Page 1
Select image from Photo Library
Insert and resize image
to fill up this white area
Send (image) to back
APX™ Two-Way Radios
BERKS COUNTY
APX
TM
7500 O5 Control
Head
Page 2
APXTM 7500 O5
2
Index
DECLARATION OF CONFORMITY
DECLARATION OF CONFORMITY
Per FCC CFR 47 Part 2 Section 2.1077(a)
Responsible Party
Name: Motorola Solutions, Inc.
Address: Motorola Solutions, Inc., 1303 East Algonquin Road Schaumburg, IL60196, U.S.A.
Phone Number: 1-800-927-2744
Hereby declares that the product:
Model Name: APX 4500
conforms to the following regulations:
FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a)
Class B Digital Device
As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below.
Page 3
APXTM 7500 O5
3
Index
DECLARATION OF CONFORMITY
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Page 4
APXTM 7500 O5
4
Index
DECLARATION OF CONFORMITY
Additional FCC Notes to Users
The following FCC information applies to Bluetooth radio options
IC Model Name: PMHN4193A
Description: O2 Bluetooth Option Board
FCC ID: AZ492FT6002
IC: 109U-92FT6002
Conforms to the following regulations: FCC Part 15, Section 15.19, 15.12, and 15.105
Note: Changes or modifications not expressly approved by Motorola may void the users authority, as authorized by the FCC,
to operate this device and should not be made. See 47 CFR Part 15.21. Information to user. The users manual or instruction
manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved
by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation. See 47 CFR Part. 15.19(3).
This device has been tested and found to comply with the limits of Part 15.15 of the FCC rules. Parties responsible for
equipment compliance should note that the limits specified in this part will not prevent harmful interference under all
circumstances.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. See Part 15.105b These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
Page 5
APXTM 7500 O5
5
Index
DECLARATION OF CONFORMITY
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Statements:
This Class B digital apparatus complies with ICES-003 and Radio Standards Specification (RSS) 210.
Page 6
APXTM 7500 O5
6
Index
PRODUCT SAFETY AND RF EXPOSURE COMPLIANCE
Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio.
ATTENTION!
This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements.
Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio (Motorola Publication
part number 6881095C99) to ensure compliance with RF energy exposure limits.
For a list of Motorola-approved antennas and other accessories, visit the following website: http://www.motorola.com/APX
Page 7
APXTM 7500 O5
7
Index
COPYRIGHTS & DISCLAIMER
Computer Software Copyrights
The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other
countries preserve for Motorola certain exclusive rights for copyrighted computer programs including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted
computer program. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modified, reverseengineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by
implication, estoppels, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive license to use that arises by operation of
law in the sale of a product.
Documentation Copyrights
No duplication or distribution of this document or any portion thereof shall take place without the express written permission of Motorola. No part of this manual may be reproduced, distributed,
or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of Motorola.
Disclaimer
The information in this document is carefully examined, and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies. Furthermore, Motorola reserves the right
to make changes to any products herein to improve readability, function, or design. Motorola does not assume any liability arising out of the applications or use of any product or circuit
described herein; nor does it cover any license under its patent rights, nor the rights of others.
Page 8
APXTM 7500 O5
8
Index
Getting Started
Example Description
Home button
or
Buttons and keys are shown in bold print or as an icon.
ZONE Menu entries are shown similar to the way they appear on the radio’s display.
This means “Press the right side of the 4-way Navigation button.”
The following special notations identify certain items:
Page 9
APXTM 7500 O5
9
Index
Radio Parts and Controls
Volume Knob
Menu Select Button*
Indicators Terminal
for Microphone
Dim Button
Home Button
Power On/Off
Button
Channel Knob
Emergency *
Navigation Button *
LED Indicators
Page 10
APXTM 7500 O5
10
Index
Radio Parts and Controls
Push-to-Talk
(PTT) Button
Scan On or Off
Not Programmed
Not Programmed
Page 11
APXTM 7500 O5
11
Index
Radio Parts and Controls
Keypad
Mode Select
0-9
Data Feature Button
Home Button
Navigation Button
Zone Up or Zone Down
Cancel Button ( )
Okay/Select Button ( )
Speaker
PTT Button
Page 12
APXTM 7500 O5
12
Index
Preparing Your Radio for Use
Turning on the Radio
Press the Power On/Off Button briefly to power on the
radio.
After a short time, the red, yellow and green LEDs light
up. The display then shows Zone and channel text, and
menu items display on the screen.
The backlight will turn on to the last selected dim level.
Note: Pressing the Power On/Off Button before the
LED lights up will be ignored.
If FAIL ##/## appears in the display, the radio will not
function until the condition has been corrected.
If ERROR ##/## appears, some non-critical data has
been changed.
If CH MISMATCH appears, means that either the
Control Head has been connected to an incompatible
transceiver, or vice versa.
If your radio does not power up, contact your dealer.
To turn off the radio, press the Power On/Off Button
after the LEDs light up.
Power On/Off Button
Emergency Button
Page 13
APXTM 7500 O5
13
Index
Preparing Your Radio for Use
Validating Compatibility During Power Up
The radio validates and updates the software and
hardware of your control head(s) during power up.
Follow the procedure below when your radio runs this
task.
1 The display shows MAINTENANCE MODE REMOTE
DEVICE; promptly followed by other maintenance
statuses.
2 The display shows UPDATE DONE PLEASE RESET
upon completion.
OR
The display shows UPDATE FAILED PLEASE RESET
when it fails to update.
3 Press the Power On/Off Button to reset. The radio
runs the usual power up operation if the software update
are complete.
OR
The radio runs the Maintenance Mode if the update is
not complete and repeat step 1.
Note: If SW INCOMPLETE appears, use Flashport
Recovery Tool to update the control heads before you
power on the radio again.
Power On/Off Button
Emergency Button
Page 14
APXTM 7500 O5
14
Index
Preparing Your Radio for Use
Adjusting the Volume
Volume Knob
To increase the volume, rotate the Volume Knob
clockwise to increase the volume.
To decrease the volume, rotate the Volume Knob
counterclockwise.
Page 15
APXTM 7500 O5
15
Index
Identifying Radio Controls
Programmable Features
Any reference in this manual to a control that is “preprogrammed” means that the control must be programmed by a
dealer or qualified radio technician using the radio's programming software, in order to assign a feature to that control.
The programmable buttons can be programmed as shortcuts to radio functions or preset channels/groups depending on
the duration of a button press:
• Press – Pressing and releasing rapidly.
• Long press – Pressing and holding for the preprogrammed duration (between 0.25 seconds and 3.75 seconds).
• Hold down – Keeping the button pressed.
Page 16
APXTM 7500 O5
16
Index
Identifying Radio Controls
Accessing the Preprogrammed Functions
You can access various radio functions through one of the
following ways:
• A short or long press of the relevant programmable
buttons.
OR
• Use the Menu Select Button ( ).
Using the Menu Select Buttons
The Menu Select Buttons allow to access the menu
entries of features.
Note: Check with your dealer or system administrator for the
list of features activated in your radio.
Your radio may be preprogrammed differently from the following example,
but the steps for selecting a channel may appear as shown below:
• Press the Menu Select button ( ) directly below CHAN.
Volume Knob
Home
Button
Menu Select Button *
Page 17
APXTM 7500 O5
17
Index
Identifying Radio Controls
Accessing the Preprogrammed Functions (2/3)
Using the Advance Programmable Buttons
Mode Select Button – Programs the current zone and channel to a Mode Select button with a long press on the
Mode Select button. After the buttons are programmed, you can return to the preprogrammed zone and channel with
a short press on the programmed Mode Select button.
Emergency Button *†
Menu Select Button *
Scan On or Off
Side Button 2
Side Button 3
Keypad
Numbers
0-9 †
Page 18
APXTM 7500 O5
18
Index
Identifying Radio Controls
Accessing the Preprogrammed Functions (3/3)
Using the Navigation Buttons
Home Button
The button returns you to the home (default) display. In most cases, this is the current mode.
For selected radio features, the button is also used to save user-edited radio settings or information before
returning you to the Home screen.
Note: Some features do not require you to press to go to the Home screen. Refer to the individual feature sections
in this manual for further details on saving user-edited radio settings or information.
The button also can revert to home channel. Check with your dealer or system administrator for more information.
Data Feature Button (Not Programmed)
Use this button to access data-related features, such as the Text Messaging Service (TMS) feature screen.
4-Way Navigation Button
Use this button to scroll through the radio’s lists or items in the display, or both.
Volume Knob
Use this Volume Knob to adjust the volume of the speakers by turning it clockwise or counterclockwise.
Channel Knob
Use this Channel Knob to scroll the channels by turning it clockwise or counterclockwise.
Page 19
APXTM 7500 O5
19
Index
Extra page intentionally inserted.
Page 20
APXTM 7500 O5
20
Index
Identifying Radio Controls
Using the Keypad (1/4)
You can use the 3 x 4 alphanumeric keypad to access your radio’s features. The keypad functions in a manner similar to a standard
telephone keypad when entering numeric digits. When the keypad is used to edit a list, each key can generate different characters of the
alphabet. The tables below show the number of times a key needs to be pressed to generate the required character.
Keypad Characters – Uppercase Mode
Number of Times Key is Pressed
Key 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
1 . , ? ! ; @ _ - * # & $ / + = \ " ( )
A B C
D E F
G H I
J K L
M N O
P Q R S
T U V
W X Y Z
Toggle between mixed case mode, uppercase mode, and lowercase mode.
Space
Toggle between numeric and letter mode.
Page 21
APXTM 7500 O5
21
Index
Identifying Radio Controls
Using the Keypad (2/4)
Keypad Characters – Lowercase Mode
Number of Times Key is Pressed
Key 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
1 . , ? ! ; @ _ - * # & $ / + = \ " ( )
a b c
d e f
g h i
j k l
m n o
p q r s
t u v
w x y z
Toggle between mixed case mode, uppercase mode, and lowercase mode.
Space
Toggle between numeric and letter mode.
Page 22
APXTM 7500 O5
22
Index
Identifying Radio Controls
Using the Keypad (3/4)
Number of Times Key is Pressed
Key 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
1 . , ? ! ; @ _ - * # & $ / + = \ " ( )
2
3
4
5
6
7
8
9
0
Space
Toggle between numeric and letter mode.
Keypad Characters – Numeric Mode
Page 23
APXTM 7500 O5
23
Index
Identifying Radio Controls
Using the Keypad (4/4)
Keypad Characters – Hexadecimal Mode
Number of Times Key is Pressed
Key 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
1
2 A B
C
3 D E F
4
5
6
7
8
9
0
Not applicable
Not applicable
Page 24
APXTM 7500 O5
24
Index
Identifying Radio Controls
Push-To-Talk (PTT) Button
The PTT button on the side of the microphone serves
two basic purposes:
• While a call is in progress, the PTT button allows the
radio to transmit to other radios in the call.
Press and hold down PTT button to talk. Release the
PTT button to listen.
The microphone is activated when the PTT button is
pressed.
• While a call is not in progress, the PTT button is used
to make a new call.
Push-to-Talk
(PTT) Button
Scan On of Off
Not Programmed
Not Programmed
Page 25
APXTM 7500 O5
25
Index
Identifying Status Indicators
Status Icons
Receiving
Radio is receiving a call or data.
Transmitting
Radio is transmitting a call or data.
Call Received
Radio has received an Individual Call.
Received Signal Strength Indicator (RSSI)
The number of bars displayed represents the
received signal strength for the current site, for
trunking only. The more stripes in the icon, the
stronger the signal.
Direct
• On = Radio is currently configured for direct
radio to radio communication (during
conventional operation only).
• Off = Radio is connected with other radios
through a repeater.
Power Level
• L = Radio is set at Low power.
• H = Radio is set at High power.
Priority-One Channel Scan
• Blinking dot = Radio detects activity on channel
designated as Priority-One.
• Steady dot = Radio detects activity on channel
designated as Priority-Two.
Scan
Radio is scanning a scan list.
User Login Indicator (IP Packet Data)
• On = User is currently associated with the radio.
• Off = User is currently not associated with the
radio.
• Blinking = Device registration or user
registration with the server failed due to an invalid
username or pin.
Secure Operation
• On = Secure operation.
• Off = Clear operation.
• Blinking = Receiving an encrypted voice call.
Data Activity
Data activity is present.
View/Program Mode
Radio is in the view or program mode.
• On steady = View mode
• Blinking = Program mode
Page 26
APXTM 7500 O5
26
Index
Identifying Status Indicators
LED Indicators
Solid red Radio is transmitting.
Rapidly blinking red Radio has failed the self test upon powering up or encountered a fatal error.
Solid yellow Channel is busy.
Blinking yellow Radio is receiving a secured transmission.
Solid green Radio is powering up, or is on a non-priority channel while in the Scan List Programming
mode.
Blinking green Radio is receiving an individual or telephone call, or is on a Priority-Two channel while in
the Scan List Programming mode.
Rapidly blinking green Radio is on a Priority-One channel while in the Scan List Programming mode.
The LED indicator shows the operational status of your radio.
LED Indicators
Page 27
APXTM 7500 O5
27
Index
Identifying Status Indicators
Intelligent Lighting Indicators
This feature temporary changes the backlight of the top display screen and the keypad, and adds a color bar to the main
display screen to help signal that a radio event has occurred.
Note: This feature must be preprogrammed by a qualified radio technician.
Backlight and Bar Color Notification When
Orange Emergency Alerts The radio initiates an emergency alarm or call.
The radio receives an emergency alarm or call.
Red Critical Alerts The radio is out of range.
The radio enters failsoft mode.
The radio is unable to establish a full connection with
the system.
Green Call Alerts The radio receives a private call.
The radio receives a call alert.
Page 28
APXTM 7500 O5
28
Index
Extra page intentionally inserted.
Page 29
APXTM 7500 O5
29
Index
Extra page intentionally inserted.
Page 30
APXTM 7500 O5
30
Index
Alert Tones
IDENTIFYING STATUS INDICATORS
An alert tone is a sound or group of sounds. Your radio uses alert tones to inform you of your radio’s conditions.
The following table lists these tones and when they occur.
You Hear Tone Name Heard
Short,
Low-Pitched
Tone
Play
Radio Self Test Fail When radio fails its power-up self test.
Reject When unauthorized request is made.
Time-Out Timer Warning Four seconds before time out.
No ACK Received When radio fails to receive an acknowledgment.
Individual Call Warning Tone When radio is in an individual call for greater than 6 seconds without any activity.
Talk Prohibit/PTT Inhibit (When PTT button is pressed) transmissions are not allowed.
Long,
Low-Pitched
Tone
Play
Time-Out Timer
Timed Out
After time out.
Out of Range (When PTT button is pressed) the radio is out of range of the system.
Invalid Mode When radio is on an unpreprogrammed channel.
A Group of
Low-Pitched
Tones
Play
Busy When system is busy.
Page 31
APXTM 7500 O5
31
Index
IDENTIFYING STATUS INDICATORS
You Hear Tone Name Heard
Short,
Medium-Pitched
Tone
Play
Valid Key-Press When correct key is pressed.
Radio Self Test Pass When radio passes its power-up self test.
Clear Voice At beginning of a non-coded communication.
Priority Channel Received When activity on a priority channel is received.
Emergency Alarm Entry When entering the emergency state.
Central Echo When central controller has received a request from a radio.
Long,
Medium-Pitched
Tone
Play
Volume Set When volume is changed on a quiet channel.
Emergency Exit When exiting the emergency state.
A Group of
Medium-Pitched
Tones
Play
Fail-soft When the trunking system fails.
Automatic Call Back When voice channel is available from previous request.
Keyfail When encryption key has been lost.
Console Acknowledge When status, emergency alarm, or reprogram request ACK is received.
Received Individual Call When Call Alert or Private Call is received.
Site Trunking When a SmartZone trunking system fails.
Call Alert Sent When Call Alert is received by the target radio.
Page 32
APXTM 7500 O5
32
Index
IDENTIFYING STATUS INDICATORS
You Hear Tone Name Heard
Ringing
Play
Fast Ringing When system is searching for target of Private Call.
Enhanced Call Sent When waiting for target of Private Call to answer the call.
Phone Call Received When a land-to-mobile phone call is received.
Gurgle
Play
Dynamic Regrouping (When the PTT button is pressed) a dynamic ID has been received.
Talk Permit (When PTT button is pressed) verifying system accepting transmissions.
Unique,
Low-Pitched
Chirp
New Message When a new message is received.
Unique,
High-Pitched
Chirp
Priority Status When a priority message is received.
Page 33
APXTM 7500 O5
33
Index
General Radio Operation
Selecting a Zone
Selecting a Radio Channel
Receiving and Responding to a Radio Call
Receiving and Responding to a Talkgroup Call
Receiving and Responding to a Private Call (Trunking Only, Digital Mode Only)
Making a Radio Call
Repeater or Direct Operation
Page 34
APXTM 7500 O5
34
Index
FLEET MAP (SAMPLE)
Page 35
APXTM 7500 O5
35
Index
A zone is a group of channels.
Note: Your radio must be preprogrammed to allow you
to use these features.
1 to ZONE.
2 Press the Menu Select button directly below ZONE.
The display shows the current zone and channel.
3 button until the desired zone is displayed.
4 Press or the PTT button to confirm the selected
zone number.
5 Press the PTT button to begin transmitting on the
displayed zone channel.
General Radio Operation
Selecting a Zone
OR
Use the Zone Up and Zone Down on the Navigation
Button (on either the control head or the keypad
microphone) to change Zones.
Navigation
Button
Volume Knob
Home
Button
Channel Knob
Menu Select Button
Menu Select Items
Nuis Prfl Zone Scan ScnL
Mute Info Rcnt Colr Cnts
Myid
NUID PRFL ZONE SCAN ScnL
Page 36
APXTM 7500 O5
36
Index
A channel is a group of radio characteristics, such as
transmit/ receive frequency pairs.
Note: Your radio must be preprogrammed to allow you
to use this feature. If you select a channel that is not
within the preprogrammed band, the radio indicates that
it is on an unsupported frequency with both audio and
visual warnings.
Consult a qualified radio technician for the right choice
between the following methods.
Rotate the Channel knob until the display shows the
desired channel.
General Radio Operation
Selecting a Radio Channel
Navigation
Button
Volume Knob
Home
Button
Channel Knob
Menu Select Button
MUTE INFO RCNT COLR CNTS
Page 37
APXTM 7500 O5
37
Index
Using Mode Select Feature
Mode Select allows a long press to save your radio’s current
zone and channel to a keypad button; then once programmed, the
short-press of that button or soft key jumps the transmission to
the saved zone and channel.
All the programmable buttons and keypad digit 0 to 9 buttons
allow you to save the frequent used zone and channel.
Procedure:
1 Toggle your zone and channel to the required zone and
channel.
2 Press and hold the digit button you desire to program.
You hear a short, medium-pitched tone when the zone and
channel is saved.
Note: Repeat this procedure to change the zone and channel of
the programmed button.
Short press of the programmed button changes your current
transmission to the zone and channel programmed in this button.
Emergency Button *†
Menu Select Button *
Scan On or Off
Side Button 2
Side Button 3
Keypad
Numbers
0-9 †
Page 38
APXTM 7500 O5
38
Index
General Radio Operation
Receiving and Responding to a Radio Call
Once you have selected the required channel and/or
zone, you can proceed to receive and respond to calls.
You see solid red while the radio is transmitting, and
solid yellow when the radio is receiving a transmission
(conventional mode only). There is no LED indication
when the radio receives a transmission in trunking
mode.
If the radio is receiving a secure transmission, the LED
blinks yellow.
Page 39
APXTM 7500 O5
39
Index
General Radio Operation
Receiving and Responding to a Talkgroup Call
To receive a call from a group of users, your radio must
be configured as part of that talkgroup.
When you receive a talkgroup call (while on the Home
screen), depending on how your radio is
preprogrammed:
1 ASTRO Conventional Only:
The LED lights up solid yellow. The display shows the
talkgroup alias or ID, and the caller alias or ID.
OR
Trunking Only:
The display shows the caller alias or ID.
2 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0
cm) from your mouth.
3 Press the PTT button to respond to the call. The LED
lights up solid red.
4 Release the PTT button to listen.
PTT
Button
Page 40
APXTM 7500 O5
40
Index
General Radio Operation
Receiving and Responding to a Private Call (Trunking, Digital Mode Only)
A Private Call is a call from an individual radio to another
individual radio.
These one-to-one calls between two radios are not
heard by others in the current talkgroup. The calling
radio automatically verifies that the receiving radio is
active on the system and can display the caller ID.
When you receive a Private Call:
1 You hear two alert tones and the LED blinks green.
The display shows CALL RECEIVED and the caller
alias or ID.
2 Press the Menu Select button directly below RESP
within 20 seconds after the call indicators begin.
3 During the call, the display shows the caller alias
(name), if it is in the call list.
OR
During the call, the display shows the caller ID
(number), if the caller’s name is not in the call list.
RESP
Page 41
APXTM 7500 O5
41
Index
General Radio Operation
Repeater or Direct Operation
The REPEATER operation increases the radio’s range
by connecting with other radios through a repeater. The
transmit and receive frequencies are different.
The DIRECT or “talkaround operation” allows you to
bypass the repeater and connect directly to another
radio. The transmit and receive frequencies are the
same.
Move the 16-Position Channel/Talkgroup Select to a
preprogrammed Direct channel in the radio to talk in a
direct/talkaround mode.
The display shows the Talkaround icon if the radio
is currently in Direct mode (during conventional
operation only).
Navigation
Button
Volume Knob
Home
Button
Channel Knob
Menu Select Button
MUTE INFO RCNT COLR CNTS
Page 42
APXTM 7500 O5
42
Index
Advanced Features
Advanced Call Features
Contacts
–Adding a New Contact Entry
–Deleting a Contact Entry
–Adding a Contact to a Call List or Phone List
–Editing a Contact in a Call List
•Editing an Entry Alias
•Editing as Entry ID
•Editing a Call Type
Scan Lists
–Viewing a Scan List
–Editing the Scan List
–Changing the Scan List Status
–Viewing and Changing the Priority Status
Scan
–Turning Scan On or Off
–Transmitting While the Scan is On
•Radio Programmed for Talkback Scan
•Radio Programmed for Non-Talkback Scan
–Deleting a Nuisance Channel
–Restoring a Nuisance Channel
Call Alert Paging
–Answering a Call Alert
Emergency Operation
–Sending an Emergency Alarm with Emergency Call
–Special Considerations for Emergencies
Secure Operations
– Selecting Secure Transmissions
Trunking System Controls
–Using the Failsoft System
–Going Out of Range
–Trunked Announcement
•Initiating an Announcement
Page 43
APXTM 7500 O5
43
Index
Advanced Features
Utilities
–Viewing the Recent Calls List
–Selecting a Radio Profile
–Enabling and Disabling the Radio Alias
–Controlling the Display Backlight
–Changing the Display Color
–Turning Keypad Tones On or Off
–Using the Time-Out Timer
–Using the Digital PTT ID Feature
–Accessing the General Radio Information
•Accessing the Radio Information
•Viewing the IP Information
•Viewing the Control Assignments
•Editing the Soft ID
–Voice Announcement
Page 44
APXTM 7500 O5
44
Index
Contacts
ADVANCED FEATURES
This feature provides “address-book” capabilities on your radio.
Each entry corresponds to an alias (name) or ID (number) that you use to initiate a call.
Contact entries are alphabetically sorted according to entry alias. Each alias can have up to 5 IDs of different call types
associated with it.
Additionally, each entry, depending on context (conventional, trunking, or phone), associates with Private Call, or Call Alert.
Each entry within Contacts displays the following information:
• Call Alias (Name)
• Call ID (Number)
• Call Type (Icon)
• WACN ID (Astro 25 Trunking IDs only)
• System ID
Note. For Berks County, the contact list is set up only to help display the calling radio Alias. A total of 500 default records are
added to the “Unified Call List” for this purpose. No Hot Lists are set up in the radios.
The systems include the Trunking system, ASTRO conventional and MDC conventional.
The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires.
You will hear the Menu Inactive Exit Tone upon feature exit
.
Page 45
APXTM 7500 O5
45
Index
Contacts
Adding a New Contact Entry (1/2)
1 to CNTS.
2 Press the Menu Select button directly below CNTS.
The entries are alphabetically sorted.
3 to [NEW CONTACT] and press the
Menu Select button directly below SEL.
4 The display shows NAME. Press the Menu Select
button directly below EDIT.
Use the keypad to enter the name.
Press to move one space to the left.
Press to move one space to the right.
Press the Menu Select button below DEL to delete
any unwanted characters.
Press to add a space.
Press to toggle between mixed case mode,
uppercase mode, and lowercase mode.
Press to toggle between numeric and letter
mode.
5 Press the Menu Select button directly below OK once
you have entered the name.
OR
Press the Menu Select button directly below CNCL
to return to the previous screen.
6 to [ADD NUMBER] and press the
Menu Select button directly below SEL. The display
shows TYPE 1 <DEFAULT TYPE>.
Navigation
Button
Volume Knob
Home
Button
Channel Knob
Menu Select Button
Menu Select Items
Nuis Prfl Zone Scan ScnL
Mute Info Rcnt Colr Cnts
Myid
MUTE INFO RCNT COLR CNTS
Page 46
APXTM 7500 O5
46
Index
Contacts
Adding a New Contact Entry (2/2)
7 Press Menu Select button directly below EDIT.
8 to the required channel and press the Menu
Select button directly below OK.
9 to NUMBER 1 and press the Menu Select
button directly below EDIT.
The display shows NUMBER 1 and a cursor
appears.
Use the keypad to enter the number.
Press to move one space to the left.
Press to move one space to the right.
Press the Menu Select button directly below DEL to
delete any unwanted characters.
10 Press the Menu Select button directly below OK
once you have entered the number.
OR
Press the Menu Select button directly below CNCL
to return to the previous screen.
11 Press the Menu Select button directly below DONE
once you have finished.
12 The display shows <ENTRY> STORED,
confirming that the contact entry has been added.
13 The radio returns to the main Contacts screen.
Navigation
Button
Volume Knob
Home
Button
Channel Knob
Menu Select Button
Menu Select Items
Nuis Prfl Zone Scan ScnL
Mute Info Rcnt Colr Cnts
Myid
MUTE INFO RCNT COLR CNTS
Page 47
APXTM 7500 O5
47
Index
Contacts
Editing a Contact in a Call List
Editing an Entry Alias
1 to CNTS.
2 Press the Menu Select button directly below CNTS.
The entries are alphabetically sorted.
3 to the entry you want to edit and press the
Menu Select button directly below OPTN.
4 to EDIT and press the Menu Select button
directly below SEL.
5 to the entry alias you wish to change and
press the Menu Select button directly below EDIT.
6 A cursor appears.
Use the keypad to edit the name.
Press to move one space to the left.
Press to move one space to the right.
Press the Menu Select button below DEL to delete
any unwanted characters.
Press to add a space.
Press to toggle between mixed case mode,
uppercase mode, and lowercase mode.
Press to toggle between numeric and letter
mode.
7 Press the Menu Select button directly below OK once
you have finished. The display returns to the Edit
Contact screen.
8 Press the Menu Select button directly below DONE
to save your changes and return to the main screen
for Contacts.
Navigation
Button
Volume Knob
Home
Button
Channel Knob
Menu Select Button
Menu Select Items
Nuis Prfl Zone Scan ScnL
Mute Info Rcnt Colr Cnts
Myid
MUTE INFO RCNT COLR CNTS
Page 48
APXTM 7500 O5
48
Index
Contacts
Deleting a Contact Entry
1 to CNTS.
2 Press the Menu Select button directly below CNTS.
The entries are alphabetically sorted.
3 to the entry you want to delete and press the
Menu Select button directly below OPTN.
4 to DELETE and press the Menu Select
button directly below SEL. The display shows
<ENTRY> CONFIRM DEL?.
5 Select YES to delete the entry.
The display shows <ENTRY> DELETED and the
radio returns to the main screen for Contacts.
OR
Select NO to return to the main screen for Contacts.
Navigation
Button
Volume Knob
Home
Button
Channel Knob
Menu Select Button
Menu Select Items
Nuis Prfl Zone Scan ScnL
Mute Info Rcnt Colr Cnts
Myid
MUTE INFO RCNT COLR CNTS
Page 49
APXTM 7500 O5
49
Index
Scan Lists
ADVANCED FEATURES
Scan lists are created and assigned to individual channels/groups.
Your radio scans for voice activity by cycling through the channel/group sequence specified in the scan list for the current
channel/group.
Your radio supports different types of Scan Lists:
• Trunking Priority Monitor Scan List
• Conventional Scan List
• Talkgroup Scan List
A maximum of 200 Scan Lists can be programmed in your radio.
These lists must be preprogrammed by a qualified radio technician.
Page 50
APXTM 7500 O5
50
Index
Scan Lists
Viewing a Scan List
1 to SCNL.
2 Press the Menu Select button directly below SCNL.
3 to view the members on the list.
4 Press the to exit the current display and return to
the Home screen.
Navigation
Button
Volume Knob
Home
Button
Channel Knob
Menu Select Button
Menu Select Items
Nuis Prfl Zone Scan ScnL
Mute Info Rcnt Colr Cnts
Myid
NUIS PRFL ZONE SCAN SCNL
Page 51
APXTM 7500 O5
51
Index
Scan Lists
Editing the Scan List
This feature lets you change scan list members and
priorities.
Note: The maximum number of members for a trunking
priority monitor scan list is 50; for a conventional scan
list, 30; and for a talkgroup scan list, 250.
Long press the preprogrammed Scan List
Programming button and proceed to Step 3.
OR
1 to SCNL.
2 Press the Menu Select button directly below SCNL.
The display shows the lists that can be changed.
3 to the entry you want to edit.
4 Press the Menu Select button directly below SEL to
add and/or change the priority of the currently
displayed channel in the scan list. OR
Press the Menu Select button directly below DEL to
delete the currently displayed channel from the scan
list.
OR Press the Menu Select button directly below RCL
to view the next member of the scan list.
5 to select more channels to be added or
deleted. OR
Use the keypad to go directly to additional channels to
be added or deleted. OR
Use the Channel Knob to select additional channels
to be added or deleted.
6 Press to exit scan list programming and return to
the Home screen.
Navigation
Button
Volume Knob
Home
Button
Channel Knob
Menu Select Button
Menu Select Items
Nuis Prfl Zone Scan ScnL
Mute Info Rcnt Colr Cnts
Myid
NUIS PRFL ZONE SCAN SCNL
Page 52
APXTM 7500 O5
52
Index
Scan Lists
Changing the Scan List Status
1 Long press the preprogrammed Scan side button.
2 The display shows the programming mode icon and
the first list member.
3 to the number you want to edit.
4 Press the button or press the Menu Select button
directly below SEL once to add the currently
displayed channel to the scan list.
OR
Press the button or press the Menu Select button
directly below SEL, one or more times to change the
scan list status icon of the currently displayed channel.
5 to select more list members whose scan
status you want to change.
OR
Use the keypad to go directly to that scan list member.
OR
Use the Channel Knob to select another scan list
member.
6 Press to exit scan list programming and return to
the Home screen.
Page 53
APXTM 7500 O5
53
Index
Scan
Turning Scan On or Off
Press and release the preprogrammed Scan button on
the mic OR
1 to SCAN.
2 Press the Menu Select button directly below SCAN.
3 The display shows SCAN OFF if scan is disabled.
Press the Menu Select button directly below SCAN
to enable scan.
OR
The display shows SCAN ON and the scan status
icon if scan is enabled. Press the Menu Select button
directly below SCAN to disable scan.
4 The radio returns to the Home screen.
NUIS PRFL ZONE SCAN SCNL
Navigation
Button
Volume Knob
Home
Button
Channel Knob
Menu Select Button
Menu Select Items
Nuis Prfl Zone Scan ScnL
Mute Info Rcnt Colr Cnts
Myid
Scan On or Off
NUIS PRFL ZONE SCAN SCNL
Page 54
APXTM 7500 O5
54
Index
Scan
Transmitting While the Scan is On
Radio Programmed for Non-Talkback Scan
1 Press the PTT button at any time to transmit on the
selected channel or fixed channel.
Page 55
APXTM 7500 O5
55
Index
Scan
Deleting a Nuisance Channel
If a channel continually generates unwanted calls or
noise (termed a “nuisance” channel), you can
temporarily remove the unwanted channel from the scan
list.
This capability does not apply to priority channels or the
designated transmit channel.
1 When the radio is locked onto the channel to be
deleted,
to NUIS.
2 Press the Menu Select button directly below NUIS.
3 Press the Menu Select button directly below
DELETE.
Navigation
Button
Volume Knob
Home
Button
Channel Knob
Menu Select Button
Menu Select Items
Nuis Prfl Zone Scan ScnL
Mute Info Rcnt Colr Cnts
Myid
NUIS PRFL ZONE SCAN SCNL
Page 56
APXTM 7500 O5
56
Index
Scan
Restoring a Nuisance Channel
To restore the deleted nuisance channel, do one of the
following:
• Turn scan off, then on.
OR
• Change modes.
OR
• Turn off the radio, and then turn it back on.
Nuisance mode delete can be disabled by the system
administrator.
Navigation
Button
Volume Knob
Home
Button
Channel Knob
Menu Select Button
Menu Select Items
Nuis Prfl Zone Scan ScnL
Mute Info Rcnt Colr Cnts
Myid
NUIS PRFL ZONE SCAN SCNL
Page 57
APXTM 7500 O5
57
Index
Call Alert Paging
Answering a Call Alert
1 When you receive a Call Alert page, you hear four
repeating alert tone and the green LED blinks.
2 The call received icons blinks and the display shows
PAGE RECEIVED.
3 Press the PTT button to answer.
OR
Press any button to clear the Call Alert page.
PTT
Button
Page 58
APXTM 7500 O5
58
Index
Emergency Operation
Sending an Emergency Alarm with Emergency Call
This feature allows you send an Emergency Alarm to
another radio. Upon acknowledgement, both radios can
communicate over a preprogrammed Emergency
channel.
If the radio has both emergency call and alarm features,
it automatically proceeds to the call mode after the
alarm is acknowledged.
1 Press the preprogrammed Emergency button to
activate the emergency call/alarm feature.
2 The display alternates EMERGENCY and the home
display.
3 A high-pitched tone sounds, indicating that the alarm
has been received by the trunked system’s central
controller.
A dispatcher acknowledgment (four high-pitched
tones) follows, accompanied by an ACK RECEIVED
display.
4 Hold the microphone vertically 1 to 2 inches (2.0 to 2.5
cm) from your mouth.
5 Press and hold the PTT button. Speak clearly into the
microphone.
6 Release the PTT to end the transmission.
7 Press and hold the preprogrammed Emergency button
until a tone sounds to exit Emergency mode.
Volume Knob
Home
Button
Menu Select Button *
Emergency
Page 59
APXTM 7500 O5
59
Index
Emergency Operation
Special Considerations for Emergencies
• If you press the emergency button while in a channel
that has no emergency capability, a low-pitched tone
sounds.
• If the unit is out of the range of the system and/or the
emergency alarm is not acknowledged, a tone sounds
and the display shows NO ACKNOWLEDGE.
• If you press the emergency button, then change to a
mode that has no emergency capability, the display
shows NO EMERGENCY and a continuous low pitched tone sounds until a valid emergency mode is
selected or until the emergency is cancelled.
• When an emergency is active, changing to another
mode where emergency is enabled (trunked or
conventional) causes an emergency alarm and/or
emergency call to be active on the new mode.
Volume Knob
Home
Button
Menu Select Button *
Page 60
APXTM 7500 O5
60
Index
Secure Operations
Secure Operations
Secure radio operation provides the highest
commercially available level of voice security on both
trunked and conventional channels.Unlike other forms of
security, Motorola digital encryption provides signaling
that makes it virtually impossible for others to decode
any part of an encrypted message.
Berks County’s talkgroup are strapped to clear, or
Encrypted. The Secure/Clear switch is not
programmed. In the case of Encrypted, the talkgroups
can be either strapped to an AES or ADP key. If needed
a list of these Talkgroups can be found in the master
fleetmap document provided earlier.
NUIS PRFL ZONE SCAN SCNL
Navigation
Button
Volume Knob
Home
Button
Menu Select Button
Channel Knob
Dim Button
NUIS PRFL ZONE SCAN ScnL
Page 61
APXTM 7500 O5
61
Index
Trunking System Controls
Using the Failsoft System
The failsoft system ensures continuous radio
communications during a trunked system failure. If a
trunking system fails completely, the radio goes into
failsoft operation and automatically switches to its
failsoft channel.
The failsoft condition is indicated by a faint beeping tone
every nine seconds (radio unquenched) until the
trunking system returns to normal operation.
To continue, in Failsoft, to communicate with other
talkgroups, refer to the following procedure.
1 Rotate the Channel Knob to change to a different
repeater frequency.
2 Press the PTT button to talk, and release the button to
listen.
When the trunking system returns to normal operation,
your radio automatically leaves failsoft operation and
returns to trunked operation.
Navigation
Button
Volume Knob
Home
Button
Channel Knob
Menu Select Button
Failsoft
NUIS PRFL ZONE SCAN SCNL
Page 62
APXTM 7500 O5
62
Index
Trunking System Controls
Going Out-of-Range
OUT OF RANGE when your radio goes out of the range
of the system, it can no longer lock onto a control
channel.
1 A low-pitched tone sounds.
AND/OR
The display shows the currently selected zone/
channel combination and OUT OF RANGE.
2 Your radio remains in this out-of-range condition until:
It locks onto a control channel.
OR
It locks onto a failsoft channel.
OR
It is turned off.
Navigation
Button
Volume Knob
Home
Button
Channel Knob
Menu Select Button
Out of range
NUIS PRFL ZONE SCAN SCNL
Page 63
APXTM 7500 O5
63
Index
UTILITIES
Viewing the Recent Calls ......................................................
Selecting a Radio Profile .......................................................
Controlling the Display Backlight ........................................
Turning Keypad Tones On or Off .........................................
Using the Time-Out Timer .....................................................
Using the Digital PTT ID Feature ..........................................
Accessing the General Radio Information ..........................
Voice Announcement ............................................................
Page 64
APXTM 7500 O5
64
Index
Utilities
Viewing Recent Calls List
This feature allows you to view the recent incoming and
outgoing call information of the following call types:
• Call Alert
• Selective Call
• Private Call
• Phone Call (Outgoing only)
Note: The radio can also be preprogrammed to log only
the radio IDs associated with incoming Dispatch Calls.
Check with your dealer or system administrator for more
information.
1 to RCNT.
2 Press the Menu Select button directly below RCNT
to access the Recent Calls feature screen.
3 to scroll through the list.
4 Press the Menu Select button directly below BACK
to return to Home screen.
OR
Press or the PTT button to return to the Home
screen.
The radio automatically exits the feature, if the time-out
timer is enabled, when the radio is left idle and the timer
expires. You will hear the Menu Inactive Exit Tone upon
feature exit.
Navigation
Button
Volume Knob
Home
Button
Channel Knob
Menu Select Button
Menu Select Items
Nuis Prfl Zone Scan ScnL
Mute Info Rcnt Colr Cnts
Myid
MUTE INFO RCNT COLR CNTS
Page 65
APXTM 7500 O5
65
Index
Utilities
Selecting a Radio Profile
This feature allows you to manually switch the visual
and audio settings of the radio. The display, backlight,
alert tones, and audio settings are defined according to
the preprogrammed radio settings of each radio profile.
You can have up to a maximum of twelve (12) radio
profiles programmed into your radio by a qualified radio
technician.
Note: The radio automatically exits the feature, if the
time-out timer is enabled, when the radio is left idle and
timer expires. You will hear the Menu Inactive Exit Tone
upon feature exit.
1 to PRFL.
2 Press the Menu Select button directly below PRFL to
access the Profiles feature screen.
3 to scroll through the menu selections.
4 Press the Menu Select button directly below SEL to
select the required radio profile.
OR
Press the Menu Select button directly below EXIT to
exit the screen without making any changes.
5 The radio returns to the Home screen. The profile
name on the Home screen indicates the current
selected radio profile.
Navigation
Button
Volume Knob
Home
Button
Channel Knob
Menu Select Button
Menu Select Items
Nuis Prfl Zone Scan ScnL
Mute Info Rcnt Colr Cnts
Myid
NUIS PRFL ZONE SCAN SCNL
Page 66
APXTM 7500 O5
66
Index
Utilities
Controlling the Display Backlight
You can enable or disable the radio’s display backlight
as needed, if poor light conditions make the display
difficult to read.
Depending on how your radio is preprogrammed, you
can also maintain a minimum backlight level on the
radio’s display.
Note: The backlight setting also affects the Menu Select
buttons, the Menu Navigation buttons and the keypad
backlighting accordingly.
Press the button to toggle the backlight off or on.
OR
Press any key of the keypad, the Menu Select or Menu
Navigation buttons, or any programmable radio controls
or buttons to turn the backlight on.
Volume Knob
Home
Button
Menu Select Button *
Page 67
APXTM 7500 O5
67
Index
Utilities
Turning Keypad Tones On or Off
You can enable and disable keypad tones if needed.
Press the preprogrammed Keypad Mute button to turn
the tones off or on.
OR
1 to MUTE.
2 Press the Menu Select button directly below MUTE.
3 The display momentarily shows TONES OFF,
indicating that the keypad tones are disabled.
OR
The display momentarily shows TONES ON, and a
short tone sounds, indicating that the keypad tones
are enabled.
Navigation
Button
Volume Knob
Home
Button
Channel Knob
Menu Select Button
Menu Select Items
Nuis Prfl Zone Scan ScnL
Mute Info Rcnt Colr Cnts
Myid
MUTE INFO RCNT COLR CNTS
Page 68
APXTM 7500 O5
68
Index
Utilities
Using the Time-Out Timer
This feature turns off your radio’s transmitter. You
cannot transmit longer than the preset timer setting.
If you attempt to do so, the radio automatically stops
your transmission, and you hear a talk-prohibit tone.
The timer is defaulted at 60 seconds, but it can be
preprogrammed from 3 to 120 seconds, in 15-second
intervals, or it can be disabled entirely for each radio
mode, by a qualified radio technician.
Note: You will hear a brief, low-pitched, warning tone
four seconds before the transmission times out.
1 Hold down the PTT button longer than the
preprogrammed time. You hear a short, low-pitched
warning tone, the transmission is cut-off, and the
LEDs goes out until you release the PTT button.
2 Release the PTT button. The LEDs relight and the
timer resets.
3 Press the PTT button to re-transmit. The time-out
timer restarts and the red LED lights up.
Navigation
Button
PTT
Button
Volume Knob
Home
Button
Channel Knob
Menu Select Button *
Page 69
APXTM 7500 O5
69
Index
Using the Digital PTT ID Feature
UTILITIES
This feature allows you to see the radio ID (number) of the
radio from whom you are currently receiving a transmission.
This ID, consisting up to a maximum of eight characters, can
be viewed by both the receiving radio and the dispatcher.
Your radio’s ID number is also automatically sent every time
the PTT button is pressed. This is a per-channel feature.
For digital voice transmissions, your radio’s ID is sent
continuously during the voice message
.
Accy No-Dot
Button (Purple)*
Accy 1-Dot Button*
Accy 2-Dot Button*
PTT
Page 70
APXTM 7500 O5
70
Index
Utilities
Accessing General Radio Information
Viewing IP Information
This feature displays the device name, IP address, and
status of your radio.
Note: The device name of your radio is preprogrammed.
Check with your dealer or system administrator for
more information.
Press the preprogrammed Info button and proceed to
Step 3.
OR
1 to INFO.
2 Press the Menu Select button directly below INFO.
3 to IP INFO and press the Menu Select
button directly below SEL.
4 to scroll through the various information.
OR
Press the Menu Select button directly below BACK
to return to previous screen.
OR
Press to exit and return to the Home display.
Navigation
Button
Volume Knob
Home
Button
Channel Knob
Menu Select Button
Menu Select Items
Nuis Prfl Zone Scan ScnL
Mute Info Rcnt Colr Cnts
Myid
MUTE INFO RCNT COLR CNTS
Page 71
APXTM 7500 O5
71
Index
Utilities
Accessing General Radio Information
Accessing Radio Information (2/2)
1 to INFO.
2 Press the Menu Select button directly below INFO.
3 to RADIO INFO and press the Menu
Select button directly below SEL.
4 The display shows the Information screen.
5 to scroll through the various information.
OR
Press the Menu Select button directly below BACK
to return to previous screen.
OR
Press to exit and return to the home display.
Navigation
Button
Volume Knob
Home
Button
Channel Knob
Menu Select Button
Menu Select Items
Nuis Prfl Zone Scan ScnL
Mute Info Rcnt Colr Cnts
Myid
MUTE INFO RCNT COLR CNTS
Page 72
APXTM 7500 O5
72
Index
Utilities
Changing the Display Color
You can change or the radio’s display color as needed.
1 Press to COLR.
2 Press the Menu Select button directly below COLR.
3 Press to scroll through the list of available
choices.
4 Press the button below SEL to select the color or
CNCL to exit without making changes.
***NOTE: If you change the display to “RED” when the
radio is “out of range” the display will not change
colors.
If you change the display to “ORANGE” and activate
the “emergency button” the display will not change
colors.
Navigation
Button
Volume Knob
Home
Button
Channel Knob
Menu Select Button
Menu Select Items
Nuis Prfl Zone Scan ScnL
Mute Info Rcnt Colr Cnts
Myid
MUTE INFO RCNT COLR CNTS
Page 73
APXTM 7500 O5
73
Index
Utilities
Voice Announcement
This feature enables the radio to audibly indicate the
current feature mode, Zone or Channel the user has just
assigned. This is typically useful when the user is in a
difficult condition to read the content shown on the
display. A maximum of 2000 unique voice
announcements are allowed in a radio. The sum total
duration for all voice announcements in a radio shall be
no more than 1000 seconds.
The features which Voice Announcement supports are:
• Zone
• Channel
• Scan
Loading...