Moultrie PRO Magnum User Manual
Turn drum over, measure and mark the center of the bottom.
Center the provided template on the bottom of the drum
and secure with tape. Drill three 5/16" Feeder Leg Holes.
Using a Hole Saw, drill a 2-1/4" hole in the center of the
bottom of your drum.
caution: wear eye protection
Pro Magnum will mount to the bottom of any drum or bucket
Feeder Mounting
Holes
Instructions for Pro Magnum Feeder Kit
THANK YOU for your purchase of the Pro Magnum Feeder Kit. Please read this sheet before
operating the unit. If you should have any questions about this product or any other Moultrie
product, please contact us using the information on the back of this sheet. To help us to
better serve you and to activate your 2-year warranty, please submit your Warranty
information online at http://www.moultriefeeders.com/warranty
I
DRILLING YOUR DRUM/BARREL/BUCKET
NOTE: If you purchased a Moultrie barrel, go to step II
Pro Magnum will mount to the bottom of any drum or bucket
FeedCaster will mount to the bottom of any barrel or bucket
caution: wear eye protection
Turn drum over, measure and mark the center of the bottom.
Center the provided template on the bottom of the drum
and secure with tape. Drill three 5/16” Feeder Leg Holes.
Using a Hole Saw, drill a 2.25” hole in the center of the
bottom of your drum.
II
MOUNTING THE FEEDER
Feeder Leg Holes
From the inside of the drum, slide the three provided Bolts
through the holes on the bottom and into the provided
Flat Nuts. From the inside, using a Phillips head screwdriver,
turn the Bolt clockwise until the Flat Nut is tight against
the bottom.
Slide feeder over three Bolts that are
sticking rmly through the bottom of
the drum. Attach Feeder Kit to the Drum
using the three provided Wing-Nuts.
Bolt
Inside Drum
Outside Drum
Flat Nut
Feeder
Kit
Drum
SET
UP
DOWN
7:00
3
SET
UP
DOWN
:04
3
III
INSTALLING BATTERY
caution: wear eye protection
Remove bottom and install one or two 6-Volt
TM
Alkaline (ex. Energizer
rechargeable batteries by attaching the Red
Alligator Clip to the positive terminal (+) and
the Black Alligator Clip to the negative (-)
terminal.
) or Moultrie
IV
CONFIGURING AND TESTING FEEDER
INSTALL BATTERY: Open Control Box door and install a 6-Volt Alkaline (ex. Energizer™) or
Moultrie rechargeable battery (MFH-SRB6) by attaching the Red Alligator Clip to the positive
terminal (+) and the Black Alligator Clip to the negative (-) terminal.
SET TIME OF DAY: Press the UP or DOWN button until the correct time of day appears.
Press and release button to single-step through the minutes or hold down to advance quickly.
SET FEED TIMES: Press the SET button until the correct Timer Number appears in the
upper right hand corner as shown. Press the UP or DOWN button to set the Feed Time.
Note: Factory settings are 7am and 6pm.
SET RUN DURATION: Press the SET button again to set the RUN-TIME SECONDS
which can range from zero to twenty seconds. Adjust RUN-TIME SECONDS using
the chart below. Set the RUN-TIME SECONDS to zero to disable the specic timer.
Note: Factory setting is 4 seconds.
UP
UP
7:00
DOWN
:04
DOWN
RUN TIME (sec.)
Approx. Feed Dispensed (lbs.)1.382.623.8841.051.261.571.781.992.2102.4112.6122.8133.0143.3153.5163.7174.0184.2194.4204.6
3
SET
3
SET
SET FEED LEVEL: Your Feeder Timer is equipped with a Feed Level Estimator. Press the SET button
until “SET FEED” appears. Enter the amount of feed (lbs.) added to Hopper. The timer will automatically
UP
185
DOWN
SET
estimate the amount of feed remaining in lbs. and days after auto-scroll begins.
Note: The above estimates are based on using deer corn. Feed type, size and density
will aect calculations.
TEST FEEDER: PRESS AND HOLD the SET button while the RUN-TIME SECONDS are displayed.
Release the button and get away from the feeder when the message “TESTING GET AWAY”
appears on the display.
Helpful Tips:
– For extended battery life, the Moultrie Deluxe Solar Panel (MFH-DSP) or Feeder PowerPanel (MFA-12602) can be added using the External Power Port.
– For added security against pests, the Moultrie Varmint Guard (MFH-VG) can be added.
– Replacement parts can be purchased from Moultrie’s customer service line at the number below.
– Your feeder has a 2-year warranty against manufacturing defects from point of purchase. Visit www.moultriefeeders.com/warranty for more information.
NOTE: This equipment has been tested and found to comply with the limits of Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
Our Service Department will gladly answer any questions you have. Call 800-653-3334, Monday - Friday,
8:00 AM to 5:00 PM CST.
www.moultriefeeders.com
02202014 / MFH-PMDK
Loading...