TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
CAUTION:
WARNING
The unauthorized modification of any unit and the sale and use of any
such unit is prohibited by law. Any such modification or alteration of
this product or any unauthorized reception of television programming
could subject the user and seller and party modifying the unit to fines,
imprisonment, and civil damages.
OPERATION PRECAUTIONS
WARNING: TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS EQUIPMENT
TO RAIN OR MOISTURE.
NOTE: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful,
interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
This digital apparatus does not exceed the Class A limits of radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
Repairs and Assistance
For assistance on return or repair see "Product Support" on page 69.
Note to CATV System Installer
This reminder is provided to call the CATV system installer’s attention
to Article 820-40 of the National Electric Code (NEC) that provides
guidelines for proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
Warning
To prevent electrical shock, do not use the unit electrical power plug
(polarized) with an extension cord, receptacle, or other outlet unless the
blades can be fully inserted to prevent blade exposure. The mains
disconnect device is the appliance plug and it shall remain readily
accessible and operable.
The lithium battery is not field-replaceable for the life of the product.
General Instrument Corporation doing business as
Motorola Mobility, Inc.
6450 Sequence Dr.
San Diego, CA 92121
DOCUMENT No: 578523-001 REV B, 12/9/10
The lightning flash with the arrowhead symbol,
within an equilateral triangle, is intended to alert the
user to the presence of un-insulated “dangerous
voltage” within the product’s enclosure that may be
of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
ATTENTION
This commercial unit is intended for the decoding of
DigiCipher
Possession of this device does not enable or entitle
the possessor to receive DigiCipher II television signals. Contact program providers to obtain appropriate
authorizations.
MOTOROLA and the Stylized M Logo are
trademarks or registered trademarks of Motorola
Trademark Holdings, LLC. All other trademarks are
the property of their respective owners.
Dolby Digital is a registered trademark of Dolby
Laboratories. Dolby Digital is manufactured under
license from Dolby Laboratories.
•Do not block any ventilation openings. Install in
accordance with the manufacturer’s
instructions.
•Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
•Unplug this apparatus during lightning storms
or when unused for long periods of time.
•Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as when the power-supply cord or plug is
damaged, liquid has been spilled, or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not
operate normally, or has been dropped.
Damage Requiring Service
Unplug this equipment from the power source,
and contact a qualified service provider if any of
the following situations occurs:
•If the power supply cord or plug is damaged.
•Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding-type plug has two blades
and a third grounding prong. The wide blade or
the third prong is provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
•Protect the power cord from being walked on or
pinched, particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
•Use only attachments and accessories specified
by the manufacturer.
•If liquid or objects have fallen into the unit.
•If the unit became wet from rain or water.
•If the unit was dropped or damaged.
•If the unit’s performance changes.
Service
Do not try to service this product yourself. If you
open or remove the cover, you may be exposed to
dangerous voltage or other hazards and may void
the unit’s warranty. Contact a qualified service
provider for all service.
Page 4
PRECAUCIÓN
PRECAUCIÓN: PARA REDUCIR EL RIESGO DE DESCARGA
ELÉCTRICA, NO RETIRE LA CUBIERTA (O LA TAPA). EN EL
INTERIOR NO H AY PIEZAS QUE SEAN PARA USO DEL USUARIO.
SOLICITE ASISTENCIA TÉCNICA AL PERSONAL DE SERVICIO
CALIFICADO.
RIESGO DE DESCARGA
ELÉCTRICA. NO ABRIR.
ADVERTENCIA
La modificación no autorizada de cualquier unidad, y la venta y el uso
del mismo está prohibida por ley. Cualquier modificación o alteración
de este producto o cualquier recepción no autorizada de programación
de televisión puede someter al usuario y al vendedor, y a la parte que
modifica la unidad a multas, prisión y daños civiles.
NOTA: Este equipo se ha probado y se ha demostrado que cumple con
los límites para un dispositivo digital clase A, según la parte 15 de las
normas de la FCC. Estos límites están diseñados para ofrecer protección
adecuada contra interferencia dañina cuando el equipo se utiliza en un
entorno comercial. Este equipo genera, usa y puede irradiar energía de
radiofrecuencia y, si no se instala y usa de acuerdo con el manual de
instrucciones, puede causar interferencia dañina a las comunicaciones
por radio. Es posible que el funcionamiento de este equipo en un área
residencial cause interferencia dañina, en cuyo caso el usuario deberá
corregir la interferencia y asumir el costo correspondiente. Este aparato
digital no supera los límites de la clase A de emisiones de ruido de radio
del aparato digital establecido en las Normas de interferencia de radio
del Departamento canadiense de comunicaciones.
Reparación y asistencia
Para recibir ayuda sobre devolución o reparación, consulte “Product
Support” en la página 69.
PRECAUCIONES DE OPERACIÓN
ADVERTENCIA: PARA EVITAR RIESGOS DE
INCENDIOS O DESCARGA ELÉCTRICA, NO
EXPONGA ESTE EQUIPO A LA LLUVIA O LA
HUMEDAD.
El símbolo del rayo con cabeza de flecha, dentro de un
triángulo equilátero, está diseñado para alertar al usuario la
presencia de "voltaje peligroso" sin aislamiento dentro del
perímetro del producto que puede tener la magnitud suficiente
para ser un riesgo de descarga eléctrica para las personas.
El signo de exclamación dentro de un triángulo
equilátero está diseñado para alertar al usuario la
presencia de importantes instrucciones de
funcionamiento y mantenimiento (servicio) en la
literatura que acompaña al producto.
Nota para el instalador del sistema CATV
Este recordatorio es para que el instalador del sistema CATV
considere el Artículo 820-40 del Código eléctrico nacional (NEC) que
entrega pautas para una correcta conexión a tierra y, en especial,
especifica que la conexión a tierra del cable debe conectarse al sistema
de conexión a tierra del edificio, lo más cerca posible del punto de
entrada del cable.
Advertencia
Para evitar descargas eléctricas, no use el enchufe eléctrico de la unidad
(polarizado) con un cable de extensión, receptáculo u otra salida a
menos que las aspas queden completamente insertadas para evitar la
exposición de las aspas. El dispositivo de desconexión de la red de
suministro es el enchufe del aparato y debe ser de fácil acceso y estar en
funcionamiento.
La batería de litio no se reemplaza en la instalación para mantener la
vida útil del producto.
General Instrument Corporation comercializa como
Motorola Mobility, Inc.
6450 Sequence Dr.
San Diego, CA 92121
N°. DE DOCUMENTO: 578523-001 REV B, 12/9/10
ATENCIÓN
Esta unidad comercial está diseñada para decodificar señales de televisión DigiCipher
posesión de este dispositivo no permite ni autoriza al dueño
a recibir señales de televisión DigiCipher II. Comuníquese
con los proveedores de programa para obtener las autorizaciones correspondientes.
MOTOROLA y el logotipo de la M estilizada son marcas
comerciales o marcas comerciales registradas de Marcas
Participantes de Motorola LLC. Todas las demás marcas
comerciales son propiedad de sus respectivos dueños.
Dolby Digital es una marca comercial registrada de Dolby
Laboratories. Dolby Digital está fabricado bajo la licencia
de Dolby Laboratories.
•Proteja el cable de alimentación para evitar
pisarlo o que quede apretado, especialmente
en los enchufes y tomas de corriente, y revise
el punto de salida del aparato.
•Considere todas las instrucciones.
•Siga todas las instrucciones.
•No use este aparato cerca del agua.
•Limpie sólo con un paño seco.
•No bloquee las aberturas de ventilación.
Instale siguiendo las instrucciones del
fabricante.
•No instale cerca de fuentes de calor como
radiadores, rejillas de aire caliente, cocinas u
otros aparatos que produzcan calor (incluidos
amplificadores).
•No impida el propósito de seguridad del
enchufe polarizado o con conexión a tierra. Un
enchufe polarizado tiene dos aspas, una más
ancha que la otra. Un enchufe de conexión a
tierra tiene dos aspas y una tercera punta con
conexión a tierra. El aspa ancha o la tercera
punta está diseñada para su seguridad. Si el
enchufe incluido no se ajusta a la salida, pida
al electricista el repuesto de la salida obsoleta.
•Use exclusivamente los accesorios
especificados por el fabricante.
•Desconecte el aparato durante tormentas
eléctricas o cuando no se use durante un
tiempo prolongado.
Daños que requieren servicio de
mantenimiento
Desenchufe este equipo de la fuente de
alimentación y comuníquese con un proveedor de
servicio calificado si se presenta alguna de las
siguientes situaciones:
•Si el cable de alimentación o enchufe está
dañado.
•Si sobre la unidad ha caído líquido o algún
objeto.
•Si la unidad se moja por la lluvia o el agua.
•Si la unidad se golpeó o dañó.
•Si se altera el funcionamiento de la unidad.
Servicio
•Todos los servicios de mantenimiento deben
realizarlos personal calificado. El servicio de
mantenimiento se requiere cuando el aparato
tiene algún daño, por ejemplo cuando el cable
de alimentación o enchufe está dañado, se ha
derramado líquido o el aparato ha sido
golpeado por otros objetos, cuando se ha
expuesto a lluvia o humedad, no funciona
normalmente o se ha caído.
No intente reparar este producto usted mismo. Si
abre o retira la cubierta, es posible que se exponga
a voltaje peligroso u otros daños, y anule la
garantía de la unidad. Para todo tipo de
mantenimiento, comuníquese con un proveedor de
servicio calificado.
Page 6
Page 7
Table of Contents
Chapter 1Introducing the DSR-6100................................................................................................................... 7
Chapter 5Product Support ................................................................................................................................ 69
If You Need Help.......................................................................................................................... 69
Calling for Repairs........................................................................................................................ 69
Chapter 6Downlink/L-Band Frequency Conversion Tables .............................................................................. 71
The Motorola DSR-6100 is a commercial Integrated Receiver Transcoder, designed for broadcasters
and headend operators for receiving digital satellite services. The DSR-6100 unit will process both
high-definition and standard-definition video services. After the DSR-6100 unit is properly configured, it is ready to receive authorization and control information from the satellite operator.
Key Features
•Eight RF inputs
•DC-II QPSK and DVB-S2 demodulation
•DigiCipher-II security
•Gig-E and ASI Outputs with PID Aliasing
•One composite video and one diagnostic video output
•VBI reinsertion for Closed Captioning
•Two stereo pair audio output
•DTMF output
•Three Form-C relays with fault alarm indication
•Uplink controlled retunes
•Memory configuration is saved in nonvolatile memory
•A two-line, 40-character front panel with a Liquid Crystal Display (LCD)
•MPEG-2 HD and/or SD AFD output via uplink authorization
•Web Server GUI for remote operation
DSR-6100 7
Page 14
Page 15
2
123456
TVPass Card
ETHERNET
10 / 100
RF IN
ASI INASI OUT 1
VIDEO OUT OSD VIDEO OUT
8
ASI OUT 2
7
CAUTION: DISCONNECT P OWER CORD BEFORE SERVICI NG
100-240 VAC, 50 / 60 Hz, 1.5A
ASYNC
SECONDARY AUDIO
RELAY 3
PRIMARY AUDIO
RELAY
CONTACT
RATING 1A
30 VDC
RELAY 2
ALARMRELAY 1
L+ L- G R+ R-
L+ L- G R+ R- NO CM NC G NO CM NC
NO CM NC G NO CM NCG Q1+ Q1- G O2+O2-
D+ D- C+ C- G Q3+ Q3-
L-Band RF Input Ports 1 - 8
Ethernet Port
GigE Port
ASI Out
Video Out
OSD Video Out
Relay/Alarm
Primary Audio Out
Secondary Audio Out
Power Connector
Fan UnitFan Unit
ASI In
TV Pass Card
Terminals
Earth Ground
GIGE
AUX VIDEO IN
AUX Video In
Connecting the DSR-6100
Unpacking and Connecting the DSR-6100
Cable connections, described in this chapter, are made to the back panel of the DSR-6100.
Figure 2-1: DSR-6100 Back Panel (Overview)
DSR-61009
Page 16
2
23456
ETHERNET
10 / 100
RF IN
ASI INASI OUT 1
VIDEO OUT
OSD VIDEO OUT
8
ASI OUT 2
7
GIGE
AUX VIDEO IN
SECONDARY AUDIO
RELAY 3
PRIMARY AUDIO
RELAY 2
ALARM
RELAY 1
L+L-GR+R-
L+L-GR+R-NO CM NC G NO CM NC
NO CM NC G NO CM NCGL+L-G R+ R-
D+ D- C+ C- GQ+ Q-
AUX AUDIO IN
ISOCCUE
ASYNC
1
CAUTION: When connecting
any of the eight RF IN ports, the
RF-IN Antenna cable should
only be connected while the
DSR-6100 is properly grounded
and the shield of the coaxial
cable should be earthed in
accordance with Article 820.93
of the NEC, ANSI/NFPA
70:2005 or equivalent.
Unpacking
The shipping carton contains the DSR-6100, quick disconnect terminals, a power cord, and
this Operator Guide.
Figure 2-2: DSR-6100 Back Panel (Detailed)
10
Page 17
Rack Mounting Guidelines
The DSR-6100, with the supplied mounting brackets is designed for installation in an EIA
standard 19-inch (480 mm) equipment rack. Place each DSR-6100 in a stable and level
position within the rack and ensure that all front enclosure screws are tightened to 14 in-lbs.
If multiple DSR-6100s are installed in a rack assembly, the operator may choose to have a
certification agency evaluate the condition of the rack.
Mechanical Loading
The mounting rack location should be secure and level to avoid hazardous instability to the
equipment due to uneven loading or weight distribution within the rack.
Ambient Temperature
When installing the DSR-6100 within a closed or multi-unit rack, the ambient temperature
may be greater than the ambient temperature within the room. Therefore, verify that the
amount of air flow required for safe operation is not compromised (maximum temperature
for the equipment is 40° C). Consideration should be given to the maximum rated ambient
temperature for the DSR-6100’s location when planning for cooling and air circulation. To
evacuate the DSR-6100’s warm air output from within the mounting rack, Motorola
Mobility recommends the use of a fan on top of the rack.
Circuit Overloading
If the DSR-6100 is connected to a power strip, rather than a branch circuit’s direct
connection, use special care to ensure that the unit is properly connected. Always consider
the affect that overloading circuits might have on over-current protection and supply
wiring. To ensure that circuits are not overloaded, read the DSR-6100 UL regulatory power
label on top of the unit. Check all equipment power/amperage ratings to ensure the
mounting rack power rating is not exceeded.
Earth Ground
Reliable earthing of rack-mounted equipment should be maintained. Particular attention
should be given to supply connections other than direct connections to the branch circuit (e.g.
use of power strips). The RF-IN antenna cable should only be connected while the unit is
properly grounded. The shield of the coaxial cable should be earthed in YP accordance with
Article 820.93 of the NEC (National Electrical Code), ANSI/NFPA 70:2005, or equivalent.
Battery Replacement
Do not replace the lithium battery used in the Motorola DSR-6100. Instead, return the
DSR-6100 to a Motorola Mobility authorized service center for replacement with the same
or equivalent type battery as recommended by the manufacturer.
DSR-6100 11
Page 18
2
Connecting the DSR-6100
To connect a DSR-6100 to the GigE signal, see "GigE Usage" on page 23.
To connect a DSR-6100 to an ASI signal, "ASI Usage" on page 23.
To connect a DSR-6100 to an RF signal:
1. Determine which satellite, transponder, Virtual Channel Table (VCT) number, and
Virtual Channel is to be used. Contact the programmer for this system information so
that the desired services can be received.
2. Connect the desired L-Band (satellite antenna LNB or LNB signal splitter) source cable
to RF Input Port 1 through 8, as directed by the programmer.
3. To view video and On-Screen Diagnostics (OSD) during installation, connect the OSD
Video Output on the DSR-6100 to a 75-ohm video monitor or television with
composite video input (standard definition).
Note: The DSR-6100 generates time-specific ad insertion cue tones. The programmer
can include these messages in the encoded signal.
4. If cue tones are needed and made available, connect the differential Cue Tone+, Cue Tone-,
and Ground terminals on the DSR-6100 to the 600-ohm device receiving the tones.
Note: The DSR-6100 provides an alarm relay that can be used to signal an alarm
condition. To indicate an alarm, the DSR-6100 provides a short-circuit electrical
connection between the NC and CM terminals and an open-circuit electrical connection
between the NO and CM terminals. With this configuration, the DSR-6100 is able to
signal an alarm, even for the loss of AC power.
5. Plug the DSR-6100 into a power source. Verify that the LCD screen is lit.
6. Proceed with the installation using the front panel menus.
7. For details on web server GUI, see "Remote Operation" on page 13.
12
Page 19
Remote Operation
The DSR-6100 decoder can be operated remotely from a web browser. When the decoder
is contacted via an HTTP session from a computer, the decoder’s web server responds to
the HTTP session with a login dialog box that requires the user to login with a securitybased user name and password. Once the login is successful, the decoder’s web server then
presents the decoder’s home page to the computer and remote operation can begin.
Some of the IRD configuration settings and control inputs that are accessible through
HTTP include:
•Virtual channel and audio language selection
•Status and device information (e.g., signal strength, alarms, unit address)
•Soft reset
•Settings for acquiring a satellite signal (e.g., transponder frequency, input port)
•Video and audio output customizations
•Alarm triggers
•ASI and Ethernet output customizations
To configure the DSR-6100 for remote operation
1. Contact your network administrator for the IP Subnet Mask address, unique IP address,
and default gateway address to assign to this decoder.
Caution: To use DSR-6100 remote operation, each DSR-6100 on the subnet must be
assigned a unique IP address. Failure to assign a unique IP address to each DSR-6100
on the subnet will result in loss of connectivity with the original IP address conflict.
2. To configure the decoder, use the decoder’s arrow buttons on the front panel to perform
the following procedures:
•10/100 IP Address Menu, page 49
•10/100 Subnet Mask Menu, page 49
•10/100 Default Gateway Menu, page 50
3. Use an RJ-45 cable to connect the decoder’s Ethernet 10/100 port to the subnet that will
be used to operate the decoder remotely.
DSR-6100 13
Page 20
2
http://10.11.23.60
To operate the DSR-6100 remotely
1. Open a browser session, type the decoder’s unique IP address in the address bar, and
press the ENTER key.
For example, if the decoder is configured with IP address 10.11.23.60, then go to the
browser, type: http://10.11.23.60 in the address bar, and press ENTER.
2. When the login dialog box appears (as shown below), enter the User name and Password
and select OK. The default user name is ESPN, and the password is espn.
Note: Web browser login will not be available until commissioned by the uplink.
14
3. When the Home Page appears (as shown below), use the sidebar menu to access the
decoder’s various settings and control features.
.
Page 21
3
Relay 1
Relay 2
Relay 3
Alarm
LCD ScreenAuthorized
Bypass
Signal
Download
Arrow ButtonsENTER Button
DSR-6100
Operating the DSR-6100
All operations described in this chapter require use of the front panel, as shown in Figure 3-1.
Relay 1 - 3Illuminates when relays 1, 2, or 3 are activated.
AlarmIlluminates when the unit enters an alarm state.
AuthorizedIlluminates when the unit is authorized by the service provider.
BypassIlluminates when the unit is in the bypass state.
SignalIlluminates when the unit is locked to a valid carrier.
DownloadIlluminates when the unit has successfully received new firmware and
DSR-610015
Figure 3-1: DSR-6100 Front Panel
is awaiting activation.
Page 22
3
E Setting Setting Setting
Menu Name Label Label Label
Using the Front Panel
The front panel LCD screen displays a series of menus that can be used to
configure and control the system. The name of the current menu is always in the
upper left corner of the screen for easy identification.
•Beneath every menu name are symbols representing key presses that are
possible from the current cursor position in the menu. Note that the available
keypad moves may change during the navigation between menu fields.
•The top row, to the right of the menu name, displays the name of each field
available within that menu. These are called field labels and its setting is
displayed directly below.
•Beneath each label is the current setting for each field.
•Some fields may be changed by the user and others are for display purposes
only. Fields that can be changed have an arrow indicator () just to the left of
the field label. During left/right navigation, the cursor skips over the labels that
cannot be changed.
In addition to the menus on the LCD screen, the LED indicators show the unit’s
current status. The Signal LED is lit when the unit recognizes a valid carrier signal.
A valid carrier signal can be RF input, ASI input, or GigE input. The Authorized
LED is lit when the DigiCipher II signal LED is lit and either (1) the programmer
has transmitted the access messages to allow the unit to decrypt the signal, or (2)
the signal is unencrypted or fixed key.
If the IRD is in an alarm condition, the Alarm LED is lit. See "Alarm Menu" on page
33 for more details.
16
Page 23
Navigating the Menus
Even though the keypad options shown on the LCD screen may change for each
menu and for each field, the control buttons basically do the same thing. The user
may want to practice on a screen to become familiar with how the buttons work.
Notice that:
•Pressing the
(far left corner), causes the cursor to scroll to another menu.
•Pressing the ENTER button while the cursor is blinking next to the menu name
(far left corner) causes the cursor to scroll to the Main, top-level menu.
•Pressing the
move between field labels (or the menu name and a field label). Pressing the
button at the rightmost field label causes the cursor to wrap to the left side
4
of the screen (to the menu name). Likewise, pressing the button when the
cursor is at the menu name causes the cursor to wrap to the rightmost field label.
•When the cursor is blinking on a field label (top row), pressing the ENTER
button causes the cursor to move below the label and enter into the field so the
setting can be changed.
•When the cursor is below the label, the displayed directional controls in the left
corner show what buttons can be pressed to change the setting in that field.
When the symbol is left of the field, this indicates the ability to select from
the available fields. Placing the blinking cursor on those arrows and using those
arrow buttons will reveal each of the available choices for that field, one at a
time. To store changes in a field and move back up to the label line, press the
ENTER button.
buttons while the cursor is blinking next to the menu name
buttons while in the top line of the menu causes the cursor to
4
DSR-6100 17
Page 24
3
Version 0xXXXXX
MOTOROLA DSR-6100
E Install Channel IP Status Diag
DSR-6100
How to Use the Menus
About Menu
The front-panel LCD displays the About menu when the DSR-6100 is initially
plugged in or after a factory reset. This menu identifies the model (MOTOROLA
DSR-6100) and the second line displays the DSR-6100’s actual firmware version
instead of 0xXXXXX, as shown below.
This menu is displayed for 10 seconds, then the front-panel LCD displays the
Main menu.
Main Menu
This menu is the top-level menu and can be navigated to from any other menu by
pressing the ENTER button while the cursor is blinking next to the menu name. This
menu allows the user to select any one of the five main menu groups: Installation
menus, Channel menus, IP menus, Status menus, and Diagnostic menus.
The DSR-6100 allows the user to scroll only to menus that are in the same group.
To scroll to a menu that is in a different menu group, return to the main top-level
menu and select the desired menu group.
18
Page 25
Overview of The LCD Panel Menu Tree
Pressing the ENTER button when the cursor is on a menu name causes the cursor
to return to the main, top level menu. The charts on the following pages show the
menus organized into five main groups: Installation menus, Channel selection
menus, IP menus, Status menus, and Diagnostic menus.
DSR-6100 19
Page 26
3
20
Page 27
Diagnostic Menus
E Off
DIAGNOSTIC MENUS
UNIT ADDRESS
E ddd-ddddd-ddddd-ddd
E Not Inserted
TV PASS CARD Status
E Off Off
AUDIO TEST SIGNAL L1/R1 L2/R2
E Off
VIDEO TEST SIGNAL Pattern
E Off Off
AD INSERTION TEST Cue Tone Relay
DSR-6100 21
Page 28
3
E Port 1 Xpndr 01 1430.00
MANUAL TUNE Input Mode Xpndr LFreq
E ASI In
MANUAL TUNE Input
E GigE In 255.255.255.255
MANUAL TUNE Input Multicast Address
To specify an RF input port, see
"RF Usage" on page 24.
To specify the ASI In as the input port,
see "ASI Usage" on page 23.
To specify the GigE In as the input port,
see "GigE Usage" on page 23.
Installation Menus
The purpose of the installation menus is to configure the ports and choose settings
that remain fixed over time. This section describes in detail each of the Installation
menus, fields, and options displayed on the LCD panel.
Return to the main top-level menu and then select the installation menu group.
With the blinking cursor at the upper left, press ENTER button to return to the main
top-level menu. Press the
the ENTER button. The DSR-6100 displays the previously selected sub-menu.
Manual Tune Menu
Use this menu to begin to acquire a DigiCipher II system signal, by selecting a
transponder frequency for one of the eight L-Band inputs. In addition, this menu
allows a user to select the ASI input or GigE input, as an alternative to RF ports 1
through 8.
buttons until the cursor is at the Install label, and press
4
22
Page 29
ASI Usage
Input Field
Use this section to specify the ASI input port. The Input field displays the active
input. Press the4 button until the cursor is at the Input label and press the ENTER
button. Press the
selection and return to the top line of the menu.
The following screen prompts the user to confirm the selection and exit the field.
buttons to scroll to ASI In. Press ENTER to confirm the
If you press any arrow button (
disappears and the MANUAL TUNE menu reappears without any changes. To set
the port selection, press the ENTER button.
Skip to page 30 to set the remaining installation fields.
GigE Usage
Input Field
Use this section to specify the GigE input port. The Input field displays the active
input. Press the4 button until the cursor is at the Input label and press the ENTER
button. Press the
selection and return to the top line of the menu.
The following screen prompts the user to confirm the selection and exit the field.
4
buttons to scroll to GigE In. Press ENTER to confirm the
) at this point, the Caution screen
If you press any arrow button (
disappears and the MANUAL TUNE menu reappears without any changes. To set
the port selection, press the ENTER button.
DSR-6100 23
4
) at this point, the Caution screen
Page 30
3
GigE Input IP Addr FieldDefault: 239.001.001.001
Use the following procedure to set and view the Input GigE IP address on the back
panel of the DSR-6100. Press the
buttons until the GigE Input IP Addr menu
appears. Use this menu to enter an IP address for the Ethernet port. The address is
represented in the common dotted-decimal format. Contact the network
administrator for details about configuring the Ethernet port for operation on your
local network.
Important: Do not configure the IP Address of the 10/100 and GigE to be on the
same subnet.
Press the 4 button until the cursor is at the IP Address label, and press the ENTER
button to move into the field. Use the arrow buttons (
4
) to enter the desired
address and then press ENTER to confirm the selection and exit the field.
Skip to page 30 to set the remaining installation fields.
RF Usage
Use this section to select one of the eight RF input ports so that the DSR-6100 can
acquire the DigiCipher II system signal and automatically download network data
required for operation.
Because many satellite broadcasters use standard C-band transponder center
frequencies, selecting a transponder number is the default tuning mode. Use the
Xpndr option in the Mode field and edit the Xpndr (transponder) field (described
on page 26), for tuning such signals.
For offset-frequency C-band, fractional transponders, or Ku-band satellite
broadcasts, use the LFreq field in the Mode field (described on page 26), and
directly edit the L-band frequency field.
The DSR-6100 does not actually require any distinction between C-band and Kuband satellite signals in order to tune and acquire a compatible signal. However,
correct modulation information is necessary. For details on modulation, see
“Modulation Menu” on page 27.
24
Page 31
Input FieldDefault: Port 1
Press E to continue or to stop
CAUTION: Service will be interrupted
The Input field displays the active input. To select the input:
Press the4 button until the cursor is at the Input label and press the ENTER button.
Press the
buttons to scroll to the input that is connected. Unless changed, the
DSR-6100 displays Port 1. Press ENTER to confirm the selection and return to the top
line of the menu. If Port 1 through Port 8 is selected, then use the arrow buttons
(
4
) to specify the other fields (Mode field, Xpndr field, and Lfreq field) as
needed. These three fields are not visible when ASI In or GigE In is selected.
The following screen prompts the user to confirm the selection and exit the field.
If you press any arrow button (
4
) at this point, the Caution screen
disappears and the MANUAL TUNE menu reappears without any changes. To set
the port selection, press the ENTER button.
Mode FieldDefault: Xpndr
The Mode field allows selection of the frequency plan type for the satellite signal to
which the DSR-6100 is tuned. If the application is a North American C-band
satellite center frequency, select the transponder number in the Xpndr field.
Otherwise, set this field to LFreq and also set the new field (LFreq) as described
below. The L Freq option can be used for current satellite LNB signals, including
C-band and Ku-band.
Press the4button until the cursor is on the Mode label. Then press the ENTER
button to move into the field. There are two choices: Xpndr and L Freq. Press the
buttons to display the desired choice. Then press the ENTER button to
confirm the selection and exit the field.
If Xpndr is selected, choose a transponder in the Xpndr field. The frequency in the
LFreq field is set automatically and cannot be edited.
If L Freq is selected, the Xpndr field no longer appears because the transponder/
frequency relationship is not known. Select a transponder frequency between 950
and 2150 MHz in the LFreq field. This field is not available when Input field is set
to either ASI In or GigE In.
DSR-6100 25
Page 32
3
Xpndr Field
This field is not available when Input field is set to either ASI In or GigE In. This
field is not available when the Mode field is set to LFreq.
This field allows selection of an initial satellite transponder number and can only
be used if the Xpndr option in the Mode field is selected. The Xpndr field cannot be
edited if L Freq in the Mode field is selected. Press the 4 button until the cursor is
at the Xpndr label. Then press the ENTER button to move into the field.
Then press the
associated transponder/frequency tables are stored in the DSR-6100, scroll through
the transponder numbers and notice that the associated frequency (shown in the
LFreq field to the right) automatically changed with the selection (970-1430 MHz).
There are 24 transponder options, and when the desired transponder selection is
displayed, press the ENTER button to confirm selection and move the cursor back
up to the field label.
LFreq Field
This field is not available when Input field is set to either ASI In or GigE In. If the
Mode field is set to Xpndr, this field is set automatically and cannot be edited.
If the LFreq option in the Mode field is chosen, use this field, to directly tune the
frequency. Press the4 button until the cursor is at the LFreq label. Then press the
ENTER button to move into the field.
Use the arrow buttons (
frequency between 950 MHz and 2150 MHz and press the ENTER button to
confirm the selection and move the cursor back up to the field label.
For those satellite carriers which are offset (C-band or Ku-Band), use the L Freq
option to enter the exact center frequency of a carrier, rather than using a nearbybut-not-exact C-band transponder center frequency. Long-term frequency tracking
is best if the user enters a precise carrier center frequency.
buttons to select the desired transponder number. Since the
4
) to select the desired frequency. Select a
Contact the programmer or network operator for details about the satellite, transponder, and frequencies being used. If one frequency is identified as the root transponder,
using this frequency may expedite the download process during installation.
26
Page 33
Modulation Menu
E DCII-AUTO
MODULATION Mode
E DVBS2 30.000000
MODULATION Mode Symbol
E DCII-MAN 19.51 3/4 Comb
MODULATION Mode Sym Code Format
This menu is not available when the Manual Tune menu has the Input field set to
ASI In or GigE In. That option is described on page 25.
This menu, together with the Manual Tune menu, allows the user to initially
acquire a DigiCipher II signal. Press the
menu appears. Press the ENTER button to continue.
When the DCII-MAN option is selected, the user must additionally specify a
Symbol/Code/Format combination. When the Mode field is set to DVBS2, the user
must additionally specify a Symbol Rate (Msps).
buttons until the MODULATION
Note: DVB-MAN and 8PSK-TC are not supported and should not be used.
Mode FieldDefault: DCII-AUTO
Press the4button until the cursor is at the Mode label, and press the ENTER button
to move into the field. Press the
DCII-MAN, or DVBS2. Select a mode and press ENTER to exit the field.
Note: In order to receive a DVB-S2 modulated carrier, the DSR-6100 must be set to
DVBS2 mode, and the correct Symbol Rate (Msps) must be entered in the Symbol
field. In DCII-MAN mode, the correct Symbol Rate (Msps) must be entered in the
Symbol field, Code field, and Format field. If DCII-AUTO is selected, the DSR-6100
searches through all available DC-II Symbol/Code/Format combinations to acquire
a signal and then remains locked on that signal.
Symbol / Code / Format FieldsDefault: 19.51 3/4 Comb
This field is not available when the Mode field is set to DCII-AUTO. If the Mode field
is set to DCII-MAN, press the 4 button until the cursor is at the Symb label and press
the ENTER button to move into the field. Use the
Symbol/Code/Format combinations. Select the combination provided by your
programmer and press ENTER to confirm and exit the field.
If the Mode field is set to DVBS2, the Symbol field can be edited to any value up to
33.000000 by using the
DSR-6100 27
buttons.
buttons to display the options: DCII-AUTO,
buttons to scroll through the
Page 34
3
E 1 Auto ------
PORT ID Mode Sat Polar
Port Menu
Use this menu to configure RF In ports (Port 1 through Port 8). This menu is not
available when the Manual Tune menu has the Input field set to ASI In or GigE In.
That option is described on page 25.
Because the DSR-6100 has eight RF input ports that can potentially be used to
switch and tune signals from multiple satellite antenna, the DSR-6100 demands
there be an accurate association of the port with the Satellite and Polarity
designators programmed in the Uplink encoder system(s) to which we plan to
downlink from on each port.
Because accuracy is critical, a default Auto mode automatically updates the Sat (Satellite) and Polar (Polarity) fields for the one port that is currently being tuned. This automatic population of the fields occurs upon entry of acceptable channel information.
To ensure success in getting initial authorization, decryption, and output, leave this
menu unchanged in Auto mode (as shown below).
If the Uplink Signal Provider gives detailed instructions, set the Mode field to
Manual and set the Sat (Satellite) field and Polar (Polarity) field. Any mismatch
between what is entered into these fields and the Uplink encoder Satellite and
Polarity designations for the services will prevent authorization decryption and
service output. Satellite names and polarity designators for a given service do not
necessarily reflect actual satellite names or even the correct polarity of the actual
signal. These values are set within the provider’s encoder system.
ID FieldDefault: 1
Use this field to choose which port to configure (1 through 8). Press the 4 button
until the cursor is at the ID field, press the ENTER button to move into the field,
use the
buttons to choose a port and press the ENTER button to confirm the
selection and exit the field.
Mode FieldDefault: Auto
Use the Mode field to select the mode for port setup. Press the 4 button until the
cursor is at the Mode label, and press the ENTER button to move into the field.
Press the
buttons to choose the desired mode (either AUTO and MANUAL)
and press the ENTER button to confirm the selection and exit the field.
28
Page 35
Sat FieldDefault: ---
E Off
PORT CONFIG Port 1 Power
If the Mode field is set to Manual, use this field to select a satellite name for the
designated port. This field is not editable when the Mode field is set to Auto.
Press the4 button until the cursor is at the Sat label. Press the ENTER button to
move into the field. Use the
changed. Then use the
buttons to select the character position to be
4
buttons to scroll through the character choices and
press the ENTER button to confirm selection and exit the field.
This field displays dashes (---) when the port is not related to a satellite.
Polar FieldDefault: ---
If the Mode field is set to Manual, use this field to select a polarity for the designated
port. Press the 4 button until the cursor is at the Polar label. Press the ENTER button
to move into the field and press the
buttons to display the options: H/LHP
(Horizontal/Left-Hand Polarity) or V/RHP (Vertical/Right-Hand Polarity). Select a
polarity and press ENTER button to confirm the selection and exit the field.
Port Config Menu
Use this menu to configure Low Noise Block (LNB) power for RF In Port 1. This
menus is not available when Input field is set to either ASI In or GigE In
Port1 Power FieldDefault: OFF
Use this field to direct power to the external Low Noise Block (LNB). Press the 4
button until the cursor is at the Port 1 Power label, and press the ENTER button to
move into the field. Press the
When the ON option is selected, the DSR-DSR-6100 supplies 16-22 VDC on the
RF In Port 1 antenna input connector, as shown in Figure 2-2 on page 10.
DSR-6100 29
buttons to display the options: OFF and ON.
Page 36
3
E On Stereo Moderate
AUDIO1 DialNorm AudioMix Compress
E On Stereo Moderate
AUDIO2 DialNorm AudioMix Compress
Press E to continue or to stop
CAUTION: Check audio language selection
Audio1 and Audio2 Menus
Use these menus to customize the audio output. Press the
Audio1 or Audio2 menu appears (shown below).
DialNorm FieldDefault: On
The DialNorm field allows the user to normalize speech levels to a constant level
over all channels—raising or lowering the volume of the dialogue to a level that is
appropriate for the background sound track.
Press the 4 button until the cursor is at the DialNorm label. Press the ENTER button
to move into the field. There are two options, On and Off. Press the
change the setting. Press ENTER to confirm the selection and exit the field.
AudioMix FieldDefault: Stereo
Note: If the audio input mode is stereo and you are connecting to a mono
modulator, you must set this field to Mono.
buttons until the
buttons to
This field allows selection of the audio processing options. Press the 4 button until
the cursor is at the AudioMix label, and press the ENTER button to move into the
field. Press the
•StereoStereo output on both left and right channel
•SurroundEnhanced stereo with surround pass-through
•MonoMono output on left channel
•Dual Mono Mono output on both left and right channels
Caution: If Dual Mono is selected, a caution screen appears. If Dual Mono is selected
and then changed to another option, the caution screen appears again.
This caution message denotes possible conflicts between this menu and the
language selection menus that could mute the audio. By pressing the ENTER
button (ignoring the caution), the DSR-6100 changes to Dual Mono, and uses the
language previously selected for Mono (or Stereo) for both left and right channels.
30
buttons to display the options:
Page 37
To select a single language for Mono, Dual Mono, or Stereo output, see
"AUD1LANG and AUD2LANG Menus" on page 44.
Compress FieldDefault: Moderate
This field allows control of the degree of audio level compression. Press the 4
button until the cursor is at the Compress label, and press the ENTER button to
move into the field. Press the
buttons to display the options:
•HeavyReduces the louder audio signals and boosts the softer signals
using tighter compression thresholds in order to eliminate
dramatic fluctuations in the audio signal level and suppress
dynamic range of the audio signal.
•ModerateProvides some reduction and amplification of the audio signal, but
the thresholds are wider apart, providing moderate dynamic range
of the audio signal.
•OffCompression is not used and provides full dynamic range of the
audio signal.
Press the ENTER button to confirm the selection and exit the field.
DSR-6100 31
Page 38
3
E Joint +00 +00
AUDIO1 GAIN Mode Left Right
E Joint +00 +00
AUDIO2 GAIN Mode Left Right
Audio1 and Audio2 Gain Menus
These menus allow adjustment of the audio signal output level from +00 to -20 dB,
in 1 dB increments. Press the
AUDIO1 GAIN or AUDIO2 GAIN).
The user may adjust the output levels of the left and right channels jointly. The
output level of the right channel tracks the setting for the left channel when the
output levels are adjusted jointly.
buttons until the desired menu appears (either
Mode FieldDefault: Joint
Note: The Mode field is not editable.
This field is associated with the Audio Gain port and is always set to Joint. This
means, both channels are configured jointly using the Left field settings as the control
for both audio channels.
Left and Right FieldsDefault: +00
Note: The Right field is not editable.
The Left field allows adjustment of the output level of the Left and Right audio
signals. Press the 4 button until the cursor is at the Left label, and press the
ENTER button to move into the field. Use the
adjust the output level for the Left and Right audio signals from +00 to -20 dB, in
1 dB increments.
Press the ENTER button to confirm the selections.
buttons to simultaneously
32
Page 39
Alarm Menu
This menu allows the user to set up different bypass modes in case the DSR-6100
goes into an alarm condition. Press the button until the Alarm menu is located
(shown below).
The alarm can be activated for any of the following conditions:
•The DSR-6100’s tuner loses lock when the input is RF.
•The DSR-6100 cannot lock to the ASI input when the input is ASI.
•The DSR-6100 is unable to render video.
•The DSR-6100 is not authorized to access the selected service.
•The DSR-6100 loses power.
•The DSR-6100 GigE Port Link state is inactive when the Input field
(described on page 25) is set to GigE In.
Trigger FieldDefault: Auto
The Trigger field allows the user to select the trigger condition to activate an alarm
on the IRD. When the alarm is activated, the Alarm LED illuminates and the alarm
relay indicates an alarm condition.
Press the 4 button until the cursor is at the Trigger label, and press the ENTER
button to move into the field. Press the
buttons to display the five options:
•DisabledDisables any trigger for an IRD alarm.
•AutoEnables all triggers for an IRD alarm.
•No SignalAlarm is triggered when the IRD loses the
incoming signal.
•No VideoAlarm is triggered when the IRD loses video input.
•No Auth (Authorization)Alarm is triggered when the IRD is not authorized
to access a selected service.
Press the ENTER button to select the option shown and exit the field.
DSR-6100 33
Page 40
3
Bypass FieldDefault: Disabled
Press the 4 button until the cursor is at the Bypass label, and press the ENTER
button to move into the field. Press the
buttons to display the options:
•BypassedThe Bypass mode is activated and the DSR-6100 loops through
the auxiliary video and audio inputs regardless of DigiCipher II
system service authorization status. The Bypass LED on the front
panel is always lit when the DSR-6100 is in the bypass state.
•DisabledThe DSR-6100 ignores the auxiliary inputs for video and audio
and attempts to output the satellite data, regardless of
authorization status.
•AlarmThe DSR-6100 automatically switches to the bypassed state if
it enters the alarm condition. At such time, the Aux Video and
Audio inputs are routed to the IRD output, and the front panel
Bypass LED is lit. When the DSR-6100 exits the alarm
condition, the unit switches back to satellite video and audio.
Press the ENTER button to select the option shown and exit the field.
Test FieldDefault: Off
Note: The Test field returns to the default value (Off) when the field is exited.
The Test field provides an IRD alarm test when this field is set to On. Press the
buttons to display the two options: Off or On.
Caution: Selecting the alarm test function with the Bypass Field set to Alarm
causes the satellite Video and Audio to be bypassed. This may result in a service
outage when the analog video and audio outputs to the cable plant.
Press the ENTER button to select the option shown and exit the field.
34
Page 41
ASI Output Menu
E On Packet On
ASI OUTPUT Enable Format Pid Alias
Press the
buttons until the ASI Output menu appears. Use this menu to
configure the digital ASI output. It is used to define the format of the ASI output
and to enable PID aliasing.
Note: The DSR-6100 provides two ASI outputs:
ASI#1: The DSR-6100 has the ability to output an MPEG-4 transport multiplex
stream at a data rate of either 54 Mbps or 81 Mbps, depending on whether PID
aliasing is enabled or not. When PID aliasing is enabled, the DSR-6100 outputs an
MPEG-4 transport stream that contains only one MPEG program and at a data
rate of 54 Mbps; that program is identified as MPEG Program #1 and the PIDs for
the constituent components are remapped to a consistent set, as described in Tables
3-1 and 3-2 on page 36. This MPEG program corresponds to the program content
that is available at the analog video and audio outputs (the monitored program).
Otherwise, when PID aliasing is disabled, the DSR-6100 outputs an MPEG
transport stream at a data rate of 81 Mbps, which contains all of the MPEG
programs that the DSR-6100 receives from the uplink.
ASI#2: The DSR-6100 also has the ability to convert the incoming MPEG-4
program to both an MPEG-2 HD (High Definition) Program and a MEPG-2 SD
(Standard Definition) Program. Both the HD and the SD programs are carried in
the same transport stream and at a data rate of 54 Mbps. The SD program is
identified as MPEG program #1 and the HD Program is identified as MPEG
Program #2. The PIDs are identified in Tables 3-1 and 3-2 on page 36.
DSR-6100 35
Page 42
3
Table 3-1: DSR-6100 Transport Stream Outputs
Unit Configuration
PhaseInput
1MPEG-2Off(Same as input)(Same as input)(Same as input)(N/A)
1MPEG-2OnProgram 1
2MPEG-2Off(Same as input)(Same as input)(Same as input)(N/A)
2MPEG-2OnProgram 1
Video PID:1E00
Audio #1 PID: 1020
Audio #2 PID: 1021
Program 1
Video PID:1E00
Audio #1 PID: 1020
Audio #2 PID: 1021
Outputs (Additional PID assignments are designated in Table 3-2)
ASI 1ASI 2
Program 1
Video PID: 1E00
Audio #1 PID: 1020
Audio #2 PID: 1021
Program 1
Video PID: 1E00
Audio #1 PID: 1020
Audio #2 PID: 1021
SD Program 1
Video PID: 1E00
Audio #1 PID: 1020
Audio #2 PID: 1021
HD Program 2
Video PID: 0801
Audio #1 PID: 0802
Audio #2 PID: 0803
SD Program 1
Video PID: 1E00
Audio #1 PID: 1020
Audio #2 PID: 1021
HD Program 2
Video PID:0801
Audio #1 PID: 0802
Audio #2 PID: 0803
Program 1
Video PID:1E00
Audio #1 PID: 1020
Audio #2 PID: 1021
Program 1
Video PID:1E00
Audio #1 PID: 1020
Audio #2 PID: 1021
Program 1
Video PID:1E00
Audio #1 PID: 1020
Audio #2 PID: 1021
Program 1
Video PID:1E00
Audio #1 PID: 1020
Audio #2 PID: 1021
GigE
Pass Through
(Same as input)
(Same as input)
SD Program 1
Video PID:1E00
Audio #1 PID: 1020
Audio #2 PID: 1021
HD Program 2
Video PID:0801
Audio #1 PID: 0802
Audio #2 PID: 0803
SD Program 1
Video PID:1E00
Audio #1 PID: 1020
Audio #2 PID: 1021
HD Program 2
Video PID:0801
Audio #1 PID: 0802
Audio #2 PID: 0803
GigE
Transcoded
(N/A)
(N/A)
Table 3-2: Additional DSR-6100 Output PIDs
Component
PAT0x00000x0000(N/A)
Network0x1A000x1A00(N/A)
PMT0x1C000x0800(N/A)
Video0x1E000x0801(N/A)
Audio0x1020+I0x0802+i(N/A)
DPI0x10C0+i0x0815+i(N/A)
DSMCC0x01A0+i0x081C+iASI#1 has no Program 2. For ASI #2, DSMCC data is not included in Program 1 or
Subtitles0x1040+i(See Note) Subtitles are not supported by the DSR-6100. However, if they are carried in the
ISOC
data
ASYNC
data
Others 0x1025
Program 1
PIDs
0x1840(See Note) ASI#1 has no Program 2. For ASI #2, ISOC data is not included in Program 1 or
0x1860(See Note) ASI#1 has no Program 2. For ASI #2, ASYNC data is not included in Program 1 or
to
0x103F
Program 2
PIDs
0x0825
to
0x083F
Notes
Program 2.
input, the DSR-6100 will pass through subtitles in Program 2 using the PIDs from
the unanticipated component PID pool (described below).
Program 2.
Program 2.
Other component types that are unanticipated (i.e., unknown at this time) are
aliased to a PID value from the specified pool that is reserved for unanticipated
components. EBIF is considered deemed unanticipated because no generallyaccepted component type has been allocated for EBIF components.
36
Page 43
Enable FieldDefault: On
E No
RESET Reset Type
Press E to continue or to stop
CAUTION: IRD memory will be reset
Note: The ASI output can be disabled by control information from the Uplink
Programmer (Broadcast Network Controller [BNC]).
When ASI output is disabled by the BNC, this field is not editable and displays Lock
Off. Otherwise, if the BNC enables the ASI output, this field is editable with the
default value (On). Press the
Format FieldDefault: Packet
buttons to display the options (On and Off).
When PID Alias is set to On, use this field to specify the transport stream packet
structure either as a burst of contiguous bytes (Packet), or as individual bytes (Byte).
Pid Alias FieldDefault: On
When this field is set On, the DSR-6100 remaps all PIDs to a constantly-set of values
and incorporates the remapped value in the output transport stream. When the Uplink
Programmer enforces PID aliasing, the PID Alias field displays Lock On and
becomes uneditable.
Reset Menu
Press the
buttons until the Reset menu appears. Use this menu to execute
factory defaults and perform power cycle resets.
Reset Type FieldDefault: No
Press the 4 button until the cursor is at the Reset Type label, and press the ENTER
button to move into the field. Press the
buttons to display the options: No,
Factory Defaults, or Power Cycle.
Factory Defaults Option
Use the Factory Defaults option to reset the system to the programming values
originally set by the factory firmware.
CAUTION: Selecting this reset option deletes all defined setups and downloaded
information. This operation interrupts service output, so use it carefully.
Press the ENTER button. The following caution message appears and indicates that
all programming will be lost if the action proceeds.
DSR-6100 37
Page 44
3
Factory Default reset in progress..
Press E to continue or to stop
CAUTION: Reset will interrupt service
Press E to continue or tostop
Power Cycle reset in progress. . .
Press E to continue or to stop
Power Cycle reset in progress. . .
E 18
CORE Contrast
Press any arrow button (
Otherwise, press the ENTER button to proceed. The following message displays.
Power Cycle Option
The Power Cycle option reboots the DSR-6100 without losing internal user setup
information or downloaded network information. Pressing the ENTER button
causes the following caution message to appear.
Press any arrow button (
or press the ENTER button to proceed. The following message displays:
4
4
) to back out of the field and leave it unchanged.
) to back out of the field and leave it unchanged,
Core Menu
Press the
front panel LCD contrast.
Contrast FieldDefault: 18
To adjust the LCD contrast, press the 4 button until the cursor is at the Contrast
label, and press the ENTER button to move into the field. Use the arrow buttons
(
) to select a value between 0 and 30, with 0 representing the least contrast and
30 the most. Adjust the contrast so that the LCD panel can be read clearly. Press the
ENTER button to confirm the selection and exit the field.
buttons until the Core menu appears. Use this menu to change the
38
Page 45
Video Out Menu
VIDEO OUT 525
E NTSC
Press E to continue or to stop
CAUTION: Change will interrupt service
FIRMWARE Boot:FPGA:High Upgrade
E XXXXXX:XXXXXX:XXXXX 000000
Press the
buttons until the VIDEO OUT menu appears. Use this menu to modify the
video output format. When the input to the uplink encoder is 525-line, the field here selects
the unit output, either NTSC or PAL-M.
525 FieldDefault: NTSC
Press the 4 button until the cursor is at the 525 label, and press the ENTER button
to move into the field. This field allows selection of the output format for 525-line
video as either NTSC or PAL-M. Use the
buttons to specify the desired option
and press the ENTER button to confirm the selection. Pressing the ENTER button
causes the following caution message to appear.
Press any arrow button (
4
) to back out of the field and leave it unchanged,
or press the ENTER button to proceed.
Firmware Menu
Press the
DSR-6100's firmware release information, which is equivalent to the product
version number. This menu cannot be changed, but since the firmware is
periodically updated, this menu confirms that the update was successful. This menu
is used most commonly in troubleshooting. The High version value (shown below)
is the current firmware version.
Boot:FPGA:High Field
This field displays the version of boot, FPGA, and the high code. The boot code is
loaded at the factory. The FPGA and high codes may be upgraded to later versions
by a download that is delivered over the satellite signal from either the L-band or
ASI input. The code versions are represented by a six-digit hexadecimal number.
This field is non-editable.
DSR-6100 39
buttons until the Firmware menu appears. This menu displays the
Page 46
3
DOWNLOAD File Current Rcvd Total
E 00 of 00 0000 0000 0000
Upgrade Field
The Upgrade field displays the version of the upgrade code that is available. This
field displays 000000 when no upgrade code is available. Available upgrades are
installed the next time the DSR-6100 is rebooted. This field is non-editable.
Download Menu
Press the
monitor the status of the current code download. This menu is used most
commonly in troubleshooting.
During a background code download, the DSR-6100 collects the upgrade code in the
background while concurrently decoding video and audio services. This menu may
be selected anytime before, during, and after a background code download.
File Field
The File field consists of two sub-fields. The first sub-field is editable and selects,
by index, a download file for monitoring. The second sub-field is non-editable and
indicates the total number of files that have been downloaded and/or are available
to be downloaded.
Current Field
This non-editable field pertains to the file selected in the File field and indicates the
ID for the current segment received by the DSR-6100 during the download of the file.
buttons until the DOWNLOAD menu appears. Use this menu to
Rcvd Field
This non-editable field indicates the number of segments that the DSR-6100 has
received for the file selected in the File field.
Total Field
This non-editable field displays the ID for the last segment of the file selected in the
File field.
40
Page 47
Channel Menus
E 00000 0000 (Not in map)
CHANNEL VCT Channel Xpndr
Channel Menu
Press the
active VCT, select the Virtual Channel, and view the name of the current transponder.
VCT Field
Use this field to select a Virtual Channel Table (VCT) number. Contact the program
provider for the correct VCT number to enter for that encoder system. Press the 4
button until the cursor is at the VCT label, and press the ENTER button to move
into the field. While ensuring that the cursor remains on the up/down symbol ( ),
press the
four VCTs, then only four VCTs appear in this field.) Press the ENTER button to
confirm the selection and exit the field.
This field also provides a second method for selecting the VCT. To do this, use the
4
press the
applicable digit. Press the ENTER button to confirm the selection and exit the field.
Channel Field
buttons until the Channel menu appears. Use this menu to select an
buttons to scroll throughout the available VCTs. (If the network has
buttons to select the digit to change and then, while the cursor is on that digit,
buttons to display the required value. Repeat this process for each
Use the Channel field to select the Virtual Channel for the output service. The DSR6100 supports channel values from 0000 to 4095. Press the 4 button until the cursor
is at the Channel label, and press the ENTER button to move into the field. While
ensuring that the cursor remains on the up/down symbol ( ), press the
to scroll through the available Virtual Channels. (If the chosen VCT contains twentyfour Virtual Channels, then only twenty-four Virtual Channels appear in this field.)
Press the ENTER button to confirm the selection and exit the field.
This field also provides a second method for selecting the Virtual Channel. To do
this, use the
on that digit, press the
process for each applicable digit. Press the ENTER button to confirm the selection
and exit the field.
DSR-6100 41
buttons to select the digit to change and then, while the cursor is
4
buttons to display the required value. Repeat this
buttons
Page 48
3
Press E to continue or to stop
CAUTION: Changing to DCII selection mode
E 00000 0000 (Not in map)
CHANNEL VCT Channel Xpndr
Press E to continue or to stop
CAUTION: Channel dddd not present
The DSR-6100 displays caution messages for the following conditions:
•A caution message is displayed when changing from an MPEG program
number selection to a Virtual Channel.
Press any arrow button (
4
) to back out of the field and leave it
unchanged. Otherwise, press the ENTER button to proceed.
•If a Virtual Channel is selected that is not in the chosen VCT, then a warning
message, “Not in map” is displayed to the right of the Virtual Channel.
•Virtual Channels identify satellite and polarity attributes. The RF input ports
are set up with satellite and polarity attributes. For more details, see "Port
Menu" on page 28. The DSR-6100 uses these satellite and polarity attributes to
determine which RF port to use. However, if a Virtual Channel is selected that
does not match the satellite and polarity attributes of either port, then the DSR6100 is unable to determine which port to use and the following caution
message is displayed.
Press any arrow button (
4
) to back out of the field and leave it unchanged.
Otherwise, press the ENTER button to proceed.
Note: The DSR-6100 cannot decode the chosen Virtual Channel until a port is set
up with the applicable satellite and polarity information.
Xpndr Field
This non-editable field displays the current (Xpndr) transponder name (alpha/
numeric) that is downloaded. If a Virtual Channel is selected that is not in the chosen
VCT, then a warning message, (Not in map) is displayed to the right of the Virtual
Channel. This field serves as a label or identifier for the signal source. For more
details, see "Port Menu" on page 28.
42
Page 49
MPEG SELECT Menu
E 00000
MPEG SELECT Program
Press E to continue or to stop
CAUTION: Changing to MPEG selection mode
Press E to continue or to stop
CAUTION: Program ddddd does not exist
Use this menu to select which service is displayed at the video and audio outputs by
specifying the MPEG program number. Press the
SELECT menu appears. The MPEG program number can be used instead of a
Virtual Channel, but only if the DSR-6100 is already tuned to the appropriate
L-band or ASI input signal.
Program FieldDefault: 00000
Press the4button until the cursor is at the Program label, and press the ENTER
button to move into the field. While ensuring that the cursor remains on the up/
down symbol ( ), press the
programs. (If the current L-band or ASI input signal contains four MPEG
programs, then only four MPEG programs appear in this field.) Press the ENTER
button to confirm the selection and exit the field.
This field also provides a second method for selecting the MPEG program. Use the
buttons to select the digit to change and then, while the cursor is on that digit,
4
press the
buttons to display the required value. Repeat this process for each
applicable digit. Press the ENTER button to confirm the selection and exit the field.
buttons to scroll throughout the available MPEG
buttons until the MPEG
The DSR-6100 displays caution messages for the following conditions:
•A caution message is displayed when changing from a Virtual Channel to a
MPEG program number. Press any arrow button (
4
) to back out of the
field and leave it unchanged. Otherwise, press the ENTER button to proceed.
•A caution message displays when an MPEG program number is selected which
does not exist.
Press any arrow button (
4
) to back out of the field and leave it
unchanged. Otherwise, press the ENTER button to proceed.
DSR-6100 43
Page 50
3
E All def def ---
AUD1LANG Dspl Left Right InputMode
AUD2LANG Dspl Left Right InputMode
E All def def ---
AUD1LANG and AUD2LANG Menus
These menus (Audio1 and Audio2 Language) have three fields to modify and view
the status of the language for the Audio1 and Audio2 outputs. Also, use this menu
to view the mode of the audio signal as it is received from the programmer and
before any subsequent down mixing that the DSR-6100 may perform. Press the
buttons until the desired menu appears (either AUD1LANG or AUD2LANG).
Note: If the Left and Right field have a language followed by a two-digit value (00
to 99), this indicates the specified language, followed by the dialect. For example,
use Eng13 for the 13th version of English. Use this feature for languages with
multiple dialects.
Dspl FieldDefault: All
Press the 4 button until the cursor is at the Dspl (Display) label, and press the
ENTER button to move into the field. Select the option that applies to the Left and
Right. There are three options: All, Avail, and Status. Press the
specify the desired option.
•AllUse the arrow button (
•AvailUse the Available option to scroll through the languages supported
•StatusUse the Status option to view the actual audio language. The
44
buttons to
4
) to enter the three-letter code in
the Left field. It may be necessary to select languages that are not
functional at this time, but will be functional in the future. Press
the ENTER button to confirm the selection and exit the field.
by the system while the cursor is in the Left and Right fields.
Furthermore, use this option to scroll through only the languages
available for the active service. (If the active service has only
three languages, as listed for the Virtual Channel or program, only
three appear. If the user changes the service, the number of
languages may also change.) Press the ENTER button to confirm
the selection and exit the field.
actual language can differ from the chosen language. This may
occur when the user’s choice for language is unavailable. The
bullets in the next topic describe the rules that govern which
language is used.
Page 51
Left and Right Fields
Press the 4 button until the cursor is at the Left label, and press the ENTER button to
move into the field. If the Dspl field is set to All and the AudioMix field (described on
page page 30) is set to Dual Mono, then Left and Right will have separately editable
fields. Otherwise, they are controlled together as a pair from the Left field alone.
Also use these fields to set the language through the following three options:
Any language, if the language is set to All.
The currently available languages, if the Dspl is set to Avail.
def (default), if the Dspl field is set to either All or Avail. Press the
buttons to specify the desired option. Press the ENTER button to confirm the
selection and exit the field.
The following bullets describe the rules that govern which language is used:
•If def (default) is selected, the Audio 1 and Audio 2 outputs default to the first
and second language, respectively, that is listed for the service. It is suggested
that programmers run their language listing so that this default is the language
that matches the audio.
•If the AudioMix field (described on page 30) is set to Surround, Stereo, or
Mono and the user’s choice for language is not available, the audio output is the
default language.
•If the AudioMix field (described on page 30) is set to Dual Mono and a
language pair is not available that matches the user’s choice for Left and Right
languages, the DSR-6100 selects and outputs the first occurrence of the Left
language choice. The system cannot take a Left from one audio pair and a Right
from another. If there is no match for the Left language choice, the DSR-6100
uses the default language.
•There is an interaction between the Language (Lang) menu and the AudioMix
field (described on page 30): If the user had previously selected Stereo or Mono
in the AudioMix field and a specific language as the audio output in the Lang
menu, but later changes the AudioMix menu setting to Dual Mono, the Dual
Mono changes in this menu to the same language specified for both Dual Mono
channels and a caution screen displays. After changing the AudioMix menu to
Dual Mono, reselect the languages desired here, in this menu.
•If the user previously selected Dual Mono in the AudioMix field with two
different languages as audio outputs in the Language menu, but later selects
Stereo, Stereo Surround, or Mono in the AudioMix field, the output in this
Language menu defaults to the first occurrence of a specified language (the one
defined for the Left channel first, then for Right channel if there is no match for
the Left). In this case, the same caution screen appears.
InputMode Field
This read-only field indicates the incoming audio mode of the active service.
DSR-6100 45
Page 52
3
TEXT LANG Display
E Off
Text Lang Menu
This Text Language menu has the Display field and is used to modify and view the
status of the language of the video subtitles. Press the
Lang (Text Language) menu appears.
Display FieldDefault: Off
Press the 4 button until the cursor is at the Display label and press the ENTER
button to move into the field.
This field has the following options:
•OffThis option disables subtitles. Press the ENTER button to confirm the
selection and exit the field.
buttons until the Text
•StatusUse this option to view the actual text language. The actual language can
differ from the chosen language when the user’s choice for language is
unavailable. The bullets on page 45 describe the rules that govern which
language is used. Press the ENTER button to confirm the selection and
exit the field.
•AvailUse the Available option to scroll through the languages supported by
the system while the cursor is in the field. Furthermore, selection of
this option allows you to scroll through only the languages available
for the active service. (If the active service has only three languages,
as listed for the Virtual Channel or program, only three appear. If the
user changes the service, the number of languages may also change.)
Press the ENTER button to confirm the selection and exit the field.
•AllUse this option to enter the desired subtitle language in the Subtitle
field which may or may not be present in that service. You may wish
to select languages that are not functional at this time, but will be
functional in the future. Press the ENTER button to confirm the
selection and exit the field.
46
Page 53
Subtitle FieldDefault: def
TEXT LANG Display Subtitle
E All def
Press the 4 button until the cursor is at the Subtitle label, and press the ENTER
button to move into the field.
Use one of the following options to set the language:
•If the Display is set to All, use the Subtitle field to specify any language. Use
the arrow button (
4
) to enter the three-letter code.
•If the Display is set to Avail, the Subtitle field will list the currently available
languages.
Press the
buttons to specify the desired option. Press the ENTER button to
confirm the selection and exit the field.
Note: If the Display field is set to Status, use the read-only Subtitle field to view the
current language.
DSR-6100 47
Page 54
3
E hh-hh-hh-hh-hh-hh
PORT 10/100 MAC Address
E Disable DSR6100-XXXXX
PORT 10/100 DHCP Unit Name
IP Menus
Use the IP menus to configure the 10/100 and GigE ports.
10/100 MAC Address Menu
Use the following procedure to view the 10/100 MAC address for the left Ethernet
port on the back panel of the DSR-6100. Press the
MAC Address menu appears. This menu displays the Ethernet port’s MAC
address. The address is represented in a hexadecimal format and it is not editable.
10/100 DHCP Menu
buttons until the 10/100
Press the
buttons until the Port 10/100 DHCP menu appears. The front panel
screen displays the DHCP and Unit Name fields. DHCP (Dynamic Host Configuration Protocol) allows the Satellite Multiplex Decrypter to obtain a set of IP parameters from a DHCP server. The DHCP server ensures that all these IP addresses are
unique. This automates and facilitates the Satellite Multiplex Decrypter's access to
the network. The management of the IP address pool, in this case, is handled by the
server, and not by a human administrator.
DHCP FieldDefault: Disable
Move into the field and choose either Enable or Disable.
Unit Name FieldDefault: DSR6100-XXXXX
The Unit Name is fully editable. It is placed into the outgoing DHCP request and is
used for registration. The Unit Name, in most cases, is only a suggestion to the DHCP
server and may be updated with a different name upon receiving the DHCP registration
reply. If an updated name is received from a DHCP server, the Unit Name will be
adjusted to show this change and will replace the user-entered name. The default name
is DSR6100-XXXXX. The XXXXX is the DSR-6100’s IP address in decimal.
48
Page 55
10/100 IP Address MenuDefault: 192.168.000.100
E 192.168.000.100
PORT 10/100 IP Address
E 255.255.255.000
PORT 10/100 Subnet Mask
Use the following procedure to set and view the IP address for the left Ethernet port on
the back panel of the DSR-6100. Press the
buttons until the IP Address menu
appears. Use this menu to enter an IP address for the Ethernet port. The address is
represented in the common dotted-decimal format. Contact the network administrator
for details about configuring the Ethernet port for operation on your local network.
Important: Do not configure the IP Address of the 10/100 and GigE to be on the
same subnet.
Press the 4 button until the cursor is at the IP Address label, and press the ENTER
button to move into the field. Use the arrow buttons (
4
) to enter the desired
address and then press ENTER to confirm the selection and exit the field.
10/100 Subnet Mask MenuDefault: 255.255.255.000
Use the following procedure to set and view the Subnet Mask address for the left
Ethernet port on the back panel of the DSR-6100. Press the
Subnet Mask menu appears. The subnet mask is represented in the common dotteddecimal format. Contact the network administrator for details about configuring the
Ethernet port for operation on your local network.
buttons until the
Press the 4 button until the cursor is at the Subnet Mask label, and press the ENTER
button to move into the field. Use the arrow button (
address and then press the ENTER button to confirm the selection and exit the field.
Use the following procedure to set and view the Default Gateway address for the left
(10/100) Ethernet port on the back panel. Press the
buttons until the 10/100
Default Gateway menu appears. The IP Gateway is an address that is represented in
the common dotted-decimal format. Contact the network administrator for details
about configuring the Ethernet port for operation on your local network.
Press the 4 button until the cursor is at the 10/100 Default Gateway label, and
press the ENTER button to move into the field. Use the arrow buttons (
4
)
to enter the desired gateway address and press the ENTER button to confirm the
selection and exit the field.
Port GigE MAC Address MenuDefault: hh:hh:hh:hh:hh:hh
To view the GigE MAC address for the right Ethernet port on the back panel, press
the
buttons until the Port GigE menu appears. The address is represented in a
hexadecimal format and it is not editable.
GigE IP Address MenuDefault: 192.168.054.100
Use the following procedure to set and view the GigE IP address for the right
Ethernet port on the back panel of the DSR-6100. Press the
GigE IP Address menu appears. The address is represented in the common dotteddecimal format. Contact the network administrator for details about configuring the
GigE port for operation on your local network.
Important: Do not configure the IP Address of the 10/100 and GigE to be on the
same subnet.
buttons until the
Press the4button until the cursor is at the IP Address label, and press the ENTER
button to move into the field. Use the arrow buttons (
address and then press the ENTER button to confirm the selection and exit the field.
50
4
) to enter the desired
Page 57
GigE Subnet Mask MenuDefault: 255.255.255.000
PORT GigE Subnet Mask
E 255.255.255.000
PORT GigE Default Gateway
E 192.168.054.002
Use the following procedure to set and view the GigE Subnet Mask for the right
Ethernet port on the back panel of the DSR-6100. Press the
buttons until the
GigE Subnet Mask menu appears. The GigE subnet mask is represented in the
common dotted-decimal format. Contact the network administrator for details
about configuring the GigE port for operation on your local network.
Press the4button until the cursor is at the Subnet Mask label, and press the ENTER
button to move into the field. Use the arrow button (
4
) to enter the desired
address and then press the ENTER button to confirm the selection and exit the field.
GigE Default Gateway MenuDefault: 192.168.054.002
Use the following procedure to set and view the GigE Default Gateway address for
the right Ethernet port on the back panel of the DSR-6100. Press the
until the GigE Default Gateway Address menu appears. The GigE Default Gateway
is an address that is represented in the common dotted-decimal format. Contact the
network administrator for details about configuring the GigE port for operation on
your local network.
buttons
Press the 4 button until the cursor is at the GigE Default Gateway label, and press
the ENTER button to move into the field. Use the arrow buttons (
enter the desired address and then press the ENTER button to confirm the selection
and exit the field.
DSR-6100 51
4
) to
Page 58
3
GigE TS Mode Menu
Press the
buttons until the Port GigE TS Mode menu appears. Use this menu
to select which transport stream is routed to the GigE port and whether the DSMCC
data is also routed to the GigE port.
TS Mode FieldDefault: Off
Press the 4 button until the cursor is at the TS Mode label, and press the ENTER
button to move into the field. Press the
options: Off, Transcoded, Passthru, or Transcoded+Passthru. When the Passthru or
Transcoded+Passthru is selected, a copy of the ASI #1 transport stream is routed to
the GigE port. When the Transcoded or Transcoded+Passthru is selected, a copy of
the ASI #2 transport stream is routed to the GigE port. Press ENTER to confirm the
selection and exit the field.
DSMCC FieldDefault: Off
Press the 4 button until the cursor is at the DSMCC label, and press the ENTER
button to move into the field. Press the
When On is selected, the DSR-6100 outputs an IP stream that contains DSMCC
data, when the input MPEG-4 program contains DSMCC data. Press ENTER to
confirm the selection and exit the field.
buttons to choose one of the four
buttons to choose either Off or On.
52
GigE Xcoder Dest Addr Menu
Press the
this menu to set the GigE transcoded destination address and the associated port.
Xcoded Dest Addr FieldDefault: 192.168.054.201
Press the 4 button until the cursor is at the Xcoded Dest Addr label, and press the
ENTER button to move into the field. Use the arrow button (
desired address and press the ENTER button to confirm the selection and exit the field.
Port FieldDefault: 06100
Press the 4 button until the cursor is at the Port label, and press the ENTER button
to move into the field. Use the arrow button (
and then press the ENTER button to confirm the selection and exit the field.
buttons until the Port GigE Xcoder Dest Addr menu appears. Use
4
) to enter the desired value
4
) to enter the
Page 59
GigE PassThru Dest Addr Menu
Press the
buttons until the Port GigE PassThru Dest Addr menu appears. Use
this menu to set the GigE pass through destination address and the associated port.
PassThru Dest Addr FieldDefault: 192.168.054.200
Press the 4 button until the cursor is at the PassThru Dest Addr label, and press the
ENTER button to move into the field. Use the arrow button (
desired address and then press the ENTER button to confirm the selection and exit
the field.
Port FieldDefault: 06000
Press the 4 button until the cursor is at the Port label, and press the ENTER button
to move into the field. Use the arrow button (
4
) to enter the desired value
and then press the ENTER button to confirm the selection and exit the field.
4
) to enter the
DSR-6100 53
Page 60
3
Status Display Menus
Status display menus provide information regarding the current status of the
DSR-6100. This menu lists important Satellite Multiplex Decrypter parameters.
These fields are not editable, and the displayed information is either (1) the result of
changes in an installation or channel selection menu, or (2) a parameter the
DSR-6100 reports as part of its operation.
Status0 Menu
Press the
This status-only field displays the following status conditions. Press the 4 button
until the cursor is at the Health label, and press the ENTER button. Use the
buttons to scroll through any errors displayed.
•GoodNo Alarm Condition. The DSR-6100 is
•Alarm:Video lostThe DSR-6100 does not have primary Video
•Alarm:Signal lostThe DSR-6100 does not have signal lock.
•Alarm:Authorization lostThe DSR-6100 is not authorized for the
•Alarm:Fan faultOne or more fans have stopped working and
•Alarm:Transcodes FaultOne of the transcoders has faulted.
buttons until the Status0 menu appears.
working correctly.
Out. This could be due to loss of authorization
or signal.
current service.
need to be replaced.
Note: When the Alarm Trigger (described on page 33) is set to Disable, the
STATUS0 Health field displays Good, even if error conditions are present.
54
Page 61
Status1 Menu
E Local Control L-Band
STATUS1 FrontPanel Input Type
Press the
FrontPanel Field
This status-only field displays whether the user is able to control the DSR-6100
completely from the front panel or whether some front-panel functions are
disabled. When this field displays Local Control, this means the panel is not locked
and the local user has access to all menu functions. This means the DSR-6100
provides typical front-panel control. All menus and fields operate as described in
this manual. When Locked-Out is displayed, access to front-panel control is
disabled by the Uplink Programmer.
Input Type Field
This status-only field displays the input connector on which the active signal is
received. This field displays one of three messages:
•L-BandThis designates the input source (from RF Port 1 to RF Port 8 on the
buttons until the Status1 menu appears.
back panel).
•ASIThis designates the input source is from ASI In port on the
back panel.
•GigE-InThis designates the input source is from GigE In port on the
back panel.
DSR-6100 55
Page 62
3
E ----------
STATUS2 Source Channel Quality
E |||||||||||||||||||||||.......
STATUS3 Signal Quality
Status2 Menu
This menu does not appear if the Input field (described on page 25) is set to ASI
In or GigE In. Press the
screen displays the source name, channel number, and the signal quality of the
incoming signal.
Source Field
This status-only field displays the source name, which was entered by the
programmer or network operator at the encoder/uplink to identify the source.
Dashes are displayed when no information is available.
Channel Field
buttons until the STATUS2 menu appears. This
This status-only field displays the selected Virtual Channel number (from the
Channel menu). Dashes are displayed when no information is available.
Quality Field
This status-only field displays a number from 1 to 100 so that the quality level of
the signal can be judged. The signal quality is also displayed as a large bar graph in
the Status3 menu. If it is 35 or less, take action at your site to increase the dish size
or improve the Low Noise Block (LNB) to prevent occasional loss of output.
Status3 Menu
This menu does not appear if the Input field (described on page 25) is set to ASI In
or GigE In. Press the
displays the quality level of the signal as a large bar graph that expands to fill the entire
LCD screen. The following example shows the quality at about 75.
buttons until the STATUS3 menu appears. This screen
56
Page 63
Status4 Menu
This menu does not appear if the Input field (described on page 25) is set to ASI In
or GigE In. Press the
displays the satellite name and signal tuning characteristics.
Sat Field
This status-only field displays the satellite name from the downloaded network
information. Dashes (---) are displayed when no information is available.
Freq Field
This status-only field displays the downlink frequency of the L-band signal. This may
be different from the frequency that was initially set in the Manual Tune menu.
Symb Field
This status-only field displays the symbol rate (megasymbols per second) of the Lband signal. Dashes (---) indicate that no information is available.
buttons until the STATUS4 menu appears. This screen
Code Field
This status-only field displays the code rate (Error Control Coding for Forward
Error Correction) of the L-band signal.
Format Field
This status-only field displays the format of the L-band signal. The field displays
either Comb (Combined) or Split. Dashes (---) are displayed when no information
is available.
Status5 Menu
This menu does not appear if the Input field (described on page 25) is set to ASI In
or GigE In. Press the
displays the sync, Eb/No, and authorization state of the DSR-6100.
buttons until the STATUS5 menu appears. This screen
DSR-6100 57
Page 64
3
Sync Field
This status-only field displays the acquisition Sync state. The Sync state can be
either Locked or Tuning.
Eb/No Field
This status-only field displays a value from 0.0 to 35.0 that designates a
measurement of the signal-to-noise ratio.
Authorize State Field
This status-only field displays the authorization state of the currently-selected channel.
This field indicates how the Satellite Multiplex Decrypter is authorized. If the
Authorization State is Not Authorized, the field will alternate, and display a reason why
it is not authorized (e.g., Missing Map). Table 3-3 describes each authorization state.
Table 3-3: Authorization States
Authorize State Description
Missing MapIncorrect Virtual Channel Table Number
Undefined ChannelIncorrect Virtual Channel Number
Undefined ServiceIncorrect Service Number
UnencryptedService is not Encrypted
UnknownUnknown State
No Program RekeyProgram Rekey Message is Missing
No Working KeyWorking Key Epoch Message is Missing
No Event BlackoutEvent Blackout Message is Missing
No Category KeyMissing Category Key is Missing
Old Category SeqOld Category Sequence in Program Rekey Message
Subscrb With TapeSubscribed With Taping
Subscrb w/o TapeSubscribed Without Taping
Bad Seed ChksumBad Seed Checksum
Not SubscribedNot Subscribed
Regional BlackoutRegional Blackout
Event BlackoutEvent Blackout
Circular BlackoutCircular Blackout
58
Page 65
Status6 Menu
Press the
buttons until the STATUS6 menu appears. This screen displays the
DSR-6100’s Memory (free memory) and Flash memory.
Memory Field
This status-only field displays the amount of free volatile memory in MB units that
is available for use by the operating system.
Flash Field
This status-only field displays the amount of free non-volatile memory in MB units
that is available for use by the operating system.
Status7(SD) Menu
Press the
video encoding configuration for the SD program.
buttons until the Status7(SD) menu appears. This screen displays the
Video Resolution Field
The Video Resolution field indicates the display resolution of the transcoded video.
This is represented as the number of distinct pixels in the horizontal dimension and the
number of scan lines.
Note: The Video Resolution field does not include a designation for
(p) progressive or (i) interlaced to denote the scan type for the SD video.
Bit Rate Field
The Bit Rate field indicates the data rate of the transcoded video.
DSR-6100 59
Page 66
3
0
Status8(SD) Menu
Press the
audio encoding configuration for the transcoded SD program.
Audio Field
Use this field to choose which audio channel to display the status. Press the 4
button until the cursor is at the Audio field, then use the
first audio channel (0) or the second audio channel (1). The default is 0. Press the
ENTER button to confirm the selection and exit the field.
Format Field
This field is always set to PSTHRU (pass-through) and cannot be changed.
Mode Field
The Mode field indicates the mode (stereo or mono) of the transcoded audio for the
selected audio channel. Dashes (---) designate no information is available.
buttons until the Status8(SD) menu appears. This screen displays the
buttons to choose the
BitRt Field
The BitRt (Bit Rate) field indicates the data rate of the transcoded audio. Dashes (---)
designate no information is available.
Status9(HD) Menu
Press the
the video encoding configuration for the transcoded HD program.
Video Field
The Video field indicates the format of the incoming video, either MPEG-2 or
MPEG-4.
Resolutn Field
The Video Resolution field indicates the display resolution of the transcoded video.
buttons until the Status9(HD) menu appears. This screen displays
60
Page 67
This is represented as the number of distinct pixels in the horizontal dimension and
0
the number of scan lines.
Note: The Video Resolution field does not include a designation for
(p) progressive or (i) interlaced to denote the scan type for the SD video.
BitRt Field
The BitRt (Bit Rate) field indicates the data rate of the transcoded video.
Status10(HD) Menu
Press the
the audio encoding configuration for the transcoded HD program.
Audio Field
Use this field to choose which audio channel to display the status. Press the 4
button until the cursor is at the Audio field, then use the
first audio channel (0) or the second audio channel (1). The default is 0. Press the
ENTER button to confirm the selection and exit the field.
Format Field
buttons until the Status10HD menu appears. This screen displays
buttons to choose the
This field is always set to PSTHRU (pass-through) and cannot be changed.
Mode Field
The Mode field indicates the mode (stereo or mono) of the transcoded audio for the
selected audio channel. Dashes (---) designate no information is available.
BitRt Field
The Bit Rate field indicates the data rate of the transcoded audio. Dashes (---)
designate no information is available.
DSR-6100 61
Page 68
3
E ----------Off
STATUS11 Addr Field Link Field
Status11 Menu
Press the
displays the multicast IP Address and Link status of the GigE input when receiving
a transport stream input.
Addr field
This status-only field displays the multicast IP address (range 224.000.000.000 to
239.255.255.255) that is currently used to receive an input transport stream in the
common dotted-decimal format. Dashes (---) designate no information is available.
Link field
This status-only field indicates the connection speed (10, 100, or 100 Mbps) of the
GigE port. Off indicates that there is no connection to an Ethernet network.
buttons until the Status11 menu appears. This status-only screen
62
Page 69
Diagnostic Menus
Use the DSR-6100's diagnostic menu to acquire information for troubleshooting
purposes. The menus also provide test waveforms and use other diagnostic
information displayed on an NTSC television monitor connected through the back
panel video output.
CAUTION: Turning on diagnostics changes the video or audio output, and these
diagnostic screens or tones may be transmitted to the cable customers if the unit is
connected to the cable plant.
Press the
Menus FieldDefault: Off
buttons until the DIAGNOSTIC menu appears.
Use the Menus field to enable or disable the on-screen diagnostics. Press
the4button until the cursor is at the MENUS label, and press the ENTER button to
move into the field. Press the
buttons to scroll to the desired screen. Press the
ENTER button to confirm the selection and exit the field.
Notice that if the Menus field is set to any option other than Off, Diag F, or Diag G; the
Clear Cntrs (Clear Counters) field also appears.
Use the
buttons to choose the desired option (Fast Facts 1 through 5 or Diag A
through Diag G) and press the ENTER button to confirm the selection and exit the
field. For more information about Fast Facts screens, see "Diagnostics" on page 75.
Clear Cntrs Field
Use this field to reset selected counters to zero. This field is primarily for use with
hotline troubleshooting, and it is recommended that it be used only when so directed
and does not affect the unit’s operation, but it may give misleading troubleshooting
results. To clear counters, press the4button until the cursor is at the Clear Cntrs label,
and press the ENTER button to move into the field. Press the button to select Yes
and press the ENTER button to reset the counters to zero and return the field to No.
DSR-6100 63
Page 70
3
E Not Inserted
TV PASS CARD Status
Unit Address Menu
Press the
buttons until the Unit Address menu appears. This read-only menu
displays the DSR-6100's 16-digit electronic address (range: 000-00000-00000-000 to
999-99999-99999-999). The program provider uses this address to identify a specific
DSR-6100 for authorization and retune messages. The display enables the user to view
the address from the front panel rather than reading the label on the back panel.
TV Pass Card Menu
The DSR-6100 does not initially require a TV Pass Card®, but if one is required, the
program provider typically supplies one. The program provider uses the TV Pass Card
address and unit address to identify a specific DSR-6100 for authorization messages.
Press the
buttons until the TV Pass Card menu appears.
Use this menu to view the TV Pass Card address from the front panel of the
DSR-6100. There are three Status field options:
•Not Inserted
•xxx-xxxxx-xxxxx-xxx (a unique TV Pass Card address, range: 000-0000000000-000 to 999-99999-99999-999)
•xxx-xxxxx-xxxxx-xxx Needs Mating.
Audio Test Signal Menu
Use this menu to validate audio connection by transmitting internally-generated audible
tones to the audio output ports.
Caution: This selection replaces audio.
64
Page 71
L1/R1 and L2/R2 FieldsDefault: Off
Use the appropriate field (either L1/R1 or L2/R2) to choose one of the following
test tones:
•1000
•4040, 3960(two tones)
At the completion of the test, press the ENTER button to disable the test, exit the
field, and return the field to the default setting (Off).
Video Test Signal Menu
Press the
buttons until the Video Test Signal menu appears. Use the full-field
video test signal to display different test patterns by selecting the Pattern field.
Caution: This selection replaces video.
Pattern FieldDefault: Off
Press the4button until the cursor is at the Pattern label, and press the ENTER
button to move into the field. Press the
Choose from the options listed below:
NTSC/PAL M Test Pattern Options
Color Bar
IRE 100 Ramp
NTSC 7 Comb
Red Field
NTSC 7 Comp
buttons to display the test patterns.
5 Step Stair
Unmod Y Ramp
Off (Default)
Test signals override any active service component, and the DSR-6100 displays
diagnostics over the video test patterns if diagnostics are enabled. (For details, see
"Menus Field" on page 63.) To disable the selected video test signal, return to the
Off setting or press the ENTER button to exit the field.
DSR-6100 65
Page 72
3
E Off Off
AD INSERTION TEST Cue Tone Relay
Ad Insertion Test Menu
Ad insertion signals are generated by the DSR-6100, but controlled by the uplink
programmer. Local cable companies use ad insertion signals to control and to
queue the insertion of commercials in cable headends. There are two ways to
provide ad insertion. One is a dedicated digital DTMF differential output for cue
tones. The other way is to use a dedicated contact closure relay. Use the Ad
Insertion Test menu to turn on and off the cue tones and the relays.
CAUTION: Output to the customers may be interrupted. When turned on, the ad
insertion signals can be sent to the local headed equipment.
Press the
Cue Tone FieldDefault: Off
buttons until the Ad Insertion Test menu appears.
Use this field to turn on and off the cue tone test. Press the4button until the cursor
is at the Cue Tone label, and press the ENTER button to move into the field. Press
the
buttons to display the two options: On and Off. If On is selected, the DSR-
6100 generates a DTMF code (0-9*#ABCD) on the cue tone output. This field
returns to the default value (Off) when the ENTER button is pressed to exit the
field.
Relay FieldDefault: Off
Use the Relay field to individually turn On and Off each of the three ad insertion
relays. Press the4button until the cursor is at the Relay label and press the ENTER
button to move into the field. Press the
available options are Off, Relay1 On, Relay2 On, and Relay3 On. This field returns
to the default value (Off) when the ENTER button is pressed to exit the field.
Note: To review cue tone and relay signal connections on the back panel, see
Figure 2-2 on page 10.
buttons to display the options. The
66
Page 73
4
Troubleshooting
Before contacting the Hotline (described on page 69), review Table 4-1 for problems and suggested solutions.
Table 4-1: Troubleshooting Solutions
ProblemPossible CauseSolutionReference
LCD blank and no LEDs
lit.
LEDs illuminate, but LCD
is blank or too dark to read.
No picture and no signal
LED indication.
Poor audio or low audio
level.
Will not acquire signal
lock.
Incorrect output audio
language.
No power to unit.Plug in the unit.
LCD contrast out
of adjustment.
No LNB signal
port connection.
Audio levels
incorrect.
Port not
configured.
Wrong language
setting or audio
port connection.
Adjust LCD contrast.See Install/Core menu,
Connect LNB coax.See "Connecting the DSR-
Adjust audio levels.See "Audio1 and Audio2
Check port selection,
modulation, and frequency
setting.
Confirm audio connection
choice and related audio
language setting.
Contrast Field.
6100" on page 9.
Gain Menus" on page 32.
See "Installation Menus" on
page 22.
See "AUD1LANG and
AUD2LANG Menus" on
page 44.
DSR-610067
Page 74
Page 75
If You Need Help
For assistance with Motorola Mobility products only, contact the Motorola Mobility
Technical Response Center (TRC), 24 hours a day, 7 days a week:
•Inside the U.S.:1-888-944-HELP (1-888-944-4357)
•Outside the U.S.:1-215-323-0044
•Motorola Online: http://businessonline.motorola.com
This offers a searchable solutions database, technical
documentation, and low-priority issue creation and tracking.
5
Product Support
Calling for Repairs
If repair is necessary, call Motorola Mobility’s authorized repair vendor, World Wide
Digital at 1-800-227-0450 or 1-956-541-0600 for shipping address and a Return for
Service Authorization (RSA) number before sending the unit for repair. The RSA number
must be prominently displayed on all equipment cartons and shipping label. World Wide
Digital is open from 8:00 AM to 5:00 PM Central Time, Monday through Friday.
When shipping equipment for repair, follow these steps:
1. Pack the unit securely.
2. Enclose a note describing the exact problem.
3. Enclose a copy of the invoice to verify the warranty status.
4. Label all cartons and shipping labels with the RSA number.
DSR-610069
Page 76
Page 77
6
Downlink/L-Band Frequency
Conversion Tables
A distributor or programmer can provide the latest L-band frequency plans at purchase time. Use
the following formulas to perform calculations for both C-band and Ku-band transponders, or for
installing a new satellite.
Formula for converting a Ku-band Frequency to an L-band Frequency
Frequency Downlink (DL) <minus> 10,750 MHz <equals> Frequency (L-band)12,019 MHz
if downlink frequency
is 3,740 MHz
-3,740 MHz
1,410 MHz
Example calculation
if downlink frequency
is 12,019 MHz
-10,750 MHz
1,269 MHz
DSR-610071
Page 78
Page 79
7
Language Abbreviations
Note: This list of languages was recommended to system operators as the appropriate identifiers
for audio, subtitle, and text information. Refer to Language Menu operation.
LanguageAbbreviationLanguageAbbreviation
ArabicaraEgyptianegy
ArmenianarmEnglisheng
BalinesebanEsperantoepo
BasquebaqFaroesefao
Batak btkFinnishfin
BengalibenFrenchfre
BhojpuribhoGermanger
BulgarianbulGreekgre
BurmeseburGujaratiguj
CatalancatHebrewheb
ChinesechiHindihin
CroatianscrHiri Motuhmo
Cue (Tones)cueHungarianhun
CzechczeIndonesianind
DanishdanInterlingua ina
DutchdutIranianira
DSR-610073
Page 80
7
LanguageAbbreviationLanguageAbbreviation
IrishiriPhilippine (Other)phi
ItalianitaPolishpol
PanjabipanPortuguesepor
JapanesejpnRajasthaniraj
JavanesejavRomanianrum
KashmirikasRussianrus
KoreankorSamoansmo
KurdishkurScotssco
LatinlatSindhisnd
MalaymaySpanishspa
MandarmdrSwahiliswa
MarathimarSwedishswe
Miscellaneous misTagalogtgl
MongolianmonTamiltam
NepalinepThaitha
NorwegiannorUrduurd
Otomian Lang.otoVietnamesevie
PahlavipalWelshwel
Persianper
74
Page 81
8
Diagnostics
Introduction
The Fast Fact Diagnostic screens (1 through 5) are a part of the unit’s firmware created
during product development and are based on the needs of the particular unit. The Fast
Facts screens are used as a method of viewing information and diagnostic data associated
with the unit. All values and information shown on the Fast Fact Diagnostic screens update
when displayed, unless otherwise noted. Information about these screens is described here
for documentation purposes only.
Notes:
1. Hexadecimal numbers are displayed with none or more leading zeros (0) to pad to their
individual field width.
2. Decimal numbers are right-justified in their individual display rectangle and are not
padded with leading zeros (0).
3. Decimal numbers may be displayed with or without a trailing decimal point to
distinguish them from hexadecimal numbers. The default is no trailing decimal point.
DSR-610075
Page 82
8
E Off
DIAGNOSTIC MENUS
E Diag E No
DIAGNOSTIC MENUS Clear Cntrs
Fast Facts 1 (General Information) [page 77]
Fast Facts 2 (RF Port Configuration) [page 79]
Fast Facts 3 (Video Information) [page 80]
Fast Facts 4 (Audio1 and 2 Information) [page 82]
FF1
FF2
FF3
FF4
Figure 8-1: Fast Fact Diagnostic Screens
Fast Facts 5 (10/100 Ethernet Port Information) [page 83]
Fast Facts 5 (GigE Port Information) [page 84]
FF5
FF5
NOTE: To move
between these two
screens, use the
4
buttons.
Viewing the Fast Fact Diagnostic Screens
The diagnostic screens (Figure 8-1) are available via the On-Screen Display (OSD)
video out using a video monitor connected to the OSD Video Out port on the back
of the unit.
To view the OSD diagnostic screens, press the buttons on the front of the unit
until the Diagnostic menu appears, and press the ENTER button to access the
Diagnostic menu on the unit.
Press the 4 button to navigate to the Menus field and press the ENTER button to
move into the field.
Use the buttons to choose one of the Fast Fact Diagnostic screens.
Note: Pressing the ENTER button while viewing a particular OSD diagnostic
screen allows for the continued display of the OSD diagnostic information while
allowing the user to navigate thru other front-panel menus.
76
Page 83
Fast Facts 1
Unit = 225-03177-05987-128
Firmware = 000148 00017C
Encryption = N/A
VC # = 0132
VCT ID = 0002
Eb/No = -2.0
Sat/Xpndr = T6/7
Polarization = Horz
FEC Rate = 3/4
AB
C
D
E
GH
J
K
L
Service # = 00003
F
Fast Facts 1
Signal = 58
Symbol Rate = 10.51 Msps
Frequency = 1310.00 MHz
Auth State = Undefined Service
Signal State = Searching
Virtual Network = 7
M
O
N
P
I
GigE IP = 000.000.000.000
Q
A
B
CDE
F
G
H
I
The Fast Facts 1 screen displays general information relating to the basic functionality of
the unit.
FieldNameDefinition
UnitDisplays the 16-digit unit address on the screen.
VC#Displays the Virtual Channel number.
DSR-6100 77
FirmwareDisplays the firmware version in the boot sector of ROM and
the application section.
VCT IDDisplays the current VCT ID.
EncryptionDisplays if the current service is encrypted or not.
ServiceDisplays the service number for the current program.
Auth StateIf the current service is encrypted, this field displays the current
Eb/NoShows the Signal to Noise (Eb/No) of the signal.
Signal StateShows the received signal state. It can either be Locked or
authorization state of the IRD.
Searching, depending on whether the IRD is locked to a signal,
or not.
Page 84
8
J
KLMNOPQ
FieldNameDefinition
Sat/XpndrDisplays the satellite name and transponder number. If the
satellite name is null, then the satellite number is used.
Signal Strength/
Signal
Displays the signal quality, if the signal is DigiCipher II. Otherwise, it
displays the Signal Strength. Both values are normalized to be
between 0 and 100%.
PolarizationDisplays the polarization for the currently tuned-to transponder,
either:
HorzHorizontal
VertVertical
Symbol RateDisplays the current symbol rate.
FEC RateDisplays the Forward Error correction (FEC) coding rate.
FrequencyDisplays the current RF frequency.
Virtual NetworkDisplays the DSR-6100’s currently tuned-in Virtual Network.
GigE IPDisplays the current GigE input IP address.
78
Page 85
Fast Facts 2
Port 1 + G7(14) Vert ................. Defined
Port 2 - ---(-) --- ................. Undefined
Fast Facts 2
AB C
DE
Port 3 - ---(-) --- ................. Undefined
Port 4 - ---(-) --- ................. Undefined
Port 5 - ---(-) --- ................. Undefined
Port 6 - ---(-) --- ................. Undefined
Port 7 - ---(-) --- ................. Undefined
Port 8 - ---(-) --- ................. Undefined
A
B
C
D
E
The Fast Facts 2 screen displays the DSR-6100’s port configuration.
FieldNameDefinition
Port NumberThe port number being described (Port 1 through Port 8).
Active Status+Indicates the port is active.
-Indicates the port is inactive.
Satellite NameThe name of the current satellite. The Satellite ID is displayed
within brackets.
Polarization The polarity transponder associated with the port, either:
HorzHorizontal
VertVertical
Configuration StatusThe configuration status of the port, either: Defined, Undefined,
or Not Supported.
DSR-6100 79
Page 86
8
0x0000
0x0000
AB
C
D
E
F
GH
I
J
K
L
MN
O
P
A
B
C
D
E
F
G
H
I
Fast Facts 3
The Fast Facts 3 screen displays information relating to video information.
FieldNameDefinition
Video LockedAn indication of video lock status. Yes denotes the video for the
MonitorDisplays the current output format of the video display.
Video PIDDisplays the current Program Identification (PID) number for
Window DimensionsDisplays the current dimensions of the video display: Width x
PCR PidDisplays the current Program Clock Reference (PCR) PID.
Aspect Mode Displays the current aspect mode for the incoming video.
Source FormatDisplays the source format: either Interlaced or Progressive.
Video SetupDisplays the indication if the video setup (pedestal) is active,
ResolutionDisplays the Horizontal Size x Vertical Size of the received video.
80
unit is being received and locked. No denotes the video is not
being received.
the video.
Height, Xpos : Ypos (or mute)
either Yes or No.
Page 87
FieldNameDefinition
J
K
L
MNO
P
Film ModeDisplays the indication of Film Mode activation. Either Yes
(active) or No (inactive).
Aspect RatioDisplays the aspect ratio of the video within the transport stream.
Video Mute Count
Displays the current video mute count.
(VMC)
Frame RateDisplays the frame rate code of the stream.
PTS : FIFODisplays the video Presentation Time Stamp (PTS) followed by
the Picture FIFO Depth Count.
Chroma RatioDisplays the Chrominance format for the video within the trans-
port stream.
Video RateDisplays the rate (in Mbps) of the video within the transport stream.
DSR-6100 81
Page 88
8
A
B
C
D
E
F
G
H
A
B
C
D
E
F
G
H
A
B
C
D
E
F
G
H
Fast Facts 4 (Audio 1 and 2)
The Fast Facts 4 screen displays information relating to audio information. There are two
columns of information displayed. The left column is for the first audio program, and the
right column is for the second audio program.
82
FieldNameDefinition
Audio LockedDisplays the indication of audio lock status for both audio pro-
grams. If yes, then the audio for the unit is being received and
locked. If No, then the audio is not being received.
Audio PidDisplays the current Audio PID for both audio programs.
PCR PidDisplays the current PCR PID for both audio programs.
TypeDisplays the audio stream type: MPEG, AAC, AC3, etc.
Sample RateDisplays the sampling rate (in kHz) of both audio programs.
Audio MixDisplays the audio processing mode for both audio programs:
Mono, Stereo, Surround, etc.
Language
Displays the preferred language setting for both audio programs.
Preference
Language StatusDisplays the language status for both audio programs.
Page 89
Fast Facts 5 (10/100 Network)
A
B
C
D
Fast Facts 5
(10/100 Ethernet)
Network Status = Link Up
Address Type = Manually Configured
MAC Address = 00:09:0E:CC:70:55
IP Address = 010.077.005.066
Subnet Mask = 255.255.254.000
Gateway = 010.077.004.001
E
F
A
BCD
E
F
The Fast Facts 5 screen displays information relating to the Ethernet port (left RJ-45 port
on back of unit) configuration.
Note: To move between these two Fast Fact 5 screens, use the
4
buttons.
FieldNameDefinition
DSR-610083
Network StatusDisplays connectivity status (either Link Up or Link Down).
Address TypeDisplays address type.
MAC AddressDisplays the MAC address of the unit.
IP AddressDisplays the current IP address of the unit.
Subnet MaskDisplays the current subnet mask of the unit.
GatewayDisplays the current gateway of the unit.
Page 90
8
A
B
C
D
E
Fast Facts 5
(Gigabit Network)
Network Status = Link Down
MAC Address = 00:09:0E:CC:70:55
IP Address = 010.077.005.066
Subnet Mask = 255.255.254.0
Gateway = 010.077.004.201
Output Mode = Disable
Pass-Thru = 192.168.054.700: 6000
Transcoded = 192.168.054.201: 6100
F
G
H
A
B
C
D
E
F
G
H
Fast Facts 5 (Gigabit Ethernet)
The Fast Facts 5 (Gigabit Ethernet) screen displays information relating to Gigabit
Ethernet port (right RJ-45 port on back of unit) configuration.
Note: To move between these two Fast Fact 5 screens, use the
4
buttons.
FieldNameDefinition
Network StatusDisplays the connectivity status (either Link Up or Link Down).
MAC AddressDisplays the MAC Address of the GigE port.
IP AddressDisplays the IP address of the GigE port.
84
Subnet MaskDisplays the Subnet Mask of the GigE port.
GatewayDisplays the Gateway of the GigE port.
Output ModeDisplays type of MPEG streams that are output from the GigE
Pass-ThruDisplays the GigE IP address and port to where the pass-
TranscodeDisplays the GigE IP address and port to where the transcoded
port. This could be off, pass-through, transcoded, or both passthrough and transcoded.
Analog Output LevelAdjustable over the range of 0/-20 dB in 1 dB steps
Frequency Response+
Total Harmonic Distortion0.25% at 1 KHz
RF InF-type connector (Qty 8)
Video OutBNC connector (Qty 1)
OSD Video OutBNC connector (Qty 1)
AlarmTerminal block (Qty 1)
Cue Tone (Labeled: Q+ and Q-)Terminal block (Qty 1)
Audio OutTerminal block (Qty 2)
ISOC DataTerminal block (Qty 1)
ASYNC(not implemented)
Contact Closure (Labeled: Relay 1, 2, and 3)Terminal block
ASI InBNC connector (Qty 1)
1 dB, 20 Hz to 20 KHz
Connectors
ASI OutBNC connector (Qty 2)
AUX Video InBNC connector (Qty 1)
AUX Audio InTerminal block (Qty 1)
CF Type1CF connector (Qty 1)
TV Pass CardTV Pass Card connector (Qty 1)
Ethernet 10/100RJ-45 connector (Qty 1)
Ethernet GigERJ-45 connector (Qty 1)
86
Page 93
Electrical
Power Requirements100 to 240 VAC, 50/60Hz, 1.5A maximum, 290 Btu
LNB Power on RF Port 116 to 22 VDC, 450mA maximum
Mechanical
Dimensions 20.5" x 19" x 1.75"(IRD without packaging)
27" x 22" x 7.5"(IRD with packaging)
Weight18.5 lbs. [8.4 kg](Finished goods with packaging and accessory)
12.5 lbs. [5.7 kg](Without packaging)
Special Instructions
For restricted access locations, install the DSR-6100 only in restricted-access areas (dedicated equipment
rooms, equipment closets, or the like) in accordance with Articles 110-26, 110-27, or the NEC ANSI/NFPA70,
or per the applicable code in the country of installation.
Always connect the protective earthing to one the two permanently-protective Earthing Terminals on the back
panel of the DSR-6100. For exact location, see Figure 2-1 on page 9.
CAUTION: When connecting any of the eight RF IN ports, the RF-IN Antenna cable should only be
connected while the DSR-6100 is properly grounded and the shield of the coaxial cable should be
earthed in accordance with Article 820.93 of the NEC, ANSI/NFPA 70:2005, or equivalent.
DSR-6100 87
Page 94
Page 95
CaringfortheEnvironmentbyRecycling
When you see this symbol on a Motorola pdo not dispose of the product with residentiacommercial waste.
roduct,
l or
uthorities
enbrug
tte symbol på et Motorola-produkt,
GenbrugafditMotorola-
RecyclingyourMotorolaEquipment
Please do not dispose of this product with your residential or commercial waste. Some countries or regions, such as the European Union, have set up systems to collect and recycle electrical and electronic waste items. Contact your local afor information about practices established for your region. If collection systems are not available, call Motorola Customer Service for assistance.
Beskyttelseafmiljøetmedg
Når du ser demå produktet ikke bortskaffes sammen med husholdningsaffald eller erhvervsaffald.
udstyr
Dette produkt må ikke bortskaffes sammen med husholdningsaffald eller erhvervsaffald. Nogle lande eller områder, f.eks. EU, har oprettet systemer til indsamling og genbrug af elektriske og elektroniske affaldsprodukter. Kontakt de lokale myndigheder for oplysninger om gældende fremgangsmåder i dit område. Hvis der ikke findes tilgængelige indsamlingssystemer, kan du kontakte Motorola Kundeservice.
UmweltschutzdurchRecycling
Wenn Sie dieses Zeichen auf einem Produkt von Motorola sehen, entsorgen Sie das Produkt bitte nicht als gewöhnlichen Haus- oder Büromüll.
RecyclingbeiGerätenvonMotorola
Bitte entsorgen Sie dieses Produkt nicht als gewöhnlichen Haus- oder Büromüll. In einigen Ländern und Gebieten, z. B. in der Europäischen Union, wurden Systeme für die Rücknahme und Wiederverwertung von Elektroschrott eingeführt. Erkundigen Sie sich bitte bei Ihrer Stadt- oder Kreisverwaltung nach der geltenden Entsorgungspraxis. Falls bei Ihnen noch kein Abfuhr- oder Rücknahmesystem besteht, wenden Sie sich bitte an den Kundendienst von Motorola.
Cuidarelmedioambientemedianteelreciclaje
Cuando vea este símbolo en un producto Motorola, no lo deseche junto con residuos residenciales o comerciales.
ReciclajedesuequipoMotorola
No deseche este producto junto con sus residuos residenciales o comerciales. Algunos países o regiones, tales como la Unión Europea, han organizado sistemas para recoger y reciclar desechos eléctricos y electrónicos. Comuníquese con las autoridades locales para obtener información acerca de las prácticas vigentes en su región. Si no existen sistemas de recolección disponibles, solicite asistencia llamando el Servicio al Cliente de Motorola.
Recyclagepourlerespectdel'environnement
Lorsque vous voyez ce symbole sur un produit Motorola, ne le jetez pas avec vos ordures ménagères ou vos rebuts d'entreprise.
RecyclagedevotreéquipementMotorola
Veuillez ne pas jeter ce produit avec vos ordures ménagères ou vos rebuts d'entreprise. Certains pays ou certaines régions comme l'Union Européenne ont mis en place des systèmes de collecte et de recyclage des produits électriques et électroniques mis au rebut. Veuillez contacter vos autorités locales pour vous informer des pratiques instaurées dans votre region. Si aucun système de collecte n'est disponible, veuillez appeler le Service clientèle de Motorola qui vous apportera son assistance.
Milieubewustrecycleren
Als u dit symbool op een Motorola-product ziet, gooi het dan niet bij het huishoudelijk afval of het bedrijfsafval.
UwMotorola-materiaalrecycleren.
Gooi dit product niet bij het huishoudelijk afval het of bedrijfsafval. In sommige landen of regio's zoals de Europese Unie, zijn er bepaalde systemen om elektrische of elektronische afvalproducten in te zamelen en te recycleren. Neem contact op met de plaatselijke overheid voor informatie over de geldende regels in uw regio. Indien er geen systemen bestaan, neemt u contact op met de klantendienst van Motorola.
DbaáoĞüoĞrodowisko-recykling
Produktów Motorola oznaczonych tym symbolem nie naleĪy wyrzucaü do komunalnych pojemników na Ğmieci.
RecyklingposiadanegosprzĊtuMotorola
Produktu nie naleĪy wyrzucaü do komunalnych pojemników na Ğmieci. W niektórych krajach i regionach, np. w Unii Europejskiej, istnieją systemy zbierania i recyklingu sprzĊtu elektrycznego i elektronicznego. Informacje o utylizacji tego rodzaju odpadów naleĪy uzyskaü od wáadz lokalnych. JeĞli w danym regionie nie istnieją systemy zbierania odpadów elektrycznych i elektronicznych, informacje o utylizacji naleĪy uzyskaü od biura obsáugi klienta firmy Motorola (Motorola Customer Service).
Cuidandodomeioambienteatravésdareciclagem
Quando você ver este símbolo em um produto Motorola, não descarte o produto junto com lixo residencial ou comercial.
ReciclagemdoseuequipamentoMotorola
Não descarte este produto junto com o lixo residencial ou comercial. Alguns países ou regiões, tais como a União Européia, criaram sistemas para colecionar e reciclar produtos eletro-eletrônicos. Para obter informações sobre as práticas estabelecidas para sua região, entre em contato com as autoridades locais. Se não houver sistemas de coleta disponíveis, entre em contato com o Serviço ao Cliente da Motorola para obter assistência.
Caring for the Environment by
Recycling
When you see this symbol on a Motorola p
do not dispose of the product with residentia
commercial waste.
roduct,
l or
uthorities
enbrug
tte symbol på et Motorola-produkt,
Genbrug af dit Motorola-
Recycling your Motorola Equipment
Please do not dispose of this product with your residential or
commercial waste. Some countries or regions, such as the
European Union, have set up systems to collect and recycle
electrical and electronic waste items. Contact your local a
for information about practices established for your region. If
collection systems are not available, call Motorola Customer
Service for assistance.
Beskyttelse af miljøet med g
Når du ser de
må produktet ikke bortskaffes sammen med
husholdningsaffald eller erhvervsaffald.
udstyr
Dette produkt må ikke bortskaffes sammen med husholdningsaffald eller erhvervsaffald. Nogle
lande eller områder, f.eks. EU, har oprettet systemer til indsamling og genbrug af elektriske og
elektroniske affaldsprodukter. Kontakt de lokale myndigheder for oplysninger om gældende
fremgangsmåder i dit område. Hvis der ikke findes tilgængelige indsamlingssystemer, kan du
kontakte Motorola Kundeservice.
Umweltschutz durch Recycling
Wenn Sie dieses Zeichen auf einem Produkt von
Motorola sehen, entsorgen Sie das Produkt bitte
nicht als gewöhnlichen Haus- oder Büromüll.
Recycling bei Geräten von Motorola
Bitte entsorgen Sie dieses Produkt nicht als gewöhnlichen Haus- oder Büromüll. In einigen
Ländern und Gebieten, z. B. in der Europäischen Union, wurden Systeme für die Rücknahme und
Wiederverwertung von Elektroschrott eingeführt. Erkundigen Sie sich bitte bei Ihrer Stadt- oder
Kreisverwaltung nach der geltenden Entsorgungspraxis. Falls bei Ihnen noch kein Abfuhr- oder
Rücknahmesystem besteht, wenden Sie sich bitte an den Kundendienst von Motorola.
Cuidar el medio ambiente mediante
el reciclaje
Cuando vea este símbolo en un producto
Motorola, no lo deseche junto con residuos
residenciales o comerciales.
Reciclaje de su equipo Motorola
No deseche este producto junto con sus residuos residenciales o comerciales. Algunos países o
regiones, tales como la Unión Europea, han organizado sistemas para recoger y reciclar
desechos eléctricos y electrónicos. Comuníquese con las autoridades locales para obtener
información acerca de las prácticas vigentes en su región. Si no existen sistemas de recolección
disponibles, solicite asistencia llamando el Servicio al Cliente de Motorola.
Recyclage pour le respect de
l'environnement
Lorsque vous voyez ce symbole sur un produit
Motorola, ne le jetez pas avec vos ordures
ménagères ou vos rebuts d'entreprise.
Recyclage de votre équipement Motorola
Veuillez ne pas jeter ce produit avec vos ordures ménagères ou vos rebuts d'entreprise. Certains
pays ou certaines régions comme l'Union Européenne ont mis en place des systèmes de collecte
et de recyclage des produits électriques et électroniques mis au rebut. Veuillez contacter vos
autorités locales pour vous informer des pratiques instaurées dans votre region. Si aucun
système de collecte n'est disponible, veuillez appeler le Service clientèle de Motorola qui vous
apportera son assistance.
Milieubewust recycleren
Als u dit symbool op een Motorola-product ziet,
gooi het dan niet bij het huishoudelijk afval of het
bedrijfsafval.
Uw Motorola-materiaal recycleren.
Gooi dit product niet bij het huishoudelijk afval het of bedrijfsafval. In sommige landen of regio's
zoals de Europese Unie, zijn er bepaalde systemen om elektrische of elektronische
afvalproducten in te zamelen en te recycleren. Neem contact op met de plaatselijke overheid
voor informatie over de geldende regels in uw regio. Indien er geen systemen bestaan, neemt u
contact op met de klantendienst van Motorola.
DbaáoĞü o Ğrodowisko - recykling
Produktów Motorola oznaczonych tym symbolem
nie naleĪy wyrzucaü do komunalnych
pojemników na Ğmieci.
Recykling posiadanego sprzĊtu Motorola
Produktu nie naleĪy wyrzucaü do komunalnych pojemników na Ğmieci. W niektórych krajach i
regionach, np. w Unii Europejskiej, istnieją systemy zbierania i recyklingu sprzĊtu elektrycznego
i elektronicznego. Informacje o utylizacji tego rodzaju odpadów naleĪy uzyskaü od wáadz
lokalnych. JeĞli w danym regionie nie istnieją systemy zbierania odpadów elektrycznych i
elektronicznych, informacje o utylizacji naleĪy uzyskaü od biura obsáugi klienta firmy Motorola
(Motorola Customer Service).
Cuidando do meio ambiente
através da reciclagem
Quando você ver este símbolo em um produto
Motorola, não descarte o produto junto com lixo
residencial ou comercial.
Reciclagem do seu equipamento Motorola
Não descarte este produto junto com o lixo residencial ou comercial. Alguns países ou regiões,
tais como a União Européia, criaram sistemas para colecionar e reciclar produtos eletroeletrônicos. Para obter informações sobre as práticas estabelecidas para sua região, entre em
contato com as autoridades locais. Se não houver sistemas de coleta disponíveis, entre em
contato com o Serviço ao Cliente da Motorola para obter assistência.
For full details, see the following link:
www.Motorola.com/recycling
Page 96
Page 97
Page 98
6450 Sequence Dr.
San Diego, CA 92121
Document No: 578523-001, Rev. B
PLEASE RECYCLE
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.