Mitsubishi M37515M4-XXXHP Datasheet
MITSUBISHI MICROCOMPUTERS
M37515M4-XXXHP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
DESCRIPTION
The M37515M4-XXXHP is the 8-bit microcomputer based on the
740 family core technology.
The M37515M4-XXXHP is designed for the household products
and office automation equipment and includes serial I/O functions,
8-bit timer, A-D converter, and I
2
C-bus interface.
FEATURES
●Basic machine-language instructions ...................................... 71
●Minimum instruction execution time .................................. 0.5 µs
(at 8 MHz oscillation frequency)
●Memory size
ROM .............................................................................16 Kbytes
RAM .............................................................................. 512 bytes
●Programmable input/output ports ............................................ 40
●Interrupts ................................................. 16 sources, 16 vectors
●Timers ............................................................................. 8-bit ✕ 4
●Serial I/O ....................... 8-bit ✕ 1(UART or Clock-synchronized)
●Multi-master I
2
C-bus interface (option) ....................... 1 channel
●P WM ............................................................................... 8-bit ✕ 1
●A-D converter ............................................... 10-bit ✕ 8 channels
●Watchdog timer ............................................................ 16-bit ✕ 1
●Clock generating circuit..................................... Built-in 2 circuits
(connect to external ceramic resonator or quartz-crystal oscillator)
PIN CONFIGURATION (TOP VIEW)
●Power source voltage
In high-speed mode .................................................. 4.0 to 5.5 V
(at 8 MHz oscillation frequency)
In high-speed mode .................................................. 2.7 to 5.5 V
(at 4 MHz oscillation frequency)
In middle-speed mode............................................... 2.7 to 5.5 V
(at 8 MHz oscillation frequency)
In low-speed mode.................................................... 2.7 to 5.5 V
(at 32 kHz oscillation frequency)
●Power dissipation
In high-speed mode .......................................................... 34 mW
(at 8 MHz oscillation frequency, at 5 V power source voltage)
In low-speed mode............................................................ 60 µW
(at 32 kHz oscillation frequency, at 3 V power source voltage)
●Operating temperature range....................................–20 to 85°C
APPLICATION
Office automation equipment, FA equipment, Household products,
Consumer electronics, etc.
P35/AN
P34/AN
P33/AN
P32/AN
P31/AN
P30/AN
V
V
AV
P4
P4
P4
REF
6
7
/AN
/AN
6
0
7
P3
P0
P3
3635343332
37
5
4
38
3
39
2
40
1
41
0
42
CC
SS
7
6
5
M37515M4-XXXHP
43
44
45
46
47
48
1
23456
1
2
/INT
/INT
2
3
/PWM
3
P4
P4
/INT
4
P4
1
P0
0
/INT
1
P4
3
2
P0
P0
31
1
RDY
/S
0
/CNTR
0
P4
/CNTR
7
P2
4
5
P0
P0
302928
7
8
D
X
CLK
/T
/S
2
6
P2
/SCL
5
P2
6
P0
9
D
X
/R
2
/SDA
4
P2
7
P0
27
10
1
/SCL
3
P2
0
P1
26
11
1
/SDA
2
P2
1
P1
25
12
SS
CNV
24
P1
23
22
21
20
19
18
17
16
15
14
13
2
P13(LED0)
P14(LED1)
5
(LED2)
P1
P16(LED3)
P17(LED4)
SS
V
X
OUT
X
IN
RESET
P20 /X
COUT
P21/X
CIN
Package type : 48P6D-A (48-pin plastic-molded LQFP)
Fig. 1 M37515M4-XXXHP pin configuration
1
FUNCTIONAL BLOCK
INT
0
–
CNTR
0
CNTR
1
V
REF
AV
SS
R A M
R O M
C P U
A
X
Y
S
PC
H
PCLPS
V
SS
18
RESET
15
V
CC
43 12
CNV
SS
44 45
X
IN
16
17
SI/O(8)
Reset input
Clock generating circuit
Main-clock
input
Main-clock
output
A-D
converter
(10)
Timer Y( 8 )
Timer X( 8 )
Prescaler 12(8)
Prescaler X(8)
Prescaler Y(8)
Timer 1( 8 )
Timer 2( 8 )
Sub-clock
input
X
OUT
X
CIN
X
COUT
Sub-clock
output
Watchdog
timer
Reset
P2(8)
P3(8)
I/O port P2
I/O port P3
P4(8)
I/O port P4
I C
INT
3
1
35
2
4
36
3835 37
39
6 8 10 147 9 11 13
P1(8)
I/O port P1
19 21 23 2520 22 24 26
P0(8)
I/O port P0
27 282930 31 32 33 34
PWM
(8)
2
X
CIN
X
COUT
484746
40
41 42
MITSUBISHI MICROCOMPUTERS
M37515M4-XXXHP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
FUNCTIONAL BLOCK DIAGRAM
Fig. 2 Functional block diagram
2
PIN DESCRIPTION
Table 1 Pin description
MITSUBISHI MICROCOMPUTERS
M37515M4-XXXHP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
VCC, VSS
RESET
IN
X
XOUT
P00–P07
P10–P17
P20/XCOUT
P21/XCIN
P22/SDA1
P23/SCL1
P24/SDA2/RxD
P25/SCL2/TxD
P26/SCLK
P27/CNTR0/
SRDY
P30/AN0–
P37/AN7
P40/CNTR1
P41/INT0–
P43/INT2
P44/INT3/PWM
P45–P47
NamePin
Power source
SS inputCNVSS
CNV
Reset input
Clock input
Clock output
I/O port P0
I/O port P1
I/O port P2
I/O port P3
I/O port P4
Functions
•Apply voltage of 2.7 V – 5.5 V to Vcc, and 0 V to Vss.
•This pin controls the operation mode of the chip.
•Normally connected to V
•Reset input pin for active “L.”
•Input and output pins for the clock generating circuit.
•Connect a ceramic resonator or quartz-crystal oscillator between the X
the oscillation frequency.
•When an external clock is used, connect the clock source to the XIN pin and leave the XOUT
pin open.
•8-bit CMOS I/O port.
•I/O direction register allows each pin to be individually programmed as either input or output.
•CMOS compatible input level.
•CMOS 3-state output structure.
•P1
3 to P17 (5 bits) are enabled to output large current for LED drive.
•8-bit CMOS I/O port.
•I/O direction register allows each pin to be individually
programmed as either input or output.
•CMOS compatible input level.
•P22 to P25 can be switched between CMOS compatible input level or SMBUS input level in the I2C-BUS
interface function.
•P20, P21, P24 to P27: CMOS3-state output structure.
•P24, P25: N-channel open-drain structure in the I2CBUS interface function.
•P2
2, P23: N-channel open-drain structure.
•8-bit CMOS I/O port with the same function as port P0.
•CMOS compatible input level.
•CMOS 3-state output structure.
•8-bit CMOS I/O port with the same function as port P0.
•CMOS compatible input level.
•CMOS 3-state output structure.
SS.
Function except a port function
IN and XOUT pins to set
• Sub-clock generating circuit I/O
pins (connect a resonator)
• I2C-BUS interface function pins
• I2C-BUS interface function pin/
Serial I/O function pins
• Serial I/O function pin
• Serial I/O function pin/
Timer X function pin
• A-D converter input pin
• Timer Y function pin
• Interrupt input pins
• Interrupt input pin
• PWM output pin
3
FUNCTIONAL DESCRIPTION
CENTRAL PROCESSING UNIT (CPU)
The M37515M4-XXXHP uses the standard 740 Family instruction
set. Refer to the table of 740 Family addressing modes and machine instructions or the 740 Family Software Manual for details
on the instruction set.
Machine-resident 740 Family instructions are as follows:
The FST and SLW instructions cannot be used.
The STP, WIT, MUL, and DIV instructions can be used.
[CPU Mode Register (CPUM)] 003B16
The CPU mode register contains the stack page selection bit, etc.
The CPU mode register is allocated at address 003B
16.
MITSUBISHI MICROCOMPUTERS
M37515M4-XXXHP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
b7
b0
CPU mode register
(
CPUM : address
003B16)
Processor mode bits
b1 b0
0 0 : Single-chip mode
0 1 :
1 0 : Not available
1 1 :
Stack page selection bit
0 : 0 page
1 : 1 page
Not used (return “1” when read)
(Do not write “0” to this bit.)
C
switch bit
Port X
0 : I/O port function (stop oscillating)
CIN–XCOUT
1 : X
Main clock (X
0 : Oscillating
1 : Stopped
Main clock division ratio selection bits
b7 b6
0 0 : φ = f(XIN)/2 (high-speed mode)
0 1 : φ = f(X
1 0 : φ = f(X
1 1 : Not available
IN–XOUT
oscillating function
) stop bit
IN
)/8 (middle-speed mode)
CIN
)/2 (low-speed mode)
Fig. 3 Structure of CPU mode register
4
MITSUBISHI MICROCOMPUTERS
M37515M4-XXXHP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MEMORY
Special Function Register (SFR) Area
The Special Function Register area in the zero page contains control registers such as I/O ports and timers.
RAM
RAM is used for data storage and for stack area of subroutine
calls and interrupts.
ROM
The first 128 bytes and the last 2 bytes of ROM are reser ved for
device testing and the rest is user area for storing programs.
Interrupt Vector Area
The interrupt vector area contains reset and interrupt vectors.
0000
16
0040
16
0100
16
RAM
512 bytes
Zero Page
Access to this area with only 2 bytes is possible in the zero page
addressing mode.
Special Page
Access to this area with only 2 bytes is possible in the special
page addressing mode.
SFR area
Zero page
ROM
16 Kbytes
023F
0440
C000
C080
FF00
FFDC
FFFE
FFFF
16
Reserved area
16
Not used
16
Reserved ROM area
(128 bytes)
16
16
16
Interrupt vector area
16
Reserved ROM area
16
Special page
Fig. 4 Memory map diagram
5
MITSUBISHI MICROCOMPUTERS
M37515M4-XXXHP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
0000
0001
0002
0003
0004
0005
0006
0007
0008
0009
000A
000B
000C
000D
000E
000F
0010
0011
0012
0013
0014
0015
0016
0017
0018
0019
001A
001B
001C
001D
001E
001F
Port P0 (P0)
16
Port P0 direction register (P0D)
16
Port P1 (P1)
16
Port P1 direction register (P1D)
16
Port P2 (P2)
16
Port P2 direction register (P2D)
16
Port P3 (P3)
16
Port P3 direction register (P3D)
16
Port P4 (P4)
16
Port P4 direction register (P4D)
16
16
16
16
16
16
16
16
16
16
16
16
16
Reserved ✽
16
Reserved ✽
16
Reserved ✽
Transmit/Receive buffer register (TB/RB)
16
Serial I/O status register (SIOSTS)
16
Serial I/O control register (SIOCON)
16
UART control register (UARTCON)
16
Baud rate generator (BRG)
16
PWM control register (PWMCON)
16
PWM prescaler (PREPWM)
16
PWM register (PWM)
16
✽ Reserved : Do not write “1” to this address.
0020
0021
0022
0023
0024
0025
0026
0027
0028
0029
002A
002B
002C
002D
002E
002F
0030
0031
0032
0033
0034
0035
0036
0037
0038
0039
003A
003B
003C
003D
003E
003F
Prescaler 12 (PRE12)
16
Timer 1 (T1)
16
Timer 2 (T2)
16
Timer XY mode register (TM)
16
Prescaler X (PREX)
16
Timer X (TX)
16
Prescaler Y (PREY)
16
Timer Y (TY)
16
Timer count source selection register (TCSS)
16
16
16
2C
16
data shift register (S0)
I
2
16
C address register (S0D)
I
2
16
C status register (S1)
I
2
16
C control register (S1D)
I
2C
16
clock control register (S2)
I
2
16
C start/stop condition control register (S2D)
I
16
16
16
A-D control register (ADCON)
16
A-D conversion low-order register (ADL)
16
A-D conversion high-order register (ADH)
16
16
MISRG
16
Watchdog timer control register (WDTCON)
16
Interrupt edge selection register (INTEDGE)
16
CPU mode register (CPUM)
16
Interrupt request register 1 (IREQ1)
16
Interrupt request register 2 (IREQ2)
16
Interrupt control register 1 (ICON1)
16
Interrupt control register 2 (ICON2)
16
Fig. 5 Memory map of special function register (SFR)
6
MITSUBISHI MICROCOMPUTERS
M37515M4-XXXHP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
I/O PORTS
The I/O ports have direction registers which determine the input/
output direction of each individual pin. Each bit in a direction register corresponds to one pin, and each pin can be set to be input
port or output port.
When “0” is written to the bit corresponding to a pin, that pin becomes an input pin. When “1” is written to that bit, that pin
becomes an output pin.
If data is read from a pin which is set to output, the value of the
port output latch is read, not the value of the pin itself. Pins set to
input are floating. If a pin set to input is written to, only the por t
output latch is written to and the pin remains floating.
Table 2 I/O port function
Pin
P00–P07
P10–P17
P20/XCOUT
P21/XCIN
P22/SDA1
P23/SCL1
P24/SDA2/RxD
P25/SCL2/TxD
P26/SCLK
P27/CNTR0/SRDY
P30/AN0—
P37/AN7
P40/CNTR1
P41/INT0—
P43/INT2
P44/INT3/PWM
P45—P47 (1)
Name
Port P0
Port P1
Port P2
Port P3
Port P4
Input/Output
Input/output,
individual
bits
I/O Structure Non-Port Function
CMOS compatible
input level
CMOS 3-state output Sub-clock generating
CMOS compatible
input level
CMOS/SMBUS input
level (when selecting
2
I
C-BUS interface
function)
N-channel open-drain
output
CMOS compatible
input level
CMOS/SMBUS input
level (when selecting
I2C-BUS interface
function)
CMOS 3-state output
N-channel open-drain
output (when
selecting I2C-BUS
interface function)
CMOS compatible
input level
CMOS 3-state output
circuit
I2C-BUS interface function I/O
2
C-BUS interface func-
I
tion I/O
Serial I/O function I/O
Serial I/O function I/O
Serial I/O function I/O
Timer X function I/O
A-D conversion input
Timer Y function I/O
External interrupt input
External interrupt input
PWM output
Related SFRs
CPU mode register
2
I
C control register
I2C control register
Serial I/O control
register
Serial I/O control
register
Serial I/O control
register
Timer XY mode register
A-D control register
Timer XY mode register
Interrupt edge selection
register
Interrupt edge selection
register
PWM control register
Ref.No .
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
7
MITSUBISHI MICROCOMPUTERS
M37515M4-XXXHP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(1) Port P0, P1, P45P4
Data bus
(3) Port P2
Data bus
(5) Port P2
SDA/SCL pin selection bit
Data bus
1
Port XC switch bit
2
I C-BUS interface enable bit
3
–
Direction
register
Port latch
Direction
register
Port latch
Sub-clock generating circuit input
Direction
register
Port latch
7
(2) Port P2
Data bus
(4) Port P2
2
I C-BUS interface enable bit
SDA/SCL pin selection bit
Data bus
(6) Port P2
SDA/SCL pin selection bit
0
Port XC switch bit
Direction
register
Port latch
2
Direction
register
Port latch
SDA output
4
2
I C-BUS interface enable bit
Serial I/O enable bit
Receive enable bit
Port P2
SDA input
1
Port X
Oscillator
C
switch bit
SCL output
(7) Port P2
2
I C bus interface enable bit
SDA/SCL pin selection bit
Data bus
5
P-channel output disable bit
Serial I/O enable bit
Transmit enable bit
Direction
register
Port latch
Serial I/O output
SCL output
Fig. 6 Port block diagram (1)
SCL input
SCL input
Data bus
SDA output
(8) Port P2
Serial I/O enable bit
Serial I/O clock selection bit
Serial I/O mode selection bit
Data bus
6
Serial I/O enable bit
Direction
register
Port latch
Serial clock output
Direction
register
Port latch
SDA input
Serial I/O input
External clock input
8
MITSUBISHI MICROCOMPUTERS
M37515M4-XXXHP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(9) Port P2
Serial I/O mode selection bit
Serial I/O enable bit
S
RDY
Data bus
Serial ready output
(11) Port P4
7
Pulse output mode
output enable bit
Direction
register
Port latch
Pulse output mode
Timer output
0
Data bus Port latch
Direction
register
Pulse output mode
Timer output
CNTR
0
interrupt
CNTR1 interrupt input
input
(10) Port P30–P3
Data bus
(12) Port P41–P4
Data bus
7
Direction
register
Port latch
A-D converter input
3
Direction
register
Port latch
Analog input pin selection bit
Interrupt input
(13) Port P4
Data bus
4
PWM output enable bit
Direction
register
Port latch
PWM output
Fig. 7 Port block diagram (2)
9
MITSUBISHI MICROCOMPUTERS
M37515M4-XXXHP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
INTERRUPTS
Interrupts occur by 16 sources among 16 sources: seven external,
eight internal, and one software.
Interrupt Control
Each interrupt is controlled by an interrupt request bit, an interrupt
enable bit, and the interrupt disable flag except for the software interrupt set by the BRK instruction. An interrupt occurs if the
corresponding interrupt request and enable bits are “1” and the interrupt disable flag is “0”.
Interrupt enable bits can be set or cleared by software.
Interrupt request bits can be cleared by software, but cannot be
set by software.
The BRK instruction cannot be disabled with any flag or bit. The I
(interrupt disable) flag disables all interrupts except the BRK instruction interrupt.
When several interrupts occur at the same time, the interrupts are
received according to priority.
Interrupt Operation
By acceptance of an interrupt, the following operations are automatically performed:
1. The contents of the program counter and the processor status
register are automatically pushed onto the stack.
2. The interrupt disable flag is set and the corresponding interrupt
request bit is cleared.
3. The interrupt jump destination address is read from the vector
table into the program counter.
■Notes
When the active edge of an external interrupt (INT0–INT3, SCL/
SDA, CNTR
bit may also be set. Therefore, take the following sequence:
1. Disable the interrupt
2. Change the interrupt edge selection register
(S
timer XY mode register for CNTR
3. Clear the interrupt request bit to “0”
4. Accept the interrupt.
0, CNTR1) is set, the corresponding interrupt request
CL/SDA interrupt pin polarity selection bit for SCL/SDA; the
0 and CNTR1)
10
Table 3 Interrupt vector addresses and priority
Interrupt Source
Reset (Note 2)
INT0
SCL, SDA
1
INT
INT2
INT3
I2C
Timer X
Timer Y
Timer 1
Timer 2
Serial I/O
reception
Serial I/O
Transmission
0
CNTR
CNTR1
A-D converter
BRK instruction
Notes 1: Vector addresses contain interrupt jump destination addresses.
2: Reset function in the same way as an interrupt with the highest priority.
Priority
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Vector Addresses (Note 1)
High
FFFD16
FFFB16
FFF916
FFF716
FFF516
FFF316
FFF116
FFEF16
FFED16
FFEB16
FFE916
FFE716
FFE516
FFE316
FFE116
FFDF16
Low
FFFC
FFFA
16
FFF816
FFF616
FFF416
FFF216
FFF016
FFEE16
FFEC16
FFEA16
FFE816
FFE616
FFE416
FFE216
FFE016
FFDE16
16
FFDC16FFDD16
MITSUBISHI MICROCOMPUTERS
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Interrupt Request
Generating Conditions
At reset
At detection of either rising or
falling edge of INT0 input
At detection of either rising or
falling edge of SCL or SDA input
At detection of either rising or
falling edge of INT
At detection of either rising or
falling edge of INT
At detection of either rising or
falling edge of INT
At completion of data transfer
At timer X underflow
At timer Y underflow
At timer 1 underflow
At timer 2 underflow
At completion of serial I/O data
reception
At completion of serial I/O transfer shift or when transmission
buffer is empty
At detection of either rising or
falling edge of CNTR0 input
At detection of either rising or
falling edge of CNTR1 input
At completion of A-D conversion
At BRK instruction execution
1 input
2 input
3 input
M37515M4-XXXHP
Remarks
Non-maskable
External interrupt
(active edge selectable)
External interrupt
(active edge selectable)
External interrupt
(active edge selectable)
External interrupt
(active edge selectable)
External interrupt
(active edge selectable)
STP release timer underflow
Valid when serial I/O is selected
Valid when serial I/O is selected
External interrupt
(active edge selectable)
External interrupt
(active edge selectable)
Non-maskable software interrupt
11
Interrupt request bit
Interrupt enable bit
Interrupt disable flag (I)
MITSUBISHI MICROCOMPUTERS
M37515M4-XXXHP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Fig. 8 Interrupt control
b7 b0
b7 b0
BRK instruction
Interrupt edge selection register
(INTEDGE : address 003A
INT0 active edge selection bit
INT
1
active edge selection bit
INT
2
active edge selection bit
INT
3
active edge selection bit
Reserved (Do not write “1” to this bit)
Not used (returns “0” when read)
Interrupt request register 1
(IREQ1 : address 003C
INT0 interrupt request bit
SCL/SDA interrupt request bit
INT
1
interrupt request bit
INT
2
interrupt request bit
3
interrupt request bit
INT
2
C interrupt request bit
I
Timer X interrupt request bit
Timer Y interrupt request bit
0 : No interrupt request issued
1 : Interrupt request issued
16)
16)
Reset
0 : Falling edge active
1 : Rising edge active
b7 b0
Interrupt request
Interrupt request register 2
(IREQ2 : address 003D
Timer 1 interrupt request bit
Timer 2 interrupt request bit
Serial I/O reception interrupt request bit
Serial I/O transmit interrupt request bit
CNTR
0
interrupt request bit
CNTR
1
interrupt request bit
AD converter interrupt request bit
Not used (returns “0” when read)
0 : No interrupt request issued
1 : Interrupt request issued
16)
b7 b0
Interrupt control register 1
(ICON1 : address 003E
INT0 interrupt enable bit
SCL/SDA interrupt enable bit
1
interrupt enable bit
INT
INT
2
interrupt enable bit
INT
3
interrupt enable bit
2
C interrupt enable bit
I
Timer X interrupt enable bit
Timer Y interrupt enable bit
0 : Interrupts disabled
1 : Interrupts enabled
Fig. 9 Structure of interrupt-related registers (1)
12
16)
b7 b0
Interrupt control register 2
(ICON2 : address 003F
16)
Timer 1 interrupt enable bit
Timer 2 interrupt enable bit
Serial I/O reception interrupt enable bit
Serial I/O transmit interrupt enable bit
CNTR
0
interrupt enable bit
CNTR
1
interrupt enable bit
AD converter interrupt enable bit
Not used (returns “0” when read)
(Do not write “1” to this bit)
0 : Interrupts disabled
1 : Interrupts enabled
MITSUBISHI MICROCOMPUTERS
M37515M4-XXXHP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
TIMERS
The M37515M4-XXXHP has four timers: timer X, timer Y, timer 1,
and timer 2.
The division ratio of each timer or prescaler is given by 1/(n + 1),
where n is the value in the corresponding timer or prescaler latch.
All timers are count down. When the timer reaches “00
derflow occurs at the next count pulse and the corresponding
timer latch is reloaded into the timer and the count is continued.
When a timer underflows, the interrupt request bit corresponding
to that timer is set to “1”.
b7
b0
Timer XY mode register
(TM : address 0023
Timer X operating mode bit
b1b0
0 0: Timer mode
0 1: Pulse output mode
1 0: Event counter mode
1 1: Pulse width measurement mode
CNTR0 active edge selection bit
0: Interrupt at falling edge
Count at rising edge in event
counter mode
1: Interrupt at rising edge
Count at falling edge in event
counter mode
Timer X count stop bit
0: Count start
1: Count stop
Timer Y operating mode bit
b5b4
0 0: Timer mode
0 1: Pulse output mode
1 0: Event counter mode
1 1: Pulse width measurement mode
1 active edge selection bit
CNTR
0: Interrupt at falling edge
Count at rising edge in event
counter mode
1: Interrupt at rising edge
Count at falling edge in event
counter mode
Timer Y count stop bit
0: Count start
1: Count stop
Fig. 10 Structure of timer XY mode register
16”, an un-
16)
Timer 1 and Timer 2
The count source of prescaler 12 is the oscillation frequency
which is selected by timer 12 count source selection bit. The output of prescaler 12 is counted by timer 1 and timer 2, and a timer
underflow sets the interrupt request bit.
Timer X and Timer Y
Timer X and Timer Y can each select in one of four operating
modes by setting the timer XY mode register.
(1) Timer Mode
The timer counts the count source selected by Timer count source
selection bit.
(2) Pulse Output Mode
The timer counts the count source selected by Timer count source
selection bit. Whenever the contents of the timer reach “00
signal output from the CNTR
CNTR
0 (or CNTR1) active edge selection bit is “0”, output begins
0 (or CNTR1) pin is inverted. If the
16”, the
at “ H”.
If it is “1”, output starts at “L”. When using a timer in this mode, set
the corresponding port P2
7 ( or port P40) direction register to out-
put mode.
(3) Event Counter Mode
Operation in event counter mode is the same as in timer mode, except that the timer counts signals input through the CNTR
CNTR
1 pin.
When the CNTR
rising edge of the CNTR
When the CNTR
falling edge of the CNTR
0 (or CNTR1) active edge selection bit is “0”, the
0 (or CNTR1) pin is counted.
0 (or CNTR1) active edge selection bit is “1”, the
0 (or CNTR1) pin is counted.
0 or
(4) Pulse Width Measurement Mode
If the CNTR0 (or CNTR1) active edge selection bit is “0”, the timer
counts the selected signals by the count source selection bit while
the CNTR
tive edge selection bit is “1”, the timer counts it while the CNTR
(or CNTR1) pin is at “L”.
0 (or CNTR1) pin is at “H”. If the CNTR0 (or CNTR1) ac-
0
b7
b0
Timer count source selection register
(TCSS : address 0028
Timer X count source selection bit
IN
)/16 (f(X
0 : f(X
1 : f(XIN)/2 (f(X
Timer Y count source selection bit
0 : f(X
IN
)/16 (f(X
1 : f(XIN)/2 (f(X
Timer 12 count source selection bit
0 : f(X
IN
)/16 (f(X
1 : f(X
CIN
)
Not used (returns “0” when read)
16
CIN
)/16 at low-speed mode)
CIN
)/2 at low-speed mode)
CIN
)/16 at low-speed mode)
CIN
)/2 at low-speed mode)
CIN
)/16 at low-speed mode)
)
Fig. 11 Structure of timer count source selection register
The count can be stopped by setting “1” to the timer X (or timer Y)
count stop bit in any mode. The corresponding interrupt request
bit is set each time a timer underflows.
■Note
When switching the count source by the timer 12, X and Y count
source bit, the value of timer count is altered in unconsiderable
amount owing to generating of a thin pulses in the count input
signals.
Therefore, select the timer count source before set the value to
the prescaler and the timer.
13
Data bus
MITSUBISHI MICROCOMPUTERS
M37515M4-XXXHP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
f(XIN)/16
f(XIN)/2
Timer X count source selection bit
7/CNTR0
P2
7
Port P2
direction register
f(XIN)/16
f(XIN)/2
Timer Y count source selection bit
P40/CNTR1
Port P4
direction register
CNTR
edge selection
“0”
“1”
Port P2
latch
Pulse output mode
CNTR
edge selection
“0”
“1”
Port P4
0
Pulse output mode
latch
0 active
bit
7
1 active
bit
0
Pulse width
measurement
mode
Event
counter
mode
CNTR
edge selection
bit
Pulse width
measurement mode
Event
counter
mode
CNTR1 active
edge selection
bit
Timer mode
Pulse output mode
Timer X count stop bit
0 active
“1”
“0”
Timer mode
Pulse output mode
Timer Y count stop bit
“1”
“0”
Data bus
Prescaler X latch (8)
Prescaler X (8)
Q
Toggle flip-flop
Q
R
Data bus
Prescaler Y latch (8)
Prescaler Y (8)
Q
Toggle flip-flop
Q
R
Timer X latch (8)
Timer X (8)
T
Timer X latch write pulse
Pulse output mode
Timer Y latch (8)
Timer Y (8)
T
Timer Y latch write pulse
Pulse output mode
To timer X interrupt
request bit
To CNTR
0 interrupt
request bit
To timer Y interrupt
request bit
To CNTR
1 interrupt
request bit
Prescaler 12 latch (8)
f(XIN)/16
f(XCIN)
Timer 12 count source selection bit
Prescaler 12 (8)
Fig. 12 Block diagram of timer X, timer Y, timer 1, and timer 2
14
Timer 1 latch (8)
Timer 1 (8)
Timer 2 latch (8)
Timer 2 (8)
To timer 2 interrupt
request bit
To timer 1 interrupt
request bit
MITSUBISHI MICROCOMPUTERS
M37515M4-XXXHP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
SERIAL I/O
Serial I/O can be used as either clock synchronous or asynchronous (UART) serial I/O. A dedicated timer is also provided for baud
rate generation.
Data bus
Address 0018
Transmit shift register
Transmit buffer register
Data bus
P24/RXD
P26/SCLK
P2
7/SRDY
P2
5/TXD
XIN
Receive buffer register
Receive shift register
BRG count source selection bit
1/4
F/F
Falling-edge detector
(1) Clock Synchronous Serial I/O Mode
Clock synchronous serial I/O mode can be selected by setting the
serial I/O mode selection bit of the serial I/O control register (bit 6
of address 001A
For clock synchronous serial I/O, the transmitter and the receiver
must use the same clock. If an internal clock is used, transfer is
started by a write signal to the TB/RB.
16
Shift clock
Serial I/O synchronous
clock selection bit
Frequency division ratio 1/(n+1)
Baud rate generator
Address 001C
Shift clock
Address 0018
Clock control circuit
16
Clock control circuit
16
16) to “1”.
Serial I/O control register
Receive buffer full flag (RBF)
Receive interrupt request (RI)
1/4
Transmit interrupt source selection bit
Serial I/O status register
Address 001A16
Transmit shift completion flag (TSC)
Transmit interrupt request (TI)
Transmit buffer empty flag (TBE)
Address 0019
16
Fig. 13 Block diagram of clock synchronous serial I/O
Transfer shift clock
(1/2 to 1/2048 of the internal
clock, or an external clock)
Serial output TxD
Serial input RxD
Receive enable signal S
RDY
D
0
D
0
Write pulse to receive/transmit
buffer register (address 0018
16
)
TBE = 0
TBE = 1
TSC = 0
1: As the transmit interrupt (TI), either when the transmit buffer has emptied (TBE=1) or after the transmit shift operation has
Notes
ended (TSC=1), by setting the transmit interrupt source selection bit (TIC) of the serial I/O control register.
2: If data is written to the transmit buffer register when TSC=0, the transmit clock is generated continuously and serial data
is output continuously from the TxD pin.
3: The receive interrupt (RI) is set when the receive buffer full flag (RBF) becomes “1” .
Fig. 14 Operation of clock synchronous serial I/O function
D
D
1
D
2
D
1
D
2
D
3
D
3
D
4
D
4
D
5
D
5
D
6
D
6
7
D
7
RBF = 1
TSC = 1
Overrun error (OE)
detection
15
MITSUBISHI MICROCOMPUTERS
M37515M4-XXXHP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(2) Asynchronous Serial I/O (UART) Mode
Clock asynchronous serial I/O mode (UART) can be selected by
clearing the serial I/O mode selection bit (b6) of the serial I/O control register to “0”.
Eight serial data transfer formats can be selected, and the transfer
formats used by a transmitter and receiver must be identical.
The transmit and receive shift registers each have a buffer, but the
Data bus
P2
P2
P2
4/RX
6/SCLK1
X
5/TX
D
ST detector
BRG count source selection bit
IN
D
Character length selection bit
1/4
Character length selection bit
Address 0018
OE
7 bits
8 bits
Serial I/O synchronous clock selection bit
16
Receive buffer register
Receive shift register
PE FE
SP detector
Frequency division ratio 1/(n+1)
Baud rate generator
Address 001C
ST/SP/PA generator
Transmit shift register
Transmit buffer register
Data bus
two buffers have the same address in memory. Since the shift register cannot be written to or read from directly, transmit data is
written to the transmit buffer register, and receive data is read from
the receive buffer register.
The transmit buffer register can also hold the next data to be
transmitted, and the receive buffer register can hold a character
while the next character is being received.
Serial I/O control register
Receive buffer full flag (RBF)
Receive interrupt request (RI)
Clock control circuit
16
1/16
Transmit interrupt source selection bit
0018
Address
16
Address 001A
1/16
UART control register
Transmit shift completion flag (TSC)
Transmit interrupt request (TI)
Transmit buffer empty flag (TBE)
Serial I/O status register
16
Address 001B
Address
0019
16
16
Fig.15 Block diagram of UART serial I/O
16
Transmit or receive clock
MITSUBISHI MICROCOMPUTERS
M37515M4-XXXHP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Transmit buffer write
Receive buffer read
signal
TBE=0 TBE=0
TSC=0
TBE=1
Serial output TXD
signal
Serial input R
Notes
X
D
1: Error flag detection occurs at the same time that the RBF flag becomes “1” (at 1st stop bit, during reception).
2: As the transmit interrupt (TI), when either the TBE or TSC flag becomes “1,” can be selected to occur depending on the setting of the transmit
interrupt source selection bit (TIC) of the serial I/O control register.
3: The receive interrupt (RI) is set when the RBF flag becomes “1.”
4: After data is written to the transmit buffer when TSC=1, 0.5 to 1.5 cycles of the data shift cycle is necessary until changing to TSC=0.
ST
0
D
1
1 start bit
7 or 8 data bit
1 or 0 parity bit
1 or 2 stop bit (s)
ST
0
D
1
Fig. 16 Operation of UART serial I/O function
[Transmit Buffer Register/Receive Buffer
Register (TB/RB)] 0018
The transmit buffer register and the receive buffer register are located at the same address. The transmit buffer is write-only and
the receive buffer is read-only. If a character bit length is 7 bits, the
MSB of data stored in the receive buffer is “0”.
16
[Serial I/O Status Register (SIOSTS)] 001916
The read-only serial I/O status register consists of seven flags
(bits 0 to 6) which indicate the operating status of the serial I/O
function and various errors.
Three of the flags (bits 4 to 6) are valid only in UART mode.
The receive buffer full flag (bit 1) is cleared to “0” when the receive
buffer register is read.
If there is an error, it is detected at the same time that data is
transferred from the receive shift register to the receive buffer register, and the receive buffer full flag is set. A write to the serial I/O
status register clears all the error flags OE, PE, FE, and SE (bit 3
to bit 6, respectively). Writing “0” to the serial I/O enable bit SIOE
(bit 7 of the serial I/O control register) also clears all the status
flags, including the error flags.
Bits 0 to 6 of the serial I/O status register are initialized to “0” at reset, but if the transmit enable bit (bit 4) of the serial I/O control
register has been set to “1”, the transmit shift completion flag (bit
2) and the transmit buffer empty flag (bit 0) become “1”.
TBE=1
STD
SP
RBF=1
STD
SP D
D
0
D
1
Generated at 2nd bit in 2-stop-bit mode
RBF=0
0
D
1
TSC=1
SP
RBF=1
SP
Serial I/O Control Register (SIOCON)] 001A16
The serial I/O control register consists of eight control bits for the
serial I/O function.
[UART Control Register (UARTCON)] 001B16
The UART control register consists of four control bits (bits 0 to 3)
which are valid when asynchronous serial I/O is selected and set
the data format of an data transfer and one bit (bit 4) which is always valid and sets the output structure of the P2
5/TXD pin.
[Baud Rate Generator (BRG)] 001C16
The baud rate generator determines the baud rate for serial transfer.
The baud rate generator divides the frequency of the count source
by 1/(n + 1), where n is the value written to the baud rate generator.
■Note
When using the serial I/O, clear the I2C-BUS interface enable bit
to “0” or the S
CL/SDA interrupt pin selection bit to “0”.
17
Loading...