Mitsubishi Electronics F7500, 164, EYS User Manual

IMMERSIVE SOUND LED LCD HDTV

with Integrated Sound Projector

MODELS

154 Series 164 Series

265 Series

OWNER’S GUIDE

For questions:•

Visit our website at www.mitsubishi-tv.com. E-mail us at MDEAservice@mdea.com. Call Consumer Relations at - 800-332-2119 for operational or connection assistance.

For information on • System Reset, please see the back cover. To order replacement or additional remote controls, visit our website at www.mitsuparts.com or call •

800-553-7278. 265 Series.• IR emitter cables for NetCommand home-theater control are available for purchase from

Mitsubishi. number 299P254020 (four-ended cable).

Call 800-553-7278 and

request either part number 242D483020 (two-ended cable) or part

Downloaded From TV-Manual.com Manuals

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilat-

eral triangle is intended to alert the user to

the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

WARNING: T socket outlet with a protective earthing connection.

MAINS DISCONNECTION: The mains plug is used as the disconnect device. The mains plug shall remain readily operable.

WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

This apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

WARNING: This product contains chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm.

TV WEIGHT: This TV is heavy. Exercise extreme care when lifting or moving it. Lift or move the TV with a minimum of two adults. To prevent damage to the TV, avoid jarring or moving it while it is turned on. Always power off your TV, unplug the power cord, and disconnect all cables before moving it.

Note: Features and specifications described in this owner’s guide are subject to change without notice.

his product shall be connected to a MAINS

FCC Declaration of Conformity

Product: LCD Flat Panel HDTV Models: LT-55154

LT-40164, LT-46164, LT-55164 LT-46265, LT-55265

Responsible Party:

Telephone: (800) 332-2119

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and

(2) This device must accept any interference

received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and the receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by Mitsubishi could cause harmful interference and would void the user’s authority to operate this equipment.

Mitsubishi Digital Electronics America, Inc. 9351 Jeronimo Road Irvine, CA 92618-1904

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

Contents

Important Information About Your TV

Installation and Operating Notes ............. 4

Important Safety Instructions ................ 5

Stand Installation ......................... 6

Wall-Mounting ........................... 7

1 Basic Setup and Operation

Package Contents ....................... 9

Before You Begin ....................... 10

First-Time Power-On ..................... 10

TV Controls ........................... 11

Remote Control ..................... 11

The TOOLS Key and Menu ............. 12

TV Control Panel .................... 13

POWER Indicator .................... 13

Setting Up TV Inputs..................... 14

Basic TV Operation...................... 16

Using the TV with a Personal Computer ....... 19

2 TV Connections

Before You Begin ....................... 21

Connection Types and Audio/Video Quality .... 21

Inputs and Outputs ...................... 22

Cable Routing ......................... 22

DMI Device .............................24

Y Pb Pr Component Video Device ........... 25

DVI Video Device ....................... 25

Antenna or Cable TV Service ............... 26

Composite Video Device .................. 26

VCR or DVD Recorder to an Antenna or

Wall Outlet Cable ...................... 26

A/V Receiver .......................... 27

A/V Receiver with HDMI Output ............. 27

Supplemental Audio Connections ......... 28

3 TV Features

Sleep Timer ........................... 29

FAV (Favorite Channels) ................... 29

ChannelView Channel Listings .............. 30

Status Display ......................... 31

Using an External Sound System ............ 32

Picture Shape and Display Formats .......... 33

Camera Images and Music Files ............ 34

USB Source Devices .................. 34

Photos and Motion Video as

Composite Video ................... 36

Using an Audio-Only Device ............ 36

Wireless Audio Playback ............... 37

Sound Projector ........................ 38

StreamTV™ Internet Media ................ 42

Introduction to Home-Theater Control ........ 45

4 TV Menus

Main Menu ............................ 46

Picture............................... 46

Sound ............................... 49

Captions ............................. 51

Setup ............................... 52

Inputs ............................... 55

Lock ................................ 57

5 NetCommand IR Control

About NetCommand IR Control ............. 60

IR Emitters ............................ 61

NetCommand Setup ..................... 62

Operating NetCommand-Controlled Devices ... 63

6 NetCommand IR Control of an A/V Receiver

Controlling an A/V Receiver after NetCommand

Setup .............................. 67

Setting Up A/V Receiver Control

Power and Volume ................... 68

Automatic Audio/Video Switching Over

an HDMI Connection ................. 69

Appendices

Appendix A: Programming the Remote Control . 73

Appendix B: Bypassing the Parental Lock ..... 79

Appendix C: HDMI Control of CEC Devices .... 81

Appendix D: TV Care .................... 84

Appendix E: Troubleshooting .............. 85

Trademark and License Information .......... 92

Warranty .............................. 99

Network Service Disclaimer ............... 100

Index ................................ 101

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

Important Information About Your TV

For Your Records

Record the model number, serial number, and purchase date of your TV. The model and serial numbers are on the back of the TV. Refer to this page when requesting assistance with the TV.

MODEL NUMBER SERIAL NUMBER PURCHASE DATE RETAILER NAME LOCATION

Installation and Operating Notes

Custom cabinet installation must allow for proper air circulation around the television.

NOTE TO CATV SYSTEM INSTALLER: THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR THE PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL.

If Your TV Gets Damaged

Crystalline liquid may leak from the LCD panel and broken glass may be scattered.

CAUTION: The crystalline liquid is toxic. Avoid contact with your skin, eyes, or mouth. DO NOT

touch the broken glass or crystalline liquid. DO NOT get glass fragments or crystalline liquid into eyes or mouth. Should either contact your eyes or mouth,

rinse the contacted area thoroughly with water and consult your doctor.

Disposal of Your TV

The LCD panel contains a small amount of crystalline liquid which is toxic and should not be touched.

DO NOT dispose of the TV with general household waste. For disposal or recycling information, contact

your local authorities or the Electronic Industries Alliance at www.eiae.org.

TV Software

Do not attempt to update the software of this TV with software or USB drives not provided by or authorized by Mitsubishi Digital Electronics America, Inc. Nonauthorized software may damage the TV and will not be covered by the warranty.

Children and TV Viewing

The American Academy of Pediatrics discourages television viewing for children younger than two years of age.

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

AN TE NN A LE AD IN W IR E

AN TE NN A DIS C HA R G E UNI T (N E C AR T IC LE 8 10-20 )

G R OU NDI NG C OND UC TO R S (N E C AR T IC LE 8 10-21 )

G R OU ND CL AMP S

P OW E R S E R VIC E G R OUN DING E LE C TR O DE S YS T E M (N E C AR T 2 50, PA R T H)

G R OU ND CL AMP

E LE C TR IC S E R V ICE E QU IPM EN T

NE C — N AT IO NAL E LE C TR IC AL C ODE

E XA MP LE O F AN T E N NA G R OU N DIN G

Important Safety Instructions

Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges.

Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

Extension pieces on back of stand

CAUTION.

Place the stand in the foam insert with the extension pieces facing away from the TV. Otherwise, the TV will be damaged in transit.

Protect the TV and stand with the original packing material.

DON’T place your hand where it can get caught under the TV.

DO support the TV

under the corners.

TV in protective

wrapping

Extension pieces on stand must face out, away from TV.

Repacking the Stand

Two adults are required to lift the TV.

BACK

Stand Installation

CAUTION

Using this TV with other than the authorized accessories may cause the TV to become unstable, which • can cause damage to the product or possible injury.

At least TWO PEOPLE are required to install the stand. Support the TV near the corners as shown. Failure to follow • these recommendations may result in personal injury and damage to the product.

Note

40- or 46-inch TV:• If planning to wall-mount the TV, there is no need to install the stand. 55-inch TV: • The TV comes from the factory with the stand pre-installed.

Required: Phillips Screwdriver

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

5BCMF

1SPUFDUJWF TIFFU

4UBOE

55-inch TVs

(6 screws)

40- and 46-inch TVs

(4 screws)

Protective

Sheet

Pull stand to remove.

Wall-Mounting

To order a wall-mount kit, please contact Peerless Industries, Inc. at (800) 473-3753 or visit www.peerlessmounts.com. Order wall-mount kit model ST650.

To order a wall-mount kit from Mitsubishi Digital Electronics America, Inc., please visit www.mitsuparts.com or call (800) 553-7278.

Complete installation instructions are included with the kit.

Stand Removal Prior to Wall-Mounting

CAUTION At least TWO PEOPLE are needed to safely remove the stand. Have one person hold the TV while the other person removes the stand. Failure to follow these recommendations may result in personal injury and damage to the product.

Note

55-inch TV: • Remove the factory-installed stand prior to wall-mounting. 40- or 46-inch TV:• If you installed the stand for table-top use, follow these instructions to remove it prior

to wall-mounting the TV.

Disconnect the TV’s AC power cord from the AC

power outlet. Spread the protective sheet that was wrapped

around the TV on a flat, even surface, such as a sturdy table. The protective sheet will help prevent damage to the display.

IMPORTANT: To avoid damaging the screen, make sure there are no foreign objects under or on top of the protective sheet.

Position one person on each side of the TV (left and

right sides). Have each person firmly grasp their side of the TV and gently place it face down on the protective sheet with the display stand hanging over the edge of the table. See the illustration to the right.

Use a magnetic philips screwdriver to remove the

stand screws from the recessed holes (see illustration to right). Note: A regular screwdriver can be used with a separate magnetic pick-up tool.

While one person holds the TV with both hands,

have the other person grasp the stand (see illustration to the right) and remove the stand by pulling it away from the TV in the direction of the large arrow shown in both illustrations.

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

Special Features of Your TV

Your new high-definition widescreen television has

many special features that make it the perfect center of your home entertainment system, including:

1080p High-Definition LCD Display System

Your Mitsubishi LED LCD HDTV uses a full 1920 x 1080

LCD panel to create the picture you see on the screen. All images are displayed at 1080p. The TV uses new Plush

1080p® 5G digital video processing to convert lower-reso-

lution signals to 1080p for display.

True120Hz and True240Hz

True120Hz (154 and 164 series) and True240Hz (265 series)

make fast-moving images appear smoother and more fluid, free from motion blur. It does this by doubling the traditional progressive scan frame rate and creates new frames of video between the traditional frames to create smoother moving images. True120Hz/True240Hz also smooth film judder (image vibration) that may be present in film-based content such as movies.

16:9 Widescreen Picture Format

Enjoy a full theatrical experience in the comfort of your home. View pictures as film directors intended them. Digital TV broadcasts, DVDs and newer video game consoles support this widescreen format.

Integrated HDTV Tuner

Your widescreen Mitsubishi HDTV has an internal HDTV

tuner able to receive both over-the-air HDTV broadcasts (received via an antenna) and non-scrambled digital cable broadcasts, including non-scrambled HDTV cable programming.

High-Definition Video Inputs

Component Video Inputs.• Also called Y/Pb/Pr

inputs, these inputs receive standard analog video formats of 480i, 480p, 720p, and 1080i high-definition signals. This provides a high level of flexibility when connecting DVD players/recorders, cable boxes, and satellite receivers.

HDMI Inputs.• These inputs accept digital 480i, 480p, 720p, 1080i, and 1080p video signals plus bitstream and PCM digital stereo signals. The HDMI™ inputs can also accept a variety of PC signals and resolutions.

Used with an adapter, these inputs also accept compatible digital DVI video signals. HDMI inputs provide additional high-performance, high-definition connections for maximum flexibility in your choice of home theater products. The HDMI inputs are HDCP copy-protection compatible.

Easy Connect Auto Input Sensing

Easy Connect™ Auto Input Sensing automatically recognizes when you plug in a device and prompts you to assign a name to it.

Home-Theater Control

HDMI Control

Available on all models. HDMI devices with Consumer Electronics Control (CEC) capabilities may be compatible with the TV’s HDMI Control feature. Compatible devices can receive control signals through the HDMI connection, allowing the TV’s remote control to operate some functions of these devices.

NetCommand with IR Learning

265 Series. NetCommand® supports IR (infrared) control of products such as VCRs, DVD players, cable boxes, and satellite receivers. NetCommand can “learn” remote control signals directly from many devices, allowing you to create a customized NetCommand-controlled hometheater system.

Sound Projector

Sound Projector technology uses the TV’s bank of speakers to create a simulated surround sound effect by reflecting sound off the room walls.

StreamTV™ Internet

StreamTV brings many popular internet applications to your TV. Among them is the VUDU™ movie service, offering the largest on-demand HD movie selection anywhere, featuring full 1080p and 5.1 surround sound. VUDU allows you to enjoy movies with no store visits, no mailing, no late fees and no subscriptions.

ENERGY STAR

This is an ENERGY STAR® qualified TV. Products that earn the ENERGY STAR prevent greenhouse gas emissions by meeting strict energy efficiency guidelines set by the U.S. Environmental Protection Agency and the U.S. Department of Energy.

This TV uses power within ENERGY STAR guidelines except when Picture Mode is set to Brilliant.

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

Basic Setup and Operation

Package Contents

Please take a moment to review the following list of items to ensure that you have received everything.

Remote Control

Two AA Batteries

Installing the Remote Control Batteries

Remove the remote control’s back cover by

gently pressing in the tab and lifting off the cover.

Load the batteries, making sure the polarities

(+) and (-) are correct. For best results, insert the negative (-) end first.

Snap the cover back in place.

Basic Owner’s Guide

Quick Setup Guide

Product Registration Card

Power Cord

Cable Ties

The remote control requires two AA alkaline batteries.

Stand Screws (40- and 46-inch TVs only)

265 Series. Calibration Microphone

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

10 1. Basic Setup and Operation

Before You Begin

Review the important safety, installation, and oper-

ating information at the beginning of this book. Choose a location for your TV.

• See the stand-installation or wall-mounting requirements starting on page 6.

• Allowatleastfourinchesofspaceonallsides

of the TV to help prevent overheating. Overheating may cause premature failure of the TV.

• Avoidlocationswherelightmayreflectoffthe

screen.

Install the batteries in the remote control.

Plug the TV into an AC power outlet.

First-Time Power-On

Press the

ensure that the remote control is in TV mode.

Aim the emitter end of the

remote control at the TV and press the

Wait for the Welcome

screen.

If you wish to change the

menu language to Español, press .

Press

energy-mode selections. Select Home.

key to

POWER

key

to move to the

TV power connection

TV Tips

Turning the TV On or Off

Point the emitter (bulb) end of the remote • control at the front of the TV and press the

POWER

button. Press the • panel.

Controlling Sound Volume

Press • See also • “Controlling A/V Receiver Sound Volume” on page 32.

POWER

button on the TV control

VOL

to adjust the sound level.

Press

Press menu.

Welcome Screen Energy Options

This table compares energy choices offered in the Welcome screen.

Picture Mode Bright Brilliant Backlight Level

to highlight EXIT.

ENTER

to clear the

Mitsubishi recommends the • Home setting, which uses power within ENERGY STAR® guidelines.

The • Retail setting looks best under bright lighting. In this mode, the TV uses power in excess of ENERGY STAR guidelines.

Home Retail

Reduced Brightness

Full Brightness

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

1. Basic Setup and Operation 11

TV Controls

Remote Control

For more on use and care of the remote control, see page 84.

Emitter (Bulb) End

MUTE

TOOLS

VOL

PAGE

ENTER

Sleep Timer, page 29

Number/letter keys

Channel tuning, page 16 Pass-code entry, page 57, page 43

Adds a separator in digital channel numbers. Clears some menu entries.

Mutes the TV speakers.

Displays shortcuts for the number keys. Press to check if shortcuts are available for the current device. See the next page.

Controls volume of TV speakers.

Changes channels; moves to another page in a menu or list.

Selects a channel number or menu item.

Navigation and adjustment controls

TV CAB/SAT DVD AUDIO VCR

ress the key for the device type to control. Leave in TV mode for normal TV viewing.

Powers TV on or off.

Returns to the previous channel;

LAST

moves back one menu

FAV

FO R M AT

INTERNET

INPUT

AUDIO

Displays up to nine favorite sources, page 29.

Changes picture shape, page 18

Connects to StreamTV internet content, page 42.

Press to select a TV input, page 16.

Audio settings, page 49

GUIDE

Record/Playback controls for external devices

When remote control is programmed, page 73 HDMI control, page 83

265 Series: With NetCommand, page 66

Note: To operate other audio/video devices using the

• SeeAppendix A, “Programming the Remote

• ForHDMIdevicescompatiblewiththeTV’sHDMI

ChannelView listings, page 30

INFO

TV status or TV help.

(

PAUSE) Freezes a broadcast TV picture.

TV’s remote control, use any of these methods:

Control.”

Control feature, see Appendix C.

• 265 Series

See - page 60 for NetCommand IR “Learning” of device keys. For use of specific keys with NetCommand- controlled devices, see “Special Operation Methods,” page 64.

VIDEO

EXIT

F1–F4. 265 Series. Special keys for

use with NetCommand IR control. See “Initial NetCommand Setup”.

Video settings, page 46

Displays or clears the TV main menu (page 46). back one menu.

Clears all menus.

Also steps

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

12 1. Basic Setup and Operation

TOOLS

TV Controls, continued

The TOOLS Key and Menu

TOOLS

Press the for common functions. Press the number key to activate the shortcut. See the sample menu below.

TOOLS

key to check for shortcuts. The Tools menu lists shortcut keys

Shortcuts specific to the current device are in the third column.• Shortcuts may be available for a CEC-enabled device. See • Appendix C,

“HDMI Control of CEC Devices,” page 81. 265 Series.• After setting up NetCommand control for a device, check the

Tools menu for shortcuts. See page 62.

PICTURE SOUND

Sample Tools menu

Picture Shortcuts

1 Picture Mode Brilliant page 46

4 Picture Mode Natural

164 and 265 Series. Brilliant and

Natural Picture Modes are the default choices. If your installer has set up special Picture Modes in the Picture > Advanced menu, select them from this menu.

7 Backlight turns off the backlight. Press any number key to turn the backlight back on.

page 48

---

Tools

Device-Specific Shortcuts

Availability varies, depending on equip-

Sound Shortcuts

2 Subwoofer. Turns on or off audio to a con-

nected subwoofer.

5 Surround. Selects Sound Mode Surround page 50

8 Night. Selects Sound Mode Night

ment features and setup.

3 CC. Turns closed captions on/off

page 51

page 50

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

1. Basic Setup and Operation 13

POWER

INPUT

ENTER

VOL

POWER

TV Controls, continued

TV Control Panel

Buttons on the control panel duplicate some keys on the remote control.

To display the main menu, press • simultaneously for about 10 seconds. Press and hold

INPUT

and

VOL+ for 10 seconds to clear the

menu. Refer to • left labels when no TV menus are dis-

played. Refer to • right labels when using TV menus or after

activating a special function.

INPUT

and

VOL+

System Reset

If the TV fails to respond to the remote control, the control-panel buttons, or will not power on/off, perform System Reset. Recent setting changes made before using System Reset may be lost.

To perform System Reset, press and hold the

POWER

button on the control panel for 10 seconds.

Panel-Lock Release

To • release the Panel Lock using the TV control panel, press and hold the

INPUT

button on the control panel for ten seconds. If the TV is off, press the

POWER

button to make it power on.

To activate the Panel Lock, use the • Lock menu, page 59.

TV control panel

POWER Indicator

Key

Off

Steady On Slow Blinking Fast Blinking

LED Color TV Condition

None

Green

TV is powered off. Normal operation.

TV is powered on. Normal operation.

TV powered off, auto-on TV Timer is set.

Normal operation. TV can be turned on at any time.

Red/ Yellow

TV may require service.

Hold power button on front panel for 10 seconds to reset TV.• If LED continues to flash red and yellow after reset, turn off the •

TV and unplug it from the AC power source. Wait one minute and then plug the set back in.

If LED continues to flash red and yellow,• www.mitsubishi-tv.com or call 1-800-332-2119 to receive Authorized Service Center information.

You may be asked to count how many times the LED flashes each color to assist in troubleshooting.

go to

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

14 1. Basic Setup and Operation

Setting Up TV Inputs

Using the ANT (Antenna) Input

If using an antenna or direct cable service (no cable box), connect the incoming coaxial cable to the TV’s

ANT

input. Refer to page 26.

You must perform a channel scan to enable reception of digital channels. If you skip this step, the TV will receive only analog channels. The channel scan

will search for high-definition and standard-definition channels available in your area.

Memorizing Channels with Channel Scan

For the ANT input

To start channel memorization

Power on the TV.

Press

Start channel memorization from the Setup > Channel menu.

and open the Setup > Channel menu.

Setting Up Inputs with Auto Input Sensing

Power on the TV.

Power on the devices to ensure detection.

Connect one device to the TV, making note of the

TV input jack. The TV will display the New Device Found screen if

the connection type is detectable. Highlight the device type in the on-screen list and

press

ENTER

. The name you select here will appear

in the Input Selection menu.

Press

Highlight

over-the-air antenna. Highlight Ant Cable for service over direct cable

(no cable box). Press check.

Select the scan type.

Highlight

Channel memorization may take up to 15 minutes to complete.

To stop channel memorization before completion, press

At any time after Channel Scan,

Use the • Setup > Channel > Edit menu (page 53) to add or delete individual channels from memory.

Perform an additive scan with the • New only option to add channels not already in memory.

Repeat the • All channels scan if you move the TV to a new geographic area with a different channel line-up or reposition the antenna.

to enter the menu.

Ant Air if connected to an

ENTER

to add a

For first-time setup, highlight • All channels. To scan for channels not already • in memory, highlight New only. Press

ENTER

to add a check.

Scan and press

CANCEL

ENTER

Sample New Device Found screen.

Important Note for NetCommand Users 265 Series. Be sure to select the correct device

type here. Although you can change the device type later using the Inputs > Name menu, any “learned” NetCommand IR codes will be erased when you make the change.

Press

EXIT

to close the New Device Found screen.

Repeat the preceding steps for each for each additional device you want to add.

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

1. Basic Setup and Operation 15

Setting Up TV Inputs, continued

About Auto Input Sensing

This TV’s Easy Connect™ Auto Input Sensing feature detects the following connections automatically:

Analog video jacks from inputs 1, 2, and 3• HDMI inputs (when powered on)•

• USB device containing photo and music files (JPG and MP3 formats).

Auto Input Sensing for Most Devices

When you first connect a device, the TV will:

a. Detect the connected device and automati-

cally switch to it. b. Prompt you to identify the device type. c. Repeat these steps for other newly detected

devices.

When You First Connect a Device

Most Device Types.• Select the device type from

the on-screen list. The device type you select here will appear as an icon in the Input Selection menu.

A/V Receiver. •

receiver, select AVR the A/V receiver is not recognized automatically.

For an HDMI-equipped A/V

from the list of device types if

Tips on Auto Sensing

Choose a different name for each input.• The antenna input (•

although you can turn off the unused antenna input in the Inputs > Name menu.

Change the device type displayed in the • Input Selection menu by using the Inputs > Name menu (page 55).

Some HDMI devices can automatically tell the TV • what name to use in the Input Selection menu and you will be unable to change the name.

The TV is unable to detect a new connection if • the current input is USB, Bluetooth®, or internet. Switch to a different input before connecting.

265 series.• Any “learned” NetCommand IR codes will be erased if you change the device type in the Inputs > Name menu.

Reactivating Auto Input Sensing for an HDMI Input

After you disconnect an HDMI device, Auto Input Sensing is temporarily disabled. Perform these steps:

ANT

) is never detected,

HDMI CEC Devices Compatible with the • TV’s HDMI Control Feature.

CEC-enabled HDMI-equipped devices are often recognized automatically by the TV. may allow you to control some functions of a CECenabled device. See Appendix C, “HDMI Control of CEC Devices.”

New Device Found screen for a device with HDMI control enabled. Select On if you want to enable the TV’s HDMI control of the device. In some cases, as in the example above, you will also be prompted to select a device name.

Compatible

HDMI Control

Disconnect the HDMI device.

Delete the removed HDMI device in the

Name menu (see “Removing an HDMI Device,”

page 83). Connect the new device and the

Found screen will display.

New Device

Inputs >

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

16 1. Basic Setup and Operation

Basic TV Operation

Selecting an Input to Watch

Press

Sample Input selection menu, DVD input selected

Press

To control the input device, use the device’s remote

control or see “Introduction to Home-Theater Control,” page 45.

Note: In most cases, to see a named icon for a con-

More About the Input Selection Menu

• Toassignhelpfulnamestotheicons,seethe

Inputs > Name menu, page 55.

• ToremoveunwantedAntenna,Bluetooth®, or HDMI

device icons from the Input Selection menu, see the Inputs > Name menu, page 55.

• Torearrangetheicons,seetheInputs > Order menu, page 56.

INPUT

and to highlight an input icon.

ENTER

to switch to the input.

nected device (as in the samples), you must ﬁrst assign a name either

• Whenthedeviceisfirstconnectedandthe

New Device Found menu offers a choice of names.

• ByusingtheInputs > Name menu to assign or change a name at any time after the TV has detected the connection.

Watching Broadcast TV

TV Connected to an Antenna or Direct Cable Service (no cable box)

Note: Perform channel memorization to enable recep-

tion of digital channels. See page 14.

Press

Sample Input Selection menu, antenna input selected

INPUT

to display the Input Selection menu.

Highlight the antenna or cable icon and press

To tune to a these methods.

Enter the channel number using the number • keys on the remote control and press

For a two-part digital channel, such as 3-1, press 3

Press • time.

Press and hold • Press • Use the Fav (Favorites) feature to tune to up to •

nine favorite channels. See page 29. Press •

listings, highlight a channel number, and press

ENTER

Set up ChannelView custom channel banks • and use the CH / key to tune to predefined groups of channels. See page 30.

channel from the

—

CANCEL

LAST

GUIDE

to tune.

1 ENTER

to change channels one channel at a

to speed through channels.

to return to the previous channel.

to display ChannelView channel

ANT

input, use any of

ENTER

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

1. Basic Setup and Operation 17

Basic TV Operation, continued

Picture Settings

To get the best picture under different viewing con-

ditions, set the Picture Mode first before changing other video settings. See page 46.

a. Press b. Press until Picture Mode

c. Press to make one of these selections:

Press

ment. Press

Press

Additional picture options are available through these menus:

VIDEO.

displays.

Name When to Use

Brilliant Game

Bright For most daytime viewing Natural For most nighttime viewing

to display the name of another adjust-

to make the adjustment.

EXIT

to clear the display.

Under bright light

With gaming consoles (inputs named

Game

or PC only)

Basic Audio Controls

Controlling Sound Volume

Press •

VOL

to adjust the sound level

of the TV speakers. Control •

on-screen slider Sound > Global > Subwoofer to On to make this adjustment available.

See also • “Controlling A/V Receiver Sound Volume” on page 32.

Changing Audio Settings (TV Speakers Only)

Press

ment you want. See page 49. Press

Changing the Audio Output

To switch from the internal TV speakers to an external sound system,

subwoofer volume with an

. See page 49. Set

AUDIO

to find the adjust-

to change.

Menu Name Page

Picture > Video 46

Picture > Picture Plus

Picture > Perfect Picture > Advanced (164 and 265 Series) 48

(265 Series)

47 48

Press

AUDIO

. Press Press

to display the TV Speakers option.

to change to Off.

TV Care

See page 84.

Assistance

For troubleshooting, service, and product support, • see Appendix E, starting on page 85.

For warranty information, see • page 99.

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

18 1. Basic Setup and Operation

Basic TV Operation, continued

The FORMAT Key and Picture Shape

Repeatedly press the

FORMAT

through displays for the current program. The TV will remember the format you last used on each input.

For details, see page 33

Black bars at the edges of the screen are common in HD pictures. Black bars are not a defect of the TV.

Black bars are added by broad-• casters to fill the 16:9 screen area while preserving the original aspect ratio of the picture.

Your cable box, satellite receiver, • or other device may also be altering the broadcast picture. If your device offers output in native format, try using it with Mitsubishi picture formats.

key to cycle

Important

Sample Uses of the

You can use the edges of the picture.

Squarish 4:3 image is narrower than the 16:9 screen; unused areas at the sides are filled with black.

Wide 2.35:1 anamorphic DVD image; unused areas at the top and bottom are filled with black (letterbox effect).

FO R M AT

key to reduce or eliminate black areas at the

Key

Press

Wide Expand mode stretches the picture sideways to fill the screen.

Press

Zoom mode. The picture fills the screen. All four edges are cropped in this mode.

More TV Features

Feature

Parental controls (Lock menu) 57

Audio Lock (controls your sound system with the TV’s remote control left in TV mode.)

TV Clock. Set the TV Clock if you plan to use the TV Timer (page 52) or ChannelView (page

30).

Favorite channels or sources 29

ChannelView and custom channel collections 30

Changing the input names that appear in the Input Selection menu (Inputs > Name menu)

Digital camera images and mp3 music files 34

164 and 265 Series. Listening to a wireless audio device with the TV speakers

StreamTV™ internet access 42

Page

Feature

Programming the remote control to operate other A/V devices

Controlling compatible devices using HDMI CEC control

265 Series. Controlling A/V devices with NetCommand

Page

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

1. Basic Setup and Operation 19

VGA

PC MONITOR OUT

Computer with

HDMI output

HDMI-to-HDMI cable

DVI OUT

AUDIO

OUT

Computer

with Digital

DVI output

DVI-to-HDMI

cable

Audio cable

Using the TV with a Personal Computer

Connecting a Computer to the TV

Use one of the connection methods listed below based on your computer’s video output.

Computer Video Output

Digital DVI DVI-to-HDMI cable

HDMI HDMI-to-HDMI

This TV accepts digital computer video signals only. This TV is not compatible with VGA (analog) computer video.

Connect the computer’s digital signal output to one

of the TV’s HDMI jacks. See the connection diagrams for the method suited to your equipment.

Connect the computer’s audio output using one of

these options:

• FordigitalDVIvideosignals,connectthe

analog audio output to the TV’s

INPUT

• ForHDMIsignals,noadditionalaudioconnection is required.

Video Connection

or an HDMI cable with a DVI-to-HDMI adapter

cable

IMPORTAN T

jack.

Audio

Connection

Analog audio cable with mini plugs

No additional audio connection is required.

DVI/PC AUDIO

DMI Connection

Mitsubishi recommends using high-speed HDMI cables to connect newer devices incorporating HDMI technology.

An HDMI-to-HDMI connection carries all video and

audio on a single cable.

HDMI and Digital Surround Sound

The TV’s HDMI inputs can receive digital surround sound from an HDMI device. Use an HDMI connection if you want to hear digital surround sound from the TV’s internal speaker array.

DVI Video Connection

Note: If you are unable to hear audio from the

computer, there may be an incompatibility in

the computer’s hardware, software, or internal settings. Consult a trained computer technician for advice.

Power on the TV and computer. The TV will detect

the connection and display the New Device Found screen.

In the

Note:

Downloaded From TV-Manual.com Manuals

New Device Found screen, press to

highlight PC in the list of device types. It is important to use the name PC so that the TV processes the PC signal correctly.

Highlight Device Found screen.

EXIT and press

If your computer provides digital audio output (coaxial or optical), you can connect it directly to a digital A/V receiver and bypass the TV.

ENTER

to close the New

A DVI connection from a personal computer requires a separate audio connection.

For assistance call 1(800) 332-2119

20 1. Basic Setup and Operation

Using the TV with a Personal Computer

Computer Video Adjustments

Power on the computer.

Select

this, press move the highlight to the PC icon, and press

Working from the computer, change

the resolution of the computer image. View the computer image on the TV and maximize the computer resolution while maintaining a suitable aspect ratio for the image.

Perform TV video adjustments.

VIDEO

adjustment options. Press

picture shape best suited to the image. See the chart on this page showing how different computer resolutions can be displayed on the TV.

Distortion in Computer Images

Computer images may show distortion when viewed on the TV, e.g., lines that should be straight may appear slightly curved.

PC from the Input Selection menu. To do

INPUT

to open the Input Selection menu,

Press

repeatedly to access video-

FORMAT

repeatedly to find the

Image Resolution

Your Mitsubishi TV can display the resolutions shown in the chart from standard VGA (640 x 480) through 1920 x 1080 signals at a refresh rate of 60 Hz.

In most cases, the computer will select the best resolution match to display on the TV. You can override this setting if you wish. Refer to your computer operating system’s instructions for information on changing the screen resolution.

Tip

Set the computer’s screen saver to display a pattern after several minutes of inactivity. This acts as a reminder that the TV is powered on.

ENTER.

Computer Display Formats

Press

FORMAT

for your computer’s video signal.

Computer Signal

Original Format

VGA 640 X 480

SVGA 800 X 600

Original Format Standard Zoom

XGA 1024 X 768

PC 720p 1280 X 720

WXGA 1360 X 768

SXGA 1280 X 1024

Original Format Standard

PC 1080p 1920 X 1080

repeatedly to cycle through the TV displays available

As Displayed on TV Screen

4 X 3

Standard

16 X 9

Standard

Zoom

You may need to restart the computer for changes to take effect.

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

TV Connections

Component

GOODBEST

VIDEO QUALITY

AUDIO QUALITY

HDMI-to-DVIHDMI Video Video

Composite

L/R Analog

AudioAudio

Digital

HDMI

Stereo

Mini-Plug

Before You Begin

Auto Input Sensing

The TV’s Auto Input Sensing feature automatically recognizes many connections and prompts you to identify the type of device connected. See page 15 for more on Auto Input Sensing.

Connection Types

Use the connection types available on your input devices that will give the best video quality. For example, choose HDMI over component video; choose component video over composite video.

Picture Quality

For best picture quality, route signals directly from the source device to the TV whenever possible.

Connection Types and Audio/Video Quality

Surround Sound

To use the surround sound capabilities of the TV’s • speaker array, you must connect the digital surround sound source to the TV on either

An HDMI input The -

ANT

antenna input

For best surround sound audio quality from an • external sound system, route audio-carrying cables from the source device directly to your sound system.

IMPORTAN T

Accessory items such as cables, adapters, splitters, or combiners required for TV connections are not supplied with the TV. These items are available at most electronics stores.

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

22 2. TV Connections

Inputs and Outputs

DIGITAL

AUDIO

OUTPUT

(page 27)

CENTER-CH

INPUT

(page 28)

NetC OUT/IR IN

(265 Series) NetCommand/

IR external controller jack. See page 61)

(Ethernet, port

page 42)

LAN

AVR/SURROUND

OUTPUT

(page 27, page 41)

SUBWOOFER OUTPUT

(page 28)

ANT

coaxial antenna input (page 26)

Calibration Microphone Input (265 series, page 40)

AUDIO

analog stereo audio input

Y/VIDEO

posite video input (page 26)

Y/VIDEO Pb Pr

component video input (page 25)

USB USB (Power Only)

Provides power to TV accessories.

(page 28)

DVI/PC AUDIO INPUT

(page 25)

com-

(page 35)

HDMI

(page 24)

AUDIO

analog stereo

audio input

Y/VIDEO Pb Pr

component video input (page 25)

Y/VID E O

composite video (page 26)

HDMI

(page 24)

Cable Routing

Press the release tab to loosen the cable bundle.

Installing the cable tie

Install the supplied cable ties in any of four mounting holes.

Removing the cable tie

Sample cable routing. Secure the cable bundle with the release tab facing out.

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

2. TV Connections 23

Inputs and Outputs, continued

3. Y/

1. ANT (Antenna)

Connect your main antenna or direct cable service (without a cable box) to receive digital and analog over-the-air channels from a VHF/UHF antenna or non-scrambled digital/analog cable source.

2. HDMI® Inputs

ANT

. The

ANT

input can

(High-Definition

Multimedia Interface)

The HDMI inputs support uncompressed standard and

high-definition digital video formats, bitstream Dolby Digital 5.1, and PCM digital stereo audio.

Mitsubishi recommends you use high-speed HDMI cables to connect newer source devices incorporating

HDMI technology. High-speed cables bring you the full benefits of Deep Color and x.v.Color.

These HDMI inputs can also accept digital DVI video

signals. To connect a device’s DVI output to the TV’s HDMI input, use an HDMI-to-DVI adapter or cable plus an analog audio. Connect the audio cable to the

AUDIO INPUT

DVI device.

Use the HDMI inputs to connect to CEA-861 HDMI compliant devices such as a high-definition receiver or DVD player. These inputs support 480i, 480p, 720p, 1080i, and 1080p video formats.

The TV’s HDMI inputs are compatible with many DVI-D

and HDMI computer video signals.

These inputs are HDCP (High-Bandwidth Digital Copy

Protection) compliant.

jack on the TV to receive audio from your

DVI/PC

VIDEO

Use the adjacent send audio to the TV.

4. Y/VIDEO Pb Pr (Component Video)

Use the adjacent send audio to the TV.

5. AUDIO

Analog stereo inputs for use in conjunction with adja-

cent composite or component video jacks.

6. NetC Out/IR IN

265 Series

As an output: Connect IR emitters to this jack to send

NetCommand control signals to external IR-controlled devices.

As an input: Accepts control signals from an external

controller when set up by your professional installer.

7. LAN

Use the to the TV. See page 42 for setup. Visit www.VUDU.com for details about VUDU™ service.

8. USB

The TV can read JPEG photo files and mp3 music files

from a USB storage device connected to this input.

154 Series. Connect a compatible wireless adapter to

stream internet content to the TV

(Composite Video)

AUDIO R

LAN

Ethernet jack for streaming internet video

and L inputs if you wish to

and L jacks if you wish to

(page 42)

HDMI Cable Categories

HDMI cables are available as Standard and High-Speed types.

High-Speed HDMI Cables.• Newer DVD players, video games, and set-top boxes require High-Speed HDMI cables, suitable for clock frequencies up to 340 MHz or data rates of up to 10.2 gigabits per second. Use high-speed cables for 1080p HD signals carrying extended color encodings (i.e., 30 or more bits, also called Deep Color). High-Speed HDMI cables are also suitable for standard HDTV signals.

Standard HDMI Cables• . Standard HDMI cables may be unmarked. They are suitable for standard HDTV 720p, 1080i, and 1080p signals with 8-bit color depth. Use Standard HDMI cables for clock frequencies up to 74.25 MHz or data rates of up to 2.23 gigabits per second.

Downloaded From TV-Manual.com Manuals

9. USB (Power Only)

Standard USB 5-volt, 500-milliamp power output you can use to supply power to an accessory device, such as a wireless subwoofer (page 28).

10. DVI/PC INPUT AUDIO

Connect a DVI device to one of the TV’s HDMI inputs and use this jack to send analog audio to the TV.

11. DIGITAL AUDIO OUTPUT

This output sends Dolby Digital or PCM digital audio to

your digital A/V surround sound receiver. Incoming analog audio is converted by the TV to PCM digital audio. If you have a digital A/V receiver, in most cases this is the only audio connection needed between the TV and your A/V re ceiver.

For assistance call 1(800) 332-2119

24 2. TV Connections

Any HDMI device

HDMI-to-HDMI cable

Inputs and Outputs, continued

12. AVR/SURROUND OUTPUT

Sends analog audio of the current program to an • analog A/V surround sound receiver or stereo system. Digital audio from digital channels and HDMI devices is converted to analog audio by the

TV for output on this jack. This is the only audio

connection needed to the TV if using an analog A/V receiver or stereo system.

Note: If connecting headphones, set Sound > Global > Analog Audio Out to Variable.

For a fuller surround sound effect, connect exter-• nal rear speakers to this output to supplement the

TV’s speaker array. Set Sound > Global > Analog

Audio Out to Rear.

13. SUBWOOFER OUTPUT

Connect a powered subwoofer to this input to complement effects from the TV’s speaker array. Set Sound >

Global > Subwoofer to On to enable this output.

14. CENTER CH INPUT

Connect your A/V receiver’s center channel output to this input to make the TV speakers output center-channel sound. Set Sound > Global > Center Channel to On to enable this input. See Sound > Audio > TV

Speakers > Center page 49.

DMI Device

Commonly used with an HDTV Cable Box, Satellite Receiver, or DVD/Blu-ray Player

Required: HDMI-to-HDMI cable.

Connect an HDMI cable from the TV to the device’s HDMI output. HDMI-connectable devices provide video and audio through a single cable.

Mitsubishi recommends using high-speed HDMI cables to connect newer devices incorporating HDMI technology. See “HDMI Cable Categories” on the previous

page for more on HDMI cable types.

Note: The HDMI connection supports copy protection

(HDCP).

Auto Input Sensing

The TV’s Auto Input Sensing feature automatically recognizes some connections and prompts device type. See page 15.

you to identify the

IMPORTAN T

HDMI and Digital Surround Sound

Use an HDMI connection if you want to hear digital surround sound from the TV’s internal speaker array. The TV’s HDMI inputs can receive digital surround sound from an HDMI device.

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

2. TV Connections 25

AUDIO

Incoming from cable service or satellite dish

Component video device

Audio

cables

Component video cables

CABLE IN or

SATELLITE IN

DVI OUT

AUDIO

OUT

Digital DVI

device

DVI-to-HDMI

cable

Audio cable

Y Pb Pr Component Video Device

Commonly used with an HDTV Cable Box, Satellite Receiver, or DVD/Blu-ray Player

If your source device has an HDMI output, use the connections for HDMI devices described on the opposite page instead of component video.

Required:

RCA-type component video cables Left/right analog audio cables.

Note:

To hear digital surround sound from an A/V receiver, connect the digital audio output from the device directly to your digital A/V receiver.

DVI Video Device

Commonly used with a Cable Box, Satellite Receiver, or DVD Player

Connect a DVI device (digital only) to one of the TV’s HDMI input jacks.

Required:

Analog stereo audio cables DVI-to-HDMI cable or DVI/HDMI adapter and HDMI cable

If you are using a DVI/HDMI adapter, it is important to connect the adapter to the DVI device for best performance.

Some devices require connection to an analog input first in order to view on-screen menus and to select DVI as the ouput. Please review your equipment instructions for DVI connectivity and compatibility.

Note: The HDMI connection supports copy protection

(HDCP).

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

26 2. TV Connections

OUT

Antenna

Not recommeded. Other connection types provide better quality audio and video.

Direct cable (no cable box)

Older cable box

ANT

Cable TV

service

AUDIO OUT

COMPOSITE

VIDEO OUT

Audio cables

VCR or other device with composite video output

Composite video cable

AUDIO OUT

COMPOSITE

VIDEO OUT

COMPONENT

VIDEO OUT

ANTENNA

1a.

1b.

Incoming cable

RF Splitter

DVD Recorder or VCR

Composite

video cable

Antenna or Cable TV Service

Connect the incoming cable to the TV’s

Composite Video Device

ANT

input.

VCR or DVD Recorder to an Antenna or Wall Outlet Cable

Required:

1. Video cables 1a. Component video cables (red/blue/green)

1b. Composite video cable (usually yellow)

2. Left/right analog audio cables.

3. Two-way RF splitter

4. Two coaxial cables

Note:

• Usecompositevideoonlyifcomponent

video or HDMI are unavailable.

• Ifyourrecordingdevicehasananalog-only

tuner, you must use a digital converter box to enable recording of digital broadcasts.

VCR or other device with composite video output

Required:

Composite video cable (usually yellow) Analog stereo audio cables.

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

2. TV Connections 27

COAXIAL

INPUT

OPTICAL

INPUT

OPTICAL

INPUT

Optical cable

(digital A/V

receiver)

Stereo analog cables (analog A/V receiver)

A/V receiver back panel

HDMI cable

HDMI OUT

OPTICAL AUDIO IN

ANALOG AUDIO IN

High-deﬁnition

DVD player

Cable box

VCR

Y/ VIDEO

A/V receiver with

HDMI output

Any connection types

Optional

analog or

digital audio

connection

A/V Receiver

Most setups require either a digital audio cable or analog stereo audio cables. To send audio from TV channels received on the nected directly to the TV, you must use one of the connections shown below.

The TV makes all audio available in digital and analog

formats:

Analog audio coming into the TV is available as • output in digital stereo format on the

AUDIO OUTPUT

Digital incoming audio is available as analog output • on the

AVR/SURROUND OUTPUT L

jack.

ANT

input or devices con-

DIGITAL

and R jacks.

A/V Receiver with HDMI Output

Required: One HDMI-to-HDMI cable

This option allows you to view content from devices connected to an A/V receiver. The A/V receiver can send audio and video to the TV over a single HDMI cable. You can use an HDMI connection as described here in addition to an audio connection from the TV’s audio output. The optional audio connection allows you to hear, through the A/V receiver, devices connected to the TV only, e.g., an antenna on the

You may be able to use the TV’s remote control • (in TV mode) to operate connected CEC-enabled HDMI devices. Experiment with your equipment to determine which functions are available to the TV’s remote control. See Appendix C, page 81.

265 Series:• This setup allows you to use NetCom- mand-controlled audio and video switching over the HDMI cable. See “Automatic Audio/Video Switching Over an HDMI Connection” on page 69.

265 Series:• To use NetCommand to supplement HDMI control of a CEC-enabled A/V receiver, note the recommendations under “More About Using an HDMI Connection,” page 69.

ANT

input.

Note:

On rare occasions, an HDMI signal may be • copy-restricted and cannot be output from the TV as a digital signal. To hear these copyprotected signals through the A/V receiver, use the connection for an analog A/V receiver.

Check the A/V receiver’s Owner’s Guide for • information concerning use of the digital input and switching between digital sound and analog stereo sound from the TV.

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

28 2. TV Connections

Polk Audio PSW i8m powered wireless subwoofer

Power-only

USB port

USB/USB mini-plug power cable

RCA/RCA

audio cable

HDMI cable

HDMI OUT

CENTER

CHANNEL

PRE OUT

Surround sound

source device

A/V receiver

with HDMI

output

RCA/RCA audio cable

Supplemental Audio Connections

Adding a Subwoofer

Add a subwoofer to complement the TV speakers with a fuller bass sound.

After connecting a subwoofer, you must enable the • TV’s subwoofer output in the TV’s Sound menu. Go to

Sound > Global > Subwoofer and set it to On.

To control subwoofer volume, press the • and then press to find the subwoofer volume slider. Press to change the volume.

Subwoofer with Audio Cable

Connect the subwoofer directly to the TV’s

OUTPUT

AUDIO

key

SUBWOOFER

Using the TV Speakers as a Center Channel

If using an external surround sound system, you can make the TV’s speakers provide center channel sound. Your A/V receiver must have a center channel pre out that can supply an amplified center-channel signal to the TV.

Connect your A/V receiver’s HDMI output and center

channel pre out to the TV as shown.

Wireless Subwoofer

Mitsubishi recommends Polk Audio Wireless Subwoofer model PSW i8m. The transmitter module can be conveniently powered from the TV’s USB power port. Connect an audio cable to the transmitter to supply audio from the TV’s

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

SUBWOOFER OUTPUT

Turn on the A/V receiver’s center channel pre out if

needed. See the A/V receiver’s instruction manual. Press the

Enable the TV’s center channel mode:

a. Go to Sound > Global and set Center Channel

b. Press the

To balance volume:

a. Power on the A/V receiver and TV. b. Compare the volume of the TV’s center channel

VOL key to adjust TV volume to about level 30.

to On.

AUDIO

key and press to display the

TV Speakers option. Press to select Center.

with the rest of the sound system. If the TV volume needs adjustment, i. Turn on the TV speakers. Press

press to display the TV Speakers option. Press to select

ii.

Adjust TV volume using

iii. Return the TV to center channel mode. Press

AUDIO

and press to display the TV Speak-

ers option. Press to select Center.

iv. Compare the sound volume. Repeat this

adjustment if needed.

On.

the

AUDIO and

VOL key.

TV Features

Sleep Timer

The Sleep Timer turns the TV off after the length of time you set. To set the TV to turn on at a certain time of day, see the Setup > Timer menu on page 52.

Setting the Sleep Timer

Press

Viewing or Changing the Sleep Timer

SLEEP

Press

SLEEP

additional times to increase the time in 30-minute increments up to the maximum of 120 minutes.

Press

EXIT

to clear the screen immediately erwise the screen will clear after five seconds of inactivity.

Press

SLEEP

to display the on-screen message.

Press

SLEEP

additional times to change the time before the TV powers off. To cancel the Sleep Timer, press played.

SLEEP

repeatedly until OFF is dis-

Oth-

FAV (Favorite Channels)

The

FAV

key gives you quick access to favorite program sources. Sources can be channels from the or devices connected to the TV. You can store up to nine favorites.

Sample Favorites menu. Switch to favorite channels or inputs using number keys.

Press 1.

INPUT

and switch the TV to the input you want to add. If adding a channel, switch to the

ANT

input and tune to the channel.

Adding

Press the 2. Move the highlight to the number position 3.

you want to assign to the channel or input. Press 4.

FAV

ENTER

key.

ANT

input

Downloaded From TV-Manual.com Manuals

Removing

Selecting

While watching TV, press the 1. In the 2. Favorites menu, highlight the channel

or input you want to remove. Press 3.

CANCEL

While watching TV, press the 1. Move the highlight to the item you want and 2.

press

ENTER

number key for the channel or input.

. For a shortcut, just press the

FAV

key.

For assistance call 1(800) 332-2119

30 3. TV Features

ChannelView Channel Listings

ChannelView displays program descriptions sent by broadcasters. This information may be unavailable in some areas.

About ChannelView

ChannelView™ shows memorized channels on the ANT input. It displays channel names and program information for digital channels. No program information is displayed for analog channels.

ChannelView allows you to set up three banks of custom channels for convenient access. You can save groups of channels by content (e.g., news, sports, children’s programming) or by TV user.

Note: You must ﬁrst set the TV Clock (page 52) to

receive ChannelView listings.

ChannelView, “All” tab. Programs are listed on the right.

Using ChannelView Listings

Task Action

Display/hide ChannelView listings (ANT input only).

Move through channels one by one.

Move through channels quickly.

Jump to listings for a specific channel.

Tune to a highlighted channel.

Update program information for a highlighted digital channel.

Display program descriptions, if available. The description will appear at the bottom of the screen.

Display more program description for the current channel (if available).

Press

GUIDE.

Press or .

Press

CH.

Enter the channel number. Press

CANCEL

press twice to clear the channel number.

Press

ENTER.

Press the screen may briefly go blank).

Press 1. to move into the program area. Press 2. to move between programs.

Press

INFO.

to add a dash;

INFO

key (the

ChannelView Custom Channel Banks

Select a channel bank to customize.

Press

Task Action

Move between banks

Move into the channel list

Add or delete a channel from the bank

Remove all channels from the selected bank

Enter or exit setup mode Press

GUIDE

to display ChannelView.

Press

to move the highlight to the bank

header. Press With the bank name highlighted, press

enter setup mode where you can select channels to include in the bank.

Press

to select Bank 1, 2, or 3.

EXIT

when finished with setup.

Press . Press .

Highlight the channel • and press check indicates the channel has been added. Press • clear the check and remove the channel.

Press

ENTER

CANCEL.

MENU.

ENTER

again to

Using Custom Channel Banks

While watching TV, press • to channels stored in the current bank.

To • change to a different channel bank:

Press 1.

GUIDE.

Press 2.

MENU.

Press 3. . Press 4.

EXIT.

To allow tuning to any channel in memory, select • the All bank.

. The TV will tune only

. A

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

+ 74 hidden pages