Mota Jetjat Nano-c User Manual
AGES 8+
OWNER’S
MANUAL
JETJAT NANO - C
For Owner’s Manual updates, warranty information, and support, please visit:
go.mota.com/62
Product Number: 0609456616072, 0609456616089
Product Model:JJ-NANC-K, JJ-NANC-R
Table of Contents
Fly Safely
In the Box
Battery Installation and Charging
Charging the JETJAT Nano-C
Operation and Control
Response Levels
Aerial Tumbling
Photo and Video
Trim Adjustment
Accelerometer Calibration
Low Battery and Standby Function
Troubleshooting Tips
Specifications
Lithium Battery Safety Guide
Fly Safely
Drones are sophisticated precision devices capable of complex aerial maneuvers. Please
read these safety instructions before using your drone. Failure to operate your drone
safely could degrade its performance and cause harm to people, animals, or property.
Please do not fly:
- Near or around obstacles such as birds or pets, aircraft, helicopters, other drones,
antennas or overhead lines, or airborne toys lke kites.
- In or near airports or restricted areas.
- In adverse conditions such as strong winds, rain, hail, snow or sleet.
3
4
6
6
7
8
9
9
10
10
11
11
12
13
- If you are impaired, tired, or distracted.
Please do:
- Know and comply with laws and regulations respecting drone use in your area.
- Keep hands away from rotors when drone is switched on.
- Fly within transmitter range, which is 75 feet.
Download your
SAVE-A-DRONE
Flight Safety Poster
@ mota.com/jetjat
USB CHARGING CABLE
PROPELLER GUARD
QUAD COPTER
Micro
(available）
USB
In the Box
BLADE
MICRO SD CARD
TRANSMITTER
Power
Battery Installation and Charging
1. Open battery cover 2. Install two “AAA” batteries 3. Close cover
Note: Check that both batteries’ positive
and negative terminals are installed correctly.
Charging the JETJAT NANO-C
START UP
1. Turn ON the transmitter.
2. Pull the throttle all the way back toward the user.
(Figure 1) The transmitter will beep once.
3. Turn ON the drone and place it on a level surface.
Its lights will ash.
4. Push the throttle all the way forward, away from the
user. (Figure 2)
5. Pull the throttle all the way back toward the user. The
drone’s lights will stop ashing.
Caution: Please operate the control stick slowly when ying your drone. During ying, the
drone may lose altitude when maneuvering. Therefore, you may need to add more power
to keep the drone ying at a given height.
- Throttle: Ascent and Descent
- Direction: Left and Right Rotation
- Rudder: Fly Forward or Backward
- Aileron: Fly Left or Right
Operation and Control
Response Levels
Press the left throttle down to traverse through three control levels.
Moderate: Single “beep” - moderate control responsiveness
High: Double “beep”- high control responsiveness
Maximum: Triple “beep” - highest control responsiveness
Aerial Tumbling Trim Adjustment
JETJAT Nano-C can do aerial flips.
- Flips can be performed in any one of 4 horizontal directions: left, right, forward,
or backward.
- In order to better carry out aerial flips, ensure the drone is at least one meter
above the ground.
- To perform flips, first press the right throttle. A single “beep” from the
transmitter signals the drone is in flip mode.
Once in flip mode:
Left Flip: Push the aileron to the left.
Right Flip: Push the aileron to the right.
Front Flip: Push the ascend/descend throttle forward.
Back Flip: Push the ascend/descend throttle back.
Photo and Video
Video:
To Start Recording: Once the drone and transmitter are paired, briefly press the
video switch on the transmitter. The blue Video-Photo indicator light on the drone
will flash quickly.
To Stop Recording: When recording, briefly press the Video switch on the
transmitter. The Video-Photo indicator light on the drone will turn a steady blue
indicating recording has finished.
Photos:
Once the drone and transmitter are paired, briefly press the Photo switch on the
transmitter. The blue Video-Photo indicator light on the drone will flash quickly
twice. This signals that the camera has stored a photo on the Micro SD Card
Left Flying
Left Flying
trimmer
Right Flying
trimmer
trimmer
Right Flying
trimmer
Accelerometer Calibration
If the drone appears unstable or drifts to one direction, you need to calibrate the
accelerometer.
1. After pairingthe drone and transmitter, place the drone on a level surface.
2. Set Sensitivity to Maximum and pull the throttle all the way back and left
while pushing the ascend/descend aileron all the way forward to the upper left.
The drone’s main lights will flash for 1-2 seconds, indicating that the calibration
was successful.
Note: If the drone still drifts in one direction, you may need to compensate for the accelerometer’s
horizontal angle of deviation. Re-pair the drone and transmitter if necessary, then place the drone on a
level surface with several sheets of paper under the rotor facing the direction of the ight. Then
re-calibrate the accelerometer.
Low Battery Voltage
When the battery voltage is running low, the four LED indicators on the drone will
flash. Lower the flying height and land the dron as soon as possible to avoid
damaging the drone. Turn off the drone power and recharge.
Standby Function
After about 8 minutes of inactivity, the drone will automatically turn off. To turn on
the drone, move the Power Switch to the OFF and then ON positions. The LED
lights will indicate that it is turned on.
Rotors not functioning properly.
Drone will not take off.
Auto Shut-Off Protection:
If the rotors are obstructed during
operation, the drone will shut-off.
3 4 5 6 7 8 9 10 11
Low Battery and Standby Function
TROUBLESHOOTING TIPS
PROBLEM STEPS
Turn the drone OFF, then ON and
pair with the transmitter. Replace
the propellers if deformed,
damaged, or installed incorrectly.
How:
1. Grasp propeller underneath
center cap where it meets drone
body.
2. Pull straight off its shaft.
Check that the drone is fully
charged. If necessary, check
Accelerometer calibration.
Clear the obstruction. Turn the
drone OFF, then ON. Check that
the drone is fully charged.
Specifications
Dimensions
L x W x H: 32 x 32 x 22 mm
Weight: 0.6 oz
Camera: 0.3 megapixels
Range: Approximately 75 feet
Flight Time: Approximately 2.5 to 4 minutes
Charging Time ( 120 mAh, 3.7 V): Approximately 25 minutes
Note: Flight time, range and charging time may vary depending on ight conditioins and battery condition.
12 13
Lithium Battery Safety Guide
If the device is not operating, charging the lithium battery may cause re, injury, or
loss of property. The user should be aware of the risks while using the product. The
manufacturer shall not in any way be liable to you or to any third party for any
damages you or any third party may suffer as a result of use, intended or
!
WARNING:
Your drone uses an internal high-performance non-removable lithium battery. The transmitter uses 2 AAA
replaceable batteries. Please store the drone and batteries in a cool, dry environment away from children
and pets.
1. Do not disassemble, pierce, cut, or distort the drone or its batteries. Doing so is a safety hazard and
violates the warranty.
2. Please use the only original USB charger cable included with the drone.
3. When charging, ensure the drone is in a ventilated area, on a hard surface and uncovered, and do not
leave it unattended more than a few minutes. The drone automatically stops charging after the battery is
full (you will see the red light on the USB connector turn OFF) but it is recommended you disconnect the
power source once your drone is charged.
4. Do not y or store the drone in very high temperatures or near any heat source, open ame, or
ammable materials.
5. Metal objects may cause a short in the battery if they touch its positive (”+”) and/or negative (”-”)
terminals. Please do not store or transport the drone and transmitter with metallic objects of any kind such
as coins, keys, thumb drives, etc.
6. In the unlikely event the drone or transmitter’s batteries emit an odor, smoke or liquid, or if you notice
any other abnormal condition, immediately disconnect the drone from the charging device (if connected)
and take the drone and transmitter outdoors to a safe area. Do not attempt to charge, operate or switch the
drone transmitter ON or OFF. Do not touch any liquids as it may irritate the skin. If liquid from a battery
accidentally gets into an eye, rinse the eye with clear water. If irritation persists, seek medical attention.
7. When the batteries reach the end of their useful life. please dispose of the drone and transmitter
batteries at an authorized recycling center or organization.
This product carries a 90-day Limited Warranty against defects in materials and workmanship. The Limited
Warranty is valid only if defect(s) are reported to MOTA Technical Support before the drone’s rst ight.
MOTA is not responsible for any damage to the product and/or accessories other than defects in materials
and workmanship. MOTA is not responsible for any indirect or consequential damages or liability arising
from use of the product by the owner or others. This Limited Warranty has additional terms, conditions,
and exclsuions which may be read at www.mota.com/support.
unintended. Please carefully read these safety guidelines and charging
instructions before use.
MOTA guarantees quality materials and workmanship for this product. Under no circumstances
will MOTA compensate an amount higher than the valued retail price.
Lithium Battery Guarantee
Warranty
Loading...