Mitsubishi AA192AA51 Specification

Global LCD Panel Exchange Center

u

www.panelook.com

TENTATIVE

All information in this technical data sheet is tentative

and subject to change without notice.

19.2” 1920

360

TECHNICAL SPECIFICATION

AA192AA51

MITSUBISHI ELECTRIC Corp.

Date: Feb.8,’12

MITSUBISHI

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

(1/25) AA192AA51_02_00

www.panelook.com

Global LCD Panel Exchange Center

CONTENTS



No. Item Page

-- COVER 1

-- CONTENTS 2

1 APPLICATION 3

2 OVERVIEW 4

3 ABSOLUTE MAXIMUM RATINGS 5

4 ELECTRICAL CHARACTERISTICS 5, 6, 7

www.panelook.com

5 INTERFACE PIN CONNECTION 8, 9

6 INTERFACE TIMING 10, 11, 12, 13, 14

7 BLOCK DIAGRAM 15

8 MECHANICAL SPECIFICATION 16, 17

9 OPTICAL CHARACTERISTICS 18, 19, 20

10 RELIABILITY TEST CONDITION 21

11 OTHER FEATURE 22

12 HANDLING PRECAUTIONS FOR TFT-LCD MODULE 23, 24, 25

MITSUBISHI

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

(2/25) AA192AA51_02_00

www.panelook.com

Global LCD Panel Exchange Center



1. APPLICATION

This specification applies to color TFT-LCD module, AA192AA51.

These specification papers are the proprietary product of Mitsubishi Electric Corporation

(“MITSUBISHI) and include materials protected under copyright of MITSUBISHI. No part of this
document may be reproduced in any form or by any means without the express written permission
of MITSUBISHI.

MITSUBISHI does not assume any liability for infringement of patents, copyrights or other

intellectual property rights of third parties by or arising from use of a product specified in this
document. No license, express, implied or otherwise, is granted under any patents, copyrights or
other intellectual property rights of MITSUBISHI or of others.

MITSUBISHI classifies the usage of the TFT-LCD module as follows. Please confirm the usage

before using the product.

(1) Standard Usage

Computers, office equipment, factory automation equipment, test and measurement
equipment, communications, transportation equipment(automobiles, ships, trains, etc.),
provided, however, that operation is not influenced by TFT-LCD directly.

(2) Special Usage

Medical equipment, safety equipment, transportation equipment, provided, however, that
TFT-LCD is necessary to its operation.

(3) Specific Usage

Cockpit Equipment, military systems, aerospace equipment, nuclear reactor control
systems, life support systems and any other equipment. MITSUBISHI should make a
contract that stipulate apportionment of responsibilities between MITSUBISHI and our
customer.

The product specified in this document is designed for “Standard Usage” unless otherwise specified

in this document. If customers intend to use the product for applications other than those specified
for “Standard Usage”, they should first contact MITSUBISHI sales representative for it's intended
use in writing.

MITSUBISHI has been making continuous effort to improve the reliability of its products.
Customers should implement sufficient reliability design of their application equipments such as
redundant system design, fail-safe functions, anti-failure features.

MITSUBISHI assumes no responsibility for any damage resulting from the use of the product that

does not comply with the instructions and the precautions specified in this document.

Please contact and consult a MITSUBISHI sales representative for any questions regarding this

product.

www.panelook.com

MITSUBISHI

(3/25) AA192AA51_02_00

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

2. OVERVIEW

AA192AA51 is 19.2” color TFT-LCD (Thin Film Transistor Liquid Crystal Display) module
composed of LCD panel, driver ICs, control circuit, LED driver and backlight unit.

By applying 6 bit or 8 bit digital data, 1920u 360, 262k-color or 16.7M-color images are displayed
on the 19.2” diagonal screen. Input power voltages are 3.3 V for LCD driving and 12 V for
backlight unit.
The type of data and control signals are digital and transmitted via LVDS interface per Typ. 60
MHz clock cycle.
This product has LED driving circuit inside. The LED driving circuit has DC light dimming
function, which is controlled by DC voltage or resistance.

General specifications are summarized in the following table:

ITEM SPECIFICATION

Display Area (mm)

Number of Dots

www.panelook.com

478.08(H) u 89.64(V)
(19.2-inch diagonal)

1920 u3 (H) u 360 (V)

Pixel Pitch (mm)

Color Pixel Arrangement RGB vertical stripe

Display Mode Normally white

Number of Color 262k(6 bit/color), 16.7M(8 bit/color)

Luminance (cd/m2) 650

Viewing Angle (CR t10) 60~80° (H), 80~80° (V)

Surface Treatment Anti-glare and hard-coating 3H

Electrical Interface LVDS (6 bit/8 bit)

Viewing Direction

Module Size (mm)

Module Mass (g) 780

Backlight Unit LED, edge-light, Unreplaceable

Characteristic value without any note is typical value.

Less gray scale reversal: 3 o'clock

0.249 (H) u 0.249 (V)

Higher Contrast ratio: 9 o'clock

496.0 (W) u 109.2 (H) u 13.9 (D)

MITSUBISHI

(4/25) AA192AA51_02_00

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

3. ABSOLUTE MAXIMUM RATINGS

ITEM SYMBOL MIN. MAX. UNIT

www.panelook.com

Power Supply Voltage for LCD VCC

Logic Input Voltage VI

Backlight Power Supply Input Voltage VL

Backlight ON-OFF BLEN

Light Dimming Control Input Voltage VBRT

Operation Temperature (Panel)

Operation Temperature (Ambient)

Storage Temperature

Note 1,2)

T

Note 2)

T

Note 2)

T

op(Ambient)

op(Panel)

stg

0.3

0.3

0.3

0.3

0.3

30

30

30

4.0 V

VCC+0.3 V

14.0 V

VL V

3.0 V

80 °C

80 °C

80 °C

[Note]

1) Measured at the center of active area and at the center of panel back surface

2) Top,Tstgd 40qC : 90%RH max. without condensation
Top,Tstg > 40qC : Absolute humidity shall be less than the value of 90%RH at 40qC without

condensation.

4. ELECTRICAL CHARACTERISTICS

(1) TFT- LCD Ambient temperature: Ta = 25°C

ITEM SYMBOL MIN. TYP. MAX. UNIT Remarks

Power Supply Voltage for LCD VCC 3.0 3.3 3.6 V *1)

Power Supply Current for LCD ICC -- 560 800 mA *2)

Permissive Input Ripple Voltage VRP -- -- 100 mVp-p VCC=+3.3V

High VIH

0.8uVCC

-- VCC V MODE, SC

Logic Input Voltage

Low VIL 0 --

0.2uVCC

V MODE, SC

*1) Power and signals sequence:

0.1 ms d t1 d10ms 200 ms dt4
0 < t2 d 50 ms 200 ms dt5

0 < t3 d 50 ms 0 dt6

LCD Power Supply

Logic Signal

Backlight Power Supply

0.9VCC

0.1VCC

t1

t2

VCC

data

t3

0.9VCC

0.1VCC

t4

0.1VCC

t5 t6

data: RGB DATA, DCLK, DENA, MODE, SC

MITSUBISHI

(5/25) AA192AA51_02_00

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

VCC-dip conditions:

www.panelook.com

1) When 2.6 V

d VCC < 3.0 V, td d 10 ms

2) When VCC < 2.6 V

VCC-dip conditions should also follow the power and signals sequence.

VCC

3.0 V

2.6 V

td

*2) VCC = + 3.3 V, f

=23.4kHz, fV=60Hz, f

H

= 60MHz

CLK

Display image at typical power supply current value is 256-gray-bar pattern (8 bit), 360 line

mode.

*3) Fuse

Parameter Fuse Type Name Supplier Remark

VCC FCC16202AB Kamaya Electric Co., Ltd. *)

*) The power supply capacity should be designed to be more than the fusing current.

(2) Backlight Ta=25°C

ITEM SYMBOL MIN. TYP. MAX. UNIT Remarks

Power Supply Input Voltage VL 10.8 12.0 13.2 V *1)

Power Supply Input Current IL -- 1.2 1.8 A

Power Supply Input Current
(Rush Current)

ILR -- -- (3) A *2), VL=12.0V

Dimming=100%,

VL=12.0V

High 2.5 -- VL V *1), ON

Backlight ON-OFF

Low

Light Dimming Control Input

Voltage / Resistance

BLEN

0 -- 0.4 V *1), OFF

VBRT 0 -- 2.5 V

RBRT 0 -- 50

k㱅 *4),0k㱅: Max. Luminance

*1), *3)

0V: Max. Luminance

LED Life Time LT 80,000 100,000 -- h *5), *6)

MITSUBISHI

(6/25) AA192AA51_02_00

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

V

*1) Power and signals sequence:

t1

www.panelook.com

L

BLEN

0.9VL

0.1VL

t3

0.1VL

t2

0.1VL

0.1  t1  100 ms
200  t2 ms
200  t3 ms

The sequence of VBRT is not matter.
Order of VL and BLEN on Power-on/off sequence is not matter.

*2) These data are for reference only. Power Supply Input Current (Rush Current) is influenced

by power supply characteristics.(output impedance in particular) Therefore please evaluate LCD
in advance.

*3) If there is ripple noise on Light Dimming Control Voltage (VBRT), flicker may be visible. Please

evaluate it in advance.

*4) RBRT need to be connected to GND via resistor (0a50 k:).

*5) LED life time is defined as the time when the brightness becomes 50% of the initial value.

*6) The life time of the backlight depends on the ambient temperature. The life time will decrease

under high temperature.

*7) Fuse

Parameter Fuse Type Name Supplier Remark

VL FHC16322AD Kamaya Electric Co., Ltd.

*)

*) The power supply capacity should be designed to be more than the fusing current.

MITSUBISHI

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

(7/25) AA192AA51_02_00

www.panelook.com

Global LCD Panel Exchange Center

V

5. INTERFACE PIN CONNECTION

(1) CN 1(Interface Signal)

Used Connector: DF14A-20P-1.25H(56) (HIROSE)
Corresponding connector: DF14-20S-1.25C (HIROSE)

Pin

No.

Symbol

1 VCC
2 VCC
3 GND
4 GND
5

Link 0

R0, R1, R2, R3, R4, R5, G0 R2, R3, R4, R5, R6, R7, G2
6 Link 0+ R0, R1, R2, R3, R4, R5, G0 R2, R3, R4, R5, R6, R7, G2 R0, R1, R2, R3, R4, R5, G0
7 GND
8

Link 1

G1, G2, G3, G4, G5, B0, B1 G3, G4, G5, G6, G7, B2, B3
9 Link 1+ G1, G2, G3, G4, G5, B0, B1 G3, G4, G5, G6, G7, B2, B3 G1, G2, G3, G4, G5, B0, B1

10 GND
11

Link 2

B2, B3, B4, B5, DENA B4, B5, B6, B7, DENA

12 Link 2+ B2, B3, B4, B5, DENA B4, B5, B6, B7, DENA B2, B3, B4, B5, DENA
13 GND
14

CLKIN Clock  m
15 CLKIN+
16 GND
17

Link3

See: *2) R0, R1, G0, G1, B0, B1

18 Link3+ See: *2) R0, R1, G0, G1, B0, B1 R6, R7, G6, G7, B6, B7

19 MODE Low=ISP 6 bit compatibility mode

20 SC

Scan direction control ( Low = Normal , High = Reverse )

*1) Metal frame is connected to signal GND.
*2) Recommended wiring of Pin 17,18 (6 bit input)

Function(ISP 6 bit compatibility mode)

6 bit input 8 bit input

+3.3 V Power supply
+3.3 V Power supply

www.panelook.com

GND
GND

GND

GND

GND

Clock +

GND

Function(ISP 8 bit

compatibility mode)

m
m
m
m

R0, R1, R2, R3, R4, R5, G0

m

G1, G2, G3, G4, G5, B0, B1

m

B2, B3, B4, B5, DENA

m

m
m

R6, R7, G6, G7, B6, B7

High=ISP
8 bit compatibility mode

m

(2) CN 2(Backlight)

Backlight-side connector: SM14B-SRSS-TB(LF)(SN) (JST)
Corresponding connector: SHR-14V-S-B (JST)

Pin No. Symbol Function

1, 2, 3, 4, 5 VL Power Supply Input Voltage

6, 7, 8, 9, 10 GND GND

11 BLEN

12 VBRT / RBRT

13, 14 GND GND

LVD S
transmitter

LOW data

CC

680

Ω

Pin 17
Pin 18

or

620

Ω

Pin 17

Pin 18

Backlight ON-OFF

OFF: 0

a0.4(V) or OPEN / ON: 2.5aVL(V)

PWM Dimming MIN. Brightness: 2.5(V) or 50(k

PWM Dimming MAX. Brightness: 0(V) or 0(k

:)

:)

MITSUBISHI

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

(8/25) AA192AA51_02_00

www.panelook.com