Mitsubishi Electric EY-3D-EMT2H User Manual
Contents
ENGLISH
Mitsubishi projectors compatible with this 3D emitter
(as of June 2012)
HC7900DW
Supported projectors are subject to change without notice.
For details about the 3D system, see the descriptions of the 3D in the User Manual
supplied with the projector.
Safety precautions ......................2
Using precautions .......................2
Introduction .................................5
What’s included in the box ..........5
Installation and connection .........5
Troubleshooting ...........................7
Specifi cations ..............................7
This User Manual is important to you.
Please read it before using your 3D emitter.
3D EMITTER
MODEL
EY-3D-EMT2H
User Manual
EN-2
Safety precautions
WARNING:
Do not store screws in places where small children can reach.
There is a danger small children could swallow such parts by mistake. If a child
accidentally swallows such parts, seek immediate medical attention.
Contact your dealer if there is something wrong with your 3D emitter.
Do not operate if smoke, strange noise or odor comes out of your projector. It
might cause fi re or electric shock. In this case, contact your dealer immediately.
Do not keep using the damaged 3D emitter.
It can lead to fi re or electric shock.
Do not drop or modify your 3D emitter.
It can lead to breakdown or other failure.
CAUTION:
Not for use in a computer room as defi ned in the Standard for the Protection of
Electronic Computer/Data Processing Equipment, ANSI/NFPA 75.
This 3D emitter is used only for Mitsubishi projectors supporting 3D
images.
Use this 3D emitter only for viewing 3D images on the supported Mitsubishi
projectors.
The 3D glasses work by receiving an infra-red light from the 3D emitter. Other
infra-red communication devices, lighting fi xtures, or heating appliances placed
near the 3D emitter may affect the operation of the 3D glasses.
View 3D images within the signal reception range.
The signal of the 3D emitter may be affected by that of the infra-red remote
control. In such a case, change the orientation of the 3D emitter.
A remote control may operate improperly while you watch the 3D images,
however, it is not a malfunction.
When using the device in Europe:
COMPLIANCE NOTICE
This device complies with the requirements of the EC Directive 2004/108/EC
“EMC Directive” .
The electro-magnetic susceptibility has been chosen at a level that gains proper
operation in residential areas, on business and light industrial premises and on
small-scale enterprises, inside as well as outside of the buildings.
Using precautions
EN-3
ENGLISH
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced Radio/TV technician for help.
Any changes or modifi cations not expressly approved by Mitsubishi could
void the user’s authority to operate this equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class B digital apparatus complies with Canadian ICES-003.
Declaration of Conformity
Model number: EY-3D-EMT2H
Trade name: MITSUBISHI ELECTRIC
Responsible party: Mitsubishi Digital Electronics America, Inc.
9351 Jeronimo Road, Irvine, CA 92618 U.S.A
Telephone number: +1-(949) 465-6000
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Loading...