Motorola XTNI Non-display Model User Manual

CONTENTS

CONTENTS

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Computer Software Copyrights . . . . . . . 4

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Product Safety and RF

Exposure Compliance . . . . . . . . . . . . . . . . 5

Batteries and Chargers Safety Information6

Operational Safety Guidelines . . . . . . . . . . 7

Radio Overview . . . . . . . . . . . . . . . . . . . . 8

Parts of the radio . . . . . . . . . . . . . . . . . . . . 8

ON/OFF/Volume Knob . . . . . . . . . . . . . 9

Channel Selector Knob . . . . . . . . . . . . . 9

Microphone . . . . . . . . . . . . . . . . . . . . . . 9

Antenna. . . . . . . . . . . . . . . . . . . . . . . . . 9

LED Indicator . . . . . . . . . . . . . . . . . . . . 9

Side Buttons . . . . . . . . . . . . . . . . . . . . . 9

About the Li-Ion Battery . . . . . . . . . . . . 11

Battery Recycling and Disposal . . . . . .12

Installing the Lithium-Ion (Li-Ion) Battery .

. . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . 13

Removing the Lithium-Ion (Li-Ion) Battery. .

. . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . 13

Alkaline battery pack (optional accessory) .

. . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . 14

Installing Alkaline Battery Pack . . . . . .14

Removing Alkaline Batteries. . . . . . . . . 14

Power Supply, Adaptors and Drop-in Tray

Charger. . . . . . . . . . . . . . . . . . . . . . . . .15

Installing Spring Action Belt Clip. . . . . .16

Battery Life Information . . . . . . . . . . . .16

Charging the Battery. . . . . . . . . . . . . . .17

Charging with the Drop-in Tray Single Unit

Charger. . . . . . . . . . . . . . . . . . . . . . . . .17

Charging a Stand-alone Battery . . . . . .18

Charging a Standard Battery . . . . . . . . 18

Identifying the Drop-In Charger’s Position

CONTENTS

Charging a Radio and Battery Using a Multi­Unit Charger-MUC (Optional Accessory)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Getting Started . . . . . . . . . . . . . . . . . . . . 24

Turning radio ON/OFF . . . . . . . . . . . . . . . 24

Adjusting volume . . . . . . . . . . . . . . . . . . . 24

Selecting a Channel . . . . . . . . . . . . . . . . . 24

Talking and Monitoring. . . . . . . . . . . . . . . 24

Receiving a Call . . . . . . . . . . . . . . . . . . . . 25

Talk Range. . . . . . . . . . . . . . . . . . . . . . . . 25

Radio LED Indicators . . . . . . . . . . . . . . . 27

Hands-Free Use/VOX . . . . . . . . . . . . . . . 29

With Compatible VOX Accessories. . . 29
Hands Free without Accessories (iVOX)30

Setting VOX Sensitivity . . . . . . . . . . . . 30

Microphone Gain. . . . . . . . . . . . . . . . . 30

Battery Save . . . . . . . . . . . . . . . . . . . . 30

Reset To Factory Defaults . . . . . . . . . 31

Learning To Read The Values The Radio

Signals You . . . . . . . . . . . . . . . . . . . . .32

Reading Frequencies Values . . . . . . . .35

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Reading CTCSS/DPL Values . . . . . . . . 36

Reading Auto-Scan Values . . . . . . . . .37

Programming Frequencies, Codes and

Auto-Scan. . . . . . . . . . . . . . . . . . . . . . .37

Saving Settings. . . . . . . . . . . . . . . . . . .37

Programming Mode FAQ . . . . . . . . . . .38

Programming values example . . . . . . . . . .39

Example of Programming a Frequency 39

Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Editing Scan List. . . . . . . . . . . . . . . . . .42

Nuisance Channel Delete. . . . . . . . . . .42

CPS (Computer Programming Software) .43

Bandwidth Select . . . . . . . . . . . . . . . . .44

CONTENTS

When ordering the MUC . . . . . . . . . . . 46

What to do if cloning fails . . . . . . . . . . 48

Cloning using the CPS (Computer

Programming Software) . . . . . . . . . . . 48

Troubleshooting. . . . . . . . . . . . . . . . . . . 49

Use and Care . . . . . . . . . . . . . . . . . . . . . 52

Frequency and Code Charts . . . . . . . . . 53

Motorola Limited Warranty For The United

States and Canada . . . . . . . . . . . . . . . . . 57

What Does this Warranty Cover?. . . . . . . 57

Products and Accessories. . . . . . . . . . 57

Exclusions . . . . . . . . . . . . . . . . . . . . . . 58

Exclusions . . . . . . . . . . . . . . . . . . . . . . 59

Export Law Assurances . . . . . . . . . . . . . . 60

Accessories . . . . . . . . . . . . . . . . . . . . . . 61

Audio Accessories . . . . . . . . . . . . . . . . . . 61

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

COMPUTER SOFTWARE

COPYRIGHTS

The Motorola products described in this
manual may include copyrighted Motorola
computer programs stored in semiconductor
memories or other media. Laws in the United
States and other countries preserve for
Motorola certain exclusive rights for
copyrighted computer programs, including, but
not limited to, the exclusive right to copy or
reproduce in any form the copyrighted
computer program. Accordingly, any
copyrighted Motorola computer programs
contained in the Motorola products described
in this manual may not be copied, reproduced,
modified, reverse-engineered, or distributed in
any manner without the express written

Furthermore, the purchase of Motorola
products shall not be deemed to grant either
directly or by implication, estoppel, or
otherwise, any license under the copyrights,
patents or patent applications of Motorola,
except for the normal non-exclusive license to
use that arises by operation of law in the sale
of a product.

COMPUTER SOFTWARE
COPYRIGHTS

SAFETY

SAFETY

PRODUCT SAFETY AND RF
EXPOSURE COMPLIANCE

ATTENTION!

This radio is restricted to occupational use
only to satisfy FCC RF energy exposure
requirements.

For a list of Motorola-approved antennas,
batteries, and other accessories, visit the
following website which lists approved
accessories:

http://www.motorola.com/XTNi

Before using this product, read
the operating instructions and RF
energy awareness information
contained in the Product Safety
and RF Exposure booklet
enclosed with your radio.

!

C

a u t i o

n

BATTERIES AND CHARGERS

SAFETY INFORMATION

BATTERIES AND CHARGERS
SAFETY INFORMATION

This document contains important safety and
operating instructions. Read these instructions
carefully and save them for future reference.

Before using the battery charger, read all the
instructions and cautionary markings on

• the charger,

• the battery, and

• the radio using the battery.

1. To reduce risk of injury, charge only the

rechargeable Motorola-authorized batteries.

Other batteries may explode, causing personal

injury and damage.

2. Use of accessories not recommended by

Motorola may result in risk of fire, electric

3. To reduce risk of damage to the electric plug

and cord, pull by the plug rather than the cord

when disconnecting the charger.

4. An extension cord should not be used unless

absolutely necessary. Use of an improper

extension cord could result in risk of fire and

electric shock. If an extension cord must be

used, make sure that the cord size is 18AWG

for lengths up to 100 feet (30.48 m), and

16AWG for lengths up to 150 feet (45.72 m).

5. To reduce risk of fire, electric shock, or injury,

do not operate the charger if it has been broken

or damaged in any way. Take it to a qualified

Motorola service representative.

6. Do not disassemble the charger; it is not

repairable and replacement parts are not

available. Disassembly of the charger may

result in risk of electrical shock or fire.

BATTERIES AND CHARGERS

SAFETY INFORMATION

OPERATIONAL SAFETY GUIDELINES

• Turn the radio OFF when charging battery.

• The charger is not suitable for outdoor use. Use

only in dry locations/conditions.

• Connect charger only to an appropriately fused

and wired supply of the correct voltage (as

specified on the product).

• Disconnect charger from line voltage by

removing main plug.

• The outlet to which this equipment is connected

should be nearby and easily accessible.

• In equipment using fuses, replacements must

comply with the type and rating specified in the

equipment instructions.

• Maximum ambient temperature around the

power supply equipment must not exceed 40°C

(104°F).

• Power output from the power supply unit must

not exceed the ratings stated on the product

label located at the bottom of the charger.

• Make sure the cord is located where it will not be

stepped on, tripped over, or subjected to water,

damage, or stress.

RADIO OVERVIEW

Antenna

Microphone

Channel
Selector Knob

ON/
OFF/
Volume

LED
Indicator

Model Label

PTT (Push-to­Tal k ) B ut t on

SB1 - Monitor
Button

SB2 - Scan/
Nuisance

PARTS OF THE RADIO

RADIO OVERVIEW

ON/OFF/Volume Knob

Used to turn the radio ON or OFF and to adjust
the radio’s volume.

Channel Selector Knob

Used to switch the radio to different channels.

Microphone

Speaks clearly into the microphone when
sending a message.

Antenna

The radio's antenna is non-removable.

LED Indicator

Used to give battery status, power-up status,
radio call information and scan status

Side Buttons

• Side Button 1 (SB1)

The Side Button 1 is a general button that can
be configured by the Computer Programming
Software - CPS. The default setting of SB1
button is ‘Monitor’.

• Side Button 2 (SB2)

The Side Button 2 is a general button that can
be configured by the CPS. The SB2 default
setting is ‘Scan/Nuisance Channel Delete’.

The Lithium-Ion (Li-Ion) Battery

XTNi™ Series provides different types of
batteries. For more information, see ‘

Battery

Features and Charging Options’ on page 11.

This User Guide covers multiple XTNi™ Series
models, and may detail some features your
radio does not have. The model number of the
radio is shown on the front of the radio,

underneath the speaker, and tells you the
following information:

Model

Frequency

Band

Transmit Power

(Watts)

Number of

Channels

Antenna

XTNi PMR446 0.5 8 Non-removable

BATTERIES AND

CHARGERS

BATTERIES AND CHARGERS

XTNi™ Series radios provide Lithium-Ion (Li­Ion) batteries that comes in different capacities
that will define the battery life. It also offers the
option to use Alkaline batteries.The radio
comes equipped with a rapid charger.

BATTERY FEATURES AND CHARGING
OPTIONS

About the Li-Ion Battery

The XTNi™ radio series come equipped with a
rechargeable Li-Ion battery. This battery
should be charged before initial use to ensure
optimum capacity and performance.

Battery life is determined by several factors.
Among the more critical are the regular
overcharge of batteries and the average depth
of discharge with each cycle. Typically, the

times a day, lasts fewer cycles than a battery
that receives less of an overcharge and is
discharged to 50% per day. Further, a battery
which receives minimal overcharging and
averages only 25% discharge, lasts even
longer.

Motorola batteries are designed specifically to
be used with a Motorola charger and vice
versa. Charging in non-Motorola equipment
may lead to battery damage and void the
battery warranty. The battery should be at
about 77°F (25°C) (room temperature),
whenever possible. Charging a cold battery
(below 50° F [10°C]) may result in leakage of
electrolyte and ultimately in failure of the
battery. Charging a hot battery (above 95°F
[35°C]) results in reduced discharge capacity,
affecting the performance of the radio.
Motorola rapid-rate battery chargers contain a

BATTERIES AND

CHARGERS

Battery Recycling and Disposal

Li-Ion rechargeable batteries can be recycled.
However, recycling facilities may not be
available in all areas. Under various U.S. state
laws and the laws of several other countries,
batteries must be recycled and cannot be
disposed of in landfills or incinerators. Contact
your local waste management agency for
specific requirements and information in your
area. Motorola fully endorses and encourages
the recycling of Li-Ion batteries. In the U.S. and
Canada, Motorola participates in the
nationwide Rechargeable Battery Recycling
Corporation (RBRC) program for Li-Ion battery
collection and recycling.

Many retailers and dealers participate in this
program. For the location of the drop-off facility
closest to you, access RBRC's Internet web
site at www.rbrc.com or call 1-800-8­BATTERY. This internet site and telephone
number also provides other useful information
concerning recycling options for consumers,
businesses and governmental agencies.

BATTERIES AND

CHARGERS

Installing the Lithium-Ion (Li-Ion) Battery

1. Turn OFF the radio.

2. With the Motorola logo side up on the battery

pack, fit the tabs at the bottom of the battery into

the slots at the bottom of the radio’s body.

3. Press the top part of the battery towards the radio

Removing the Lithium-Ion (Li-Ion) Battery

1. Turn OFF the radio.

2. Push down the battery latch and hold it depressed

while removing the battery.

3. Pull the battery away from the radio.

slots

battery
latch

battery
latch

BATTERIES AND

CHARGERS

Alkaline battery pack (optional accessory)

Installing Alkaline Battery Pack

1. Turn OFF the radio, if it is turned on.

2. Remove Li-Ion battery

3. Assemble alkaline battery pack (optional

accessory) in the same steps as installing the Li-

Removing Alkaline Batteries

1. Turn OFF the radio, if it is turned on.

2. Slide the battery latches, on both sides of the

battery, downwards.

3. Pull the top of the battery away from the radio’s
body, and lift the battery from the radio’s body.

Alkaline
Battery
Door

Alkaline
Battery
Door

BATTERIES AND

CHARGERS

Power Supply, Adaptors and Drop-in Tray
Charger

Your radio comes with one Drop-in Tray
Charger, one Power Supply (also known as
Transformer) and a set of adaptors.

Your power supply, has a ‘switchable’
capability which allows to suit any of the
adaptors that comes with your radio package.
The adaptor you should choose to install

• Slide down the adaptor grooves into the power

supply until it snaps into place.

• Slide the adaptor upward to remove.

Note: The adaptor shown in the pictures are just

Drop-in Tray Charger

Power Supply

Install

Remove

Adapto

r

Power SupplyPower Supply

Adaptor

BATTERIES AND

CHARGERS

Installing Spring Action Belt Clip

1. Slide the spring action belt clip rails into the belt

clip grooves on the back of the battery pack

and slide it down until the belt clip tab snaps

into place.

2. To remove, pull back the metal release tab on the

Battery Life Information

Li-Ion Battery Life

Depending on the radio model and/or region
the battery capacity will be different. This
feature will determine the estimated battery
life. When the Battery Save feature is ON
(enabled by default) the battery life will be
longer. The following chart summarizes battery
life estimations:

belt clip tab

spring
action belt
clip

Li-Ion Battery Life with Battery Save

feature ON

Battery 0.5 Watt

Standard 16 hours

High Capacity 32 hours

Note: Battery life is estimated based

BATTERIES AND

CHARGERS

Alkaline Battery Life

The following chart provides estimations about
the Battery Life using the Alkaline Batteries:

Charging the Battery

To charge the battery (with the radio attached),
place it in a Motorola-approved Drop-in Tray
Single Unit Charger or Drop-in Tray Multi-Unit
Charger.

Charging with the Drop-in Tray Single Unit
Charger

Alkaline Battery Life

Battery Save Feature 0.5 Watt

ON 37 hours

Note: Battery life are being estimated

based on 5% transmit/ 5%

receive/ 90% standby standard

duty cycle.

Power Supply
(Transformer)

Drop-in Tray Charger

Drop-in Tray
Charger Port

BATTERIES AND

CHARGERS

radio facing the front of the charger, as shown.

Note: When charging a battery attached to a radio,

turn the radio OFF to ensure a full charge.

See ‘

Operational Safety Guidelines’ on

page 7 for more information.

Charging a Stand-alone Battery

To charge a battery whilst not attached to the
radio - at step 4 above, insert the battery into

Important: Ensure that the bracket in the charger is

adjusted to the correct position for

either Standard or High-capacity

battery. See ‘Charging a Standard

Battery’ on

page 18.

Charging a Standard Battery

The drop-in tray charger has a removable
bracket that is adjustable depending on the
type of battery that needs to be charged. It is
designed to charge either the battery (with the
radio) or a standalone battery. The drop-in tray
charger comes by default set up to charge a
standard battery. The following image on page
page 19 shows the orientation for each battery:

BATTERIES AND

CHARGERS

Identifying the Drop-In Charger’s Position
Before Charging Battery

A

djustable bracket

Standard

High and Ultra High Capacity

Adjustable bracket

BATTERIES AND

CHARGERS

Charging a High Capacity Battery

To convert the charger from the default

setup to accommodate the high capacity:

1. Squeeze both tabs on each side of the

removable bracket in the drop-in charger tray

carefully and lift the bracket from the charger

tray.

3. Repeat same procedure to return position back to

charging a Standard Battery. Label on the

removable bracket should show ‘Standard

Battery’ facing front.

Note: Make sure the bracket is assembled

correctly for both standalone battery and

battery (with radio) to be properly charged.

Removable

Piece

Removable

Piece

Turn around

horizontal

180 degree

BATTERIES AND

CHARGERS

Drop-in Tray Charger LED Indicators

Standard Charger LED Indicator

Status LED Status Comments

Power ON

Steady red indication for 3
seconds

The charger has powered up

Charging Blinking red (slow) The charger is currently charging

Charging
Complete

Steady red indication Battery is fully charged

Battery Fault(*) Blinking red (fast) Battery had a fault when battery was inserted

Notes:

• (*) Normally re-seating the battery pack will correct this issue.

• (**) Battery temperature is too warm or too cold or wrong power supply is being used

Rapid Charger LED Indicator

Status LED Status Comments

Power ON Steady green indication for 3 seconds The charger has powered up

Charging Blinking green The charger is currently charging

Top-off Charging Blinking green (slow) Battery is near fully charged

Charge
Complete

Steady green indication Battery is fully charged

BATTERIES AND

CHARGERS

Estimated Charging Time

The following table gives the estimated times
to charge the battery. For further details, see
‘

Accessories’ on page 58.

Estimated Charging Time

Charging

Solution

Battery Capacity

Standard High

Rapid Charging

Solution

1.5 hours 3 hours

BATTERIES AND

CHARGERS

Charging a Radio and Battery Using a Multi­Unit Charger-MUC (Optional Accessory)

The Multi-Unit Charger (MUC) allows drop-in
charging of up to 6 radios or batteries.
Batteries can be charged with the radios or
removed and placed in the MUC separately.
Each of the 6 charging pockets can hold a
radio or battery, but not both.

1. Place the charger on a flat surface.

2. Insert the power cord plug into the jack on the

6. Insert the radio or battery into the charging

pocket.

Notes:

• This Multi-Unit Charger will also allow you to clone

up to 3 radios (3 Source radios and 3 Target

radios).

• When cloning, the MUC does not need to be

plugged into a power source, but all radios require

charged batteries. Further details on MUC’s

operation are explained in the Instructions Sheet

provided with the MUC. Refer to the “Accessories”

section to identify the part number for ordering the

MUC.

MUC LED Indicator

Status LED Status Comments

Charging

Steady Red

Indication

The charger is

currently charging

Charge

Complete

Steady Green

Indication

Battery is fully

charged

GETTING STARTED

English

GETTING STARTED

For the following explanations, refer to page 8
of the user guide.

TURNING RADIO ON/OFF

To turn ON the radio, rotate the ON/OFF/
Volume Knob clockwise. The radio will chirp
and the LED will briefly blink red.

To turn the radio OFF, rotate the ON/OFF/
Volume Knob counterclockwise until you hear
a ‘click’ and the radio LED indicator turns OFF.

ADJUSTING VOLUME

Turn the ON/OFF/Volume Knob clockwise to
increase the volume, or counterclockwise to
decrease the volume.

Note: Do not hold the radio too close to the ear

when it is at a high volume setting or when

SELECTING A CHANNEL

To select a channel, rotate the Channel
Selector Knob and select the desired channel
number.

Program each channel separately. Each
channel has its own Frequency, Interference
Eliminator Code and Scan Settings.

TALKING AND MONITORING

It is important to monitor for traffic before
transmitting to avoid ‘talking over’ someone
who is already transmitting

To monitor, press and hold the SB1(*) button
for 2 to 3 seconds to access channel traffic. If
no activity is present, you will hear ‘static’. To
release, press SB1 again. Once channel traffic
has cleared, proceed with your call by pressing
the PTT button. When transmitting, the radio

GETTING STARTED

RECEIVING A CALL

1. Select a channel by rotating the Channel

Selector Knob until you reach the desired
channel.

2. Make sure the PTT button is released and
listen for voice activity.

3. The LED indicator blinks RED while the
radio is receiving a call.

4. To respond, hold the radio vertically 1 to 2
inches (2.5 to 5cm) from mouth. Press the
PTT button to talk; release it to listen.

Note: Please notice that when radio is receiving or

transmitting, LED is always RED.

Note: In order to listen to all activity on a current

channel, short press the SB1 to set the

CTCSS/DPL code to 0. This feature is called

TALK RANGE

XTNi radios have been designed to maximize
performance and improve transmission range
in the field. It is recommended that you do not
use the radios closer than 1.5 meters apart, to
avoid interference.

Talk range depends on the terrain. It will be
affected by concrete structures, heavy foliage
and by operating radios indoors or in

vehicles.

Optimal range occurs in flat, open areas with
up to 9 kilometres of coverage. Medium range
occurs when buildings and trees are in the

way. Minimal range occurs when dense foliage
and mountains obstruct the communication
path.

To establish a proper two-way communication,
the channel, frequency, and interference

GETTING STARTED

English

1. Channel: Current channel that the radio is

using, depending upon radio model.

2. Frequency: The frequency the radio uses
to transmit/receive.

3. Interference Eliminator Code: These
codes help minimize interference by
providing a choice of code combinations.

4. Scramble Code: Codes that make the
transmissions sound garbled to anyone
listening who is not set to that specific
code.

5. Bandwidth: Some frequencies have
selectable channel spacing, which must
match other radios for optimum audio
quality.

For details of how to set up frequencies and
CTCSS/DPL codes in the channels, refer to
“Programming Mode” on page 31.

Note: Interference Eliminator Codes are referred

also as CTCSS/DPL codes or PL/DPL codes

GETTING STARTED

RADIO LED INDICATORS

RADIO STATUS LED INDICATION

Channel Alias Edit Red heartbeat

Channel Busy

Solid orange

Cloning Mode

Two orange heartbeats

Cloning In Progress

Solid orange

Fatal Error at Power up

One green blink, one orange blink, one green blink, then repeat for
4 seconds

Low Battery

Orange blink

Low Battery Shutdown

Orange heartbeat

Monitor

LED is OFF

Power-Up

Solid red for 2 seconds

‘Idle’ Programming Mode /
Channel Mode

Green heartbeat

Scan Mode

Red heartbeat)

GETTING STARTED

English

HANDS-FREE USE/VOX

Motorola XTNi™ radios can operate hands­free (VOX) when used with compatible VOX
accessories. A short delay occurs between
talking and the radio transmission.

usethe CPS (Computer Programming
Software) to make sure the VOX level is set to
a level different from "0". Then, perform the
following steps:

1. Turn radio OFF.

2. Open accessory cover.

3. Insert plug of audio accessory firmly into

accessory port.

4. Turn radio ON. Radio LED will blink double red

5. Lower radio volume BEFORE placing

accessory near ear.

6. To transmit, speak into accessory microphone

and to receive, stop talking.

7. VOX can be temporarily disabled by pressing

the PTT button or by removing the audio

accessory.

Note: To order accessories, contact your Motorola

GETTING STARTED

Hands Free without Accessories (iVOX)

• Enable iVOX by pressing the PTT button

while turning the radio ON.

• iVOX operation can be temporarily disabled

by pressing PTT.

• A short press of the PTT button will re-

enable iVOX.

There is a short delay between when talking
and the radio transmission.

Note: The iVOX feature is only available on XTNId

(Display model).

Setting VOX Sensitivity

The sensitivity of the radio's accessory or
microphone can be adjusted during VOX
operation to suit different operating

Default value is OFF (level 0). If you want
touse the VOX feature, VOX level should be
set at a level different from 0.

1 = Low sensitivity

2 = Medium sensitivity

3 = High sensitivity

Microphone Gain

The sensitivity of the radio's microphone can
be adjusted to fit different users or operating
environments.

This feature can be adjusted only through the
CPS. Microphone default setting is set to level
2 (Medium gain).

Battery Save

GETTING STARTED

English

seconds while powering up the radio until you
hear a quick series of beeps. To have a slightly
better attack time, set Battery Save feature to
OFF so that the radio is always ready to
transmit or receive without any delays.

Note: Battery Save feature is set to ON by default

Reset To Factory Defaults

Reset To Factory Defaults will set back all
radio features to the original factory default
settings. To do so press PTT, SB2 and SB1
simultaneously while turning ON the radio until
you hear a high tone chirp beep.

End of Transmission Tone (Roger Beep
Tone)

Short press the SB1 button while turning ON
the radio to enable/disable End of
Transmission Tone.

PROGRAMMING

FEATURES

PROGRAMMING FEATURES

To easily program all the features in your radio,
it is recommended to use the CPS Kit which
includes the Programming Cable, CPS and
accessories sections.

Programming Mode

Programming Mode is special radio mode that
allows you to program basic radio's features by
using the radio’s panel programming.

When the radio is set to Programming Mode,
you are able to read and modify three features:

• Frequencies,

• Codes (CTCSS/DPL) and,

• Auto-scan.

The Programming Frequencies feature allows
you to select frequencies for each channel.

filter out static, noise, and unwanted
messages.

The Auto Scan feature allows you to set a
particular channel to automatically enable scan
each time you switch to that channel ( you will
not need to press any button to start scanning).

Learning To Read The Values The Radio
Signals You

As the non-display model does not have a
display to show the values that are being
programmed, the radio will communicate this
information using beeps and LED indications.
The radio's LEDs will blink two colors: 'orange'
to signal '0' and red for other values from '1' to
'9'. Short and long red blinks differentiate the
specific number the radio is showing you.

English

Table 1: Programming Mode: Reading your Radio's Features Values

Number Confirmation Beep LED Indication

0 Zero beep One short orange blink
1 One beep One short red blink
2 Two beeps Two short red blinks
3 Three beeps Three short red blinks
4 Four beeps Four short red blinks
5 Long beep One long red blink
6 Long beep and one beep One long and one short red blinks
7 Long beep and two beeps One long and two short red blinks
8 Long beep and three beeps One long and three short red blinks
9 Long beep and four beeps One long and four short red blinks

PROGRAMMING

FEATURES

PROGRAMMING MODE

1

2

3

PTT

PTT

PTT

PTT

Long
PTT

Long
PTT

Long
PTT

Exit

“Roll Over”

key chirp

PTT

PTT

Enter Programming Mode

(PTT + SB1 + Turn ON radio)

PTT

Second

Digit

Third

Digit

ON/
OFF

Auto-Scan

CTCSS/DPL

Frequencies

Idle

Programming

Mode

First

Digit

First
Digit

Second

Digit

Figure 1 Entering Programming Mode

English

Entering Programming Mode

Note: Before programming the features, make

sure your radio is set to the channel you

wish to program. You can do so before

entering Programming Mode or at any time

during the Programming Mode by turning the

Channel Selector Knob to the desired

channel.

To read or modify frequencies, codes and
auto-scan, set the radio to 'Programming
Mode' by long pressing both the PTT and the
SB1 button simultaneously while turning ON
the radio for 3 to 5 seconds until a ‘chirp’
sounds to indicate that you have entered 'Idle'
Programming Mode (*).The radio LED will start
blinking a green heartbeat.

Note: (*)'Idle' Programming Mode is the stage of

Once you are in the 'Idle' Programming Mode,
you will be able to read the radio frequencies,
codes and auto-scan setting by short pressing
the PTT button to move along the different
programmable features.

Reading Frequencies Values

When reading frequencies values you need to
read two digits as XTNi™ series radios have
16(*) frequencies for UHF (refer to UHF
Frequencies tables).

Once in ‘Idle’ Programming Mode, the radio
will signal the first value it was programmed
when you short press the PTT button (see
picture below). This value corresponds to the
frequency's first digit value. If you short press
the PTT button again, the radio will signal you
the second digit value.

PROGRAMMING

FEATURES

Reading CTCSS/DPL Values

If you continue short pressing the PTT button,
as shown in the

”Entering Programming Mode”
on page 33 (Stage 2) the radio will move
forward to programming CTCSS/PL Codes.

When reading the values for CTCSS/PL Codes
the radio signals you the digit codes each time
you short press the PTT button. You will have
to read three digits as XTNi Series™ have up

The following is an example of the order in

which your radio will be signaling the ‘118’

CTCSS/DPL code:

:

• Short press the PTT button. The radio will
signal you the first digit ‘1’, short press PTT
button again and the radio will show the
second digit ‘1’ and finally, short press PTT
again and radio will show the third digit ‘8’.

1

PTT

PTT

Frequencies

First

Digit

Second

Digit

First
Digit

Third
Digit

Second Digit

Example of how to program values

118

English

Reading Auto-Scan Values

After finishing reading CTCSS/DPL codes, if
you short press PTT once again, the radio will
take you to Auto-Scan (”Entering Programming
Mode” on page 33 (stage 3) Auto-Scan only
has two values:

Note that while in Auto-Scan Mode, if you short

press PTT button, the radio will return to the
‘Idle’ Programming Mode. It will then generate
a ‘roll-over’ chirp and it will start blinking a
green heartbeat.

Programming Frequencies, Codes and
Auto-Scan

Each time your radio signals and beeps, you
can change the current setting value by either
increasing it by short pressing SB1 or
decreasing it by short pressing SB2. The radio
will then signal the new setting it has been
programmed to.

Saving Settings

If you are satisfied with the new setting, you
can either:

• short press PTT to continue programming,

• long press PTT to save and return to 'Idle'
Programming Mode, or

• long press the PTT button twice to exit 'Idle'
Programming Mode and return to the normal
radio operation.

If the radio signals

the value...

It means Auto-

Scan is....

0

OFF

1

ON

Note: AutoScan is set to OFF by default.

PROGRAMMING

FEATURES

Notes:

• If you don't want to save the value you just
programmed, turn radio OFF or change
channel using the channel knob.

• If you ‘roll-over’ to the beginning at Idle
Programming Mode you will hear a ‘chirp’ and
radio LED will start blinking green again. All
values that were changed will be automatically
saved.

Programming Mode FAQ

1. I got distracted while programming and
forgot which digit I was programming. What
should I do?

Return to 'Idle' Programming Mode and start
over, as you will not be able to go back into the
Programming Mode (the radio does not
provide further way to let you know the specific

• Turn OFF the radio and enter Programming
Mode again (see instructions in the beginning
of this section)

2. I am trying to program a frequency (or
code) value but the radio would not do it. It
rolled over and took me back to value ‘0’.

The radio will not allow you to program any
values that are not available in the frequencies
and codes pool. For example, if you try to
program code 128, the radio would not accept
it, as the maximum value allowed is 122. Same
thing will happen with frequencies. Check the
Frequencies and Codes Charts section to
make sure you are programming a valid
number.

3. I am trying to enter the Programming
Mode but the radio would not do it.

The radio might be locked using the CPS for

English

4. When I was programming I made a
mistake and program the wrong value. How
can I erase it or re-program it?

If you make a mistake while programming a
value you have two choices:

a) The radio roll-over (and generates a 'wrap­around' sound) each time it reaches a
maximum (9) or minimum (0) value. Keep
increasing (short press SB1) or decreasing
(short pressing SB2) until you get the desired
value or,

b) Turn OFF the radio and start-over.

5. I just programmed the value I wanted.
How do I exit Programming Mode?

• If you are in Programming Mode you can exit
by long pressing the PTT button twice.

• If you are already in the ‘Idle’ Programming

6. I am done programming the features in
this channel and want to program another
channel.

Switch to the new channel you wish to program
by using the Channel Selector Knob. The radio
will go into to the 'Idle' Programming Mode. If
you wish to save the changes, make sure you
are in the ‘Idle’ Programming Mode before
switching the channel as otherwise you will
lose changes made.

PROGRAMMING VALUES EXAMPLE

Example of Programming a Frequency

Assuming current frequency value is set up to
channel 1, with the UHF default frequency ‘02’
(equivalent to

446.01875 Mhz), and you want to

change it to Frequency Number = ‘13’ (which is
mapped to

446.05625 Mhz), follow this

PROGRAMMING

FEATURES

• Short press the PTT button to enter
Frequency Mode. Radio will signal current
value ‘0’ (orange blink)

• Press the SB1 button once to increase first
digit to ‘1’.

• Short press the PTT button once to move
ahead and program the frequency’s second
digit. Radio will signal current value which is ‘2’
(two red blinks).

• Press the SB1 button to increase the digit
value to ‘3’.

• Long press the PTT button. LED indicator will
show a green heartbeat to indicate 'Idle' state.

• Long press the PTT button to exit
Programming Mode or turn radio OFF.

Example of Programming a Code

Assuming current code value is set to factory
default ‘001’, and you want to change it to

• Short press the PTT button three times (Enter
CTCSS/DPL Programming Selection Mode).
Radio LED will blink orange to indicate that
current value is ‘0’ • Press the SB1 button once
(to change first digit to ‘1’) LED indicator will
blink red. Short press the PTT button (to move
forward and program second digit). Radio LED
will blink orange to indicate current value is ‘0’.

• Short press the PTT button and move ahead
to program the third digit. LED indicator will
blink red to indicate current value is ‘1’.

• Press the SB1 button to change the ‘third
digit’ to ‘2’. Press the SB1 button to change
again this ‘third digit’ to ‘3’. Radio will signal the
chosen value.

• Long press the PTT button to save changes
and return to 'Idle' Programming Mode.

• Once in 'Idle' Programming Mode, LED

English

Example of Programming Auto Scan

Auto-Scan is the last Programming Mode and
can be set to "ON" or "OFF" on a particular
channel. To set Auto Scan to “ON”:

1. Enter Programming Mode and select the
desired channel (see "Entering Programming
Mode" picture in page 38).

2. Short press the PTT button six times to enter
Auto Scan Programming Selection Mode. The
radio will signal beeps and will show the
current
Auto Scan setting (please refer to "Reading
Auto-scan Settings" in page 41).

3. Short press the SB1 button to toggle ON/
OFF the auto-scan feature in the channel.
When ON radio LED will blink RED once.
When OFF radio LED will blink ORANGE
once.

OTHER PROGRAMMING FEATURES

SCAN

Scan allows you to monitor other channels in
order to detect conversations.
When the radio detects a transmission, it will
stop scanning and will stay on the active
channel. This will allow you to listen and talk to
the people on that stopped channel without
having to change the channel knob. If there
is talking going on channel 2 during this time,
the radio will stay on channel 1 and you will not
hear channel 2. After talking has stopped in
channel 1, the radio will wait 5 seconds before
resuming scan again.

• To start scanning, press the SB2 button (*).
When the radio detects channel activity, it will
stops on that channel until the activity ends.
You can talk to the person(s) transmitting
without having to switch channels by pressing

PROGRAMMING

FEATURES

scanning, the radio will transmit on the channel
which was selected before Scan was
activated.
If no transmission occurs within five seconds,
scanning will resume.

• If you want to scan a channel without
Interference Eliminator Codes (CTCSS/DPL),
set the code settings for the channels to ‘0’ in
the CTCSS/DPL Programming Selection
Mode.
Whenever the radio is set up in Scan, the LED
will signal a red blink.

Note: (*)Assumes the SB2 button is not

programmed to other function different from

the default. If Auto-Scan has been enabled

for a particular channel, do not press SB2 to

scan the channel, as the radio will do it

automatically.

(refer to ”CPS (Computer Programming
Software)” on page 42.

Nuisance Channel Delete

Nuisance Channel Delete allows you to
temporarily remove channels from the Scan
List. This feature is useful when irrelevant
conversations on a ‘nuisance’ channel tie up
the radio's scanning feature. To delete a
channel from the scan list:

• Start Scanning by short pressing the SB2
button(*)

• Wait until the radio stops on the channel you
wish to eliminate, then long press the SB2
button to delete it.

• The channel will not be removed until you exit
Scan by short pressing the SB2 button again
or by turning the radio OFF.

English

CPS (COMPUTER PROGRAMMING
SOFTWARE)

The easiest way to program or change
features in your radio is by using the Computer
Programming Software (CPS) and the CPS
Programming Cable(*). CPS Software is
available for free as web based downloadable
software at www.motorola.com/XTNi.

To do so, connect the XTNi radio via the Drop­in Charger Tray and CPS Programming Cable

features such as: Direct Frequency Input,
Repeater/Talkaround, Bandwidth Select, Time­out Timer, Power Select, Battery Type Select,
Scan List, Call Tones, Scramble, Reverse
Burst etc. CPS is a very useful tool as it can
also lock the frontpanel radio programming or
restrict any specific radio feature to be
changed (to avoid preset radio values to be
accidentally erased).

It also provides security by giving the option to
set up a password for profile radio's
management. Please refer to Features
Summary Chart Section at the end of the
User's Guide for more details.

Note: • Features should be enabled by an
Authorized Motorola Dealer. Contact your
Motorola Point of Purchase for details

Note: (*) CPS Programming Cable is an
accessory sold separately. For part number

Radio to be

programmed

CPS

Programming

Cable

Drop-in

Charger

Tray

Mini-connector

USB

Connector

CPS Software

PROGRAMMING

FEATURES

Bandwidth Select

Default setting for Bandwidth Select is 12.5
KHz. Some frequencies have selectable
channel spacing, which must match other
radios for optimum audio quality.

Time-Out Timer

When pressing PTT buttons, transmissions
can be terminated by setting up a Time-Out
Timer. The radio can be programmed to turn
the radio ‘OFF’ in either 60, 120 or 180
seconds.

Battery Type Setting

The XTNi™ radio can be powered by either
Alkaline or Lithium-Ion batteries.

Call Tones

Call Tones enable you to transmit to other

Scramble

The Scramble feature makes transmissions
sound garbled to anyone listening without the
same code. Scramble default value is OFF.

Note: Some of the features available with the CPS

software may vary depending on the radio

model.

Reverse Burst

Reverse Burst eliminates unwanted noise
(squelch tail) during loss of carrier detection.
Can select values 180/240.

Notes:

• The features described in previous pages are
just some of the features CPS has. CPS offers
more capabilities. For more information please
refer to the HELP file in the CPS.

English

CLONING RADIOS

You can copy XTNi™ Series radio profiles from
one Source radio to a Target radio by using
any of these 3 methods:

1. One Multi Unit Charger (optional

accessory)

2. Two single unit chargers and a Radio-to-

Radio cloning cable (optional accessory)

3. the CPS (free software download)

Cloning with a Multi-Unit Charger (MUC)

To clone radios using the MUC, there must be
at least two radios:

• a Source radio(radio to be cloned or

copied) and

• a Target radio (radio which profile will be

changed to be the same as the source
radio.)

by pairs as follows: 1 and 2 or 3 and 4 or 5 and

6.

When cloning, the MUC does not need to be
plugged into a power source, but ALL radios
require charged batteries.

Follow these steps for cloning:

1. Turn ON the Target radio and place it into one of
the MUC Target Pockets

2. Power the Source radio following the sequence
below:

- Long press the PTT button and SB2 simulta-

PROGRAMMING

FEATURES

Press and release SB1.

4. After cloning is completed, the Source radio will
sound either a ‘pass’ tone (cloning was successful)
or a ‘fail’ tone (cloning process has failed). The
‘pass’ tone sounds like a good key ‘chirp’ whereas
the ‘fail’ tone sounds similar to a ‘bonk’ tone. If the
Source radio is a display model, it will either show
‘Pass’ or ‘Fail’ on the display (a tone will be heard
within 5 seconds).

5. Once you have completed the cloning process,
turn the radios OFF and ON to exit the ‘cloning’
mode.

If cloning fails please refer to ”What to do if
cloning fails” on page 47.

Further details on how to clone units are
explained in the instructions sheet provided
with the MUC.

When ordering the MUC

See ”Chargers” on page 59 for the MUC part

Cloning Radio using the Radio to Radio
(R2R) Cloning Cable (optional accessory)

Paired Target radios and
Source Readios must be
of the same type in order
for the cloning to run
successfully.

!

W A R N I N G

!

English

Operating Instructions

1. Before beginning the cloning process,
make sure you have:

• A fully charged battery on each one of the
radios.

• Two Single Unit Chargers (SUC).

• Turned OFF the radios and,

• Both radios are of the same radio model.

2. Unplug any cables (power supply or USB
cables) from the SUCs.

3. Plug one side of the cloning cable mini
connector to one SUC. Plug the other end
to the second SUC.

Note: During the cloning process no power is
being applied to the SUC. The batteries will
not be charged. A data communication is
being established between the two radios.

4. Turn ON the Target radio and place it
into one of the SUCs.

• Long press the PTT button and SB2
simaltaneously while turning the radio ON.

• Wait for 3 seconds before releasing the
buttons until a distinctive audible tone is heard.

6. Place the Source radio” in its SUC, press
and release SB1.

7. After cloning is completed, the Source radio
will sound either a “pass” tone (cloning was
successful) or a “fail” tone (cloning process has
failed). The ‘pass’ tone sounds like a good key
‘chirp’ whereas the ‘fail’ tone sounds similar to
a ‘bonk’ tone. If the Source radio is a display
model it will either show ‘Pass’ or ‘Fail’ on the
display (a tone will be heard in no more than 5
seconds).

8. Once you have completed the cloning
process, turn the radios OFF and ON in order
to exit ‘clone’ mode.

PROGRAMMING

FEATURES

What to do if cloning fails

The radio will emit an audible ‘bonk’ indicating
that the cloning process has failed. In the event
that cloning fails, try performing each of the
following before trying to start the cloning
process again:

1. Ensure that the batteries on both radios are
fully charged.

2. Check the cloning cable connection on both
SUCs.

3. Ensure that the battery is engaged properly
on to the radio.

4. Ensure that there is no debris in the
charging tray or on the radio contacts.

5. Ensure that the Source radio is in cloning
mode.

Attention: This cloning cable is designed to
operate only with compatible Motorola
RLN6170 (Rapid) Single Unit Charger.

When ordering Cloning Cable please refer to
P/N RLN6303. For details about accessories
refer to Accessories section.

Cloning using the CPS (Computer
Programming Software)

When cloning using this method, you will need
to have the CPS software, a Drop-in Tray
Charger and the CPS Programming Cable.
Information on how to clone using the CPS is
available either in the CPS Help File -->
Content and Index --> Cloning Radios or in the
CPS Programming Cable Accessory Leaflet.

TROUBLESHOOTING

TROUBLESHOOTING

Symptom Try This

No Power

Recharge or replace the Li-Ion battery. Replace AA batteries.

Extreme operating temperatures affect battery life. Refer to ‘"About the Li-

Ion Battery" on page 11’.

Hearing other noises or

conversation on a

channel

Confirm Interference Eliminator Code is set. Frequency or Interference
Eliminator Code may be in use. Change settings: either change
frequencies or codes on all radios. Make sure radio is at the right frequency
and code when transmitting. Refer to "

"Talking and Monitoring" on page 24.

Message Scrambled

Scramble Code might be ON, and/or setting does not match other radios'

settings.

Limited talk range

Steel and/or concrete structures, heavy foliage, buildings or vehicles

decrease range. Check for clear line of sight to improve transmission.

Wearing radio close to body such as in a pocket or on a belt decreases

range. Change location of radio. Refer to

"Talking and Monitoring" on page

24.

TROUBLESHOOTING

Message not

transmitted/received

Make sure the PTT button is completely pressed if you're transmitting.

Confirm radios have the same Channel, Frequency, Interference

Eliminator Code and Scramble Code settings. Refer to the ‘Talking and

Monitoring’ Section on page

24 for further information.

Recharge, replace and/or reposition batteries. Refer to ‘About your Li-Ion

Battery’ section on page

11.

Obstructions and operating indoors, or in vehicles, may interfere: change

location. Refer to ‘Talking and Monitoring’ Section on page

24.

Verify that the radio is not in Scan Mode. Refer to the ‘“Scan” on page 40

“CPS (Computer Programming Software)” on page 42 and “Nuisance

Channel Delete” on page 41.

Heavy static or

interference

Radios are too close, they must be at least five feet apart. Radios are too

far apart or obstacles are interfering with transmission. Refer to the ‘Talking

and Monitoring’ Section on page

24.

Low batteries

Recharge or replace Li-Ion battery. Replace AA batteries. Extreme

operating temperatures affect battery life. Refer to ‘About the Li-Ion Battery’

Symptom Try This

TROUBLESHOOTING

Drop-in Charger LED

light does not come on

Check radio/battery is properly inserted and check battery/charger

contacts to be sure they are clean and charging pin is inserted correctly.

Refer to ‘Charging the Battery’ section on page

17, ‘Drop-in Tray Charger

LED Indicators’ section on page 21 and ‘Installing the Lithium-Ion Battery’

section on page 13.

Low battery indicator is

blinking although new

batteries are installed

Verify that the radio is set to the correct battery type. Refer to the ‘Installing

the Li-Ion Battery’ section on page

13, ‘"Installing Alkaline Battery Pack" on

page 14’ on page 14 and ‘About your Li-Ion Battery’ section on page 11.

Cannot activate VOX

VOX feature might not have been set to ON. Using CPS, make sure the

VOX Sensitivity level is not set to 0. Accessory not working or not

compatible. Refer to ‘Hands-Free Use/VOX’ section on page

28.

Battery doesn't charge

although it has been

placed in the drop-in

Check drop-in charger is connected and correspond to a compatible power

supply. Check you have the drop-in charger adjustable piece, placed on

the right position (refer to ‘Charging with the Drop-In Tray Single Unit

Charger’ and ‘Charging a Stand-Alone Battery’ section on page

18). Check

the charger LEDs indicators to see if battery has a problem. Refer to

Symptom Try This

USE AND CARE

USE AND CARE

Use a soft damp cloth

to clean the exterior

Do not immerse

in water

Do not use alcohol or

cleaning solutions

If the radio is submerged in water...

FREQUENCY AND CODE
CHARTS

The charts in this section provide Frequency
and Code information. These charts are useful

when using Motorola XTNi Series two-way
radios with other business radios. Most of the
frequency position are the same as Spirit M,
GT, S, XTN Series Frequencies.

8 Channel Radios PMR 446 Defaults

Freq # Frequency Code Bandwidth

1 446.00625 67.0 Hz 12.5kHz

2 446.01875 67.0 Hz 12.5kHz

3 446.03125 67.0 Hz 12.5kHz

4 445.04375 67.0 Hz 12.5kHz

5 446.05625 67.0 Hz 12.5kHz

6 446.06875 67.0 Hz 12.5kHz

7 446.08125 67.0 Hz 12.5kHz

8 446.09375 67.0 Hz 12.5kHz

9 446.00625 754.0 Hz 12.5kHz

10 446.01875 754.0 Hz 12.5kHz

11 446.03125 754.0 Hz 12.5kHz

12 445.04375 754.0 Hz 12.5kHz

FREQUENCY AND

CODE CHARTS

CTCSS

CTCSS Hz CTCSS Hz CTCSS Hz

1 67.0 14 107.2 27 167.9

2 71.9 15 110.9 28 173.8

3 74.4 16 114.8 29 179.9

4 77.0 17 118.8 30 186.2

5 79.7 18 123 31 192.8

6 82.5 19 127.3 32 203.5

7 85.4 20 131.8 33 210.7

8 88.5 21 136.5 34 218.1

9 91.5 22 141.3 35 225.7

10 94.8 23 146.2 36 233.6

11 97.4 24 151.4 37 241.8

12 100.0 25 156.7 38 250.3

13 103.5 26 162.2 122 (*) 69.3

DPL Codes (cont.)

DPL Code DPL Code DPL Code

39 23 61 152 83 343
40 25 62 155 84 346
41 26 63 156 85 351
42 31 64 162 86 364
43 32 65 165 87 365
44 43 66 172 88 371
45 47 67 174 89 411
46 51 68 205 90 412
47 54 69 223 91 413
48 65 70 226 92 423
49 71 71 243 93 431
50 72 72 244 94 432
51 73 73 245 95 445
52 74 74 251 96 464
53 114 75 261 97 465
54 115 76 263 98 466
55 116 77 265 99 503

FREQUENCY AND

CODE CHARTS

105 606 112 662 119 734
106 612 113 664 120 743
107 624 114 703 121 754
108 627 115 712
109 631 116 723
110 632 117 731
111 654 118 732

DPL Codes (cont.)

DPL Code DPL Code DPL Code

MOTOROLA LIMITED

WARRANTY

MOTOROLA LIMITED
WARRANTY

WARRANTY INFORMATION

The authorised Motorola dealer or retailer
where you purchased your Motorola two-way
radio and/or original accessories will honour a
warranty claim and/or provide warranty
service. Please return your radio to your dealer
or retailer to claim your warranty service. Do
not return your radio to Motorola. To be eligible
to receive warranty service, you must present
your receipt of purchase or a comparable
substitute proof of purchase bearing the date
of purchase. The two-way radio should also
clearly display the serial number. The warranty
will not apply if the type or serial numbers on
the product have been altered, deleted,
removed, or made illegible.

WHAT IS NOT COVERED BY THE
WARRANTY

• Defects or damage resulting from use of the
Product in other than its normal and
customary manner or by not following the
instructions in this user manual.

• Defects or damage from misuse, accident
or neglect.

• Defects of damage from improper testing,
operation, maintenance, adjustment, or any
alteration or modification of any kind.

• Breakage or damage to aerials unless
caused directly by defects in material or
workmanship.

• Products disassembled or repaired in such

MOTOROLA LIMITED

WARRANTY

• Defects or damage due to range.

• Defects or damage due to moisture, liquid
or spills.

• All plastic surfaces and all other externally
exposed parts that are scratched or
damaged due to normal use.

• Products rented on a temporary basis.

• Periodic maintenance and repair or
replacement of parts due to normal usage,
wear and tear.

ACCESSORIES

ACCESSORIES

AUDIO ACCESSORIES

BATTERY

CARRY ACCESSORIES

SOFTWARE APPLICATIONS

CABLES

Part No. Description

00115 Remote Speaker Mic BR

00168 Lightweight headset

00117 Headset w/Swivel Boom Mic

00118 Earbud w/Clip PTT Mic BR

Part No. Description

RLN6306 Alkaline Battery Frame

RLN6351 Standard Li-Ion Battery

RLN6305

High Capacity Li-Ion
Battery

Part No. Description

RLN6302 Hard Leather Carry Case

RLN6307 Spring Action Belt Clip

Part No. Description

IXEN4007ARComputer Programming Software

(CPS) and Programming Cable

Part No. Description

RLN6303 Radio To Radio Cable

ACCESSORIES

CHARGERS

Note:

(*) Attention: Certain accessories may be or may
not be available at the time of purchase. Please
contact your Motorola point of purchase or visit
www.motorola.com/XTNi or www.motorola.com/
radios/business for latest information on
accessories.

(**) European Rapid Charging Kit includes Power
Supply, Drop-in Tray Charger, and AC Pin adaptors.

Certain accessories may be or not available at the
time of purchase. Please contact your Motorola
Point of Purchase or visit www.motorola.com/XTNi
or www. motorola.com/radios/business for latest
information on accessories.

Contact your Motorola authorized dealer for
availability and accessories new models information

Part No. Description

IXPN4019ARRapid Charging Kit - European

(**)

IXPN4020ARMulti-Unit Charger (MUC) Kit -

European

MOTOROLA, the Stylized M Logo,XTNi Series and all other trademarks indicated
as such herein are trademarks of Motorola, Inc. ® Reg. U.S. Pat. & Tm. Off. All
other product or service names are the property of their respective owners. © 2007
Motorola, Inc. All rights reserved.