Page 1
Hand Dryer
Model
Instruction Manual
JT-SB116EH-W-CA
Single-phase 120VAC
0612874HD6901
For User
You should not attempt to install the unit yourself, as this may affect the safety and functionality of the unit.
Read this manual thoroughly before beginning using the unit to ensure it is used safely and correctly.
After reading the manual, store it in a location easily accessible for later reference.
Safety precautions
Do not allow water to get on unit.
This may cause electric shock.
Do not modify or disassemble.
This may cause fire, electric shock, or injury.
When changing the installation place, consult your dealer or instraller.
There is risk of injury.
Do not disassemble
Turn off the switch before cleaning the unit.
Not doing so may cause electric shock.
This appliance is not intended for use by young children or infirm persons unless they are adequately
supervised by a responsible person to ensure that they can use the appliance safely.
Young children should be supervised to ensure that they do not play with the appliance.
Important!
Follow instructions
Important!
Follow instructions
WARNING
Always use the unit with the drain tank and air filter attached.
Any water entering the unit may cause short circuits and electric shock.
Wear gloves when cleaning the unit.
Not doing so may cause injury.
If the unit stops working or begins acting strangely, turn off the power switch and ground-fault circuit
interrupter and contact your dealer for inspection and repairs.
Failure to do any of the above may cause electric shock or fire through short circuit.
Wait till the heater exterior cools down before starting maintenance.
Otherwise, it could cause burn.
Make sure to install the air filter on the heater and close the panel before starting to use.
Unless the filter is installed or panel is closed, dust entering the unit may cause fire.
Do not let children hang from the unit.
This may cause the unit to fall.
Care must be taken not to touch the heater exterior with hand or foot.
Heater exterior becomes extremely hot during operation. Touching it may cause burn on hand or foot.
Do not use for purposes other than drying hands.
Using the unit improperly can cause accidents.
Prohibited
Do not install the unit yourself.
This may affect the safety and functionality of the unit.
Do not use at locations where salt damage may occur or where corrosive, neutral or reductive gases are
present.
Failure to do any of the above may cause fire, electric shock or trouble.
Do not use in shower room or other locations with a great deal of humidity in the air or where
condensation may form on the unit.
This may cause electric shock or malfunction.
Prohibited
GB
The following may lead to death or serious personal injury if done incorrectly.
CAUTION
The following may lead to injury or damage to buildings or their contents if done incorrectly
Do not use in shower room
Do not allow the unit to get wet
Hot
Page 2
Main
2
3
1
Do not use in the following locations:
●
●
●
●
●
●
●
●
●
Locations where the temperature could be lower than 0˚C or higher than 40°C.
Locations where the humidity could be lower than 5% RH or higher than 95%RH.
Locations where the unit may come into direct contact with water.
Locations where the unit is under direct or strong sunlight. (May cause sensor to malfunction.)
Locations where there is a lot of condensation.
Do not use with chemicals (detergents, etc.) on your hands. (This may reduce the productive life of the unit.)
Do not use in locations where corrosive, neutral, or reductive gases are present.
(This may reduce the productive life of the unit and/or cause malfunctions.)
Locations where solt damage may occur.
Vehicles (incl. vessels, trains.)
Note
Features
Tamper-proof timer
To prevent tampering with the unit, the built-in timer shuts it down after 30 seconds of continuous use.
To continue use, remove hands and then re-insert.
"No-touch" hand drying, ensuring complete hygiene.
The jet-blow air dries wet hands quickly. You only pay for the electricity used to run it, so it’s economical.
A tamper-proof timer is built in to prevent overuse.
No need to throw out or replace paper towels, so maintenance is a cinch.
Anti-microbial finish.
As the jet-blow air is warmed with the heater, it will not feel cold even
when using in winter. (The unit accumulates heat because the heater
operates while the hand dryer is not used.)
Hot blow air dries hands quickly.
Although the heater is turned on when the heater switch is turned “ON”, the power is turned off automatically when the
room temperature becomes higher than 35˚C (temperatures at around the hand dryer).
When the heater switch is turned “ON”, the electricity is consumed because the heater operates while the hand dryer
is not used.
The heater is turned off automatically when using the hand dryer. (Motor and heater will not turn on simultaneously.)
Safety precautions (Continued)
2
Features of the heater
Hot jet-blow air …
Note
Page 3
3
Names and Uses of Parts
Power controll section
Power
switch
Heater
switch
Cover
Air
speed
knob
※Shades areas in the figure indicate
antimicrobial material.
Drain tank
Unit
Heater
Drain hose
Hand-drying area
Check lamp
Power lamp
Display
Emblem
Heater lamp
Black wall area
Sensor + Illumination lamp
Sensor
Air filter
-
+
O
FF
O
N
O
F
F
O
N
Power
Air speed
Heater
Page 4
4
How to use the unit
Introduction
Open the power controll section cover.
Turn on the power switch.
3.Close the power controll section cover.
Power controll section
Display
Power
switch
Heater
switch
Cover
Air
speed
knob
Power lamp
With the heater switch ON
Check lamp
Heater lamp
Power CheckHeater Power CheckHeater
Power lamp
With the heater switch OFF
Check lamp
Heater lamp
In case of trouble or error
Power CheckHeater
Power lamp
With the power switch OFF
Check lamp
Heater lamp
Power lamp
Check lamp
Heater lamp
Power CheckHeater
Check lamp
When a malfunction or error occurs, the check lamp on the right side of the display will
either light up or flash. Turn the power switch off, wait approximately 40 seconds until the
all the lamps in the display go off, and then turn the power back on. If the check lamp is
still on or flashing, turn off the power, shut off the ground-fault circuit interrupter, and
contact your dealer.
When not using the unit for long periods of time
(With the heater switch “OFF”)
* When the heater switch is turned “ON”, approx. 1,100 W of power is
consumed to accumulate heat by operating the heater.
Turn the power switch off.
The unit consumes approximately 2W of power even if unused when the power is on.
With both hands open, insert them
all the way in.
The unit will come on automatically.
Pull them out slowly,
letting the air blow the
water off.
Pull hands all the way
out.
Repeat until dry
Insert from each side. Bring upwards slowly. Pull out.
Information
As the hand dryer is open at both sides
of the main unit, your hands may also be
inserted from the sides. If your hands are
inserted from the sides and pulled
upwards a few times, you can dry your
hands without any risk of water drops
blowing upwards.
How to dry your hands
1.
2.
Note:
Power lamp and heater lamp turn on. (Display)
Emblem lamp turns on.
Illumination lamp turns on.
Adjust the Air speed knob to the best point.
When the power switch is turned on, make sure to remove
hands from the hand-drying area. Take sufficient care to
avoid this because it may deteriorate the sensitivity of sensor.
-
+
O
FF
O
N
O
FF
O
N
Power
Air speed
Heater
123
21
3
Maint
Drain tan
Display
Emblem
Power lamp
Heater lamp
Check lamp
Page 5
5
Maintenance
Wipe with a well-wrung wet rag
If the unit is very dirty, dip a rag in a neutral cleaning agent and wipe, then wipe
clean with a dry rag.
Remove dust from the sensor. (To prevent malfunction.)
Only use neutral cleaning agents.
Do not use thinner, benzene, or other acidic or
alkaline toilet cleaners, or plastic scrub brushes.
(These will damage the plastic and painted parts.)
Only the hand-drying area can be cleaned with
alcohol.
(Do not use alcohol at any places other than the hand-drying area.)
* Alcohol means the sterilizing ethanol (concentration 83%
or under).
* When cleaning the hand-drying area with alcohol, the
alcohol may drop along the drain hose and accumulate in the
drain tank. It could frost the drain window. Make sure to
drain alcohol accumulated in the drain tank after cleaning
with alcohol.
Chemical cloths should be used as indicated in their
instructions.
Disinfecting agents will damage the product.
When the power switch is turned on after cleaning,
make sure to remove hands or any foreign substance
from the hand-drying area. Otherwise, it may
deteriorate the sensitivity of sensor.
When the sensor sensitivity has deteriorated, turn the
power switch off once and back on again 40 seconds
later.
Maintenance and cleaning of the exterior
Before the unit starts looking too dirty
Warning
Always turn off the power when
cleaning the unit.
Do not splash water on the unit.
Wear gloves when cleaning.
Wait till the heater exterior cools down before
starting maintenance. (It may cause burn.)
Note
Caution
The antimicrobial material is effective when bacteria comes into contact with
the surfaces (Shaded area in the figure at left).
If those surfaces are dirty the
antimicrobial material
will not be
effective.
Drain tank
Unit
Heater
Drain hose
Black wall area
Sensor + Illumination lamp
Sensor
Hand drying area
Page 6
Name
Pow
Cov
6
Maintenance
(Continued)
Drain tank
Full water tank
Drain collection outlet
Drain tank
Lid
●
Do this only after checking that the drain tank is in place.
(Empty beforehand the water accumulated in the drain tank)
●
After repeating operations several times, make sure to empty the water
accumulated in the drain tank.
Pour 200p (around 1 cup) of water through the drain
hole. (To prevent it from getting clogged.)
The water blown off hands is called “drain water.”
Empty the drain tank at least once a week so that it does not reach the full line.
If the drain tank is not emptied it will start smelling.
●
Make sure the drain water does not spill out.
Pull the drain tank out horizontally.
1. Open the lid and empty the drain water.
●
Insert it securely all the way in the unit.
3. Replace the lid and then the entire drain tank to its
original location.
2. Wash out the interior of the drain tank.
Draining and cleaning the drain tank
Before it fills up (at least once a week)
Black wall area
●
Sensor’s sensitivity may be reduced if the black wall area is
fouled in white. Clean the area at least once a week
according to the Maintenance and cleaning of the exteriors.
Cleaning of the hand drying area (Cleaning of the black wall area)
About once every week
1
2
3
1
Page 7
7
Air filter
knob
Filter cover
●
Pull the knob.
1. Open the filter cover.
2. Remove the air filter
●
●
Pat it lightly by hand or use a vacuum cleaner.
If it is very dirty, wash it off with cold or lukewarm water.
1. Clean the filter.
●
If the air filter will not insert in the panel, try to invert it.
(Mounting direction is specified.)
1. Reinstall the air filter as it was.
●
Unless the panel is closed, dust may be inhaled in, resulting in fire.
2. Close the panel.
Cleaning the air filter
Around once a week
If you washed the air filter with water, dry it
thoroughly to remove all.
Do not expose the air filter to flame under any
circumstances whatsoever.
(Filter may be deformed.)
Note
Maintenance (Continued)
2
3
1
1
2
1
2
Page 8
Hand
Model
Instruc
JT-S
You sho
Read th
After re
Safety p
Do not
Importa
Follow
Importa
Follow
Pro
Pro
Do not use
Do not allow
1-3 Komaba-cho, Nakatsugawa City, Gifu Prefecture, Japan
If you think something has gone wrong?
Perform the following checks and fixes.
Problem Check Fix
Turn the ground-fault circuit interrupter on.
Turn the power switch on.
Place hands all the way in.
Turn OFF the power switch. After the power lamp at
the display has turned off, remove foreign substances
or fouling. Wait at least for 40 seconds and then turn
the power switch to ON again.
Turn the power switch off, check that all the lamps in
the display have gone off (around 40 seconds), and
then turn the power back on.
Turn the heater switch to ON .
Are you putting your hands in all the way?
Are any lamps in the display on?
Has a blackout occurred?
Is the sensor blocked by dirt or dust?
Hasn t the power switch been turned on while
hands are inserted in the hand-drying area?
No air blows even if hands are
inserted
Air does not stop blowing
Isn t the black wall area fouled in white in the
hand-drying area?
Isn t the heater switch turned OFF ?
No hot air comes out
Any problems with the power supply will cause
the lamp to go on or flash.
Check lamp is flashing
If the above fixes do not work, turn off the power and the ground-fault circuit interrupter and have your dealer
inspect and if necessary repair the unit. (Costs are as per agreement with dealer.)
This is due to oil and dust accumulated on the heater burning, and is not a malfunction.
Specifications
JT-SB116EH-W-CA
●
The drain tank capacity is 0.8R.
Model
Voltage Frequency
Power input
(W)
110060Hz
Current
(A)
Weight
(kg)
9.2
120V
14
Dimensions (WDH)
300222835 (mm)
During initialization, smoke and odors
emanate from the hot air outlet vent.
Loading...