Mitsubishi Electric t-NEXT DF DX 011 P1 S, t-NEXT DF DX 016 P1 S, t-NEXT DF DX 014 P1 S, t-NEXT DF DX 020 P1 S, t-NEXT DF DX 022 P1 S User Manual

The picture of the unit is indicative and may vary depending on the model

• PERIMETER INSTALLATION

• FULLY HERMETIC ON/OFF COMPRESSORS

• DUAL FLUID SYSTEM WITH ADDITIONAL COIL

• SINGLE OR DOUBLE REFRIGERANT CIRCUIT

• AIR DELIVERY FROM THE BOTTOM (UNDER) OR FROM THE TOP (OVER)

• PLUG FANS WITH EC ELECTRIC MOTOR

• ELECTRONIC EXPANSION VALVE

• AIR SUCTION TEMPERATURE UP TO 40°C

t-NEXT DF DX

10 – 149 kW

Air conditioners for IT Cooling with Dual Fluid system. To be matched with remote air-cooled condenser.

Data Book: T_tNEXTDFDX_0719_EN

CLOSE CONTROL AIR CONDITIONERS

rcitcooling.com

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

2

MEHITS S.p.A.

DATA BOOK

INDEX

MEHITS CERTIFICATIONS ........................................................................................................................................................................................................... 4

GENERAL CHARACTERISTICS ................................................................................................................................................................................................... 5

INSTALLATION .............................................................................................................................................................................................................................. 6

PRODUCT FEATURES AND BENEFITS ...................................................................................................................................................................................... 6

F-GAS DIRECTIVE ........................................................................................................................................................................................................................ 6

MODEL IDENTIFICATION ............................................................................................................................................................................................................. 7

TRANSPORT AND STORAGE TEMPERATURE .......................................................................................................................................................................... 7

WORKING LIMITS ......................................................................................................................................................................................................................... 8

MAIN COMPONENTS .................................................................................................................................................................................................................... 9

REMOTE AIR-COOLED CONDENSERS .................................................................................................................................................................................... 11

OPTIONAL ACCESSORIES ........................................................................................................................................................................................................ 11

TECHNICAL DATA ...................................................................................................................................................................................................................... 14

DUAL FLUID SYSTEM ................................................................................................................................................................................................................. 18

2-WAY BALL VALVE FOR CHILLED WATER FLOW CONTROL .............................................................................................................................................. 19

WATER QUALITY OF THE HYDRAULIC CIRCUITS .................................................................................................................................................................. 20

ANTIFREEZE MIXTURES ........................................................................................................................................................................................................... 20

REFRIGERANT CHARGE ........................................................................................................................................................................................................... 21

PRESSURE RELIEF VALVE ....................................................................................................................................................................................................... 22

REFRIGERANT CIRCUIT ............................................................................................................................................................................................................ 23

RECOMMENDED REFRIGERANT LINES .................................................................................................................................................................................. 25

INSTALLATION DIAGRAM .......................................................................................................................................................................................................... 26

ACOUSTIC DATA ........................................................................................................................................................................................................................ 27

ELECTRICAL DATA ..................................................................................................................................................................................................................... 28

MICROPROCESSOR CONTROL SYSTEM ................................................................................................................................................................................ 29

DEMAND LIMIT ............................................................................................................................................................................................................................ 31

TEMPERATURE PROBE ON AIR RETURN / DELIVERY .......................................................................................................................................................... 31

CLOGGED FILTERS SENSOR ................................................................................................................................................................................................... 31

FLOOD SENSOR ......................................................................................................................................................................................................................... 31

POSSIBLE AIR INTAKE FOR OVER VERSIONS ....................................................................................................................................................................... 32

REMOTE AIR-COOLED CONDENSER ....................................................................................................................................................................................... 33

OPTIONAL ACCESSORIES: P121 – FRONT AIR INTAKE+BOTTOM PANEL .......................................................................................................................... 35

OPTIONAL ACCESSORIES: 601 – SOLENOID VALVE ON LIQUID LINE ................................................................................................................................ 35

OPTIONAL ACCESSORIES: A548 - CONSTANT PREVALENCE ............................................................................................................................................. 35

OPTIONAL ACCESSORIES: P091 - BACK-UP MODULE CONTROLLER ................................................................................................................................ 35

OPTIONAL ACCESSORIES: P171 – KIT FOR AIR -45°C MCH AXIAL AC ............................................................................................................................... 36

OPTIONAL ACCESSORIES: P172 – KIT FOR AIR -45°C AXIAL AC ........................................................................................................................................ 36

OPTIONAL ACCESSORIES: A492 – WATER LEACKAGE DETECTOR + ADDITIONAL DETECTOR..................................................................................... 37

OPTIONAL ACCESSORIES: A511 - SMOKE DETECTORS ...................................................................................................................................................... 37

OPTIONAL ACCESSORIES: A512 – FIRE DETECTORS .......................................................................................................................................................... 37

ACCESSORI: P181 – ANALIZZATORE DI RETE ....................................................................................................................................................................... 38

ACCESSORI: P182 – ANALIZZATORE DI RETE+OPTIONAL ................................................................................................................................................... 38

ACCESSORI: P183 – KIT ANALIZZATORE DI RETE ................................................................................................................................................................. 38

ACCESSORI: P184 – KIT ANALIZZATORE DI RETE+ OPTIONAL ........................................................................................................................................... 38

OPTIONAL ACCESSORIES: P021 – 2-WAY BALL BY-PASS VALVE ....................................................................................................................................... 39

OPTIONAL ACCESSORIES: A431 – ELECTRIC HEATERS ...................................................................................................................................................... 41

OPTIONAL ACCESSORIES: A432 – EXTRA POWER ELECTRIC HEATERS .......................................................................................................................... 41

OPTIONAL ACCESSORIES: 4301 – STEAM HUMIDIFIER 3KG/H ............................................................................................................................................ 43

OPTIONAL ACCESSORIES: 4303 – STEAM HUMIDIFIER 8KG/H ............................................................................................................................................ 43

OPTIONAL ACCESSORIES: 4305 – STEAM HUMIDIFIER 15KG/H .......................................................................................................................................... 43

OPTIONAL ACCESSORIES : P051 – DEHUMIDIFICATION FUNCTION .................................................................................................................................. 46

OPTIONAL ACCESSORIES: P161 - T/RH AIR INTAKE SENSOR ............................................................................................................................................. 46

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

3

MEHITS S.p.A.

DATA BOOK

OPTIONAL ACCESSORIES: P071 - REMOTE T/RH PROBE .................................................................................................................................................... 46

OPTIONAL ACCESSORIES: 4666 – EXTERNAL AIR PROBE .................................................................................................................................................. 46

OPTIONAL ACCESSORIES: P111 – DUAL POWER SUPPLY .................................................................................................................................................. 47

OPTIONAL ACCESSORIES: P112 – DUAL POWER SUPPLY + OPTIONAL ............................................................................................................................ 47

OPTIONAL ACCESSORIES: P113 – KIT DUAL POWER SUPPLY ........................................................................................................................................... 47

OPTIONAL ACCESSORIES: P114 – KIT DUAL POWER SUPPLY + OPTIONAL ..................................................................................................................... 47

OPTIONAL ACCESSORIES: A381 - DRAIN PUMP .................................................................................................................................................................... 48

OPTIONAL ACCESSORIES: P084 – AIR FILTER EPM

10

50% .................................................................................................................................................. 49

OPTIONAL ACCESSORIES: A531 – ON-OFF DAMPER ........................................................................................................................................................... 50

OPTIONAL ACCESSORIES: P011 - EMPTY PLENUM .............................................................................................................................................................. 52

OPTIONAL ACCESSORIES: P012 - EMPTY PLENUM CL.A1 ................................................................................................................................................... 52

OPTIONAL ACCESSORIES: P031 - EMPTY INTAKE PLENUM ................................................................................................................................................ 52

OPTIONAL ACCESSORIES: P032 - EMPTY INTAKE PLENUM CL.A1 ..................................................................................................................................... 52

OPTIONAL ACCESSORIES: P013 - PLENUM + 3 GRILLES ..................................................................................................................................................... 52

OPTIONAL ACCESSORIES: P014 - PLENUM + 3 GRILLES CL.A1 .......................................................................................................................................... 52

OPTIONAL ACCESSORIES: P015 - SILENCED PLENUM ........................................................................................................................................................ 52

OPTIONAL ACCESSORIES: P016 - SILENCED PLENUM + 1 GRILLE .................................................................................................................................... 52

OPTIONAL ACCESSORIES: P017 - PLENUM + FILTER EPM2.5 50% ..................................................................................................................................... 52

OPTIONAL ACCESSORIES: P018 - PLENUM + FILTER EPM1 50% ........................................................................................................................................ 52

OPTIONAL ACCESSORIES: P019 - PLENUM + FILTER EPM1 85% ........................................................................................................................................ 52

OPTIONAL ACCESSORIES: P034 – INTAKE FREE-COOLING PLENUM ................................................................................................................................ 59

OPTIONAL ACCESSORIES: P041 – SUPPORT FRAME H 255-350MM ................................................................................................................................... 63

OPTIONAL ACCESSORIES: P042 – SUPPORT FRAME H 355-450MM ................................................................................................................................... 63

OPTIONAL ACCESSORIES: P043 – SUPPORT FRAME H 400-510MM ................................................................................................................................... 63

OPTIONAL ACCESSORIES: 1511 – SOFT STARTER ............................................................................................................................................................... 64

OPTIONAL ACCESSORIES: A272 – CL.0 OR A1 (EN13501-1) INSULATION .......................................................................................................................... 65

MACHINE DRAWINGS ................................................................................................................................................................................................................ 66

HOLE IN THE RAISED FLOOR FOR DOWNFLOW VERSION .................................................................................................................................................. 83

EXAMPLE FOR MACHINES NOISE EMISSION CALCULATION............................................................................................................................................... 84

VALVE PRESSURE DROP CALCULATION AS FUNCTION OF WATER FLOW RATE ............................................................................................................ 86

AIR FILTERS REPLACEMENT .................................................................................................................................................................................................... 87

SHIPMENT: PACKING DIMENSIONS ......................................................................................................................................................................................... 88

SHIPMENT: SHIPPING WEIGHT ................................................................................................................................................................................................ 88

SHIPMENT: OPTIONALS PACKING DIMENSIONS AND SHIPPING WEIGHT ......................................................................................................................... 89

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

4

MEHITS S.p.A.

DATA BOOK

MEHITS CERTIFICATIONS

SYSTEM CERTIFICATIONS

ISO 9001 CERTIFICATION – MEHITS S.p.A.

Quality Management System

ISO 14001 CERTIFICATION – MEHITS S.p.A.

Environmental Management System

BS OHSAS 18001 CERTIFICATION – MEHITS S.p.A.

Occupational Health and Safety Management System

PRODUCT CERTIFICATIONS BY COUNTRY

CE MARKING MEHITS units are in compliance with the European Directives in force.

CCC – CQC CERTIFICATION

(People’s Republic of China)

EAC CERTIFICATION

(Russian Federation, Belarus, Kazakhstan)

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

5

MEHITS S.p.A.

DATA BOOK

GENERAL CHARACTERISTICS

Air Conditioners for IT Cooling with Dual Fluid system.

• Direct expansion, air cooled.

For matching with remote air-cooled condenser;

• Two independent cooling systems:

Direct expansion coil; Chilled water coil;

• Plug fans with EC electric motors;

• Rotary or scroll on/off compressors;

• Single or double refrigerant circuit.

This series is offered in 20 models available in the following versions:

• The upflow version (Over) is characterized by air intake from the front through honeycomb grille

and air delivery from the top of the unit.

• The downflow version (Under) is characterized by air intake from the top and air delivery from

the bottom of the unit.

Cooling capacity: 10 ÷ 149 kW

The machines are made for indoor installation.

The constructive solutions and the internal lay-out allow high application flexibility and the frontal access to the main components for the inspection and routine maintenance.

The installation requires refrigerant charge, electrical and hydraulic connections.

Final assembly on all machines before shipment including running test, reading and monitoring of operating parameters, alarms simulation and visual check.

UNDER

Downflow air delivery

OVER

Upflow air delivery

UNDER

Downflow air delivery

OVER

Upflow air delivery

Air conditioner

Remote

condenser

Liquid chiller

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

6

MEHITS S.p.A.

DATA BOOK

INSTALLATION

The series is particularly suitable for installation in Data Centre of medium / small size with constant load.

DOWNFLOW VERSION (Under)

Typical installation is on the perimeter. The units are placed along the perimeter of the Data Center. Air suction from the top of the unit and air delivery in the underfloor void. The air distribution is achieved by special tiles placed in front of the racks row, forming cold aisle for air diffusion. On the rear of the racks is expelled the hot then aspirated by the unit. For an optimal installation is advisable to provide the cold aisle containment.

Some solutions provide a service corridor around the server rooms where to place the units. In this case, it is necessary to provide the air intake plenum for each unit. With this solution, all the space in the Data Center is available for the installation of racks.

UPFLOW VERSION (Over)

The type of installation is practically similar to the previous. The only difference is that for the air distribution

in the Data Center is not used the raised floor but ducts in the ceiling.

The series is also suitable for installation in UPS, Batteries, Distribution rooms and in all service areas of the Data Center that need a service of conditioning.

OPTIONAL An extensive list of accessories allows the unit to adapt effectively to the real needs of the system, reducing the time and cost of installation.

PRODUCT FEATURES AND BENEFITS

• Dual Fluid System: Two independent cooling systems: Chilled water coil; Direct expansion coil

• Electronic expansion valve;

• New plug fans with EC electric motors and impeller in composite material, which guarantees a

reduction of power consumption;

• New fans electric motor that do not require maintenance;

• Improvement of the control software with advanced control logic;

• Single or double refrigerant circuit;

• Air suction temperature up to 40°C

F-GAS DIRECTIVE

The units highlighted in this publication contain <HFC R410A [GWP

100

2088]> fluorinated

greenhouse gases.

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

7

MEHITS S.p.A.

DATA BOOK

MODEL IDENTIFICATION

Air conditioners for IT Cooling model: t-NEXT DF DX O 041 P1 S E4

t-NEXT Series

DF DX Unit type

DF – with dual fluid system Two independent cooling systems: Direct expansion coil, chilled water coil, DX – direct expansion, air cooled

O Air delivery

O = over – upflow air delivery U = under – downflow air delivery

041 Model / Cooling capacity (kW) at nominal conditions

P1 Compressor type and number P = scroll compressor for R410A

1 = number of compressors

S Refrigerant circuit

S = single D = double

E4 Size

TRANSPORT AND STORAGE TEMPERATURE

During transport and if the machine is not installed at the reception, do not remove the packaging and place the machine in an enclosed, dry and protected from sunlight site at temperatures ranging between -30°C and 50°C in absence of superficial condensation.

THE RANGE

UNDER

OVER

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

8

MEHITS S.p.A.

DATA BOOK

WORKING LIMITS

ROOM AIR CONDITIONS Room air temperature: 14°C minimum temperature with wet bulb. 24°C maximum temperature with wet bulb. 18°C minimum temperature with dry bulb 40°C maximum temperature with dry bulb.

AREA “A”. Machine operating envelope.

Room air humidity: 20%RH minimum relative humidity. 60%RH maximum relative humidity.

AMBIENT AIR TEMPERATURE 45°C Maximum ambient air temperature

-20°C Minimum ambient air temperature

With “Kit for air -45°C” for low ambient temperature operation (optional)

-45°C minimum ambient air temperature with remote condensers with AC fans

CHILLED WATER TEMPERATURE (Dual Fluid circuit) 6-25°C temperature range of the water entering the coil

ΔT 3°C Minimum temperature difference between water inlet and outlet ΔT 10°C Maximum temperature difference between water inlet and outlet

All the values are indicative. The working temperatures are influenced by a series of variables as:

• Working conditions;

• Thermal load;

• Set of the microprocessor control.

HYDRAULIC CIRCUIT (Dual Fluid circuit) ΔP 5-150kPa Pressure drop range of the hydraulic circuit. 10 Bar Maximum working pressure of the hydraulic circuit

POWER SUPPLY ± 10% Maximum tolerance of the supply voltage (V) ± 2% Maximum unbalancing of the phases.

A

Relative humidity

- %

Relative humidity - %

Dry bulb temperature - °C

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

9

MEHITS S.p.A.

DATA BOOK

MAIN COMPONENTS

FRAMEWORK

• Base in aluminium extrusion, painted with epoxy powders. Colour RAL 9005;

• Frame in aluminium profile, painted with epoxy powders. The inner frame is provided with

seals for the panels. Colour RAL 9005;

• Panels in galvanized steel sheet with protective surfaces treatment in compliance with UNI

ISO 9227/ASTMB117 and ISO 7253, and painted with epoxy powders. Colour RAL 7016 hammered;

• Panels insulated with polyurethane foam and seals to ensure air tight.

• Hinged front panels with quick release removal system.

• Total front access for routine maintenance.

• Removable lateral and back side panels.

• Air flow OVER version:

- Air intake from the front through honeycomb type grille and air delivery from the top.

• Air flow UNDER version:

- Air intake from the top and air delivery from the bottom.

• Compartment for electrical panel on unit front for direct access to control and regulation

devices;

FILTER SECTION

• Washable air filters with COARSE 60% efficiency (according to ISO EN 16890), with cells in

synthetic fibre and metallic frame.

• Air filters access:

OVER version

- Frontal access for all machines

UNDER version

- For machines size E1 – E2 – E3 frontal access

- For machine size E4 – E5 – E6 – E7 – E8 – E9 access from upper side

• Clogged filters sensor with differential pressure switch on air side.

ON / OFF COMPRESSORS SECTION

Units size E1 and E2:

• Rotary vane compressors for R410A refrigerant

• 2-pole 3-phase electric motor with direct on line starting.

• Crankcase heater.

• Rubber supports.

Units size E3, E4, E5, E6, E7, E8 and E9

• Scroll rotary compressors with spiral profile optimized for R410A refrigerant.

• 2-pole 3-phase electric motor with direct on line starting.

• Crankcase heater.

• Rubber supports.

FANS SECTION

The fan section is contained within the machine and includes:

• Centrifugal fans with backward curved blades with wing profile, single suction and without

scroll housings (Plug-fans), directly coupled to external rotor electric motor.

• Impeller in composite material exempt from rust formation.

• Brushless type synchronous EC motor with integrated electronic commutated system and

continuous variation of the rotation speed. The motor rotation control is obtained with the EC system (Electronic Commutation) that manage the motor according to the signal coming from the microprocessor control.

• Fans control through ModBus. In case of failure, the control stops the interested fan indicating

the type of fault. The machine with more than one fan is not stopped.

• Adjustable External Static Pressure (ESP).

• Fan guard with rubber support (UNDER version)

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

10

MEHITS S.p.A.

DATA BOOK

COOLING SECTION – DIRECT EXPANSION COIL

• Heat exchanger coil with internally corrugated copper tubes and high efficiency aluminium

fins, specifically developed to provide high heat transfer and lower pressure drops.

• Frame in galvanized steel or peraluman.

• Condensate tray in peraluman with PVC flexible discharge pipe.

• Temperature sensor on air intake with control and regulation functions.

• Temperature sensor on air delivery with function of temperature display.

• Under floor water alarm through sensor to be placed on the floor.

COOLING SECTION – CHILLED WATER COIL

• Chilled water 4 rows cooling coil with copper tubes, aluminium fins and galvanized steel

frame.

• 2-way motorized valve with 0÷10 VDC control actuator and emergency manual control.

• Temperature probe on water inlet.

• Hydraulic pipes in copper with anticondensate insulation

REFRIGERANT CIRCUIT

The air conditioner is supplied with a minimum R410A refrigerant charge. Components for each refrigerant circuit:

• Electronic expansion valve. The valve allows high performance and system efficiency thanks

to a timely and accurate response to changes in temperature and pressure.

• Sight glass.

• Filter dryer on liquid line.

• Pressure transducers with indication, control and protection functions, on low and high

refrigerant pressure.

• High pressure safety switch with manual reset.

• Liquid receiver.

• Pressure relief valve on liquid receiver for models 041 P1, 045 P1, 075 P2, 082 P2,

092 P2, 102 P2, 117 P4, 146 P4.

• Refrigerant circuit with copper tubing with anticondensate insulation of the suction line.

• Lubricant oil charge.

• Valves on gas delivery and liquid return for coupling to remote air-cooled condenser.

• 0÷10V proportional signal to manage the condensing control system of the remote air-cooled

condenser.

• Condensing control by continuous variation of remote condenser fan rotation speed for

operations with ambient temperature down to -20°C.

ELECTRICAL PANEL

In accordance with EN60204-1 norms, suitable for indoor installation, complete with:

• Main switch with door lock safety on frontal panel.

• Magnetothermic switches for each compressor.

• Magnetothermic switches for supply fans.

• Contactors for each load. The supply fans equipped with EC electric motor don’t require

contactors.

• Transformer for auxiliary circuit and microprocessor supply.

• Numbered wirings.

• Terminals:

OUTLETS

- Voltage free deviating contact for General Alarm 1-2

- Voltage free contact for supply fans status.

- Voltage free contact for smoke / fire sensor (the sensors are accessory)

INLETS

- External enabling.

• Power supply 400/3+N/50.

CONTROL SYSTEM

Microprocessor control system with graphic display for control and monitor of operating and alarms status. The system includes:

• Built-in clock for alarms date and time displaying and storing;

• Built-in memory for the storing of the intervened events (up to 200 events recorded);

• Predisposition for additional connectivity board housing (MODBUS, LON,

BACNET MS/TP RS485, BACNET OVER IP). The electronic cards are optional accessories.

• Main components hour-meter;

• Non-volatile “Flash” memory for data storage in case of power supply faulty;

• Menu with protection password;

• Demand Limit function;

• LAN connection (max 10 units).

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

11

MEHITS S.p.A.

DATA BOOK

REMOTE AIR-COOLED CONDENSERS

The descriptions of these series can be found in Chapter REMOTE AIR-COOLED CONDENSERS.

............................................ Remote air-cooled condenser: Remote air-cooled condenser in

PERALUMAN aluminium alloy with microchannel condensing coil: P821 - with AC axial fans and standard acoustic version

series GR-Z A B 50;

P831 - with AC axial fans and low noise acoustic version

series GR-Z A L 50;

P841 - with EC axial fans and standard acoustic version

series GR-Z E B 50;

P851 - with EC axial fans and low noise acoustic version

series GR-Z E L 50.

Remote air-cooled condenser with condensing coil with copper tubes and aluminium fins:

- with AC axial fans series T-MATE DX-A;

- with EC axial fans series T-MATE DX-E;

- with EC plug-fans series T-MATE DX-PF-E.

OPTIONAL ACCESSORIES

The descriptions of these additional components can be found in Chapter OPTIONAL ACCESSORIES.

P121 .................................... Front air intake + bottom panel. Unit base noise insulation with special

bottom panel for OVER version. Restriction: Non-compatible with “P122 Bottom air intake + blind panels” for OVER version.

P122 .................................... Bottom air intake+blind panels. Blind frontal panel for OVER version. The

accessory allows the intake air from the bottom of the machine. Restriction:

Not compatible with “P121 Front air intake + bottom panel” for OVER

version.

601 ...................................... Solenoid valve on liquid line.

A548 .................................... Constant prevalence. Automatic system for the air pressure control in the

aisle. The system controls the supply fans rotation speed to keep constant the air pressure via a differential pressure transmitter connected to the microprocessor control.

P091 .................................... Back-up module controller. The system guarantees the microprocessor

power supply for a few minutes, in case of supply voltage failure. (size E1 excluded).

P171 .................................... Kit for air -45°C MCH axial AC (condenser series GR). Kit for operations

with low ambient air temperature down to -45°C. For machine start up and operation with very low ambient air temperatures (between -20°C and 45°C).

P172 (1) .............................. Kit for air -45°C axial AC (condenser series T-MATE). Kit for operations

with low ambient air temperature down to -45°C. For machine start up and operation with very low ambient air temperatures (between -20°C and 45°C).

P191 .................................... Power supply for condenser. Electrical power supply for remote

condenser from the indoor machine electrical board. The optional includes magneto-thermic switches for condenser fans and the control/alarm signals.

383 ...................................... Numbered wirings + UK requests;

4181 / 4182 / 4184 / 4185 ... Serial cards: 4181 – Serial card MODBUS; 4182 – Serial card LON; 4184 – Serial card BACNET MS/TP RS485; 4185 – Serial card BACNET OVER IP.

A492 .................................... Water leakage detector + additional sensor. Supplied in mounting kit.

A511 .................................... Smoke detector. Supplied in mounting kit.

A521 .................................... Fire detector. Supplied in mounting kit.

P141 .................................... Analogue set-point compensation. - Analogue set point compensation

according to an external analogue signal at Customer care.

The microprocessor control, through the additional module “expansion card”, can manage a compensation signal of the return air setpoint by

analogue input (0...1V; 0...5V; 0,5...4,5V; 4...20mA; 0...20mA). The compensation curve allows to assign a temperature setpoint offset respectively to the minimum and maximum signal managed by the input.

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

12

MEHITS S.p.A.

DATA BOOK

P181 .................................... Network analyser (standard machine) Multifunction utility for calculating and

displaying the machine electrical measurements.

P182 .................................... Network analyser+optional (full optional machine) Multifunction utility for

calculating and displaying the machine electrical measurements.

P183 .................................... Kit network analyser (standard machine) Multifunction utility for calculating

and displaying the machine electrical measurements. Supplied in mounting kit.

P184 .................................... Kit network analyser+optional (full optional machine) Multifunction utility

for calculating and displaying the machine electrical measurements. Supplied in mounting kit.

A812 (2) .............................. Free-cooling direct control.

P021 .................................... 2 way 0-10V modulating water valve.2-way motorized valve with 0÷10

VDC control actuator and emergency manual control for the third way (bypass) of the chilled water hydraulic circuit. The valve is in combination with the main water flow control valve

A431 .................................... Electric heater. Heating with electric heaters.

A432 .................................... Extra power electric heater. Size E1, E2 excluded.

4301 / 4303 / 4305 (3) ......... Humidification: Modulating steam humidifier with immersed electrodes

with electronic control.

4301 - Steam humidifier 3kg/h 4303 - Steam humidifier 8kg/h

4305 - Steam humidifier 15kg/h

P051 (4) .............................. Dehumidification function.

P161 .................................... T/rH air intake sensor. Combined Temperature / Humidity sensor on air

intake. The optional replace the standard temperature sensor on machine

air intake.

4666 .................................... External air probe. External air temperature probe.

P071 .................................... Remote T/rH probe. Combined Temperature / Humidity sensor for remote

installation. The optional is added to the standard temperature sensor on

machine air intake.

P111 / P112 / P113 / P114 . Dual power supply. Dual power supply with automatic change-over.

P111 - Dual power supply.

P112 - Dual power supply + optional.

P113 - Dual power supply kit. Supplied in mounting kit

P114 - Dual power supply kit + optional. Supplied in mounting kit

A381 .................................... Drain pump. Supplied in mounting kit. The system includes pump with

activation float and 10 linear meters long discharge pipe.

P084 .................................... Air filter ePM10 50%. Washable high efficiency air filter (according to ISO

EN 16890). Not compatible with “P017 / P018 / P019 Plenum + filter ePM

2.5

50%, ePM1 50%, ePM1 85% (according to ISO EN 16890)”.

A531 (5) .............................. On-off damper. Non-return air damper with frame driven by electric

servomotor installed on the machine air delivery.

P011 .................................... Empty plenum.

P012 .................................... Empty plenum CL.A1. Plenum with fire reaction in class “0” or “A1”.

P013 .................................... Plenum + 3 grilles on three sides with double adjustable row.

P014 .................................... Plenum + 3 grilles CL.A1. Plenum with grilles on three sides with double

adjustable row, with fire reaction in class “0” or “A1”.

P015 .................................... Silenced plenum. Not compatible with “P084 Air filter ePM10 50%.”.

P016 .................................... Silenced plenum + 1 grille. Grille with double adjustable row on front side

and sound absorbers.

P017 .................................... Plenum + filter ePM

2,5

50%. Plenum with high efficiency air filter (according

to ISO EN 16890). Not compatible with “P084 Air filter ePM10 50%.”.

P018 .................................... Plenum + filter ePM1 50%. Plenum with high efficiency air filter (according

to ISO EN 16890). Not compatible with “P084 Air filter ePM10 50%.”.

P019 .................................... Plenum + filter ePM1 85%. Plenum with high efficiency air filter (according

to ISO EN 16890). Not compatible with “P084 Air filter ePM10 50%.”.

P031 (6) .............................. Empty intake plenum.

P032 (6) .............................. Empty intake plenum CL.A1. Plenum with fire reaction in class “0” or “A1”.

(size E0 excluded).

P034 (7) .............................. Intake free-cooling plenum.

P041 / P042 / P043 ............. Support frame with height adjusting rubber holders. Supplied in mounting

kit. It is not possible to match the support frame with plenum installed under

the machine.

P041 – Support frame h 255-350mm

P042 – Support frame h 355-450mm

P043 – Support frame h 400-510mm

3601 .................................... Compressor operating signal contact. Voltage free contact for

compressor status signalling.

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

13

MEHITS S.p.A.

DATA BOOK

2411 .................................... Phase sequence relay. Phases sequence control relay for the machine.

The system checks that the phase sequence of the power supply is correct

to prevent the opposite rotation of the three phase electric motors of the

machine as compressors. The optional is installed in the electrical box

downstream the main switch with door lock safety and in case of wrong

phase sequence prevents starting the machine;

1511 .................................... Soft starter. Compressor motors soft-starter system (size E1, E2

excluded).

3301 .................................... Compressor rephasing. Compressors capacitor for power factor - cosφ

0,9 (sizes E1, E2 excluded).

A181 .................................... Compressor soundproof jacket. Compressor soundproof jacket for a

sound level reduction of 2 dB(A).

A272 .................................... CL. 0 or A1 (EN 13501-1) insulation: Panelling with fire reaction in class

“0” or “A1;

P151 .................................... Lowered display for Under – for UNDER units equipped with plenum

under the unit.

9973 .................................... Wooden cage packing. The machines are delivered on wooden pallet,

covered with shrink wrap and packaged in wooden cage.

7387012600 ........................ Remote terminal. Graphic display for remote installation, the optional is

added to the standard graphic display placed on machine frontal panel.

WARNING The Manufacturers reserves the right to accept the matching of the optional installed on the machine.

MANDATORY COMBINATIONS OF ACCESSORIES

1. When optional accessory “P172 Kit for air -45°C axial AC” is present, it requires mandatory

accessory “P191 Power supply for condenser”.

2. When optional accessory “A812 Free cooling direct control” is present, it requires mandatory

accessories “P161 T/rH air intake sensor“ and “4666 External air probe”.

3. When optional accessories “4301 / 4303 / 4305 Steam humidifier” are present, they require

mandatory accessory “P161 T/rH air intake sensor“.

4. When optional accessory “P051 Dehumidification function” is present, it requires mandatory

accessory “P161 T/rH air intake sensor“.

5. When optional accessory “A531 On-off damper” is present, it requires mandatory accessory

“9973 Wooden cage packing”.

6. When optional accessories “P031 Empty intake plenum, for OVER version” and “P032 Empty

intake plenum CL.A1, for OVER version” are present, they require mandatory accessory “P122 Bottom air intake+blind panels, for OVER version only”

7. When optional accessory “P034 Intake free-cooling plenum” is present, it requires mandatory

accessories “P161 T/rH air intake sensor“, “4666 External air probe”, “A812 Free-cooling direct control” and “P122 Bottom air intake+blind panels, for OVER version only”

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

14

MEHITS S.p.A.

DATA BOOK

TECHNICAL DATA

VERSION (1)

U / O

MODEL 011 P1 S

014 P1 S

016 P1 S

020 P1 S

022 P1 S

SIZE E1

E2

E3

COOLING CAPACITY (2)

Total

kW

10,3

13,8

16

20,3

22,1

Sensible

kW

10,2

13,8

14,8

20,3

22,1

SHR (3) 0,99 1 0,92 1 1

Total power input (Comp. + Fans)

kW

2,64

3,27

3,74

4,54

5,5

"EC" SUPPLY FANS

n. 1 1 1 1

1

Air flow

m³/h

2800

4000

4200

5700

6100

Nominal external static pressure

Pa

20

Maximum external static pressure

Pa

29

329

276

803

729

Fans power input (4)

kW

0,35

0,5

0,57

0,85

1,04

ON/OFF COMPRESSORS

rotary vane

scroll

Compressors number

n. 1 1 1 1

1

Capacity steps

n. 1 1 1 1

1

Compressors power input

kW

2,29

2,77

3,16

3,69

4,46

AIR FILTERS

n. 1 1 1 2

2

Filter area

m2

0,61

0,78

1,24

Efficiency (ISO EN 16890)

COARSE

60%

REFRIGERANT CIRCUITS

n. 1 1 1 1

1

POWER SUPPLY

V/Ph/Hz

400/3+N/50

ENERGY EFFICIENCY INDEX (2) (5)

EER Energy Efficiency Ratio

kW/kW

3,90

4,22

4,28

4,47

4,02

DIMENSIONS

Length

mm

650

785

1085

Width

mm

675

775

Height

mm

1925

NET WEIGHT OVER

kg

248

283

288

333

338

NET WEIGHT UNDER

kg

258

293

298

353

358

REFRIGERANT CONNECTIONS

Gas delivery

ODS Ø

12

16

Liquid return

ODS Ø

12

16

HYDRAULIC CONNECTIONS

CONDENSATE DISCHARGE

Rubber pipe – internal diameter

Ø mm

19

THE COOLING CAPACITY DOES NOT CONSIDER THE SUPPLY FAN MOTOR THERMAL LOAD

1. U = Under, downflow / O = Over, upflow

2. Gross value. Characteristics referred to entering air at 26°C-40%RH; condensing temperature 45°C. ESP=20Pa.

3. SHR = Sensible cooling capacity / Total cooling capacity.

4. Corresponding to the nominal external static pressure

5. The Energy Efficiency Index does not consider the remote air-cooled condenser.

The units highlighted in this publication contain <HFC R410A [GWP

100

2088]> fluorinated greenhouse gas

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

15

MEHITS S.p.A.

DATA BOOK

TECHNICAL DATA

VERSION (1)

U / O

MODEL 026 P1 S

032 P1 S

037 P1 S

041 P1 S

045 P1 S

SIZE E3

E4

COOLING CAPACITY (2)

Total

kW

26,2

32,5

37,6

41,4

45,4

Sensible

kW

25,3

32,5

37,6

41,2

43,4

SHR (3) 0,97 1 1 1 0,96

Total power input (Comp. + Fans)

kW

6,74

7,62

9,25

10,2

11,2

"EC" SUPPLY FANS

n. 1 1 1 1

1

Air flow

m³/h

6400

8700

10000

10800

Nominal external static pressure

Pa

20

Maximum external static pressure

Pa

665

512

175

332

Fans power input (4)

kW

1,19

1,42

2,1

2,08

ON/OFF COMPRESSORS

scroll

Compressors number

n. 1 1 1 1

1

Capacity steps

n. 1 1 1 1

1

Compressors power input

kW

5,55

6,2

7,16

8,1

9,13

AIR FILTERS

n. 2 2 2 2

2

Filter area

m2

1,24

2,07

Efficiency (ISO EN 16890)

COARSE

60%

REFRIGERANT CIRCUITS

n. 1 1 1 1

1

POWER SUPPLY

V/Ph/Hz

400/3+N/50

ENERGY EFFICIENCY INDEX (2) (5)

EER Energy Efficiency Ratio

kW/kW

3,89

4,27

4,06

4,05

DIMENSIONS

Length

mm

1085

1305

Width

mm

775

930

Height

mm

1925

1980

NET WEIGHT OVER

kg

338

462

467

479

487

NET WEIGHT UNDER

kg

358

472

477

489

497

REFRIGERANT CONNECTIONS

Gas delivery

ODS Ø

22

Liquid return

ODS Ø

16

22

HYDRAULIC CONNECTIONS

CONDENSATE DISCHARGE

Rubber pipe – internal diameter

Ø mm

19

THE COOLING CAPACITY DOES NOT CONSIDER THE SUPPLY FAN MOTOR THERMAL LOAD

1. U = Under, downflow / O = Over, upflow

2. Gross value. Characteristics referred to entering air at 26°C-40%RH; condensing temperature 45°C. ESP=20Pa.

3. SHR = Sensible cooling capacity / Total cooling capacity.

4. Corresponding to the nominal external static pressure

5. The Energy Efficiency Index does not consider the remote air-cooled condenser.

The units highlighted in this publication contain <HFC R410A [GWP

100

2088]> fluorinated greenhouse gas

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

16

MEHITS S.p.A.

DATA BOOK

TECHNICAL DATA

VERSION (1)

U / O

MODEL 039 P2 D

048 P2 D

055 P2 D

062 P2 D

075 P2 D

SIZE E5

E5

E6

E7

COOLING CAPACITY (2)

Total

kW

38,1

48,6

55,1

61,9

75,4

Sensible

kW

38,1

47,4

55,1

60,6

75,4

SHR (3) 1

0,98 1 0,98

1

Total power input (Comp. + Fans)

kW

9,21

12,5

13,5

15,1

17,9

"EC" SUPPLY FANS

n. 1 1 2 2

2

Air flow

m³/h

10000

12000

15000

15600

20000

Nominal external static pressure

Pa

20

Maximum external static pressure

Pa

259

206

654

592

438

Fans power input (4)

kW

1,82

2,31

2,4

2,68

3,6

ON/OFF COMPRESSORS

scroll

Compressors number

n. 2 2 2 2

2

Capacity steps

n. 2 2 2 2

2

Compressors power input

kW

7,39

10,2

11,1

12,4

14,3

AIR FILTERS

n. 3 3 3 3

4

Filter area

m2

2,59

3,16

3,82

Efficiency (ISO EN 16890)

COARSE

60%

REFRIGERANT CIRCUITS

n. 2 2 2 2

2

POWER SUPPLY

V/Ph/Hz

400/3+N/50

ENERGY EFFICIENCY INDEX (2) (5)

EER Energy Efficiency Ratio

kW/kW

4,14

3,89

4,08

4,10

4,21

DIMENSIONS

Length

mm

1630

1875

2175

Width

mm

930

Height

mm

1980

NET WEIGHT OVER

kg

584

594

684

704

777

NET WEIGHT UNDER

kg

594

604

694

714

834

REFRIGERANT CONNECTIONS

Gas delivery

ODS Ø

2x16

2x22

Liquid return

ODS Ø

2x16

2x22

HYDRAULIC CONNECTIONS

CONDENSATE DISCHARGE

Rubber pipe – internal diameter

Ø mm

19

THE COOLING CAPACITY DOES NOT CONSIDER THE SUPPLY FAN MOTOR THERMAL LOAD

1. U = Under, downflow / O = Over, upflow

2. Gross value. Characteristics referred to entering air at 26°C-40%RH; condensing temperature 45°C. ESP=20Pa.

3. SHR = Sensible cooling capacity / Total cooling capacity.

4. Corresponding to the nominal external static pressure

5. The Energy Efficiency Index does not consider the remote air-cooled condenser.

The units highlighted in this publication contain <HFC R410A [GWP

100

2088]> fluorinated greenhouse gas

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

17

MEHITS S.p.A.

DATA BOOK

TECHNICAL DATA

VERSION (1)

U / O

U / O U U

MODEL 082 P2 D

092 P2 D

102 P2 D

117 P4 D

146 P4 D

SIZE E7

E8

E9

COOLING CAPACITY (2)

Total

kW

82,5

92

104

122

147

Sensible

kW

79,5

88,1

94,9

122

140

SHR (3) 0,96

0,96

0,91 1 0,95

Total power input (Comp. + Fans)

kW

19,8

22,6

26,4

31,5

39

"EC" SUPPLY FANS

n. 2 2 2 3

3

Air flow

m³/h

20000

22000

32000

Nominal external static pressure

Pa

20

Maximum external static pressure

Pa

438

295

298

Fans power input (4)

kW

3,6

4,37

6,65

ON/OFF COMPRESSORS

scroll

Compressors number

n. 2 2 2 4

4

Capacity steps

n. 2 2 2 4

4

Compressors power input

kW

16,2

18,3

22

24,8

32,4

AIR FILTERS

n. 4 5 5 5

5

Filter area

m2

3,82

4,46

5,24

Efficiency (ISO EN 16890)

COARSE

60%

REFRIGERANT CIRCUITS

n. 2 2 2 2

2

POWER SUPPLY

V/Ph/Hz

400/3+N/50

ENERGY EFFICIENCY INDEX (2) (5)

EER Energy Efficiency Ratio

kW/kW

4,17

4,07

3,94

3,87

3,77

DIMENSIONS

Length

mm

2175

2499

2899

Width

mm

930

Height

mm

1980

NET WEIGHT OVER

kg

784

886

--

NET WEIGHT UNDER

kg

839

946

1150

1210

REFRIGERANT CONNECTIONS

Gas delivery

ODS Ø

2x22

2x28

Liquid return

ODS Ø

2x22

HYDRAULIC CONNECTIONS

CONDENSATE DISCHARGE

Rubber pipe – internal diameter

Ø mm

19

THE COOLING CAPACITY DOES NOT CONSIDER THE SUPPLY FAN MOTOR THERMAL LOAD

1. U = Under, downflow / O = Over, upflow

2. Gross value. Characteristics referred to entering air at 26°C-40%RH; condensing temperature 45°C. ESP=20Pa.

3. SHR = Sensible cooling capacity / Total cooling capacity.

4. Corresponding to the nominal external static pressure

5. The Energy Efficiency Index does not consider the remote air-cooled condenser.

The units highlighted in this publication contain <HFC R410A [GWP

100

2088]> fluorinated greenhouse gas

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

18

MEHITS S.p.A.

DATA BOOK

DUAL FLUID SYSTEM

DUAL FLUID system on the machine allows to obtain two independent cooling systems:

• Chilled water coil

• Direct expansion coil

The microprocessor control system automatically manages the system, by activating the cooling circuit more convenient according to the parameters set. With this system, it is possible, with a limited use of space, to solve several plant problems such as:

• Chilled water coil fed with chilled water or mains water as a stand-by of the main cooling

circuit.

• Double chilled water feeding with two independent circuit. This solution is used when you

need to ensure redundancy of the cooling system.

The temperature control is performed with the same logic of the main coil.

TECHNICAL DATA

VERSION (1)

U / O

MODEL 011 P1 S

014 P1 S

016 P1 S

020 P1 S

022 P1 S

SIZE E1

E2

E3

COOLING CAPACITY (2)

Total

kW

12,2

17,8

18,4

25,4

26,5

Sensible

kW

11,8

17,2

18

24,6

25,6

SHR (3) 0,97

0,97

0,98

0,97

COOLING COIL

Water flow rate (2)

m3/h

2,12

3,06

3,16

4,35

4,57

dP coil + valve (2)

kPa

15

33,5

35,6

24,7

26,6

Water volume

l

4,2

5,3

7,8

HYDRAULIC CONNECTIONS

WATER INLET / OUTLET ISO 7/1 - R

Ø

1"

1+1/4"

VERSION (1)

U / O

MODEL 026 P1 S

032 P1 S

037 P1 S

041 P1 S

045 P1 S

SIZE E3

E4

COOLING CAPACITY (2)

Total

kW

27,4

39

43,4

46

Sensible

kW

26,8

38,3

42

44,9

SHR (3) 0,98

0,98

0,97

0,98

COOLING COIL

Water flow rate (2)

m3/h

4,71

6,69

7,45

7,92

dP coil + valve (2)

kPa

28,3

14,2

17,1

19

Water volume

l

7,8

13,8

HYDRAULIC CONNECTIONS

WATER INLET / OUTLET ISO 7/1 - R

Ø

1+1/4"

1+1/2"

THE COOLING CAPACITY DOES NOT CONSIDER THE SUPPLY FAN MOTOR THERMAL LOAD

1. U = Under, downflow / O = Over, upflow

2. Characteristics referred to entering air at 26°C-40%RH with chilled water temperature 7-12°C - 0% glycol

3. SHR = Sensible cooling capacity / Total cooling capacity.

Air conditioner

Remote

condenser

Liquid chiller

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

19

MEHITS S.p.A.

DATA BOOK

TECHNICAL DATA

VERSION (1)

U / O

MODEL 039 P2 D

048 P2 D

055 P2 D

062 P2 D

075 P2 D

SIZE E5

E5

E6

E7

COOLING CAPACITY (2)

Total

kW

48,8

55,5

65,3

67,3

101

Sensible

kW

48,8

55,2

63,2

65,4

95,3

SHR (3) 1

0,99

0,97

0,94

COOLING COIL

Water flow rate (2)

m3/h

8,38

9,54

11,23

11,59

17,42

dP coil + valve (2)

kPa

26,3

33,1

15,7

16,6

38,8

Water volume

l

18,1

24,6

HYDRAULIC CONNECTIONS

WATER INLET / OUTLET ISO 7/1 - R

Ø

2"

2+1/2"

VERSION (1)

U / O

U / O U U

MODEL 082 P2 D

092 P2 D

102 P2 D

117 P4 D

146 P4 D

SIZE E7

E8

E9

COOLING CAPACITY (2)

Total

kW

101

116

136

Sensible

kW

95,3

108

136

SHR (3) 0,94

0,93

0,93 1 1

COOLING COIL

Water flow rate (2)

m3/h

17,42

19,9

23,43

dP coil + valve (2)

kPa

38,8

49,3

39,9

Water volume

l

24,6

28,5

33,8

HYDRAULIC CONNECTIONS

WATER INLET / OUTLET ISO 7/1 - R

Ø

2+1/2"

3”

THE COOLING CAPACITY DOES NOT CONSIDER THE SUPPLY FAN MOTOR THERMAL LOAD

1. U = Under, downflow / O = Over, upflow

2. Characteristics referred to entering air at 26°C-40%RH with chilled water temperature 7-12°C - 0% glycol

3. SHR = Sensible cooling capacity / Total cooling capacity.

2-WAY BALL VALVE FOR CHILLED WATER FLOW CONTROL

The water flow control in the finned coil is acieved through a 2-way modulating ball valve with equal percentage flow control ensured by the integrated characterizing disc.

This type of valve offers the following series of benefits:

• Equal percentage flow control.

• No peaks initial flow.

• Excellent stability control thanks to the integrated characterizing disc.

• Excellent characteristic in partialisation.

• Stability in control.

• Maintenance free.

• Self-cleaning.

CHARACTERISTICS OF THE 2-WAY BALL VALVE

• Closing seal with leakage rate in Class A (EN 12266-1)

• Maximum fluid pressure Ps=1600kPa

• Maximum closing pressure (Close-off) ∆Ps=1400kPa

The rotative actuator is controlled by a signal 0 … 10VDC from the microprocessor controller. The actuator is equipped with an emergency button for manual operation and is maintenance-free.

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

20

MEHITS S.p.A.

DATA BOOK

WATER QUALITY OF THE HYDRAULIC CIRCUITS

The values shown in the table must be guaranteed during the entire life cycle of the machine.

Description

Symbol

Range 1 Hydrogen Ions

pH

7.5 ÷ 9

2

Presence of calcium (Ca) and magnesium (Mg)

Hardness

4 ÷ 8.5 °D

3

Chlorine ions

Cl-

< 150 ppm

4

Iron Ions

Fe3+

< 0.5 ppm 5 Manganese Ions

Mn2+

< 0.05 ppm 6 Carbon dioxide

CO2

< 10 ppm

7

Hydrogen sulphide

H2S

< 50 ppb

8

Oxygen

O2

< 0.1 ppm 9 Chlorine

Cl2

< 0.5 ppm

10

Ammonia

NH3

< 0.5 ppm

11

Ratio between carbonates and sulphates

HCO3-/SO

4

2-

> 1

12

Sulphate ions

SO

4

--

< 100 ppm

13

Phosphate ions

PO

4

3-

< 2.0 ppm

where: 1/1.78°D = 1°Fr with 1°Fr = 10 gr CaCO3 / m3 ppm = parts for millions ppb = part for billion

Explanatory notes: ref.1: A greater concentration of hydrogen ions (pH) than 9 implies a high risk of deposits, whereas a lower pH than 7 implies a high risk of

corrosion.

ref.2: The hardness measures the amount of Ca and Mg carbonate dissolved in the water with a temperature lower than 100°C (temporary

hardness). A high hardness implies a high risk of deposits. ref.3: The concentration of chloride ions with higher values than those indicated causes corrosion. ref. 4 - 5 - 8: The presence of iron and manganese ions and oxygen leads to corrosion. ref.6 - 7: Carbon dioxide and hydrogen sulphide are impurities that promote corrosion. ref.9: Usually in water from the waterworks it is a value of between 0.2 and 0.3 ppm. High values cause corrosion. ref.10: The presence of ammonia reinforces the oxidising power of oxygen ref.11: Below the value shown in the table, there is a risk of corrosion due to the trigger of galvanic currents between copper and other less noble

metals. ref.12: The presence of sulphates ions triggers corrosion phenomenon. ref.13: The presence of phosphates ions triggers corrosion phenomenon.

It is necessary to carry out periodic checks, with withdrawals at different points of the hydraulic system. During the first year of operation, checks are recommended every 4 months which can be reduced every 6 months starting from the second year of operation.

WARNING: It is necessary that, in the presence of dirty and / or aggressive waters, an intermediate heat exchanger is installed upstream of the heat exchangers

ANTIFREEZE MIXTURES

In plants that are not adequately protected by heating cables, protect the hydraulic circuit with an anti-freeze mixture when the ambient air temperature can drop below 5°C.

The values are indicative and may significantly vary depending on the glycol manufacturer. Refer to your glycol supplier for detail. The values consider a precautionary difference of 5°C between the minimum ambient air temperature and the freezing temperature of the mixture.

In the hydraulic circuit do not send fluids other than water or mixtures with ethylene / propylene glycol. If other products are provided, in addition to mixtures of water and ethylene or propylene glycol, contact the Manufacturer to check the compatibility with the machine components.

Minimum ambient air temperature

°C 5 0

-5

-10

-15

-20

-25

-30

ETHYLENE GLYCOL (suggested % in weight)

% 0 12

20

30

35

40

45

50

Minimum ambient air temperature

°C 5 2

-3

-9

-13

-17

-23

-29

PROPYLENE GLYCOL (suggested % in weight)

% 0 10

20

30

35

40

45

50

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

21

MEHITS S.p.A.

DATA BOOK

REFRIGERANT CHARGE

The air conditioner is supplied with a minimum R410A refrigerant charge. Refrigerant must be charged. The following table shows the refrigerant charge that must be introduced for the air conditioner only. Remote condenser, connections pipes and optional are excluded.

VERSION (1)

U / O

MODEL 011 P1 S

014 P1 S

016 P1 S

020 P1 S

022 P1 S

SIZE E1

E2

E3

REFRIGERANT

R410A

Refrigerant circuits x Refrigerant charge (2)

n x kg

1 x 3,2

1 x 3,4

1 x 4,0

HFC R410A - F Gas - CO2 equivalent

t

6,68

7,10

8,35

VERSION (1)

U / O

MODEL 026 P1 S

032 P1 S

037 P1 S

041 P1 S

045 P1 S

SIZE E3

E4

REFRIGERANT

R410A

Refrigerant circuits x Refrigerant charge (2)

n x kg

1 x 4,0

1 x 5,7

1 x 8,6

HFC R410A - F Gas - CO2 equivalent

t

8,35

11,90

17,96

VERSION (1)

U / O

MODEL 039 P2 D

048 P2 D

055 P2 D

062 P2 D

075 P2 D

SIZE E5

E5

E6

E7

REFRIGERANT

R410A

Refrigerant circuits x Refrigerant charge (2)

n x kg

2 x 4,5

2 x 4,9

2 x 8,1

HFC R410A - F Gas - CO2 equivalent

t

18,79

20,46

33,83

VERSION (1)

U / O

U / O U U

MODEL 082 P2 D

092 P2 D

102 P2 D

117 P4 D

146 P4 D

SIZE E7

E8

E9

REFRIGERANT

R410A

Refrigerant circuits x Refrigerant charge (2)

n x kg

2 x 8,1

2 x 8,7

2 x 10,8

HFC R410A - F Gas - CO2 equivalent

t

33,83

36,33

45,1

1. U = Under, downflow / O = Over, upflow

2. Refrigerant charge required for the air conditioner only operation. Remote condenser, connections pipes and optional are excluded.

For air conditioners with double refrigerant circuit is indicated the number of circuits x the charge of a single circuit.

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

22

MEHITS S.p.A.

DATA BOOK

PRESSURE RELIEF VALVE

The pressure relief valve of the refrigerant circuit is installed in the machines when required by Directive 2014/68/EU. The valve is installed on liquid receiver of each refrigerant circuit of the machine with the purpose to protect the circuit from overpressure.

It is up to the installer to check whether the system complies with the 2014/68 / EU standard regarding the installation of the pressure relief valve. By plant we mean the complete system that includes the internal machine, the remote condenser and the connecting pipes

The installer must calculate the amount of refrigerant contained in the system and, if the refrigerant charge is higher than 10 kg, he must install the pressure relief valve.

Factory installed

components

At Installer care

Pressure relief valve on

liquid receiver

Possible pressure relief

valve

Model

[bar]

011 P1 S

---

41,5

014 P1 S

---

41,5

016 P1 S

---

41,5

020 P1 S

---

45,0

022 P1 S

---

45,0

026 P1 S

---

45,0

032 P1 S

---

45,0

037 P1 S

---

45,0

041 P1 S

45,0

---

045 P1 S

45,0

---

039 P2 D

---

45,0

048 P2 D

---

45,0

055 P2 D

---

45,0

062 P2 D

---

45,0

075 P2 D

45,0

---

082 P2 D

45,0

---

092 P2 D

45,0

---

102 P2 D

45,0

---

117 P4 D

45,0

---

146 P4 D

45,0

---

Exhaust flow CONNECTION Ø 3/4” G – M

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

23

MEHITS S.p.A.

DATA BOOK

R1

EVP

RU

C1

SPH1

BPH1

BPL1

IP

FG

VE

IP

FG

VE1

T1

RL

VS

CND1

RU

M1

DF

T2

Tin

R1

EVP

RU

C1

SPH1

BPH1

BPL1

IP

FG

VE

IP

FG

VE1

T1

RL

VS

CND1

RU

M1

DF

T2

Tin

REFRIGERANT CIRCUIT

Below refrigerant diagrams for version with single or double refrigerant circuit. The diagrams refer to the standard configuration, without optional.

UNDER - SINGLE REFRIGERANT CIRCUIT

OVER - SINGLE REFRIGERANT CIRCUIT

LEGENDA C1 Compressor R1 Crankcase heater CND Condenser. EVP Evaporator EC Dual fluid Chilled water coil

BPH High pressure transducer. BPL Low pressure transducer. SPH High pressure switch M1 Dual-Fluid 2-way valve VS Pressure relief valve. FG Refrigerant filter.

IP Sight glass. VE Expansion valve. T Temperature probes. RU Valves RL Liquid receiver

VS = Pressure relief valve Only models 041 P1, 045 P1

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

24

MEHITS S.p.A.

DATA BOOK

R1

R2

IP

EVP

FG

RU

VE

C1

SPH1

BPH1

BPL1

VS

C2

SPH2

BPH2

BPL2

IP

FG

VE2

IP

FG

RU

VE

IP

FG

VE1

RL

VS

CND1

RU

CND2

RU

T1

M1

DF

T2

Tin

R1

R2

IP

EVP

FG

RU

VE

C1

SPH1

BPH1

BPL1

VS

C2

SPH2

BPH2

BPL2

IP

FG

VE2

IP

FG

RU

VE

IP

FG

VE1

T1

RL

VS

CND1

RU

CND2

RU

M1

DF

T2

Tin

R2

R1

C2

C1

R2

R1

C2

C1

UNDER - DOUBLE REFRIGERANT CIRCUIT

OVER - DOUBLE REFRIGERANT CIRCUIT

LEGENDA C1 Compressor R1 Crankcase heater CND Condenser. EVP Evaporator EC Dual fluid Chilled water coil

BPH High pressure transducer. BPL Low pressure transducer. SPH High pressure switch M1 Dual-Fluid 2-way valve VS Pressure relief valve. FG Refrigerant filter.

IP Sight glass. VE Expansion valve. T Temperature probes. RU Valves RL Liquid receiver

VS = Pressure relief valve Only models 075 P2, 082 P2, 092 P2, 102 P2, 117 P4, 146 P4

VS = Pressure relief valve Only models 075 P2, 082 P2, 092 P2, 102 P2

SIZE E9

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

25

MEHITS S.p.A.

DATA BOOK

RECOMMENDED REFRIGERANT LINES

Values are referred to “EQUIVALENT LENGTH” of the piping. You are kindly requested to always refer to the “INSTALLATION DIAGRAM” for the allowable height difference and to properly select all necessary components. Verify the need to use pressure limiting devices (pressure relief valves) where not already provided for by Directive 2014/68 / EU.

In some cases, the diameter of the refrigerant lines may not correspond with the diameter of the cooling taps. This is completely normal. It is enough to provide a reduction fitting to adjust the diameter.

Model

Capacity

for single

circuit

[kW]

Line

Nominal

Ø [mm]

EQUIVALENT LENGHT [m] FOR ON / OFF COMPRESSORS R410A

5

10

15

20

25

30

35

40

45

50

011

P1 S

11

Gas

12

12 mm

16 mm

Liquid

12

12 mm

16 mm

014

P1 S

14

Gas

16

16 mm

Liquid

12

12 mm

16 mm

016

P1 S

16

Gas

16

16 mm

Liquid

12

12 mm

16 mm

020

P1 S

20

Gas

16

16 mm

18 mm

Liquid

16

16 mm

022

P1 S

22

Gas

16

16 mm

18 mm

Liquid

16

16 mm

18 mm

026

P1 S

26

Gas

22

22 mm

Liquid

16

16 mm

18 mm

032

P1 S

32

Gas

22

22 mm

Liquid

16

16 mm

18 mm

22 mm

037

P1 S

37

Gas

22

22 mm

Liquid

16

16 mm

18 mm

22 mm

041

P1 S

41

Gas

22

22 mm

Liquid

22

22 mm

045

P1 S

45

Gas

22

22 mm

28 mm

Liquid

22

22 mm

039

P2 D

19,5

Gas

16

16 mm

18 mm

Liquid

16

16 mm

048

P2 D

24

Gas

16

16 mm

18 mm

Liquid

16

16 mm

18 mm

055

P2 D

27,5

Gas

22

22 mm

Liquid

16

16 mm

18 mm

062

P2 D

31

Gas

22

22 mm

Liquid

16

16 mm

18 mm

22 mm

075

P2 D

37,5

Gas

22

22 mm

Liquid

22

22 mm

082

P2 D

41

Gas

22

22 mm

Liquid

22

22 mm

092

P2 D

46

Gas

22

22 mm

28 mm

Liquid

22

22 mm

102

P2 D

51

Gas

22

22 mm

28 mm

Liquid

22

22 mm

117

P4 D

58,5

Gas

28

28 mm

Liquid

22

22 mm

28 mm

146

P4 D

73

Gas

28

28 mm

Liquid

22

22 mm

28 mm

For equivalent lengths over 50m, please contact the Manufacturer's Sales Office.

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

26

MEHITS S.p.A.

DATA BOOK

INSTALLATION DIAGRAM

WARNING It is necessary to provide the refrigerant charge for the connection pipes and for the remote air-cooled condenser. Charge refrigerant in the suitable quantity and lubricant oil in 10% ratio of charged refrigerant. Lubricant oil must be the same type as the charged one as shown on the compressor plate.

CARRY OUT PIPING WITH SLOPES INDICATED TO FAVOR THE RETURN OF THE LUBRICANT OIL TO THE COMPRESSOR

APPLY THE DIAGRAM TO ANY REFRIGERANT CIRCUIT OF THE MACHINE.

Difference in height between the machine and the remote condenser: Value expressed in equivalent length

LEGENDA

1. Air conditioner

2. Remote air-cooled condenser

3. Gas discharge line

4. Liquid return line

5. Trap. Foresee a trap every 5m of the rising pipe.

6. Additional liquid receiver, external to the machine –

By the installer. It is suggested for:

- Plants with refrigerant lines with an equivalent length of more

than 25 meters

- Plants with refrigerant lines of any length and operating at

outdoor temperatures below 0°C.

7. “601 Solenoid valve on liquid line”. Optional accessory of the

machine, suggested for plants with refrigerant pipe longer than 10m.

8. Check valve – By the Installer. The valve must be installed on the

liquid line close to the condenser. The valve prevents the return of liquid in the condenser, particularly in the case of plant shutdown during the winter season.

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

27

MEHITS S.p.A.

DATA BOOK

ACOUSTIC DATA

Acoustic data of the standard machine at full load working conditions.

WARNING:

In a closed room the noise produced by a sound source reaches the listener in two different ways:

• Directly

• Reflected from the surrounding walls, floor, ceiling, from furniture.

With the same sound source, the noise produced in a closed room is greater than that produced outdoors. In fact, the sound pressure level generated by the source, must be added to the one reflected from the room. Also, the shape of the room affects the sound.

MODEL

011 P1 S

014 P1 S

016 P1 S

020 P1 S

022 P1 S

026 P1 S

SIZE E1

E2

E3

SOUND LEVEL ISO 3744 (1)

On air delivery, Under

dB(A)

64,7

70,8

71,9

70,3

71,8

72,8

On air intake, Under

dB(A)

55,9

56,9

58,1

57,0

58,9

59,2

On front side, Under

dB(A)

47

48

49

48

50

On air delivery, Over

dB(A)

64,7

70,8

71,9

70,3

71,8

72,8

On air intake, Over (2)

dB(A)

52

54

55

59

57

On front side, Over (3)

dB(A)

41,8

47,1

48,1

46,7

48,7

49,0

MODEL

032 P1 S

037 P1 S

041 P1 S

045 P1 S

039 P2 D

048 P2 D

SIZE E4

E4

E5

SOUND LEVEL ISO 3744 (1)

On air delivery, Under

dB(A)

78,1

81,1

78,9

81,3

81,5

On air intake, Under

dB(A)

64,2

67,1

66,4

67,3

69,0

On front side, Under

dB(A)

55

58

57

58

60

On air delivery, Over

dB(A)

78,1

81,1

78,9

81,3

81,5

On air intake, Over (2)

dB(A)

61

63

62

63

64

On front side, Over (3)

dB(A)

54,3

57,3

56,8

57,6

59,4

MODEL

055 P2 D

062 P2 D

075 P2 D

082 P2 D

092 P2 D

102 P2 D

SIZE E6

E6

E7

E8

SOUND LEVEL ISO 3744 (1)

On air delivery, Under

dB(A)

77,9

78,7

80,1

82,5

On air intake, Under

dB(A)

64,1

65,0

67,8

70,1

On front side, Under

dB(A)

55

56

58

61

On air delivery, Over

dB(A)

77,9

78,7

80,1

82,5

On air intake, Over (2)

dB(A)

61

62

64

66

67

On front side, Over (3)

dB(A)

54,1

55,0

58,1

60,4

MODEL

117 P4 D

146 P4 D

SIZE E9

E9

SOUND LEVEL ISO 3744 (1)

On air delivery, Under

dB(A)

83,4

On air intake, Under

dB(A)

70,9

On front side, Under

dB(A)

62

On air delivery, Over

dB(A)

--

On air intake, Over (2)

dB(A)

--

On front side, Over (3)

dB(A)

--

1. Noise pressure level at 1 meter in free field – ISO 3744

2. Air intake from the front

3. Air intake from the bottom

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

28

MEHITS S.p.A.

DATA BOOK

ELECTRICAL DATA

Electrical data of the system at full load working conditions.

VERSION (1)

U / O

MODEL 011 P1 S

014 P1 S

016 P1 S

020 P1 S

022 P1 S

SIZE E1

E2

E3

Power supply

V/ph/Hz

400/3+N/50

Maximum current input (FLA)

A

7,65

10,0

11,5

15,2

19,2

VERSION (1)

U / O

MODEL 026 P1 S

032 P1 S

037 P1 S

041 P1 S

045 P1 S

SIZE E3

E4

Power supply

V/ph/Hz

400/3+N/50

Maximum current input (FLA)

A

20,4

22,4

25,8

29,4

35,4

VERSION (1)

U / O

MODEL 039 P2 D

048 P2 D

055 P2 D

062 P2 D

075 P2 D

SIZE E5

E5

E6

E7

Power supply

V/ph/Hz

400/3+N/50

Maximum current input (FLA)

A

26,2

34,4

40,8

44,8

52,1

VERSION (1)

U / O

U / O U U

MODEL 082 P2 D

092 P2 D

102 P2 D

117 P4 D

146 P4 D

SIZE E7

E8

E9

Power supply

V/ph/Hz

400/3+N/50

Maximum current input (FLA)

A

58,9

70,9

76,9

86,1

113,0

1. U = Under, downflow / O = Over, upflow

WARNING: The electric data indicated refer only to the indoor unit. Optional accessory electric data are included within the dedicated chapters and must be added. Please refer to ELCA WORLD selection program to calculate the electrical data of the air conditioner according to the requested optional accessories. The remote air-cooled condenser is not included because it has independent power supply.

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

29

MEHITS S.p.A.

DATA BOOK

MICROPROCESSOR CONTROL SYSTEM

The unit is equipped with the controller connected to a 6 keys keyboard with graphic display on which all information in English language or easily identifiable symbols are displayed. The controller disposes of a “flash” memory that preserves the information even in absence of power supply. Part of memory is dedicated to the registration of intervened events - up to 200 events.

DISPLAY – KEYBOARD FUNCTIONS

DISPLAY - MAIN MASK

The main mask shows time, date, room temperature and humidity values (if the relative probe is present) and areas for displaying operating and alarm status with dedicated icons:

CONNECTIVITY

Through the optional serial port, the microprocessor control enables communication with the modern buildings BMS systems with the following protocols: MODBUS; LON; BACNET MS/TP RS485; BACNET OVER IP.

PASSWORD

Level 1: On request of the End User. Allowing to reach USER menu Level 2: Asks to Service: Allowing to reach SERVICE menu Level 3: Asks to Service: Allowing to reach FACTORY menu No passwords request to enter: UNIT, SETPOINT, IN/OUT, CLOCK, HISTORY menu

ALARM

Alarm presence with red light. Push for alarm description. In case of more alarms scroll by UP / DOWN.

PRG

Menu list, scrolled by UP/DOWN:

Unit; Set-point; In/Out; Clock; History; User; Service; Factory. ENTER to execute.

ESC

Home. Used to come back to the previous menu level or to the main screen.

UP DOWN

Changes pages and values of sets. By pressing in HOME mask, the synoptic of the main controls is displayed.

ENTER

Moving the cursor on adjustable Program(s) fields to confirm the changes. Press ENTER to get out the fields.

Controller

Keyboard and Display

Y Y D

D

Area 1: Status of the unit: on / off Area 2: Status detail Area 3: Type of event (only in case of an event) Area 3_A: Code and type of event Area 4: Active cooling devices Area 5: Active free-cooling devices Area 6: Active humidity devices

Area 7: Active heating devices Area 8: on / off parameters Area 9: BMS address Area 10: LAN address Area 11: Schematic representation of units Area 12: Active function presence icon

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

30

MEHITS S.p.A.

DATA BOOK

LAN NETWORK

The LAN is part of the control software and it is possible to connect up to 10 units. This type of connection allows to control the units in coherent way, moreover the units can be controlled and managed from a shared remote terminal.

LAN ADDRESS LIST

Unit # 1 2 3 4 5 6 7 8 9 10

Remote Terminal

Mother board address

1 2 3 4 5 6 7 8 9

10

--

Terminal address

11

12

13

14

15

16

17

18

19

20

32

The unit connection to the local network (LAN) allows to perform the following functions:

• Balancing the operating hours among the different units by rotating the reserve units (Stand-by)

• Turning on the reserve units in case other units should turn off due to an alarm, maintenance or

power feed interruption

• Turning on reserve units to offset the excessive thermal load

• Checking up to 10 units with a single user terminal (shared user terminal)

Humidifier

control

Network

analyser

T Probe

T/H probe

Additional T/H

probe

Expansion

board 1

Expansion

board 2

Expansion

board 3

EEV 1

controller

EEV 2

controller

Fan 2 Fan 3 Fan

1

Controller

backup module

MODBUS

BACnet

OVER IP

LON

BACnet

MS/TP RS485

BMS 1

Display & Keyboard

LAN address=11

Controller - LAN address=1

FieldBus2

LAN address=2

LAN address=12

UNIT 2

LAN address=3

LAN address=13

UNIT 3

LAN address=10

LAN address=20

UNIT 10

LAN address=32

REMOTE

TERMINAL

UNIT 1

LAN

Diagram in maximum configuration

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

31

MEHITS S.p.A.

DATA BOOK

DEMAND LIMIT

Demand Limit function is part of the control software for machines with double refrigerant circuit. It allows to limit the absorbed current of the machine. The function must be activated and configurated. A digital inlet on electrical panel connecting terminals allows the remote enabling of the function with an external signal without tension. The software allows to select the resources to disable (compressors, electric heaters,…).

TEMPERATURE PROBE ON AIR RETURN / DELIVERY

Temperature probe installed on the air return and delivery. Temperature control and regulation function on air return.

CLOGGED FILTERS SENSOR

The system includes a differential pressure switch installed in the electrical panel or in the front of the indoor unit and the plastic hoses for the relief of the pressure upstream and downstream the air filters.

Control range: 0.3 … 4.0 mbar (30 … 400 Pa) Differential for intervention: 0.15 mbar (15 Pa)

FLOOD SENSOR

The system includes an electronic relay installed in the electrical panel of the machine and a water detector. The electrical connections for the probe and the alarm contact are present in the machine's terminal board. Sensor is supplied to be connected and installed at customer care.

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

32

MEHITS S.p.A.

DATA BOOK

80

250

70

70 70

A

125

130

70 A 70

POSSIBLE AIR INTAKE FOR OVER VERSIONS

OVER VERSION - AIR INTAKE FROM THE BOTTOM Thanks to the particular basement design, it is possible to have the unit air intake from the bottom side. With this solution, it is necessary to foresee the optional blind frontal panels

OVER VERSION - AIR INTAKE FROM THE BACK SIDE (Sizes E4, E5, E6, E7, E8, E9 excluded) It is possible to have the unit air intake from the back side. Due to the limited size of the air intake, the air flow is limited to the 20% of the nominal one. The air intake must be made by Customer during installation. In case the air intake is used for fresh air, it is necessary the temperature / humidity probe reposition in front of the heat exchanger, to allow for optimum reading of the values of temperature / humidity. The electric cable of the probe has enough length for the repositioning.

GRANDEZZA

E1

E2

E3

A

mm

510

645

945

Max air flow

m3/h

600

1000

1500

AIR INTAKE FROM THE BACK SIDE

Back side view

OVER

E1 – E2 – E3

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

33

MEHITS S.p.A.

DATA BOOK

REMOTE AIR-COOLED CONDENSER

Remote air-cooled condensers for matching to air conditioners for IT Cooling. The constructive solutions allow high application flexibility. Horizontal air flow, from coil to fan. The series has an independent power supply from the indoor unit. Among the indoor unit and the condenser is necessary the refrigerant connection and electrical connection of the condensing proportional control signal and the alarms.

Is available the optional “P191 power supply for condenser” from the indoor machine electrical board. The optional includes magnetothermic switches for condenser fans.

P821 / P831 / P841 / P851 – GR-Z SERIES

The machines are made with Peraluman aluminium alloy and suitable for outdoor installation.

GR-Z A B 50: Remote condenser equipped with AC fan, microchannel condensing coil and Standard acoustic version. GR-Z A L 50: Remote condenser equipped with AC fan, microchannel condensing coil and Low noise acoustic version. GR-Z E B 50: Remote condenser equipped with EC fan, microchannel condensing coil and Standard acoustic version. GR-Z E L 50: Remote condenser equipped with EC fan, microchannel condensing coil and Low noise acoustic version.

IMPORTANT For further information about the units, please refer to “GR-Z” series Data Books.

MATCHING

REMOTE AIR-COOLED CONDENSERS FOR OUTDOOR INSTALLATION EQUIPPED WITH AC AXIAL FANS.

MODEL

011

P1 S

014

P1 S

016

P1 S

020

P1 S

022

P1 S

026

P1 S

032

P1 S

037

P1 S

041

P1 S

045

P1 S

CONDENSER

n. 1 1 1 1 1 1 1 1 1 1

GR-Z A B 50

Mod.

013

024

027

034

049

055

GR-Z A L 50

Mod.

011

018

025

036

043

051

MODEL

039

P2 D

048

P2 D

055

P2 D

062

P2 D

075

P2 D

082

P2 D

092

P2 D

102

P2 D

117

P4 D

146

P4 D

CONDENSER

n. 2 2 2 2 2 2 2 2 2 2

GR-Z A B 50

nxMod.

2x024

2x027

2x034

2x049

2x055

2x067

2x082

GR-Z A L 50

nxMod.

2x021

2x036

2x043

2x051

2x063

2x086

REMOTE AIR-COOLED CONDENSERS FOR OUTDOOR INSTALLATION EQUIPPED WITH EC AXIAL FANS.

MODEL

011

P1 S

014

P1 S

016

P1 S

020

P1 S

022

P1 S

026

P1 S

032

P1 S

037

P1 S

041

P1 S

045

P1 S

CONDENSER

n. 1 1 1 1 1 1 1 1 1 1

GR-Z E B 50

Mod.

015

024

027

034

049

055

GR-Z E L 50

Mod.

011

018

025

036

043

051

MODEL

039

P2 D

048

P2 D

055

P2 D

062

P2 D

075

P2 D

082

P2 D

092

P2 D

102

P2 D

117

P4 D

146

P4 D

CONDENSER

n. 2 2 2 2 2 2 2 2 2 2

GR-Z E B 50

nxMod.

2x024

2x027

2x034

2x049

2x055

2x067

2x082

GR-Z E L 50

nxMod.

2x021

2x036

2x043

2x051

2x063

2x086

WARNING: Please refer to ELCA WORLD selection program to calculate the cooling capacity of the air conditioner according to the selected remote condenser.

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

34

MEHITS S.p.A.

DATA BOOK

T-MATE DX SERIES

T-MATE DX: Remote air-cooled condensers equipped with axial fans and condensing coil with copper

tubes and aluminium fins. The machines are suitable for outdoor installation.

A Version: Equipped with AC axial fans. E Version: Equipped with EC axial fans.

The series is available in 3 versions:

• STD - No air flow and sound level reduction.

• LNO - Air flow reduction at 85% with consequent sound level reduction.

• ELN - Air flow reduction at 70% with further sound level reduction.

T-MATE DX-PF-E: Remote air-cooled condensers equipped with EC plug fans and condensing coil with copper tubes and aluminium fins. The machines are designed for indoor installation and ducting for air suction and discharge. For outdoor installation, the machine must be installed under a cover or anyway protected against atmospherics agent.

IMPORTANT For further information about the units, please refer to “T-MATE” series Data Books.

MATCHING

REMOTE AIR-COOLED CONDENSERS FOR OUTDOOR INSTALLATION EQUIPPED WITH AC AXIAL FANS.

MODEL

011

P1 S

014

P1 S

016

P1 S

020

P1 S

022

P1 S

026

P1 S

032

P1 S

037

P1 S

041

P1 S

045

P1 S

CONDENSER

n. 1 1 1 1 1 1 1 1 1 1

T-MATE DX-A STD

Mod.

M11

M14

M17

M25

M30

M35

M45

M50

T-MATE DX-A LNO

Mod.

M14

M17

M25

M30

M45

M50

M60

M70

T-MATE DX-A ELN

Mod.

M14

M17

M25

M30

M45

M50

M60

M70

MODEL

039

P2 D

048

P2 D

055

P2 D

062

P2 D

075

P2 D

082

P2 D

092

P2 D

102

P2 D

117

P4 D

146

P4 D

CONDENSER

n. 2 2 2 2 2 2 2 2 2 2

T-MATE DX-A STD

nxMod.

2xM25

2xM30

2xM35

2xM45

2xM50

2xM60

2xM70

2xM95

T-MATE DX-A LNO

nxMod.

2xM30

2xM45

2xM50

2xM60

2xM70

2xM95

T-MATE DX-A ELN

nxMod.

2xM30

2xM45

2xM50

2xM60

2xM70

2xM95

2xM110

REMOTE AIR-COOLED CONDENSERS FOR OUTDOOR INSTALLATION EQUIPPED WITH EC AXIAL FANS.

MODEL

011

P1 S

014

P1 S

016

P1 S

020

P1 S

022

P1 S

026

P1 S

032

P1 S

037

P1 S

041

P1 S

045

P1 S

CONDENSER

n. 1 1 1 1 1 1 1 1 1 1

T-MATE DX-E STD

Mod.

T11

T14

T17

T25

T30

T35

T45

T50

T-MATE DX-E LNO

Mod.

T14

T17

T25

T30

T45

T50

T60

T70

T-MATE DX-E ELN

Mod.

T14

T17

T25

T30

T45

T50

T60

T70

MODEL

039

P2 D

048

P2 D

055

P2 D

062

P2 D

075

P2 D

082

P2 D

092

P2 D

102

P2 D

117

P4 D

146

P4 D

CONDENSER

n. 2 2 2 2 2 2 2 2 2 2

T-MATE DX-E STD

nxMod.

2xT25

2xT30

2xT35

2xT45

2xT50

2xT60

2xT70

2xT95

T-MATE DX-E LNO

nxMod.

2xT30

2xT45

2xT50

2xT60

2xT70

2xT95

T-MATE DX-E ELN

nxMod.

2xT30

2xT45

2xT50

2xT60

2xT70

2xT95

2xT110

REMOTE AIR-COOLED CONDENSERS FOR INDOOR INSTALLATION EQUIPPED WITH EC PLUG FANS.

MODEL

011

P1 S

014

P1 S

016

P1 S

020

P1 S

022

P1 S

026

P1 S

032

P1 S

037

P1 S

041

P1 S

045

P1 S

CONDENSER

n 1 1 1 1 1 1 1 1 1 1

T-MATE DX-PF-E STD

Mod.

T11

T14

T21

T24

T33

T38

T44

T58

MODEL

039

P2 D

048

P2 D

055

P2 D

062

P2 D

075

P2 D

082

P2 D

092

P2 D

102

P2 D

117

P4 D

146

P4 D

CONDENSER

n 2 2 2 2 2 2 2 2 2 2

T-MATE DX-PF-E STD

nxMod.

2xT24

2xT33

2xT38

2xT58

2xT69

2xT86

WARNING: Please refer to ELCA WORLD selection program to calculate the cooling capacity of the air conditioner according to the selected remote condenser.

T-MATE DX-A T-MATE DX-E

T-MATE DX-PF-E

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

35

MEHITS S.p.A.

DATA BOOK

1

2

4

3

OPTIONAL ACCESSORIES: P121 – FRONT AIR INTAKE+BOTTOM PANEL

Available for OVER units. The optional is not compatible with “P122 Bottom air intake+blind panels” for OVER units. With this accessory, it is possible a noise insulation of the machine base, when the machine is installed directly on floor as raised floor, wood floor etc. The accessory includes:

• Panel in galvanized steel sheet.

• Noise insulation with special soundproof material.

The bottom panel is supplied assembled inside the unit base and does not modify the unit dimensions.

OPTIONAL ACCESSORIES: 601 – SOLENOID VALVE ON LIQUID LINE

The accessory has the function of closing the liquid line, in the event of the machine stopping or blackout, avoiding the risk of liquid refrigerant migration into the evaporator. Recommended accessory for:

- Refrigerating lines greater than 10m in equivalent length.

- Machines equipped with electronic expansion valve.

OPTIONAL ACCESSORIES: A548 - CONSTANT PREVALENCE

The optional is a differential pressure sensor with a 0…20mA output signal. The device is installed in the machine. The sensor is connected to the microprocessor control of the indoor unit and allows the control of:

A548 - CONSTANT PREVALENCE The system controls the air pressure in the raised floor (Under version) or in the duct (Over version). Through the relief piping of the room pressure (low pressure side) and the air supply of the fan (high pressure side) the fan rotation speed is controlled to keep the air pressure constant. Pressure control range from 0 to 100 Pa.

OPTIONAL ACCESSORIES: P091 - BACK-UP MODULE CONTROLLER

The optional is installed within the electrical panel. The optional is not available for size E1. The system powers the microprocessor for a few minutes in the event of a power failure or voltage surges, preventing the re-boot of the controller.

1. Air conditioner

2. Air conditioner base

3. Bottom panel

4. Insulation with special sound

soundproof material

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

36

MEHITS S.p.A.

DATA BOOK

R1

EVP

RU

C1

BPH1

BPL1

IP

VE

IP

FG

VE1

CND1

RU

T2

SPH1

YR2

RL

VS

YR1

T1

M1

DF

Tin

OPTIONAL ACCESSORIES: P171 – KIT FOR AIR -45°C MCH AXIAL AC OPTIONAL ACCESSORIES: P172 – KIT FOR AIR -45°C AXIAL AC

P171 – LOW TEMPERATURE KIT MCH AXIAL AC (GR-Z A B 50) P172 – LOW TEMPERATURE KIT AXIAL AC (T-MATE DX-A STD)

The optional is available only for air conditioners matched with remote air-cooled condensers with axial fans with AC electric motors:

• T-MATE DX-A STD. Condensing coil with copper tubes and aluminium fins. Standard

acoustic version, up to M140 model included.

• GR-Z A B 50. Condensing coil with microchannel coils.

Standard acoustic version.

The system is necessary for the correct machine start up and operation with very low ambient air temperatures: between -20°C and -45°C.

Components for each refrigerant circuit:

• A check valve (YR

1

), supplied in kit. The valve must be installed indoor, near to the air conditioner, on the liquid line on the return of the remote condenser. This valve avoids the migration of the refrigerant at liquid state in presence of very low ambient air condition.

• A check valve (YR

2

), with controlled opening, installed in factory within the unit. It limits the pressure raising on the liquid pipe between the expansion valve and the check valve (YR1).

Electrical components installed on the electric board of the indoor unit, only for optional accessory P172 LOW TEMPERATURE KIT AXIAL AC (T-MATE DX-A STD):

• Electronic phase-cut regulators for fans speed control;

• Terminals for electric connections to the remote condenser;

• Electrical power supply for remote condenser from the indoor machine electrical board.

The optional “P172 Kit for air -45°C axial AC” requires mandatory accessory “P191 Power supply for condenser”.

LEGENDA C1 Compressor R1 Crankcase heater CND Condenser. EVP Evaporator. DF Dual Fluid coil. M1 Dual Fluid 2-way valve. BPH High pressure transducer. BPL Low pressure transducer. SPH High pressure switch VS Pressure relief valve on model:

041 / 045 P1 S 075 / 082 / 092 / 102 P2 D

117 / 146 P4 D FG Refrigerant filter. IP Sight glass. VE Expansion valve. T Temperature probes. RU Valves RL Liquid receiver YR1 Check valve to be installed on the

liquid line close to the machine

inside the room YR2 Unidirectional check valve with

controlled opening that limits

pressure rising on the liquid line

Optional,

supplied in kit

Optional

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

37

MEHITS S.p.A.

DATA BOOK

OPTIONAL ACCESSORIES: A492 – WATER LEACKAGE DETECTOR + ADDITIONAL DETECTOR

The system includes an electronic relay installed in the electrical panel of the indoor machine and 2 water detectors to be connected in series. The electrical connections for the probe and the alarm contact are present in the indoor machine's terminal board. The sensors are supplied to be connected and installed at customer care.

OPTIONAL ACCESSORIES: A511 - SMOKE DETECTORS

OPTIONAL ACCESSORIES: A512 – FIRE DETECTORS

Is possible to install one or both of the following sensors. Sensors are supplied in mounting kit. Installation within the room at customer care.

A511 - SMOKE DETECTOR

The device in supplied in mounting kit. The optical smoke detector senses the presence of combustion by-products (visible smoke) and activates an alarm. The operating principle is based on the light scattering technique (Tyndall effect). The device is in conformity to EN 54-7 standard. Technical features:

Supplied with unit to be connected and installed at customer care close to the unit.

A512 - FIRE DETECTOR

The device in supplied in mounting kit. The fire detector has been designed to identify temperatures at which fires may start. When the temperature exceeds the set threshold or when there is a rapid variation in temperature, the relay is activated to signal an alarm. The device is in conformity to EN 54-5 standard. Technical features:

Supplied with unit to be connected and installed at customer care close to the unit.

Material

ABS Relative humidity

<93% not-condensing

Power supply

12...28 Vdc

Index of protection

IP 20

Normal current

50μA 24 Vdc

Testing by magnet

Yes

Alarm current

25mA 24 Vdc

Relay

max. 1A 30Vdc

LED visibility

360° (double led)

Signal repeater

14mA 24 Vdc

Storage temperature

-10…+70°C

Covered area

40m2 max.

Operating temperature

-10…+70°C

Shielded connection

Min. 0.5 mm2

Max. speed air

0.2 m/s

Colour

White

Material

ABS Index of protection

IP 20

Power supply

12...28 Vdc

Testing by magnet

Yes

Normal current

50μA 24 Vdc

Relay

max. 1A 30Vdc

Alarm current

25mA 24 Vdc

Signal repeater

14mA - 24 Vdc

LED visibility

360° (double LED)

Alarm temperature

62°C

Storage temperature

-10…+70°C

Covered area

40m2 max.

Operating temperature

-10…+70°C

Shielded connection

Min. 0.5 mm2

Relative humidity

<93% non-condensing

Colour

White

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

38

MEHITS S.p.A.

DATA BOOK

ACCESSORI: P181 – ANALIZZATORE DI RETE

ACCESSORI: P182 – ANALIZZATORE DI RETE+OPTIONAL

ACCESSORI: P183 – KIT ANALIZZATORE DI RETE

ACCESSORI: P184 – KIT ANALIZZATORE DI RETE+ OPTIONAL

This device provides continuous measurement of power consumption, monitoring current, voltage and power. These values are sent to unit microprocessor via RS485 serial cable, as shown on the unit wiring diagram.

The displayed variables are:

• Phase to phase voltage, only for three-phase units;

• Phase voltage (phase-neutral);

• Phase current;

• Neutral current only for three-phase units;

• Active phase power, only for three-phase units;

• Total active power;

• Active energy;

• Hour counts

INSTALLATION

Frame

Power Supply

Installation

Code

E1

400/3+N/50

EXTERNAL to the unit, supplied in kit

P183 / P184 (*)

E2

400/3+N/50

EXTERNAL to the unit, supplied in kit

P183 / P184 (*)

E3

400/3+N/50

EXTERNAL to the unit, supplied in kit

P183 / P184 (*)

E4

400/3+N/50

INTERNAL (on unit electrical panel)

P181 / P182 (*)

E5

400/3+N/50

INTERNAL (on unit electrical panel)

P181 / P182 (*)

E6

400/3+N/50

INTERNAL (on unit electrical panel)

P181 / P182 (*)

E7

400/3+N/50

INTERNAL (on unit electrical panel)

P181 / P182 (*)

E8

400/3+N/50

INTERNAL (on unit electrical panel)

P181 / P182 (*)

E9

400/3+N/50

INTERNAL (on unit electrical panel)

P183 / P184 (*)

(*) P182, P184 for units with optional (with electric heaters and/or humidifier)

INTERNAL INSTALLATION

The optional is installed within the electrical box downstream the main switch with door safety lock and includes:

• Network transducer;

• Current transformers, one for each power supply phase cable.

MOUNTING KIT

The optional is supplied in box for external installation to the machine with the dimensions showed in the figure below, and includes:

• Main switch with door lock safety;

• Fuse;

• Network transducer;

• Current transformers, one for each power supply phase cable;

• Terminals.

INTERNAL installation

EXTERNAL installation

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

39

MEHITS S.p.A.

DATA BOOK

HE

PF

T2

T1

M1

M3

Tin

HE

PF

T2

T1

M1

M3

Tin

OPTIONAL ACCESSORIES: P021 – 2-WAY BALL BY-PASS VALVE

The optional is available for main chilled water circuit only. 2-way motorized valve with 0÷10 VDC control actuator and emergency manual control for the third way (by-pass) of the hydraulic circuit.

The valve is in combination with the main 2-way water flow control valve. The optional accessory is factory installed and don’t modify the overall dimensions of the unit.

The coupling to the main 2-way control valve of a second modulating valve, connected in by-pass, allows to obtain the same control system of a 3-way mixing valve for plant with constant water flow. At the same time the appropriate sizing of these valves allows hydraulic balancing of the by-pass way.

This type of valve offers the following series of benefits:

• Equal percentage flow control.

• No peaks initial flow.

• Excellent stability control thanks to the integrated characterizing disc.

• Excellent characteristic in partialisation.

• Stability in control.

• Maintenance free.

• Self-cleaning.

CHARACTERISTICS OF THE 2-WAY BALL VALVE

• Closing seal with leakage rate in Class A (EN 12266-1)

• Maximum fluid pressure Ps=1600kPa

• Maximum closing pressure (Close-off) ∆Ps=1400kPa

The rotative actuator is controlled by a signal 0 … 10VDC from the microprocessor controller. The actuator is equipped with an emergency button for manual operation and is maintenance-free.

Air flow

Water Inlet / Outlet

Main circuit

Water Inlet / Outlet

Main circuit

UNDER Version

OVER Version

Air flow

LEGENDA M1 2-way modulating valve for

main coil M3 2-way modulating valve for by-

pass HE Main coil PF Plug Fan. T1 Air return temperature probe T2 Air supply temperature probe Tin Chilled water inlet temperature

probe

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

40

MEHITS S.p.A.

DATA BOOK

TECHNICAL DATA

VERSION (1)

U / O

MODEL

011 P1 S

014 P1 S

016 P1 S

020 P1 S

022 P1 S

026 P1 S

032 P1 S

SIZE E1

E2

E3

E4

2-WAY VALVE FOR BY-PASS

kv – Flow coefficient

m3/h

4,0

6,3

8,6

VERSION (1)

U / O

MODEL

037 P1 S

041 P1 S

045 P1 S

039 P2 D

048 P2 D

055 P2 D

062 P2 D

SIZE E4

E4

E5

E6

2-WAY VALVE FOR BY-PASS

kv – Flow coefficient

m3/h

8,6

16,0

VERSION (1)

U / O

U / O U U

MODEL

075 P2 D

082 P2 D

092 P2 D

102 P2 D

117 P4 D

146 P4 D

SIZE E7

E7

E8

E9

2-WAY VALVE FOR BY-PASS

kv – Flow coefficient

m3/h

16,0

25,0

1. U = Under, downflow / O = Over, upflow

IMPORTANT For further information, please refer to chapter “VALVE PRESSURE DROP CALCULATION AS FUNCTION OF WATER FLOW RATE”

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

41

MEHITS S.p.A.

DATA BOOK

OPTIONAL ACCESSORIES: A431 – ELECTRIC HEATERS

OPTIONAL ACCESSORIES: A432 – EXTRA POWER ELECTRIC HEATERS

A431 –ELECTRIC HEATERS

Electric heater consisting of finned aluminum elements, ensuring low surface temperature and deleting the air ionization problems. The optional is installed downstream the main cooling coil. In electric heaters with three working steps the activation is binary type.

Components:

• Electric heater in aluminium armoured elements with integral fins

• Electrical control

• Safety thermostat.

TECHNICAL DATA

VERSION (1)

U / O

MODEL

011 P1 S

014 P1 S

016 P1 S

020 P1 S

022 P1 S

026 P1 S

SIZE E1

E2

E3

THERMAL CAPACITY

kW

5,1

6,0

Absorbed current (OA)

A

7,4

8,7

First working step

kW

5,1

3,0

Second working step

kW

--

3,0+3,0

Third working step

kW

--

NET WEIGHT (2)

kg 4 4 4 7 7 7

VERSION (1)

U / O

MODEL

032 P1 S

037 P1 S

041 P1 S

045 P1 S

039 P2 D

048 P2 D

SIZE E4

E4

E5

THERMAL CAPACITY

kW

9,0

13,5

Absorbed current (OA)

A

13,0

19,5

First working step

kW

3,0

4,5

Second working step

kW

6,0

9,0

Third working step

kW

3,0+6,0

4,5+9,0

NET WEIGHT (2)

kg

9,5

10

VERSION (1)

U / O

MODEL

055 P2 D

062 P2 D

075 P2 D

082 P2 D

092 P2 D

102 P2 D

SIZE E6

E6

E7

E8

THERMAL CAPACITY

kW

13,5

18,0

Absorbed current (OA)

A

19,5

26,0

First working step

kW

4,5

Second working step

kW

9,0

13,5

Third working step

kW

4,5+9,0

4,5+13,5

NET WEIGHT (2)

kg

9,5

11

VERSION (1)

U U

MODEL

117 P4 D

146 P4 D

SIZE E9

E9

THERMAL CAPACITY

kW

18,0

Absorbed current (OA)

A

26,0

First working step

kW

4,5

Second working step

kW

13,5

Third working step

kW

4,5+13,5

NET WEIGHT (2)

kg

11

1. U = Under, downflow / O = Over, upflow

2. Value to be added to the weight of the standard unit.

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

42

MEHITS S.p.A.

DATA BOOK

A432 – EXTRA POWER ELECTRIC HEATERS

The optional is not available for sizes E1, E2. The components are the same of the standard accessory

TECHNICAL DATA

VERSION (1)

U / O

MODEL

011 P1 S

014 P1 S

016 P1 S

020 P1 S

022 P1 S

026 P1 S

SIZE E1

E2

E3

THERMAL CAPACITY

kW

--

9,0

Absorbed current (OA)

A

--

13,0

First working step

kW

--

4,5

Second working step

kW

--

4,5+4,5

Third working step

kW

--

NET WEIGHT (2)

kg

--

-- 7 7

7

VERSION (1)

U / O

MODEL

032 P1 S

037 P1 S

041 P1 S

045 P1 S

039 P2 D

048 P2 D

SIZE E4

E4

E5

THERMAL CAPACITY

kW

13,5

18,0

Absorbed current (OA)

A

13,0

26,0

First working step

kW

4,5

Second working step

kW

9,0

13,5

Third working step

kW

4,5+9,0

4,5+13,5

NET WEIGHT (2)

kg

9,5

12

VERSION (1)

U / O

MODEL

055 P2 D

062 P2 D

075 P2 D

082 P2 D

092 P2 D

102 P2 D

SIZE E6

E6

E7

E8

THERMAL CAPACITY

kW

18,0

27,0

Absorbed current (OA)

A

26,0

39,0

First working step

kW

4,5

9,0

Second working step

kW

13,5

18,0

Third working step

kW

4,5+13,5

9,0+18,0

NET WEIGHT (2)

kg

11,5

14,5

VERSION (1)

U U

MODEL

117 P4 D

146 P4 D

SIZE E9

E9

THERMAL CAPACITY

kW

27,0

Absorbed current (OA)

A

39,0

First working step

kW

9,0

Second working step

kW

18,0

Third working step

kW

9,0+18,0

NET WEIGHT (2)

kg

14,5

1. U = Under, downflow / O = Over, upflow

2. Value to be added to the weight of the standard unit.

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

43

MEHITS S.p.A.

DATA BOOK

OPTIONAL ACCESSORIES: 4301 – STEAM HUMIDIFIER 3KG/H

OPTIONAL ACCESSORIES: 4303 – STEAM HUMIDIFIER 8KG/H

OPTIONAL ACCESSORIES: 4305 – STEAM HUMIDIFIER 15KG/H

Modulating steam humidifier with immersed electrodes fitted with safety and running accessories The optional includes the control board. The optional requires mandatory accessory “P161 T/rH air intake sensor“. The optional is factory installed and requires only water filling connection.

Humidifier water charge and discharge pipes are not supplied.

It is recommended to install a filter and a shut-off valve on the pipe to the water inlet. This humidifier produces non-pressurized steam by electrodes immersed in the water inside the cylinder: they bring the electric phase in the water that works as an electrical resistance and overheats. The steam so produced is distributed with dedicated distributors and used for ambient humidification or for industrial processes.

CHARACTERISTICS OF THE SUPPLY WATER The quality of the used water influences the evaporation process, so the humidifier can be fed with not- treated water, only when potable and non-demineralised.

LIMIT VALUES

Min

Max

Hydrogen ions

pH 7

8,5

Specific conductivity at 20°C

σ

R, 20 °C

μS/cm

350

750

Total dissolved solids

TDS

mg/l

(1)

Dry residue at 180°C

R

180

mg/l

(1)

Total hardness

TH

mg/l CaCO3

100 (2)

400

Temporary hardness

mg/l CaCO3

60 (3)

300

Iron + Manganese

mg/l Fe + Mn

0

0,2

Chlorides

ppm Cl 0 30

Silica mg/l SiO2 0 20

Residual chlorine

mg/l Cl- 0 0,2

Calcium sulphate

mg/l CaSO4

0

100

Metallic impurities

mg/l 0 0

Solvents, diluents, soaps, lubricants

mg/l 0 0

(1) Values depending on specific conductivity; in general: TDS ≅ 0,93 * σ

R, 20 °C; R180

≅ 0,65 * σR

(2) Not lower than 200% of the chloride content in mg/l di Cl(3) Not lower than 300% of the chloride content in mg/l di Cl-

WARNING:

• Use only with drinking water.

• There is no reliable relationship between hardness and water conductivity

• Do not treat water with softeners! This could cause corrosion of the electrodes or the

formation of foam, leading to potential operating problems or failures.

• Do not add disinfectants or corrosion inhibiters to water, as these substances are

potentially irritant.

• Is absolutely forbidden to use well water, industrial water or water drawn from cooling

circuits; in general, avoid using potentially contaminated water, either from a chemical or bacteriological point of view.

TECHNICAL DATA

VERSION (1)

U / O

MODEL

011 P1 S

014 P1 S

016 P1 S

020 P1 S

022 P1 S

026 P1 S

SIZE E1

E2

E3

STEAM PRODUCTION

kg/h

3,0

Power input

kW

2,3

Absorbed current (OA)

A

3,2

Max absorbed current (FLA)

A

4,5

Water content

l

3,9

Max water supply pressure

Bar

1÷8

NET WEIGHT (2)

kg 4 5 5 6 6 6

HYDRAULIC CONNECTION

WATER INLET - ISO 228/1 – G M

Ø

3/4"

WATER OUTLET - external diameter

Ø mm

19

1. U = Under, downflow / O = Over, upflow

2. Value to be added to the weight of the standard unit. Does not include the weight of the water content.

Humidifier control board

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

44

MEHITS S.p.A.

DATA BOOK

TECHNICAL DATA

VERSION (1)

U / O

MODEL

032 P1 S

037 P1 S

041 P1 S

045 P1 S

039 P2 D

048 P2 D

SIZE E4

E4

E5

STEAM PRODUCTION

kg/h

8,0

Power input

kW

6,0

Absorbed current (OA)

A

8,7

Max absorbed current (FLA)

A

12,4

Water content

l

6,0

Max water supply pressure

Bar

1÷8

NET WEIGHT (2)

kg

10

12

HYDRAULIC CONNECTION

WATER INLET - ISO 228/1 – G M

Ø

3/4"

WATER OUTLET - external diameter

Ø mm

19

VERSION (1)

U / O

MODEL

055 P2 D

062 P2 D

075 P2 D

082 P2 D

092 P2 D

102 P2 D

SIZE E6

E6

E7

E8

STEAM PRODUCTION

kg/h

8,0

Power input

kW

6,0

Absorbed current (OA)

A

8,7

Max absorbed current (FLA)

A

12,4

Water content

l

6,0

Max water supply pressure

Bar

1÷8

NET WEIGHT (2)

kg

14

HYDRAULIC CONNECTION

WATER INLET - ISO 228/1 – G M

Ø

3/4"

WATER OUTLET - external diameter

Ø mm

19

VERSION (1)

U U

MODEL

117 P4 D

146 P4 D

SIZE E9

E9

STEAM PRODUCTION

kg/h

8,0

Power input

kW

6,0

Absorbed current (OA)

A

8,7

Max absorbed current (FLA)

A

12,4

Water content

l

6,0

Max water supply pressure

Bar

1÷8

NET WEIGHT (2)

kg

14

HYDRAULIC CONNECTION

WATER INLET - ISO 228/1 – G M

Ø

3/4"

WATER OUTLET - external diameter

Ø mm

19

1. U = Under, downflow / O = Over, upflow

2. Value to be added to the weight of the standard unit. Does not include the weight of the water content.

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

45

MEHITS S.p.A.

DATA BOOK

EXTRA POWER HUMIDIFIERS

The optional is not available for size E1, E2, E3. The components are the same of the standard accessory

TECHNICAL DATA

VERSION (1)

U / O

MODEL

011 P1 S

014 P1 S

016 P1 S

020 P1 S

022 P1 S

026 P1 S

SIZE E1

E2

E3

STEAM PRODUCTION

kg/h

--

Power input

kW

--

Absorbed current (OA)

A

--

Max absorbed current (FLA)

A

--

Water content

l

--

Max water supply pressure

Bar

--

NET WEIGHT (2)

kg

--

HYDRAULIC CONNECTION

WATER INLET - ISO 228/1 – G M

Ø

--

WATER OUTLET - external diameter

Ø mm

--

VERSION (1)

U / O

MODEL

032 P1 S

037 P1 S

041 P1 S

045 P1 S

039 P2 D

048 P2 D

SIZE E4

E4

E5

STEAM PRODUCTION

kg/h

15

Power input

kW

11,3

Absorbed current (OA)

A

16,2

Max absorbed current (FLA)

A

23

Water content

l

10,3

Max water supply pressure

Bar

1÷8

NET WEIGHT (2)

kg

16

HYDRAULIC CONNECTION

WATER INLET - ISO 228/1 – G M

Ø

3/4"

WATER OUTLET - external diameter

Ø mm

19

VERSION (1)

U / O

MODEL

055 P2 D

062 P2 D

075 P2 D

082 P2 D

092 P2 D

102 P2 D

SIZE E6

E6

E7

E8

STEAM PRODUCTION

kg/h

15

Power input

kW

11,3

Absorbed current (OA)

A

16,2

Max absorbed current (FLA)

A

23

Water content

l

10,3

Max water supply pressure

Bar

1÷8

NET WEIGHT (2)

kg

16

HYDRAULIC CONNECTION

WATER INLET - ISO 228/1 – G M

Ø

3/4"

WATER OUTLET - external diameter

Ø mm

19

1. U = Under, downflow / O = Over, upflow

2. Value to be added to the weight of the standard unit. Does not include the weight of the water content.

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

46

MEHITS S.p.A.

DATA BOOK

TECHNICAL DATA

VERSION (1)

U U

MODEL

117 P4 D

146 P4 D

SIZE E9

E9

STEAM PRODUCTION

kg/h

15

Power input

kW

11,3

Absorbed current (OA)

A

16,2

Max absorbed current (FLA)

A

23

Water content

l

10,3

Max water supply pressure

Bar

1÷8

NET WEIGHT (2)

kg

16

HYDRAULIC CONNECTION

WATER INLET - ISO 228/1 – G M

Ø

3/4"

WATER OUTLET - external diameter

Ø mm

19

1. U = Under, downflow / O = Over, upflow

2. Value to be added to the weight of the standard unit. Does not include the weight of the water content.

OPTIONAL ACCESSORIES : P051 – DEHUMIDIFICATION FUNCTION

The optional requires mandatory accessory “P161 T/rH air intake sensor“.

Components:

• T / rH air intake sensor.

• Electronic control system of the dew point temperature for the combined intervention of

cooling capacity and air flow.

OPTIONAL ACCESSORIES: P161 - T/RH AIR INTAKE SENSOR

OPTIONAL ACCESSORIES: P071 - REMOTE T/RH PROBE

P161: T/RH AIR INTAKE SENSOR

The accessory replaces the temperature sensor installed on the air intake in the unit and allows the displaying of the relative humidity room value The sensor is mandatorily required with following option:

• 4301 / 4303 / 4305 Humidifier;

• P161 Dehumidification function;

• P034 Intake free-cooling plenum.

P071: REMOTE T/RH PROBE

The accessory is added to the standard temperature sensor or to the temperature / humidity sensor (optional) on the machine air intake. For indoor installation in a specific point of the room to be conditioned.

OPTIONAL ACCESSORIES: 4666 – EXTERNAL AIR PROBE

The probe must be installed protected against atmospheric agent and allows the displaying of the external air temperature. The sensor is mandatorily required with following option:

• P034 Intake free-cooling plenum.

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

47

MEHITS S.p.A.

DATA BOOK

OPTIONAL ACCESSORIES: P111 – DUAL POWER SUPPLY

OPTIONAL ACCESSORIES: P112 – DUAL POWER SUPPLY + OPTIONAL

OPTIONAL ACCESSORIES: P113 – KIT DUAL POWER SUPPLY

OPTIONAL ACCESSORIES: P114 – KIT DUAL POWER SUPPLY + OPTIONAL

The motorised changeover switches automatically manage changeover under load between two threephase power supplies, or manually for emergency operations. These devices are suitable for low voltage systems with interruption of the supply to the load during transfer. The model supplied in the automatic version checks the source and switches over automatically, based on configurable parameters.

OPEN TRANSITION TYPE TRANSFER SWITCH WITH A MINIMUM INTERRUPTION OF THE SUPPLY DURING TRANSFER.

To maintain the microprocessor powered and avoid its restarts it is suggested the “P091 Backup module controller” optional accessory. The back-up module guarantees the microprocessor

power supply for a few minutes, in case of supply voltage failure.

The remote condenser must be powered by the automatic transfer switch.

It is suggested the optional “P191 power supply for condenser” from the indoor machine electrical board. The optional includes magnetothermic switches for condenser fans.

INSTALLATION

Frame

Power Supply

Installation

Code

E1

400/3+N/50

EXTERNAL to the unit, supplied in kit

P113, P114 (*)

E2

400/3+N/50

EXTERNAL to the unit, supplied in kit

P113, P114 (*)

E3

400/3+N/50

EXTERNAL to the unit, supplied in kit

P113, P114 (*)

E4

400/3+N/50

EXTERNAL to the unit, supplied in kit

P113, P114 (*)

E5

400/3+N/50

INTERNAL (on unit electrical panel)

P111, P112 (*)

E6

400/3+N/50

INTERNAL (on unit electrical panel)

P111, P112 (*)

E7

400/3+N/50

INTERNAL (on unit electrical panel)

P111, P112 (*)

E8

400/3+N/50

INTERNAL (on unit electrical panel)

P111, P112 (*)

E9

400/3+N/50

INTERNAL (on unit electrical panel)

P111, P112 (*)

(*) P112, P114 for units with optional (with electric heaters and/or humidifier)

MOUNTING KIT

For EXTERNAL installation, the optional accessory is supplied in special box with IP 3X ingress protection, with the dimensions shown in the figure below.

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

48

MEHITS S.p.A.

DATA BOOK

OPTIONAL ACCESSORIES: A381 - DRAIN PUMP

A plastic case contains the vertical type pump, the water tank with float plus safety switch and hydraulic and electric connection. Together the pump 10 linear meters anti-crushing plastic discharge spiral tube is supplied The optional must be installed as shown in the documentation delivered together with the unit. Wiring includes power supply and an alarm, displayed on microprocessor, that includes motor pump thermal protection and tank overflow. The condensate discharge pump operation is fully automatic.

WARNING For all the machines the optional accessory is supplied in mounting kit.

TECHNICAL DATA Power supply: 230V~ 50Hz Electrical data: 70W – 0,67A Maximum water flow: 500 l/h Maximum delivery height: 5.0 m Sound level: 45dBA a 1 m Maximum water temperature: 70°C Water acidity: pH>2.5 Tray volume: 2.0 l Protection IP 20

Total length of discharge

pipes (Ø 10 mm internal)

Discharge

head

5m

10m

20m

30m

1m

380

300

240

190

2m

310

260

200

150

3m

240

200

145

110

4m

150

130

80

60

5m

30

20 0 0

CONDENSATE DISCHARGE PUMP

(Dimensions in millimetres)

Water flow

Discharge head

OPERATING DATA

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

49

MEHITS S.p.A.

DATA BOOK

OPTIONAL ACCESSORIES: P084 – AIR FILTER ePM10 50%

The ePM

10

50% air filters (according to ISO EN 16890), replace the standard one. The filters generate a pressure drops higher than the standard ones. The filters are made of glass micro-fibre and are not regenerable.

VERSION (1)

U / O

MODEL 011 P1 S

014 P1 S

016 P1 S

020 P1 S

022 P1 S

026 P1 S

SIZE E1

E2

E3

Additional pressure drops (2)

Pa

53

65

70

54

62

68

VERSION (1)

U / O

MODEL 032 P1 S

037 P1 S

041 P1 S

045 P1 S

039 P2 D

048 P2 D

SIZE E4

E4

E5

Additional pressure drops (2)

Pa

30

39

45

23

35

VERSION (1)

U / O

MODEL 055 P2 D

062 P2 D

075 P2 D

082 P2 D

092 P2 D

102 P2 D

SIZE E6

E6

E7

E8

Additional pressure drops (2)

Pa

41

44

72

69

VERSION (1)

U

MODEL 117 P4 D

146 P4 D

SIZE E9

E9

Additional pressure drops (2)

Pa

94

1. U = Under, downflow / O = Over, upflow

2. Additional pressure drops referred to nominal air flow and clean filter.

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

50

MEHITS S.p.A.

DATA BOOK

OPTIONAL ACCESSORIES: A531 – ON-OFF DAMPER

Non-return air damper with frame driven by electric servomotor. Accessory installed on units air delivery and it can be matched to plenums and support frame.

The accessory requires mandatory accessory “9973 Wooden cage packing”.

FRAMEWORK

• Frame in galvanized steel sheet with protective surfaces treatment in compliance with UNI

ISO 9227/ASTMB117 and ISO 7253, and painted with epoxy powders. Colour RAL 9005;

• Opposed blade dampers in galvanized steel sheet.

• Actuator for damper control.

• Terminals for electric connection to the unit.

VERSION (1)

U / O

U

SIZE

E1

E2

E3

E4

E5

E6

E7

E8

E9

A

mm

650

785

1085

1305

1630

1873

2175

2499

2899

B

mm

650

750

905

C

mm

300

450

750

900

1250

1500

1750

2000

2300

D

mm

510

610

710

E

mm

231

216

142

204

250,5

226,5

238,5

288,5

F

mm

73

202

115

61,5

137,5

199,5

249,5

G

mm

46

61

H

mm

170

Weight (2)

kg

20

23

30

40

50

58

65

75

90

1. U = Under, downflow / O = Over, upflow

2. Add this value to the total unit weight

H

F E G

C

22

A

B

D

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

51

MEHITS S.p.A.

DATA BOOK

INSTALLATION EXAMPLE

WORKING LOGIC The damper opens at supply fans activation to allow air flow. When the fans stop for failure or stop command, the damper closes, preventing air flow into the unit.

Damper

A531: OVER

A531: UNDER

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

52

MEHITS S.p.A.

DATA BOOK

OPTIONAL ACCESSORIES: P011 - EMPTY PLENUM OPTIONAL ACCESSORIES: P012 - EMPTY PLENUM CL.A1 OPTIONAL ACCESSORIES: P031 - EMPTY INTAKE PLENUM OPTIONAL ACCESSORIES: P032 - EMPTY INTAKE PLENUM CL.A1 OPTIONAL ACCESSORIES: P013 - PLENUM + 3 GRILLES OPTIONAL ACCESSORIES: P014 - PLENUM + 3 GRILLES CL.A1 OPTIONAL ACCESSORIES: P015 - SILENCED PLENUM OPTIONAL ACCESSORIES: P016 - SILENCED PLENUM + 1 GRILLE OPTIONAL ACCESSORIES: P017 - PLENUM + FILTER EPM2.5 50% OPTIONAL ACCESSORIES: P018 - PLENUM + FILTER EPM1 50% OPTIONAL ACCESSORIES: P019 - PLENUM + FILTER EPM1 85%

The optional is supplied separately and the installation on the unit is at Customer care. The plenums have same technical characteristics and base dimensions of the machine cabinet.

It is possible to install only a single plenum to ensure stability to the unit.

FRAMEWORK

• Frame in aluminium extrusion, painted with epoxy powders. Colour RAL 9005;

• Panels in galvanized steel sheet with protective surfaces treatment in compliance with UNI

ISO 9227/ASTMB117 and ISO 7253, and painted with epoxy powders. Colour RAL 9005;

• Panels insulated with polyurethane foam and seals to ensure air tight.

• Panels fixed with screws.

• Removable panels.

• Set of fixing elements to fasten the plenum to the unit.

WARNING In UNDER version units the piping is inside the machine. The air delivery plenums sometime don’t allow the extension of the pipes downwards. In special cases, to keep the connections inside the machine, foresee a plenum 200mm higher than the standard one.

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

53

MEHITS S.p.A.

DATA BOOK

P011 / P012 – P031 / P032: EMPTY PLENUM

The plenum is void and can be used to rise the intake/delivery air inlet/outlet. Remove the frontal panels for inspection.

Also available with fire reaction in class “0” or “A1” (EN 13501-1). The optional accessories “P031 Empty intake plenum, for OVER version” and “P032 Empty intake plenum CL.A1, for OVER version” require mandatory accessory “P122 Bottom air intake+blind panels, for OVER version only”

VERSION (1)

U / O

U

SIZE E1

E2

E3

E4

E5

E6

E7

E8

E9

A

mm

490

510

Weight (2)

kg

20

21

20

30

40

45

50

60

70

Weight CL.0 or A1 (EN 13501-1) (2)

kg

25

27

39

50

56

62

74

85

1. U = Under, downflow / O = Over, upflow

2. Add this value to the total unit weight

P013 / P014: PLENUM + 3 GRILLES

The plenum must be installed on air delivery. The plenum allows the air distribution directly into the room. The plenum is supplied with air distribution grilles with double row adjustable grilles on front and lateral side. Also available with fire reaction in class “0” or “A1” (EN 13501-1).

VERSION (1)

U / O

U

SIZE E1

E2

E3

E4

E5

E6

E7

E8

E9

A

mm

490

510

Weight (2)

kg

21

23

30

45

50

65

75

90

100

Weight CL.0 or A1 (EN 13501-1) (2)

kg

25

28

37

54

61

77

89

106

118

1. U = Under, downflow / O = Over, upflow

2. Add this value to the total unit weight

P013 / P014 OVER

P013 / P014 UNDER P011 / P012 OVER

P011 / P012 UNDER

P031 / P032 OVER

P031 / P032 UNDER

P122 Bottom air intake+blind

panels

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

54

MEHITS S.p.A.

DATA BOOK

P015: SILENCED PLENUM

The plenum must be installed on air delivery. The plenum is fitted with noise absorption partitions to reduce the noise emission. Remove the frontal panels for inspection.

VERSION (1)

U / O

U

SIZE E1

E2

E3

E4

E5

E6

E7

E8

E9

A

mm

490

510

Weight (2)

kg

25

27

30

45

50

65

80

90

100

1. U = Under, downflow / O = Over, upflow

2. Add this value to the total unit weight

ACOUSTIC DATA

VERSION (1)

U / O

MODEL

011 P1 S

014 P1 S

016 P1 S

020 P1 S

022 P1 S

026 P1 S

SIZE E1

E2

E3

SOUND LEVEL ISO 3744 (2)

On air delivery, Under

dB(A)

60,4

66,7

67,8

66,4

67,9

68,9

On air intake, Under

dB(A)

56,1

57,4

58,5

57,3

59,2

59,5

On front side, Under

dB(A)

46,9

48

49,1

47,9

49,9

50,1

On air delivery, Over

dB(A)

60,4

66,7

67,8

66,4

67,9

68,9

On air intake, Over (3)

dB(A)

51,7

54,1

55,5

55,4

58,6

57,0

On front side, Over (4)

dB(A)

42,0

47,6

48,6

47,0

48,9

49,4

Air flow (5)

m3/h

2800

4000

4200

5700

6100

6400

VERSION (1)

U / O

MODEL

032 P1 S

037 P1 S

041 P1 S

045 P1 S

039 P2 D

048 P2 D

SIZE E4

E4

E5

SOUND LEVEL ISO 3744 (2)

On air delivery, Under

dB(A)

73,8

76,8

74,6

77,0

77,1

On air intake, Under

dB(A)

64,1

67,0

66,4

67,2

68,9

On front side, Under

dB(A)

54,6

57,5

57,0

57,7

59,4

On air delivery, Over

dB(A)

73,8

76,8

74,6

77,0

77,1

On air intake, Over (3)

dB(A)

60,5

62,6

62,4

62,7

64,3

On front side, Over (4)

dB(A)

54,3

57,3

56,7

57,5

59,3

Air flow (5)

m3/h

8700

10000

10800

10000

12000

1. U = Under, downflow / O = Over, upflow

2. Noise pressure level at 1 meter in free field – ISO 3744

3. Air intake from the front

4. Air intake from the bottom

5. Nominal air flow with noise absorption partitions plenum installation and external static pressure 20 Pa.

P015 UNDER

P015 OVER

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

55

MEHITS S.p.A.

DATA BOOK

ACOUSTIC DATA

VERSION (1)

U / O

MODEL

055 P2 D

062 P2 D

075 P2 D

082 P2 D

092 P2 D

102 P2 D

SIZE E6

E6

E7

E8

SOUND LEVEL ISO 3744 (2)

On air delivery, Under

dB(A)

73,7

74,6

75,9

78,1

On air intake, Under

dB(A)

64,2

65,1

67,7

69,9

On front side, Under

dB(A)

54,7

55,7

58,4

60,6

On air delivery, Over

dB(A)

73,7

74,6

75,9

78,1

On air intake, Over (3)

dB(A)

60,9

62,3

63,9

66,1

On front side, Over (4)

dB(A)

54,2

55,1

58,0

60,3

Air flow (5)

m3/h

15000

15600

20000

22000

VERSION (1)

U U

MODEL

117 P4 D

146 P4 D

SIZE E9

E9

SOUND LEVEL ISO 3744 (2)

On air delivery, Under

dB(A)

79,1

On air intake, Under

dB(A)

70,9

On front side, Under

dB(A)

61,4

On air delivery, Over

dB(A) - -

On air intake, Over (3)

dB(A) - -

On front side, Over (4)

dB(A) - -

Air flow (5)

m3/h

32000

1. U = Under, downflow / O = Over, upflow

2. Noise pressure level at 1 meter in free field – ISO 3744

3. Air intake from the front

4. Air intake from the bottom

5. Nominal air flow with noise absorption partitions plenum installation and external static pressure 20 Pa.

P016: SILENCED PLENUM + 1 GRILLE

The plenum must be installed on air delivery. The plenum allows the frontal air distribution directly into the room and a noise reduction of the air delivery. The plenum is supplied with air distribution grille with double row adjustable grilles on front side and noise absorption partitions,

VERSION (1)

U / O

U

SIZE E1

E2

E3

E4

E5

E6

E7

E8

E9

A

mm

490

510

Weight (2)

kg

30

37

67

72

78

88

110

130

1. U = Under, downflow / O = Over, upflow

2. Add this value to the total unit weight

P016 OVER

P016 UNDER

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

56

MEHITS S.p.A.

DATA BOOK

ACOUSTIC DATA

VERSION (1)

U / O

MODEL

011 P1 S

014 P1 S

016 P1 S

020 P1 S

022 P1 S

026 P1 S

SIZE E1

E2

E3

SOUND LEVEL ISO 3744 (2)

On air delivery, Under

dB(A)

60,0

67,3

68,3

66,3

67,7

68,7

On air intake, Under

dB(A)

55,8

58,1

59,2

57,7

59,6

60,0

On front side, Under

dB(A)

46,6

48,7

49,8

48,3

50,3

50,5

On air delivery, Over

dB(A)

60,0

67,3

68,3

66,3

67,7

68,7

On air intake, Over (3)

dB(A)

51,6

53,8

55,2

55,3

58,5

56,9

On front side, Over (4)

dB(A)

41,8

47,1

48,1

46,7

48,7

49,0

ADDITIONAL PRESSURE DROPS (5)

Pa

77

79

87

63

72

79

AIR FLOW

m3/h

2700

4000

4200

5700

6100

6400

VERSION (1)

U / O

MODEL

032 P1 S

037 P1 S

041 P1 S

045 P1 S

039 P2 D

048 P2 D

SIZE E4

E4

E5

SOUND LEVEL ISO 3744 (2)

On air delivery, Under

dB(A)

73,1

76,1

73,9

76,2

76,4

On air intake, Under

dB(A)

64,1

67,0

66,4

67,1

68,7

On front side, Under

dB(A)

54,6

57,4

57,0

57,6

59,3

On air delivery, Over

dB(A)

73,1

76,1

73,9

76,2

76,4

On air intake, Over (3)

dB(A)

60,5

62,6

62,4

62,1

62,8

64,4

On front side, Over (4)

dB(A)

54,3

57,3

56,8

57,6

59,4

ADDITIONAL PRESSURE DROPS (5)

Pa

69

92

106

57

85

AIR FLOW

m3/h

8700

10000

10800

10000

12000

VERSION (1)

U / O

MODEL

055 P2 D

062 P2 D

075 P2 D

082 P2 D

092 P2 D

102 P2 D

SIZE E6

E6

E7

E8

SOUND LEVEL ISO 3744 (2)

On air delivery, Under

dB(A)

73,3

74,1

75,3

77,3

On air intake, Under

dB(A)

64,4

65,3

67,8

67,9

69,8

69,9

On front side, Under

dB(A)

54,9

55,9

58,4

58,5

60,4

60,5

On air delivery, Over

dB(A)

73,3

74,1

75,3

77,3

On air intake, Over (3)

dB(A)

60,8

62,2

63,9

64,3

66,2

66,5

On front side, Over (4)

dB(A)

54,1

55,0

58,1

60,4

ADDITIONAL PRESSURE DROPS (5)

Pa

100

108

133

121

AIR FLOW

m3/h

15000

15600

20000

22000

VERSION (1)

U U

MODEL

117 P4 D

146 P4 D

SIZE E9

E9

SOUND LEVEL ISO 3744 (2)

On air delivery, Under

dB(A)

78,5

On air intake, Under

dB(A)

70,9

On front side, Under

dB(A)

61,5

On air delivery, Over

dB(A)

--

On air intake, Over (3)

dB(A)

--

On front side, Over (4)

dB(A)

--

ADDITIONAL PRESSURE DROPS (5)

Pa

191

AIR FLOW

m3/h

32000

1. U = Under, downflow / O = Over, upflow

2. Noise pressure level at 1 meter in free field – ISO 3744

3. Air intake from the front

4. Air intake from the bottom

5. Value to be subtracted from the nominal external static pressure of the unit

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

57

MEHITS S.p.A.

DATA BOOK

P017 / P018 / P019: SUPPLY PLENUM + FILTER

The plenum must be installed on air delivery. The optional is not compatible with “P084 Air filter ePM10 50%”. The plenum is fitted with high efficiency rigid bag filters. Filters are made of glass micro fibre and are not regenerable. Remove the frontal panels for filters replacement.

VERSION (1)

U / O

U

SIZE E1

E2

E3

E4

E5

E6

E7

E8

E9

A

mm

490

510

Weight (2)

kg

26

27

30

45

55

65

80

90

100

1. U = Under, downflow / O = Over, upflow

2. Add this value to the total unit weight

VERSION (1)

U / O

MODEL

011 P1 S

014 P1 S

016 P1 S

020 P1 S

022 P1 S

026 P1 S

SIZE E1

E2

E3

PRESSURE DROPS (2)

Filters ePM

2.5

50%

Pa

85

89

97

82

94

102

Filters ePM1 50%

Pa

98

129

138

120

134

145

Filters ePM1 85%

Pa

115

151

165

141

158

173

VERSION (1)

U / O

MODEL

032 P1 S

037 P1 S

041 P1 S

045 P1 S

039 P2 D

048 P2 D

SIZE E4

E4

E5

PRESSURE DROPS (2)

Filters ePM

2.5

50%

Pa

60

80

93

55

82

Filters ePM1 50%

Pa

94

118

133

88

121

Filters ePM1 85%

Pa

110

139

158

103

142

1. U = Under, downflow / O = Over, upflow

2. Data referred to the nominal air flow and clean filters. Value to be subtracted from the nominal external static pressure of the unit.

P017 / P018 / P019 OVER

P017 / P018 / P019 UNDER

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

58

MEHITS S.p.A.

DATA BOOK

VERSION (1)

U / O

MODEL

055 P2 D

062 P2 D

075 P2 D

082 P2 D

092 P2 D

102 P2 D

SIZE E6

E6

E7

E8

PRESSURE DROPS (2)

Filters ePM

2.5

50%

Pa

104

112

111

117

Filters ePM1 50%

Pa

147

158

157

139

Filters ePM1 85%

Pa

175

187

186

164

VERSION (1)

U U

MODEL

117 P4 D

146 P4 D

SIZE E9

E9

PRESSURE DROPS (2)

Filters ePM

2.5

50%

Pa

192

Filters ePM1 50%

Pa

230

231

Filters ePM1 85%

Pa

275

1. U = Under, downflow / O = Over, upflow

2. Data referred to the nominal air flow and clean filters. Value to be subtracted from the nominal external static pressure of the unit.

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

59

MEHITS S.p.A.

DATA BOOK

OPTIONAL ACCESSORIES: P034 – INTAKE FREE-COOLING PLENUM

The optional is supplied separately and the installation on the unit is at Customer care.

The optional requires mandatory accessories “P161 T/rH air intake sensor“, “4666 External air probe”, “A812 Free-cooling direct control” and “P122 Bottom air intake+blind panels, for OVER version only”.

The plenums have same technical characteristics and base dimensions of the machine cabinet. The optional allow to obtain free-cooling by direct ambient air intake into the room. The dampers are proportionally managed by the microprocessor control, that regulates the quantity of the ambient air to put in the room per the set-point.

COMPONENTS

• Frame in aluminium extrusion, painted with epoxy powders. Colour RAL 9005;

• Panels in galvanized steel sheet with protective surfaces treatment in compliance with UNI

ISO 9227/ASTMB117 and ISO 7253, and painted with epoxy powders. Colour RAL 9005;

• Panels insulated with polyurethane foam and seals to ensure air tight.

• Removable panels with screws.

• Opposed blade dampers in galvanized steel sheet and safety grille for ambient air and room

air suction.

• Actuator for each damper.

• Terminals for electric connection to the unit.

• Set of fixing elements to fasten the plenum to the unit.

• T / rH air intake sensor. The sensor must be moved outside the air conditioners for a proper

read of the room temperature value.

• External air probe. The sensor must be installed in the outdoor air suction duct or anyway

protected against atmospherics agent.

• Free contact for free-cooling operating status monitoring.

• Terminals on indoor unit for:

o 24 Vac power supply for the overpressure damper servomotor o 0-10Vdc control signal for the servomotor

INSTALLATION EXAMPLE

Ducting for ambient air suction are at Customer care. A rain cover with grille on ambient air intake is recommended.

P034 UNDER

P034 OVER

Inspection panels for air filters extraction

P122 Bottom air intake+blind panels

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

60

MEHITS S.p.A.

DATA BOOK

OVER VERSION

VERSION (1)

O O O O O O O O

O

SIZE E1

E2

E3

E4

E5

E6

E7

E8

E9

A

mm

650

785

1085

1305

1630

1873

2175

2499

--

B

mm

490

630

--

C

mm

650

750

905

--

D

mm

30

40

--

E

mm

430

550

--

F

mm

590

725

1025

1035

1335

1664

1965

2220

--

G

mm

--

135

147,5

209

210

279

--

Weight (2)

kg

24

27

35

53

61

78

90

110

--

1. U = Under, downflow / O = Over, upflow

2. Add this value to the total unit weight

SIZE E1 / E2 / E3

SIZE E4 / E5

SIZE E6 / E7 / E8

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

61

MEHITS S.p.A.

DATA BOOK

UNDER VERSION

VERSION (1)

U U U U U U U U

U

SIZE E1

E2

E3

E4

E5

E6

E7

E8

E9

A

mm

650

785

1085

1305

1630

1873

2175

2499

2899

B

mm

490

630

C

mm

650

750

905

D

mm

30

40

E

mm

430

550

F

mm

590

725

1025

1035

1335

1664

1965

2220

2670

G

mm

--

135

147,5

209

210

279

229

H

mm

--

275

Weight (2)

kg

24

27

35

53

61

78

90

110

130

1. U = Under, downflow / O = Over, upflow

2. Add this value to the total unit weight

SIZE E1 / E2 / E3

SIZE E4 / E5

SIZE E6 / E7 / E8 / E9

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

62

MEHITS S.p.A.

DATA BOOK

WARNING IT IS COMPULSORY TO INSTALL INTO THE ROOM AN APPROPRIATELY SIZED OVERPRESSURE DAMPER TO ALLOW THE ROOM AIR EXHAUSTION DURING FREE-COOLING WORKING MODE

OVERPRESSURE DAMPER – Not supplied

During free-cooling operation, the air conditioner supplies ambient air directly into the room, this causes an increase in air pressure inside the room. The overpressure damper avoids the increase in pressure in the room. The damper must be installed at the highest point of the room to expel excess hot air to the outside. Install the damper if possible in opposite position to air conditioner.

Air exhaustion must be protected with a rain cover and a grille (at Customer care).

Overpressure damper (not supplied)

Rain cover with grille (not supplied

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

63

MEHITS S.p.A.

DATA BOOK

OPTIONAL ACCESSORIES: P041 – SUPPORT FRAME H 255-350MM OPTIONAL ACCESSORIES: P042 – SUPPORT FRAME H 355-450MM OPTIONAL ACCESSORIES: P043 – SUPPORT FRAME H 400-510MM

The accessory is supplied as an assembly kit. It is not possible to match the unit floor stand with plenum installed under the machine. The floor stand is available in 3 different heights.

SIZE E1

E2

E3

E4

E5

E6

E7

E8

E9

A

mm

650

785

1085

1305

1630

1873

2175

2499

2899

B

mm

650

750

905

C

mm

524

659

959

955

1280

761,5

912,5

1074,5

1274,5

D

mm

691

791

945

MODEL P041 - Hmax350

P042 - Hmax450

P043 - Hmax510

H min height

mm

255

355

400

H max height

mm

350

450

510

H

B

63

82

C A D D B

H

82

H

B

D

82

175

175 A C

C

175

175 A 175

175 A C

SIZE E6 – E7 – E8 – E9

SIZE E4 – E5

SIZE E1 - E2 – E3

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

64

MEHITS S.p.A.

DATA BOOK

OPTIONAL ACCESSORIES: 1511 – SOFT STARTER

The optional is not available for size E1, E2. Compressor motors soft-starter system. The system is contained in the electrical box. Its function is to reduce the starting current of the motor with a monitored start.

The reduction of the starting current produced by soft starter optional accessory reduces the stress on the power line and on the compressors contributing to increase the components lifetime.

VERSION (1)

U / O

MODEL

011 P1 S

014 P1 S

016 P1 S

020 P1 S

022 P1 S

026 P1 S

SIZE E1

E2

E3

ON/OFF COMPRESSORS

- - - scroll

scroll

Compressors number

# - - - 1 1 1

Total starting current [LRA]

A - - - 64

75

101

WITH SOFT STARTER

Total starting current [LRA]

A - - - 37

47

51

VERSION (1)

U / O

MODEL

032 P1 S

037 P1 S

041 P1 S

045 P1 S

039 P2 D

048 P2 D

SIZE E4

E4

E5

ON/OFF COMPRESSORS

scroll

Compressors number

# 1 1 1 1 2 2

Total starting current [LRA]

A

128

139

118

140

76

90

WITH SOFT STARTER

Total starting current [LRA]

A

57

67

79

97

50

63

VERSION (1)

U / O

MODEL

055 P2 D

062 P2 D

075 P2 D

082 P2 D

092 P2 D

102 P2 D

SIZE E6

E6

E7

E8

ON/OFF COMPRESSORS

scroll

Compressors number

#

2

2 2 2 2 2

Total starting current [LRA]

A

117

146

161

143

171

208

WITH SOFT STARTER

Total starting current [LRA]

A

69

78

94

107

131

143

VERSION (1)

U U

MODEL

117 P4 D

146 P4 D

SIZE E9

E9

ON/OFF COMPRESSORS

Compressors number

# 4 4

Total starting current [LRA]

A

183

193

WITH SOFT STARTER

Total starting current [LRA]

A

131

150

1. U = Under, downflow / O = Over, upflow

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

65

MEHITS S.p.A.

DATA BOOK

OPTIONAL ACCESSORIES: A272 – CL.0 or A1 (EN13501-1) INSULATION

The optional is designed TO SUPPLY THE PANELING ONLY WITH FIRE REACTION IN CLASS “0” OR “A1 (EN 13501-1)”; furthermore, allows a noise insulation of the panels of the air conditioners.

The pressure level reduction of the unit is about 2 dB(A). The reduction refers ONLY to the sound level radiated from the unit or in front of the unit. The noise level data on return and delivery air do not undergo reductions. The accessory includes:

• External part as standard panel.

• Internal part in galvanized steel sheet.

• The inside noise insulation with special soundproof material.

REACTION TO FIRE CLASSIFICATION On Italian territory, the classification is per the D.M. of June 26, 1984 and subsequent amendments, providing for a sort in "Classes" from 0 (non-combustible material) to 5 (extremely flammable material). The EN 13501-1 regulation is ordered in classes from A1 (non-combustible material) to F (extremely flammable material). A comparison of the classes is not possible because the methods and evaluation criteria are completely different. The comparison table below is being considered purely indicative.

Is possible to provide the sandwich panels for the OVER units with air flow from the top. This implies that the air intake must necessarily be from the base of the unit with front blind paneling. The accessory increases the unit weight:

SIZE E1

E2

E3

E4

E5

E6

E7

E8

E9

OVER

Weight increasing (1)

kg

26

42

48

64

72

86

100

115

--

UNDER

Weight increasing (1)

kg

30

48

55

70

86

110

130

145

165

1. Add this value to the total unit weight

Definition

Italian classes

EN 13501-1

Non-combustible material

Class 0

A1

Combustible material, very limited contribution to fire

Class 1

A2 – B

Combustible material, limited contribution to fire

Class 2

A2 – B - C

Combustible material, medium contribution to fire

Class 3

C – D

Combustible material, highly contribution to fire

Class 4

E

Combustible material, easily flammable

Class 5

F

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

66

MEHITS S.p.A.

DATA BOOK

MACHINE DRAWINGS

Dimensions in mm - UNDER E1

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

67

MEHITS S.p.A.

DATA BOOK

MACHINE DRAWINGS - Dimensions in mm - UNDER E2

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

68

MEHITS S.p.A.

DATA BOOK

MACHINE DRAWINGS - Dimensions in mm - UNDER E3

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

69

MEHITS S.p.A.

DATA BOOK

MACHINE DRAWINGS - Dimensions in mm - UNDER E4

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

70

MEHITS S.p.A.

DATA BOOK

MACHINE DRAWINGS - Dimensions in mm - UNDER E5

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

71

MEHITS S.p.A.

DATA BOOK

MACHINE DRAWINGS - Dimensions in mm - UNDER E6

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

72

MEHITS S.p.A.

DATA BOOK

MACHINE DRAWINGS - Dimensions in mm - UNDER E7

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

73

MEHITS S.p.A.

DATA BOOK

MACHINE DRAWINGS - Dimensions in mm - UNDER E8

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

74

MEHITS S.p.A.

DATA BOOK

MACHINE DRAWINGS - Dimensions in mm - UNDER E9

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

75

MEHITS S.p.A.

DATA BOOK

MACHINE DRAWINGS - Dimensions in mm - OVER E1

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

76

MEHITS S.p.A.

DATA BOOK

MACHINE DRAWINGS - Dimensions in mm - OVER E2

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

77

MEHITS S.p.A.

DATA BOOK

MACHINE DRAWINGS - Dimensions in mm - OVER E3

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

78

MEHITS S.p.A.

DATA BOOK

MACHINE DRAWINGS - Dimensions in mm - OVER E4

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

79

MEHITS S.p.A.

DATA BOOK

MACHINE DRAWINGS - Dimensions in mm - OVER E5

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

80

MEHITS S.p.A.

DATA BOOK

MACHINE DRAWINGS - Dimensions in mm - OVER E6

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

81

MEHITS S.p.A.

DATA BOOK

MACHINE DRAWINGS - Dimensions in mm - OVER E7

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

82

MEHITS S.p.A.

DATA BOOK

MACHINE DRAWINGS - Dimensions in mm - OVER E8

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

83

MEHITS S.p.A.

DATA BOOK

HOLE IN THE RAISED FLOOR FOR DOWNFLOW VERSION

HOLE IN THE RAISED FLOOR WITHOUT FLOOR STAND

Foresee a hole in the floor with the following dimensions:

SIZE E1

E2

E3

E4

E5

E6

E7

E8

E9 a mm

95

110

110 b mm

560

660

785

c

mm

560

695

995

1185

1510

1755

2055

2380

2780

HOLE IN THE RAISED FLOOR WITH FLOOR STAND (OPTION)

Foresee a hole in the floor with the following dimensions:

SIZE E1

E2

E3

E4

E5

E6

E7

E8

E9 a mm

50

b

mm

670

770

925

925 c mm

670

805

1105

1325

1650

1895

2195

2520

2920

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

84

MEHITS S.p.A.

DATA BOOK

EXAMPLE FOR MACHINES NOISE EMISSION CALCULATION

UNDER MACHINE WITH DUCT ON AIR INTAKE

Duct

Lp A = Front side Under catalogue value

Lp B = Air delivery Under catalogue value

Lp C = Air intake Under catalogue value

The points B and C do not influence the point A

UNDER MACHINE UNDER WITH PLENUM ON AIR DELIVERY

Lp A = Front side Under catalogue value

Lp B = Air delivery Under catalogue value –plenum noise reduction

Lp C = Air intake Under catalogue value

Lp A+C = 10 log10 (10 +10 )

The point B do not influence the point A

LpA 10

LpC 10

UNDER MACHINE WITH PLENUM ON AIR INTAKE

Lp A = Front side Under catalogue value

Lp B = Air delivery Under catalogue value

Lp C = Air intake Under catalogue value – plenum noise reduction

Lp A+C = 10 log10 (10 +10 )

The point B do not influence the point A

LpA 10

LpC 10

OVER MACHINE WITH DUCT

Lp A = Air intake Over catalogue value

Lp B = Air delivery Over catalogue value

The point B do not influence the point A

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

85

MEHITS S.p.A.

DATA BOOK

EXAMPLE FOR MACHINES NOISE EMISSION CALCULATION

IMPORTANT The declared noise levels are intended in free field conditions. The noise pressure level of an installed unit is affected by the room acoustic characteristics. Please consider an average noise increase of +4/+6 dB(A).

OVER MACHINE WITH PLENUM ON AIR DELIVERY

Lp A = Air intake Over catalogue value

Lp B = Air delivery Over catalogue value – plenum noise reduction

Lp A+B = 10 log10 (10 +10 )

LpA 10

LpC 10

OVER MACHINE WITH DUCT AND PLENUM ON AIR DELIVERY

Lp A = Front side Over catalogue value

Lp B = Air delivery Over catalogue value

Lp C = Lp A + 6dB(A) – plenum noise reduction

Lp A+C = 10 log10 (10 +10 )

The point B do not influence the point A+C

LpA 10

LpC 10

OVER MACHINE WITH DUCT AND PLENUM ON AIR DELIVERY

Lp A = Front side Over catalogue value

Lp B = Air delivery Over catalogue value

Lp C = Lp D = Lp A + 6 dB(A) – plenum noise reduction

The points B, C and D do not influence the point A Blind front panel

Blind front panel

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

86

MEHITS S.p.A.

DATA BOOK

VALVE PRESSURE DROP CALCULATION AS FUNCTION OF WATER FLOW RATE

Flow coefficient kv defines the water flow (between 5°C and 40°C) expressed in m3/h that cross a valve with a pressure drop of 1bar (100kPa).

With this data is possible to calculate the localized pressure drop as function of the water flow rate.

P = (Q / kv)

2

P (bar) = localized pressure drop of valve; Q (m3/h) = water flow rate – it varies according to the desired operating condition; k

v

(m3/h) = valve flow coefficient.

The formula allows to calculate the value of the localized pressure drop (in bar). The pressure drops values showed on the documentation are supplied in kPa. Is possible to change from one unit to another through the following conversion.

1 bar = 100kPa

CALCULATION EXAMPLE OF 2-WAY VALVE FOR BY-PASS PRESSURE DROP IN FUNCTION OF WATER FLOW RATE

Model 092 P2 D E8

Example at nominal conditions. Characteristics referred to entering air at 26°C-40%RH with chilled water temperature 7-12°C - 0% glycol

Water flow rate: 19,9 m3/h Valve flow coefficient kv: 25 m3/h

2-way valve for by-pass pressure drop: P = (Q / kv) 2 = (19,9/ 25) 2 = 0,633 (bar) * 100 (kPa / bar) = 63,3 kPa

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

87

MEHITS S.p.A.

DATA BOOK

AIR FILTERS REPLACEMENT FOR UNDER VERSION MACHINES SIZE E4 – E5 – E6 – E7 – E8 – E9

Installation with an obstacle

on the top

600 mm

minimum

Installation with an air intake

plenum with noise partitions

Installation with a Free-

Cooling plenum

Installation with an

air intake duct

450 mm

minimum

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

88

MEHITS S.p.A.

DATA BOOK

SHIPMENT: PACKING DIMENSIONS

Values referred to basic machine. The presence of some accessories increases the weight of machine.

The machines are shipped on pallet and covered with shrink wrap. On request packing on pallet covered with shrink wrap and wooden cage.

Size

A

(mm) B (mm) H (mm)

Size

A

(mm) B (mm) H (mm)

H1 (*)

(mm)

E1

750

2080 E1

790

2150

2350

E2

900

750

2080 E2

940

790

2150

2350

E3

1200

910

2080 E3

1240

950

2150

2350

E4

1400

1050

2130 E4

1440

1090

2200

2350

E5

1750

1050

2130 E5

1790

1090

2200

2350

E6

2000

1050

2130 E6

2040

1090

2200

2350

E7

2280

1050

2130 E7

2320

1090

2200

2350

E8

2650

1050

2130 E8

2690

1090

2200

2350

E9

3000

1050

2130 E9

3040

1090

2200

2350

H1 (*) = Packing height with optional A531 on/off damper

SHIPMENT: SHIPPING WEIGHT

STANDARD PACKING

Model

011 P1

S

014 P1

S

016 P1

S

020 P1

S

022 P1

S

026 P1

S

032 P1

S

037 P1

S

041 P1

S

045 P1

S

Size E1

E2

E3

E4

Weight UNDER

kg

272

308,2

313,2

374

379

501,5

506,5

518,5

526,5

Weight OVER

kg

262

298,2

303,2

354

359

491,5

496,5

508,5

516,5

Model

039 P2

D

048 P2

D

055 P2

D

062 P2

D

075 P2

D

082 P2

D

092 P2

D

102 P2

D

117 P4

D

146 P4

D

Size E5

E5

E6

E7

E8

E9

Weight UNDER

kg

630

640

734,5

754,5

880

885

1000,5

1211,5

1271,5

Weight OVER

kg

620

630

724,5

744,5

823

830

940,5

--

STANDARD PACKING

DIMENSIONS

OPTIONAL 9973: WOODEN CAGE PACKING

DIMENSIONS

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

89

MEHITS S.p.A.

DATA BOOK

OPTIONAL 9973: WOODEN CAGE PACKING

Model

011 P1

S

014 P1

S

016 P1

S

020 P1

S

022 P1

S

026 P1

S

032 P1

S

037 P1

S

041 P1

S

045 P1

S

Size E1

E2

E3

E4

Weight UNDER

kg

299

336,2

341,2

406

411

537,5

542,5

554,5

562,5

Weight UNDER (1)

kg

321

361,2

366,2

439

444

581,5

586,5

598,5

606,5

Weight OVER

kg

289

326,2

331,2

386

391

527,5

532,5

544,5

552,5

Weight OVER (1)

kg

311

351,2

356,2

419

424

571,5

576,5

588,5

596,5

Model

039 P2

D

048 P2

D

055 P2

D

062 P2

D

075 P2

D

082 P2

D

092 P2

D

102 P2

D

117 P4

D

146 P4

D

Size E5

E5

E6

E7

E8

E9

Weight UNDER

kg

666

676

778,5

798,5

932

937

1050,5

1269,5

1329,5

Weight UNDER (1)

kg

721

731

841,5

861,5

1004

1009

1133,5

1367,5

1427,5

Weight OVER

kg

656

666

768,5

788,5

875

882

990,5

--

Weight OVER (1)

kg

711

721

831,5

851,5

947

954

1073,5

--

(1) Machine with optional A531 on/off damper

SHIPMENT: OPTIONALS PACKING DIMENSIONS AND SHIPPING WEIGHT

P011 - EMPTY PLENUM P012 - EMPTY PLENUM CL.A1 P031 - EMPTY INTAKE PLENUM P032 - EMPTY INTAKE PLENUM CL.A1 P013 - PLENUM + 3 GRILLES P014 - PLENUM + 3 GRILLES CL.A1 P015 - SILENCED PLENUM P016 - SILENCED PLENUM + 1 GRILLE P017 - PLENUM + FILTER EPM2.5 50% P018 - PLENUM + FILTER EPM1 50% P019 - PLENUM + FILTER EPM1 85%

The plenums are shipped on pallet and covered with shrink wrap.

Size E1

E2

E3

E4

E5

E6

E7

E8

E9

DIMENSIONS

A

mm

750

900

1200

1400

1750

2000

2280

2650

3000

B

mm

750

910

1050

H

mm

630

SHIPPING WEIGHT

P011 - Empty plenum “O” / “U”

kg

31

34

41

53

69

78

88

105

122

P012 - Empty plenum CL.A1 “O” / “U”

kg

36

39

47

62

79

89

100

119

137

P031 - Empty intake plenum “O” / “U”

kg

31

34

41

53

69

78

88

105

122

P032 - Empty intake plenum CL. A1 “O” / “U”

kg

36

39

47

62

79

89

100

119

137

P013 - Plenum + 3 grilles “O” / “U”

kg

32

35

47

68

79

96

106

135

152

P014 - Plenum + 3 grilles CL. A1 “O” / “U”

kg

36

40

54

77

90

107

122

151

170

P015 - Silenced plenum “O” / “U”

kg

36

39

47

68

81

98

113

130

152

P016 - Silenced plenum + 1 grille“O” / “U”

kg

41

44

54

88

101

111

126

155

182

P017 - P018 - P019 – Plenum + filter “O” / “U”

kg

37

39

47

68

84

98

118

135

152

“O” Over / “U” Under

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

90

MEHITS S.p.A.

DATA BOOK

P034: INTAKE FREE-COOLING PLENUM

The plenums are shipped on pallet and covered with shrink wrap.

Size E1

E2

E3

E4

E5

E6

E7

E8

E9

DIMENSIONS

A

mm

750

900

1200

1400

1750

2000

2280

2650

3000

B

mm

750

910

1050

H

mm

630

750

SHIPPING WEIGHT

P034 - Intake free-cooling plenum “U”

kg

35

39

52

76

90

111

128

155

182

P034 - Intake free-cooling plenum “O”

kg

35

39

52

76

90

111

128

155

182

“O” Over / “U” Under

P041 / P042 / P043: SUPPORT FRAME

The support frames are shipped on pallet and covered with shrink wrap.

Size E1

E2

E3

E4

E5

E6

E7

E8

E9

DIMENSIONS

A

mm

1200

1400

1750

2000

2280

2650

3000

B

mm

900

H

mm

500

SHIPPING WEIGHT

kg

26

27

29

37

40

44

47

49

53

P183 / P184: KIT NETWORK ANALYZER / KIT NETWORK ANALYZER+OPTIONAL P113 / P114: DUAL POWER SUPPLY KIT / DUAL POWER SUPPLY KIT+OPTIONAL

The optional are shipped in a cardboard box.

P183 / P184 - KIT NETWORK ANALYZER / KIT NETWORK ANALYZER+OPTIONAL

P113 / P114 - DUAL POWER SUPPLY KIT / DUAL POWER SUPPLY KIT+OPTIONAL

Size E1

E2

E3

E4

E5

E6

E7

E8

E9

DIMENSIONS

A

mm

410

--

B

mm

410

--

H

mm

210

--

SHIPPING WEIGHT

kg 5 5 5 5

--

Size E1

E2

E3

E4

E5

E6

E7

E8

E9

DIMENSIONS

A

mm

400

--

B

mm

400

--

H

mm

210

--

SHIPPING WEIGHT

kg

12

--

t-NEXT DF DX

T_tNEXTDFDX_0719_EN

91

MEHITS S.p.A.

DATA BOOK

Via Caduti di Cefalonia, 1 - 36061 Bassano del Grappa (VI) Italy

Ph. (+39) 0424 509 500 • Fax (+39) 0424 509 509

www.melcohit.com

©Mitsubishi Electric Hydronics & IT Cooling Systems S.p.A. The Company reserves the right to make any variation in technical specification to the equipment

described, or to withdraw or replace products without prior notification or public announcement. Mitsubishi Electric Hydronics & IT Cooling Systems S.p.A. is constantly developing and improving its products. All descriptions, illustrations, drawings and specifications present in this publication are general information and shall not part of any contract. All goods are supplied subject to the Company’s General Conditions of Sales, a copy of which is available on request. Third-party product and brand names may be trademarks or registered trademarks of their respective owners.

Mitsubishi Electric t-NEXT DF DX 011 P1 S, t-NEXT DF DX 016 P1 S, t-NEXT DF DX 014 P1 S, t-NEXT DF DX 020 P1 S, t-NEXT DF DX 022 P1 S User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual