Mitsubishi L75-A81, L75-A91 User Guide

Download

MODEL

L75–A81

Owner’s Guide

MODEL

L75–A91

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilat-

eral triangle is intended to alert the user to

the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

MAINS DISCONNECTION: The mains plug is used as the disconnect device. The mains plug shall remain readily operable.

WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

This apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

Cet appareil ne doit pas être exposé à des gouttes ou à des éclaboussures et aucun objet rempli d’un liquide, comme un vase, ne doit être placé sur l’appareil.

WARNING: This product contains chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm.

TV WEIGHT: This TV is heavy. Exercise extreme care when lifting or moving it. Lift or move the TV with a minimum of two adults. To prevent damage to the TV, avoid jarring or moving it while it is turned on. Always power off your TV, unplug the power cord, and disconnect all cables before moving it.

Stand Requirement

Mitsubishi does not design, manufacture or sell matching bases for L75-A81 and L75-A91 model televisions. When selecting a stand, base, or other furniture to support the TV, please make sure it is designed with the appropriate dimensions for stability and to support the TV’s weight plus the weight of any additional equipment you plan to store.

Children and Television Viewing

The American Academy of Pediatrics discourages television viewing for children younger than two years of age.

FCC Declaration of Conformity

Product: Projection Television Receiver Models: L75-A81, L75-A91 Responsible

Party:

Telephone: (800) 332-2119

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and

(2) This device must accept any interference

received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equip- -

ment and the receiver. Connect the equipment into an outlet on -

a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/ -

TV technician for help.

Changes or modifications not expressly approved by Mitsubishi could cause harmful interference and would void the user’s authority to operate this equipment.

Mitsubishi Digital Electronics America, Inc. 9351 Jeronimo Road Irvine, CA 92618-1904

Canadian Notice

For Model L75-A81

This Class B digital apparatus complies with

Canadian ICES-003.

Note: Features and specifications described in this owner’s guide are subject to change without notice.

In the U.S. call 1(877) 675-2224 for assistance.

AN TE NN A LE AD IN W IR E

AN TE NN A DIS C HA R G E UNI T (N E C AR T IC LE 8 10-20 )

G R OU NDI NG C OND UC TO R S (N E C AR T IC LE 8 10-21 )

G R OU ND CL AMP S

P OW E R S E R VIC E G R OUN DING E LE C TR O DE S YS T E M (N E C AR T 2 50, PA R T H)

G R OU ND CL AMP

E LE C TR IC S E R V ICE E QU IPM EN T

NE C — N AT IO NAL E LE C TR IC AL C ODE

E XA MP LE O F AN T E N NA G R OU N DIN G

Important Safety Instructions

Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges.

Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

In Canada call 1(800) 450-6487 for assistance.

CAUTION CLASS 4 LASER LIGHT WHEN OPEN AVOID EYE OR SKIN EXPOSURE TO DIRECT OR SCATTERED RADIAITON

ATTENTION LUMIÈRE LASER DE CLASSE 4 - EN CAS D’OUVERTURE EXPOSITION DANGEREUSE AU RAYONNEMENT DIRECT OU DIFFUS DES YEUX OU DE LA PEAU

Laser Safety

This TV is in compliance with the requirements of IEC • 60825-1 Ed. 2(2007).

This TV is a CLASS 1 laser product. This TV poses • no risk to eyes or skin during normal use. An exposure hazard may exist only if the protective housing is removed.

This TV contains a CLASS 4 laser device, which by • itself may be hazardous. However, this TV incorporates a protective housing, optics and electronics such that there should be no exposure to unsafe levels of laser light during normal operation and proper service.

Do not open this product. No consumer controls • inside. Only a trained LASERVUE® technician should service this TV. Please call Mitsubishi for assistance.

In the U.S.A. call 1-877-675-2224. In Canada call 1-800-450-6487. -

This label is located on the right lower back of the television set.

Safe Operation

Always inspect the TV for damage after moving it. • If the cabinet or screen is physically damaged, DO NOT connect the TV to an AC outlet.

In the U.S.A. call 1-877-675-2224 for assistance. In Canada call 1-800-450-6487. -

DO NOT power on the TV until it has been repaired by qualified service personnel authorized by Mitsubishi. See “Service” on the next page.

Caution.• Use of controls or adjustments or per- formance of procedures other than those specified herein may result in hazardous radiation exposure.

Use external or remote controls to operate the • product. Connection to signal sources and power are accomplished through the external connectors.

Damage and Repair

There are no user serviceable components in this • TV. Do not attempt to disassemble any part of the TV.

If damaged, the device must not be powered on or • used until it is repaired by qualified service personnel authorized by Mitsubishi. See “Service” on the next page.

Under no circumstances shall attempts be made to • operate this device without the screen in place or if any portion of the enclosure, including the screen, is cracked, broken, a liquid is spilled onto the TV or is otherwise damaged.

This class-4 label and similar service warning labels are located inside the back cover of the television in an area that should not be accessed by the user under any circumstances.

An additional class-4 label is located at the lower front access panel under the front decorative bezel.

This class-4 label is located at the center back of the TV under the outer cover.

In the U.S. call 1(877) 675-2224 for assistance.

For Your Records

Record the model number, serial number, and purchase date of your TV. The model and serial numbers are on the back of the TV. Refer to this page when requesting assistance with the TV.

MODEL NUMBER

SERIAL NUMBER

PURCHASE DATE

RETAILER NAME

LOCATION

Installation and Operating Notes

Custom cabinet installation must allow for proper air circulation around the television.

NOTE TO CATV SYSTEM INSTALLER: THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR THE PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL.

TV Software

Do not attempt to update the software of this TV with software or USB drives not provided by or authorized by Mitsubishi Digital Electronics America, Inc. (U.S.A.) or Mitsubishi Electric Sales Canada Inc. Non-authorized software may damage the TV and will not be covered by the warranty.

Internal Fans

Internal cooling fans maintain proper operating temperatures inside the TV. It is normal to hear the fans when you first turn on the TV and during quiet scenes while viewing the TV.

For Questions:

U.S.A. www.mitsubishi-tv.com

MDEAservice@mdea.com 877-675-2224

Service

If you are unable to correct a problem with your TV:

U.S.A.

877-675-2224

DO NOT adjust any controls other than those described in this Owner’s Guide.• DO NOT remove the protective back cover of your TV.•

Customer Support

This Owner’s Guide is available in electronic format at www.mitsubishi-tv.com.• To order replacement or additional remote controls, Owner’s Guides, or NetCommand IR emitters:•

U.S.A. www.mitsuparts.com

800-553-7278

Canada www.MitsubishiElectric.ca

support@MitsubishiElectric.ca 800-450-6487

Canada 800-450-6487

Canada www.MitsubishiElectric.ca

800-450-6487

In Canada call 1(800) 450-6487 for assistance.

Contents

Important Information About Your TV

Important Safety Instructions ................ 2

Laser Safety ........................... 3

Installation and Operating Notes ............. 4

1 Basic Setup and Operation

Package Contents ....................... 6

Special Features of Your TV................. 7

TV Controls and Indicators ................. 8

First-Time Power-On ..................... 11

Setting Up TV Inputs..................... 12

Basic TV Operation...................... 14

Using the TV with a Personal Computer ....... 16

2 TV Connections

Before You Begin ....................... 18

Cable Management ..................... 18

Inputs and Outputs ...................... 19

Y Pb Pr Component Video Device ........... 21

DMI Device .............................21

DVI Video Device ....................... 22

Antenna or Cable TV Service ............... 22

Composite Video Device .................. 22

VCR or DVD Recorder to an Antenna or

Wall Outlet Cable ...................... 23

VCR or DVD Recorder to a Cable Box ........ 23

A/V Receiver .......................... 24

A/V Receiver with HDMI Output ............. 24

3 Using TV Features

Selecting an Input ...................... 25

Sleep Timer ........................... 25

ChannelView Channel Listings .............. 26

Redirecting Audio Output ................. 26

Controlling A/V Receiver Sound Volume ....... 26

Status Display ......................... 27

TV Signals and Display Formats ............. 28

3D Video ............................. 29

Camera and Music Files .................. 31

Streaming Internet Movies with VUDU ........ 34

Introduction to Home-Theater Control ........ 36

4 TV Menus

Main Menu ............................ 37

Menu Navigation ....................... 37

Adjust ............................... 38

Captions ............................. 42

Initial ................................ 43

Inputs ............................... 45

Lock ................................ 47

5 NetCommand IR Control

About NetCommand IR Control ............. 50

IR Emitter Placement .................... 51

Initial NetCommand Setup ................ 52

Operating NetCommand-Controlled Devices ... 53

6 NetCommand IR Control of an A/V Receiver

Controlling an A/V Receiver after

NetCommand Setup .................... 56

Setting Up A/V Receiver Control

Power and Volume ................... 57

Automatic Audio or Audio/Video Switching . . 58

Appendices

Appendix A: Programming the Remote Control . 64

Appendix B: Bypassing the Parental Lock ..... 71

Appendix C: HDMI Control of CEC Devices .... 73

Appendix D: TV Care .................... 76

Appendix E: Troubleshooting .............. 77

Trademark and License Information .......... 84

Mitsubishi TV Software .................... 85

Warranty .............................. 88

Index ................................. 92

In the U.S. call 1(877) 675-2224 for assistance.

Emitter bulb

GUIDE MENU INFO BACK

ACTIVITY

Basic Setup and Operation

Package Contents

Please take a moment to review the following list of items to ensure that you have received everything.

Remote Control1.

Two AA Batteries2.

Owner’s Guide3.

Remote Control Batteries

Remove the remote control back cover.1.

Load the batteries, making sure the polarities 2. (+) and (-) are correct. Insert the negative (-) end first.

Quick Setup Guide4.

Product Registra-5. tion Card

Cable Tie6.

L75-A91: Four-ended 7. IR emitter cable

Slide the cover back into place.3.

In Canada call 1(800) 450-6487 for assistance.

1. Basic Setup and Operation 7

Special Features of Your TV

Welcome to LASERVUE® TV! Mitsubishi has created a new category of television with laser technology. Laser beams provide the widest range of rich, complex colors, along with the most clarity and depth of field. Precise and focused, the purity of laser light far surpasses current high-definition technologies and sets a new standard for premium large-screen television.

Your new high-definition widescreen television has

many special features that make it the perfect center of your home entertainment system, including:

1080p High-Definition DLP Display System

Your Mitsubishi HDTV uses Texas Instruments Digital

Light Processing™ technology for rear-projection TVs to create the picture you see on screen. All images are displayed at 1080p. The TV uses Plush 1080p® 5G to convert lower-resolution signals to 1080p for display.

The TV can also accept 1080p original signals and main-

tain them at 1080p through all processing until displayed.

3D Ready

All Mitsubishi 1080p LASERVUE HDTV’s are 3D Ready. This feature lets you experience the new 3D technolo-

gies applied to many recent movies and video games. Immerse yourself in your favorite video game, movie, or sporting event displayed in 3D.

Easy Connect Auto Input Sensing

Easy Connect™ Auto Input Sensing automatically recognizes when you plug in a device and prompts you to assign a name to it. The TV ignores any unused inputs, so the result is an uncluttered menu where you can easily find and select connected devices by name.

Home-Theater Control

HDMI Control

HDMI devices with Consumer Electronics Control (CEC) capabilities may be compatible with the TV’s HDMI Control feature. Compatible devices can receive control signals through the HDMI connection, allowing the TV’s remote control to operate some functions of these devices.

NetCommand with IR Learning

Model L75-A91. Your Mitsubishi HDTV offers a new level of networking that seamlessly integrates selected older A/V products with new and future digital products. NetCommand® supports IR (infrared) control of products such as VCRs, DVD players, cable boxes, and satellite receivers. NetCommand can “learn” remote control signals directly from many devices, allowing you to create a customized NetCommand-controlled hometheater system.

Integrated HDTV Tuner

Your widescreen Mitsubishi LASERVUE HDTV has an

internal HDTV tuner able to receive both over-the-air HDTV broadcasts (received via an antenna) and nonscrambled digital cable broadcasts, including nonscrambled HDTV cable programming.

High-Definition Video Inputs

Component Video Inputs.• Also called Y/Pb/Pr

inputs, these inputs receive standard analog video

formats of 480i, 480p, plus 720p and 1080i high-

definition signals. This provides a high level of

flexibility when connecting DVD players/recorders,

cable boxes, and satellite receivers.

HDMI Inputs.• These inputs accept digital 480i,

480p, 720p, 1080i, and 1080p video signals plus

PCM digital stereo signals. The HDMI™ inputs can

also accept a variety of PC signals and resolutions.

These inputs support HDMI 1.3 Deep Color (up to

36 bits) and the x.v.Color extended color gamut.

Used with an adapter, these HDMI inputs also

accept compatible digital DVI video signals. HDMI

inputs provide additional high-performance,

high-definition connections for maximum flexibility

in your choice of home theater products. The HDMI

inputs are HDCP copy-protection compatible.

Internet-Video Ready

Model L75-A91. Built-in VUDU™ connectivity lets you

stream high-definition internet video content directly to your TV. Access to VUDU’s fee-based movie service is through menus displayed on the TV. largest on-demand HD movie selection anywhere, featuring full 1080p and 5.1 surround sound. VUDU allows you to enjoy movies with no store visits, no mailing, no late fees and no subscriptions.

ENERGY STAR

This is an ENERGY STAR® qualified TV. Products that

earn the ENERGY STAR prevent greenhouse gas emissions by meeting strict energy efficiency guidelines set by the U.S. Environmental Protection Agency and the U.S. Department of Energy.

This TV consumes energy in excess of ENERGY STAR

guidelines for a powered-down device under the following conditions:

Model TV Condition

L75-A81 L75-A91

L75-A91 TV powered off, External Controller Input

TV powered off, Fast Power On mode

enabled

VUDU offers the

In the U.S. call 1(877) 675-2224 for assistance.

8 1. Basic Setup and Operation

F3 F4F2

FAV

DEMAND

GUIDE

INFO

BACK

ACTIVITY

TV Controls and Indicators

Remote Control

Press to select a TV activity and input.

See page 25.

GUIDE

ChannelView listings, page 26

TV main menu, page 37

INFO

TV status (

Steps back one menu; clears

BACK

the top menu or Status Display.

page 27)

or TV help.

VOLUME UP

VOLUME DOWN

Record/Playback controls for external devices When remote control is programmed, page 64

HDMI control, page 75

L75-A91: NetCommand, page 55

(

PAUSE) Freezes a broadcast TV picture.

L75-A91. See page 64.

Number/letter keys

Channel tuning, page 14

Adds a separator when entering digital

channel numbers. Clears some menu entries.

L75-A91. See page 64.

MUTE

VCR CA B L /SAT TV DVD AUDIO

Control-mode indicator for device type to control. Use the side button to change.

Powers TV on or off

Side button sets the control mode for the type of device to operate. Set mode to TV for normal TV viewing.

CHANNEL UP

LAST.

Returns to the previously tuned

channel.

CHANNEL DOWN

PAGE UP

ENTER

Selects a channel number or menu item.

Navigation controls

PAGE DOWN

Displays a menu showing additional functions for the number keys.

For the •

menu in TV mode, see below. With remote control programmed • for another device, the

is specific to the device. See page

64. For CEC-enabled devices, • page 75

Note: To operate other audio/video

devices using the TV’s remote control:

• SeeAppendix A, “Programming the Remote Control.”

• ForHDMIdevicescompatiblewiththeTV’s

HDMI Control feature, see Appendix C.

• L75-A91. With NetCommand

See - page 50 for NetCommand IR “Learn-

ing” of device keys.

For use of specific keys with NetCom- -

mand-controlled devices, see “Special Operation Methods,” page 53.

In Canada call 1(800) 450-6487 for assistance.

Closed captions, page 42

VIDEO

Video adjustments, page 38

AUDIO

Audio adjustments, page 39

SLEEP FO R M AT MORE

The MORE menu in TV mode

Sleep Timer, page 25 Picture shape (aspect ratio), page 28 Clears

the MORE menu.

1. Basic Setup and Operation 9

TV Controls and Indicators, continued

TV Control Panel

Buttons on the control panel duplicate some keys on the remote control.

Refer to • left labels when no TV menus are dis- played.

Refer to • right labels when using TV menus or after activating a special function.

System Reset

If the TV fails to respond to the remote control, the control-panel buttons, or will not power on/off, perform System Reset. Recent setting changes made before using System Reset may be lost.

To perform System Reset, press and hold the button on the control panel for ten seconds.

Panel-Lock Release

To • release the Panel Lock using the TV control panel, press and hold the control panel for ten seconds. If the TV is off, press the

POWER

button to make it power on. To activate the Panel Lock, use the • Lock menu, page 49.

ACTIVITY

button on the

POWER

In the U.S. call 1(877) 675-2224 for assistance.

10 1. Basic Setup and Operation

POWER

TV Controls and Indicators, continued

POWER Indicator

Key

Off

Steady On Slow Blinking Fast Blinking

LED Color TV Condition Additional Information

None

Green

Yellow

Red

TV is powered off. Normal operation.

TV is powered on. Normal operation.

TV powered off, auto-on TV Timer is set. Normal operation. TV can be turned on at any time.

TV power just turned on. Normal operation. A picture will appear shortly.

TV just plugged into AC outlet.• AC just restored after power failure.• TV is rebooting after power fluctua-•

tion or receiving abnormal digital signals from a digital channel or digital device.

You have begun the procedure to • update software from an authorized flash memory device.

TV is too hot.

TV may require service.

Wait approximately two minutes for blinking to stop before turning on. Normal operation.

The TV will display a warning message and shut off if it overheats.

• Ambientroomtemperaturemaybetoohigh.Turnoff

the TV and let the room temperature drop.

• Clearblockedairvents.Ensureatleastafour-inch

clearance on all sides of the TV.

Turn off the TV and unplug the set from the AC power source. Wait one minute and then plug the set back in. See Appendix E.

If the LED is still on, contact Mitsubishi to receive Authorized Service Center information:

U.S.A. Go to www.mitsubishi-tv.com or call 1-877-675-2224. Canada. Go to www.MitsubishiElectric.ca or call

1-800-450-6487.

In Canada call 1(800) 450-6487 for assistance.

1. Basic Setup and Operation 11

GUIDE MENU INFO BACK

First-Time Power-On

Before You Begin

Review the important safety, installation, and oper-

ating information at the beginning of this book. Choose a location for your TV.

• Allowatleastfourinchesofspaceonallsides

of the TV to help prevent overheating. Overheating may cause premature failure of the TV.

• Avoidlocationswherelightmayreflectoffthe

screen.

• Seethestandrequirementsonpage 1.

Install the batteries in the remote control.

Plug the TV into an AC power outlet.

TV Tips

Turning the TV On or Off

Point the remote control at the front of the TV • and press the Press the • panel.

Controlling Sound Volume

Press •

VOLUME UP/VOLUME DN

level from the TV speakers. See also • “Controlling A/V Receiver Sound Volume” on page 26.

POWER

button.

POWER

button on the TV control

to adjust the sound

Power-On

Confirm that the remote

control is in TV mode.

Press the side button • once to light the mode indicator and confirm that TV mode is active. To change, press the • side button additional times to activate TV mode.

Aim the remote control

at the TV and press the

POWER

key . Wait for the

Welcome screen.

Press

change the menu language to Español.

Press

Home/Retail selections. Here you can choose a picture mode suited to your viewing conditions.

if you wish to

to move to the

Mitsubishi recommends the • Home setting. The Home setting selects the Brilliant Picture Mode.

The • Retail setting selects the Super Brilliant Picture Mode. The Super Brilliant Picture Mode is designed to compensate for the harsh, bright lighting used in retail settings and is not recommended for home use. Prolonged use of the Super Brilliant Picture Mode will age the lasers faster, reducing picture brightness as the TV ages.

For more on Picture Modes, see • page 38.

Press

Press menu.

to highlight EXIT.

ENTER

to clear the

In the U.S. call 1(877) 675-2224 for assistance.

12 1. Basic Setup and Operation

Setting Up TV Inputs

Using the ANT (Antenna) Input

If using an antenna or direct cable service (no cable box), connect the incoming coaxial cable to the TV’s

ANT

input. Refer to page 22.

You must save channels to memory with a channel scan to enable reception of all available high-definition and standard-definition digital channels. The channel scan will search for channels available locally. If you skip this step, the TV can receive only analog channels.

Memorizing Channels with Channel Scan

For the ANT input

To start channel memorization

Power on the TV.

Press

Start channel memorization from the Initial > Channel menu.

and open the Initial > Channel menu.

Setting Up Other Inputs

Connect your devices to the TV, making note of

which TV input jack is used for each device. See “TV Connections,” page 18, for recommendations.

Power on the devices to ensure detection.

Power on the TV.

The TV will display the New Device Found screen for each new connection it detects Learn more about Auto Input/Auto Output Sensing on the opposite page.

Select the device type from the list on screen.

Press

To stop channel memorization before completion, press

Use the Initial > Channel > Edit menu (page 44) for additional channel options, such as adding or deleting channels from memory.

ENTER

to enter the menu.

Select over-the-air antenna. Select Ant Cable for direct cable.

Highlight Channel memorization may take up to 15 minutes to complete.

Ant Air if connected to an

Scan and press

CANCEL

ENTER

Sample New Device Found screen.

Important Note for NetCommand IR Users L75-A91. Be sure to select the correct device type

here. Although you can change the device type later in the Inputs > Name menu, any “learned” NetCommand IR codes will be erased when you make the change.

L75-A91.

ing” after selecting the device type or at a later time when convenient. To perform now, highlight NetCommand and press NetCommand Setup,” page 52 or “Setting Up A/V Receiver Control,” page 57.

Press

The TV will then display the New Device Found screen for the next connection it finds.

You can perform NetCommand IR “learn-

ENTER

. See

“Initial

BACK

to close the New Device Found screen.

In Canada call 1(800) 450-6487 for assistance.

1. Basic Setup and Operation 13

Setting Up TV Inputs, continued

About Auto Sensing

This TV’s Easy Connect™ Auto Sensing feature detects most connections automatically. The exceptions are:

A connection on the • An HDMI device that is powered off. Power on • the device to ensure detection.

Auto Input/Auto Output Sensing for Most Devices

When you first connect a device, the TV will:

a. Detect the connected device and automati-

cally switch to it. b. Prompt you to identify the device type. c. L75-A91. Prompt you to perform NetCom-

mand set-up for the device, if available. d. Repeat these steps for other newly detected

devices.

When You First Connect a Device

Most Device Types.• Select the device type from

the on-screen list. The device type you select here will appear as a device icon in the menu.

A/V Receiver•

T -

he TV can detect audio connections on the

DIGITAL AUDIO OUTPUT

right (red)

For an HDMI A/V receiver, select - AVR from

the list of device types if the A/V receiver is

not recognized automatically.

HDMI CEC Devices Compatible with the TV’s • HDMI Control Feature.

enabled HDMI devices are often recognized automatically by the TV. to control some functions of a CEC-enabled device. See Appendix C, “HDMI Control of CEC Devices.”

ANT

input

jack (orange) and the

AVR AUDIO OUTPUT

Compatible CEC-

HDMI Control may allow you

jack.

Activity

New Device Found screen for a device with HDMI control enabled. Select On to enable the TV’s CEC control of the device. In some cases, as in the example above, you will also be prompted to select a device name.

Tips on Auto Sensing

Choose a different name for each input.• The antenna input (• although you can turn off the unused antenna input in the Inputs > Name menu. Change the device type displayed in the • Activity menu by using the Inputs > Name menu (page

45). L75-A91.• Any “learned” NetCommand IR codes will be erased if you change the device type in the Inputs > Name menu.

Reactivating Auto Input Sensing for an HDMI Input

When you disconnect an HDMI device, Auto Input Sensing is disabled until you perform these steps.

Disconnect the HDMI device.

Delete the removed HDMI device in the

Name menu (see “Removing an HDMI Device,”

page 75). Connect the new device and the

Found screen will display.

ANT

) is never detected,

New Device

Inputs >

In the U.S. call 1(877) 675-2224 for assistance.

14 1. Basic Setup and Operation

Basic TV Operation

Selecting an Input to Watch

Press

Press Press

ACTIVITY

ENTER

and to highlight an input.

to switch to the input.

Watching Broadcast TV

TV Connected to an Antenna, Direct Cable, Cable

Box, Set-Top Box, or Satellite Receiver

Press

Note: For more about the Activity menu, see page 25.

ACTIVITY

Press you named devices during Auto Input Sensing, select an input from the Watch TV group. Note:

Your TV may have only one group (Watch TV).

and to select a broadcast source. If

Watching DVDs or Videos

TV Connected to a DVD Player, DVR, or VCR

Press

ACTIVITY

Activity menu. If you named devices during Auto Input Sensing, select the input from the Watch Movie group.

Activity menu, DVD input selected

and select a movie source from the

Activity menu, antenna input selected

Tune to a channel on the

3. ANT

these methods.

Enter the channel number using the number • keys on the remote control and press

For a two-part digital channel, such as 3-1, press 3

Press • channels one channel at a time.

Press • ously tuned channel.

Antenna or Direct Cable Only.• Press display ChannelView channel listings, highlight a channel number, and press

Note: Program information is provided by broadcasters and may not be available in all areas.

—

CANCEL

CHANNEL UP /CHANNEL DN (+/–

1 to enter a dash (separator).

(LAST)

to switch back to the previ-

input using any of

) to change

ENTER

to tune.

ENTER

GUIDE

In Canada call 1(800) 450-6487 for assistance.

1. Basic Setup and Operation 15

Basic TV Operation, continued

Making Picture Adjustments

To get the best picture under different viewing con-

ditions, set the Picture Mode before changing other video settings. See page 38 for more.

a. Press b. Press 8 (VIDEO). c. Press to make one of these Picture Mode

Press

ment you want. Press

Additional picture adjustments are described on pages 40 and 41.

MORE.

selections:

Name When to Use

Super Brilliant

Brilliant

Game

Bright For most daytime viewing

Natural For most nighttime viewing

Cinema For recreating theater colors

to display the name of the next adjust-

to make the adjustment.

Under harsh retail lighting; not recommended for home use

Under bright light

With gaming consoles

Audio Settings

Changing the Audio Output

To switch audio output from the internal TV speakers to a connected external sound system or headphones:

Other TV Features

Activate Audio Lock to control your sound system • with the TV’s remote control left in TV mode. See page 65.

To set the TV Clock see • page 43. Set the TV Clock if you plan to use the TV Timer (page 43) or ChannelView (page 26) features.

To set parental controls, see the • Lock menu, page

47. Note: L75-A91. To set parental controls for

VUDU™ service, use the VUDU Info & Settings menu.

To change the input names that appear in the • Activity menu, see Inputs > Name options, page

45. 3D Video.• See page 29. To program the remote control to operate other •

A/V devices, see Appendix A, “Programming the Remote Control,” page 64.

To control compatible devices using HDMI CEC • control, see Appendix C, “HDMI Control of CEC Devices,” page 73.

To view still and moving digital camera images on • the TV, see “Camera and Music Files,” page 31.

L75-A91.• To control A/V devices with NetCom- mand, see chapter 5, “NetCommand IR Control for Most Devices” on (page 50).

L75-A91.• See page 34 for internet video streaming with VUDU™.

Other Information

Press

Changing Audio Settings

Press

(AUDIO).

Press The Speakers option will display only if a connec- tion has been detected on one of the TV’s audio outputs.

Press Receiver or Headphones.

Press Press Press

you want. Press

until the Speakers option is displayed.

to switch between TV and either AV

(AUDIO).

to display the name of the adjustment

to change the setting.

TV Care

Remote Control.• See “Care of the Remote Control” on page 76

General Cleaning.• See “Cleaning Recommenda- tions,” page 76.

Assistance

For basic troubleshooting, see • Appendix E, page

77. For service, and product support, see • page 4. For warranty information, see the TV warranty on •

page 88.

In the U.S. call 1(877) 675-2224 for assistance.

16 1. Basic Setup and Operation

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

Computer with HDMI output

panel

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

DVI/PC

INPUT

DVI/PC

INPUT

DVI

OUT

AUDIO

Computer with DVI and analog stereo outputs

Using the TV with a Personal Computer

Connecting a Computer to the TV

Use one of the connection methods listed below based on your computer’s video output.

Computer Video Output

Video Connection

Digital DVI DVI-to-HDMI cable

or an HDMI cable

Audio

Connection

Stereo audio

cables with an HDMI-toDVI adapter

Note: If the computer’s audio output is a single mini jack, a mini audio-toRCA-male “Y” adapter cable is also required.

HDMI HDMI-to-HDMI

cable

No additional

audio connec-

tion is required.

IMPORTAN T

This TV accepts digital computer signals only.

Connect the computer’s digital signal output to one

of the TV’s

HDMI

jacks. See the connection dia-

grams for the method suited to your equipment. Connect the computer’s audio output using one of

these options:

• FordigitalDVIsignals,connectanalogleft/right

audio to the TV’s

DVI/PC INPUT AUDIO

• ForHDMIsignals,noadditionalaudioconnection is required.

Power on the TV and computer. The TV will detect

the connection and display the New Device Found screen.

In the

New Device Found screen, press to

highlight PC in the list of device types. It is important to use the name PC so that the TV processes the computer signal correctly.

Press

BACK

to close the New Device Found screen.

An HDMI-to-HDMI connection carries all video and audio on a single cable.

jacks.

Note: If your computer provides digital audio out-

In Canada call 1(800) 450-6487 for assistance.

put (coaxial or optical), you can connect it directly to a digital A/V receiver and bypass the TV.

A DVI connection from a personal computer requires a separate audio connection.

1. Basic Setup and Operation 17

Using the TV with a Personal Computer, continued

Computer Video Adjustments

Power on the computer.

Select

press highlight to the PC icon, and press

Working from the computer, change the resolution

of the computer image. View the computer image on the TV and maximize the computer resolution while maintaining a suitable aspect ratio for the image.

Perform TV video adjustments.

options. Press

repeatedly to find the picture format (aspect ratio) best suited to the image. See the chart on this page showing how different computer resolutions can be displayed on the TV.

Distortion in Computer Images

Computer images may show distortion when viewed on the TV, e.g., lines that should be straight may appear slightly curved.

PC from the Activity menu. To do this,

ACTIVITY

then press 8 (VIDEO). Use

to cycle through video-adjustment

to open the Activity menu, move the

ENTER.

Press

then press 0 (FORMAT)

Tip

Set the computer’s screen saver to display a pattern after several minutes of inactivity. This acts as a reminder that the TV is powered on.

Computer Display Formats

Press

then press 0 (FORMAT) repeatedly to cycle through the

TV displays available for your computer’s video signal.

Computer Signal

Original Format

VGA 640 X 480

SVGA 800 X 600

Original Format Standard Zoom

XGA 1024 X 768

As Displayed on TV Screen

4 X 3

Standard

16 X 9

Standard

Zoom

Image Resolution

Your Mitsubishi TV can display the resolutions shown in the chart from standard VGA (640 x 480) through 1920 x 1080 signals at a refresh rate of 60 Hz.

In most cases, the computer will select the best resolution match to display on the TV. You can override this setting if you wish. Refer to your computer operating system’s instructions for information on changing the screen resolution.

You may need to restart the computer for changes to take effect.

PC 720p 1280 X 720

WXGA 1360 X 768

SXGA 1280 X 1024

Original Format Standard Reduce

PC 1080p 1920 X 1080

In the U.S. call 1(877) 675-2224 for assistance.

Before You Begin

TV Connections

Auto Input Sensing

The TV’s Auto Input Sensing feature automatically recognizes most connections and prompts you to identify the type of device connected. See page 13 for more on Auto Input Sensing.

Connection Types

Use the connection types available on your input devices that will give the best video quality. For example, choose HDMI over component video, and choose component video over composite video.

Picture Quality

For best picture quality, route signals directly from the input device to the TV whenever possible.

Cable Management

Surround Sound

For best surround sound audio quality, route audiosignal cables or HDMI cables from the source device directly to your A/V receiver or sound system.

IMPORTAN T

Accessory items such as cables, adapters, splitters, or combiners required for TV connections are not supplied with the TV. These items are available at most electronics stores.

Install the cable tie (supplied) in one of the mounting holes

on the back.

Lock the cable tie in place by pushing the end into the mounting hole.

To remove the cable tie, squeeze the side tabs and

In Canada call 1(800) 450-6487 for assistance.

pull out.

Sample cable routing. Secure the cable bundle with the release tab facing out.

Press the release tab to loosen the cable tie.

2. TV Connections 19

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

Inputs and Outputs

1. ANT (Antenna)

Connect your main antenna or direct cable service (no cable box) to

ANT

. The

ANT

input can receive digital and analog over-the-air channels from a VHF/UHF antenna or non-scrambled digital/analog cable source.

2. 3D GLASSES EMITTER

Use this jack for the special IR emitter supplied with 3D glasses. The emitter will send a signal that synchronizes your 3D glasses with the screen display. See page 29

3. IR–NetCommand Output/External Controller Input

Connect IR emitters to this jack to send control signals to external IR-controlled devices. This jack can also serve as the input for an external controller.

4. Y Pb Pr (Component Video)

Connect devices with component video outputs to this jack. Use the adjacent

and L jacks if you wish to send audio to the TV.

INPUT 1/INPUT 2

audio

USBa and LAN jacks

offered on L75-A91.

USBa

(power

only, page 34)

LAN

(page 34)

USB

(page 31)

RS-232 control jack is offered on L75 -A91.

RS-232

HDMI

(page 21)

VIDEO

(Composite Video)

Connect a VCR, DVD player, standard satellite

receiver, or other A/V device to the TV. Use the

adjacent

INPUT 1/INPUT 2

audio R and L jacks if you

wish to send audio to the TV.

6. L/R (Left/Right Analog Stereo Inputs)

Use with

and 5.

IR-NetCommand

Controller offered

INPUT 1/INPUT 2

Output/External

on L75-A91.

video inputs, items

(composite video,

(component video,

IR–NetCommand Output/External Controller Input

3D GLASSES EMITTER

ANT

VIDEO

page 23)

Y Pb Pr

page 21)

(page 51)

(page 29)

(page 22)

HDMI 4 offered

on L75-A91.

DIGITAL AUDIO OUTPUT

(page 24)

DVI/PC INPUT

(audio input,

page 22)

AVR AUDIO

OUTPUT

(page 24)

In the U.S. call 1(877) 675-2224 for assistance.

20 2. TV Connections

Inputs and Outputs, continued

7. HDMI™ Inputs

(High-Definition

Multimedia Interface)

The HDMI inputs support uncompressed standard and

high-definition digital video formats and PCM digital stereo audio.

Mitsubishi recommends you use category 2 HDMI

cables, also called high-speed HDMI cables, to

connect HDMI 1.3 source devices. High-speed category 2 cables bring you the full benefits of Deep Color

and x.v.Color.

These HDMI inputs can also accept digital DVI video

signals. To connect a device’s DVI output to the TV’s HDMI input, use an HDMI-to-DVI adapter or cable plus analog audio cables. Connect the analog audio cables to the

DVI/PC INPUT AUDIO

and right stereo audio from your DVI device.

Use the HDMI inputs to connect to CEA-861 HDMI com-

pliant devices such as a high-definition receiver or DVD player. These inputs support 480i, 480p, 720p, 1080i, and 1080p video formats.

The TV’s HDMI inputs are compatible with many DVI-D

and HDMI computer signals.

These inputs are HDCP (High-Bandwidth Digital Copy

Protection) compliant.

jacks on the TV to receive left

9. DVI/PC INPUT AUDIO

When connecting a DVI device to one of the TV’s HDMI inputs, use these jacks for left and right analog audio.

10. AVR AUDIO OUTPUT

Use

AVR AUDIO OUTPUT

current program to an analog A/V surround sound receiver or stereo system. Digital audio from digital channels and HDMI devices is converted to analog audio by the TV for output on this jack. This is the only audio connection needed to the TV if using an analog

A/V receiver or stereo system.

Headphones. These jacks can also be used for headphones that accept standard line level audio signals.

An adapter may be required.

to send analog audio of the

11. USB

The TV can read JPEG photo files and mp3 music files

from a USB device connected to the USB port.

12. RS-232C

L75-A91. Use the RS-232C interface to receive control

signals from compatible home-theater control devices. See www.mitsubishi-tv.com for a list of control signals for this interface.

8. DIGITAL AUDIO OUTPUT

This output sends Dolby Digital or PCM digital audio

to your digital A/V surround sound receiver. Incoming

analog audio is converted by the TV to PCM digital audio. If you have a digital A/V receiver, in most cases this is the only audio connection needed between the TV and your A/V receiver.

HDMI Cable Categories

HDMI cables are available as Standard and High-Speed types.

High-Speed HDMI Cables • (also called Category 2 Cables). Newer DVD players, video games, and set-top boxes require High-Speed HDMI cables, suitable for clock frequencies up to 340 MHz or data rates of up to

10.2 gigabits per second. Use high-speed cables for 1080p HD signals carrying extended color encodings (i.e., 30 or more bits, also called Deep Color). HighSpeed HDMI cables are also suitable for standard HDTV signals.

Standard HDMI Cables• (also called Category 1 Cables). Standard HDMI cables may be unmarked. They are suitable for standard HDTV 720p, 1080i, and 1080p signals with 8-bit color depth. Use category 1 cables for clock frequencies up to 74.25 MHz or data rates of up to 2.23 gigabits per second.

13. LAN

L75-A91. Use the

internet video to the TV. See page 34 for setup. Visit www.VUDU.com for details about VUDU™ service.

LAN

Ethernet jack for streaming

14. USBa

L75-A91. Standard USB 5-volt, 500-milliamp power

output you can use to supply power to an accessory device. For use with the VUDU wireless adapter, see page 34.

In Canada call 1(800) 450-6487 for assistance.

2. TV Connections 21

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

Any device with HDMI output

panel

PbY Pr

AUDIO

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

Pb Pr

Y/ VIDEO

Pb Pr

Y/ VIDEO

TV panel

CABLE IN or

SATELLITE IN

Incoming from cable service or satellite dish

Any device with component video output

Y Pb Pr Component Video Device

DMI Device

HDTV Cable Box, Satellite Receiver, DVD/ Blu-ray Player

If your source device has an HDMI output, use the connections for HDMI devices described on this page instead of Y Pb Pr component video.

Required:

1. RCA-type component video cables

2. Left/right analog audio cables.

Note:

To hear digital surround sound, connect the digital audio output from the device directly to your digital A/V receiver.

HDTV Cable Box, Satellite Receiver, DVD/ Blu-ray Player

Required: HDMI-to-HDMI cable.

Connect an HDMI cable from the TV back panel to the

HDMI device output. HDMI devices provide video and audio through the single cable.

Mitsubishi recommends you use category 2 (highspeed) HDMI cables to connect HDMI 1.3 source devices. High-speed category 2 cables bring you the full benefits of Deep Color and x.v.Color. See “HDMI Cable Categories” on the opposite page for more on HDMI cable types.

IMPORTAN T

HDMI and Audio Signals

Digital Surround Sound: The TV’s HDMI inputs can receive digital stereo audio signals only. To hear digital surround sound from an HDMI device, connect the device’s HDMI or digital audio output directly to your A/V receiver. See the Owner’s Guides for those devices for instructions.

In the U.S. call 1(877) 675-2224 for assistance.

22 2. TV Connections

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

DVI/PC

INPUT

DVI/PC

INPUT

DVI

OUT

AUDIO

Digital DVI device

panel

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

ANT

IN OUT

Cable TV

service

UHF/VHF antenna

TV panel

Not recommeded. Other connection types provide better quality audio and video.

Direct cable (no cable box)

Older cable

box

300-ohm-to75-

ohm combiner

(side view)

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

AUDIO OUT

COMPOSITE

VIDEO OUT

Y/ VIDEO

TV panel

Composite video cable

VCR or other device with composite video output

DVI Video Device

Cable Box, Satellite Receiver, DVD Player

Connect DVI devices (digital only) to the TV’s HDMI input jacks.

Required:

1. DVI-to-HDMI cable or DVI/HDMI adapter and HDMI cable

2. Analog stereo audio cables

If you are using a DVI/HDMI adapter, it is important to connect the adapter to the DVI device for best performance.

Some devices require connection to an analog input first in order to view on-screen menus and to select DVI as the ouput. Please review your equipment instructions for DVI connectivity and compatibility.

Note: The HDMI connection supports copy protection

(HDCP).

Antenna or Cable TV Service

Connect the incoming cable to the TV’s

ANT

input.

In Canada call 1(800) 450-6487 for assistance.

Composite Video Device

VCR or other device with composite video output

Required:

1. Composite video cable (usually yellow)

2. Analog stereo audio cables.

2. TV Connections 23

2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

AUDIO OUT

COMPOSITE

VIDEO OUT

COMPONENT

VIDEO OUT

Y/ VIDEO

Pb Pr

ANT

ANTENNA

1a.

1b. or

DVD Recorder or VCR

Incoming cable

RF Splitter

2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

AUDIO OUT

COMPOSITE

VIDEO OUT

COMPONENT

VIDEO OUT

Y/ VIDEO

Pb Pr

ANT

ANTENNA

OUT

1a.

1b. or

DVD Recorder or VCR

Incoming cable

Audio and video

from cable box

directly to TV,

preferably HDMI or

componenet

connections.

VCR or DVD Recorder to an Antenna or Wall Outlet Cable

Required:

1. Video cables 1a. Component video cables (red/blue/green)

1b. Composite video cable (usually yellow)

2. Left/right analog audio cables.

3. Two-way RF splitter

4. Two coaxial cables

Note:

Use composite video only if component video or • HDMI are unavailable. For an HDMI connection between the TV and recorder, see page 21. If your recording device has an analog-only tuner, • you must use a digital converter box to enable recording of digital broadcasts.

VCR or DVD Recorder to a Cable Box

Required:

1. Video cables 1a. Component video cables (red/blue/green)

1b. Composite video cable (usually yellow)

2. Left/right analog audio cables.

3. One coaxial cable

4. Video and audio cables required to connect the TV

to the cable box.

Notes: Use composite video only if component video or

HDMI are unavailable. For an HDMI connection between the TV and recorder, see page 21.

When using this connection conﬁguration, it is possible to view live cable programs through the recording device. For best picture quality always view live cable programs directly from the TV input connected to the cable box device.

In the U.S. call 1(877) 675-2224 for assistance.

24 2. TV Connections

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

OPTICAL

INPUT

COAXIAL

INPUT

COAXIAL

INPUT

DIGITAL

AUDIO

OUTPUT

DIGITAL

AUDIO

OUTPUT

AVR AUDIO OUTPUT

Digital coaxial

cable (for a digital

A/V receiver)

Stereo analog cables

(for an analog A/V receiver)

A/V receiver

back panel

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

HDMI

OUT

A/V receiver with HDMI output

Any connection types (can be HD or SD video)

AUDIO

DIGITAL

AUDIO IN

VCR

Cable box

DVD player

DIGITAL

AUDIO

OUTPUT

DIGITAL

AUDIO

OUTPUT

AVR AUDIO OUTPUT

Optional audio

connection

(analog or digital)

HDMI cable

A/V Receiver

Most setups require either a digital audio cable or analog stereo audio cables. To send audio from TV

channels received on the

nected directly to the TV, you must use one of the connections shown below. Usually, only one of these connections is required.

The TV makes all audio available in digital and analog

formats:

Analog audio coming into the TV is available as •

output in digital stereo format on the

AUDIO OUTPUT

Digital incoming audio is available as analog output • on the

AVR AUDIO OUTPUT L

jack.

ANT

input or devices con-

DIGITAL

and R jacks.

A/V Receiver with HDMI Output

Required: One HDMI-to-HDMI cable Optional: One digital coaxial audio cable or analog stereo audio cables

This option allows you to view content from devices connected to an A/V receiver. The A/V receiver can send audio and video to the TV over a single HDMI cable.

In addition to the HDMI connection, you can use • an audio connection from one of the TV’s audio outputs. The optional audio connection allows you to hear, through the A/V receiver, devices connected to the TV only, e.g., an antenna on the input.

You may be able to use the TV’s remote control (in •

mode) to operate connected CEC-enabled HDMI

devices. See Appendix C, page 73. L75-A91.• This setup allows you to use NetCom-

mand-controlled audio and video switching over the HDMI cable. See “Case 3: Automatic Audio and Video Switching via HDMI” on page 60.

L75-A91.• To use NetCommand to supplement HDMI control of a CEC-enabled A/V receiver, note the recommendations under “More About Using an HDMI Connection,” page 60.

ANT

Note:

In Canada call 1(800) 450-6487 for assistance.

On rare occasions, an HDMI signal may be • copy-restricted and cannot be output from the TV as a digital signal. To hear these copyprotected signals through the A/V receiver, use the connection for an analog A/V receiver.

Check the A/V receiver’s Owner’s Guide for • information concerning use of the digital input and switching between digital sound and analog stereo sound from the TV.

Using TV Features

Selecting an Input

The Activity menu lets you switch TV inputs. If you named devices during Auto Input Sensing, the inputs are organized into groups based on possible ways to use each device. Dots indicate the number of devices in each group. Note: Your setup may have only one group (Watch TV).

Press the

Use

Press

To change the list of inputs shown in each activity group, • see Inputs > Activity, page 45.

To assign or change the names of input icons, use the • Inputs > Name menu, page 45.

ACTIVITY

to move through groups of TV inputs.

to select an input.

ENTER

key.

to switch to the input.

Sleep Timer

The Sleep Timer turns the TV off after the length of time you set. To set the TV to turn on at a certain time of day, see the Initial > Timer menu on page

43.

Setting the Sleep Timer

Press

Viewing the Sleep Timer

Press

on the remote control. The TV’s MORE menu will display.

Press

CANCEL

The maximum is 120 minutes. Press

BACK

appear.

INFO

to see the time remaining on the Sleep Timer.

(SLEEP) repeatedly to increase the time in 30-minute increments.

or wait five seconds without pressing any keys for the message to dis-

SLEEP

With the MORE menu displayed, press the CANCEL key on the remote control to activate/deactivate the Sleep feature.

In the U.S. call 1(877) 675-2224 for assistance.

26 3. Using TV Features

ChannelView Channel Listings

ChannelView displays program descriptions sent by broadcasters. This information may be unavailable in some areas.

ChannelView. Programs for the tuned channel are listed on right side of screen.

ChannelView™ shows memorized channels on the input. It displays channel names and program information for digital channels as sent by broadcasters or your local cable service provider (information may be unavailable in some areas). No program information is displayed for analog channels.

ANT

Redirecting Audio Output

Selecting an Audio Output Device

Press

Note: The Headphones option displays only if you

and then

Press Speakers option will display only if there is a recognized audio device on an audio output or HDMI input.

Press phones, or TV.

to show the Speakers option. The

to select either AV Receiver, Head-

selected the name Headphones in the New Device Found screen.

(AUDIO)

Disconnecting an Analog A/V Receiver

When you disconnect an analog A/V receiver, change the Speakers setting to TV to hear sound from the TV speakers. Change the setting using the remote control’s

MORE > 9

Speakers menu.

(AUDIO )key or the Adjust > Audio >

Controlling A/V Receiver Sound Volume

Use one of the methods below to control sound volume from an A/V receiver.

Note: You must set the TV Clock (page 43) to receive

ChannelView listings for the current channel.

Using ChannelView

Feature Instructions

Display/hide ChannelView listings from the ANT input.

Receive updates for a digital channel.

Scan channels one by one.

Scan channels quickly.

Jump to listings for a specific channel.

See more of the program description for the current channel (if available).

Tune to the highlighted channel.

GUIDE

Press 1. to highlight a channel number. Press the 2. (the screen may

briefly go blank). Hold or

Hold PAGE UP/PAGE DN

Enter the channel 1.

number.

Press 2.

INFO

ENTER

INFO

ENTER

key

With a Standard TV Setup

Recommended Method:• Program the TV’s

remote control for your A/V receiver and enable the Audio Lock feature. See page 65.

Program the TV’s remote control for your A/V • receiver and set the TV remote control’s mode to

AUDIO

. Return the control mode to TV to control the

TV. Use the remote control that came with the A/V •

re ceive r.

With HDMI Control (CEC-Enabled HDMI A/V Receiver)

The TV’s remote control may control some functions of the A/V receiver. See Appendix C, “HDMI Control of CEC Devices,” page 73.

With NetCommand IR Control

Model L75-A91. Set up NetCommand control of the A/V

receiver’s volume functions in the Inputs > AVR menu. The TV’s remote will then control A/V receiver volume. See page 57.

In Canada call 1(800) 450-6487 for assistance.

3. Using TV Features 27

GUIDE

INFO

BACK

ACTIVITY

Status Display

Press the

INFO

the on-screen status display. The most common displays are shown here.

Sample information

from the on-screen

About Channel Numbers

Channel Numbers for Over-the-Air Reception or Reception by Direct Cable

Note: All signals are automatically converted to

Standard-Definition Analog Channels

Cable Reception

480i Stretch

Receiving Standard-Definition Analog Signal (480i)

Standard-Definition Digital Channels

Over-the-Air Antenna

SD 4:3 Stretch

Receiving Standard-Definition Digital Signal (SD)

High-Definition Digital Channels

Over-the-Air Antenna

HD 16:9 Stretch

Receiving High-Definition Digital Signal (HD)

key to see

status display

1080p for display.

Channel 3

Cable 3

Main Channel 7

Reception

Sub-Channel 1

Ant 7-1 KABC-SD

Main Channel 7

Reception

Sub-Channel 1

Ant 7-1 KABC-HD

402-101 KABC Monday Night Football

TV-PG DLSV St. Louis vs. Tampa Bay, played in Tampa for

Sleep 30 min

Tuesday 9:10 PM HD 1080i Standard

Surround English

1. Current Input

2. Audio Indicator.

TV speakers External sound system

Headphones Mute

3. Channel number (antenna source only) Digital channel includes major and sub-channel numbers.

4. Digital channel name (if broadcast); antenna source only.

5. V-Chip rating

Antenna source only for digital signal• Antenna or •

VIDEO

composite jack for

analog

signal

6. Program name (if broadcast); digital source only

7. Program description (if broadcast); digital

source,

antenna only. Press the

INFO

key additional

times to see more of the description.

8. Sleep Timer remaining time

9. Day and time

10. Signal type being received

11. Screen format in use

12. Program Audio indicator (antenna source only)

Digit•

al source: Stereo, Surround

Anal•

og source:

Stereo, Stereo SAP, SAP

13. Available language (digital source, antenna only)

14. Signal-strength indicator (digital source, antenna

only)

In the U.S. call 1(877) 675-2224 for assistance.

28 3. Using TV Features

TV Signals and Display Formats

This is a 16:9 widescreen TV suitable for images available from HDTV and many DVDs. You can view older-style, squarish images (4:3 aspect ratio) using one of the display formats described on this page. Press the MORE

0 key (

FORMAT

) to cycle through available display formats.

The TV remembers the format you last used for each input.

DVD Image Definitions

Image information may be stated on the DVD case. Some DVDs support both of the formats described below.

Anamorphic (or Enhanced for WideScreen TV)

Indicates DVDs recorded to show widescreen images properly on 16:9 TV sets using the TV’s Standard format mode (recommended)

Non-Anamorphic (or 4:3, 1.33:1, Letter Box, or Full Screen)

Indicates DVDs recorded for viewing on squarish TV screens. They may be full screen (4:3 or 1.33:1) which crops movies to fit the narrow TV, or letter box, which adds black top and bottom bars.

Signal Definitions

480i: Older type of interlaced signals from the

composite

VIDEO

, component

Y Pb Pr

480p: Progressive-scan DVD signals on component

HDMI

jacks.

720p and 1080i: High-definition signals received through

component

Y Pb Pr

HDMI

jacks. These signals are

always 16:9 (widescreen).

1080p: High-definition signals from a PC or Blu-ray player,

HDMI inputs only. SD 4:3: Standard-definition squarish-screen-format

signals from digital channels on the SD 16:9: Standard-definition widescreen-format signals

from digital channels on the

ANT

HD 16:9: High-definition 16:9 widescreen signals from

digital channels on the

ANT

input.

TV Display Format Definitions

Standard: The full-screen format used by HDTV signals.

Use this format to display anamorphic DVDs with a 1.78:1 or

1.85:1 aspect ratio. Anamorphic DVDs with a 2.35:1 aspect ratio are displayed correctly but with top and bottom black bars. Squarish (4:3) images are stretched evenly from side to side. Available for all signals.

Expand: Enlarges the picture to fill the screen by cropping the top and bottom; useful for reducing the letter box top and bottom bars of non-anamorphic DVD images.

Zoom: Enlarges the picture to fill the screen by cropping the sides, top, and bottom to eliminate black bars.

480i/480p and SD 4:3 signals:• Eliminates top and bottom bars on anamorphic DVDs with a 2.35:1 aspect ratio. 720p, 1080i, SD 16:9, and HD signals:• Eliminates bars added to squarish 4:3 images.

key and then the

, or

HDMI

ANT

input.

ANT

input,

jacks.

Y Pb

Original

Signal TV Display

Standard

Expand

Zoom

Stretch

Stretch Plus

Narrow

Non-anamorphic or SD 4:3

Distorted. Not recommended.

Recommended for letterbox. See Note 1.

Distorted. Not recommended. See Note 1.

Recommended for standard broadcasts. See Note 1.

See Note 1 Distorted; not

Anamorphic DVD

Recommended

Distorted; not recommended. See Note 1.

Recommended for anamorphic

2.35:1 images. See Note 1.

Distorted; not recommended. See Note 1.

recommended. See Note 1.

Note 1: Available for 480i, 480p, and digital SD 4:3 signals only.

Original Signal Display Formats

SD 16:9 or HD Digital 720p, 1080i, 1080p Signal

TV Display Formats. Press the repeatedly press the 0

key (

available for the current program. Press the

Wide Expand

Zoom

Recommended to remove side bars.

Recommended to remove bars from the top, bottom, and sides.

key and then

FORMAT) to see the displays

INFO

key to

see the name of the display format in use.

Stretch: Stretches a squarish 4:3 image across the screen to display the entire image with less distortion than the Standard format.

Stretch Plus:

Similar to Stretch, but minimizes distortion on the sides by expanding the picture to crop off portions of the top and bottom. Use to adjust the vertical position of the picture. L75-A91. Position adjustment may be unavailable if your NetCommand setup reassigned the

keys for the current device.

Narrow: Displays narrow 4:3 images in their original shape. Adds black side bars to fill the screen.

Wide Expand: Enlarges the picture, cropping the image on both sides. Removes or reduces black side bars added to narrow images converted to 16:9 signals for digital broadcast.

Note: All high-definition channels send widescreen (16:9) signals, but not all programming was created for the widescreen format. The broadcaster may stretch the image or add side bars to fill the widescreen area.

In Canada call 1(800) 450-6487 for assistance.

3. Using TV Features 29

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

GLASSES

EMITTER

3D Video

Press

To display 3D gaming or 3D cinema content, your Mitsubishi LASERVUE® TV requires:

A compatible 3D source device• Either checkerboard or Split HD format • Active 3D glasses•

The TV’s 3D options are in the Adjust > 3D Mode menu described on page 41.

Initial Setup

Check if your HDMI 3D video source device outputs

a 1080p 60 Hz signal. This information will be needed later when you assign an input name in the New Device Found screen.

If your 3D glasses came with an emitter box,

connect the emitter box to the

EMITTER

jack. Place the box in front of the TV

where there is a clear path to the glasses.

3D GLASSES

Watching 3D Video

Note: Active 3D glasses are required.

BACK

to close the New Device Found screen.

Press

ACTIVITY

Highlight the icon for the 3D video device and press

ENTER

Press

and select the Adjust > 3D Mode

menu. Select

On for 3D Mode. The On setting will be memorized for the current input when you exit this menu.

Note: If your glasses are marked DLP Link, skip this

step; no emitter box is required with DLP Link technology.

Select the source format.

Checkerboard is the standard 3D format for • DLP TV and is compatible with current PC 3D gaming. Top/Bottom may be used by some sources and •

Power on the TV and the source device.

Connect the source device to the TV’s HDMI input.

When the

New Device Found screen displays,

name the input according to the table below. Note that the TV will process the video signal differently

can be identified by the screen being divided into two images, one above the other.

Select the glasses control type

. For glasses with an emitter box, select • IR Emitter. For glasses marked • DLP Link, select DLP Link.

depending on the name you assign. If your source

Press

device is a Blu-ray disc or game console, the signal must be 1080p at 60 Hz.

3D Video Source

3D Video Signal

Recommended: 1080p 60 Hz (1920 X 1080). The image will fill the TV screen. Other 60-Hz computer video signals compatible with the TV will

Computer

display with black bars. See page 17. To see 3D video, the signal must be

1080p 60 Hz

Other

Assign Name

Any other name

To Watch Regular (non-3D) Content

The 3D Mode setting is memorized for each input. When you want to watch non-3D images on the input selected above, open the Adjust > 3D Mode menu and set 3D Mode to Off.

BACK

to close the menu.

If the image does not appear correct appear to be moving in instead of out),

(e.g., objects

open the

Adjust > 3D Mode menu and set Glasses L-R to Reverse.

In the U.S. call 1(877) 675-2224 for assistance.

30 3. Using TV Features

3D Video, continued

3D Safety Requirements

3D Glasses are NOT designed as sunglasses or safety glasses and do not provide protection. 3D glasses should • be worn only when viewing 3D material. Do not wear the wireless glasses in any situations that require unimpaired visual perception.• Children under the age of 5 should not view 3D programming.•

Under normal conditions, 3D viewing is safe for your movies or games. Some people may experience discomfort, however. To minimize the potential for experiencing visual problems or any adverse symptoms:

Read and follow any and all safety warnings that accompany your 3D glasses or 3D source devices.• Maintain a distance of no less than 2 to 2.5 times the screen height measurement away from the display. Viewing • from too short a distance can strain your eyes. Take regular breaks, at least 5 minutes after every hour of 3D viewing.•

If you experience any of the following symptoms, discontinue 3D viewing until the symptoms go away:

nausea, dizziness, or queasiness, • headache, or eyestrain, • blurry vision,• double vision that lasts longer than a few seconds,•

Do not engage in any potentially hazardous activity (for example, driving a vehicle) until your symptoms have completely gone away. If symptoms persist, discontinue use and do not resume 3D viewing without discussing your symptoms with a physician.

Do not use the glasses where loss of balance or limiting your field of vision may be dangerous to you. Do not use near staircases, ledges or balconies. You may risk falling during or after use.

Epilepsy

WARNING! IF YOU OR ANY MEMBER OF YOUR FAMILY HAS A HISTORY OF EPILEPSY, CONSULT A PHYSICIAN BEFORE USING COMPUTER GAME PRODUCTS.

A small percentage of the population may experience epileptic seizures when viewing certain types of TV images or video games that contain flashing patterns of light.

The following people should consult a physician before viewing 3D Games or Video:

Anyone with a history of epilepsy, or who has a family member with a history of epilepsy• Anyone who has ever experienced epileptic seizures or sensory disturbances triggered by flashing light effects.•

WARNING! SOME LIGHT PATTERNS MAY INDUCE SEIZURES IN PERSONS WITH NO PRIOR HISTORY OF EPILEPSY. DISCONTINUE 3D VIEWING IF YOU EXPERIENCE ANY OF THE FOLLOWING SYMPTOMS:

Involuntary movements, eye or muscle twitching• Muscle cramps• Nausea, dizziness, or queasiness• Convulsions• Disorientation, confusion, or loss of awareness of your surroundings•

Do not engage in any potentially hazardous activity (for example, driving a vehicle) until your symptoms have completely gone away.

Do not resume 3D viewing without discussing the symptoms with your physician.

Notice Concerning Format Compatibility

In order to display 3D images. Mitsubishi 3D Ready DLP Home Cinema TVs require the use of a 3D source device coupled with the Mitsubishi 3D adapter or other source

In Canada call 1(800) 450-6487 for assistance.

devices that support checkerboard display formats for display of 3D games, 3D broadcasts from terrestrial/cable/ satellite and 3D Blu-ray disc content. In all cases an emitter and matching 3D active shutter glasses or DLP Link active shutter glasses are required in order to view 3D content.

3. Using TV Features 31

Camera and Music Files

From the USB Menu you can:

The TV can read photo or music files from a USB • device. Photos must be in JPEG format and music files must be in mp3 format. To play music files while displaying a photo slide show, see “USB Media Setup Menu” on the next page.

The TV can display still or moving images from a • camera through the and Moving Video as Composite Video,” page 33.

Y/V I D E O

port. See “Photos

The USB Media Player Menu

Activate any of the menu options

Display the Activity menu.

Display the main menu.

Display status for the USB device.

To resume use of the USB port after switching the

TV to a different input, press Photos, and select the USB icon port.

Highlight an icon and press

ENTER

Press clear.

ACTIVITY.

MENU.

INFO.

Press again to

Press

ACTIVITY

, choose View

BACK

Displaying the Menu

Back up the data on your USB drive before con-

necting it to the TV. Mitsubishi is not responsible for any file damage or data loss.

Connect your USB drive to the TV’s USB port.

The USB Media Player menu displays while files are being read. Wait until icons appear in the menu before continuing.

IMPORTANT

Do not use USBa for this purpose. The TV is unable to read files from the USBa port.

Playing a Slide Show or Playlist

Use these keys while playing a slide show or playlist.

Replays the slide show or playlist.

ENTER

Pauses a slide show or playlist.

Stops a slide show or playlist.

Displays the previous or next slide.

GUIDE

BACK

ACTIVITY

INFO

Always stop playback with ( to a different TV input before disconnecting your USB device.

Plays the previous or next track. Rotates an image clockwise in 90˚ incre-

ments. Displays the USB Media Player menu.

Displays the main menu and stops play.

Displays the Activity menu and stops play.

Displays slide name or track name. Press

BACK

to clear.

IMPORTAN T

STOP

) or change

The TV can read JPEG files as created by the camera. If you edit a picture file on a computer and resave the image, the TV may be unable to read the resaved file.

In the U.S. call 1(877) 675-2224 for assistance.

32 3. Using TV Features

Camera and Music Files, continued

Thumbnail and Playlist

JPEG Thumbnail Menu

Use these keys while viewing JPEG thumbnail images or the music tracks in a playlist.

GUIDE

ENTER

PAGE UP/DN

BACK

ACTIVITY

Picture Files Compatible with the USB Port

• Stillimagesrecordedondigitalcamerasusingthe

Exchangeable Image File Format, version 2.1 (EXIF

2.1) standard for digital still cameras and Design Rules for Camera File Systems version 1.0 (DCF 1.0)

• Someimagesopenedandresavedonacomputer

may not play back or may not display in the thumbnail list. This happens if the files were resaved in an incompatible format.

• Fullpathfilenamescanbenolongerthan50characters and must end in a .jpg extension. Only the first 20 of the 50 characters will display.

Moves the highlight from item to item. Rotates a thumbnail clockwise in 90˚

increments

Plays the slide show or playlist starting

with the highlighted item.

Selects the last item on the current page.

Selects the first item on the current page.

Displays the next or previous page of items.

Displays the USB Media Player menu.

Displays the main menu.

Displays the Activity menu.

Menus

USB Media Setup Menu

Use the USB Media Setup menu set up play of a slide show or playlist.

• IfJPEGimagefilesandmp3filesareontheUSB

device, choose:

Slideshow + Music Slideshow Music only -

Slideshow.• Select either Auto or Manual advance

for the slide show. During manual operation, press

ENTER

to advance to the next slide.

Interval.• For automatic advance, select the time interval for display of each slide. The interval you select here is the minimum time between slides; actual time may be longer for larger files.

Frequency.• number of times (frequency) to play the complete slide show and/or playlist:

Press •

BACK

return to the Media Player menu.

Notes on Using the USB Port

• TheTVignoresallcommandswhilereadingfiles.

until the Play icon appears highlighted and in full color before continuing.

• Largefilesorhigh-capacitystoragedevicesmaytakea

long time to display.

•

The TV can read files up to 10 MB in size with a maximum of 2,500 files stored on the device. The FAT16 or FAT32 file system is recommended.

• UseaUSBdriveinsteadofacardreader.

• BackupthedataonyourUSBdrivebeforecon-

necting it to the TV. Mitsubishi is not responsible for any file damage or data loss.

Note:

Some manufacturers’ USB devices may be incompatible with the TV. If the TV is unable to display your photos, you can:

• Transfer

• Useyourdigitalcamera’scompositevideo

For automatic advance, select the

Once, Twi ce, or Continuous.

to close the Media Setup menu and

Wait

files to a different USB device.

output. See page 33.

In Canada call 1(800) 450-6487 for assistance.

3. Using TV Features 33

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEOLY/ VIDEO

Y/ VIDEO

Composite video cable

Optional audio cable

Audio-only

device

Unused

RCA-style plug

(plug in ﬁrst)

Y/ VIDEO

Camera Images and Music Files, continued

Photos and Moving Video as Composite Video

Connect the camera to the TV using a composite video cable if:

• YouareunabletoseeimagesusingtheUSBport.

•

You wish to view moving video from the camera.

Control the slide show or movie through the camera as the TV’s USB Media Player menu will be unavailable. The display resolution will be standard-definition (480i).

Refer to the owner’s manual supplied with the

camera for instructions needed for this setup. Set the camera’s output signal type to

put the camera into playback mode. With the camera still turned on, connect your digital

camera’s composite video cable (usually yellow) to the TV’s camera’s audio output cable to the

Y/V I D E O

jack. To hear audio, connect the

NTSC and

AUDIO L

jack.

Using an Audio-Only Device

Keep an unused RCA-style connector in the jack while using an audio-only device such as an MP3 or CD player.

Y/V I D E O

Camera connection using a composite video cable

When the

assign the name Camcorder. Press

BACK

Press

ACTIVITY,

press

ENTER

If viewing photos, advance through the images manually or set the camera to advance automatica lly.

New Device Found screen displays,

to close the New Device Found screen.

select Watch Movie > Cam, and

In the U.S. call 1(877) 675-2224 for assistance.

34 3. Using TV Features

1 2 3 4

HDMI

DIGITAL

AUDIO

OUTPUT

RS-232C

DVI/PC

INPUT

Y/ VIDEO

Ethernet

cable

Internet router or modem

Incoming high-speed internet service

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

USB-to-DC power cable

AC-to-DC power cable

VUDU Wireless Box 2

Router or modem

Ethernet

cable

Ethernet cable

VUDU Wireless Box 1

Streaming Internet Movies with VUDU

L75-A91. This TV’s built-in VUDU™ capabilities allow you to access your own personal home video store right on your TV. VUDU’s service offers you:

The largest on-demand HD movie selection any-• where, featuring full 1080p and 5.1 surround sound.

All of Hollywood’s latest hits and classics. Movies • are available to rent or buy the same day the movie comes out on DVD.

VUDU allows you to enjoy movies with no store • visits, no mailing, no late fees and no subscriptions.

Parental controls allow you to restrict access to • content according to MPAA ratings. See the VUDU Info & Settings menu.

VUDU features popular internet applications provid-• ing free content.

Standard Connection

Connect the TV to your network router or directly to a high-speed internet modem using an Ethernet cable (not supplied).

At the time of this writing, VUDU requires an internet bandwidth of 4.0 Mbps or higher for instant HD video and 2.0 Mbps or higher for instant SD video. These specifications are subject to change. Visit www.VUDU. com to learn more about available titles, prices, recommended bandwidth, and services offered. For a list of recommended routers and switches, see the Support >

FAQ section at VUDU.com.

Required for VUDU Service

Broadband internet service• Ethernet cable • or the VUDU wireless kit. Computer access to the VUDU.com website •

(required for one-time account activation). A credit card for rental and purchase transactions.•

VUDU Wireless Kit

The VUDU wireless kit is available for purchase from VUDU.com. The kit includes the two wireless boxes, two power cables, and two Ethernet cables shown in the diagram below. VUDU capabilities are built right into the TV, so connect VUDU Wireless Box 2 directly to the TV as shown.

The LED indicators for • light up once power is applied to the boxes.

After a few seconds, the LED indicator for •

WIRELESS

will start to blink, indicating the wireless

adapters have been set up successfully. The LED indicators for •

will blink when data is being transmitted.

POWER

and

WIRELESS

ETHERNET

and

ETHERNET

will

Standard VUDU connection via Ethernet

In Canada call 1(800) 450-6487 for assistance.

Connecting the VUDU wireless kit. Connect VUDU Wireless Box 2 directly to the TV.

3. Using TV Features 35

F3 F4F2

FAV

DEMAND

GUIDE BACK

ACTIVITY

Streaming Internet Movies with VUDU, continued

Getting Started

To start using VUDU, connect your TV to the inter-

net as described in the previous section. Power on the TV.

Press

Once your account is activated, you can rent and buy movies using only the TV and the TV’s remote control.

ACTIVITY

In the

Watch Movie activity, highlight the VUDU

icon and press

to display the Activity menu.

ENTER

. Browse the VUDU catalog and offerings. When you are ready to rent or buy a movie, you

will be prompted to activate your VUDU account. Follow the on-screen instructions and use a computer to go to www.VUDU.com/activation. A credit card is required for activation.

Troubleshooting

If the VUDU Screen Is Not Responding

Press

and then 2 (RESET) to reset VUDU. This

resets VUDU only and does not affect TV settings.

If You Are Unable to Connect to VUDU

Check all power and data connections.• If you can reach the internet with a computer or • other device on the same internet service used by the TV, consult the router or modem owner’s guide for reset instructions. If you cannot reach the internet, contact your • service provider. You may be asked for network information such as the TV’s IP address. Press the

key and then press 1 (NETWORK).

For Further Assistance

If you are having trouble connecting your TV or • accessing internet applications, contact Mitsubishi Customer Care at 1If you are having difficulty with your VUDU • account, contact VUDU Customer Care at www.VUDU.com/support. See more troubleshooting tips in the • TV Reset Comparison Guide starting on page 77.

877-675-2224

Using VUDU

ACTIVITY

Navigate VUDU’s menus with the keys on the TV’s remote control. Browse the movie catalog, watch movie previews, set parental controls, and rent or buy movies.

To exit VUDU, press

ACTIVITY

and

select a different TV input.

PAGE UP/PAGE DOWN

Jumps to the previous/next page of menu items.

PLAY/PAUSE

Starts or pauses video playback.

FAST FORWARD/REVERSE

Press to search scenes forward • or back. Press additional times to speed • up search. Press opposite key to slow and • pause search.

STOP

Stops video playback and returns to the previous menu.

Goes to the previous screen.• Stops video playback and returns to the • previous menu.

VUDU

PLUS

. Displays more options for

the current selection (if available).

Returns to the VUDU home menu while in VUDU.

ENTER

Selects a menu item.• Pauses video and displays a scene-• selection strip for frame-by-frame search. Press again to resume play.

Directional navigation

Displays the TV’s MORE menu with these special VUDU options:

Displays network information useful for troubleshooting.

Resets VUDU if VUDU stops responding to commands.

In the U.S. call 1(877) 675-2224 for assistance.

36 3. Using TV Features

Introduction to Home-Theater Control

This TV offers a choice on home-theater-control systems. This summary offers some examples of the control methods available using the TV’s remote control. You may wish to use one or more of these methods in your home theater after completing Auto Input Sensing.

Source device connected directly to the TV

Remote Control Programming (Any Connection Type)

Program the remote control to operate the A/V device. To control the device, set the remote control to the correct mode for the device type. See Appendix A, “Programming the Remote Control.” In the case of an A/V receiver, use the Audio Lock feature, page 65.

CEC-Enabled HDMI Device (HDMI Connection Only)

See Appendix C, “HDMI Control of CEC Devices,” page 73.

Model L75-A91. NetCommand IR Control (Any Connection Type)

Set up NetCommand IR control of the device’s keys as desired. See “IR Emitter Placement,” page 51, and “Initial NetCommand Setup,” page 52.

Source device connected to an A/V receiver connected to the TV

CEC-Enabled HDMI A/V Receiver

The TV’s remote control may operate some functions of a connected A/V device. You can switch to the device by selecting its icon in the TV’s Activity menu. See Appendix C, “HDMI Control of CEC Devices,” page 73.

Any Connection Type

A/V

Device

CEC-Enabled

A/V Device

Any Connection Type

A/V

Device

CEC-Enabled

Source Device

A/V Receiver

HDMI Cable

HDMI

Cable

HDMI

Cable

Model L75-A91. A/V Receiver with HDMI Output (no CEC)

Set up NetCommand IR control of the 1. A/V receiver’s keys as desired. See “IR Emitter Placement,” page 51, and “Setting Up A/V Receiver Control,” page 57.

Set up NetCommand IR control of the 2. source device’s keys as desired. See “NetCommand Control of a Device Connected to an HDMI A/V Receiver,” page

61.

In Canada call 1(800) 450-6487 for assistance.

Source Device

A/V Receiver

Any Con-

nection Type

HDMI Cable

Main Menu

Press

on the remote control to open the main menu and then select from one of these categories.

TV Menus

Adjust

Captions

Initial

Input

Lock

Menu Navigation

Displays or clears the main menu.

Customize picture and sound settings; enable 3D mode. 38

Turn closed captions on and off; customize caption displays. 42

Perform basic TV setup. Set language, scan (memorize) channels and edit

channel options, set the TV clock, set auto-on TV Timer.

Assign names to TV inputs, enable HDMI Control, assign activities to inputs.

Model L75-A91. Perform NetCommand IR “learning.”

Restrict TV use. Disable the control-panel buttons. Set a pass code. 47

Moves up one menu level.• Clears the current menu.•

Moves navigation into options • area.

Selects an item.• Moves the highlight within menus. Makes adjustments in some

menus.

Look for the key guide at

the bottom of each menu.

In the U.S. call 1(877) 675-2224 for assistance.

38 4. TV Menus

Adjust

Picture

Mode

To make picture adjustments:

From the • Adjust > Picture menu:

Press 1. to highlight an option. Press 2. to adjust.

While watching TV:• Press the then 8 (VIDEO)

Super Brilliant

Brilliant

Game

Bright For most daytime viewing under natural light; good for x.v.Color

Natural For most nighttime viewing under dim to moderate lighting; good for x.v.Color sources

Cinema For use with theatrical movies; recreates the color gamut seen in theaters. Good for movie

Special Advanced Picture Modes. Contact your professional installer for setup or see

ISF Day, ISF Night

in the on-screen menu. Press

The Super Brilliant Picture Mode is designed to compensate for the harsh, bright lighting used in retail settings and is not recommended for home use. Prolonged use of the Super Brilliant Picture Mode will age the lasers faster, reducing picture brightness as the TV ages.

For use under bright light. May be too bright for most home lighting; unavailable when the current input is named Game

Optimizes picture and video processing for gaming consoles. Available only when the name of the input is

sources

viewing in moderate to dim lighting.

“Advanced Picture” on page 41.

L75-A81: Special/ADV L75-A91: ISF Day/ADV1, ISF Night/ADV2

key and

to select the video option you want to change.

Press to change settings.

Assign names to TV inputs before making video adjustments (New Device Found or Inputs > Name menu). Adjustments will be reset to the defaults if you name or rename inputs afterwards.

Set the Picture Mode first before changing other video settings, as some settings are stored independently

or PC.

Game or PC.

for each Picture Mode. Use Picture Modes to get the best image under different viewing conditions.

Low contrast shows a variety of shades in darker images• In most home lighting situations, medium contrast looks best.•

Contrast

Brightness

Color Adjusts overall color intensity from no color to fully saturated.

Tint Adjusts the red-to-green ratio.

Sharpness

Color Temp

Video Noise

EdgeEnhance

High contrast shows darker images more uniformly black and • makes colors appear more vibrant. High contrast is good for brightly lit environments.

Adjusts overall picture brightness. Settings are stored independently for each Picture Mode.

Adjusts picture detail and clarity.

High

Low

High, Medium, Low, Off

On, Off EdgeEnhance™ adds special edge enhancements to make the image appear sharper.

Gives white images a cool cast. May provide the most realistic picture under bright lighting.

Gives white images a warm cast. This setting displays video at approximately the 6500K industry standard for NTSC pictures.

High.• For poor-quality signals. Medium. • Low. • For good-quality signals. Off. • Leaves the picture unaltered.

Saved by input.

For moderate noise reduction.

Adjusts the white-to-black level Settings are stored independently for each Picture Mode.

Adjusts the white balance. Settings are stored independently for each Picture Mode.

Reduces minor noise (graininess) in the picture. Saved by input. Not available if the current input is named PC or Game or when 3D is active.

DeepField Imager

On, Off DeepField™ Imager dynamically enhances black levels in portions of the screen to

provide strong contrast with detail over mixed screen content.

Demo For comparison, displays a split picture to show On (right side) and Off (left side).

In Canada call 1(800) 450-6487 for assistance.

4. TV Menus 39

Adjust, continued

To make audio adjustments:

From the • Adjust > Audio menu:

Audio

Speakers The Speakers option displays only if an A/V receiver or headphone connection has been

Press 1. to highlight an option Press 2. to adjust.

While watching TV:• Press the (AUDIO) in the on-screen menu. Press to select the audio option you want to change. Press to change settings.

detected. Detection occurs on the right and any HDMI jack.

TV Turns on the internal TV speakers.

key and then 9

AVR AUDIO OUTPUT

jack, the

DIGITAL AUDIO OUT

jack,

AV Receiver

Headphones

Bass Controls volume of low-pitched sound from the TV speakers.

Treble Controls volume of high-pitched sound from the TV speakers.

Balance Controls audio balance between the right and left TV speakers

Sound Mode Stereo No special audio effects from the TV speakers

Surround Modifies audio from the TV speakers.

Listen To

Available only for analog channels from the

ANT

input

Language Selects the current language for a digital program from the

Stereo The TV plays stereo broadcasts in stereo and mono broadcasts in mono. The

Mono Reduces background noise. Use when receiving a weak stereo audio signal. All

SAP

(Second Audio Program)

include from zero to seven language choices.

Turns off the TV speakers so you hear sound only from a connected A/V receiver. Adjust the sound volume using the A/V receiver controls.

Note: When you disconnect an analog A/V receiver, be sure to change the Speakers setting to TV to hear sound from the TV speakers.

Turns off the TV speakers so you hear sound only from connected headphones. See “10. AVR AUDIO OUTPUT,” page 20. Adjust the sound volume using the TV’s volume controls. The Headphones option displays only if you selected the name Headphones in the New Device Found screen for the available if

• Formonaural(non-stereo)programs,createsasimulatedstereoeffect.

• Forstereoprograms,createsasimulatedsurround sound effect.

word Stereo is displayed when you tune to a channel broadcasting in stereo.

audio is played as mono with this setting. Selects an additional monaural sound track not audible during normal TV viewing.

The SAP signal might be related to the program (such as a sound track in a foreign language), or it might be unrelated (such as a weather report). If an SAP signal is broadcast, the letters SAP are displayed when you tune to the channel.

DIGITAL AUDIO OUTPUT

AVR AUDIO OUTPUT

is connected.

ANT

jack.

This option is not

input. Each digital program may

Available only for digital channels from the

Level Sound On, Off Reduces differences in sound volume between programming segments, such as

the difference between regular broadcast programs and commercial segments.

ANT

input.

In the U.S. call 1(877) 675-2224 for assistance.

40 4. TV Menus

Adjust, continued

Reset Resets audio and picture adjustments for the current input. Highlight the • Reset icon and press

ENTER

twice

Reset• has no effect on global settings (Balance, Listen To, Language, Film Mode) or on Advanced Picture.

Global Video Mute

(non-antenna inputs only)

Audio Screensaver

Film Mode

(480i and 1080i signals only)

On Displays a solid colored background when there is no video signal

from the current input. The colored screen reminds you that the TV is powered on when there is no picture. The TV will power off after five minutes without receiving a video signal.

Off The screen appears black when there is no video signal from the

current input.

On, Off Select On to display a random pattern while playing an audio-only

input. To use this feature, the input must be either

Named as an audio source (e.g., • CD or MP3 Player)

Be the •

Auto, Off In Auto, the TV automatically detects and applies film-decoding

correction to movies filmed at 24 frames per second. Try the Off setting if images show many jagged edges.

ANT

input playing an audio-only program.

Smooth 120 Film Motion

Blue Glow On, Off

Test Picture

Standard, High, Off

Displays a high-definition test picture.

L75-A81

Standard:• Removes judder (image vibration) and smooths

motion scenes in film-based content such as movies.

High:• Removes more judder in motion scenes in movies. Off:• Use this setting if Standard or High create image noise.

L75-A91. Removes judder (image vibration) and smooths motion

scenes in film-based content such as movies.

Highlight the icon and press 1. screen.

Press 2. to change the amount of correction or set to zero to turn off the correction.

Press 3.

BACK

to return to normal TV viewing.

L75-A91.

Select On to see blue accent lighting.

ENTER

to display an adjustment

In Canada call 1(800) 450-6487 for assistance.

4. TV Menus 41

Adjust, continued

Picture+

PerfectColor Sliders

PerfectColor

Using PerfectColor:

Highlight the PerfectColor™ icon and press independently for each TV input.

Using PerfecTint

•

To switch between PerfectColor™ and PerfecTint™ adjustments, highlight

• Press to move from one color bar to the next.

• Press to change settings.

• Press

CANCEL MENU

Advanced Picture

Press 1.

With 2. Picture Mode highlighted, press L75-A91: Choose

Use 3.

to Press 4. Use 5.

to Press 6.

settings

to restore default settings.

to return to the main menu.

. Under Picture+, highlight the Advanced Picture icon and press

highlight an option you wish to change and press ENTER

to change settings.

navigate to additional options and press to return to the Advanced Picture menu. Press

. The

Advanced Picture adjustments will be in effect for the current input.

PerfectTint Sliders

ENTER

Advanced Picture allows you to save highly customized picture adjust- ments for each input. Mitsubishi recommends a professional installer make these adjustments.

ENTER

ADV1 (daytime settings) or ADV2 (nighttime settings).

Adjusts the saturation (intensity) of six colors for the current image source.

Adjusts six hues for the current image source

to display the PerfectColor menu. Settings are retained

to change

from blank (undefined)

to change settings

Adjust Mode and press

ENTER

ADV

to see the adjustment display.

again to close the menu and save

3D Mode

To use the custom Picture Mode at a later time

Press

and go to Adjust > Picture > Picture Mode and:

L75-A81 L75-A91

Select •

SPECIAL if settings were saved by

your professional installer. Otherwise select • ADV.

To return to the default values for Advanced Picture Display the Picture+ > Advanced Picture menu and:

L75-A81 L75-A91

ENTER

Highlight RESET Pic Mode and press

3D Mode

Source Format

Glasses L-R Standard,

Glasses Control

On, Off

Checkerboard, Top/Bottom

Reverse

IR Emitter, DLP Link

Use the On setting for video games and movies that require 3-D glasses. This setting applies only to the current input. Note: 3D options are available only for 1080p 60-Hz video sources connected to an HDMI input.

Selects the source format.

Synchronizes the 3D glasses with the image on screen to provide the best 3D effect. Try

Selects the control type for your 3D glasses.

Sele• saved by your professional installer.

Otherwise select • ADV1 or ADV2.

Highlight the 1. Advanced Picture mode to change. H2. ighlight RESET Pic Mode and press

Repeat this separately for both ADV1 and ADV2.

ct ISF Day or ISF Night if settings were

ENTER

Reverse

Standard

seems incorrect.

In the U.S. call 1(877) 675-2224 for assistance.

42 4. TV Menus

Captions

Captions on Analog Channels

The TV can decode captions from the

the composite either standard closed captions or text service. Standard closed captions follow the dialogue of the program and display in a small section of the screen. Text-service closed captions often conta

news and cover a large portion of the screen.

VIDEO

jacks. Broadcast

in information such as weather or

ANT INPUT

ers can send

and

Captions on Digital Channels

The TV can decode captions from the ANT input only. Broadcasters can send up to six different captioning selections or can send analog captions for a program that originated in analog format. A TV station may broadcast only one or two types of captions or none at all

Services

Effects

(for captions from digital channels)

Digital On if Mute

Caption 1– Caption 6 Off

Analog

Analog Background

Font

Font Size

Font Color White, Black, Magenta, etc. Guidelines for setting digital captions:

Font Opacity Translucent, Opaque, Flashing,

Background Color

Background Opacity

On if Mute CC 1–CC 4 Text 1–Text 4 Off

Gray, Black Selects either a gray or black text background to make analog

Default Font 1–Font 7

Large Medium Small

Transparent

White, Black, Magenta, etc.

Translucent, Opaque, Flashing, Transparent

closed captions easier to read. Default changes settings to those selected by the captions pro-

vider, or, if none, to the TV’s own caption defaults. Use Fonts 1 through 7 to give captions on digital channels a custom appearance.

Large is the recommended size.

IMPORTAN T

• Analog text-service options display a large black or gray box on the screen when no signal is being broadcast.

• Thecontentofcaptionsisdeterminedbythe

broadcaster. If captions show strange characters, misspellings, or odd grammar, it is not a malfunction of the TV.

•

Closed-caption signals are not available through HDMI or component jacks. See the menus for devices connected to these inputs for closedcaption decoding.

On if Mute:• Displays digital closed-caption signal Caption 1

when audio from the TV speakers is muted. When watching TV, press Caption 1–Caption 6: • Caption signals sent by the broad- caster

On if Mute: • Displays analog closed captions signal CC 1 when audio from the TV speakers is muted. When watching TV, press

CC 1–CC 4:• Standard closed-caption signals Text 1–Text 4: • Text-service signals

MUTE

to turn closed captions on/off.

MUTE

to turn captions on/off.

• A white font on a black translucent background makes an easy-to-read combination.

• Usecontrastingcolorsforcaptionsand

background.

In Canada call 1(800) 450-6487 for assistance.

4. TV Menus 43

Initial

Language

Clock

English Spanish

Set the TV clock to:

Use the TV Timer to power on the TV automatically at a preset time• Receive correct updates to ChannelView listings•

Note: When the Daylight Savings Time change occurs, you must open this menu and set the TV’s clock ahead or back.

Time

Date

Time Zone

DST On, Off Daylight Savings Time. Select the setting for your area.

Displays on-screen menus in either English or Spanish.

Note: Listen To > SAP (analog signal) or Language (digital signal) on page 39.

Eastern, Central, Mountain, Pacific, etc. The correct time zone is required for accurate ChannelView updates.

To listen to audio in other languages (when available), see

With the hour highlighted, press 1. to change the hour and the AM/PM indicator. Press and hold to change the hour display quickly. Press 2.

ENTER

to set the hour. With the minutes highlighted, press 3. to change the minutes. Press and hold to change the minutes display quickly.

With the month highlighted, press 1. to select. Press ENTER With the day highlighted, press 2. to select. Press With the year highlighted, press 3. to select the current year.

correct DST setting is required for accurate ChannelView updates.

Adjust > Audio >

to set.

ENTER

to set.

The

Timer

Timer On, Off Select On to enable the Timer.

The Timer tells the TV to power on automatically at a time you set. Use this menu to set a day, time, input, and channel for the Timer. If the TV is already on at the requested time, the TV will automatically change to the designated channel or input.

• TheTVclockmustbesetbeforeyoucanusetheTimerfeature.

• ToremindyouthattheTVTimerhasbeenset,the

slowly while the TV is powered off.

• WhentheTimerturnsontheTV,pressanykeyontheremotecontroltokeepiton.Otherwise,

the TV will turn off after five minutes.

Day Daily, Mon-Fri, (every) Sunday, (every) Monday, (every) Tuesday, etc.

Select the day or days of the week for the Timer to turn on the TV.

Time To set the time for the TV to come on:

With the hour highlighted, press 4. repeatedly to change the hour and the AM/ PM indicator. Press and hold to change the hour display quickly. Press 5.

ENTER

to highlight the minutes.

Press 6. t

Input Ant, DVD, VCR, etc.

Select the input you want displayed when the TV comes on. Choose from the defined and enabled inputs that appear in the Activity menu.

o change the minutes. Press and hold to change the minutes display quickly.

POWER

indicator on the front of the TV flashes

Channel

If the source is the hold to scroll through channels.

ANT

input, select a channel number by pressing or press and

In the U.S. call 1(877) 675-2224 for assistance.

44 4. TV Menus

Initial, continued

Channel

(Channel Management)

Notes on Scan and channel memorization

• Channelmemorizationmaytakeupto15minutes

to complete.

•

To stop channel memorization before completion,

press

• WhenwatchingTV,pressCH to move through

memorized channels.

•

To add a digital channel that does not appear in the

Edit menu without repeating channel memorization:

Ant Air, Ant Cable

Scan

Edit After channel scan, Edit lets you add and delete individual channels from memory.

CANCEL. Channels already added are retained

Look up the 1. physical channel number for

the new digital channel. See the website www.antennaweb.org for help.

Press 2.

ACTIVITY

You must perform a channel scan to receive digital channels. Scan searches for broad-

cast channels and adds them to TV memory. To start channel scan

Highlight one of the input selections based on your connection to the1.

Air• when connected to an indoor or outdoor antenna. Cable• when connected to direct cable (no cable box)

Press 2. to highlight SCAN. Press 3.

ENTER

to start channel memorization.

• Press

• Press to move through all channel numbers, one at a time.

and select the

ENTER

to add or remove checks.

PAGE DN/UP

ANT

to jump to the next or previous page of channel numbers.

input.

ANT input

Use the number keys and 3.

the physical channel number followed by “-1” and

ENTER

. For example, for physical channel

36, press

The TV will search for a digital channel on the channel 36 frequency. When it finds the channel, it will:

Rememorize channels if you move the TV to a differ-•

ent geographic area with a different channel line-up.

3 6

a. Add the channel to memory. b. Change the channel number to the virtual

channel number sent by the broadcaster.

c. Add to memory any associated sub-

channels.

CANCEL

ENTER

key to enter

Adding/Deleting Channels Using the Channel Edit Menu

Channels marked with a check are in memory.• To add or delete a channel from • memory, highlight the channel number and press To add a single digital channel not in the list, see the notes under • Scan on this page. Digital channels are listed by virtual channel number with the physical channel number shown in small gray text. • See below for an explanation of these terms.

Virtual - Channel Number (digital channels only). A channel number sent by a local broadcaster. Usually the virtual number is associated with the corresponding analog channel number. For example, a broadcaster may associate digital channel 2-1 with their analog channel 2. Physical Digital Channel Number. - The channel number officially assigned to the actual broadcast frequency; shown on screen in gray text.

Energy Energy

Usage

Standard, Fast Power On

Options for power consumption while the TV is powered off.

Standard• keeps the TV’s energy use within ENERGY STAR® guide- lines while powered off.

Fast Power On• lets the TV power up quickly. The TV uses power while in the off state in excess of ENERGY STAR guidelines for a powered-down device.

In Canada call 1(800) 450-6487 for assistance.

ENTER

4. TV Menus 45

Inputs

Name

General Notes

When you change an input name in the Name menu and then exit the Name menu:

The name is changed• The icon in the • Activity menu is changed Audio and video settings are changed to the defaults for the new device type.•

L75-A91.• All previous NetCommand IR “learning” for the input is erased.

Cablebox, Cam(corder), CD, DVD (DVD, DVD2, Blu-ray), DVR, Game (Game, PS, Xbox, Wii), MP3 Player, PC, Satellite, VCR, AVR

Delete (deactivated HDMI only) On/Off (ANT only)

Lets you assign or • change names of inputs appearing in the Activity menu.

Press - to move between inputs. Press - to select a name. You cannot change the name of the current input; you must first switch to another input. If you have only one input, such as a cable box, make sure the Ant input is On and switch to Antenna in the Activity menu before

renaming the single input. Lets you turn the • Ant input On/Off (to display/hide it in the Activ- ity menu). Lets you delete unused HDMI inputs from the • Activity menu. A CEC-enabled tuner can be named either •

Satellite

A CEC-enabled DVD player can be named •

Blu-ray. L75-A91.• The VUDU™ icon always remains visible.

Cable Box

DVD, DVD2

, or

Notes for HDMI devices

Disconnecting an HDMI device:• When you disconnect an HDMI device, the icon remains in the Activity menu until

you remove it. Select Delete in the Inputs > Name menu to remove an unwanted icon for an HDMI input. If the • New Device Found screen does not display as expected when you connect an HDMI device, see “Reac-

tivating Auto Input Sensing for an HDMI Input,” page 13.

HDMI Control and CEC-Enabled Devices:• See Appendix C, “HDMI Control of CEC Devices,” page 73. In case of CEC conflicts:• Turn off CEC signals in one of these ways:

Turn off the TV’s HDMI Control signals to the device. Turn off each device’s internal CEC capability. -

See Appendix C for the TV’s HDMI Control or, to turn on/off a specific device’s response to CEC signals, see the device owner’s manual.

L75-A91. Sets up or changes NetCommand IR control of the current viewing device.

Learn

AVR

HDMI Control On, Off Select On or Off to enable or disable the TV’s control of a CEC-enabled device. See

See “About NetCommand IR Control,” page 50.

L75-A91. Sets up or changes NetCommand IR control of an A/V receiver. See “NetCommand IR Control of an A/V Receiver” on page 56.

Appendix C for use of this feature.

Activity Lets you • customize the Activity menu choices for the current input.

Highlight the activity name and press • See • “How is the Activity Menu Generated?” on the next page.

ENTER

to make changes.

In the U.S. call 1(877) 675-2224 for assistance.

46 4. TV Menus

Inputs, continued

How is the Activity Menu Generated?

The TV automatically generates the Activity menu based on recognized inputs. If the inputs have been named as device types, the TV groups the device types based on how they can be used. The device names used for groupings are those assigned in the New Device Found menu or the Inputs > Name menu. The table below summarizes the device groupings that can appear in the Activity menu.

Key

Activity assignments made automatically by the TV.

X Activity assignments you can make using the

Inputs > Activity menu.

Antenna

AV Receiver

Blu-ray

Cable Box

Camcorder

CD/Au dio

DVD

DVD2

DVR

Game

MP3 Player

Satellite

USB

VCR

VUDU

(L75-A91)

Wii

Xbox

Watch TVWatch

Movie

Play

Game

View

Photos

  



X X



 



 



 

X X



 

X X

Listen Music



In Canada call 1(800) 450-6487 for assistance.

4. TV Menus 47

Lock

TV Locks

Parental

Time Lock by Time

Panel Lock Control Panel

Other

Lock by Program Ratings

Restricts access using U.S.-based ratings sent by broadcasters. Available on model L75-A91 (U.S. only).

Restricts TV use by time of day.

Disables the buttons on the TV’s control panel. Use this option if small children in the home try to press control-panel buttons.

Lock by Other Program Ratings

Restricts access using non-U.S.-based ratings sent by broadcasters. model L75-A91 (U.S. only).

Available on

Pass Codes

Setting a Pass Code

You are prompted to enter a pass code whenever you select Lock on the main menu. To set a pass code for the first time:

Press 1.

and highlight Lock. A screen prompt-

ing you for a pass code will display. Input a four-digit pass code using the number keys 2.

on the remote control.

Press •

CANCEL

back one space. Press •

setting a pass code.

Press 3.

ENTER

Resetting a Pass Code

See the procedure in Appendix B.

Important Notes on Rating Locks

•

Parental menu rating locks apply only to channels and signals received on the ANT posite

• Other nels received on ANT

• Whenviewingacablebox,satellitereceiver,

or other device connected to the component

Y Pb Pr

owner’s guide for parental locks.

VIDEO

menu rating locks apply only to digital chan-

to delete a number and move

BACK

to close the menu without

to set the pass code.

jacks.

HDMI

inputs, check the device’s

and com-

Parental Menu

Model L75-A91, U.S. Only

The TV comes from the factory with the rating locks turned off and with pre-set U.S. ratings TV-PG and movie rating PG. Turn on blocking for U.S. ratings to activate these rating restrictions. Use the Lock > Parental menu to change the level of blocking with U.S. ratings.

Any time you change the channel or device, it may take up to five seconds for the rating restrictions to take effect.

To set parental controls for VUDU™ service, use the VUDU Info & Settings menu. The TV’s Parental menu does not control content accessible through VUDU.

Other Menu (Alternate Rating System)

Model L75-A91, U.S. Only

This TV can recognize new rating systems that may come into effect in the future. The Other menu allows you to block digital programming when such systems come into effect.

The first time you tune to a channel broadcasting an alternate rating system, the TV defaults to the most restrictive setting if the Lock menu > Other Lock option is set to On. Use this menu to change the allowed rating if you are unable to watch a program rated with an alternate system.

Bypassing TV Locks

If you try to watch a blocked program or the TV is • locked by time, a notice will appear prompting you for a pass code. To use the TV, input your four-digit pass code and press

To reactivate the locks after using a pass code, power the TV off and then on. To reactivate only the parent ratings lock, change to a different channel or device.

If a program is blocked, you can still use the TV • without entering a pass code. Change to a channel airing an allowed program or change to another device.

ENTER

In the U.S. call 1(877) 675-2224 for assistance.

48 4. TV Menus

Lock, continued

Parental

Model L75-A91, U.S. Only

Lock Off, On

Start Time

Stop Time

TV Rating

FV Fantasy Violence. Applies to TV-Y7 only. D Sexual Dialog. Applies in differing degrees to TV-PG and TV-14.

S V Violence (graphic or realistic). Applies in differing degrees to TV-PG,

Movie Rating

Sets the time of day for enforcement of rating restrictions set in the Parental menu.

Highlight the hour digits for 1. Start Time. Press 2. repeatedly to change the hour and associated AM/PM indicator. You can also just press

and hold to move quickly through the numbers. Press 3. With the minutes digits highlighted, press 4. repeatedly to change the minutes. You can also just

press and hold to move quickly through the numbers. Highlight the 5. Stop Time digits and set the time as described above.

Note: To make rating restrictions active 24 hours a day, make Start Time and Stop Time the same.

TV-Y Yo u th. For children under 7. Highlight the rating level

TV-Y7 Youth 7 and older.

TV-G General Audience. For the entire family.

TV-PG Parental Guidance. Parental Guidance recommended; may

TV-14

TV-MA Mature Audience. For adults only.

Adult Language. A Sexual Situations. Applies in differing degrees to TV-PG, TV-14, and TV-MA.

TV-14, and TV-MA.

G General Audience. Designed for the entire family.

PG PG-13 Parental Guidance, 13 and Older. Not recommended for children under 13.

R NC-17 No Children 17 or Under. Restricted in theaters to 18 years old and older. X Adult. Designed for and restricted in theaters to adult audiences only.

Disables or enables blocking based on V-Chip signals and the U.S. rating system.

ENTER

to highlight the minutes.

not be suitable for some children.

Adolescent 14 and older. Not recommended for children under 14.

pplies in differing degrees to TV-PG, TV-14, and TV-MA.

Parental Guidance. Parental Guidance recommended; may not be suitable for some children.

Restricted. Restricted in theaters to 17 years old and older unless accompanied by an adult.

you wish to change and press

ENTER

to block it

( ) or allow it ( ).

You can apply supplemental content blocking to the age-based ratings by using the TV content categories listed below.

TV Content

Categories

Not Rated No MPAA rating assigned

In Canada call 1(800) 450-6487 for assistance.

4. TV Menus 49

Lock, continued

Blocks all use of the TV during the time period you specify. You must enter a pass code to use the

Time

TV when the time lock is in effect.

Lock by Time

Lock Time, Unlock Time

Enables/disables Lock by Time. To set the lock and unlock times:

Highlight the hour digits for the 1. Lock Time. Press 2. repeatedly to change the hour and associated AM/PM indicator. To

move quickly through the numbers, just press and hold. Press 3.

ENTER

to set the hour and highlight the minutes.

With the minutes highlighted, press 4. repeatedly to change the minutes. To move quickly through the numbers, just press and hold.

Highlight the 5. Unlock Time digits and set the time as described above.

Panel

Other

Note: T

Off, On On locks and Off unlocks the buttons on the TV’s control panel. Use this option if

small children try to press TV buttons.

Other Menu Options (alternate rating system) Model L75-A91, U.S. Only

This TV can recognize new rating systems that may come into effect in the future. The Other option remains grayed out until the TV receives a signal using an alternate rating system. Such alternate rating systems will apply only to digital programming received on the

Lock On, Off Enables/disables program blocking.

System Name Group Rating groups available in the rating system shown on the screen. Rating groups are

Rating Rating restrictions available in the selected rating system and group. Highlight the

The rating system available for the channel

defined by the rating system in effect.

rating and press

o make Lock by Time active 24 hours a day, make Start Time and Stop Time

the same.

To • release the Panel Lock from the TV’s control panel, press and hold the

ACTIVITY

lock releases to make the TV power on. To reactivate the lock, return to this menu and change the setting to • On.

button for ten seconds. If the TV is powered off, press

ANT

input.

ENTER

to check (block) or uncheck (allow) rated content.

POWER

after the

In the U.S. call 1(877) 675-2224 for assistance.

NetCommand IR Control

About NetCommand IR Control

NetCommand IR home-theater control is avail-• able on model L75-A91.

NetCommand IR home-theater control setup is • optional.

You can perform NetCommand setup when the TV • first recognizes a device during Auto Input Sensing or at any convenient time afterward.

NetCommand operates by sending remote control • signals from the TV to your other devices via the IR (infrared) emitters, telling the devices to play, record, change inputs, adjust volume, change channels, or perform other functions. All this is accomplished with the TV’s remote control left in TV mode.

You may wish to use NetCommand IR control to • supplement control of CEC-enabled devices.

Important Note on NetCommand

Be sure to connect the IR emitter cable to the TV and properly place the emitters so that NetCommand can control your devices.

In Canada call 1(800) 450-6487 for assistance.

5. NetCommand IR Control 51

DIGITAL

SURROUND

A/V Receiver

Other A/V Device

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

IR-

NetCommand

Output/External

Controller Input

IR-

NetCommand

Output/External

Controller Input

On top of a single tall device

IR sensor

In front of a single

average-sized device

On top of a single tall device

In front, shared by two average-sized

devices

IR sensor

IR Emitter Placement

The NetCommand system uses emitters connected

to the IR– devices such as DVD players, cable boxes, satellite receivers, and VCRs.

Replacement IR emitter cables are available for purchase from Mitsubishi. Request either part

number 242D483020 (two-ended cable) or part number 299P254020 (four-ended cable).

NetCommand Output

jack to control other

Connect the plug end of the IR emitter cable to the

IR—NetCommand Output

When the leave

Highlight

New Device Found screen displays,

IR—NetCommand Output selected.

EXIT and press

jack on the TV back panel.

ENTER

The New Device Found screen displays when you

connect the IR emitter cable.

Position the emitter end with the emitter bulb facing

the device’s remote control sensor. The bulb emits infrared light in a cone-shaped pattern. Place the bulb far enough from the sensor to allow the cone pattern to reach the sensor.

In some cases, the emitter works better facing downward from the top of the device. Experiment to find what works best.

Secure the emitter ends in place using double-

sided tape. Place any unused ends behind the devices to

prevent stray signals from reaching the IR sensors.

IMPORTAN T

Position IR emitters so that each device’s sensor “sees” the signal from only one emitter. Otherwise, a device receiving signals from multiple sources (remote controls, IR emitters) may not respond at all.

Connecting IR–NetCommand Output

Place IR emitters so the signal can be “seen” by the IR sensor on each device.

If You are Unable to Locate a Device’s IR Sensor

The IR sensor is usually behind the plastic window •

of the front display panel. Using a flashlight, you

may be able to see it as a round or square cutout.

If you cannot see the sensor and the device’s • Owner’s Guide does not specify the location, do the following using the device’s remote control.

Starting at one end of the plastic window, hold 1.

the device’s remote control about one-half inch from the front of the device and press the

POWER

key.

If the device does not respond, move the 2.

remote control one inch toward the center and try again. Repeat until the device responds.

Repeat the previous steps starting at the other 3.

end of the window. The sensor will be between

these two points.

In the U.S. call 1(877) 675-2224 for assistance.

52 5. NetCommand IR Control

Initial NetCommand Setup

To perform this procedure, you need:

The remote controls for both the TV and the • device you want to control.

An IR emitter cable (included)•

Note: To set up an A/V receiver, see “Setting Up A/V

Receiver Control,” page 57.

Connect and position the IR emitters for the

devices you wish to control. See “IR Emitter Placement” on the previous page.

Set the

on the TV. Open the NetCommand

TV’s remote control to TV mode and power

Learn screen as follows:

If working from the • New Device Found screen after the device is first detected, highlight NetCommand and press Learn screen for the device.

If performing NetCommand setup at any time • after the device has been recognized through Auto Input Sensing:

a. Press b. Highlight the desired input icon and press

c. Press

ACTIVITY.

ENTER

to switch to that input.

, highlight Inputs, and highlight

Learn to open the Inputs > Learn screen

for the device.

ENTER

to open the

From the New Device Found screen, highlight NetCommand and press ENTER to open the Learn screen.

Device-specific keys in the rightmost column can be accessed with the MORE key after “learning.”

The first function highlighted in the

is always Power On. Aim the TV’s remote control at the TV and press function.

When the

device’s

key until a check mark appears next to Power On.

Press the

to highlight other keys on the list. Repeat steps 4 and 5 for each additional function you wish to control through NetCommand.

Note: Device keys in the far right column will be asso-

If the device has a separate

on the TV’s remote to highlight Power Off.

Repeat the earlier steps to “learn” the

If the device has no

Press

current device.

Power On

remote control at the TV and hold the POWER

If the text stops flashing before the check mark • appears, repeat the previous step.

To remove the key from NetCommand control, • press the highlighted.

keys on the TV’s remote control

ciated with the remote control’s “learned.” See the table on page 54.

BACK

to finish NetCommand “learning” for the

ENTER

to begin learning for that

text starts flashing, aim the

CANCEL

key while the key name is

POWER OFF

Learn screen

key when

key, press

POWER OFF

key, skip this step.

key.

Inputs > Learn screen

Key names marked with a check have been “learned.”

Adding or Removing Device Keys from NetCommand Control

Switch the TV to the device. Press

light the device’s icon, and press Open the

When the

Inputs menu and highlight the Learn icon.

Learn screen displays:

To add keys: • Continue as described earlier under “Initial NetCommand Setup” on this page.

To delete keys:• Highlight the name of the key you wish to delete and press TV‘s remote control to clear the check mark.

ACTIVITY

ENTER

CANCEL

, high-

on the

In Canada call 1(800) 450-6487 for assistance.

5. NetCommand IR Control 53

Operating NetCommand-Controlled Devices

Controlling Most Device Types

As an example of NetCommand control, if you are watching your cable box and you wish to tune to the next channel higher, press then sends the “learned” channel-up control signal to the cable box.

Perform NetCommand setup for the device as

described in this chapter. When you wish to use the device, press

Press

to highlight the icon for the device.

ENTER

to switch the TV to the device.

CHANNEL UP

. NetCommand

ACTIVITY

Special Operation Methods

Key Name in Learning Screen

Power On Manual Power On/Off

Special Operation Description and Setup How to Use

Use for devices that have only one

POWER

Note: if you have set up automatic input switching for

the A/V receiver, the A/V receiver will automatically switch to the correct input for the device.

To operate the device using the

key.

control, press the side button to put the remote control into TV mode.

Point the remote control at the

and press the key for the desired function. Press the

tions you may have “learned” for the device.

key to access additional key func-

Press 1.

ACTIVITY

Press 2. to highlight the icon for the device to be powered on or off.

With the 3. Activity menu still displayed, press

POWER

to send the power signal; you may

need to press

POWER

TV’s remote

TV (not the device)

twice.

Power On

Power Off

Menu Displaying a Menu for the Current Device

Guide Displaying the On-Screen Program Guide

Automatic Power On/Off

This feature is only for devices that have separate

POWER ON

remote controls. If your device does not have a separate Off learning position; use only the Manual Power ON/OFF method described above.

In the NetCommand Learn screen: a. “Learn” the Power On command in the

b. “Learn” the Power Off command in the

“Learn” the

Menu learning position.

(cable box or satellite receiver)

and

POWER OFF

Power On learning position.

Power Off learning position.

key on the original remote in the

“Learn” the 1. the Guide learning position.

Learn the 2. original remote in the Page Up and Page

Down learning positions.

GUIDE

PAGE UP

keys on their original

key, do not use the Power

key on the original remote in

and

PAGE DOWN

keys of the

Note: If you press

menu displayed, the TV will turn off.

Press 4.

ENTER

To Power On the Device•

Press 1. Press 2. to highlight the icon for

the device to be powered on or off. Press 3.

device and NetCommand will send the

Power On command to the device.

To Power Off the Device•

When you turn the TV off, the TV sends all learned Power Off commands to all devices.

Press

and then 1 to send the menu

command to the current device.

While watching the device, press 1. display the guide.

Press 2.

PAGE UP/DOWN

Up/Dn commands for the guide.

POWER

without the Activity

to switch the TV to the device.

ACTIVITY

ENTER

to switch the TV to the

GUIDE

( ) to send the Page

In the U.S. call 1(877) 675-2224 for assistance.

54 5. NetCommand IR Control

Operating NetCommand-Controlled Devices, continued

Key Name in Learning Screen

Enter ENTER-Key Functions (cable boxes, satellite receivers, etc.)

Enter (digits)

Cancel CANCEL as the Cancel or Exit Function

— (separator)

Special Operation Description and Setup How to Use

Some devices have two keys that have “enter” functions. One key is for menus and is often labelled

SELECT

or OK. A second key is for use with number keys for direct channel selection. NetCommand

uses the same When

ENTER

when the original remote control uses the same key for menus and channel selection:

Learn the NetCommand Enter learning position.

When

ENTER

nal remote control has a separate this function):

Learn the the NetCommand Enter (digits) learning position. Use this learning position only if the original remote control has separate keys for Enter in menus and Enter for channel selection.

“Learn” the Cancel or Exit function in the NetCommand Cancel learning position

The symbol “—” can serve as the separator between a digital channel’s main and sub-channel digits, e.g., digital channel 12-1 (main channel is 12, sub-channel is 1).

“Learn” the channel separator function in the NetCommand – (separator) learning position.

ENTER

key for both operations.

has a menu or guide function or

ENTER, SELECT,

is for channel changes, i.e., the origi-

ENTER

key for channel selection in

or OK key in the

ENTER

key for

Press 1. menu or guide.

Press 2. NetCommand will send the Enter signal for menus.

Press digit key(s) and then press NetCommand will send the Enter signal for channel selection.

Press 1. guide.

Press 2. the Cancel or Exit signal.

Press digit key(s) and press NetCommand will send the channel-separator signal.

GUIDE

ENTER

within the menu and

GUIDE

CANCEL

and NetCommand will send

to display the device’s

ENTER

to display the menu or

CANCEL

The MORE Key Menu and NetCommand

Perform NetCommand setup for these device-specific keys and then access their functions with the

Device Key

Input

SP/EP

List

On Demand

VCR

Cable/

SAT

DVD/

DVR

key.

A/V

In Canada call 1(800) 450-6487 for assistance.

Receiver

Device Key

Top Menu

Angle

Audio (DVD)

Subtitle

Repeat

Bonus View

Setup

Surround

Night

VCR

Cable/

SAT

DVD/

DVR

A/V

Receiver

5. NetCommand IR Control 55

Operating NetCommand-Controlled Devices, continued

NetCommand Specialized Device Keys

Refer to this chart when “learning” device keys. “Learn” some, all, or none of the keys used for each device type.

See page 53 for more on keys marked in the “Special Operation Method” column.

Key Name in Learning Screen

Power On Power On or Power ON/OFF (toggle)

Guide On-Screen Program Guide or DVD Disc Menus

Channel +/Skip + Next Channel Higher/

Channel –/Skip – Next Channel Lower/

Page Up Page Up in Guides

Page Dn Page Down in Guides

Up Arrow up

Down Arrow down

Left Arrow left

Right Arrow right

Enter Enter or Select (menus)

Cancel Cancel or erase (menus)

Play Start playback

Function

Skip Forward (Disc)

Skip Backward (Disc)

Name on TV Remote Control

See Special Operation Method Table



 

Stop Stop playback

Forward Fast Forward

Rewind Rewind/Fast Reverse

Pause Pause playback

Record Start Recording

1, 2, 3, 4, 5, 6, 7, 8, 9, 0 Digits

Enter (digits) Use after entering digits to tune directly to a

channel by number

- (separator) Add digital channel separator between main channel number and sub-channel number

Last Last Channel Recall

Info On-screen status display or information display May require two

Power Off Power Off

1, 2, 3, 4, 5, 6, 7, 8, 9, 0



keypresses



In the U.S. call 1(877) 675-2224 for assistance.

NetCommand IR Control of an A/V Receiver

NetCommand IR home-theater control is available on model L75-A91.

Several types of A/V receiver control can be set up using the Inputs > AVR menu.

Power and volume.• See the opposite page. Audio switching.• For most equipment setups, see

“Case 1: Automatic A/V Receiver Switching to the TV Audio Input” page 58.

Audio switching and surround sound.• To set up switching to a surround sound device, see “Case 2: Automatic A/V Receiver Switching to a Surround Sound Device” page 59

Audio and video switching over HDMI• . If your A/V receiver has an HDMI output, it may be convenient to send audio and video to the TV over a single HDMI cable through the A/V receiver. See “Case 3: Automatic Audio and Video Switching via HDMI,” page 60.

Note: To set up control of other device types, see

“Initial NetCommand Setup,” page 52.

Controlling an A/V Receiver after NetCommand Setup

Switching Audio to and from the A/V Receiver

Press

Controlling A/V Receiver Power

With Any Connection Type

and then Press Press

Press Press Press In many setups, the A/V receiver will power on

automatically when selected. If not, while the onscreen display is showing, point the remote control at the TV (not the A/V receiver) and press power the A/V receiver on or off.

to show the Speakers option.

to select either AV Receiver or TV.

and then

to show the Speakers option.

to select AV Receiver.

(AUDIO)

POWER

With an HDMI Connection

Press

Controlling Other A/V Receiver Functions

With the A/V receiver powered on and selected, the TV’s remote control operates the volume and mute functions. Also, when you switch to a device in the Activity menu, the A/V receiver automatically switches to the correct audio input for the device.

ACTIVITY

Highlight the A/V receiver icon. Press

POWER

In Canada call 1(800) 450-6487 for assistance.

6. NetCommand Control of an A/V Receiver 57

Setting Up A/V Receiver Control

Power and Volume

Perform this setup to control the A/V receiver power and volume with the TV’s remote control.

To perform this setup you need:

The remote controls for both the TV and the • A/V receiver. An IR emitter cable (included).•

Before You Begin

Connect your A/V receiver to the TV and any addi-

tional devices. See “Setting Up TV Inputs,” page 12 and “TV Connections,” page 18.

Connect the IR emitter cable to the TV and position

the IR emitter where it can send signals to the A/V receiver. See “IR Emitter Placement,” page 51.

Set the

side button.

Setup to Control A/V Receiver Power and Volume

Open the

The first function highlighted in the

always Power. Aim the TV’s remote control at the TV and press

To hear audio sent from the TV to the A/V receiver, you must have:

Physically connected the TV to the A/V • receiver. Connection can be via the analog or digital audio output or over HDMI.

Assigned the name AVR if using an HDMI A/V • receiver that was not recognized automatically.

“• inputs.

Assigned the TV’s audio output to the correct • input in the NetCommand Inputs > AVR menu.

Selected the A/V receiver as the audio source. • Press MORE then 9 (AUDIO), then the Speakers option, Receiver.

TV’s remote control to TV mode using the

Inputs > AVR screen in one of two ways:

If using the • New Device Found screen for the A/V receiver, highlight NetCommand and press

ENTER

to open the AVR screen.

If performing NetCommand setup at any time • after Auto Sensing:

Press

, highlight Inputs, and highlight AVR

to open the AVR menu.

AVR screen is

ENTER

to begin learning for Power.

IMPORTAN T

Learned” the IR codes for the A/V receiver

to show

then

to select the A/V

Inputs > AVR screen. Perform NetCommand IR “learning” for A/V receiver power and volume keys.

When the

receiver’s remote control at the TV and hold the

POWER

next to Power.

Press the 4. key on the TV’s remote control to highlight other keys in the list. Repeat steps 2 and 3 for each additional function you wish to control through NetCommand.

If the A/V receiver has a separate

press on the TV’s remote to highlight Power Off. Repeat steps 2 and 3 to “learn” the

If the device has no

When finished “learning” the power and volume

keys, either

Power text starts flashing, aim the A/V

POWER ON

If the text stops flashing before the check mark • appears, repeat this step.

To remove the key from NetCommand control, • press the highlighted.

To watch TV, press • To continue with NetCommand setup to control • switching of A/V receiver inputs, highlight NEXT and press

key until a check mark appears

CANCEL

key while the key name is

POWER OFF

BACK

ENTER

key, skip this step.

key,

key.

In the U.S. call 1(877) 675-2224 for assistance.

58 6. NetCommand Control of an A/V Receiver

audio + video

Incoming Coaxial Cable to TV’s ANT input

A/V Receiver

DVD audio

input

TV audio input

TV audio

out

audio output from TV (digital or analog)

video

analog audio

VCR with

Analog Audio Output

Setting Up A/V Receiver Control, continued

Automatic Audio or Audio/Video Switching

The following setups enable the A/V receiver to switch automatically to the correct input when you select a device in the TV’s Activity menu.

Three different connection arrangements are described here. Review the descriptions to find the setup needed for your equipment.

To hear digital surround sound from a source device you must use the setup described for Cases 2 or 3

To set up control of an A/V receiver you need:

The remote controls for the TV and A/V receiver.• An IR emitter cable available from Mitsubishi.• Connecting cables•

Before You Begin

Connect your A/V devices to the TV and connect

your A/V receiver to the audio outputs on the TV and the DVD player. Note the name of the device connected to each A/V receiver input. See initial setup, page 12, and “TV Connections,” page 18.

Position NetCommand IR emitters as described in

“IR Emitter Placement,” page 51. Set the TV’s remote control to

side button. Open the

and press menu.

Case 1: Automatic A/V Receiver Switching to the TV Audio Input

Most devices are set up to use the TV’s audio output like the VCR in this example; analog audio from the device is sent through the TV to the A/V receiver’s TV audio input.

Inputs > AVR menu, highlight NEXT

ENTER

to display the device-key-learning

mode using the

Important:

audio output to the A/V receiver’s TV audio input jack.

To use this setup, you must connect the TV’s

In the

Inputs > AVR > NEXT menu, press to highlight TV audio out as the A/V receiver input to control.

Press

ENTER

on the TV’s remote control.

While the text hold the control.

When a check appears next to release the

If the text stops flashing before the check mark • appears, repeat this step. To erase the IR code just “learned,” press •

CANCEL

Press

if you want to control surround sound switching for another audio source.

TV audio out is flashing, press and

TV INPUT

key on the A/V receiver’s remote

TV audio out,

TV INPUT

while the name is highlighted.

if finished or continue with Case 2 setup

key.

Use this setup for:

Audio Available from TV only. • Send audio from the

ANT

input to the A/V receiver from the TV’s

analog or digital audio output. Use this setup to make the A/V receiver switch to its

designated TV audio input when viewing programming from the

Analog Stereo Audio. •

analog stereo output (such as a VCR) can be sent either directly to the A/V receiver or through the TV first.

Mitsubishi recommends you send audio through the TV as shown in the example. The TV converts analog audio to digital format to send to a digital A/V receiver.

HDMI Digital Stereo Audio. • Digital stereo audio from an HDMI connection is available both in digital and analog format from the TV’s analog and digital audio output jacks.

In Canada call 1(800) 450-6487 for assistance.

ANT

input.

Audio from sources with only

Case 1: NetCommand setup for controlling A/V receiver switching to the A/V receiver’s audio input from the TV. The list displayed represents inputs in use. The device names are those you assigned in the New Device Found screen or in the Inputs > Name menu.

IMPORTAN T

All audio from what you are watching on the TV is always available from both the TV’s AVR AUDIO OUTPUT and DIGITAL AUDIO OUTPUT jacks.

To use the digital surround sound capabilities of your A/V receiver however, you must connect the audio output from your DVD player, satellite receiver, or cable box directly to the A/V receiver.

6. NetCommand Control of an A/V Receiver 59

A/V Receiver

DVD audio

input

DVD Player with

Digital Surround Sound

video

digital surround sound

DVD Player

with

Digital

Surround

Sound

Setting Up A/V Receiver Control, continued

Case 2: Automatic A/V Receiver Switching to a Surround Sound Device

Note: Use this setup to send digital surround sound from a source device directly to your external sound system. For non-surround sound source devices, Mitsubishi recommends using the setup for Case 1, in which audio is sent through the TV.

A device can send digital surround sound such as Dolby Digital or DTS directly to the A/V receiver. The device might be a DVD player, cable box, or satellite receiver, and could have HDMI output. A DVD player is used in this example.

Your setup may include additional devices with digital surround sound connected directly to the A/V receiver. These devices might be a DVD player plus a cable box or satellite receiver. Inputs already connected to the TV will appear listed in the setup screen.

Case 2: A/V receiver audio from a device providing surround sound directly to the A/V receiver

In the

Inputs > AVR > NEXT menu, press

to highlight the name of the A/V receiver input to control. In this example, it is the DVD input.

Press

ENTER

on the TV’s remote control.

Case 2: NetCommand setup for controlling A/V receiver switching to the A/V receiver’s DVD input. The list contains connected inputs with names assigned during Auto Input Sensing.

While the text

DVD INPUT

When a check appears next to

DVD INPUT

DVD is flashing, press and hold the

key on the A/V receiver’s remote control.

DVD, release the

key.

If the text stops flashing before the check mark • appears, repeat this step. To erase the IR code just “learned,” press •

CANCEL

If finished, highlight

while the name is highlighted.

EXIT and press

ENTER

or continue to set up additional A/V receiver audio sources.

Combining Setup Types Your setup can include devices connected using the Case 1 method plus other devices connected using the Case 2 method.

In the U.S. call 1(877) 675-2224 for assistance.

60 6. NetCommand Control of an A/V Receiver

A/V Receiver

HDMI Output

digital surround sound

HDMI Cable

Blu-ray player

DVD player

Cable box

VCR

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

HDMI

OUT

A/V receiver with HDMI output

Any connection types (can be HD or SD video)

AUDIO

DIGITAL

AUDIO IN

VCR

Cable box

DVD player

DIGITAL

AUDIO

OUTPUT

DIGITAL

AUDIO

OUTPUT

AVR AUDIO OUTPUT

Optional audio

connection

(analog or digital)

HDMI cable

Setting Up A/V Receiver Control, continued

Case 3: Automatic Audio and Video Switching via HDMI

If your A/V receiver has an HDMI output, it may be convenient to route video signals from multiple devices over a single cable to the TV. Use this procedure to set up NetCommand control of the A/V receiver’s audio and video switching over a single HDMI cable. The connected source devices can be analog, digital, or a mixture or the two. When this setup is complete, you can use the TV’s Activity menu to select a video device connected to the A/V receiver.

Before You Begin

To complete these steps you will need:

The remote controls for both the TV and the A/V • re ceive r.

An IR emitter cable (included)• An HDMI-to-HDMI cable to connect the A/V •

receiver to the TV and cables necessary to connect devices to the A/V receiver.

Connect the A/V receiver to the TV with an HDMI-to-

HDMI cable. Do not connect the optional audio cable at this time.

If desired, enable HDMI Control of a CEC-enabled

A/V receiver. See Appendix C, “HDMI Control of CEC Devices.”

Connect your audio/video devices to the A/V receiver.

Note the name of the device connected to each A/V receiver input. This information will be needed later to set up NetCommand’s automatic input switching.

More About Using an HDMI Connection

Audio from devices connected directly to the TV can • be heard from the TV speakers only. To send audio to the A/V receiver from such devices, use one of the optional audio connections shown in the diagram on this page. For example, use an optional audio connection if you wish to use the A/V receiver speakers to hear audio from:

The - ANT input A game or camcorder -

To use NetCommand to supplement HDMI control of •

Connect the HDMI cable.1. Enable HDMI control (2. New Device Found screen). Connect the secondary digital audio cable, if 3.

a CEC-enabled A/V receiver, the recommended setup sequence is:

desired. Perform NetCommand setup.4.

If you connect to HDMI after performing NetCommand setup for the A/V receiver, the NetCommand setup will be lost.

In some cases, audio from a device connected to the • A/V receiver may not be passed over the HDMI cable to the TV speakers. In these cases you must use the A/V receiver speakers to hear audio.

In Canada call 1(800) 450-6487 for assistance.

Multiple video inputs through a single HDMI cable. You can connect multiple video devices to an A/V receiver that has an HDMI output. The optional audio connection allows you to hear, through the A/V receiver, devices connected to the TV only, e.g., an antenna on the

ANT

input.

6. NetCommand Control of an A/V Receiver 61

Setting Up A/V Receiver Control, continued

If using an optional audio cable between the TV and

A/V receiver, connect it. Connect the IR emitter cable to the TV and position

the IR emitter where it can send signals to the A/V receiver. See “IR Emitter Placement,” page 51.

NetCommand Control of a Device Connected to an HDMI A/V Receiver

Use this setup to have NetCommand control a device sending audio and video through the A/V receiver to the TV via HDMI.

Setup to Control Automatic Audio and Video Switching via HDMI

When this setup is complete, the “learned” A/V receiver input will appear in the TV’s Activity menu as a selectable input.

Power on the A/V receiver.

Set the

side button. Power on the TV.

When the

select device name AVR if it is not recognized automatically.

Navigate to the

within the New Device Found screen, highlight

NetCommand and press

TV’s remote control to TV mode using the

New Device Found screen displays,

Inputs > AVR menu or, from

ENTER

You must have already completed the procedure under “Setup to Control Automatic Audio and Video Switching via HDMI” on this page. That procedure placed an icon in the Activity menu for the device (input) connected to the A/V receiver.

Any Connection

Type

Source

Device

Set up NetCommand control of A/V receiver audio/

video switching via HDMI as described on this page.

Press

BACK

to close any open menus and return to

normal TV viewing. Press

ACTIVITY

Highlight the icon for the A/V receiver input you wish to control.

Press

ENTER

and the A/V receiver to the input. Open the Perform NetCommand “learning” for the con-

nected )device by following the steps in “Initial NetCommand Setup,” page 52.

to switch the TV to the A/V receiver

Inputs > Learn menu.

A/V

Receiver

HDMI Cable

To set up A/V switching over HDMI, choose your devices from a list. Unlike the device list described for Case 2, this is a generic list containing more than just the devices detected in your setup.

In the

10.

Inputs > AVR > NEXT menu, press

to highlight the name of the A/V receiver input to control. In this example, it is the DVD input.

Press

ENTER

on the TV’s remote control.

While the text

DVD INPUT

When a check appears next to

DVD INPUT

If the text stops flashing before the check mark • appears, repeat this step. To erase the IR code just “learned,” press •

CANCEL

If there are no more devices to set up, highlight EXIT and press tional A/V receiver audio/video sources.

DVD is flashing, press and hold the

key on the A/V receiver’s remote control.

DVD, release the

key.

while the name is highlighted.

ENTER

or continue to set up addi-

In the U.S. call 1(877) 675-2224 for assistance.

In Canada call 1(800) 450-6487 for assistance.

Appendices

Appendix A: Programming the Remote Control ........... 64

Appendix B: Bypassing the Parental Lock .............. 71

Appendix C: HDMI Control of CEC Devices .............. 73

Appendix D: TV Care ........................... 76

Appendix E: Troubleshooting ...................... 77

In the U.S. call 1(877) 675-2224 for assistance.

64 Appendices

GUIDE MENU INFO BACK

ACTIVITY

Appendix A: Programming the Remote Control

This appendix explains programming the TV’s remote control to operate other A/V devices. This is distinct from NetCommand and HDMI control.

Functions Available for Other A/V Devices

The TV’s remote control can be programmed to operate other types and brands of A/V products. The functions performed in each switch position vary depending on the product. Not all functions work for all models. The most common functions available are listed on this page.

Control modes

To use the remote after programming, press the side button to change the control mode to match the device type.

The MORE Menus

The

key displays a menu showing additional key functions available for a device after programming the remote control for the device type.

L75-A91 Supplemental Keys

The supplemental cable box keys may provide additional controls. Program the remote control for your cable box and test the keys.

The TV’s remote control may operate the Favorites and On Demand features of your cable box.

The F1–F4 keys work like the A, B, C,

buttons on some cable boxes.

IMPORTAN T

Some manufacturers may change their products or they may use more than one remote control system. The TV’s remote control may be unable to operate your A/V equipment in these cases.

VCRs and DVRs

•

CHANNEL UP/DN

•

POWER

•

SLEEP (from

• (

FAST FORWARD PAUSE PL AY

MORE menu)

)

• (

•

GUIDE

•

0–9

RECORD REVERSE STOP

)

(DVR only)

Number Buttons

Mitsubishi VCRs are compatible with some additional keys.

Cable Boxes and Satellite Receivers

(not all functions for all models)

•

PAGE UP/DOWN

•

CANCEL

•

CHANNEL UP/DN

•

ENTER

•

GUIDE

•

POWER

•

LAST (ENTER

; for chan-

nels on some models)

•

0–9

Number Keys

The record/playback keys:

• (

FAST FORWARD PAUSE

)

PL AY

) RECORD REVERSE STOP

)

Model L75-A91 Keys for Cable Boxes

FAV

•

ON DEMAND

•

F1–F4

•

A/V Receivers

•

MUTE

•

POWER

•

SLEEP (from

•

VOLUME

•

0–9

MORE menu)

Number Buttons

• DirectInputSelection

buttons: numbers and

LAST

(on some

Mitsubishi models)

CD Players

(not all functions for all models)

•

SLEEP (from

• (

FAST FORWARD PAUSE PL AY

MORE menu)

)

• (

•

0–9

REVERSE STOP

)

Number Buttons

DVD Players

(not all functions for all models)

•

CANCEL

models)

•

CHANNEL UP/DN

track skip on some models)

•

ENTER

•

POWER

•

SLEEP (from

(on some

(for

MORE menu)

• (

•

0-9

Number Keys

FAST FORWARD PAUSE

)

PL AY

) RECORD REVERSE STOP

)

•

In Canada call 1(800) 450-6487 for assistance.

Appendices 65

Appendix A: Programming the Remote Control, continued

Programming the Remote Control

Press the side button on the remote control to

change to the correct mode for the product you want to control. Refer to the table below. Only one of each device type can be controlled in each mode.

Mode Available Device

CA B L E /SAT

VCR

DVD

AUDIO

Press and hold

several seconds until the mode indicator blinks twice and goes off.

Release the

Enter the first five-digit code listed for your equip-

ment.

The mode indicator blinks twice when you •

start to enter the code and then once for each additional keypress.

The mode indicator blinks twice when you finish •

entering a valid code. If you need to start over or wish to exit pro-•

gramming mode, temporarily change to a different mode using the side button.

Point the remote control at the equipment and

press

POWER

function, press a different key, such as (

(

STOP

If the equipment responds, the remote control • is properly programmed.

If the equipment does not respond, repeat • steps 2–4 with the next five-digit code listed for your equipment.

Once you have found the correct code, write it in

the space below for future reference.

Cable Box DTV Receiver Satellite Receiver

VCR DVR DVD Player/Recorder

DVD Player/Recorder DVR VCR

A/V Receiver Audio Amplifier CD Player

POWER

on the remote control for

POWER

key.

. If the product has no power on/off

VOLUME UP

, or

MUTE.

PL AY

Mode

CA B L E /SAT

VCR

DVD

AUDIO

You may need to reprogram the remote control after changing the batteries. Record the codes for each mode in the space provided to make this faster.

Code Verification

To determine the code programmed for any mode:

Set the mode to the one you wish to verify.

Press and hold

several seconds until the and goes off.

Press keys

Press

and count the blinks of the power key. Write down the number of blinks as the first digit of the code.

Repeat step 4 for the second, third, fourth, and fifth digits of the code.

Device Type Code

IMPORTAN T

POWER

on the remote control for

mode indicator

9 9 0

blinks twice

Audio Lock: Universal A/V Receiver Control

With Audio Lock enabled, the remote control operates volume and mute on the A/V receiver in all modes set by the side button. Activate Audio Lock if you always use an A/V receiver with your TV and other A/V equipment.

Program

described in “Programming the Remote Control” on this page.

With the remote control in

on the remote control for several seconds until the mode indicator blinks twice and goes off.

Press keys

The mode indicator will blink twice to indicate Audio Lock is active.

To Reset the Remote Control to Operate Volume and Mute for the TV Speakers

Press and hold

mode indicator blinks twice and goes off. Press keys

The mode indicator will blink four times to indicate Audio Lock has cleared.

AUDIO

mode for your A/V receiver as

AUDIO

mode, hold

9 9 3 ENTER

POWER

for several seconds until the

9 9 3 VOLUME UP

POWER

In the U.S. call 1(877) 675-2224 for assistance.

66 Appendices

Appendix A: Programming the Remote Control, continued

Programming Codes

Audio Ampliﬁers

Adcom 41100, 40577 Altec Lansing 41742 Bel Canto Design Bose 4 06 74 Carver 40892 Cary Audio Design Classe 41461 Flextronics 41879 Halcro 419 3 4 Harman/ Kardon JVC 40331 Krell 41837 Left Coast 40892 Lexicon 41802, 41145 Marantz 40892 Mark Levinson Parasound 41934 Philips 40892 Polk Audio 40892 Victor 40331 Yamaha 40354

Cable Boxes

A-Mark 10144, 10008 ABC 10237, 10008 Acorn 10237 Action 10237 Active 10237 Americast 10899 Amino 11822, 11602 Archer 10237 Bell South 10899 Century 10008 Cisco 11982, 11877, 10877 Comcast 119 82 Digeo 12187 Director 10476 GE 10144 General Instrument GoldStar 10144 Hitachi 10008 i3 Micro 116 02 Insight 10476 Jerrold 10476 Memorex 10000 Motorola 11376, 11254, 10476 Myrio 11822, 11602 Nova Vision 10008 Novaplex 10008 Pace 11877, 10877, 10237,

Panasonic 11982, 10144, 10008,

41583

41879

40892

41483

10476

10008

10000

Cable Boxes

Paragon 10525, 10008, 10000 Penney 10000 Philips 113 05 Pioneer 11877, 10877, 10533,

1014 4 Pulsar 10000 Quasar 10000 Runco 10000 Samsung 10144 Scientific Atlanta Sejin 116 02 Sony 110 06 Sprucer 10144 Toshiba 10000 US Electronics Videoway 10000 Zenith 10899, 10525, 10000

CD Players

Acoustic Research Akai 40083 Burmester 40420 California Audio Labs DKK 40000 Fisher 40000 Garrard 40420 Hafler 40173 Harman/ Kardon Inkel 40180 Integra 40101 JVC 41294, 40072 Kenwood

KLH 41711, 41318 Koss 41317 LG 41208 Magnavox 40038 Marantz 40626, 40435, 40180,

McIntosh 4170 3 MCS 40029 Memorex 40420, 40000 MGA 40083 Miro 40000 Mitsubishi 40098, 40083 Modulaire 40420, 40180, 40087,

MTC 40420 NAD 41208 Onkyo 41327, 40101 Optimus 40420, 40087, 40037,

Panasonic 40752, 40388, 40029

11877, 10877, 10477,

10237, 10008, 10000

10008

40420

40029

41202, 40173, 40100, 40083

40626, 40190, 40037, 40029, 40000

40038, 40029

40000

CD Players

Parasound 40420 Penney 40029 Philips 40626 Pioneer 41087 Proceed 40420 Quasar 40029 RadioShack 40420, 40180, 40000 RCA 40420 Realistic 40420, 40180, 40087,

40000 Roksan 40435 Rotel 40420 Sansui 40000 Sanyo 40087, 40000 Sharp 40180, 40037 Sherwood 41950, 40180 Sony 41364, 40490, 40185,

40100, 40000 Symphonic 40180 Tascam 40420 TDK 41208 Teac 40490, 40420, 40180 Techni c s 40029 Victor 40072 Wards 40087 Yamaha 41292, 40490, 40036 Yorx 40000

A/V Receivers

ADC 40531 Aiwa 41641, 41405, 41388,

41243, 40189, 40121 Alco 41390 AMC 41077 Anam 41609, 41074 Arcam 41189 Audiotronic 4118 9 Audiovox 4139 0 Bose 41933, 41841, 41629,

41253, 41229, 40639 Cairn 40189 Capetronic 40531 Carver 41289, 41189, 40189,

40121 Curtis Mathes Daewoo 41250 Denon 41360, 41306, 41142,

Emerson 40531 Fisher 41801 Grundig 40189 Harman/ Kardon Hitachi 41801 Insignia 42169, 41893, 41077,

40014

40121

41306, 41304, 41289,

40891, 40189, 40110

41030

In Canada call 1(800) 450-6487 for assistance.

Appendices 67

Appendix A: Programming the Remote Control, continued

Programming Codes, continued

A/V Receivers

Integra 41805, 41320, 41298,

40842 JBL 41306, 40110 JVC 42331, 41643, 41495,

41374, 41282, 41058 Kawasaki 41390 Kenwood 41570, 41569, 41313 KLH 41428, 41390 LG 42197, 41293 Linn 40189 Magnavox 41514, 41269, 41266,

41189, 40531, 40189 Marantz 41289, 41269, 41189,

40891, 40189 McIntosh 41289 Micromega 41189, 40189 Mitsubishi 41957, 41922, 41921,

41920, 41393 Myryad 4118 9 Nakamichi 41313 Onkyo 41905, 41805, 41320,

41298, 40842 Optimus 41074, 41023, 40531,

40121, 40014 Panasonic 42967, 41764, 41763,

41633, 41548, 41518,

41509, 41316, 41308,

41288, 41275 Philips 41269, 41266, 41189,

40891, 40531, 40189 Pioneer 41935, 41384, 41123,

41023, 40630, 40531,

40150, 40014 Polaroid 41508 Polk Audio 41289, 40189 Proscan 41254 RadioShack 416 09 RCA 41609, 41511, 41390,

41254, 41123, 41074,

41023, 40531 Realistic 41609, 40121 Revox 40189 Rio 41869 Samsung 41500, 41304, 41295 Sansui 41189, 40189 Sanyo 418 01 Sherwood 42169, 41905, 41077 Sherwood Newcastle Sonic Blue 418 69 Sony 41858, 41822, 41759,

Stereophonics Sunfire 41313 Teac 41390, 41074

42169

41758, 41658, 41622,

41558, 41441, 41382,

41258, 41131, 41058

41023

A/V Receivers

Techni c s 41518, 41308 Thorens 41189 Toshiba 41788, 41123, 40842 Venturer 41390 Wards 40189, 40014 Yamaha 41815, 41476, 41376,

41375, 41331, 41276,

41176, 41023, 40176 YBA 41921 Zenith 41293

Satellite Receivers

Bell ExpressVu Chaparral 10216 Crossdigital 1110 9 DirecT V 11856, 11749, 11640,

Dish Network System Dishpro 11775, 11505, 10775 Echostar 11775, 11505, 11170,

Expressvu 11775, 10775 Fortec Star 11821 Funai 1137 7 GE 10566 GOI 11775, 10775 Hitachi 11250, 10819, 10749 Houston 10775 HTS 11775, 10775 Hughes Network Systems Humax 11790, 11781 Innova 10099 JVC 11775, 11170, 10775 LG 11414 Magnavox 10722 Mitsubishi 1074 9 Netsat 1009 9 Panasonic 10701, 10247 Pansat 118 07 Philips 11749, 11442, 11142,

Proscan 10566, 10392 RadioShack 10775, 10566 RCA 11442, 11392, 11142,

Samsung 11609, 11442, 11377,

11170, 10775

11639, 11609, 11442, 11414, 11392, 11377, 11142, 11109, 10819, 10749, 10639, 10566, 10392, 10247, 10099 11775, 11505, 11170, 10775

10775

11749, 11442, 11142, 1074 9

10775, 10749, 10722, 1009 9

10855, 10775, 10566, 10392, 10143

11276, 11142, 11109

Satellite Receivers

SKY 100 99 Sony 11640, 11639, 10639 Thomson 10566, 10392 Tivo 11442, 11142 Toshiba 11749, 10790, 10749 UltimateT V 11640, 11392 Uniden 10722 Zenith 11856, 11810

VCRs

A-Mark 20278, 20046, 20037,

20000 ABS 21972 Accurian 20000 Admiral 20479, 20209, 20060,

20048, 20047, 20039 Adventura 20037, 20000 Aiko 20278 Aiwa 20124, 20037, 20000 Akai 20242, 20175 Alba 20278, 20209 Alienware 21972 Allegro 20039 America Action American High Amstrad 20000 Astra 20035 Audiovox 20278, 20038, 20037 Avis 20000 Bell & Howell Bell ExpressVu Broksonic 20479, 20209, 20184,

Calix 20037 Candle 20038, 20037 Canon 20035 Carver 20081, 20035 CCE 20278 Cineral 20278 Citizen 20479, 20278, 20209,

Classic 20037 Colortyme 20278, 20060, 20045,

Colt 20000 Craig 20047, 20037 Criterion 20000 Crosley 20081, 20035, 20000 Crown 20278 Curtis Mathes CyberPower 21972 Daewoo 20278, 20046, 20045,

20278

20081, 20035

20479, 20048, 20046,

20039, 20035, 20000

21944

20121

20037, 20035, 20000

20035

20432, 20278, 20162,

20060, 20035, 20000

20037

In the U.S. call 1(877) 675-2224 for assistance.

68 Appendices

Appendix A: Programming the Remote Control, continued

Programming Codes, continued

VCRs

Daytron 20278, 20037 Dell 21972 Denon 20081, 20042 DirecT V 20739 Dish Network System Dishpro 21944 Dual 20000 Durabrand 20039, 20038 Dynatech 20000 Echostar 21944 Electrohome

Electrophonic Emerald 20184, 20121 Emerex 20032 Emerson 21593, 20593, 20479,

Expressvu 21944 Fisher 20047, 20046, 20039,

Fuji 20035, 20033 Fujitsu 20000 Funai 21593, 20593, 20278,

Garrard 20000 Gateway 21972 GE 20060, 20048, 20035,

Gemini 20060 Genexxa 20278, 20037, 20000 GFM 21593 Go Video 20614, 20432 GOI 21944 GoldStar 20278, 20039, 20038,

Goodmans 20278, 20081, 20037,

Gradiente 20000 Granada 20081, 20042 Grundig 20081 Harley Davidson Harman/ Kardon Headquarter 20046 Hewlett Packard HI-Q 20047, 20035, 20000 Hitachi 20089, 20045, 20042,

Howard Computers HP 21972

21944

20209, 20060, 20043, 20037, 20000 20037

20278, 20209, 20184, 20121, 20043, 20037, 20000

20000

20037, 20000

20000

20037, 20035, 20000

20000

20081, 20075, 20038

21972

20037, 20035, 20000 21972

VCRs

HTS 21944 Hughes Network Systems Humax 21988, 21797, 20739 Hush 21972 Hytek 20047, 20000 iBUYPOWER Instant Replay Jensen 20067 JVC 21944, 20067 KEC 20278, 20037 Kenwood 20067, 20046, 20038 Kodak 20037, 20035 KTV 20000 LG 20038, 20037 Linksys 21972 Lloyd’s 20038, 20000 Loewe 20081 Logik 20000 Lumatron 20278 Luxor 20046 LXI 20067, 20042, 20037,

Magnasonic 20593, 20278, 20037,

Magnavox 21593, 20618, 20593,

Marantz 20081, 20038, 20035 Marta 20037 Matsui 20209, 20037 Matsushita 20162, 20081, 20035 Media Center PC MEI 20035 Memorex 20479, 20278, 20209,

Metz 20037 MGA 20060, 20043 Microsoft 21972 Mind 21972 Minolta 20042 Mitsubishi 20443, 20242, 20214,

Motorola 20048, 20035 MTC 20000 MTX 20000 Multitech 20039, 20000 NEC 20067, 20038 Nikko 20278, 20037

20739, 20042

21972 20035

20000

20563, 20081, 20048, 20039, 20037, 20035, 20000

21972

20162, 20048, 20047, 20046, 20039, 20037, 20035, 20000

20173, 20075, 20067, 20060, 20048, 20047, 20043, 20042, 20000

VCRs

Nikkodo 20278, 20037 Niveus Media Northgate 21972 Olympus 20162, 20035 Onkyo 20222 Optimus 21062, 21048, 20593,

Orion 20479, 20278, 20209,

Panama 20035 Panasonic 21062, 20616, 20614,

Penney 20162, 20081, 20067,

Pentax 20042 Philco 20479, 20209, 20081,

Philips 21181, 21081, 20739,

Pilot 20037 Pioneer 20162, 20081, 20067,

Polk Audio 20081 Portland 20278 Presidian 21593 Proscan 20060 Protec 20000 Pulsar 20278, 20039 Quarter 20046 Quartz 20047, 20046, 20035 Quasar 20162, 20035 RadioShack 20162, 20048, 20047,

Radix 20037 Randex 20037 RCA 20880, 20060, 20048,

Realistic 20278, 20162, 20121,

ReplayTV 20616, 20614 Ricavision 21972 Runco 20039 Salora 20075 Samsung 20739, 20432, 20060,

Sanky 20048, 20039

21972

20432, 20162, 20048, 20047, 20037, 20035, 20000

20184, 20121, 20000

20225, 20162, 20035, 20000

20047, 20042, 20038, 20037, 20035, 20000

20035, 20000

20618, 20616, 20209, 20162, 20081, 20048, 20045, 20035, 20000

20042

20046, 20037, 20035, 20000

20045, 20042, 20035, 20000

20048, 20047, 20046, 20037, 20035, 20000

20045, 20038, 20000

In Canada call 1(800) 450-6487 for assistance.

Appendices 69

Appendix A: Programming the Remote Control, continued

Programming Codes, continued

VCRs

Sansui 20479, 20209, 20067,

20000

Sanyo 20479, 20159, 20047,

20046, 20000

Scott 20184, 20121, 20045,

20043

Sears 20209, 20162, 20067,

20060, 20048, 20047, 20046, 20045, 20043, 20042, 20039, 20037, 20035, 20033, 20000

Sharp 20848, 20048, 20047,

20032, 20000 Shintom 20039, 20000 Siemens 20037 Signature 20479, 20060, 20048,

20046, 20037, 20035,

20000 Singer 20037 Sonic Blue 20616, 20614 Sonographe 20046 Sony 21972, 21032, 20636,

20067, 20047, 20046,

20035, 20033, 20032,

20000 Soundmaster Stack 9 21972 STS 20042 SV2000 20000 SVA 20000 Sylvania 21593, 20593, 20081,

Symphonic 21593, 20593, 20000 Systemax 21972 Tagar Systems Tandy 20000 Tashiko 20037 Tatung 20081, 20067, 20048,

Teac 20067, 20000 Techni c s 20162, 20037, 20035,

Teknik a 20037, 20035, 20000 Tevion 20479 Thomas 20000 Thomson 20060 Tisonic 20278 Tivo 21944, 20739, 20636,

TMK 20000 TNIX 20037 Toshiba 21988, 21972, 21008,

Tosoni c 20278 Totevision 20037

20000

20043, 20035, 20000

21972

20000

20618

20209, 20045, 20043,

20000

VCRs

Touch 21972 Trix 20037 Ultra 20278, 20045 Vector 20045 Vector Research Victor 20067 Video Concepts Videomagic 20037 Videosonic 20000 Viewsonic 21972 Villain 20000 Voodoo 21972 Wards 20479, 20081, 20060,

Wharfedale 20593 White Westinghouse World 20479, 20209 XR-1000 20035, 20000 Yamaha 20038 Zenith 21139, 20479, 20278,

ZT Group 21972

DVD and Blu-ray Players

3D LAB 30539, 30503 Accurian 31416, 30675 Acoustic Solutions Adcom 31094 Afreey 30698 Aiwa 30641, 30533 Akai 31089, 30770, 30705,

Alba 30717, 30672 Alco 30790 Allegro 30869 Amphion Media Works AMW 30872 Apex Digital 31061, 31056, 31020,

Arrgo 31023 Aspire Digital Astar 31489 Audiovox 31041, 30790, 30717 Awa 30730

20184, 20038

20242, 20045

20048, 20047, 20046, 20045, 20043, 20042, 20038, 20037, 20035, 20033, 20000

20479, 20278, 20209, 20000

20209, 20039, 20037, 20033, 20000

30730

30695

30872

31004, 30797, 30796, 30794, 30755, 30717, 30672, 30533

31168, 31407

DVD and Blu-ray Players

B & K 30662, 30655 BBK 31224 Bel Canto Design Blaupunkt 3 0717 Blue Parade 30571 Blue Sky 30699, 30695 Bose 32023, 31895 Brandt 30651 Broksonic 30695 California Audio Labs Celestial 31020 Centrex 31004, 30672 Cinea 30831 CineVision 30869, 30833 Citizen 32116, 31587, 31277,

Clairtone 30571 Coby 31351, 31177, 31165,

Craig 30831 Creative 30539, 30503 Curtis Mathes CyberHome 31537, 31502, 31129,

Cytron 30705 Daewoo 31242, 31234, 31172,

Dansai 30770 Daytek 30872 Decca 30770 Denon 32258, 30634, 30490 Denver 30778 Desay 31407 DigitalMax 31738 Digitrex 30672 Disney 31270, 30675 DiViDo 30705 Dual 31068, 30675 Durabrand 31127, 31023 DVD2000 30521 Electrohome 32116, 31003 Emerson 31268, 30675, 30591 Enterprise 30591 Entivo 30539, 30503 Enzer 30770 ESA 31268 Firstline 30651 Fisher 30670 Funai 31268, 30675 Gateway 31158, 31077, 31073 GE 30815, 30717, 30522

31571

30490

31003, 30695

31107, 31086, 31077, 30852, 30778

31087

31117, 31024, 31023, 30874, 30816

31169, 30869, 30833, 30784, 30770, 30705

In the U.S. call 1(877) 675-2224 for assistance.

70 Appendices

Appendix A: Programming the Remote Control, continued

Programming Codes, continued

DVD and Blu-ray Players

GFM 31268, 30675 Go Video 31730, 31304, 31158,

31144, 31099, 31075, 31044, 30869, 30833, 30783, 30744, 30741,

30717, 30715, 30573 GoldStar 30869, 30741 Goodmans 30790 GPX 30769, 30699 Gradiente 30651, 30490 Greenhill 3 0717 Grundig 30705, 30539 Harman/ Kardon Hello Kitty 30831 Hitachi 30664, 30573 Hiteker 30672 Humax 31588, 31500 iLo 31348 Initial 30717 Insignia 32095, 31268, 30675 Integra 31769, 30627, 30571 IRT 30783 JBL 30702 JMB 30695 JSI 31423 JVC 31550, 31275, 31164,

jWin 31049 Kawasaki 30790 Kenwood 30534, 30490 KLH 31149, 31020, 30790,

Kloss 30533 Koss 31423, 31061, 30769,

Lasonic 30798, 30627 Lecson 31533 Lenoxx 31127 LG 30869, 30741, 30591 LiteOn 31738, 31656, 31440,

Loewe 30741, 30511 Logix 30783 Magnasonic 30675, 30651 Magnavox 31506, 31354, 31268,

Marantz 30675, 30539, 30503 McIntosh 31533, 31273 Medion 30651 Memorex 31270, 30831, 30695 Microsoft 32083, 30522 Minato 30752 Mintek 30839, 30717 Mitsubishi 31521, 30521 Mustek 30730

30702, 30582

30867, 30623, 30558

30717

30651

31416, 31158, 31058

30675, 30646, 30539,

30503

DVD and Blu-ray Players

Myryad 30894 NAD 3 0741 Naiko 30770 NEC 30869, 30785 Nesa 30717 Nex xTe ch 31402 Norcent 31265, 31107, 31003,

30872 Onkyo 31769, 30627, 30503 Oppo 31224, 30575 Optimus 30571 Oritron 30651 Palsonic 30852, 30672 Panasonic 31762, 31641, 30703,

30632, 30571, 30503,

30490 Philco 30675 Philips 32084, 32056, 31506,

31354, 31340, 31267,

31158, 30675, 30646,

30539, 30503 Phonotrend 30699 PianoDisc 31024 Pioneer 31571, 31512, 31460,

30632, 30631, 30571,

30525, 30142 Polaroid 31086, 31061, 31020 Polk Audio 30539 Portland 30770 Presidian 31738, 30675 Proceed 30672 Proscan 30522 Prosonic 30699 ProVision 30778 Qwestar 30651 Radionette 30741 RadioShack 30571 RCA 31769, 30822, 30790,

30717, 30571, 30522 Realistic 30571 Reoc 30752 Revoy 30699 Rio 30869 Rotel 31178, 30623 Rowa 31004 Saba 30651 Sampo 30752, 30698 Samsung 31075, 31044, 30820,

30744, 30573, 30490,

30199 Sansui 30695 Sanyo 30873, 30695, 30675,

30670 Schneider 30783 Schwaiger 30752 Sensory Science

3115 8

DVD and Blu-ray Players

Sharp 32250, 31256, 30752,

30675, 30630 Sharper Image Sherwood 31077, 31043, 30770,

Sherwood Newcastle Shinsonic 30839, 30533 Slim Art 30784 SM Electronic Sonic Blue 31099, 30869, 30783,

Sony 31536, 31533, 31516,

Sungale 31074 SVA 30860, 30717 Sylvania 31268, 30675 Symphonic 31268, 30675 TAG McLaren Tatung 30770 Teac 30790, 30717, 30571 Techni c s 30703, 30490 Techni k a 30770 Technosonic 30730 Tevion 30651 Theta Digital 30571 Thomson 30522, 30511 Tivo 31588, 31512, 31503 Toshiba 31769, 31608, 31588,

Tredex 30800 Unimax 30770 United 30730 Universum 30591 Urban Concepts US Logic 30839 V 31226, 31064 Venturer 30790 Vizio 31226, 31064 Wesder 30699 Xbox 32083, 30522 Yamaha 30646, 30545, 30539,

Yamakawa 30872 Zenith 30869, 30741, 30591,

Zeus 30784 Zoece 31265

31117

30633

31077

30730

30715, 30573

31431, 31070, 31033,

30864, 30533

30894

31515, 31510, 31503,

31154, 30695, 30573,

30539, 30503

30497, 30490

30503

In Canada call 1(800) 450-6487 for assistance.

Appendices 71

Appendix B: Bypassing the Parental Lock

Mitsubishi LASERVUE TV

L75-A81 L75-A91

Bypassing the Parental Lock

After you set the lock, you must use your pass code to:

View a locked program• View the locked TV• Cancel the lock• Enter the • Lock menus

If you forget your pass code, you can view the locked TV without entering your pass code. When prompted for the pass code, press the number 9 and keys on the TV remote control at the same time. This process temporarily unlocks the TV.

When entering the Lock menu, you are prompted to enter a pass code.

• Tochangethepasscode,press9 and

at the same time. Either enter a new pass code to open the Lock menu and make changes or press

BACK

to close the menu.

(

LAST

(

LAST

)

Lock Bypass Instructions Have Been Filed for

Future Reference

IMPORTAN T

Cut along the dotted line and file bypass instructions in a safe place for future reference.

• Ifanyofthelocksareturnedonandyouexitthe

menus when prompted for a new code, the old code and all lock settings are retained.

• Ifalllocksareturnedoffandyouexitthemenus

when prompted for a new code, then the previous code is erased.

IMPORTAN T

When changing or deleting your pass code, you must use the remote control included with this TV. You cannot use a Mitsubishi remote control from another component or a “universal” remote.

In the U.S. call 1(877) 675-2224 for assistance.

72 Appendices

This page intentionally left blank

In Canada call 1(800) 450-6487 for assistance.

Appendices 73

Appendix C: HDMI Control of CEC Devices

Many new HDMI devices have a feature called Consumer Electronics Control (CEC) or HDMI Control. HDMI Control allows one device, such as the TV, to control other devices, such as an A/V receiver or disc player. Use of CEC is optional.

Each manufacturer chooses which CEC functions to support so it is difficult to predict which devices and features are compatible with Mitsubishi’s HDMI Control. You may find that CEC functions for a specific device are limited.

To use HDMI Control, you must enable it in both the TV and the device.

In the TV.• Enable HDMI control from the New

Device Found screen or from the Inputs > HDMI Control menu.

I•

n the Device. Most devices with HDMI CEC com-

patibility let you turn it on or off in the device menus, where it is typically listed as “HDMI Control.”

Enabling HDMI Control of CEC Devices

To ensure proper detection

Power on HDMI devices before connecting them to • the TV. Connect and set up HDMI devices one at a time.•

Power on the device and allow it to complete the

power-on sequence (boot up). Stop any playback. Connect the device to one of the TV’s HDMI inputs.

When the TV detects the connection, the

Device Found screen will appear.

Note: See “If the New Device Found Screen Has No

HDMI Control Option” on this page if there is no HDMI Control option.

New Device Found screen with HDMI Control option. This screen displays only if the device’s HDMI Control is enabled

New

If prompted for a name,

highlight the name you want to assign the device.

Highlight

Device Found screen.

Note: At any time after completing Auto Input Sens-

To supplement HDMI control with NetCommand IR

control, see page 50.

On.

EXIT and press

ing, you can set the TV’s HDMI control on or off in the Inputs > HDMI Control menu.

ENTER

to close the New

If the New Device Found Screen Has No HDMI Control Option

If the New Device Found screen shows no option for HDMI Control, one of these conditions applies:

HDMI Control is turned off in the menus of the • new device

Action:

Highlight a. EXIT and press New Device Found screen.

Display the device’s setup menus and enable b. the device’s CEC capabilities. Wait for the TV’s c. New Device Found screen to appear again. If the d. New Device Found screen does not appear, power off the device. Power on the device and wait for the New Device Found screen to display with the HDMI Control option.

The device does not have CEC compatibility•

Action:

Control the device with its own remote control or program the TV’s remote control to operate the device.

Use the TV’s NetCommand IR control ( - page

50).

ENTER

to close the

In the U.S. call 1(877) 675-2224 for assistance.

74 Appendices

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

HDMI

OUT

CEC-enabled devices connected with HDMI cables

DIGITAL

AUDIO IN

A/V receiver

with HDMI

output

Cable box

DVD player

DIGITAL

AUDIO

OUTPUT

DIGITAL

AUDIO

OUTPUT

Optional digital

audio connection

HDMI

cable

HDMI Control of an HDMI A/V Receiver and Connected Devices

Use this setup to control CEC-enabled devices connected to your CEC-enabled A/V receiver.

Note: Connect the A/V receiver to the TV with an

HDMI cable before making other connections.

Enable HDMI Control for the A/V receiver as

described in “Enabling HDMI Control of CEC Devices” on the previous page.

Power on the HDMI device you wish to connect to

the A/V receiver (such as a disc player, cable box, or satellite receiver). Allow the device to complete the power-on sequence (boot up). Stop playback if the device starts playing.

Connect the device to the A/V receiver with an

HDMI cable. Select the device’s HDMI input on the A/V receiv-

er’s front panel controls or remote control. When the TV detects the connection, the

Device Found screen will appear.

New

Note: If the TV is unable to detect the device, either

the device’s CEC capability is not enabled or the device is not CEC compatible. Enable HDMI control through the device’s menus before continuing. You may need to temporarily connect the device directly to the TV to view device menus.

In the TV’s

New

Device Found

screen, highlight On.

Highlight

EXIT and press

Device Found screen. Optional: Connect the TV’s

8. DIGITAL AUDIO

OUTPUT

additional connection if:

to an input on the A/V receiver. Use this

You want the ability to switch between the A/V • receiver speakers and the TV speakers. You want to use the A/V receiver to listen to • devices connected to the TV only, e.g., an antenna input or camcorder.

ENTER

to close the New

Connecting HDMI devices. The optional digital audio connection allows you to hear audio through the A/V receiver from devices connected to the TV only.

If desired, perform NetCommand IR Learning to

supplement CEC functions. You must first connect and place IR emitters for the devices. See page 50.

In Canada call 1(800) 450-6487 for assistance.

Appendices 75

Resolving CEC Conflicts

Because each manufacturer selects which CEC functions to support, some devices can conflict with other devices. If control conflicts arise, you can:

Turn off TV control of an individual CEC-enabled • device (see below).

Turn off CEC in the setup menu of one of the • devices.

Turning Off the TV’s HDMI Control of a CEC Device

Press

on the TV remote control.

Highlight to open the menu.

Move to the device name and press Off to turn off the TV’s ability to control the device.

Press

Inputs > HDMI Control and press

to clear the menu.

ENTER

to select

Using HDMI Control

As an example of using HDMI Control, press the device itself to:

Power on the TV• Switch to the device (no need to display the • Activity menu) Begin play of the device•

Direct Keys

Test your equipment with the TV’s remote control to find additional supported commands. See the table below for commands that may be available, depending on the individual device.

CEC-enabled VCR, DVD, and DVR functions that may be available:

Record/

Playback

Navigation

ENTER

CANCEL

(to cancel)

Channel Tuning Other

CHANNEL UP/DN GUIDE

Digits

0–9, CANCEL MENU

ENTER

PL AY

Inputs > HDMI Control menu

Removing an HDMI Device

Power off the device.

Disconnect the HDMI cable.

Press

on the TV remote control to enter the

TV main menu. Highlight

the menu. Select Press

Inputs > Name and press

Delete from the HDMI input names.

to clear the menus.

ENTER

to open

If you have a CEC-enabled A/V receiver, CEC-enabled devices connected to the A/V receiver with an HDMI cable may also be controllable. They can be selected from the TV’s Activity menu.

CEC-enabled A/V receiver functions that may be available:

Try the • keys. To open the A/V receiver menu, follow these steps:•

The MORE Menu

Press of additional supported functions for the current CEC-enabled device. To issue a command, press the number key indicated in the menu.

VOLUME UP/DOWN, MUTE

While watching TV, press 1. Press 2. until the Speakers option displays. Press 3. to select AVR as the source. Press 4.

and then

menu.

on the TV’s remote control to see a menu

, and menu-navigation

then 9 (AUDIO).

1 (MENU)

to display the

Inputs > Name menu with Delete selected for HDMI-3.

MORE key: Sample menu for

a CEC-enabled DVD player

In the U.S. call 1(877) 675-2224 for assistance.

76 Appendices

Appendix D: TV Care

Cleaning Recommendations

Normally, light dusting with a dry, non-scratching duster

will keep your TV clean. If cleaning beyond this is

needed, please use the following guidelines: First, turn off the TV and unplug the power cord from

the power outlet.

Occasionally clean dust build-up from the air-intake grilles on the back and sides of the TV. Clean using a vacuum cleaner with a brush attachment.

Top and Sides of the TV

Gently wipe down your TV with a soft, non-abrasive • cloth such as cotton flannel or microfiber, or a clean cloth diaper, lightly moistened with water. Dry with a second dry, soft, non-abrasive cloth. For oily dirt, add a few drops of mild liquid deter-• gent, such as dishwashing detergent, to the water used to moisten the cloth. Rinse with a second cloth moistened only with water. Dry with a third dry, soft, non-abrasive cloth.

Screen

Follow the instructions for the top and sides, wiping • gently in an up and down motion. Clean the entire screen evenly, not just sections of • the screen. Do not allow liquid to drip down the screen, as • some liquid may enter the TV through the gap between the screen and screen frame.

You may purchase Mitsubishi Screen Cleaner, part •

number CLEANER-VSS, by calling (800) 553-7278.

Care of the Remote Control

Remote Control Tips

For longer life, use alkaline batteries.• Do not mix old and new batteries.• Be within 20 feet of the equipment.• Do not press two or more keys at the same time •

unless instructed to do so. Do not allow the unit to get wet or become heated.• Keep the unit out of direct sunlight.• Avoid dropping on hard surfaces.• Do not use harsh chemicals to clean. Use only a •

soft, lightly moistened cloth.

Resetting the Remote Control

If TV mode is selected and the TV does not respond properly, reset the remote control.

Press and hold

mode indicator blinks twice and goes off. Release the

Press keys

blink twice when you finish entering the code. When entering the code, pause for a moment between each key press to ensure it is recognized.

Low-Battery Indicator

If you press a key and the mode indicator blinks five times, replace the remote control’s batteries.

POWER

for several seconds until the

POWER

key.

0 0 9 3 5

and the mode indicator will

General Cleaning Precautions

DO NOT allow liquid to enter the TV through the • ventilation slots or any crevice. DO NOT use any strong or abrasive cleaners, as • these can scratch the surfaces. DO NOT use any cleaners containing ammonia, • bleach, alcohol, benzene, or thinners, as these can dull the surfaces. DO NOT spray liquids or cleaners directly on the •

TV’s surfaces.

DO NOT scrub or rub the TV harshly. Wipe it gently.•

In Canada call 1(800) 450-6487 for assistance.

Appendices 77

Appendix E: Troubleshooting

To contact Mitsubishi with questions about your TV, see page 4.

TV Reset Comparison Guide

You can resolve many common TV problems using the reset functions described in the following table. See also the troubleshooting suggestions later in this appendix.

IMPORTANT Before you change sound or picture settings: If

picture or sound settings seem wrong for a broadcast

Reset Name When to Use How to Use Resulting Action

Format When the picture

shape seems incorrect, use

PerfectColor™/ PerfecTint™ Reset

(for the single input currently being watched)

MORE > 0

change the shape of the picture.

When the color intensities seem out of balance, use the PerfectColor/PerfecTint reset to reset the color balances to the original factory settings. Both PerfectColor and PerfecTint are reset at the same time.

(FORMAT) to

Press the edly press 0 (FO RMAT) to cycle through the available aspect ratios.

While viewing the input to 1. be reset, press go to Adjust > Picture+ > PerfectColor.

Press 2. PerfectColor adjustment screen.

Press 3.

channel (a channel from the satellite receiver), first check other channels from the same input before changing settings. If most other channels from the same input seem correct, there is likely a problem with the broadcast rather than with the TV. Use care in this case, as changes you make to fix problems on individual channels also affect all other channels on the same input.

key and then repeat-

and

ENTER

to display the

CANCEL

to reset the colors.

ANT

input, a cable box, or

The last-used format for a signal type is memorized for each input. The next time the same input and the same signal type is viewed, the last-used format will be recalled.

All PerfectColor/PerfecTint sliders are reset to the original center position. The PefectColor/ PerfecTint settings for other inputs remain unchanged.

A/V Memory Reset

(for the single input currently being watched)

A/V Reset

(for all inputs)

Channel Memorization

When audio and/ or video settings for a single input seem incorrect, use A/V Memory Reset to return the input to the original factory settings

To reset audio and video adjustments for all inputs to the original factory settings.

To erase and re-memorize channels on the

ANT

input.

While viewing the input to reset, 1. press

and go to Adjust >

Reset. Press 2.

ENTER

to highlight the

Reset icon. Press 3.

ENTER

again to reset.

While viewing the TV, press the control-panel buttons

VOLUME DOWN

least two seconds.

While viewing the TV, press 1.

Navigate to the 2. Initial> Channel menu. Press 3. Highlight the reception mode, 4. e.g. Ant Air. Highlight 5. Scan. Press 6. memorization.

at the same time for at

to display the main menu.

ENTER.

ENTER

ACTIVITY

to start channel

and

All Audio and Video settings for the current input are returned to the original factory settings.

All Audio and Video settings are returned to the original factory settings, including Listen To, Language, audio Balance, Closed Captions, and Format.

All previously memorized channels for the antenna input are erased and a new set of memorized channels is created. To add or delete individual channels, see Initial > Channel > Edit menu instructions on page 44.

In the U.S. call 1(877) 675-2224 for assistance.

78 Appendices

Appendix E: Troubleshooting, continued

Reset Name When to Use How to Use Resulting Action

Lock Menu Pass Code

Control-Panel Lock Release

Auto Input Sensing for HDMI

System Reset If the TV does not turn

TV Reset

IMPORTA N T:

Use this reset only if other troubleshooting has been unsuccessful.

To change your Lock menu pass code

To re-enable the control-panel buttons after activation of the Control-Panel Lock

If the New Device Found screen does not appear when you connect an HDMI device.

on or off, does not respond to the remote control or controlpanel buttons, or has audio but no video.

To reset all consumeraccessible settings and all memories to the original factory defaults.

Use TV Reset if the TV can respond to controls but TV behavior is abnormal.

CAUTION: All ownerperformed setups and adjustments will be erased.

See the page 71.

Press and hold the ACTIVITY the control panel for ten seconds. If the TV is powered off, you can now press the

Press and hold the the control panel for ten seconds.

cutout page from Appendix B,

button on

POWER

button to turn it on.

Disconnect the HDMI device.1. Delete the HDMI input in the 2. Inputs > Name menu (see page

45). Power on and connect the new 3. device.

POWER

button on

While viewing the TV, press 1.

to display the TV main menu. With the main menu displayed, 2. press number keys 1 2 3 to display the Reset menu.

READ THE ON-SCREEN 3. WARNING AND INSTRUCTIONS.

If you do not wish to use this • reset, press back out.

If you do wish to use the • reset, press all memories and settings.

BACK

ENTER

to erase

Allows establishment of a new code.

Allows the control panel to be unlocked if the remote control is misplaced.

The New Device Found screen will display.

The TV will turn off. Power on the TV and the green LED will flash quickly for about one minute. The changes you made most recently, before using SYSTEM RESET be lost.

The TV will start the initialization process and then turn off. Power on the TV and the front green LED will start flashing. All memory and settings outlined in this Owner’s Guide will need to be set again.

, may

VUDU

™

Reset VUDU Connection

(L75-A91)

VUDU Reset VUDU Account Password

(L75-A91)

VUDU Reset Parental Controls Pass code

(L75-A91)

VUDU does not • respond to commands. The selection does not • play (e.g., screen is black or the “Loading” message is frozen on screen).

You have forgotten your account password.

You have forgotten your pass code.

Press the 1. Press the 2.

Using a computer, go to www.VUDU.com.

Call VUDU Customer Care at 1-888-554-VUDU (8838).

In Canada call 1(800) 450-6487 for assistance.

MORE 2

key.

Key.

The screen will briefly go blank while VUDU initializes. This reset does not reset the TV or any TV settings.

Reset your account password from the VUDU website (requires access to e-mail).

VUDU Customer Care will reset your pass code.

Appendices 79

Appendix E: Troubleshooting, continued

General TV Operation

Symptom Remarks

1. A fan is running even while the TV is powered off.

The TV remote control does not work. Check that the batteries are fresh and installed correctly.•

When I try to use the remote control, the POWER key blinks five times.

TV does not respond to the remote control or to control-panel buttons and TV will not power on or off.

When a device is selected from the Activity menu, the screen is blue or black (no signal source).

You have forgotten your Lock menu pass code. See “Bypassing the Parental Lock”, Appendix B.

Rating restrictions are not working.

On-screen displays appear each time you change a function.

9. A warning message appeared on screen stating, “TV will shut down in a few seconds. Please check if the air flow is blocked.”

10.

I have turned on CEC for my HDMI devices but control is erratic and I wish to disable it.

The room is too warm. When the TV is off, internal components continue to draw power and must be cooled by the fan.

Check that the control mode on the remote is set to TV.• Be no more than 20 feet from the TV when using the remote control.• Program the remote control to operate the TV or other device.• Reset the remote control.•

Replace the batteries.

Unplug the AC power cord for 10 seconds.• Press and hold the POWER button on the control panel to • perform system reset.

• Makesuretheselecteddeviceisturnedon.

• Beginplayofthedevice.

Open the Lock > Parental Lock menu and:

• Verifythattheratingslocksareactive.

• ChecktheLockTime/UnlockTimetocheckifratingrestric-

tions are disabled.

• RatingrestrictionsapplyonlytocontentontheANTinput.

Normal TV operation.

• InternalTVtemperaturehasexceededproperlevels.Cool

the room.

• TheTVhasoverheated.Clearblockedairventsandensure

at least four inches of clearance on all sides of the TV. First •

turn off the TV’s HDMI control for the specific device. Open the Inputs > HDMI Control menu, select the device, select Off. Disable CEC on the device itself. See the device’s instruc-• tions. If the problem persists, do the following:•

Disconnect the device from the TV.1. Open the Inputs > Name menu and select Delete for the 2. device. Reconnect the device to the TV and Auto Input Sensing 3. will recognize the device with CEC disabled.

In the U.S. call 1(877) 675-2224 for assistance.

80 Appendices

Appendix E: Troubleshooting, continued

TV Channels (from the ANT input)

Symptom Remarks

The TV takes several seconds to respond to channel changes.

You cannot access a channel.

3. When ChannelView list is displayed, informa- tion appears incomplete

It is normal for digital channels to take longer to tune in.• Press ENTER after entering a channel number to avoid • delays. Use a 4-digit number for an over-the-air digital channel.• Use a 6-digit number for digital cable channels if your cable • service is able to recognize 6-digit channel numbers.

Use number keys instead of CHANNEL Up/Down.• Be sure the channel you want to view is in memory.• Check that the TV is switched to the correct device or • antenna for that channel by pressing the ACTIVITY key. Make sure the Lock > Parent menu lock is set to Off.• If you cannot tune to a virtual digital channel even though the • TV has already memorized digital channels, tune to the physical channel number used by the broadcaster. The virtual channel will then be automatically added to memory. You may be trying to tune to an analog channel that is no • longer broadcasting.

Press INFO to update the display for the highlighted channel.• Program information is displayed only for the currently tuned • channel. Available information is sent from the broadcaster or cable • provider. No other data is available. Make sure the TV clock is set correctly.•

TV Power On/Off

Symptom Remarks

1. TV takes an excessively long time to power on.

2. You cannot program the TV to turn on auto- matically (Timer function)

3. TV turned itself off and the light on the front panel started to blink.

4. TV will not power off. Press the POWER button on the control panel for ten seconds

When powered on, the TV needs time to boot up, just as a computer does.

The TV may be locked.• The clock may not be set.•

Momentary power fluctuation caused the TV to turn off to • prevent damage. Wait for the light to stop flashing and turn the TV on again. If the TV does not stay on, press the POWER button on the • control panel for at least eight seconds to perform System Reset. If this happens frequently, obtain an AC line power conditioner/surge protector. An unusual digital signal may have been received, triggering a • protection circuit. Wait for the light to stop flashing and turn TV on.

to perform System Reset.

In Canada call 1(800) 450-6487 for assistance.

Appendices 81

Appendix E: Troubleshooting, continued

Picture

Symptom Remarks

1. Picture does not look like a high-definition picture.

2. TV has sound but no picture. Check that all video inputs are plugged in firmly.•

3. There is a large black or gray rectangle on the screen.

4. You cannot view a picture when playing a VHS tape.

5. VCR or DVD player’s on-screen menus jitter up and down.

6. When viewing a stopped VCR, white lines are rolling on the screen.

7. A color program appears as a black and white image, or the colors are dim, or the screen is black.

8. Picture from an HDMI input is noisy (poor quality).

9. The image from a computer appears dis- torted when viewed on the TV.

Not all signals are high-definition signals. To receive high-definition programming from your cable or satellite provider, you must subscribe to the provider’s high-definition service. Some overthe-air broadcasts are in high-deﬁnition and can be received with a high-quality antenna suited to your location.

Press and hold the POWER button on the control panel for • ten seconds to perform System Reset.

The TV’s analog closed captioning has been set to “text” mode in the Captions menu. Turn off because there is no text information being broadcast.

Check your VCR’s owner’s guide for further troubleshooting.

Stop playback. Possible cause: Many VCRs and DVD players provide on-screen menus at only half-resolution that may appear to jitter up and down.

• TurnoffvideomutefortheVCR.

• Beginplayingthetape.

• ChangetheVCRinputfromLine1totheVCRantennainput.

The PerfectColor color balance has been incorrectly set. Reset the PerfectColor balance.

Upgrade a Category 1 (unmarked) HDMI cable to a Category 2 high-speed HDMI cable.

Normal TV operation. The TV does not correct distortion in • the picture from a computer because the correction process may cut off the edges of the image. The aspect ratio may be wrong for the image. Press MORE • and then 0 (FORMAT) to change.

Sound

Symptom Remarks

1. There is no sound even when the volume is turned up.

• CheckiftheMUTEkeyison.

• AnalogprogramfromtheANTinput:TheTV’s“Listento:”setting

may be set to SAP but no SAP is being broadcast.

• DigitalprogramfromtheANTinput:TheTV’s“Language”setting

may be set to a language not available for the current program.

• CheckthattheSpeakersoptionissettoTVtohearsoundfrom

the TV speakers. Possibly sound is being sent to one of the audio outputs for an A/V receiver or headphones.

• IfusinganA/Vreceiver,checkthattheSpeakersoptionissettoAV

Receiver to hear sound from the A/V receiver speakers.

•

Press and hold the POWER button on the control panel for 10 seconds to perform System Reset.

In the U.S. call 1(877) 675-2224 for assistance.

82 Appendices

Appendix E: Troubleshooting, continued

Sound

Symptom Remarks

2. The sound does not match the screen picture.

3. The sound from my A/V receiver does not match the screen picture (I should hear the correct audio from my A/V receiver).

4. Cannot select an audio-only device; it does not appear in the Activity menu.

.5. Sound is coming from the TV speakers

instead of the A/V receiver.

The TV’s “Listen to:” setting may be set to SAP the ANT input)

Check that DIGITAL AUDIO OUTPUT and/or AVR AUDIO • OUTPUT on TV’s main panel is connected to the A/V receiver. Without this connection, devices connected only to the TV (and not the A/V receiver) can be heard only from the TV speakers. Note that this includes the ANT input, a device (such as a camcorder) connected to the convenience panel, and any other device sending audio to the TV only. If using a NetCommand-controlled A/V receiver, NetCommand • may be selecting the wrong A/V receiver audio input. Check the A/V receiver’s NetCommand setup in the Inputs > AVR menu.

Plug an unused video plug into the Input Sensing and make the audio device selectable in the Activity menu.

Disconnect headphones. Connect the TV’s AUDIO OUT to the A/V receiver and select AV Receiver from the New Device Found screen.

(analog program from

Y/V I D E O

jack to activate Auto

NetCommand IR Control (L75-A91)

Symptom Remarks

1. Cannot see the menu from the A/V Receiver. A /V Receiver Set Up for Audio-Only Switching• The A/V Receiver is not connected to any video input of the TV. To check the A/V Receiver menu, temporarily plug into an unused input of the TV, such as Input 3. Exit the New Device Found screen and select Input 3 from the Activity menu. Press MENU on the A/V receiver’s remote control.

A/V Receiver Set Up for Audio and Video Switching over • HDMI

Use the MENU key on the A/V receiver’s remote control.

A/V Receiver with • HDMI Control

Switch the remote control to AUDIO mode. Press the MORE key and then 1 (Menu).

2. NetCommand unable to learn specific device keys.

A/V Device does not use IR format for remote control • signal. ITT and RF formats cannot be learned. Room lighting may affect the signal. Have the remotes very • close (6 inches or less) to the TV during Learning. If learning a Mitsubishi remote control, make sure mode is • not set to TV. Some, but not all, device key functions can be learned by • NetCommand. For example, POWER and PLAY may be learned, but other functions may not. The signal from the remote control may not be strong • enough. Insert fresh batteries and try Learning again.

In Canada call 1(800) 450-6487 for assistance.

Appendices 83

Appendix E: Troubleshooting, continued

NetCommand IR Control (L75-A91)

Symptom Remarks

3. The A/V receiver is the selected audio source but there is no sound.

4. There is no sound from the A/V receiver for my DVD player or other surround sound device even though I learned the IR code for the A/V receiver’s DVD input or other input. (A/V Receiver Set Up for Audio-Only Switching)

5. There is no sound or picture from the A/V receiver for my DVD player or other device connected to the A/V receiver; the A/V receiver should be sending video to the TV over an HDMI cable. (

A/V Receiver Set Up for Audio and Video

Switching over HDMI)

6. I’ve selected my DVD player or other sur- round sound device in combination with the TV speakers but hear no sound from the TV speakers.

7. I “learned” the RECORD key for my VCR/DVR but when I pressed the RECORD key, the VCR/DVR did not record anything.

A/V Receiver Set Up for Audio-Only Switching•

Check to see if the A/V Receiver power is turned on. With A/V receiver power turned on, redisplay the Activ- ity menu and press ENTER to allow NetCommand to correctly select the A/V Receiver input. Incorrect setup in the Inputs > AVR menu. Check the device connection assigned in the AVR menu.

A/V Receiver Set Up for Audio and Video Switching over • HDMI

Check to see if the A/V Receiver power is turned on. If the device is connected only to the TV (e.g., on ANT or a front panel input), verify that the TV’s AUDIO OUTPUT is connected to the A/V receiver. The A/V receiver is not switching properly because you have not learned the IR codes for the A/V receiver inputs to which your devices are connected.

NetCommand A/V receiver setup for the DVD player or digital surround sound device or other device is not switching properly. See “Case 2: Automatic A/V Receiver Switching to a Surround Sound Device,” page 59, and perform A/V receiver setup for a digital surround sound device.

The NetCommand A/V receiver setup is not switching audio and video inputs properly because you did not “learn” the A/V receiver’s IR codes for the device inputs. See “Case 3: Automatic Audio and Video Switching via HDMI,” page 60.

A/V Receiver Set Up for Audio-Only Switching• If you have only an audio connection from the device to the A/V receiver, a physical audio connection from the device to the TV is also required.

Connect the left and right audio output from the device to the appropriate TV audio input. Now you can hear audio from the device through either the TV speakers or the A/V receiver. To switch audio sources, press MORE 9 (Audio), press -

to show the Speakers option, then press to

select AV Receiver or TV.

A/V Receiver Set Up for Audio and Video Switching over HDMI• With your DVD player connected to the A/V receiver, only video is passed from the A/V receiver to the TV because of copy-protection restrictions on the HDMI signal

Check that the VCR or DVR is receiving a signal directly from your cable box or satellite receiver.

In the U.S. call 1(877) 675-2224 for assistance.

84 Trademark and License Information

Trademark and License Information

LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS, INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Digital Light Processing® and DLP® are registered trademarks of Texas Instruments. Manufactured under license from Dolby Laboratories. Dolby is a trademark of Dolby Laboratories. HDMI™ the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI

Licensing LLC.

Imaging Science Foundation Certified Calibration Controls

VUDU™ is a trademark of VUDU, Inc.

x.v.Color and the x.v.Color logo are trademarks of Sony Corporation. ChannelView™, DeepField™ Imager, Easy Connect™, EdgeEnhance™, LASERVUE®, NetCommand®, PerfectColor™,

PerfecTint™, Plush 1080p® 5G, Smooth120 Film Motion™ are trademarks of Mitsubishi Digital Electronics America, Inc.

In Canada call 1(800) 450-6487 for assistance.

Trademark and License Information 85

Mitsubishi TV Software

END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE

IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and

Mitsubishi Digital Electronics America, Inc. (MDEA) for all software pre installed and/or provided along with this television (“Software”). By utilizing this television and Software, you agree to be bound by the terms of this License Agreement.

The Software is protected by United States copyright laws and international treaty provisions, as well as other intellectual property laws

and treaties. The Software is licensed, not sold.

1. LICENSE GRANT. MDEA grants you a non-exclusive, non-transferable, limited right and license to use one copy of the Software only with the Mitsubishi television model that included this owner’s guide and owned by you.

2. RIGHTS AND LIMITATIONS. Software Not for Resale. You may not resell or otherwise transfer for value the Software, except in conjunction with a sale of the TV that

Software has been pre installed. Prohibition on Reverse Engineering, Decompilation and Disassembly. The Software contains trade secrets or other proprietary material

in its human perceivable form and to protect them, you may not reverse engineer, decompile, or disassemble, or otherwise reduce the Software to any human perceivable form, except to the extent that the foregoing restriction is expressly prohibited by applicable law.

Separation of Components. The Software is licensed as a single product. Its component parts may not be separated for use on more than one TV.

No Rental. You may not rent, lease, lend, or sublicense the Software.

Trademarks. This License Agreement does not grant you any rights to any trademarks of MDEA.

3. VIOLATIONS. You understand that any use, copying or transfer of the Software, except as permitted pursuant to this License, may subject you to serious criminal and civil penalties including damages and an award to MDEA of attorneys’ fees in connection with any violation of this License. You further understand that you may be held legally responsible for any copyright infringement or other violation of intellectual property rights that is caused, encouraged, or induced by your failure to abide by the terms of the License. This license is effective until terminated, and will terminate immediately without notice from MDEA or judicial resolution if you fail to comply with any provision of this License.

4. COPYRIGHT. All title and intellectual property rights in and to the Software (including but not limited to any images, photographs, animations, video, audio, music, text, and “applets” incorporated into the Software), and any accompanying printed materials are owned by or licensed to MDEA. All title and intellectual property rights in and to the content which may be accessed through use of the Software is the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and treaties. This License Agreement grants you no rights to use such content, except that you own the media on which the Software is recorded, but MDEA and its licensors retain ownership of the Software itself. All rights not expressly granted are reserved by MDEA.

5. EXPORT RESTRICTIONS. MDEA is licensing the Software for use within the United States and Canada. You agree that you will not export or re-export the Software. You specifically agree not to export or re-export the Software: (i) to any country to which the U.S. has embargoed or restricted the export of goods or services, which currently include, but are not necessarily limited to Cuba, Iran, Iraq, Libya, North Korea, Sudan, and Syria, or to any national of any such country, wherever located, who intends to transmit or transport the Software back to such country; (ii) to any person or entity who you know or have reason to know will utilize the Software in the design, development, or production of nuclear, chemical, or biological weapons; or (iii) to any person or entity who has been prohibited from participating in U.S. export transactions by any federal agency of the U.S. government. You warrant and represent that neither the BXA nor any other U.S. federal agency has suspended, revoked, or denied your export privileges.

6. DISCLAIMER OF WARRANTY. EXCEPT AS OTHERWISE PROVIDED IN THIS LICENSE OR IN THE LIMITED WARRANTY

APPLICABLE TO THE TV, MDEA MAKES NO OTHER WARRANTIES OF ANY KIND WHATSOEVER REGARDING THE SOFTWARE AND HEREBY EXPRESSLY DISCLAIMS ALL WARRANTIES OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, WITH RESPECT TO THE SOFTWARE. ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY DISCLAIMED BY MDEA. IN NO EVENT SHALL MDEA BE LIABLE TO YOU OR ANY THIRD PARTIES, IN CONTRACT, IN TORT OR OTHERWISE, FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE. BECAUSE SOME

JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES, THE ABOVE LIMITATION MAY

NOT APPLY TO YOU.

7. LIMITATION OF LIABILITY. MDEA SHALL NOT, UNDER ANY CIRCUMSTANCES BE LIABLE TO YOU OR ANY THIRD PARTIES FOR ANY DAMAGES OF ANY NATURE, WHETHER INDIRECT, SPECIAL , INCIDENTAL, CONSEQUENTIAL OR OTHERWISE, INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOST PROFITS, LOSS OF GOOD WILL OR EXPENDITURES MADE OR COMMITTED FOR IN RELIANCE ON THE CONTINUATION OF THIS LICENSE. YOU AGREE THAT NEITHER MDEA’S BREACH OF THIS LICENSE NOR ITS FAILURE TO REPAIR A DEFECT, ERROR OR BUG SHALL CONSTITUTE A FAILURE OF THE ESSENTIAL PURPOSE OF THIS LICENSE. BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. MDEA’s

liability to you for direct damages for any cause whatsoever and regardless of the form of the action, will be limited to the money

paid by you for the TV (based on fair market value of the TV) that caused the damages.

8. GENERAL. This License Agreement will be governed by the laws of the State of California.

WARNING: This product contains chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm.

In the U.S. call 1(877) 675-2224 for assistance.

86 Trademark and License Information

GNU General Public License

Version 2, June 1991

Copyright (C) 1989, 1991 Free Software Foundation, Inc. 675 Mass Ave, Cambridge, MA 02139, USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.

To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.

We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.

Also, for each author’s protection and ours, we want to make cer tain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors’ reputations.

Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all.

The precise terms and conditions for copying, distribution and modiﬁcation follow.

GNU GENERAL PUBLIC LICENSE

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a por tion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”.

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.

1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:

a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.

b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.

c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.)

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program.

In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

Preamble

In Canada call 1(800) 450-6487 for assistance.

Trademark and License Information 87

3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following:

a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,

b) Accompany it with a written offer, valid for at least three years, to give any third par ty, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,

c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)

The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binar y form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.

4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such par ties remain in full compliance.

5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.

6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.

7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/ donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.

10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARR ANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANT Y OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICUL AR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

In the U.S. call 1(877) 675-2224 for assistance.

88 Warranty

Mitsubishi LASERVUE® Television Limited Warranty (U.S.A. only)

MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. (“MDEA”) warrants as follows to the original purchaser of this television from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason of against defects arising from improper workmanship and/or material:

a. Parts. All parts (except any software incorporated into this television and Lenticular screen surface) are warranted for a period of one (1) year from the date of the original purchase at retail. We will repair or replace, at our option, any defective part without charge for the part. Lenticular (i.e. front picture) screen surface is warranted against defect in materials and workmanship for a period of thirty (30) days from the date of the original purchase at retail. Parts used for replacement may be replaced with those of like kind and quality and may be new or remanufactured. Parts used for replacement are warranted for the remainder of the original warranty period.

b. Embedded Software. MDEA warrants that all software incorporated into this television set (the “Embedded Software”) will perform in accordance with the functional description of Embedded Software in all material respects, but MDEA does not warrant that the Embedded Software is error-free. MDEA also does not warrant that the Embedded Software will be compatible under HDMI CEC software standards with products produced by any other manufacturer. The limited warranty contained in this section shall continue for a period of one (1) year from the date of the original purchase at retail. If, after prompt notice within the warranty period, MDEA determines that the Embedded Software has failed to perform in accordance with such functional description in all material respects and if such failure is not due to accident, misuse, modification or misapplication of the Embedded Software, then MDEA shall modify or replace the nonconforming Embedded Software at no charge to you, which at MDEA’s sole discretion may be fulfilled by means of modification or replacement software contained on a replacement memory card for Customer installation. The foregoing shall be MDEA’s sole obligation to you under this limited warranty. All rights under this limited warranty on the Embedded Software also subject to your acceptance of and compliance with the terms of the Software License Agreement applicable to this television, and this limited warranty on the Embedded Software shall be null and void if the Embedded Software is modified or changed in any manner except as specifically authorized by MDEA.

c. Labor. For thirty (30) days after the original purchase at retail, we will repair or replace, at our option the Lenticular Screen if the surface proves defective. For certain items that are designed to be replaced by the consumer, including (but not limited to) some Embedded Software, the consumer is solely responsible for any replacement labor. For all other parts, we will provide the labor for a warranty repair by an authorized MITSUBISHI service center without charge for one (1) year from the original date of purchase at retail.

d. Notice. To obtain warranty service, you must notify an authorized MITSUBISHI service center of any defect within the applicable warranty time period.

e. This LASERVUE Television uses a single DLP chip to create the screen image. This technology creates the image using small dots, or picture elements (pixels). Your LASERVUE TV is manufactured to a high level of performance and quality, in fact, 99.99% perfect in the number of properly functioning pixels. As in other display technology, sometimes a pixel is continuously active, inactive or the incorrect color. Our standard is clear; MDEA warrants only that the percentage of properly functioning pixels will be not less than 99.99% of all pixels.

BEFORE REQUESTING SERVICE, please review the instruction booklet to insure proper installation and correct customer control adjustment. If the problem persists please arrange for warranty service.

1. TO OBTAIN WARRANTY SERVICE:

a. Contact your nearest authorized MITSUBISHI service center, whose name and address can be obtained from your MITSUBISHI dealer, by writing at the address provided below, calling MDEA at 800-332-2119, or by using the support feature of our website at www.Mitsubishi-tv.com.

b. Warranty service will be provided in your home or, if required, at an authorized service shop, provided that your television is located within the geographic territory customarily covered by an authorized MITSUBISHI service center. If not, you must either deliver your television to an authorized service location at your own expense, or pay for any travel and/or transportation costs the service center may charge to and from your home. Actual service labor will be provided without charge.

In Canada call 1(800) 450-6487 for assistance.

Warranty 89

c. Proof of purchase date from an authorized MITSUBISHI dealer is required when requesting warranty service. Present your sales receipt or other document which establishes proof and date of purchase. THE RETURN OF THE OWNER REGISTRATION CARD IS NOT A CONDITION OF COVERAGE UNDER THIS LIMITED WARRANTY. However, please return the Owner Registration Card so that we can contact you should a question of safety arise which could affect you.

2. THIS LIMITED WARRANTY DOES NOT COVER:

a. Up to .01% pixel outages (small dot picture elements that are dark or incorrectly illuminated).

b. Damage to the lenticular screen or Fresnel lens, screen frame, cosmetic damage or to any other damage where such damage is caused by unauthorized modification, alteration, repairs to or service of the product by anyone other than an authorized MITSUBISHI service center; physical abuse to or misuse of the product (including any failure to carry out any maintenance as described in the Owner’s Guide including air vent cleaning or any product damaged by excessive physical or electrical stress); any products that have had a serial number or any part thereof altered, defaced or removed; product use in any manner contrary to the Owner’s Guide; freight damage; or any damage caused by acts of God or other factors beyond the reasonable control of MDEA, such as power surge damage caused by electrical system or lightning. This limited warranty also excludes service calls where no defect in the product covered under this warranty is found, service calls related to unsatisfactory audio or visual reception or signal unless caused by a defect in the product that is covered under this limited warranty, all costs, expenses or any other damages arising from product installation, removal from or re-installation into custom installations or on wall mountings, or set-ups, any adjustments of user controls (including contrast, brightness, color, tint, fine tuning, sharpness), other adjustment necessary to prepare the unit for display or use, connection with any external audio receiver, antenna, cable or satellite systems, or service of products purchased or serviced outside the U.S.A. Please consult the operating instructions contained in the Owner’s Guide furnished with the product for information regarding user controls.

3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY WHICH, BUT FOR THIS PROVISION, MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY LIMITED TO A TERM OF ONE YEAR.

4. UNDER NO CIRCUMSTANCES SHALL MDEA BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY, BREACH OF CONTRACT, OR OTHERWISE.

5. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental, special, or consequential damages, so the above limitations or exclusions may not apply to you.

6. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. 9351 Jeronimo Road Irvine, CA 92618-1904

In the U.S. call 1(877) 675-2224 for assistance.

90 Warranty

Mitsubishi LASERVUE® Television Limited Warranty

This limited warranty is valid only for products purchased, used and serviced in Canada. Subject to the terms, conditions and exclusions in this limited warranty, MITSUBISHI ELECTRIC SALES CANADA INC. (“MESCA”) warrants as follows to the original purchaser of this television from an Authorized Dealer of MESCA, should it prove defective under normal residential use by reason of defects arising from improper workmanship and/or material:

a. Parts. All parts, with the exception of the television Screen and any software incorporated into this television, are warranted for a period of one (1) year from the date of the original purchase at retail. We will repair or replace, at our option, any defective part without charge for the part. The television Screen surface is warranted against defects in materials and workmanship for a period of thirty (30) days from the date of the original purchase at retail. Parts used for replacement may be replaced with those of like kind and quality and may be new or remanufactured. Parts used for replacement are warranted for the remainder of the original warranty period.

b. Embedded Software. MESCA warrants that all software incorporated into this television set (the “Embedded Software”) will perform in accordance with the functional description of Embedded Software in all material respects, but MESCA does not warrant that the Embedded Software is error-free. MESCA also does not warrant that the Embedded Software will be compatible under HDMI CEC software standards with products produced by any other manufacturer. The limited warranty contained in this section shall continue for a period of one (1) year from the date of the original purchase at retail. If, after prompt notice within the warranty period, MESCA determines that the Embedded Software has failed to perform in accordance with such functional description in all material respects and if such failure is not due to accident, misuse, modification or misapplication of the Embedded Software, then MESCA shall modify or replace the nonconforming Embedded Software at no charge to you, which at MESCA’s sole discretion may be fulfilled by means of modification or replacement software contained on a replacement memory card for Customer installation. The foregoing shall be MESCA’s sole obligation to you under this limited warranty. All rights under this limited warranty on the Embedded Software also subject to your acceptance of and compliance with the terms of the Software License Agreement applicable to this television, and this limited warranty on the Embedded Software shall be null and void if the Embedded Software is modified or changed in any manner except as specifically authorized by MESCA.

(Canada

only)

c. Labor. For thirty (30) days after the original purchase at retail, we will repair or replace the Screen at our option, if the surface proves defective. For certain items that are designed to be replaced by the consumer, including (but not limited to) some Embedded Software, the consumer is solely responsible for any replacement labor. For all other parts, we will provide the labor for a warranty repair by an authorized MESCA service centre without charge for one (1) year from the original date of purchase at retail.

d. Notice. To obtain warranty service, you must notify MESCA of any defect within the applicable warranty time period.

e. Pixel Defects. This LASERVUE Television uses a single DLP chip to create the screen image. This technology creates the image using small dots, or picture elements (pixels). Your LASERVUE TV is manufactured to a high level of performance and quality; in fact, 99.99% perfect in the number of properly functioning pixels. As in other display technology, sometimes a pixel is continuously active, inactive or the incorrect color. Our standard is clear; MESCA warrants only that the percentage of properly functioning pixels will be not less than 99.99% of all pixels.

BEFORE REQUESTING SERVICE, please review the Owner’s Guide, including the troubleshooting section to insure proper installation and correct customer control adjustment. If the problem persists, please contact us for assistance.

PRODUCT REGISTRATION is not a condition of warranty, however to offer you an enhanced level of service or to contact you in the unlikely event that a safety notification is required, please register your purchase at www.MitsubishiElectric.ca.

1. TO OBTAIN WARRANTY SERVICE:

a. You must contact MESCA to obtain warranty service procedures and the location of the nearest authorized MESCA service centre by writing to the address provided below or calling MESCA at 1-800-450-6487, or using the “contact us” feature of our website at www.MitsubishiElectric.ca

b. Warranty service will be provided in your home or, if required, at an authorized service facility, provided that your television is located within 50 km of an authorized MESCA service centre and accessible by roads. If not, you must

In Canada call 1(800) 450-6487 for assistance.

Warranty 91

either deliver your television to an authorized service centre at your own expense or pay for any transportation costs to and from your home. Actual service labor will be provided without charge.

c. Proof of purchase date from an authorized MESCA dealer is a condition of this warranty. When requesting warranty service, you must provide your sales receipt or other document which establishes proof and date of purchase.

2. THIS LIMITED WARRANTY DOES NOT COVER:

a. Up to 0.01% pixel outages (small dot picture elements that are dark or incorrectly illuminated).

b. Damage to the screen components, screen frame, cosmetic damage or to any other damage where such damage is caused by unauthorized modification, alteration, repairs to or service of the product by anyone other than an authorized MESCA service centre; physical abuse to or misuse of the product (including any failure to carry out any maintenance as described in the Owner’s Guide including air vent cleaning or any product damaged by excessive physical or electrical stress); normal wear and tear, or image retention caused by prolonged display of static images; any products that have had a serial number or any part thereof altered, defaced or removed; product use in any manner contrary to the Owner’s Guide; freight damage; or any damage caused by acts of God or other factors beyond the reasonable control of MESCA, such as power surge damage caused by electrical system or lightning. This limited warranty also excludes service calls or related services where no defect in the product covered under this warranty is found, service calls related to unsatisfactory audio or visual reception or signal unless caused by a defect in the product that is covered under this limited warranty, all costs, expenses or any other damages arising from product installation, removal from or re-installation into custom installations or on wall mountings or set-ups, any adjustments of user controls (including contrast, brightness, color, tint, fine tuning, sharpness), other adjustment necessary to prepare the unit for display or use, connection with any external devices, antenna, cable or satellite systems; or products purchased, used or located outside of Canada.

3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY WHICH, BUT FOR THIS PROVISION, MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR ANY PARTICULAR PURPOSE.

4. UNDER NO CIRCUMSTANCES SHALL MESCA BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY, BREACH OF CONTRACT, OR OTHERWISE.

5. Some jurisdictions do not allow the exclusion or limitation of incidental, special, or consequential damages, or the exclusion of implied warranties, so the above limitations or exclusions may not apply to you.

6. This limited warranty gives you specific legal rights, and you may also have other rights which vary from province to province.

MITSUBISHI ELECTRIC SALES CANADA INC. 4299 14th Avenue Markham, ON www.MitsubishiElectric.ca

In the U.S. call 1(877) 675-2224 for assistance.

92 Index

Index

Accent Lighting 40 Activity Menu 25

Automatic Generation 46 Change Input Name 45 Customizing 45 NetCommand-Controlled Switch-

ing of A/V Receiver Inputs 53

Removing a Disconnected HDMI

Device 45 Anamorphic Picture Format 28 Antenna Input (ANT) 19

Signal Strength for Digital Chan-

nels 27 Audio Lock (A/V receiver control) 65 Audio Output Jacks 19, 20 Auto Input Sensing 13 Auto-Off (Sleep Timer) 25 Auto-On (Timer) 43 A/V Receiver

and Speakers Option 39 and TV’s Remote Control 64 Audio Lock 65 Connecting 20, 24 Controlling Sound Volume 26 Disconnecting Analog 26 NetCommand IR Control 56, 57

Controlling a Device Connected

to the A/V Receiver 36, 61

Video and Audio Switching via

HDMI 61

Batteries 6 Blue Glow 40 Brightness (picture adjustment) 38

Cable Box

and TV’s Remote Control 64

Connecting 21, 22, 23 Captions Menu 42 CEC (Consumer Electronics Control)

36, 73

A/V Receiver 26, 74, 82

Troubleshooting 79 Channels

antennaweb.org 44

Physical/Virtual Channel Num-

bers 44 Scan (memorize) 12, 44 Troubleshooting 80

ChannelView™ Channel Listings 26 Cleaning 76 Clock, Set Date and Time 43 Closed Captions 42

Color Adjustments 41

Reset Color 41, 77

Computer

and Display Formats 17

Connecting 16 Contrast 38 Control Panel 9 Control Panel Lock 9, 49

Date.

See

Clock Default Settings, Returning to 77 DIGITAL AUDIO OUT 20 Dolby Digital 20, 59 DVD Player

and TV’s Remote Control 64 Connecting 21, 22

DVI Device, Connecting 22

Energy Usage 44

Fan Noise 4 Fast Power On 44 Film Mode 40 Font (digital closed captions) 42 FORMAT (aspect ratio, MORE menu)

28 Freeze Picture (PAUSE key) 8 Front Panel

Blue Glow Accent Lighting 40 Controls 9

Game

3D Video 29 Game Picture Mode 38 HDMI Cables for Games 20

GUIDE Key

ChannelView 26 HDMI Control 75 NetCommand Control 53, 55

HD (High-Deﬁnition) Signal) 28 HDMI

Changing Out an HDMI Device

and Auto Input Sensing 13

Connecting an HDMI Device 21

A/V Receiver with HDMI 24

HDMI Cable Categories 20 HDMI Control of CEC Devices 73 HDMI Jack 20 Removing an HDMI Device from

the Activity Menu 45

Headphones

Jack 20 Speakers Option 39

INFO Key

ChannelView 26

USB Menu 31 Internet Video 34 IR Emitter Placement 51 IR NetCommand Output (jack) 19

Language

Changing the Menu Language

43 in Digital Programs 39 SAP (Second Audio Program) 39

Laser Safety 3 Learn 45.

Control Letter Box Image Display 28 Level Sound 39 Listen To 39 Listings 26 Lock TV

Mitsubishi L75-A81, L75-A91 User Guide

Specifications and Main Features

Frequently Asked Questions

User Manual