MITSUBISHI MF-10KDS-T12-06x, MF-10KDS-T12-07x, MF-10KDS-R13-06x, MF-10KDS-R13-07x User Manual
MF-10KDS-T12-06x/07x
MF-10KDS-R13-06x/07x
DESCRIPTION
Th is prod uct is designed to provide high optic al
performance for SDH STM-64/SONE T OC-192.
Trans mitte r us es co oled laser in a but t erf ly pac kag e
module wit h driv ered by spec ific integrated circuit.
Receiver us es PD preamp -modul e (butterf ly package
module) and integrat ed circuit s for reshaping, retim ing
and regenerating optical signal.
FEATURES
Full SONET/SDH line up
K connector interface
-5.2V,+5V power supply target, -2.2V(TX only)
Case Temp. Range: 10 to 65°C
Clock recovery and digital alarm function.
APPLICATION
Short haul and long haul telecommunication systems
for SDH STM64 / SONET OC-192.
MITSUBISHI (OPTICAL DEVICES)
SONET/SDH TRANSMITTER & RECIEVER
ABSOLUTE MAXIMUM RATINGS
Stress below listed absolute maximum rating may cause permanent damage to the transmitter and receiver.
This is a stress only and func tional operation of the transceiver at these or any other conditions in excess of those
given in the operational sections of this data sheet is not implied.
Exposure to Absolute Maximum Rating for extended periods may affect transmitter and receiver reliability.
Tc=25°C
Parameters Symbol Ratings Unit
Vcc +5.3 V
Vee -6.0 VSupply voltage
Vtt -2.4 V
Storage temperature Tstg -40 to 85
Operating case temperature Tc 10 to 65
Relative humidity(non condensation) - 10 to 80 %
Fiber bend radius rF 32 mm
C
°
C
°
MITSUBISHI (OPTICAL DEVICES)
MF-10KDS-T12-06x/07x
MF-10KDS-R13-06x/07x
SONET/SDH TRANSMITTER & RECIEVER
ELECTRICAL CHARACTERISTICS
All parameters are specified over the operating case temperature.
Measurement conditions are at 9953.28Mb/s+/-20ppm, NRZ PN2
Vcc=+5.0V+/-5%, Vee=-5.2V+/-5%, Vtt=-2.2V+/-0.1V,Tc=10 to 65 °C, Using a PRBS 2
50%Mark ratio, unless otherwise noted.
Transmitter
Parameters Condition Symbol Min. Typ. Max. Unit
Supply voltage
Supply current
23
-1 and 50%duty cycle data signal.
Vee -5.46 -5.2 -4.94 V
Vcc 4.75 5.0 5.25 V
Vtt -2.3 -2.2 -2.1 V
Iee - - 1.5 A
Icc - - 1.0 A
23
-1 pattern with a
Itt - Data / Clock input voltage (DC:50ohm) note 1 - SCFL Data / Clock relationship note 5 Td -20 - +20 psec
Function note 2,3 -
Sh utdow n, Laser Degr adati on, Power out
of rang e Alarm, Laser Over Tem pera ture
Alarm
1. 2
Receiver
Parameters Condition Symbol Min. Typ. Max. Unit
Vee -5.46 -5.2 -4.94 V
Supply voltage
Vcc 4.75 5.0 5.25 V
Iee - - 1.5 A
Supply current
Icc - - 1.5 A
Data output voltage (DC:50ohm) note 4 - SCFL -
Clock output voltage (AC:50ohm) note 4 0.5 - 1.5 Vpp
Data / Clock relationship note 5 Td -25 - +25 psec
A
-
Jitter - TBD -
Function note 6 - Loss of Signal Alarm -
MITSUBISHI (OPTICAL DEVICES)
MF-10KDS-T12-06x/07x
MF-10KDS-R13-06x/07x
SONET/SDH TRANSMITTER & RECIEVER
OPTICAL CHARACTERISTICS
Parameter Symbol Specification Unit
ITU code - S-64.2 S-64.3 -
- - Min. Max. Min. Max. Dispersion - -800 +800 -130 +130 ps/nm
Optical path penalty Pp - 2 - 1 dB
Transmitter
Wavelength - 1530 1565 1530 1565 Optical output power Pout -3 +3 -2 +3 dBm
Spectral width(-20dB) - - 0.5 - 0.5 nm
SMSR - 30 - 30 - dB
Extinction Ratio Ex 8.2 - 8.2 - dB
Receiver
Sensitivity - - -14 - -13 dBm
Overload - -3 - -3 - dBm
note : Bit Rate 9953.28Mb/s,PRBS223-1, BER<=10
-12
ORDERING INFORMATION
Transmitter
Part number ITU-code Optical connector type
MF-10KDS-T12-060 S-64.2 FC
MF-10KDS-T12-061 S-64.2 SC
MF-10KDS-T12-070 S-64.3 FC
MF-10KDS-T12-071 S-64.3 SC
Receiver
Part number ITU-code Optical connector type
MF-10KDS-R13-060 S-64.2 FC
MF-10KDS-R13-061 S-64.2 SC
MF-10KDS-R13-070 S-64.3 FC
MF-10KDS-R13-071 S-64.3 SC
Loading...