Moog AP8CH2-B Specsheet
HOUSING
ENCLOSURES_
AD8/AP8
AD16/AP16
AD/AP8C-9,
AD/AP16CH2, AP16CH1
Outdoor Tubular
Dustproof & Pressurized Environmental Housings
Moog Videolarm’s AD8CH2 and AP8CH2 units provide a compact camera solution for harsh environments. The units are constructed
with a sealed tubular housing made from a thick aluminum that offers outstanding protection for the camera from dust, moisture,
insects, and pollution. The pressurized and dustproof housing cameras can be adjusted without breaking the housings seal, RS232
connection. Moog Videolarm has equipped the AD8CH2 & AP8CH2 with a xed high resolution color 23x (Vari-Focal Lens), auto-focus
day/night camera (also available in an IP model).
Key Features
•
•
Integrated heater/defogger
•
8” pressurized or dustproof tubular housing
•
Multi-pin, corrosion resistant connectors
•
Control with RS232 input via a Windows based laptop using
software provided
•
MCL 8”
24VAC input
•
Non-volatile memory stores all settings in the event of a
power loss
•
Future enhancements include control via PDA and RS485
control with Moog Videolarm and other manufacturer’s
protocols. Call Moog Videolarm for more information.
CERTIFIED
AD/AP8C-9, AD/AP16CH2, AP16CH1_
© 2009-2010, Moog Videolarm, Inc. All Rights Reserved
Product and company names listed are trademarks or trade names of their respective companies.
Fixed Tubular Camera Housing:
AD8C-9
Dust proof outdoor housing, 24VAC input.
Three liquid tight ttings for wiring
AP8C-9
Pressurized outdoor housing, 24VAC input
SPECIFICATIONS:
Camera Specications
Image Sensor:
Output:
Number of Effective Pixels:
Resolution:
Lens:
Digital Zoom:
Angle of View:
Minimum Illumination Color:
B&W:
S/N ratio:
Electronic Shutter:
White Balance:
Automatic Gain Control:
Iris Control:
Backlight Compensation:
Focusing System:
Low Light IR Mode:
Privacy Zone:
Environmental Specications
Operating Temperature:
Electrical Specications (AD-AP8C-9)
Power Input:
Power Consumption:
Electrical Specications (AD-AP16CH2)
Power Requirements:
Camera:
Heater:
Total:
¼” interline transfer CCD
NTSC
Approx. 380,000 pixels
470 (H) x 400 (V) TV lines
23x optical (f=3.6mm - 82.8mm)
10x (230x with optical zoom)
(H) 54° (wide) to 2.5° (tele)
3 lux @ 1/60s, .2 lux @ 1/4s
0.02 lux (1/4s, IR cut lter removed)
50 dB
Auto/Manual (manual 1/2s - 1/30000s)
Auto/Manual
Auto/Manual (-3 to 28 dB, 16x 2 dB steps)
Auto/Manual
On/Off
Auto/Manual
Auto/Manual
On/Off
-40º F to 122º F (-29° C to 49° C)
24VAC, 50/60 Hz
18W (750mA)
24VAC
Power Consumption
5W (208mA)
10W (417mA)
15W (625mA)
Tubular Camera Housing:
AP16CH2
16” dust-proof tubular housing, 24VAC input.
Includes an integrated heater/defogger MCL 16”
(Maximum Camera Length)
AP16CH1
Pressurized outdoor housing,115VAC input
AD16CH2
Dust proof outdoor housing with heater, 24VAC input
AD8C-9:
AP8C-9:
AD16CH2:
AP16CH2:
ACCESSORIES:
VLAY8
Sunshield
Engineering Specications
The AD8C-9 environmental, dust free housing is constructed from .16” (4mm) thick aluminum.
The camera housing is designed to prevent dust from entering the unit. Chemically strengthened
glass has been used for the faceplate. Three liquid tight ttings (2 NPT 1/2” and 1 NPT 3/8”) are
included for cable entry. The camera has a xed high resolution color with 23x zoom, auto iris lens.
The camera has a horizontal resolution of 470 horizontal TV lines. Input power 24VAC. A camera
cradle assembly allows easy installation and access to the camera and internal equipment. An
integral heater/defogger is standard in each unit and is mounted to the camera cradle to allow heat
transfer to the window to minimize fogging in high humidity and/or freezing under cold temperature
conditions. The temperature range -40˚ F to +120˚ F. An aluminum sunshield is available as a
separately boxed items. This unit is FCC Part 15 approved.
The AP8C-9 environmental, pressurized housing is constructed from .16” (4mm) thick aluminum.
The camera housing has been sealed on both ends by radial pressure O-rings to create a tight
seal. Front to back motion is prevented by a retaining ring in the front and screws in the back.
Chemically strengthened glass has been used for the faceplate. The housings contain a single
corrosion resistant connector for power, video, and external sync, and a mating connector is
provided for the camera. The xed high resolution color camera has a 23x zoom, auto iris lens.
The camera has a horizontal resolution of 470 horizontal TV lines. Input power 24VAC. A camera
cradle assembly allows for easy installation and access to the camera and internal equipment. The
housings is tted with a standard Schraeder valve for pressurization with 5 lbs. positive pressure of
dry nitrogen. An over pressurization safety relief valve has been mounted on each unit. An integral
heater/defogger is standard in each unit mounted to the camera cradle to allow heat transfer to the
window to minimize fogging in high humidity and/or freezing under cold temperature conditions.
The temperature range -40˚ F to +120˚ F. An aluminum sunshield is available as a separately boxed
items. This unit is FCC Part 15 approved.
The VideoKit™ AD16CH2 environmental, dust free housing is constructed from .16” (4mm) thick
aluminum. The camera housing is designed to prevent dust from entering the unit. Chemically
strengthened glass used for the faceplate. Three liquid tight ttings (2 NPT 1/2” and 1 NPT 3/8”)
is included for cable entry. A xed high resolution color camera included, and features an auto iris
5-50mm lens. A camera cradle assembly is included to allow easy installation and access to the
camera and internal equipment. An input power of 24VAC. An integral heater/defogger is standard
in each unit and is mounted to the camera cradle to allow heat transfer to the window to minimize
fogging in high humidity and/or freezing under cold temperature conditions. The temperature range
shall be -40˚ F to +120˚ F. An aluminum sunshield is available as a separately boxed items.
The AP16CH2 environmental, pressurized housing shall be constructed from .16” (4mm) thick
aluminum. The camera housing shall be sealed on both ends by radial pressure O-rings to create
a tight seal. Front to back motion shall be prevented by a retaining ring in the front and screws
in the back. Chemically strengthened glass shall be used for the faceplate. The housings shall
contain a single corrosion resistant connector for power, video, and external sync, and a mating
connector shall be provided for the camera. A camera cradle assembly shall be included to allow
easy installation and access to the camera and internal equipment. The housings are tted with
a standard Schraeder valve for pressurization with 5 lbs. positive pressure of dry nitrogen. An over
pressurization safety relief valve shall be mounted on each unit. An integral heater/defogger shall
be standard in each unit and shall be mounted to the camera cradle to allow heat transfer to the
window to minimize fogging in high humidity and/ or freezing under cold temperature conditions.
The temperature range shall be -40˚ F to +120˚ F. An aluminum sunshield shall also be available as
a separately boxed items.
VLAY16
Sunshield
WM1600
Wall Mount for all
tubular housings
500-702 + 06-24-2010
Moog Videolarm, 2525 Park Central Boulevard, Decatur, GA 30035 USA + 1.800.554.1124 www.videolarm.com
Loading...