Page 1
Model #: EZ1 AUS, NZ
MONSTER CLASSIC FLOOR STEAMER (EZ1)
INSTRUCTION MANUAL
S
t
e
a
m
B
o
o
s
t
e
r
Page 2
SAVE THESE INSTRUCTIONS
SAFETY WARNING
• The manufacturer reserves the right to make changes to the design and features of
the appliance without notice.
• This appliance is solely for household use.
• Do not turn the appliance on if the steam mop shows signs of damage, the power
cable is damaged or if the appliance has been potentially subject to non-identiable damage (e.g. the appliance as been dropped, etc.).
• Do not plug in the appliance until you are sure the electrical voltage supply cor-
responds to the required voltage shown on the machine plate.
• The electric socket should be earthed and equipped with a 10A automatic circuit
breaker.
• Any extension cables should be checked to ensure they are rated 10A and suitable
for the appliance. Cables should be completely unwound prior to use.
• The appliance should not be used if there are visible signs of damage or leakage.
• The manufacturer declines any responsibility for damage to persons or equipment,
in the event that the equipment is damaged as a result of improper use, unauthor-
ized repair or unauthorized maintenance work.
• Repairs should be carried out solely by personnel authorized by the manufacturer.
Equipment repaired by personnel who are not authorized to do so, represent a risk
and, as such, are not covered by the warranty.
• The power cable should only be replaced by technical support personnel who
have been authorized by the manufacturer.
• Do not use the appliance outdoors.
• Do not expose the appliance to external atmospheric agents, dampness or heat.
• Use a dry or slightly damp cloth to clean the appliance.
• Use solely manufacturer-recommended accessories or spare parts.
• The steam released from the appliance is extremely hot. Both appliance and accessory tools may scald. Avoid direct contact. The steam symbol (symbol 5597
relative to IEC 60417-1) warns operators that there is the risk of scalding!
• This appliance is not suitable for children, the physically or mentally disabled, or
persons without the necessary experience and know-how to handle the machine,
unless they have been adequately trained by safety personnel.
• Keep out of the reach of children.
• Keep the appliance in a safe dry place out of the reach of children when not in use.
• Do not pull on the cable. Do not use the cable to move the appliance. Do not exert
undue pressure on the cable (i.e. when closing a door). Avoid any contact with
sharp edges and corners. Keep the cable away from hot surfaces.
• No parts connected to an electrical power supply (switch, plug, electronic components, etc.) should be in contact with water.
• Disconnect the appliance from the power supply prior to any maintenance or
cleaning operations. Allow the steam mop to cool down.
• Do not leave the equipment unguarded. Remove the power supply in the event the
machine remains unattended for a period of time.
• Never use cleaning solutions, perfumes, oils or other chemical substances other
than tap or distilled/demineralized water in the Steam Cleaner. Use of chemicals
may damage appliance and will void your warranty.
• Do not overturn or lean the appliance unduly to one side.
• Do not point the jet of steam in the direction of people, animals, plants, electrical or
household appliances.
• Do not insert any objects in the various openings and do not use the appliance if
any opening is obstructed.
• Do not use the appliance with wet hands or bare feet.
• Do not use the appliance when close to ammable or explosive substances.
IMPORTANT SAFE TY INSTRUCTIONS
2
Safety Instructions
Page 3
SAVE THESE INSTRUCTIONS
Please contact your closest technical support centre should you require further infor-
mation or instructions not contained in this document.
Customer Support Centre:
Australia: 1800 663 866
New Zealand: 0800 666 783
Dispose of plastic packaging appropriately, as it may represent a potential hazard for
children!
IMPORTANT: Before operating the unit for the rst time, read these instructions carefully
and keep them for future reference.
Euroex relieves itself of any liability for damages that shall be the result of improper
use of the appliance, not in conformity with what’s written in this instruction manual.
WARNING: This appliance must be earthed.
The appliance must be connected to a 220-240 volt 50/60Hz AC supply by means of a
three pin socket, suitably earthed.
3
Safety Instructions
*IMPORTANT*
Please read all of the
instructions for use and
Important Safety
Instructions carefully.
Remove and discard all
packaging materials
and keep them out
of the reach of children.
CAUTIONS
•
Do not use your Floor Steamer without a Hard Surface Pad or Carpet Glide
& Pad attached to the system.
• Never leave your Floor Steamer in one spot on any surface for any period
of time. Always place on the Parking Pad and make sure that the Floor
Steamer Handle Assembly is in the full “UP POSITION” when not in use - this
turns the Steamer Off.
Save your back
No need to
press hard
The steamer
does the
work for you
Page 4
One (1) Floor Steamer
1
4
6
3
7
10
2
1 - Cord Winder
2 - Handle
3 - Metal Extension Tube
4 - Measuring Cup (pre-marked)
5 - Filling Funnel
6 - Boiler Cap
7 - Steam Ready Indicator Light
(green)
8 - Power Indicator Light
(orange)
9 - Power Cord
10 - Steam Nozzles
11 - Hard Surface Floor Pad
12 - Carpet Pad
13 - Carpet Glide
14 - Parking Pad
Product Features
4
Product Features
9
8
Technical Data
Adapter Input: 220-240V~, 50/60Hz
Cord Length: 7 meters/23 feet
Power: 1200 watts
Boiler: Stainless Steel
Boiler Capacity: 0.6 liter/20 ounces
Steam Pressure: 3.5 bars
PARKING PAD
14
13
12
11
5
Page 5
Before Use
5
Before Use
Assembly of Parts & Preparation of Steamer
Make sure all parts are in the box (see pg 4).
IMPORTANT: FOLLOW THESE INSTRUCTIONS CAREFULLY!
1
*IMPORTANT*
Frontal steam can only be generated when Extension Tube is in the
“Maximum Extension” position.
BE SURE EXTENSION TUBE IS FULLY
EXTENDED AND LOCKED IN PLACE FOR OPTIMAL STEAM OPERATION.
“Maximum Extension” Position
• Snap connector down. When a “click” is heard, the Tube is locked in position.
• Extend Tube to the
“Lock - I” position.
LOCK
CLICK!
Pull apart Extension Tube
A. Assemble Handle
After removing Handle Assembly from carton:
• Pull Extension Tube apart (shown below).
Page 6
6
Before Use
Before Use
B. Attach Handle to Steamer
• Before starting, remove the self-tapping screw from the bottom of
Extension Tube.
• Insert the Handle Assembly into the Floor Steamer Base. Align
Arrow on Handle with Arrow on Base (as shown in Fig. A).
• Once inserted, twist Handle Assembly 90° clockwise (as shown
in Fig. B). Be sure Arrow on the Handle is aligned with Line/Lock Icon
on Base.
• Align the Handle Assembly
screw hole with the opening
in the steamer housing.
Secure the handle assembly
with self-tapping screw which
was removed from bottom of
Extension Tube (as shown in
Fig. C).
Fig. A
Fig. B
Fig. C
Front View Side View
90°
Page 7
7
Before Use
C. Attach Hard Surface Floor or Carpet Pad to Steamer
Afx either the Hard Surface Floor Pad or Carpet Glide with
Carpet Pad to your Floor Steamer.
WARNING:
To prevent oor damage, ALWAYS attach either the
HARD SURFACE FLOOR PAD or the CARPET GLIDE ACCESSORY with
CARPET PAD when using your Floor Steamer. NEVER use without
either of these attachments afxed to the machine.
ATTACHING HARD SURFACE FLOOR PAD
Place Floor Pad face down on the oor, with
white hook and loop strips facing up. Hold Floor
Steamer about 2” above Pad and gently place
Floor Steamer onto the Pad. Firmly press down
to ensure Pad is securely adhered to the Floor
Steamer.
ATTACHING CARPET GLIDE WITH CARPET PAD
Place Carpet Glide face up on oor. Center
and place Carpet Pad on top of Carpet
Glide. Hold Floor Steamer over Carpet Glide and
gently lower the Steamer onto the Glide. Make
sure the 4 clips on Glide are around the outside
of the Steamer Base and using hands, attach the
4 clips of the Carpet Glide to the Steamer Base.
USE ON HARDWOOD FLOORS
For hardwood oors, use only on “sealed”
hardwood surfaces. Move Steamer forward and
backward while cleaning, carefully observing
the amount of steam used, as too much water
could cause damage.
Before Use
IMPORTANT NOTE ABOUT LINOLEUM FLOORING
Steam can cause wax to be stripped from, and consequently damage,
some varieties of linoleum ooring. ALWAYS test a small, inconspicuous
portion of the oor BEFORE using steam to ensure that your linoleum
oor does not have this issue.
NOTE: See “Maintenance & Cleaning” (page 13) for care and cleaning instructions
for Microber Pads.
Page 8
Before Use
8
Before Use
*IMPORTANT*
• Do not overll the Boiler as excess water will be ushed out of the Boiler
before dry steam will emit.
• If re-lling the Boiler while Steamer has been in use, be sure to allow
Steamer to cool for at least 5 minutes and loosen Boiler Cap slowly to
allow any excess steam to escape before completely removing Cap.
(See page 10, “Relling Boiler During Use” for detailed instructions.)
D. Filling Boiler with Water
WARNINGS:
•
Carefully read all instructions before removing Boiler Cap.
•
Always unplug appliance before lling the Boiler.
Follow these instructions to avoid overlling
the Boiler.
• Be sure appliance is unplugged from the
electrical power outlet, and has
cooled for
at least 5 minutes before lling with water.
• Make sure Handle Assembly is in the
upright “off” position.
Remove Boiler Cap
by turning it counterclockwise.
• Pour in 600 mls of water using
the Measuring Cup and Filler
Funnel provided – ll cup to the
“200 ml” marking three times.
Be careful not to overll the
Boiler.
Please note that excess
water will be ushed out during
use if the Boiler is overlled,
resulting in wet oors.
• Replace Boiler Cap by turning it clockwise.
Do not tighten Boiler Cap too much – nger
tightening is sufcient to lock the steam in the Boiler.
If using cold water, heating time is about 3-5 minutes. If using warm
water, heating time is reduced.
*IMPORTANT*
Use ordinary tap water. Distilled or demineralized water is
recommended if tap water is too hard.
DO NOT add detergents,
perfumes, oils, or other chemical substances to the Boiler. The
product warranty will be null and void if anything other than water
is added to the Boiler.
100 ml
200 ml
A
N
T
(
M
a
x
100 ml
200 ml
A
N
T
I
B
A
K
(
M
a
x
)
Page 9
9
Using Your Floor Steamer
Using Your Floor Steamer
Using Your Floor Steamer
2
B. Starting the Appliance
• Be sure Boiler is lled with water and Boiler
Cap is securely in place.
• Insert the plug into a-3 prong grounded
electrical outlet (orange Power Indicator
Light will illuminate).
•
Keeping the handle in the upright “Off”
position
, wait until the (green) Steam Ready
Indicator Light illuminates.
Once Boiler is lled and the green Steam
Ready Indicator Light glows, Steamer is ready to clean.
A. Using the Parking Pad
You can use the Parking Pad if the Steamer is warm or hot.
CAUTION
The Parking Pad is provided to prevent
oor damage that can result from leaving
a hot steamer resting on the same spot
for too long. ALWAYS place Floor Steamer
on the Parking Pad when not in use, or
while it is cooling before storage.
PARKING PAD
C. Using Steam
• To emit steam from the
underside of the Steamer,
simply pull the Handle
downwards.
• Return Handle to upright
position to stop steam.
You will nd that your Floor
Steamer can easily clean
most hard surfaces and
oors using the steam from
the underside alone.
NOTE: Some water may be emitted
when the handle is rst pulled
down after lling. This is normal.
Continued on next page
PLEASE NOTE:
The green Steam Ready Indicator Light may turn
on and off during use. This is normal and not a fault.
Page 10
10
Using Your Floor Steamer
Using Your Floor Steamer
• To emit steam from the Steam
Nozzles, pull the trigger on
the Handle upward.
*IMPORTANT*
The Steam Nozzles are meant
to be used in steam “bursts”
and should never be used on
a sustained basis. The Steam
Nozzles will loosen especially
difcult debris and will assist in
cleaning hard to reach areas
such as oor edges.
NOTE:
Your Steamer will not need
relling for about 20-25 minutes
of usage.
The Floor Steamer will stop producing steam when the Boiler is
empty. When this happens unplug and store unit or rell with water
per instructions (below).
NOTE: If the Floor or Carpet Pad becomes too wet or too dirty, replace with a
clean, dry Pad and continue cleaning.
C. Using Steam (continued)
D. Relling Boiler During Use
When the Floor Steamer has run out of water, there will be no more
steam coming out of the unit. At this stage it is time to rell the Boiler.
Follow the relling instructions below.
*IMPORTANT*
The Floor Steamer has a Boiler that should not be overlled. To avoid the
potential for overlling, only rell the Boiler when it is completely run out of
water and only add 600ml. Always follow the practice of using the Floor Steamer
until it has run out of water and then rell 600ml only.
If oor cleaning is completed and water remains in the Boiler, the Floor Steamer
can be stored with the remaining water in the Boiler, there will be no harm done
to the unit. At the next cleaning session simply heat up the unit and use the
water already in the Boiler, then rell when empty.
Or alternatively at the next cleaning session, open the Boiler Cap when the unit
is still cold and pour out the water and then rell (if this alternative method is
used, it is recommended that only 500ml of water is added, because the unit
will not completely drain when the water is poured out from the Boiler).
WARNING: Let Steamer cool 5 minutes before opening Boiler Cap.
Use care when opening Boiler Cap as it may still be hot and steam
may escape, causing burns. If Boiler is still hot, water may spurt out
during relling which can also cause burns.
Page 11
11
Using Your Floor Steamer
•
Unplug the appliance from the electrical power outlet. This will stop
the Steamer from continuing to heat up.
• Once unplugged from the power outlet, place Handle in the “On”
position to release any residual steam and pressure from the Boiler.
• After all steam and pressure has been expressed from the Steamer,
return the Handle to the upright “Off” position.
• Slowly turn Boiler Cap counterclockwise. This will allow remaining
steam to escape.
•
Be sure Steamer has cooled 5 minutes before relling with water.
The product warranty will be null and void if
anything other than water is added to the Boiler.
• Pour in 600 mls of water using the Measuring Cup
and Filler Funnel provided – ll the Measuring
Cup to the 200 ml marking 3 times. Be careful
not to overll the Boiler.
• Replace Boiler Cap by turning it clockwise.
Do not tighten Boiler Cap too much – nger
tightening is sufcient to lock the steam in
the Boiler.
• Insert plug into 3-prong electrical outlet. Wait for
green Steam Ready Indicator Light to turn on. Steamer is ready to use
once again.
100 ml
200 ml
A
N
T
(
M
a
x
*IMPORTANT*
Do not overll the Boiler as excess water will be ushed out of the
Boiler before dry steam will emit.
REMINDERS
• Always use ordinary tap water.
• If tap water is too hard, use distilled or demineralized water to
avoid the risk of mineral deposits and sediment from forming.
• Do not add detergents, perfumes, oils or other chemical
substances to the Boiler. This will damage the Steamer and void the
wa rranty.
• The green Steam Ready Indicator Light may turn on and off during
use. This is normal and not a fault.
Page 12
12
Maintenance & Cleaning
Maintenance & Cleaning
If distilled or demineralized water is regularly used in the
Steamer, cleaning of the Boiler can be done less frequently. In
some areas tap water is very hard, it is recommended that the
Boiler is cleaned more frequently if hard water is used.
The cleaning of the Boiler and Steamer is the sole responsibility of the
appliance owner. Calcium, mineral deposits and other sediment left
to build up in the Floor Steamer causing the Steamer to fail and/or the
steam pathways in the Steamer to block, is not covered by the product
warranty. Users must follow the cleaning instructions above.
If the Steamer and Boiler are not cleaned according to the
instructions above and the product fails and/or the steam
pathways are blocked, the appliance owner should send the
product for servicing by contacting the Customer Support Line.
The Monster Classic Floor Steamer is intended for domestic
household use only. It is not intended for commercial use. Any
use other than for domestic household purposes will void the
product warranty.
Cleaning the Floor Steamer
We recommend you periodically clean the Floor Steamer to prevent
the accumulation of calcium, mineral deposits and other sediment
caused by the use of tap water. After every 10-15 rells, ll the Boiler
three-quarters full of hot tap water, shake several times and empty
out the water into sink. Repeat several times to ensure that the Boiler
is ushed of any calcium or mineral deposits. Wipe the Steamer
base with a damp cloth and dry.
NEVER HOLD THE STEAMER UNDER THE TAP TO FILL. Use the
Measuring Cup and Funnel provided to ll the Boiler.
3
Page 13
13
Troubleshooting
Microber Pad Care & Cleaning
Your Microber Pads are designed for hundreds of uses. Clean Pads
regularly, either by hand (using mild soap and warm water) or in your
clothes washer on a delicate cycle, cool water. Never use fabric
softener or bleach. We recommend letting Pads air dry to maintain
maximum long term effectiveness.
Replacement pads are available at most retail outlets.
Microber washing instructions – ULTRA MICROFIBRE
Maintenance & Cleaning
HARD SURFACE FLOOR PAD
75% Polyester / 25% Polyamide
Hand wash only
Tumble dry low or air dry
No bleach / No fabric softener
CARPET PAD
80% Polyester / 20% Polyamide
Hand wash only
Tumble dry low or air dry
No bleach / No fabric softener
IMPORTANT QUESTION:
Q: Do I always need to use a Microber Pad when cleaning with my
Steamer?
A. YES!
It is critically important to ALWAYS use your Microber Pads. The
Floor Steamer should NEVER be used without either a Hard Surface
Floor Pad or Carpet Glide with Carpet Pad.
Issues Possible Causes Solutions
Steam is not coming out of the Improper Handle assembly. Call Customer Service to receive instructions
Steam Nozzles. to correct the problem.
The Hard Surface Floor Pad Not enough pressure was Position Steamer about 2” above Pad and
is not adhering to Steamer. applied when attaching Pad. FIRMLY press it down onto the Pad.
Floor Pad requires replacing Replacement Floor Pads can be purchased at
due to age of the Floor Pad. most electrical appliance retail outlets.
The Cleaning Pads are getting Boiler is overfilled. Let Steamer run until excess water ceases.
soaked (too wet). Why? -OR- Remove some water from Boiler once
the Boiler has cooled down completely.
Green “Steam Ready Indicator Wait for green “Steam Ready Indicator Light”
Light” is not illuminated. to illuminate.
The steam seems to be Front Steam Jets are being Only use Front Steam Jets in short bursts for
making my floor too wet. used too frequently. cleaning tougher dirt or to clean hard to
reach areas.
The Cleaning Pad is too wet Replace the wet Pad with a dry, clean Pad
(saturated with moisture) and continue cleaning.
Page 14
14
Notes
Notes
Page 15
15
Notes
Page 16
EZ1 (Australia/NZ) 09/27/13
EFLX-039AD
Customer Support
Cu sto me rs n eed in g a ss is ta nc e w it h t he ir M on ste r F lo or Ste am er c an cal l t he Cus tom er
Support Line on the phone numbers listed below. Customers should also call the
Customer Support Line if they require product warranty repair or post-warranty
pro d u ct ser vici ng. Ou r f r iendly Customer Serv i ce Team can a s s i st you with get t i n g the
best cleaning results from your Floor Steamer, they are full of helpful steam cleaning
tips, too.
Monster Customer Support Line
AUSTRALIA 1800 663 866
NEW ZEALAND 0800 666 783
EUROFLEX Australia Pty Ltd
8 Success Way
WANGARA WA 6065
AUSTRALIA
TEL: 08 9302 2526
Email: admin@euroex.com.au
Website: www.euroex.com.au
EUROFLEX New Zealand Ltd
PO BOX 305 650
Triton Plaza
North Shore 0757
NEW ZEALAND
TEL: 0800 666 783
Email: admin@euroex.com.au
Website: www.euroex.com.au
EUROFLEX SRL
Via dei Colli, 153
31058 Susegana (TV)
ITALY
Tel: +39 0438 661711
Email: euroex@euroex.tv
Website: www.euroex.tv
Loading...