Mitsubishi Electronics XL6500LU, XL6500U, XL6600LU, XL6600U User Manual
LAN Control Utility
User Manual (for XL6600U/XL6500U/XL6600LU/XL6500LU)
Contents
Preparation/SetUp .........................................................................2
Preparation before using the network function ...........................................2
Connection ..................................................................................................3
Installation ...................................................................................................3
Setting the IP address of the projector .......................................................5
When using a DHCP server ...........................................................................................6
When not using a DHCP server .....................................................................................7
Telnet setting ...............................................................................................8
Setting the password (Password Setup) .......................................................................9
Setting the display language of ProjectorView (language) ..........................................10
Setting the LAN control (LAN-Controlled Mode) .........................................................10
Setting the PJLink™ certifi cation (PJLink certifi cation Mode) .....................................11
Save and exit ...............................................................................................................11
ProjectorView ...............................................................................12
Using the ProjectorView ............................................................................12
How to start up ............................................................................................................12
VIRTUAL REMOTE controller .......................................................................................14
E-mail notifi cation function ..........................................................................................14
Initial setting .................................................................................................................15
Support for the PJLink™ function ...............................................16
EN-1
Preparation/SetUp
Preparation before using the network function
This projector is equipped with the network function to control and monitor the projector’s operations using a Web
browser and to send e-mail notifi cation.
Before using the network function, perform the following three preparation steps.
(1) Setup of the application software “Projector-Control Device Installer”
(2) Setting of the IP address of the projector
(3) Setting of password, display language, LAN control, and PJLink™ certifi cation using telnet.
*1
When setting IP addresses for multiple projectors collectively or when setting an IP address for a ceilingmounted projector after installation, check and take a note of combination of the projectors and the hardware
addresses (MAC addresses) in advance. To check the hardware addresses (MAC addresses), perform step 2
on the page 5.
[Major functions]
Setting of the projector’s IP address
Setting of password, display language, and LAN control
PJLink™ certifi cation setting (Telnet function)
Startup of the controlling / supervising tool (ProjectorView) using the Web browser
[System requirements]
Supported OS : Windows® 2000, Windows® XP
(Microsoft® .NET Framework 1.1*2 should be installed.)
CPU : Pentium II 233 MHz or higher
Memory : 128 MB or more
Free HDD space : 32 MB or more
Web browser : Internet Explorer Ver. 6.0
(Java Plug-in*3 should be installed and JavaScript should be enabled.)
*2
How to install Microsoft® .NET Framework Version 1.1
(1) Download .NET Framework Version 1.1 (file named “dotnetfx.exe”) from the download center on the
Microsoft® Web site (http://www.microsoft.com/downloads/).
(When the fi le is unavailable from the above-mentioned URL, search for .NET Framework using Windows
Update and access the download site found.)
(2) Execute the downloaded fi le named dotnetfx.exe.
*3
How to install Java Plug-in
(1) Download J2SE v1.4.2 JRE from the JAVA download center on the Sun Microsystems Web site (http://java.
sun.com/j2se/1.4.2/download.html).
(When the fi le is unavailable from the above-mentioned URL, search for “J2SE download” using a search
engine and access the download site found.)
(2) Execute the downloaded fi le.
(3) After the completion of the installation, select [Start] - [Control Panel] - [Java Plug-in] and disable the cache.
*1
• Microsoft or Windows are either registered trademarks or trademarks of Microsoft Corporation in the United
States and/or other countries.
• Pentium is trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and
other countries.
• The trademark of PJLink is trademark applied for registration or registered trademark in Japan, the United
States, and other countries and areas.
• Other brand or product names are trademarks or registered trademarks of their respective holders.
EN-2
Preparation/SetUp (continued)
Connection
Computer
LAN cable (option)
(100BASE-TX or 10BASE-T
should be supported.)
To LAN terminal
LAN cable (option)
(100BASE-TX or 10BASE-T should be supported.)
External HUB
• Use a straight-through category-5 cable for LAN connection.
• Don’t touch the metal parts of the LAN connector and LAN cable because static electricity may be discharged
from your body, causing damage to the projector.
Installation
Before starting installation, be sure to read “ReadMe.txt” contained in the CD-ROM.
1
2
3
Copy three fi les (DI_4.1.3.4.msi, Setup.Exe, and Setup.Ini) contained in the Tools folder of CD-ROM to the
hard disk of your personal computer.
Double-click the fi le named Setup.Exe.
When the following window appears, click Next.
EN-3
Preparation/SetUp (continued)
4
5
Select a folder to install the program, and click Next.
Click Next.
6
7
Installation starts.
• The progress of the installation process is
displayed as shown on the right.
When the installation process is completed, click
Close.
How to remove Projector-Control Device Installer
Select [Start] - [Control Panel] - [Add or Remove Programs] - [Projector-Control Device Installer] and click [Remove]
(in the case of Windows® XP).
EN-4
Preparation/SetUp (continued)
Setting the IP address of the projector
Before setting the IP address, check that the projector has been LAN-networked and turn on the main power of the
projector.
• When using multiple projectors, connect and configure them one by one. If you turn on the powers of the
projectors that are connected but not yet confi gured at the same time, they may not be recognized.
1
2
Start the Projector-Control Device Installer.
• Select [Start] - [All Programs] - [Projector] [Projector-Control Device Installer] (in the case of
®
Windows
Click the Search button.
• Projector is recognized.
(Note)
When projector isn’t recognized, check the following.
• The fi rewall function has been disabled. (When it
has been enabled, search may not be conducted.)
• The personal computer and the projector are on
the same network. (For preventing unauthorized
access.)
• More than one Projector-Control Device Installer
isn’t running.
XP).
3
4
Select a projector by clicking the line showing the
projector and click the Assign IP button.
The Assign IP Address screen appears.
Click here
(Don’t select this side. When you
execute IP assignment with this side
selected, it may become impossible to
control the projector.)
• For automatic IP address setting by the DHCP server, go to page 6. For IP address setting without using the
DHCP server, go to page 7.
EN-5
Preparation/SetUp (continued)
When using a DHCP server
5
6
7
Select [Obtain an IP address automatically] and click
Next.
Click Next.
• Check that the options are marked with check-
marks as shown on the right. Keep them unchanged for normal use.
Click Assign.
8
9
Click Finish.
Click the Search button.
• Check the IP address.
EN-6
Loading...