as
shown above. Pull face
out from cup to reveal
battery holder.
2. Push down on
battery door tab to
release. Insert 3 D-Cell
batteries into Spotlight.
Attach battery door by
matching the tabs to the
rectangular holes and
then push down on front
until door clicks into
place.
3. Match arrows then
turn clo ckwise. Make
sure unit is securely
closed with arrow
pointing at the lock
symbol to ensure
weather proof seal is
tight.
4. Determine location
for mounting Spotlight.
NOTE: For best
performance, spotlight
should be positioned so
motion sensor is on top
and light is on bot tom.
5. Remove mounting
base by turning
thumb screw counterclockwise.
Remote Set-up
1. Open the Remote Control with a small coin
and insert one at 3V bat tery (included) as
shown on the inside of the Remote Control.
Smooth side of battery should be facing up.
2. Determine
placement for bracket
for remote and attach to
wall using two screws
(included) or tape.
Using the Remote
Tips:
•
Use only new alkaline D- Cell batteries with 1.5V rating.
•
Do not mix old and new batteries. If batteries are not new, it may cause light to malfunction.
•
Install batte ries with polarity in correct position.
Battery Caution:
1) Do not mix ol d and new b atter ies
2) Do not mix Alkaline, Standar d (Carb on-Zinc) or Rech arge able (N ickel Ca dmium o r Nickel Metal Hydride) batteries
3) Do not di spose of batte ries i n re
4)Batteries shoul d be recyc led or dispos ed of as per state a nd loc al guid eline s
Patent # 8,203,445
A Turns on Remote/ Adjust Auto Shut-o
B Turns o Remote
C Increase Brightness
D Decrease Brightness
E Turn Motion Sensor On/O
3. Slide Remote
into bracket as
shown above.
6. Pull mounting base
o stem.
7. Drive three screws into
the three holes located
on mounting base.
8. Insert spotlight stem
back into mounting
base pointed in desired
direction and tighten
thumb screw in base.
9. Loosen large r thumb
screw that connects
Spotlight head to
mounting base and
adjust Spotlight head
to proper direction as
shown above. Tighten
thumb screw.
Syncing your light
1. The remote is paired to work only with
the Spotlight it is packaged with. To sync
additional spotlights to a single remote,
press the exposed black button on the
spotlight next to the battery compar tment
for 3 seconds while pressing the ON button
on the remote.
Customize Remote
Activation: Spotlight can be turned on or o with the remote control.
Activating the re mote will override the light sensor, and light can be activated
at any time. Default auto shut-o mode is set for 30 seconds.
2 Auto Shut-o Options: First, activate light with remote. Next, hold the ON
button down until light blinks. When it blinks 1x, auto shut-o is set to 1 hour.
When it blinks 2x it is set for 4 hours.
3 Brightness Modes: First, activate the light with the remote control. Next,
press the bright or dim button to adjust brightness. Brightness options are 60,
90, and 140 lumens.
Motion Sensor Activation: Spotlight will activate when motion is sensed from
up to 30 ft away. Motion sensor only activates in darkness to conserve energy.
Disable Motion: Activate light with remote. Click the motion sensor but ton
down until light blinks. When it blinks 2x the motion sensor has been disabled.
When it blinks 4x, the motion sensor has been enabled. Light will remember
your last motion setting.
* Visit our website to view installation video.
* 1 year limited warranty. Visit site for details.
32333 Au rora Rd . Suite 100 S olon, O H 44139
877.298.9082
www.mrbeams.com
Loading...