Motorola MC74HCT241ADW, MC74HCT241AN Datasheet



SEMICONDUCTOR TECHNICAL DATA

1

REV 6

 Motorola, Inc. 1995

10/95

& && "!!($&! '$! $($ ! ($ )& " #& !#'&%

High–Performance Silicon–Gate CMOS

The MC54/74HCT241A is identical in pinout to the LS241. This device may be used as a level converter for interfacing TTL or NMOS outputs to High–Speed CMOS inputs. The HCT241A is an octal noninverting buffer/line driver/line receiver designed to be used with 3–state memory address drivers, clock drivers, and other bus–oriented systems. The device has non–inverted outputs and two output enables. Enable A is active–low and Enable B is active–high.

The HCT241A is similar in function to the HCT244. See also HCT240.

• Output Drive Capability: 15 LSTTL Loads

• TTL/NMOS–Compatible Input Levels

• Outputs Directly Interface to CMOS, NMOS, and TTL

• Operating Voltage Range: 4.5 to 5.5 V

• Low Input Current: 1 µA

• In Compliance with the Requirements Defined by JEDEC Standard

No. 7A

• Chip Complexity: 118 FETs or 29.5 Equivalent Gates

LOGIC DIAGRAM

DATA INPUTS

A1

A2

A3

A4

B1

B2

B3

B4

17

15

13

11

8

6

4

2 18

16

14

12

9

7

5

3

YB4

YB3

YB2

YB1

YA4

YA3

YA2

YA1

NONINVERTING OUTPUTS

PIN 20 = V

CC

PIN 10 = GND

OUTPUT

ENABLES

ENABLE A ENABLE B

1 19



PIN ASSIGNMENT

FUNCTION TABLE

Inputs Output

Enable A A YA

L L L L H H H X Z

Inputs Output

Enable B B YB

H L L H H H L X Z

A3

A2

YB4

A1

ENABLE A

GND

YB1

A4

YB2

YB3 5

4

3

2

1

10

9

8

7

6

14

15

16

17

18

19

20

11

12

13

YA2

B4

YA1

ENABLE B

V

CC

B1

YA4

B2

YA3

B3

Z = high impedance X = don’t care

DW SUFFIX

SOIC PACKAGE

CASE 751D–04

N SUFFIX

PLASTIC PACKAGE

CASE 738–03

ORDERING INFORMATION

MC54HCTXXXAJ MC74HCTXXXAN MC74HCTXXXADW

Ceramic Plastic SOIC

J SUFFIX

CERAMIC PACKAGE

CASE 732–03

1

20

1

20

1

20

MC54/74HCT241A

MOTOROLA High–Speed CMOS Logic Data

DL129 — Rev 6

2

MAXIMUM RATINGS*

Symbol

Parameter

Value

Unit

V

CC

DC Supply Voltage (Referenced to GND)

– 0.5 to + 7.0

V

in

DC Input Voltage (Referenced to GND)

– 1.5 to VCC + 1.5

V

out

DC Output Voltage (Referenced to GND)

– 0.5 to VCC + 0.5

V

I

in

DC Input Current, per Pin

± 20

mA

I

out

DC Output Current, per Pin

± 35

mA

I

CC

DC Supply Current, VCC and GND Pins

± 75

mA

P

D

Power Dissipation in Still Air,Plastic or Ceramic DIP†

SOIC Package†

750 500

mW

T

stg

Storage Temperature

– 65 to + 150

_

C

T

L

Lead Temperature, 1 mm from Case for 10 Seconds

(Plastic DIP or SOIC Package)

(Ceramic DIP)

260 300

_

C

*Maximum Ratings are those values beyond which damage to the device may occur.

Functional operation should be restricted to the Recommended Operating Conditions.

†Derating — Plastic DIP: – 10 mW/_C from 65_ to 125_C

Ceramic DIP: – 10 mW/_C from 100_ to 125_C SOIC Package: – 7 mW/_C from 65_ to 125_C

For high frequency or heavy load considerations, see Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).

RECOMMENDED OPERATING CONDITIONS

Symbol

Parameter

Min

Max

Unit

V

CC

DC Supply Voltage (Referenced to GND)

4.5

5.5

V

Vin, V

out

DC Input Voltage, Output Voltage (Referenced to GND)

0

V

CC

V

T

A

Operating Temperature, All Package Types

– 55

+ 125

_

C

tr, t

f

Input Rise and Fall Time (Figure 1)

0

500

ns

DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND)

Guaranteed Limit

Symbol

Parameter

Test Conditions

V

CC V

– 55 to

25_C

v

85_Cv 125_C

Unit

V

IH

Minimum High–Level Input Voltage

V

out

= 0.1 V or VCC – 0.1 V

|I

out

| v 20 µA

4.5

5.5

2 2

V

IL

Maximum Low–Level Input Voltage

V

out

= 0.1 V or VCC – 0.1 V

|I

out

| v 20 µA

4.5

5.5

0.8

0 8

0.8

V

OH

Minimum High–Level Output Voltage

Vin = VIH or V

IL

|I

out

| v 20 µA

4.5

5.5

4.4

5.4

4.4

5.4

4.4

5.4

V

Vin = VIH or V

IL

|I

out

| v 6 mA

4.5

3.98

3.84

3.7

V

OL

Maximum Low–Level Output Voltage

Vin = VIH or V

IL

|I

out

| v 20 µA

4.5

5.5

0.1

V

Vin = VIH or V

IL

|I

out

| v 6 mA

4.5

0.26

0.33

0.4

I

in

Maximum Input Leakage Current

Vin = VCC or GND

5.5

± 0.1

± 1.0

µA

I

OZ

Maximum Three–State Leakage Current

Output in High–Impedance State Vin = VIL or V

IH

V

out

= VCC or GND

5.5

± 0.5

± 5.0

± 10

µA

I

CC

Maximum Quiescent Supply Current (per Package)

Vin = VCC or GND I

out

= 0 µA

5.5

4

40

160

µA

This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high–impedance circuit. For proper operation, Vin and V

out

should be constrained to the

range GND v (Vin or V

out

) v VCC.

Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open.

MC54/74HCT241A

High–Speed CMOS Logic Data DL129 — Rev 6

3 MOTOROLA

∆I

CC

Additional Quiescent Supply

Vin = 2.4 V, Any One Input

≥ –55_C

25_C to 125_C

Current

Vin = VCC or GND, Other Inputs l

out

= 0 µA

5.5

2.9

2.4

mA

NOTES:

1. Information on typical parametric values along with frequency or heavy load considerations can be found in Chapter 2 of the Motorola High– Speed CMOS Data Book (DL129/D).

2. Total Supply Current = ICC + Σ∆ICC.