Mitsubishi FB18KT, FB16KT, FB20KT Service Manual
Service Manual
99719-5A100
For use with FB16KT-FB20KT Chassis Service Manual.
Controller
FB16KT EFB4A-00011-up
FB18KT EFB5A-00011-up
FB20KT EFB5A-50001-up
FOREWORD
This service manual is a guide to servicing of Mitsubishi forklift trucks. The instructions are
grouped by systems to serve the convenience of your ready reference.
Long productive life of your forklift trucks depends to a great extent on correct servicing — the
servicing consistent with what you will learn from this service manual. We hope you read the
respective sections of this manual carefully and know all the components you will work on
before attempting to start a test, repair or rebuild job.
The descriptions, illustrations and specifications contained in this manual were of the trucks of
serial numbers in effect at the time it was approved for printing. Mitsubishi reserves the right to
change specifications or design without notice and without incurring obligation.
Pub. No. 99719-5A100
Safety Related Signs
The following safety related signs are used in this service
manual to emphasize important and critical instructions:
Indicate a specific potential hazard
resulting in serious bodily injury or
death.
Indicate a specific potential hazard
resulting in bodily injury, or damage
to, or destruction of, the machine.
Indicates a condition that can cause
damage to, or shorten service life of,
the machine.
NOTE
WARNING
!
CAUTION
!
The serviceman or mechanic may be unfamiliar with
many of the systems on this truck. This makes it
important to use caution when performing service
work. A knowledge of the system and/or components
is important before the removal or disassembly of any
component.
Because of the size of some of the truck components,
the serviceman or mechanic should check the weights
noted in this Manual. Use proper lifting procedures
when removing any components.
Following is a list of basic precautions that should
always be observed.
1. Read and understand all warning plates and decals
on the truck before operating, lubricating or
repairing the product.
2. Always wear protective glasses and protective
shoes when working around trucks. In particular,
wear protective glasses when pounding on any part
of the truck or its attachments with a hammer or
sledge. Use welders gloves, hood/goggles, apron
and other protective clothing appropriate to the
welding job being performed. Do not wear loosefitting or torn clothing. Remove all rings from
fingers when working on machinery.
3. Do not work on any truck that is supported only by
lift jacks or a hoist. Always use blocks or jack
stands to support the truck before performing any
disassembly.
4. Lower the forks or other implements to the ground
before performing any work on the truck. If this
cannot be done, make sure the forks or other
implements are blocked correctly to prevent them
from dropping unexpectedly.
5. Use steps and grab handles (if applicable) when
mounting or dismounting a truck. Clean any mud
or debris from steps, walkways or work platforms
before using. Always face truck when using steps,
ladders and walkways. When it is not possible to
use the designed access system, provide ladders,
scaffolds, or work platforms to perform safe repair
operations.
6. To avoid back injury, use a hoist when lifting
components which weigh 23 kg (50 lb.) or more.
Make sure all chains, hooks, slings, etc., are in
good condition and are of the correct capacity. Be
sure hooks are positioned correctly. Lifting eyes
are not to be side loaded during a lifting operation.
7. To avoid burns, be alert for hot parts on trucks
which have just been stopped and hot fluids in
lines, tubes and compartments.
8. Be careful when removing cover plates. Gradually
back off the last two bolts or nuts located at
opposite ends of the cover or device and pry cover
loose to relieve any spring or other pressure, before
removing the last two bolts or nuts completely.
9. Be careful when removing filler caps, breathers and
plugs on the truck. Hold a rag over the cap or plug
to prevent being sprayed or splashed by liquids
under pressure. The danger is even greater if the
truck has just been stopped because fluids can be
hot.
SAFETY
The proper and safe lubrication and
maintenance for this forklift truck,
recommended by Mitsubishi forklift truck, are
outlined in the OPERATION & MAINTENANCE
MANUAL for these trucks.
Improper performance of lubrication or
maintenance procedures is dangerous and
could result in injury or death. Read and
understand the OPERATION & MAINTENANCE
MANUAL before performing any lubrication or
maintenance.
WARNING
!
Do not operate this truck unless you have read
and understand the instructions in the
OPERATION & MAINTENANCE MANUAL.
Improper truck operation is dangerous and
could result in injury or death.
WARNING
!
WARNING
!
10. Always use tools that are in good condition and be
sure you understand how to use them before
performing any service work.
11. Reinstall all fasteners with same part number. Do
not use a lesser quality fastener if replacements are
necessary.
12. If possible, make all repairs with the truck parked
on a level, hard surface. Block truck so it does not
roll while working on or under truck.
13. Disconnect battery and discharge any capacitors
(electric trucks) before starting to work on truck.
Hang “Do not Operate” tag in the Operator’s
Compartment.
14. Repairs, which require welding, should be
performed only with the benefit of the appropriate
reference information and by personnel adequately
trained and knowledgeable in welding procedures.
Determine type of metal being welded and select
correct welding procedure and electrodes, rods or
wire to provide a weld metal strength equivalent at
least to that of parent metal.
15. Do not damage wiring during removal operations.
Reinstall the wiring so it is not damaged nor will it
be damaged in operation by contacting sharp
corners, or by rubbing against some object or hot
surface. Place wiring away from oil pipe.
16. Be sure all protective devices including guards and
shields are properly installed and functioning
correctly before starting a repair. If a guard or
shield must be removed to perform the repair work,
use extra caution.
17. Always support the mast and carriage to keep
carriage or attachments raised when maintenance
or repair work is performed, which requires the
mast in the raised position.
18. Loose or damaged fuel, lubricant and hydraulic
lines, tubes and hoses can cause fires. Do not bend
or strike high pressure lines or install ones which
have been bent or damaged. Inspect lines, tubes
and hoses carefully. Do not check for leaks with
your hands. Pin hole (very small) leaks can result
in a high velocity oil stream that will be invisible
close to the hose. This oil can penetrate the skin
and cause personal injury. Use cardboard or paper
to locate pin hole leaks.
19. Tighten connections to the correct torque. Make
sure that all heat shields, clamps and guards are
installed correctly to avoid excessive heat, vibration
or rubbing against other parts during operation.
Shields that protect against oil spray onto hot
exhaust components in event of a line, tube or seal
failure, must be installed correctly.
20. Relieve all pressure in air, oil or water systems
before any lines, fittings or related items are
disconnected or removed. Always make sure all
raised components are blocked correctly and be
alert for possible pressure when disconnecting any
device from a system that utilizes pressure.
21. Do not operate a truck if any rotating part is
damaged or contacts any other part during
operation. Any high speed rotating component that
has been damaged or altered should be checked for
balance before reusing.
22. When handling the parts containing asbestos, be
careful not to inhale the asbestos. Doing so is
hazardous to your health.
If the shop dust may contain asbestos, follow the
precautions described below.
a. Do not use compressed air for cleaning.
b. Do not brush or apply grinder on asbestos
containing materials.
c. To clean asbestos containing materials, wipe
with moistened cloth or use a vacuum cleaner
with particle filter.
d. If you have to handle the parts containing
asbestos for a long time, be sure to do it in a
well-ventilated area.
e. If the asbestos in the air cannot be removed,
wear a mask.
f. Be sure to observe the working rules and
regulations.
g. When disposing of materials with asbestos, be
sure to observe the environmental protection
regulations of your area.
h. Avoid working in the atmosphere where
asbestos particles may be suspended.
HOW TO USE THIS MANUAL
(Removal, Installation, Assembly and Disassembly)
Disassembly diagram (example)
Suggestion for disassembling
1. Output shaft, Removing
Remove output shaft using a special tool.
Service Data
A: Standard Value
B: Repair or Service Limit
209603
Sequence
1 Cover , Bolt, Washer (part name)
2 Snap ring ................ (part name)
A
0.11 to 0.28 mm
Gear Backlash
(0.0043 to 0.0110 in.)
B 0.5 mm (0.020 in.)
209604
Disassembling sequence
Procedures are described in the text.
2
1
Symbols or abbreviation
OP Option
R1/4 Taper pipe thread (external) 1/4 inch (formerly PT1/4)
Rc1/8 Taper pipe thread (internal) 1/8 inch (formerly PT1/8)
G1/4A Straight pipe thread (external) 1/4 inch (formerly PF1/4-A)
Rp1/8 Straight pipe thread (internal) 1/8 inch (formerly PS1/8)
Units
1. SI Units are used in this manual.
2. The following table shows the conversion of SI unit and customary unit.
Item SI unit Customary unit
Force
1 N 0.1020 kgf
(1 lbf) (0.4536 kgf)
Pressure
1 kPa 0.0102 kgf/cm
2
(1 psi) (0.0703 kgf/cm2)
Torque
1 N·m 0.1020 kgf·m
(1 lbf·ft) (0.1383 kgf·m)
GROUP INDEX Items
MAIN CONTROLLER
Controller components, Inspection and adjustment, Service data
TROUBLESHOOTING
Faulty central vehicle monitor system, Faulty diagnosis indication,
FOR CONTROL
or Other abnormalities
CIRCUITS
MOTORS Drive motor, Pump motor, EPS motor
GROUP INDEX
1
2
3
Outline ....................................................................................................... 1 – 1
Controller Components (Part 1) ......................................................... 1 – 2
Controller Components (Part 2) ......................................................... 1 – 3
Logic Card Components ...................................................................... 1 – 4
Controller Models ................................................................................... 1 – 5
Operation Outline ................................................................................... 1 – 6
Drive System ........................................................................................... 1 – 6
Neutral Position ........................................................................................ 1 – 6
Powering ................................................................................................... 1 – 6
Drive Motor’s Current Table (48 V type) ..................................................... 1 – 7
Regeneration ............................................................................................ 1 – 9
Steering and Turns .................................................................................... 1 – 9
Lever Regeneration Characteristic (48 V type)........................................... 1 – 10
Auto Regeneration Characteristic (48 V type) ............................................ 1 – 11
Steering Characteristic (1.6 ton type) ........................................................ 1 – 12
Steering Characteristic (1.8 ton type) ........................................................ 1 – 13
Steering Characteristic (2.0 ton type) ........................................................ 1 – 14
Hydraulic System ................................................................................... 1 – 15
Manual Control Model ............................................................................... 1 – 15
Finger-tip Control Model ........................................................................... 1 – 15
Fail-safe System ..................................................................................... 1 – 16
Output Power Control at Low Battery Voltage ........................................... 1 – 16
Overheat ................................................................................................... 1 – 17
Brush Wear ............................................................................................... 1 – 17
Maximum Vehicle Speed Control (SUO #7) .............................................. 1 – 17
Output Power Control During Braking ....................................................... 1 – 17
Chat Timer (SUO #24) .............................................................................. 1 – 17
Seat Switch Timer (SUO #25) ................................................................... 1 – 17
Malfunction Detection (Run Time Diagnosis) ................................. 1 – 17
1
MAIN CONTROLLER
Malfunction Data Record (History Folder) ....................................... 1 – 18
Data Storage ............................................................................................ 1 – 18
Review of Stored Data .............................................................................. 1 – 18
Setting ....................................................................................................... 1 – 18
Printed Circuit Board Settings ................................................................... 1 – 18
Adjustment of Remaining Battery Level .................................................... 1 – 18
Setup Options ........................................................................................... 1 – 19
Self-diagnosis ......................................................................................... 1 – 19
Other Functions ...................................................................................... 1 – 20
Display Unit .............................................................................................. 1 – 20
BDI (Battery Discharge Indicator) ............................................................. 1 – 20
Hourmeters and Time Display ................................................................... 1 – 20
Vehicle Speed and Error Code Display ..................................................... 1 – 21
Action Lights (LEDs) ................................................................................. 1 – 21
Inspection and Adjustment ................................................................. 1 – 30
Inspection and Adjustment Tools .............................................................. 1 – 30
Removal and Installation of Logic Card ..................................................... 1 – 30
Tightening of High-tension Cable Terminals .............................................. 1 – 31
Component Testing ................................................................................... 1 – 32
Service Data ............................................................................................ 1 – 73
Tightening Torque .................................................................................. 1 – 77
1-1
MAIN CONTROLLER
Outline
Main controller
The main controller is the heart of the forklift truck
operating system.
The logic card contains judgment-making functions, and is
equipped with a battery discharge indicator and a
malfunction diagnostic function.
The main controller is used to operate the drive motors,
pump motor and power steering system.
Logic card
The logic card is a printed circuit board located on the main
controller panel. Most of the circuits on the board are used
to control input and output voltages to and from the
microprocessor.
Microprocessor (MPU)
The software in the microprocessor controls the drive
system, pump motor and central vehicle monitor system
(CVMS).
Selector Switches
They are used for setting the BDI and selection of some
options.
206793A
206794
Loading...