TM
MVME5100 Series
VME Processor Modules
™
♦ PowerPC 7400 or PowerPC 750
microprocessor with 32KB /32KB L1 cache
♦ Up to 2MB of secondary backside cache
♦ 100 MHz front-side bus
♦ 64MB, 128MB, or 512MB of on-board
ECC SDRAM—expandable up to 1GB
with optional RAM500 mem ory ex pan si on
modules
♦ Up to 17MB Flash memory
♦ Dual IEEE P1386.1 compa tible 32/64- bit
PMC expansion slots
♦ 64-bit PCI expansion mezzanine
connector allowing up to four more PMCs
♦ Dual 16550 compatible async serial ports
♦ Dual 10BaseT/100BaseTX Ethernet
♦ 32KB NVRAM and time-of-day clock with
replaceable battery backup
♦ Four 32-bit timers, one watchdog timer
♦ On-board debug monitor
♦ Single VME slot even when fully
configured with two PMC modules and
both add-on memory mezzanines
Supercomputing levels of performance in a scalable, single-board
computer
The MVME5100 is a high-performance VME processor module featuring the
Motorola Computer Group (MCG) PowerPlus II architecture with a choice of
®
PowerPC
processors—either Motorola’s MPC7400 with AltiVec™ technol-
ogy for algorithmic-intensive computations or the low-power MPC750.
Based on an integrated PCI bridge–memory controller ASIC designed by
MCG, PowerPlus II takes memory performance to new levels with 582MB/s
memory read bandwidth and 640MB/s burst write bandwidth. Plus, PowerPlus II architecture supports full PCI throughput of 264MB/s without starving
the CPU from its memory.
The MVME5100 is designed to m eet the needs of OEMs servicing the mi litary
and aerospace, indus trial automatio n, and semicon ductor process equi pment
market segments.
60x
Arbiter
Vcore
REG
+3.3V
REG
L2 Cache
1MB or 2MB
MPC7400
MPC750
Hawk ASIC
PCI
Expansion
SDRAM Expansion
256MB
SDRAM Expansion
64 or 256MB
ECC SDRAM
64, 128 or 512MB
100 MHz Memory Bus
64-bit/33 MHz Local PCI Bus
PMC2 PMC1
Rows D & Z
46-pins
64-pins
BUF
FP I/OFP I/O
Rows A & C
Flash
1MB
Flash
16MB
X-Bus
RTC
NVRAM
VME
Universe2B
Serial
16550
Serial
16550
P1P2
Serial
RJ-45
Ethernet
82559ER
Ethernet
82559ER
RJ-45
RJ-45
SCSI
LSI
16-bit SCSI
PCI
PMC P11 & P12
PIB
WB-554
Super I/O
National
COM1
COM2
PMC P14 & P15
MVME5100 Block Diagram IPMC Block Diagram
ISA
ESCC
85230
Parallel
SER3 Sync (761) Async (712)
SER4 (Sync)
P2 MUX
PAL
(IPMC761)
P2 MUX
CIO
8536
MVME5100 P2 I/O
MVME5100 P2 I/O
I/O Compatibility
Historically, MCG has offered two tracks in its Po werPC VME
portfolio. The first track (which includes the MVME2600/
2700) provides typical single-board computer I/O features
including Ethernet, SCSI , multip le serial p orts, a pa rallel p ort,
and a single PMC slot. The on-board I/O is routed to P2 and
made available to the user via MCG’s MVME761 or
MVME712M transition boards. The second track (which
includes the MVME2300/2400) offers limited on-board I/O
(Ethernet and a single s eri al p ort b oth vi a the front panel) but
provides dual PMC s lots en abling maximum u ser I/ O cus tom ization.
The MVME5100 merges the best features of both tracks
enabling the OEM to support varying I/O requirements with
the same base platform, simplifying part number maintenance, technical expertise requirements, and sparing.
P2 I/O Modes
The MVME5100 supports two, jumper-configurable P2 I/O
modes, PMC mode and IPMC mode.
PMC mode is backward compatible with the MVME2300/
MVME2400. In PMC mode, 64 pins from PMC Slot 1 and 46
pins from PMC Slot 2 are available on P2 for PMC rear I/O.
In IPMC mode, the MVME5100 supports legacy MVME761 or
MVME712M I/O modules (with limited PMC I/O) when an
IPMC761 or IPMC712 PMC card is pop ula ted in PM C Slot 1.
In this configuration, PMC Slot 2 contains some signals that
are reserved for extended SCSI.
IPMC Modules
The IPMC761 and IPMC712 are optional add-on PMC modules that provide backward compatibility with previous-generation MCG products (such as MVME2600 and MVME2700)
using the MVME761 or MVME712M transition board. IPMC
modules provide rear I/O support for
• one single-ended Ultra Wide SCSI port
• one parallel port
• four serial ports (2 or 3 async and 1 or 2 sync/async,
depending on module)
With this PMC card configuration, the memory mezzanine,
one PMC slot, and the PMCspan are still available, providing
support for OEM product customization.
Transition Modules
Transition Modules
MVME761
The MVME761 transition module provides industry-standard
connector access to the IEEE 1284 parallel port, a 10BaseT
or 100BaseT port via an RJ-45 connector, two DB-9 connectors providing acc es s to the asynchronous seri al p orts co nfigured as EIA-574 DTE, and two HD-26 connectors providing
access to the sync/async serial ports. These serial ports,
labeled as Serial 3 and Serial 4 on the faceplate of the
MVME761, are individually user-configurable as EIA-232,
EIA-530, V.35, or X.21 DCE or DTE via the installation of
Motorola Serial Interface Modules (SIMs).
A P2 adapter provides interface module signals to the
MVME761 transition module. The 3-row P2 adapter can be
used for 8-bit SCSI. A 5-row P2 adapter supports 16 -bit SCSI
and PMC I/O.
MVME712M
The MVME712M transition module provides industry-standard connector ac ce ss to the Ce ntro ni cs® parallel port, a nar-
row SCSI port, and four DB-25 connectors providing access
to the asynchronous/synchronous serial ports jumper configurable as EIA-232 DCE or DTE. A P2 adapter provides inter-
face signals to the MVME712M transition module. The 3-row
P2 adapter can be used for 8-bit SCSI.
To gain access to the additional user definable I/O pins provided via the 5-row VME6 4 extensi on connec tor , a s pecial P2
adapter board is available. This adapter panel replaces the
traditional 3-row P2 adap ter a nd e xtends its ca pab ility by providing access to the PMC I/O pins.
Software Support
Software Support
Firmware Monitor
Firmware must fulfill the tra dition al functi ons of test a nd ini tialization and provide operating system boot support. The
MVME5100 firmware monitor exceeds these requirements
with a proven monitor from the embedded VME leader. It
expands features like power-up tests with extensive diagnostics, as well as a powerful evaluation and debug tool for simple checkout or when high-level development debuggers
require additional support. All this is included with the
MVME5100 firmware ; pl us it s upp orts bo oting both operating
systems and kernels.
Operating Systems and Kernels
MVME5100 supports booting a variety of operating systems
including a complete range of real-time operating systems
and kernels which may be purchased from the follo w ing com panies:
Wind River Systems, Inc.:
Multiple Partners:
VxWorks
Linux
Specifications
®
®
Specifications
MVME5100 Processor Module
MVME5100 Processor Module
Processor
Microprocessor:
Clock Frequency:
On-chip Cache (I/D):
Secondary Cache:
MPC7400 MPC750
400 MHz 450 MHz
32K/32K 32K/32K
1MB or 2MB 1MB
Main Memory
Type:
PC100 ECC SDRAM with 100 MHz bus
Capacity:
Single Cycle Accesses:
Read Burst Mode:
Write Burst Mode:
Architecture:
64MB, 128MB, or 512MB on board,
expandable to 1GB with RAM500 memory mezzanines
10 Read/5 Write
7-1-1-1 idle; 2-1-1-1 aligned page hit
4-1-1-1 idle; 2-1-1-1 aligned page hit
64-bit, single interleave
Flash Memory
Type:
EEPROM, on-board programmable
Capacity:
1MB via two 32-pin PLCC/CLCC sockets;
16MB surface mount
Read Access (16MB
Read Access (1MB
70 clocks (32-byte burst)
port):
262 clocks (32-byte burst)
port):
NVRAM
Capacity:
Cell Storage Life:
Cell Capacity Life:
Removable Battery:
32KB (4KB available for users)
50 years at 55° C
5 years at 100% duty cycle, 25° C
Yes
Counters/Timers
TOD Clock Device:
Real-Time Timers/
Counters:
Watchdog Timer:
M48T37V
Four, 32-bit programmable
Time-out generates reset
VMEbus ANSI/VITA 1-1994 VME64 (IEEE STD 1014)
Controller:
DTB Master:
DTB Slave:
Arbiter:
Interrupt Handler/
Generator:
System Controller:
Location Monitor:
Tundra Universe
A16–A32; D08–D64, BLT
A24–A32; D08–D64, BLT, UAT
RR/PRI
IRQ 1–7/Any one of seven IRQs
Yes, jumperable or auto detect
Two, LMA32
Ethernet Interface
Controller:
Interface Speed:
PCI Local bus DMA:
Connector:
Two Intel 82559ER
10/100Mb/s
Yes, with PCI burst
One routed to front panel RJ-45, one
routed to front panel RJ-45 or optionally
routed to P2, RJ-45 on MVME761
Asynchronous Serial Ports
Controller:
Number of Ports:
Configuration:
Async Baud Rate, bps
Connector:
16C550C UART
Two, 16550 compatible
EIA-574 DTE
38.4K EIA-232, 115Kbps raw
max.:
One routed to front panel RJ-45, one on
planar for development use
Dual IEEE P1386.1 PCI Mezzanine Card Slots
Address/Data:
PCI Bus Clock:
Signaling:
Power:
Module Types:
A32/D32/D64, PMC PN1, PN2, PN3,
PN4 connectors
33 MHz
5V
+3.3V, +5V, ±12V; 7.5 watts maximum
per PMC slot
Two single-wide or one double-wide, front
panel or P2 I/O
PCI Expansion Connector
Address/Data:
PCI Bus Clock:
Signaling:
Connector:
A32/D32/D64
33 MHz
5V
114-pin connector located on the planar
of the MVME5100
Power Requirements
(not including power required by PMC or IMPC modules)
MVME5100:
MVME5100 with
MVME761:
+5V ± 5% +12V ± 10% –12V ± 10%
3.0 A typ. 8.0 mA typ. 2.0 mA typ.
3.2 A typ.,
4.0 A max.
0.2 A typ.
0.5 A max.
0.1 A typ.
0.3 A max.
Board Size
Height:
Front Panel Height:
Max. Component
Height:
233.4 mm (9.2 in.)
Depth:
160.0 mm (6.3 in.)
261.8 mm (10.3 in.)
Width:
19.8 mm (0.8 in.)
14.8 mm (0.58 in.)
IPMC Modules
IPMC Modules
PMC Interface
Address/Data:
PCI Bus Clock:
Signaling:
Module Type:
A32/D32/D64, PMC PN1, PN2, PN3,
PN4 connectors
33 MHz
5V
Basic, single-wide; P2 I/O
SCSI Bus
Controller:
PCI Local Bus DMA:
Asynchronous (8-bit
mode):
Ultra SCSI:
Note: 16-bit SCSI operation precludes the use of some PMC Slot 2
signals.
Symbios 53C895A
Yes, with PCI local bus burst
5.0MB/s
20.0MB/s (8-bit mode), 40.0MB/s (16-bit
mode)
Synchronous Serial Ports
Controller:
Number of Ports:
Configuration:
Baud Rate, bps max.:
Oscillator Clock Rate
(PCLK):
85230/8536
Two (IPMC761); one (IPMC712)
IPMC761: TTL to P2 (both ports), SIM
configurable on MVME761;
IPMC712: EIA-232 to P2
2.5M sync, 38.4K async
10 MHz/5 MHz
Asynchronous Serial Ports
Controller:
Number of Ports:
Configuration:
Async Baud Rate, bps
16C550 UART; 85230/8536
Two (IPMC761); three (IPMC712)
EIA-574 DTE (IPMC761);
EIA-232 (IPMC712)
38.4K EIA-232, 115Kbps raw
max.:
Parallel Port
Controller:
Configuration:
Modes:
PC97307
8-bit bi-directional, full IEEE 1284 sup-
port; Centronics compatible (minus EPP
and ECP on MVME712M)
Master only
Power Requirements
(additional power load placed on MVME5100 with IPMC installed)
IPMC761 IPMC712
+5V:
0.5 A max. 0.5 A max.
+3.3V
0.75 A max. 0.75 A max.
Transition Modules
Transition Modules
I/O Connectors
MVME761 MVME712M
Asynchronous
Serial Ports:
Two, DB-9 labeled as
COM1 and COM2
Three, DB-25 labeled
as Serial 1, Serial 2,
and Serial 3
Synchronous
Serial Ports:
Two HD-26 labeled as
Serial 3 and Serial 4
One, DB-25 labeled as
Serial 4
(user configurable via
installation of SIMs),
Two 60-pin connectors
on MVME761 planar
for installation of two
SIMs
Parallel Port:
Ethernet:
HD-36, Centronics
compatible
10BaseT or
D-36, Centronics com-
patible
not available
100BaseTX, RJ-45
SCSI:
8- or 16-bit, 50- or 68pin connector via P2
8-bit, standard SCSI D-
50
adapter
Board Size
Height:
Depth:
Front Panel Hei ght:
Front Panel Width:
233.4 mm (9.2 in.)
80.0 mm (3.1 in.)
261.8 mm (10.3 in.)
MVME761: 19.8 mm (0.8 in.)
MVME712M: 39.6 mm (1.6 in.)
All Modules
All Modules
Environmental
(Minimum of 400 LFM (linear feet per minute) of forced air cooling is
recommended for operation in the higher temperature ranges.)
Temperature:
Humidity (NC):
Vibration:
Operating Nonoperating
0° C to +55° C
–40° C to +85° C
(inlet air temp. w/forced
air cooling)
5% to 90% 5% to 90%
2 Gs RMS,
20–2000 Hz random
20–2000 Hz random
6 Gs RMS,
Demonstrated MTBF
(based on a sample of eight boards in accelerated stress environment; results pending for IPMC712)
Mean:
190,509 hours
95% Confidence:
107,681 hours
Safety
All printed wiring boards (PWBs) are manufactured with a flammability rating of 94V-0 by UL recognized manufacturers.
Electromagnetic Compatibility (EMC)
Intended for use in systems meeting the following regulations:
U.S.:
FCC Part 15, Subpart B, Class A (non-residential)
Canada:
ICES-003, Class A (non-residential)
This product was tested in a representative system to the following
standards:
CE Mark per European EMC Directive 89/336/EEC with Amendments; Emissions: EN55022 Class B; Immunity: EN55024
(results pending for configurations with IPMC712)
Ordering Information
Ordering Information
All models of the MVME5100 are available with either VME Scanbe
front panel (-01
Part Number Description
MPC750 configurations with 450 MHz MPC750, 17MB Flash and
1MB L2 cache
MVME5100-013
MVME5100-016
MPC7400 configurations with 400 MHz MPC7400 and 17MB Flash
MVME5101-013
MVME5101-016
MVME5101-213
MVME5101-214
MVME5101-216
x
1) or IEEE 1101 compatible front panel (-01x3).
x
64MB ECC SDRAM
x
512MB ECC SDRAM
x
64MB ECC SDRAM, 1MB L2 cache
x
512MB ECC SDRAM, 1MB L2 cache
x
64MB ECC SDRAM, 2MB L2 cache
x
128MB ECC SDRAM, 2MB L2 cache
x
512MB ECC SDRAM, 2MB L2 cache
I/O Modules
MVME712M Compatible I/O
IPMC712-001
MVME712M
Multifunction rear I/O PMC module; Ultra
Wide SCSI, one parallel port, three async and
one sync/async serial ports
Transition module connectors: One DB-25
sync/async serial port, three DB-25 async
serial port, one AUI connector, one D-36 parallel port, and one 50-pin 8-bit SCSI; includes
3-row DIN P2 adapter module and cable
MVME761 Compatible I/O
IPMC761-001
Multifunction rear I/O PMC module; Ultra
Wide SCSI, one parallel port, two async and
two sync/async serial ports
MVME761-001
Transition module: T wo DB-9 async serial port
connectors, two HD-26 sync/async serial port
connectors, one HD-36 parallel port connector, one RJ-45 10/100 Ethernet connector;
includes 3-row DIN P2 adapter module and
cable (for 8-bit SCSI)
MVME761-011
Transition module: T wo DB-9 async serial port
connectors, two HD-26 sync/async serial port
connectors, one HD-36 parallel port connector, and one RJ-45 10/100 Ethernet connector; includes 5-row DIN P2 adapter module
and cable (for 16-bit SCSI); requires backplane with 5-row DIN connectors
SIM232DCE or DTE
SIM530DCE or DTE
SIMV35DCE or DTE
SIMX21DCE or DTE
EIA-232 DCE or DTE Serial Interface Module
EIA-530 DCE or DTE Serial Interface Module
V.35 DCE or DTE Module
X.21 DCE or DTE Serial Interface Module
Related Products
PMCSPAN-002
PMCSPAN-010
RAM500-004
RAM500-006
RAM500-016
Primary 32-bit PCI expansion, mates directly
to the MVME5100 providing slots for either
two single-wide or one double-wide PMC
cards; optional PMCSPAN-010
Secondary 32-bit PCI expansion, plugs
directly into PMCSPAN-002 providing two
additional PMC slots
Stackable (top) 64MB ECC SDRAM mezzanine
Stackable (top) 256MB ECC SDRAM mezzanine
Stackable (bottom) 256MB ECC SDRAM
mezzanine
Documentation
V5100A/IH
V5100A/PG
VME761A/IH
VME712MA/IH
PPCBUGA1/UM
PPCBUGA2/UM
PPCDIAA/UM
Documentation is available for online viewing and ordering at http://
www.motorola.com/computer/literature.
MVME5100 Installation and Use
Programmer’s Reference Guide
MVME761 Transition Module Installation and
Use
MVME712 Transition Module Installation and
Use
PPCBug Firmware Package User’s Manual
(volumes one and two)
PPCBug Diagnostics Manual
www.motorola.com/computer 1-800-759-1107
Motorola Computer Group Worldwide Headquarters: 2900 S. Diablo Way, Tempe, AZ 85282
Sales Offices:
86 64 24 •
905-507-7200 •
Motorola and the stylized M logo are registered trade marks and the Intelligen ce Eve rywhere logo, AltiVec, Digital DNA and the Digital DNA logo are tr adem arks of Motor ola, In c. PowerP C and
the PowerPC logo are registered tradema rks and Pow erPC 750 is a tradem ark of In terna ti onal Busi ness Ma chines Cor pora tion and are used by Motorola, Inc. under license from International
Business Machines Corporation. VxWorks is a registered trademark of Wind River Systems, Inc. Linux is a registered trademark of Linus Torvalds. Centronics is a registered trademark of
Centronics Data Computer Corporation. All other product or service names are the property of their respective owners.
This datasheet identifies products, th eir specific a tions, an d their ch aract eristi cs, which m ay be suita bl e for certai n a pplications. It does not constitute an offer to sell or a comm itmen t of pre sent
or future availability, and should not be relied upon to state the terms and conditions, including warranties and disclaimers thereof, on which Motorola may sell products. A prospective buyer
should exercise its own independent jud geme nt to confir m the su itability o f the products for par ticular applicatio ns. M otor ola reserve s the right to make changes, without notice, to any produ cts
or information herein which will, in its sole discretion, improve reliability, function, or design. Motorola does not assume any liability arising out of the application or use of any product or circuit
described herein; neither does it convey any license under its patent or other intellectual property rights or under others. This disclaimer extends to any prospective buyer, and it includes
Motorola’s licensee, licensee’s transferees, and licensee’s customers and users. Availability of some of the products and services described herein may be restricted in some locations.
® Reg. U.S. Pat. & Tm. Off. © 1999, 2000, 2001 Motorola, Inc. All rights reserved. M5100-D8 9/01
United Kingdom:
Germany:
+49 (0) 611-3611 604 •
Eastern Pan America:
+44 (0) 1256 790555 •
East Mediterranean:
508-357-8260 •
Asia Pacific and Japan:
Western Pan America:
972-3-568-4388 •
852-2966-3210 •
Canada & Central Pan America:
408-991-8634
France:
+33 (0) 1 64
Loading...