Motorola TWO WAY RADIO User Manual

1

Contents

SAFETY AND GENERAL INFORMATION

Transmit And Receive Procedure 2
Exposure To Radio Frequency Energy 2
Portable Radio Operation And EME Exposure 2
Electromagnetic Interference/Compatibility 3
Safety And General Use While Driving 4
Operational Warnings 4
Operational Cautions 5
Charger Safety Instructions 5

GETTING STARTED

Your New Radio 7
Batteries and Battery Charging 7
Installation of Batteries 7
The Battery Meter and Battery Alert 8
Battery Life 8
Charging Desk Stand 8
Turning Your Radio On And Off 9
Radio Etiquette 9

TALKING AND LISTENING

Volume 9
Monitor 9
Channel 9

Interference Eliminator Code 9
Time-Out Timer 10
Keypad Lock 10
Hands Free Use (VOX) 10

ALERTS

Channel Busy Indicator 11
Call Tone 11
Roger Beep (Talk Confirmation Tone) 11

ACCESSORIES

Belt Clip 11
Front Covers 11

FURTHER INFORMATION

Talk Range 12
Troubleshooting 13
Use And Care 14
Specifications 15
Warranty Information 15
Copyright Information 15

APPROVED ACCESSORIES LIST

Approved Accessories List 17

2

SAFETY AND GENERAL INFORMATION

IMPORTANT INFORMATION ON SAFE AND EFFICIENT
OPERATION

READ THIS INFORMATION BEFORE USING YOUR RADIO

The information provided in this document supersedes the
general safety information contained in user guides published
prior to July 2000.

This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.

TRANSMIT AND RECEIVE PROCEDURE

Your two-way radio contains a transmitter and a receiver. To
transmit (talk), you must push the M button; to receive (listen),
release the M button.

EXPOSURE TO RADIO FREQUENCY ENERGY

Your Motorola radio is designed to comply with the following
national and international standards and guidelines regarding
exposure of human beings to radio frequency electromagnetic
energy:

• United States Federal Communications Commission, Code of
Federal Regulations; 47 CFR part 2 sub-part J

• American National Standards Institute (ANSI) / Institute of
Electrical and Electronic Engineers (IEEE) C95. 1-1992

• Institute of Electrical and Electronic Engineers (IEEE) C95.1­1999 Edition

• International Commission on Non-Ionizing Radiation
Protection (ICNIRP) 1998

• Ministry of Health (Canada) Safety Code 6. Limits of Human
Exposure to Radiofrequency Electromagnetic Fields in the
Frequency Range from 3 kHz to 300 GHz, 1999

• Australian Communications Authority Radiocommunications
(Electromagnetic Radiation - Human Exposure) Standard 2001
(applicable to wireless phones only)

• ANATEL, Brasil Regulatory Authority, Resolution 256 (April 11,

2001) "additional requirements for SMR, cellular and PCS
product certification."

To assure optimal radio performance and make sure human
exposure to radio frequency electromagnetic energy is within
the guidelines set forth in the above standards, always adhere
to the following procedures:

PORTABLE RADIO OPERATION AND EME EXPOSURE

Antenna Care
Use only the supplied or an approved replacement antenna.

Unauthorized antennas, modifications, or attachments could
damage the radio and may violate FCC regulations.

DO NOT hold the antenna when the radio is "IN USE". Holding
the antenna affects call quality and may cause the radio to
operate at a higher power level than needed.

3

Two-way Radio Operation
When using your radio as a traditional two-way radio, hold the
radio in a vertical position with the microphone one to two
inches (2.5 to 5 cm) away from the lips.

Body-worn Operation

To maintain compliance with FCC/Health Canada RF exposure
guidelines, if you wear a radio on your body when transmitting,
always place the radio in a Motorola supplied or approved clip,
holder, holster, case, or body harness for this product. Use of
non-Motorola-approved accessories may exceed FCC/Health
Canada RF exposure guidelines. If you do not use one of the
Motorola-supplied or approved body-worn accessories, and
are not using the radio held in the normal use position, ensure

the radio and its antenna are at least one inch (2.5 cm) away
from your body when transmitting.

To control your exposure and ensure compliance with the
general population/uncontrolled environment exposure limits,
always adhere to the following procedure:

• Transmit no more than 50% of the time.

• To transmit (talk), push the Mbutton.

• To receive calls, release the M button.

Transmitting 50% of the time, or less, is important because the
radio generates measurable RF energy exposure only when
transmitting (in terms of measuring standards compliance).

Data Operation

If applicable, when using any data feature of the radio, with or
without an accessory cable, position the radio and its antenna
at least one inch (2.5 cm) away from the body.

ELECTROMAGNETIC INTERFERENCE/COMPATIBILITY
Note: Nearly every electronic device is susceptible to

electromagnetic interference (EMI) if inadequately shielded,
designed or otherwise configured for electromagnetic compatibility.

• Facilities

To avoid electromagnetic interference and/or compatibility
conflicts, turn off your radio in any facility where posted
notices instruct you to do so. Hospitals or health care facilities
may be using equipment that is sensitive to external RF energy.

• Aircraft

When instructed to do so, turn off your radio when on board an
aircraft. Any use of a radio must be in accordance with
applicable regulations per airline crew instructions.

• Devices

- Pacemakers

The Advanced Medical Technology Association recommends
that a minimum separation of 6 inches (15 centimeters) be
maintained between a handheld wireless radio and a
pacemaker. These recommendations are consistent with the
independent research by, and recommendations of, the United
States Food and Drug Administration.

4

Persons with pacemakers should:

• ALWAYS keep the radio more than six inches (15 centimeters)
from their pacemaker when the radio is turned ON.

• Not carry the radio in the breast pocket.

• Use the ear opposite the pacemaker to minimize the potential
for interference.

• Turn the radio OFF immediately if you have any reason to
suspect that interference is taking place.

- Hearing Aids

Some digital wireless radios may interfere with some hearing
aids. In the event of such interference, you may want to
consult your hearing aid manufacturer to discuss alternatives.

- Other Medical Devices

If you use any other personal medical device, consult the
manufacturer of your device to determine if it is adequately
shielded from RF energy. Your physician may be able to assist
you in obtaining this information.

SAFETY AND GENERAL USE WHILE DRIVING

Check the laws and regulations on the use of radio in the area
where you drive. Always obey them.

When using your radio while driving, please:

• Give full attention to driving and to the road.

• Use hands-free operation, if available.

• Pull off the road and park before making or answering a call
if driving conditions so require.

OPERATIONAL WARNINGS

• For Vehicles With An Air Bag

Do not place a portable radio in the area over an air bag or in
the air bag deployment area. Air bags inflate with great force.
If a portable radio is placed in the air bag deployment area and
the air bag inflates, the radio may be propelled with great
force and cause serious injury to occupants of the vehicle.

• Potentially Explosive Atmospheres

Turn off your radio prior to entering any area with a potentially
explosive atmosphere, unless it is a radio type especially
qualified for use in such areas as "Intrinsically Safe." Do not
remove, install, or charge batteries in such areas. Sparks in a
potentially explosive atmosphere can cause an explosion or
fire resulting in bodily injury or even death.

Note: The areas with potentially explosive atmospheres
referred to above include fueling areas such as below decks
on boats, fuel or chemical transfer or storage facilities, areas
where the air contains chemicals or particles, such as grain,
dust or metal powders, and any other area where you would
normally be advised to turn off your vehicle engine. Areas with
potentially explosive atmospheres are often but not always
posted.

• Blasting Caps And Areas

To avoid possible interference with blasting operations, turn
off your radio when you are near electrical blasting caps, in a
blasting area, or in areas posted: "Turn off two-way radio."
Obey all signs and instructions.

5

OPERATIONAL CAUTIONS

• Antennas

Do not use any portable radio that has a damaged antenna. If
a damaged antenna comes into contact with your skin, a minor
burn can result.

• Batteries

All batteries can cause property damage and/or bodily injury
such as burns if a conductive material such as jewelry, keys,
or beaded chains touch exposed terminals. The conductive
material may complete an electrical circuit (short circuit) and
become quite hot. Exercise care in handling any charged
battery, particularly when placing it inside a pocket, purse,
or other container with metal objects.

CHARGER SAFETY INSTRUCTIONS

Before using the battery charger, read all instructions and
cautionary markings on:

1. the battery

2. the battery charger, and

3. the radio using the battery.

Caution: To reduce the risk of injury, only charge the Motorola
approved rechargeable battery for this product. Other types of
batteries may burst, causing personal injury and damage.

SAVE THESE INSTRUCTIONS

1. Do not expose the charger to rain or snow.

2. Do not operate the charger if it has received a sharp blow,

or has been dropped or damaged in any way.

3. Do not disassemble the charger if it has received a sharp
blow, or has been dropped or damaged in any way.

4. Never alter the AC cord or plug provided with the unit. If the
plug will not fit the AC outlet, have proper outlet installed by
a qualified electrician. An improper condition can result in a
risk of electric shock.

5. To reduce the risk of damage to the cord or plug, pull by the
plug rather than the cord when disconnecting the charger
from the AC outlet.

6. To reduce the risk of electric shock, unplug the charger from
the AC outlet before attempting any maintenance or
cleaning.

7. Use of an attachment not recommended or sold by Motorola
may result in a risk of fire, electric shock, or personal injury.

8. Make sure the cord is located so that it will not be stepped
on, tripped over or subjected to damage or stress.

9. An extension cord should not be used unless absolutely
necessary. Use of an improper extension cord could result
in a risk of fire and/or electric shock. If an extension cord
must be used, make sure:

• That the pins on the plug of the extension cord are the same

number, size and shape as those on the plug of the charger.

• That the extension cord is properly wired and in good

electrical condition, and

• That the cord size is 18 AWG (1mm2) for lengths up to 100

feet (30 metres) and 16 AWG (1.3mm2) for lengths up to 150
feet (45 metres).

10. The supply cord of this charger cannot be replaced. If the

cord is damaged please return to your place of purchase.

6

Diagram of your Radio

Use P to:

• Turn power on/off

• Adjust volume

LED Indicator Light
Use M to:

• Talk

• Save a setting

Use ^ to:

• Transmit call tone

Removable Front Cover

Use \ to:

• Lock the keypad (when held
down and not in a menu)

• Exit the menu (when pressed
while in a menu)

Accessory Jack Cover
Use Q to:

• Monitor Channel Activity

Use [ ]to:

• Scroll through menus

Microphone

7

GETTING STARTED

Your New Radio

Your Motorola two-way radio operates on PMR446
frequencies, and can be used in any country where PMR446
frequencies are authorized, subject to applicable regulations.
This license-free, two-way radio service is for family and
group recreational use. Use of this radio outside the country
where it was intended to be distributed is subject to
government regulations and may be prohibited. Read this
manual carefully and make sure you know how to properly
operate the radio before use.

Please retain your original dated sales receipt for your
records. For warranty service of your Motorola two-way
radio you will need to provide a copy of your dated sales
receipt to confirm warranty status.

Batteries and Battery Charging

Your radio operates with 3 AA Alkaline batteries or a Nickel
Cadmium (NiCd) rechargeable battery pack. A rechargeable
upgrade kit is supplied with your radio.

Installation of AA Batteries

• Lift battery latch up to release the battery cover.

• Insert 3 AA batteries as shown.

• Reposition battery cover and press down until it clicks
into place.

Installation of NiCd Batteries

Caution: Do not disassemble
or unwrap the battery pack.

• Lift battery latch up to release
the battery cover.

• Insert NiCd battery pack.
Ensure the metal contacts on the side of the battery are
facing outwards from the radio to connect with contacts on
the battery door.

• Reposition battery cover and press down until it clicks
into place.

Note: Remove batteries before storing your radio for extended
periods. Batteries corrode over time and may cause permanent
damage to your radio. Exercise caution when handling batteries
that are leaking. Dispose of exhausted batteries at a designated
battery disposal unit and not in the household waste.

8

The Battery Meter and Battery Alert

The battery meter located in the top left hand corner of the
display indicates how much battery power you have remaining.

The radio will power off when the voltage drops below a
predetermined level, to protect the rechargeable battery.
When the battery meter is an empty shell a, the radio
chirps after releasing M and every 10 minutes.

Note: A fully charged NiCd battery pack may only display two
bars on the battery meter.

Battery Life

The approximate (typical) battery life for:
AA Alkaline batteries is 27 Hours
NiCd batteries is 12 Hours
This is based on a 5% transmit, 5% receive and 90%
standby cycle

Note: Battery life will be reduced if you regularly use Hands­Free (VOX) accessories.

Charging Desk Stand

The charging desk stand provides drop-in charging
convenience. The charging desk stand can be placed on any
flat surface, such as a desk or workbench. Charge the NiCd
battery overnight (16 hours) before using it for the first time.

• With the radio OFF, remove the battery cover.

• Insert the battery pack as indicated on the battery pack label.
The metal contacts on the side of the battery must be facing

outwards from the radio to connect with the contacts on the
battery door. Do not disassemble or unwrap the battery pack.

• Replace the battery cover.

• Insert the jack plug on the AC power supply into the socket
on the desk stand.

• Plug the AC power supply into a standard wall socket.

• Slide the radio into one of the desk stand charging pockets,
with the radio facing forward. The red light will glow if the
radio is properly inserted.

• The radio will be fully charged within 14 hours.

You can also charge the battery pack separately from the
radio, as follows:

• Insert the jack plug on the AC power supply into the socket
on the desk stand.

• Plug the AC power supply into a standard wall socket.

• Insert the battery pack into the desk stand charging pocket
using the charging pocket insert provided. Do not
disassemble or unwrap the battery pack.

• Make sure that the contacts on the side of the battery pack
align with the metal contacts in the pocket of the desk stand.
The red light will glow if the battery has been properly
inserted.

• The battery will be fully charged within 14 hours.

Charging Status

The solid red light indicator shows that the radio and/or the
NiCd battery are charging. A depleted battery will recharge to
full capacity within 14 hours.

9

Note: When moving between hot and cold environments, do not

charge the battery until the battery temperature acclimates
(usually about 20 minutes).

Note: For optimal battery life, remove the radio or battery from
the charger within 16 hours. Do not store the radio or the battery
in the charger.

Turning Your Radio On And Off

Turn Pclockwise to turn your radio on. The radio chirps and the
display will show all feature icons that your radio has available
for a brief period. The display will show the channel 1 - 8and
interference eliminator code 1 - 40. Turn Panticlockwise to
turn your radio off.

Radio Etiquette

It is good radio etiquette to monitor the channel for activity
before you transmit, to ensure that you do not interrupt other
users already on the channel.

Press and hold Q to check for channel activity. If you hear
static, the channel is clear for use.

TALKING AND LISTENING

Your radio has 8 channels and 40 interference eliminator codes. If
you are in a group and you wish to talk to each other, all radios
must be set to the same channel and code. Codes 39 and 40
are unique private codes for Neighbourhood Watch only and
allow communications with other Neighbourhood Watch radio
users that have the same radio. Your radio is compatible with
PMR446 or older NHW radios on channels 1- 8and codes
0- 38, but if you wish to use codes 39 and 40, your radio is
only compatible with radios of the same type as your radio. If you

experience interference and need to change channel, ensure
that you change the channel and code of all radios in your group.

• For maximum clarity, hold radio 5 to 7 centimetres from mouth.

• Press and hold Mand speak into the microphone. LED
indicator light glows continuously when transmitting.

• To receive messages, release M.

Volume

Use P to adjust your volume to a comfortable listening level.

Monitor

Pressing and holding Q allows you to monitor your channel for
activity.

Channel

• Press \. The channel number will begin to flash.

• Use ]or [to change channel.

• Press Mto set new channel.

Interference Eliminator Code

Interference eliminator codes help minimize interference by
providing you with a choice of code combinations.

• Press \ until the code number begins to flash.

• Use ]or [to change the code.

• Press Mto set new code.

You can specify a different code for each channel.

• To set a channel and code combination, press \and then
press ]or [to select the channel.

• Press \ again and then press ]or [to select a code.

• Press Mto exit the menu and to save the channel and code
combination.

10

To set another channel and code combination, repeat
these steps.

Time-out Timer

The Time-out Timer feature helps extend battery life by
preventing you from accidentally transmitting. The radio will
emit a continuous warning tone after Mis pressed for 60
continuous seconds and will stop transmitting.

Keypad Lock

The keypad lock disables the \, ]and [buttons. It allows
you to use the Q, M and ^ buttons.

Press and hold the \ button for three seconds to lock or unlock
the keypad. When the radio is locked f will show in the display.

Hands Free Use (VOX)

VOX allows you to transmit "hands free" by
talking while using VOX accessories
connected to the radio.

Note: When using audio accessories with
your radio, turn the volume of your radio down before you
place the accessory on your head or in your ear.

How To Use The VOX Feature

• Switch off your radio.

• Open the accessory cover and insert the audio accessory
into the accessory jack.

• Switch on your radio. The g icon will appear in the display
to indicate that the VOX feature is active.

• To transmit, speak into the accessory microphone. To receive,
stop talking.

• Pressing Mor removing audio accessory will disable VOX
operation.

Note: There is a short delay after you start talking, before the
radio transmits.

Setting Sensitivity Levels

Adjusting your radio’s VOX and/or microphone sensitivity level
helps to minimize the possibility of unintended noises
triggering a transmission, or enhances the ability to pick up
quiet voices.

If an accessory is fitted to your radio these instructions will
help you to adjust the VOX sensitivity and if no accessory is
fitted you will adjust the Microphone sensitivity.

• Press \ until g and a flashing number appear in the display.

• Select sensitivity level of 1, 2 or 3 by using ]or [.

1 - If you speak loudly, or are in a noisy environment.
2 - Suitable for most applications.
3 - If you speak softly, or are in a quiet environment.

Note: When you connect a VOX accessory, the radio will
automatically be set to the last chosen VOX sensitivity level.

11

ALERTS
Channel Busy Indicator

The red LED will flash twice per second to indicate that the
channel is in use.

Call Tone

Press ^ to transmit your call tone, alerting users on the
same channel and code that you are about to talk. Your radio
has 5 call tones to choose from. Setting the call tone to 0
disables ^.

To Set the Call Tone

• With the radio on, press \ until E appears in the display.

• Current call tone setting 0-5 will begin to flash.

• Press ] or [ to change and hear call tones while the

setting number is flashing.

• Press M to set new call tone.

Roger Beep (Talk Confirmation Tone)

When you turn on this feature, your two-way radio transmits a
unique tone when you finish transmitting. It’s like saying
'Roger' or 'Over', and lets others know you’ve finished talking.

• To enable or disable the roger beep, press and hold ] as

you turn your radio on.

• When the roger beep is enabled ! will show in the display.

• When you release the M button you will hear the roger beep.

ACCESSORIES
Belt Clip

Your radio comes with a swivel belt clip.

• To attach, align belt clip post with hole in
the radio back and gently push until it
clicks into place.

• To remove, push release tab on top of
belt clip down to release catch and pull
belt clip from the radio back.

Front Covers

Your radio has a removable front cover
that allows you to customize your radio.

Note: Do not operate your radio without the cover.

To Remove

• With a 1/8 inch flathead screwdriver, push down in between
the top of the front cover and the radio.

• Gently pry the cover away from the radio.

• Pull the top of the removable cover away from the radio.

To Attach

• Reinsert housing tabs at the bottom of the removable cover.

• Press down to snap cover into place.

12

FURTHER INFORMATION
Talk Range

Your radio has been designed to maximize performance and
improve transmission range in the field. It is recommended
that you do not use the radios closer than 1.5 meters apart,
to avoid interference.

Talk range depends on the terrain. It will be affected by
concrete structures, heavy foliage and by operating radios
indoors or in vehicles.

Optimal range occurs in flat, open areas, with up to 3
kilometres of coverage. Medium range occurs when
buildings and trees are in the way. Minimal range occurs
when dense foliage and mountains obstruct the
communication path.

Optimal Range

Outdoors

Flat, open areas

Medium Range

Outdoors

Buildings or trees

Also near

residential

buildings

Minimal Range

Outdoors

Dense foliage or

mountains

Also inside some

buildings

13

Troubleshooting

No power or erratic display Reposition, replace or recharge batteries.
Message not transmitted Make M button is completely pressed while you transmit.

Reposition, replace or recharge batteries.

Shared channel may be in use, try another channel.

Message not received Confirm radios have same channel settings and interference eliminator codes

(helps minimize interference).
Make sure M is not inadvertently being pressed.

Reposition, replace or recharge batteries.

Obstructions, and operating indoors or in vehicles may interfere with communication.
Change your location.

Check to make sure volume is turned up.

Hearing other conversation Shared channel may be in use, try another.
or noise on a Channel

Limited talk range Steel or concrete structures, heavy foliage and use in buildings and in vehicles will

decrease range. Check for clear line of sight to improve transmission.

Wearing radio close to body such as in a pocket or on a belt will decrease range.
Change location of radio.

Heavy static or interference Radios too close. Radios must be at least 1.5 metres apart.

Radios too far apart. Obstacles interfere with transmission.

14

Use and Care

To clean radio, use a

soft damp cloth

Do not immerse

in water

Do not use alcohol or

cleaning solutions

Turn it off and

remove batteries

Dry with soft cloth. Battery

contacts may be wiped with

a dry, lint-free cloth

Do not use until

completely dry

If the radio
gets wet...

15

Specifications

Channels 8
Codes 40
Operating Frequency 446.00625-446.09375 MHz
Talk Range Up to 3 kilometres
Power Source 3 AA alkaline batteries
Type Designation T5432
Transmitter Power (Watts) 0.5 ERP
Modulation Type Phase (Angle)
Channel Spacing (kHz) 12.5
Channel Protocol CTCSS

Warranty Information

How to Get Warranty Service

The authorised Motorola dealer or retailer where you
purchased your Motorola two-way radio and/or original
accessories will honour a warranty claim and/or provide
warranty service.

Please return your radio to your dealer or retailer to claim
your warranty service. Do not return your radio to Motorola.

In order to be eligible to receive warranty service, you must
present your receipt of purchase or a comparable substitute
proof of purchase bearing the date of purchase. The two-way
radio should also clearly display the serial number. The
warranty will not apply if the type or serial numbers on the
product have been altered, deleted, removed, or made illegible.

What Is Not Covered By The Warranty

1. Defects or damage resulting from use of the Product in

other than its normal and customary manner or by not
following the instructions in this user manual.

2. Defects or damage from misuse, accident or neglect.

3. Defects of damage from improper testing, operation,

maintenance, adjustment, or any alteration or
modification of any kind.

4. Breakage or damage to aerials unless caused directly by

defects in material or workmanship.

5. Products disassembled or repaired in such a manner as

to adversely affect performance or prevent adequate
inspection and testing to verify any warranty claim.

6. Defects or damage due to range.

7. Defects or damage due to moisture, liquid or spills.

8. All plastic surfaces and all other externally exposed parts

that are scratched or damaged due to normal use.

9. Products rented on a temporary basis.

10. Periodic maintenance and repair or replacement of parts

due to normal usage, wear and tear.

Copyright Information

The Motorola products described in this manual may include
copyrighted Motorola programs, stored semiconductor
memories or other media. Laws in the United States and
other countries preserve for Motorola, certain exclusive
rights for copyrighted computer programs, including the
exclusive right to copy or reproduce in any form, the
copyrighted Motorola programs.

16

Accordingly, any copyrighted Motorola computer programs
contained in the Motorola products described in this manual
may not be copied or reproduced in any manner without express
written permission of Motorola. Furthermore, the purchase of
Motorola products shall not be deemed to grant either directly or
by implication, estoppel, or otherwise, any license under the
copyrights, patents or patent applications of Motorola, except for
the normal non-exclusive royalty free license to use that arises
by operation of law in the sale of a product.

, MOTOROLA are trademarks of Motorola Inc.

© 2003 Motorola Inc.

For use in:
Austria, Belgium, Denmark, Finland, France, Germany,
Iceland, Ireland, Italy, Luxembourg, The Netherlands,
Portugal, Spain, Switzerland, United Kingdom, Sweden.

0359

17

APPROVED ACCESSORIES LIST

Please contact your dealer or retailer to purchase these accessories

Earbud with Push-To-Talk
Microphone ENTN8870

Discreet, lightweight earpiece with
hand-operated lapel or collar
mounted microphone. Allows clear
communication without disturbance
or interference.

Rechargeable NiCd Battery
HKNN4002

It is always nice to know you have
good back up. A rechargeable
battery pack – have one spare for
those busy times.

NiCd Rechargeable Battery Upgrade
Kit IXPN4004 (UK)/IXPN4005 (EURO)

The NiCd rechargeable battery
upgrade kit is used to charge the
NiCd batteries for T5412 and T5422
radios. The kit includes two NiCd
batteries, a charging stand and two
charging pocket inserts.

Waterproof Bag EHLN9580

Clear plastic waterproof bag offers
protection from the elements and
submersion while still enabling your
radio to be operated. A must for
watersports fans.

Nylon Carry Case ENTN9153

Nylon pouch with a loop that attaches
to your belt to hold your radio securely.
Supplied with extra loops so you can
fix to rucksacks or bikes. Can be used
with audio accessories.

Headset with Boom Microphone
ENTN8868

Comfortable, lightweight headset
eliminates background noise.
Provides access to the voice activated
transmission (VOX) mode. Ideal for
situations which require hands-free
operation.