Moultrie Spreader User Manual
r ATV SpreaderInstructions fo
THANK YOU for your purchase of the ATV Spreader, a top
quality Moultrie product. Please read both sides of this sheet
before operating this unit. if you should have any questions
about this or any other Moultrie product, please contact us using
the information on the revere side.
To help us better serve you, please complete and mail the
enclosed Warranty Card.
MOUNTING BRACKET TO ATV RACK
NOTE: Oblong hole should be at top.
Using provided Nuts, Washers and
U-Bolts, connect the Mounting Bracket to
the rack of the ATV as shown.
ATV Rack
U-Bolt
Mounting
Bracket
CONNECTING THE SPREADER
When sliding Feedgate Arm through
oblong hole, align the holes on the
Mounting Bracket with the holes on
the frame of the Spreader. Slide the
two Hitch Pins through both of the
holes and secure with Cotter Pins
as shown.
Cotter Pins
Hitch Pins
Spreader Frame
ATTACHING SUPPORT STRAP
Align holes
Slide a 6’x 1” Ratcheting
Tie-Down Strap through
Metal Loop on back of ATV
frame. Place S hooks of ratchet
strap around front of ATV rack.
Adjust tension strap until firm.
Metal Loop
Ratcheting Tension
Adjustment
Tie-Down
Strap
Strap S hooks
CONNECTING POWER CABLE
c a u t i on : wea r eye pr ot ect i on
Make sure the power switch is in the OFF position. Connect the provided Power Cable to the
motor switch via the black connectors. Connect to ATV’s battery by attaching the Red Alligator
Clip to the positive terminal (+), and the Black Alligator Clip to the negative (-) terrminal.
ADDING MATERIAL AND ADJUSTING AMOUNT
Add desired material such as feed, fertilizer,
seed, etc. to hopper and attach lid. Verify that
Ratchet Strap is tight enough to hold the top of
the hopper perpendicular to the ATV rack.
The Adjustment Stop allows you to set
the amount of feed dispensed. Move
Adjustment Stop towards the front of the
ATV to dispense less material. Move the
Adjustment Stop towards the rear of the
ATV to dispense more material.
OPERATING UNIT
c a u t i on : wea r eye pr ot ect i on
Feedgate Arm
Turn the Motor Switch to the ON
position.
Adjustment Stop
Move towards
Front to
dispense Less
Mounting
Bracket
Move towards
Rear to
dispense More
To spread material, Pull the Spreader’s
Adjustment Stop
Feedgate Arm towards you to Open the
feedgate and Push arm away from you to
Close. Reposition Adjustment Stop as
appropriate.
CLEANING AND STORING UNIT
NOTE: FERTILIZER IS EXTREMELY CORROSIVE. After spreading material, completely
wash and dry ATV Spreader. A light coat of oil on all metal parts and motor will help prevent rusting and corrosion.
1: (Q) Can I leave the ATV Spreader connected to
my ATV when it is not in use? (A) Yes, however to
reduce the possibility of damage to the spreader, it is
highly recommended that the hopper is empty.
2: (Q) Should I operate my ATV differently when
the ATV Spreader is loaded?
(A) Yes, the additional weight in the rear of the ATV
will cause the front-end of the ATV to be lighter.
Care must be taken when traveling up
and down hills due to this shift in weight.
3: (Q) What is the best way to set the dispensing
amount? (A) Set the adjustment stop to the position in
which you feel will provide the best coverage. Turn on
spreader and open the Feedgate. Spread material for
about 20 feet and then walk back to verify coverage.
Reposition Adjustment Stop as appropriate.
4: (Q) Can I get replacement parts for my ATV
Spreader? (A) Yes, you may purchase the following
Moultrie replacement parts.
• Directional Shroud ...... MFH-SS2
• Backplate ..................... MFH-P81686
• Bolt Pack ..................... MFH-P81539
• Motor ........................... MFH-P81747
• Wire Harness .............. MFH-P81744
• Spin Plate .................... MFH-P81145
• Hitch Pins .................... MFH-P81363
Our Service Department will gladly answer any questions you have.
Call 205-664-6700 Monday _ Friday, 8:00 AM to 5:00 PM CST.
www.moultrie feeders.com
061604R 9 / MFHP53772
Loading...