Motorola Avigilon 2.0C-H5SL-D1-IR, Avigilon 2.0C-H5SL-D1, Avigilon 2.0C-H5SL-DO1-IR, Avigilon 3.0C-H5SL-D1, Avigilon 3.0C-H5SL-D1-IR Installation Manual

...

Download

Page 1

InstallationGuide

Avigilon H5SL DomeCamera Models:

1.3C-H5SL-D1 1.3C-H5SL-D1-IR 1.3C-H5SL-DO1-IR

2.0C-H5SL-D1 2.0C-H5SL-D1-IR 2.0C-H5SL-DO1-IR

3.0C-H5SL-D1 3.0C-H5SL-D1-IR 3.0C-H5SL-DO1-IR

5.0C-H5SL-D1 5.0C-H5SL-D1-IR 5.0C-H5SL-DO1-IR

Page 2

Legal Notices

©2019,Avigilon Corporation. All rights reserved. AVIGILON, the AVIGILON logo, AVIGILONCONTROL CENTER, and ACC are trademarks of Avigilon Corporation. Other names or logos mentioned herein may be the trademarks of their respective owners. The absence of the symbols ™ and ® in proximity to each trademark in this document or at all is not a disclaimer of ownership of the related trademark. Avigilon Corporation protects its innovations with patents issued in the United States of America and other jurisdictions worldwide (see avigilon.com/patents). Unless stated explicitly and in writing, no license is granted with respect to any copyright, industrial design, trademark, patent or other intellectual property rights of Avigilon Corporation or its licensors.

Disclaimer

This document has been compiled and published using product descriptions and specifications available at the time of publication. The contents of this document and the specifications of the products discussed herein are subject to change without notice. Avigilon Corporation reserves the right to make any such changes without notice. Neither Avigilon Corporation nor any of its affiliated companies: (1) guarantees the completeness or accuracy of the information contained in this document; or (2) is responsible for your use of, or reliance on, the information. Avigilon Corporation shall not be responsible for any losses or damages (including consequential damages) caused by reliance on the information presented herein.

Avigilon Corporation avigilon.com

PDF-H5SLDO-A

Revision: 1 - EN

20190829

Page 3

Important Safety Information

This manual provides installation and operation information and precautions for the use of this device. Incorrect installation could cause an unexpected fault. Before installing this equipment read this manual carefully. Please provide this manual to the owner of the equipment for future reference.

This Warning symbol indicates the presence of dangerous voltage within and outside the product enclosure that may result in a risk of electric shock, serious injury or death to persons if proper precautions are not followed.

This Caution symbol alerts the user to the presence of hazards that may cause minor or moderate injury to persons, damage to property or damage to the product itself if proper precautions are not followed.

WARNING — Failure to observe the following instructions may result in severe injury or death.

l Installation must be performed by qualified personnel only, and must conform to all local codes.

l For EN 50121-4 compliance, this product is intended to be supplied by a EN 50121-4 power source.

l The H5SL-D product is intended to be supplied by Power over Ethernet (PoE) that is a “Limited

Power Source” or “LPS” rated 48 VDC, 5W min.

l The H5SL-DO product is intended to be supplied by Power over Ethernet (PoE) that is a “Limited

Power Source” or “LPS” rated 48 VDC, 8W min.

l Any external power supply connected to this product may only be connected to another Avigilon

product of the same model series. External power connections must be properly insulated.

l Do not connect directly to mains power for any reason.

CAUTION — Failure to observe the following instructions may result in injury to persons or damage to the device.

l Do not expose the camera directly to high levels of x-ray, laser, or UV radiation. Direct exposure may

cause permanent damage to the image sensor.

l Do not install near any heat sources such as radiators, heat registers, stoves, or other sources of heat.

l Do not subject the device cables to excessive stress, heavy loads or pinching.

l Do not open or disassemble the device. There are no user serviceable parts.

l Refer all device servicing to qualified personnel. Servicing may be required when the device has

been damaged (such as from a liquid spill or fallen objects), has been exposed to rain or moisture, does not operate normally, or has been dropped.

l Do not use strong or abrasive detergents when cleaning the device body.

l Use only accessories recommended by Avigilon.

iii

Page 4

Regulatory Notices

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

l Reorient or relocate the receiving antenna.

l Increase the separation between the equipment and the receiver.

l Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

l Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications made to this equipment not expressly approved by Avigilon Corporation or parties authorized by Avigilon Corporation could void the user’s authority to operate this equipment.

Disposal and Recycling Information

When this product has reached the end of its useful life, please dispose of it according to your local environmental laws and guidelines.

Risk of fire, explosion, and burns. Do not disassemble, crush, heat above 100 °C (212 °F), or incinerate.

European Union:

This symbol means that according to local laws and regulations your product should be disposed of separately from household waste. When this product reaches its end of life, take it to a collection point designated by local authorities. Some collection points accept products for free. The separate collection and recycling of your product at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment.

Page 5

Table of Contents

Overview 1

Camera Base Front View 1

Camera Base Rear View 2

Camera Base Bottom View 3

Cover View, Surface Mount 4

Mounting Adapter View, Surface Mount 5

Cover View, In-Ceiling Mount 6

Mounting Adapter View, In-Ceiling Mount 7

Cover View, Pendant Wall Mount 8

NPT Adapter View, Pendant Mount 9

Pendant Wall Mount Bracket View 10

Pendant Wall Mount View 11

Surface Mount Installation 12

Required Tools and Materials 12

Camera Package Contents 12

Installation Steps 12

Removing the Dome Cover 13

Inserting Cables through the Sealing Grommet 13

Using the Surface Mount Adapter 14

Mounting the Dome Camera Using the Bottom Cable Entry 14

Mounting the Dome Camera Using the Side Cable Entry 15

Mounting the Dome Camera to an Electrical Box 18

Installing the Camera Base to the Mounting Adapter 19

Installing the Dome Cover 20

In-Ceiling Mount Installation 21

Required Tools and Materials 21

Camera Package Contents 21

Installation Steps 21

Removing the Dome Cover 22

Inserting Cables through the Sealing Grommet 22

Using the In-Ceiling Mounting Adapter 23

Installing the Camera Base to the Mounting Adapter 26

Installing the Dome Cover 28

Pendant Mount Installation 29

Page 6

Required Tools and Materials 29

Package Content 29

Installation Steps 30

Removing the Dome Cover 30

Inserting Cables through the Sealing Grommet 30

Mounting the Dome Camera to a Pipe 31

(Optional) Mounting the Dome Camera to the Pendant Wall Mount 32

Installing the Camera Base to the Mounting Adapter 36

Installing the Dome Cover 37

Connecting to the Camera 39

(Optional) Using the USB Wi-Fi Adapter 39

Assigning an IP Address 39

Accessing the Live VideoStream 40

Aiming the Dome Camera 40

(Optional) Configuring microSD Card Storage 41

Zooming and Focusing the DomeCamera 42

Configuring the Camera 42

Setting the IP Address Using the ARP/Ping Method 42

For More Information 43

Connecting to External Audio and I/O Devices 44

Connection Status LED Indicator 45

Removing the Dome Camera from the Mounting Adapter 46

Resetting to Factory Default Settings 47

Limited Warranty and Technical Support 48

Page 7

Overview

Camera Base Front View

IR illuminator

Provides scene illumination in the IR spectrum.

Only available on -IR models.

Ethernet port

Accepts power and Ethernet connection to the network.

The camera can only be powered by Power over Ethernet (PoE). Server communication and image data transmission also occur over this connection.

Link LED indicator

Indicates if there is an active connection in the Ethernet port.

Connection status LED indicator

Provides information about device operation. For more information, see Connection Status LED

Indicator on page45.

microSD card slot

Accepts a microSD card for onboard storage. For more information, see (Optional) Configuring

microSD Card Storage on page41.

Overview 1

Page 8

Camera Base Rear View

Displayed IR illuminators only available on -IR models.

Azimuth control

Provides control of the image angle.

I/O connector block

Provides connections to external input/output and audio devices.

Micro USB port

Accepts a micro USB to USB adapter. Only required when using the Avigilon USB Wi-Fi Adapter.

Tilt lock thumb screw

Provides a locking mechanism for the image tilt adjustment.

Serial number tag

Device information, product serial number and part number label.

I/O Cable Management Clip

Clip to help secure the I/O cable in place.

Camera Base Rear View 2

Page 9

Camera Base Bottom View

Cable entry hole

An entry hole for the cables required for camera operation.

Lanyard anchor

The safety lanyard attaches to the anchor to prevent the camera from falling during installation.

Vent

Vent to allow moisture vapor to escape the sealed housing and equalize pressure.

Only available on H5SL-DO models.

Camera Base Bottom View 3

Page 10

Cover View, Surface Mount

Dome cover

Vandal resistant dome cover.

Only available on H5SL-DO models. Dome covers for H5SL-D models are not vandal resistant.

Surface mount adapter

Used to mount the dome camera to a wall, ceiling or electrical box.

Tamper resistant screws

Star-shaped captive screws to fix the dome cover to the base.

4. Side cable entry cover

Covers the side cable entry hole.

Cover View, Surface Mount 4

Page 11

Mounting Adapter View, Surface Mount

Lanyard

Connects to the lanyard anchor on the camera base.

Camera housing clips

Snaps to hold camera module during installation.

Cable entry hole

An entry hole for the cables required for camera operation.

Mounting holes

Holes for mounting the adapter to the following:

A — UK standard single gang box

B — Octagon gang box

D — US standard single gang box

Mounting Adapter View, Surface Mount 5

Page 12

Cover View, In-Ceiling Mount

In-ceiling mount adapter

Used to mount the dome camera to a wall, ceiling or electrical box.

Dome cover

Vandal resistant dome cover.

Only available on H5SL-DO models. Dome covers for H5SL-D models are not vandal resistant.

Tamper resistant screws

Star-shaped captive screws to fix the dome cover to the base.

Cover View, In-Ceiling Mount 6

Page 13

Mounting Adapter View, In-Ceiling Mount

Camera housing clips

Snaps to hold camera module during installation.

Lanyard

Connects to the lanyard anchor on the camera base.

Clamps

Manually adjustable clamps for securing the dome camera to the ceiling.

Clamp retainer

Used to hold the clamps together before installation.

Mounting Adapter View, In-Ceiling Mount 7

Page 14

Cover View, Pendant Wall Mount

1. Pendant wall mount (optional)

Used with the NPT adapter to mount the dome camera to a wall in pendant installations.

NPT adapter

Used to mount the dome camera to NPT pipes.

Tamper resistant screws

Star-shaped captive screws to fix the dome cover to the base.

Dome cover

Vandal resistant dome cover.

Only available on H5SL-DO models. Dome covers for H5SL-D models are not vandal resistant.

Cover View, Pendant Wall Mount 8

Page 15

NPT Adapter View, Pendant Mount

Camera housing clips

Snaps to hold camera module during installation.

Lanyard

Connects to the lanyard anchor on the camera base.

1-1/2” NPT thread mount

Standard male 1-1/2” NPT thread mount for mounting the dome camera to a pole or bracket.

NPT Adapter View, Pendant Mount 9

Page 16

Pendant Wall Mount Bracket View

Bracket mounting holes

Points for mounting the pendant wall mount bracket to a mounting surface.

Mounting tabs

Tabs for placing the pendant wall mount onto the bracket.

Mounting points

Points for securing the pendant wall mount to the mounting bracket.

Pendant Wall Mount BracketView 10

Page 17

Pendant Wall Mount View

1-1/2” NPS thread mount

Female NPS thread mount for pendant camera installations.

Pendant wall mount screws

Screws for securing the pendant wall mount to the mounting bracket.

NPT pipe entry hole

A 3/4” NPT threaded hole for NPT pipe conduits.

Pendant Wall Mount View 11

Page 18

Surface Mount Installation

Required Tools and Materials

The following tools are required to complete the installation but are not included in the package:

l No. 2 Phillips screwdriver — for attaching camera to an electrical box or mounting surface.

Camera Package Contents

Ensure the package contains the following:

l Avigilon H5SL Dome Camera (Indoor model — H5SL-D)

Mounting template sticker

4 screws and anchors for solid walls

Surface mount adapter

Side conduit cover

T20 Pin-In star-shaped driver

l Avigilon H5SL Dome Camera (Outdoor model — H5SL-DO)

Mounting template sticker

RJ-45 grommet piercing cap

4 screws and anchors for solid walls

Surface mount adapter

Side conduit cover

Side conduit plate (2 sizes)

Conduit grommet

Cable entry grommet

T20 Pin-In star-shaped driver

Installation Steps

Complete the following sections to install the device.

Surface Mount Installation 12

Page 19

Removing the Dome Cover

Note: Be careful not to scratch or touch the dome bubble. The resulting marks or fingerprints may affect the overall image quality. Keep the protective covers on the outside of the dome bubble until the installation is complete.

l Remove the dome cover by releasing the elastic strap holding the dome cover to the camera base.

Inserting Cables through the Sealing Grommet

Always use the provided sealing grommet to prevent dust and debris from entering the camera.

1. Remove the sealing grommet from the camera base.

2. Push the Ethernet cable through the grommet.

If you are installing the indoor model (H5SL-D), you should be able to simply push the cable, crimped or uncrimped, through the grommet by hand.

If you are installing the outdoor model (H5SL-DO), use one of the following methods:

Removingthe Dome Cover 13

Page 20

a. If the Ethernet cable is uncrimped, push the cable through the grommet.

Note: If you pull multiple cables through the sealing grommet, apply silicone sealant to seal any gaps in the grommet.

b. If the Ethernet cable is already crimped, place the grommet piercing cap on the Ethernet

connector then push the cable through the grommet.

Ensure that the orientation of the cable and grommet matches the one shown in the image.

3. Push any other required cables through the grommet.

Using the Surface Mount Adapter

The dome camera is provided with a surface mount adapter that can be mounted to a wall, ceiling or electrical box.

If the dome camera needs to be installed in a different way, use one of the other mounting adapter options and refer to their sections in this manual for more information.

l In-ceiling mounting adapter (H4SL-MT-DCIL). For more information, see In-Ceiling Mount Installation

on page21.

l Pendant NPT mounting adapter (H4SL-MT-NPTA). For more information, see Pendant Mount

Installation on page29.

Pendant wall mounting adapter (CM-MT-WALL) — must be used with NPT mounting adapter.

Mounting the Dome Camera Using the Bottom Cable Entry

Perform the following steps if the required cables will be coming from inside the mounting surface and the camera will be mounted immediately over the cable hole. Use this procedure on surfaces that can be easily drilled into, and when the cables should be kept out of sight.

Perform the following steps to mount the dome camera to a ceiling or wall:

Usingthe Surface Mount Adapter 14

Page 21

1. Use the mounting template to drill 4 mounting holes into the mounting surface and drill the cable entry hole.

2. Pull the required cables through the cable entry hole.

Make sure the cables are threaded through the sealing grommet from the camera base. For more information, see Inserting Cables through the Sealing Grommet on page30

3. Drive 4 screws to fasten the mounting adapter to the ceiling or wall.

Mounting the Dome Camera Using the Side Cable Entry

Perform the following steps if you will be mounting to a surface with the required cables coming out of an external conduit pipe. Use this procedure if the mounting surface cannot be easily cut, or when cables must be brought along the outside of the mounting surface.

1. Use the mounting template to drill four mounting holes into the mounting surface.

Make sure the mounting template is aligned to where the conduit will enter the mounting adapter.

2. Pull the required cables through the conduit.

3. Slide the side cable cover off the mounting adapter.

Mounting the Dome Camera Using the Side Cable Entry 15

Page 22

4. Depending on the conduit used, make the required adjustments to the side cable entry hole:

l If you are using a 1/2" or 20mm interior conduit, install the provided side conduit cover on to

the mounting adapter.

l If using ¾” or 25mm interior conduit, remove the center knockout piece on the provided side

conduit cover then install the side conduit cover on to the mounting adapter.

Mounting the Dome Camera Using the Side Cable Entry 16

Page 23

l If using ½” or ¾” exterior conduit, install a conduit plate to an external conduit adapter, then

slide the mounting adapter over the conduit and plate assembly. Ensure the plate is compatible with the type of conduit used.

If you are installing the outdoor model (H5SL-DO), you may need to cut off part of the rubber gasket on the mounting adapter to make room for the plate.

Mounting the Dome Camera Using the Side Cable Entry 17

Page 24

5. Drive 4 screws to fasten the mounting adapter to the ceiling or wall.

Mounting the Dome Camera to an Electrical Box

Perform the following steps if the required electrical components and cables will be contained in an electrical gang box inside the mounting surface.

1. Pull the required cables through the cable entry hole.

Make sure the cables are threaded through the sealing grommet from the camera base. For more information, see Inserting Cables through the Sealing Grommet on page30.

2. Use pan head screws to install the mounting adapter to the electrical box.

Select the hole configuration that matches the electrical box shape:

A — UK standard single gang box

B — Octagon gang box

D — US standard single gang box

Mounting the Dome Camera to an ElectricalBox 18

Page 25

Installing the Camera Base to the Mounting Adapter

After you install the mounting adapter, mount the camera base to the adapter.

1. Attach the lanyard on the mounting adapter to the anchor on the camera base.

2. Pull the required cables through the cable entry hole on the camera base.

3. Install the grommet into the cable entry hole on the camera base.

Make sure the grommet flange is securely seated on the inside and outside of the cable entry hole.

4. Connect the network cable to the Ethernet port.

The Link LED will turn on once a network link has been established.

5. If external input or output devices, or audio devices are part of the installation (for example: door contacts, relays, microphone, etc.), connect the devices to the I/O connector block.

For more information, see Connecting to External Audio and I/O Devices on page44.

6. Align the large orange arrow on the camera base to the side cable entry hole on the mounting adapter then press the camera base into the mounting adapter. The camera base clicks into place and is held securely.

Installing the Camera Base to the Mounting Adapter 19

Page 26

Installing the Dome Cover

Note:

Before installing the dome cover, we recommend that you first connect to the camera and adjust the aim, zoom, and focus so that the camera covers the required field of view. For more information, see:

l Connecting to the Camera on page39

l Aiming the Dome Camera on page40

l Zooming and Focusing the DomeCamera on page42

1. Attach the dome cover to the base by tightening the screws with the star-shaped driver.

2. Remove the protective cover on the outside of the dome bubble.

Installing the Dome Cover 20

Page 27