Mission MS-CUBE, MS-8, MS-DUO, MS-10 User Manual

Ms subwoofer_A3.pdf 2008-10-14 15:13:45

Cautions: Before installing this product read all these instructions.

Warning

IMPORTANT SAFETY INSTRUCTIONS

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

DO NOT use this apparatus near water.

Clean only with dry cloth.

DO NOT install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

Unplug this apparatus during lightning storms or when unused for long periods of time.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Install in accordance with the manufacturer’s instructions.

WARNING: If using spikes make sure that they do not pierce mains cable etc. under /above the carpet.

When making any connections, switch the amplifier off.

When you switch on your system or change sources, set the volume control at minimum and turn the level up gradually.

DO NOT use your amplifier at full volume.

Avoid extreme settings of tone controls or graphic equalisers. Ideally, they should be set ‘flat’ or, if possible, bypassed.

DO NOT place heavy objects on top of loudspeaker cabinets.

Ensure that all loudspeakers in the system are correctly wired and are in phase.

DO NOT connect your loudspeakers to the mains supply, except for subwoofers.

DO NOT attempt to dismantle the loudspeaker. There are no user serviceable

parts inside and you will render the warranty void.

Site hi-fi electronics away from the loudspeakers on a rigid stand or cabinet.

Loudspeakers should not be placed directly facing other hi-fi units, or share the same shelf or cabinet.

Site unscreened speakers and subwoofers at least 0.5m away from TV sets, computers etc. Some manufacturers forbid the placing of objects on top of their TV sets. Check your TV handbook before installing the centre speaker directly on your TV set. Consult your TV dealer if you are in any doubt.

Use only attachments / accessories specified by the manufacturer.

DO NOT subject loudspeakers to excessive cold, heat, humidity or sunlight.

DO NOT block any ventilation openings.

DO NOT defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

The apparatus must not be exposed to dripping or splashing and no objects filled with liquids, such as vases, should be placed on the apparatus.

Use only with a cart, stand, tripod, bracket or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart / apparatus combination to avoid injury from tip-over.

CAUTION SUBWOOFER:

located on the rear panel. To permit free access to this switch the apparatus must be located in an open area without any obstructions. The mains power plug must remain freely operable at all times.

CAUTION:

manufacturer could void the user’s authority to operate this device.

I The subwoofer is supplied with a plug

MPORTANT NOTICE TO UK USERS.

incorporating a fuse, the value of which is indicated on the pin face of the plug. If the fuse or plug needs to be replaced refer to the instructions on Page 11.

Mv-as

Changes or modifications not expressly approved by the

The mains power switch for this appliance is

CAUTION!

RISK OF ELECTRIC SHOCK

DO NOT OPEN

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-REMOVEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED PERSONNEL

ADVERTISSEMENT: RISQUE DE CHOC ELECTRIQUE-

NE PAS OUVRIR

When an amplifier is driven beyond its power output capabilities it will produce distorted results which will quickly damage your speakers by overheating. Make sure that your amplifier is not left unattended when playing, for example at parties, and turn the volume control down at the first sign of audible distortion.

Warranty Conditions

The warranty card enclosed should be completed and returned to Mission or its Distributor within 8 days of purchase.

No Dealer or Distributor may vary the terms of this warranty which is personal to the original purchaser and is not transferable.

Please retain the sales receipt as proof of purchase.

Warranty claims must wherever possible be made through the Dealer from whom the equipment was purchased.

This warranty excludes:

Damage caused through neglect, accident, misuse, wear and tear, or through incorrect installation, adjustment or repair by unauthorised

personnel. Any unauthorised servicing will result in loss of warranty.

Liability for damage or loss occurring in transit to or from the purchaser.

Consequent damage, loss or injury, arising from or in conjunction with this equipment.

Equipment for attention under warranty should be considered return carriage paid. If equipment is found to comply with the published specification, Mission reserves the right to raise a charge.

The above conditions do not affect your statutory rights as a consumer.

Specifications

Recommended Amplifier:

MS-8 MS-10

Integrated 100W amplifier

Integrated 150W Integrated 200W Integrated 150W amplifier amplifier amplifier

MS-CUBE MS-DUO

Welcome to Mission

The series is the latest in a long line of distinguished Mission loudspeakers. These technologically advanced loudspeakers will

complement the finest electronics and décor. ass drivers tweeters are used throughout the range.

Screw fastening tri-lobe multi-way

binding posts feature on all models. Your Mission loudspeakers will bring you great listening

pleasure for many years.

Robust b and precision silk

Enclosure:

Effective Volume:

Frequency Response

Filter Selection

Bass Unit

Net Weight

Dimensions

Height on Feet

Electrical Class

Mission reserves the right to change all specifications without notice.E&OE

(HxWxD):mm 300x 300 x330 410x280x500 38 345 37 38 330 355

mm 330 410 38

reflex

20 litres 35 litres

: 38 Hz - 120 Hz

35Hz-85Hz 40Hz - 200Hz (10 Hz steps) (variable)

250mm

11.0 kg

Class II Class I1 Class I Class I Do not Earth. Requires Earth Requires Earth Requires Earth

reflex reflex reflex

30 Hz - 165 Hz 35 Hz - 110 Hz 35 Hz - 110 Hz

250mm 250mm 250mm

18.6 kg 15.0 kg 15.2 kg

Note for UK Customers

The power cord on your subwoofer may be supplied with a plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA or BSI approved BS1362 fuse must be used of the same rating. If the plug is cut off it must NOT be re-used. Dispose of any such plug safely. There is a danger of electric shock if a cut-off plug is inserted into a mains socket.

The wires in the mains lead are coloured in accordance with the following code: Green and Yellow - Earth: Blue - Neutral: Brown - Live. As the colours of the wires in the mains lead may not correspond with the

markings identifying the terminals in the replacement mains plug, proceed as follows:

MS-DUO; MS-10: MS-CUBE:

The wire coloured Blue must be connected to the terminal marked with the letter ‘N’ or coloured Black. The wire coloured Brown must be connected to the terminal marked with the letter ‘L’ or coloured Red. The wire coloured Green and Yellow must be connected to the terminal marked with the letter ‘E’,or coloured Green, or Green and Yellow, or marked with the Earth symbol

MS-8:

EARTH (GREEN/YELLOW)

NEUTRAL

(BLUE)

NEUTRAL

(BLUE)

(BROWN)

FUSE

LIVE

FUSE

LIVE

30 litres 30 litres

35Hz-85Hz 35Hz-85Hz (10 Hz steps) (10 Hz steps)

0x x 0 0x x

0 380

General Information

Please read these instructions carefully before installing your loudspeakers. A few minutes studying this manual will ensure superb performance from your loudspeaker for many years.

Please pay attention to all cautions printed on the pages marked with this symbol.

Unpacking Your Loudspeakers

•

Carefully unpack each loudspeaker.

•

Retain all the packing materials so that your loudspeaker can be repacked and shipped without damage.

•

If you dispose of the packing,do so with regard to all recycling provisions in your area..

Fitting Spikes

Warning: Be careful. Loudspeaker spikes are very sharp.

When positioning the speakers avoid piercing any electrical cables.

• Mv-6 Mv-8

The and loudspeakers are supplied with the spike retainers fitted to the plinth but you will need to fit the spikes

Fitting the Spikes

•

Invert the loudspeaker and place the top on a soft stable surface, or place the loudspeakers on a towel or soft cloth to protect the surface.

•

Screw a nut fully on to each spike but ensure the nut is not tight.

•

Place a washer over the spike retainer.

•

Screw a spike half way into each spike retainer fitted in the base of the cabinet.

•

Tighten the nut finger tight onto the spike retainer.

•

Carefully return the loudspeaker to its normal position.

•

Ensure that spikes do not pierce cables etc. under the carpet.

Adjusting the Spikes

•

Loosen each collar slightly.

•

Adjust the height by screwing in or out one or more of the spikes until the loudspeaker is stable and level.

•

Tighten the nut fully tight onto the spike retainer.

Warning:

The and loudspeakers are heavy.

Mv-6 Mv-8

Always get someone to help you to lift and manoeuvre the loudspeakers.

Never drag a loudspeaker. W lift them clear of the floor and replace them carefully

hen moving loudspeakers

The Mission Powered SubwooferMS-DUO

INPUT

OUTPUT

VOLUME

LEFT

RIGHT

POWER

AUTO

PHASE

Serial Number

180°

ON0°OFF

WARNING:

TO REDUCE

THE

RISK

FIRE

OR ELECTRICAL

SHOCK,

DO NOT EXPOSE

THIS

PRODUCT TO

RAIN

OR MOISTURE

CAUTION: ATTENTION:

OFF ON

REPLACER

FUSIBLE.

UTILISER UNFUSIBLE

RECHANGE

DE MEMETYPE

CALIBRE

DISCONNECT

SUPPLY

CORD

BEFORE CHANGING

FUSE.

REPLACE ONLY

WITH

SAME

TYPE

FUSE

AND

RATING

35Hz

45Hz

55Hz

65Hz

75Hz

85Hz

AC220-240V 50Hz 150W

FUSE T3.15AL250V

CROSSOVER FREQUENCY

0 10

Power Inlet

Power

SPEAKER

LEVEL

INPUTS

Troubleshooting

b c

d e

i j

LINE LEVEL

Serial Number

Power Inle t

MS-DUO

Active Subwoofer

SHOCK,

N21090

Before investigating a problem, always switch off the system at the mains.

If your systemis notworking properlyplease workthrough thischecklist beforereturning aunit toyour dealer.

Symptom Possible Cause

No Sound

Sound lacks bass content Bass reproduction indistinct

Excessive bass distortion at low volumes

Excessive or distorted bass at high levels

Distorted / rattling sounds at high levels

Popping or thumping from the subwoofer

Television picture colour is distorted

System not switched on; Speaker cables shorting terminals out; Wrong source selected

Subwoofer not switched on; Subwoofer phase incorrect; Subwoofer crossover control too low

Subwoofer level set too high; LFE level set too high; Subwoofer incorrectly wired

System level set too high; Bass control set too high; Subwoofer too close to room corners

System level too high; Objects on subwoofer; Objects too close to subwoofer

System level set high; Subwoofer level set too high; LFE level set too high

Subwoofer too close to TV. (Switch off system and TV. Move units away. Leave 15 mins. Switch on.

Loudspeaker Maintenance

Subwoofers should onlyever becleaned witha softdry clothto removefingermarks etc..

Never touch subwooferdrive unitsas theycan bedamaged byimproper handling.

NUMERICAL KEY

Phase Control

Line Level Outputs

Line Level Inputs

Volume Control

Speaker Level Inputs

FUSE T3.15AL250V

AC220-240V 50Hz 150W

FUSE.

FUSIBLE.

Crossover Frequency Control

Auto Power Switch

Mains Power Indicator

Mains ON/OFF Switch

IEC Mains Input Socket

Mains Power Fuse

Preliminaries Power Connections

Open the carton and remove all the top packing pieces. Lift the subwoofer out carefully. DO NOT lift the subwoofer out of the carton using the protective bag. The unit is heavy; if you cannot

manage it easily, get assistance.

Retain the packing materials. If you decide not to keep the packing, please dispose of it having regard to any recycling regulations in your area. Please retain the user manual. If you transfer this equipment to a third party, please ensure all the instructions are passed on with the product.

The subwoofer is factory set to operate from the mains voltage marked on the amplifier panel. Before connecting check this voltage is correct for your mains supply.

230 volt products - 220 V to 240 V

115 volt products - 110 Vs to 120 V

If you move to an area with a different mains supply, consult your dealer for advice.

Never use avacuum cleanerto cleana subwoofergrille. Brushit carefullyby handwith asoft brush.

When cleaning the floor under a subwoofer; switch it off, unplug it from the mains supply then lift it clear of the floor and move it to another location. Replacethe subwooferafter cleaning.

Product Service

Should a faultoccur withyour subwoofer,please packit correctly,using theoriginal packing,so youcan shipit safely..

Product for service should be returned to the appointed dealer from whom you purchased the product. If you experience difficulties or there is noMission dealerin yourarea, contactthe Missiondistributor foryour country or theMain Service Centre foryour region.

Authorised Service Centres

International Audio Group IUnit 4, StMargaret’s Way, Stukeley Meadows IndustrialEstate Huntingdon, Cambs, PE29 6EB Tel:+44 (0)1480 447700 Fax: +44 (0)1480 431767

ASIA

IAG. Room 2310 - 2311, Press Building, Shennan Road C, Shenzhen, China. Tel: +86-755-82091200 Fax: +86-755-82091205

10 13

Stereo Reproduction

The subwoofer is supplied in front-firing mode.

Changing the Operating Mode from Front-Firing to Down-FiringMS-DUO

Low Pass Filter:

The subwoofer crossover point should be set having regard to the size and low frequency extension of the main speakers. The role of the subwoofer is to extend the bass response of the system, not to increase the overall bass level. If the loudspeakers are large the crossover should be set low,a value around 55 Hz is a good place to start. With smaller speakers this can be increased, up to 85Hz for the small bookshelfunits. Asalways thefinal valueis determinedby listening.

Low-level Listening

Our ears are far more sensitive to midrange frequencies (2-5 kHz) than bass frequencies. Very low bass and especially percussive bass is‘felt’ rather than heard. At low sound levels bass frequenciesappear to attenuate faster than midrange andtreble. As the level increases this bass roll-off decreases. Occasionally we may wish to listen to a normally loud piece of music at a low level but with retention of thebass information.

Testing the system

The simplest way to test the system is to play, at a moderate level, music with deep consistent bass. Switching the subwoofer on and off should cause change of the depth of bass, and the ambience will also alter. If there is a significant change in bass volume, or a noticeable step in the bass response, or an increase in coloration when the subwoofer is playing, the setup needs to be refined. By selecting different crossoverand volumesettings, youwill beable readilyto identifythe mostfavourable combination.

Dolby Labs Recommended 7.1 Placement

Left Front

Centre

LFE

22º

30º

Right Front

The MS-DUO

You c an (amplifier beneath the subwoofer)

To change the mode from down firing to front firing:

Remove the grille from the front of the loudspeaker Place a towel or similar on the ground.

Screw the cone feet tightly into the holes that held the pegs Stand the subwoofer on its feet as shown in the illustration

subwoofer is supplied in front-firing mode.

operate the subwoofer with the drive unit firing downwards (amplifier at the rear) or firing forwards

Invert the subwoofer and place it carefully on the towel. Remove the four cone feet from the subwoofer

Front Firing Mode

Unscrew the four pegs that held the grille in place

Left Surround

Left Back

150º

(Single Back channel for 6.1

90º

110º

135º

Right Back

Right Surround

Down Firing Mode

In down firing mode the grille must be removed Store the grille and the pegs safely for future re-use.

Reverse the procedure to change the mode.

Which mode should I use?

You should experiment with different operating modes to see which one you prefer. Here are some notes which may help you.

Front firing mode keeps the drive unit away from walls and offers a better focussed sound with lowest bess distortion.

If your floor is a hard wood or stone floor, front-firing will offer advantages especially if you are using a suspended wood floor.

In front firing mode the amplifier faces downwards so there are some potential disadvantages:

If you have a deep shag pile carpet, there may be insufficient ventilation for the amplifier and we do not advise you to use this mode of operation.

Although the Subwoofer controls are designed to be “set and forget”, if you are likely to adjust the controls often, down firing mode is easier for day to day use.

The Mission Powered SubwooferMS-10

35Hz

45Hz

55Hz

65Hz

75Hz

85Hz

CROSSOVER

FREQUENCY

35Hz

45Hz

55Hz

65Hz

75Hz

85Hz

CROSSOVER

FREQUENCY

NUMERICAL KEY

Crossover Frequency Control

Mains/Standby

Volume Control

Phase Switch

LEFT Line Input

RIGHT/LFE Input

Speaker Level Inputs

Mains Voltage Selector

Mains ON/OFF Switch

IEC Mains Input Socket

Mains Power Fuse

Indicator

Setting Up your Subwoofer - All Models

Set the subwoofer power switch to OFF.

Turn the system Volume Control to minimum.

Re-check all system connections.

Connect the supplied power lead to the IEC power socket on the subwoofer and connect the mains plug into the wall socket.

Set the subwoofer volume control midway (12 o'clock)

Switch on the mains power.

Fine Tuning Your Subwoofer

Switch on the subwoofer power switch. Check that the power indicator on the amplifier panel glows. Now switch on the system. Play a programme with extended bass and set the system volume to a reasonable level. Adjust the subwoofer volume control to produce the desired level of bass.

PHASE SWITCH:

carefully to some music with extended bass. If there is insufficient bass output from the sub-woofer set the Phase switch to 180º. Select the position which produces the most natural, extended bass.

LOW PASS (CROSSOVER) FILTER:

system to be set up for optimum bass performance. The higher settings are for use with bookshelf loudspeakers, the lower settings for large floorstanding models. If you choose too low a setting with small speakers, there will be a ‘hole’ in the bass response; too high a setting with large speakers will result in the upper bass becoming bloated.

AUTOPOWER SWITCH- MS-CUBE; MS-8; MS-DUO

In normal mode the subwoofer is permanently on. This may result in low level hum or noise if the rest of the system is switched off and the subwoofer is left switched on. Setting the AUTO switch to ON automatically turns the subwoofer on when a signal is detected at any of the inputs and turns it off (Standby Mode) after a period of inactivity. We recommend the AUTO switch be set to ON for normal operation. In AUTO mode the indicator on the front of the subwoofer will glow RED when the unit is in Standby and GREEN when operational. If your subwoofer is disconnected from the mains or the Power switch is “Off”, the indicator will be extinguished.

If the bass is indistinct or lacks depth, the Phase switch may need adjustment. Set the switch to 0º and listen

This adjusts the blend between the subwoofer and the main speakers. and enables the

Preliminaries

Open the carton and remove all the top packing pieces. Lift the subwoofer out carefully. DO NOT lift the subwoofer out of the carton using the protective bag. The unit is heavy; if you cannot manage it easily, get assistance.

Attaching Spikes

Carefully invert the subwoofer. Protect the top surface from scratches or damage when the subwoofer is inverted.

The subwoofer has four spikes. Prepare the spikes as shown and screw one spike into the threads on the base of teach subwoofer foot. Set the subwoofer upright taking care not to cause damage.

Adjust the spikes in and out until the subwoofer is firm andlevel. Usea spiritlevel toassist you.

Now tighten thenuts securely.

When moving speakers, do not let the spikes pierce objects which may beconcealed undera carpet.

Never drag loudspeakers. If you cannot lift them easily, get someone to assist.

Power Connections

The subwoofer is factory set to operate from the mains voltage marked on the amplifier panel. Before connecting check this voltage is correct for your mains supply.

230 volt products - 220 V to 240 V

115 volt products - 110 Vs to 120 V

If you move to an area with a different mains supply, consult your dealer for advice.

*DO NOT change the operating voltage of this product without seeking expert advice first.

AUTO SWITCH-

When the system is not in use for extended periods, we suggest you switch off the subwoofer to protect it from switching noises.

LOUDSPEAKER SIZES:

usually ‘Large’ or ‘Small’. We recommend that you set the centre and surround speakers to 'Small'. This will direct all the bass in the system to the subwoofer and provide clean, deep and louder bass. Set the ‘Subwoofer’ option on the processor to 'On’ or 'Yes'.

Subwoofer Settings for Front Loudspeakers

Set large floorstanding loudspeakers to ‘large’. Smaller floorstanding loudspeakers may be optionally set to ‘small’. In this case the subwoofer crossover setting should be 55Hz. If you find the bass excessive, set the loudspeaker to ‘large’.

Set bookshelf and stand mounted loudspeakers to ‘small’. If you are using a digital AV processor the subwoofer crossover setting should be 85Hz.

Setting Levels

Once the loudspeaker settings have been finalised, put the AV amplifier into its “Test” mode. Adjust the levels until all channels are equally loud. You may need to adjust the subwoofer output level. Avoid setting too high a level which may limit the subwoofer’s ability to respond to large bass transients. Set a sensible level going into the subwoofer. The subwoofer volume control should be between 12 o’clock and 3 o’clock .

LFE:

If all the speakers are set to ‘Small’, the LFE channel will be combined with the bass from other channels and all this feeds into the subwoofer. When you set the LFE level from your AV processor, use care as the LFE channel may contain powerful low frequencies which may overload a domestic subwoofer. If, during a programme, you hear popping or thumping noises coming from the subwoofer, immediately turn the AV Processor's volume level down and then back off the LFE level. If this does not cure the problem, back off the volume level at the subwoofer.

MS-10. AUTOPOWER operation is built into the subwoofer and cannot be turned on and off.

Many digital AV processors require you to specify the size of speakers in the various channels. These are

MS-CUBE; MS-8; MS-DUO

( your processor instructions),

Read this together with

MS-10

Connecting the MS-10 Subwoofer

INPUT

OUTPUT

VOLUME

LEFT

RIGHT

POWER

AUTO

PHASE

Serial Number

180°

ON0°OFF

WARNING:

TO REDUCE

THE

RISK

FIRE

OR ELECTRICAL

SHOCK,

DO NOT EXPOSE

THIS

PRODUCT TO

RAIN

OR MOISTURE

CAUTION: ATTENTION:

OFF ON

REPLACER

FUSIBLE.

UTILISER UNFUSIBLE

RECHANGE

DE MEMETYPE

CALIBRE

DISCONNECT

SUPPLY

CORD

BEFORE CHANGING

FUSE.

REPLACE ONLY

WITH

SAME

TYPE

FUSE

AND

RATING

35Hz

45Hz

55Hz

65Hz

75Hz

85Hz

AC220-240V 50Hz 150W

FUSE T3.15AL250V

CROSSOVER FREQUENCY

0 10

Power Inlet

Power

SPEAKER

LEVEL

INPUTS

The Mission and Powered SubwoofersMS-8 MS-CUBE

A/V Processor Connections

Your subwoofer has been designed for optimum performance with a Digital processor. If your AV processor has a line level or LFE subwoofer output you should use this connection. You will need to purchase a single screened RCA phono lead from your dealer. Connect this lead to the LFE/R input of the Subwoofer as shown.

Alternatively, you may use a split mono lead from the processor to both inputs of the subwoofer. In this case the input level at the subwoofer will be slightly higher.

Stereo Line Output Connections

If your amplifier has a spare preamplifier output or a stereo subwoofer output, connect the sub-woofer as shown. You will need a stereo screened RCA phono cable.

Pre Out - Main In Connections

If you use a stereo pre and power amplifier, or a stereo amplifier where the pre and main amplifier can be separated, connect the sub-woofer as shown. You will need two screened RCA ‘Y’ adaptors and two single RCA phono cables.

Remove the Pre-Main links on your amplifier. Connect the RCA ‘Y’ adaptors and cables as shown. Connect one leg of the ‘Y’ adaptor to the Left Channel Pre Out socket on the amplifier and the other leg to the Left Channel Main In socket. Connect the remaining plug on this combination to the Left Channel Line Level Input on the sub-woofer. Repeat this for the Right Channel.

Speaker Level Connections

The high level Speaker connections should be used only if your amplifier does not have a line level subwoofer output. In this connection the subwoofer is fed together with the Front loudspeakers. For this you will need two extra twin core cables.

AV AMPLIFIER

Subwoofer Out (Line Level)

CENTRE FRONTREAR

AV AMPLIFIER

CENTRE FRONTREAR

Stereo Outputs (Line Level)

PRE

OUT

MAIN

AMPLIFIER

LEFTLEFT RIGHTRIGHT

LEFTRIGHT

TO FRONT SPEAKERS

AMPLIFIER

(x2)

b c

d e

i j

NUMERICAL KEY

Phase Control

Line Level Outputs

Line Level Inputs

Volume Control

Speaker Level Inputs

LINE LEVEL

c d

i j

Serial Number

FUSE T3.15AL250V

Crossover Frequency Control

Auto Power Switch

Mains Power Indicator

Mains ON/OFF Switch

IEC Mains Input Socket

Mains Power Fuse

Power Inle t

AC220-240V 50Hz 150W

FUSE.

MS-CUBE

Active Subwoofer

N21090

SHOCK,

FUSIBLE.

Measure out two loudspeaker cables of the appropriate length.

Prepare the cables as shown.

Connect the Left Speaker Terminals on the subwoofer to the Front Left speaker terminals on the amplifier. Connect the Red (+) speaker terminal on the amplifier to the Red (+) terminal on the subwoofer. Connect the Black (-) speaker terminal on the amplifier to the Black (-) terminal on the subwoofer. Now connect the Right Speaker terminals on the subwoofer to the Front Right speaker terminals of the amplifier.

RIGHT

SUBWOOFER

SPEAKER LEVEL INPUTS

LEFT

Preliminaries

Open the carton and remove all the top packing pieces. Lift the subwoofer out carefully. DO NOT lift the subwoofer out of

Attaching Spikes ( )

MS-CUBE

Spikes may be fitted if required. To fit the spikes, follow the instructions for the on the previous page.

MS-10

the carton using the protective bag. The unit is heavy; if you cannot

manage it easily, get assistance.

Retain the packing materials. If you decide not to keep the packing, please dispose of it having regard to any recycling regulations in your area. Please retain the user manual. If you

Power Connections

The subwoofer is factory set to operate from the mains voltage marked on the amplifier panel. Before connecting check this voltage is correct for your mains supply.

transfer this equipment to a third party, please ensure all the

instructions are passed on with the product.

230 volt products - 220 V to 240 V

115 volt products - 110 Vs to 120 V

If you move to an area with a different mains supply, consult your dealer for advice.

Positioning your Subwoofer

INPUT

OUTPUT

LEFT

RIGHT

INPUT

OUTPUT

LEFT

RIGHT

Connecting the MS-8 MS-CUBE MS-DUO, and

Although the unit may be placed almost anywhere in the room, even behind the sofa or the TV set, we recommend that it be placed in front of the listener and as central to the listening position as possible. The subwoofer should not

>200mm

be operated within 450mm of a television set as the drive unit magnet may distort the picture.

We suggest you position the subwoofer about 20cm (8 inches) from the wall. A position close to the wall will enhance the bass; placing it across a room corner will increase the bass further, possibly at the expense of clarity. Experiment with a variety of locations and sources before making a final decision.

The drive unit and bass ports move a lot of air at high volume, so make sure you do not place your subwoofer near surfaces or objects that may rattle.

There should be a mains outlet within easy reach.

Your system will perform best if there is a clear line of sight between the subwoofer and the listening position.

NOTE: When running signal cables to the subwoofer, keep them clear of obstructions. Do not run a long signal cable close to mains cables or cables carrying heavy digital traffic.

The MS-8 MS-CUBE MS-DUO, and feature identical connectivity and are connected to the rest of your system in exactly

the same way.

AV AMPLIFIER

A/V Processor Connections

CENTRE FRONTREAR

Subwoofer Out (Line Level)

LEFTLEFT RIGHTRIGHT

dealer. Connect this lead to the Left line input of the Subwoofer as shown opposite.

Alternatively, you may use a split mono lead from the processor to both inputs of the subwoofer. In this case the input level at the

CENTRE FRONTREAR

LEFTLEFT RIGHTRIGHT

subwoofer will be slightly higher.

Stereo Line Output Connections

AV AMPLIFIER

If your amplifier has a spare preamplifier output or a stereo subwoofer output, connect the sub-woofer as shown. You will need a stereo screened RCA phono cable.

CENTRE FRONTREAR

LEFTLEFT RIGHTRIGHT

Stereo Outputs (Line Level)

Pre Out - Main In Connections

Speaker Level Connections

Measure out two loudspeaker cables of the appropriate length.

Prepare the cables as shown.

PRE

OUT

MAIN

AMPLIFIER

RIGHT

(x2)

LEFTRIGHT

TO FRONT SPEAKERS

AMPLIFIER

LEFT

SUBWOOFER

SPEAKER LEVEL INPUTS

Connect the Left Speaker Terminals on the subwoofer to the Front Left speaker terminals on the amplifier. Connect the Red (+) speaker terminal on the amplifier to the Red (+) terminal on the

subwoofer. Connect the Black (-) speaker terminal on the amplifier to the Black (-) terminal on the subwoofer. Now connect the Right Speaker terminals on the subwoofer to the Front Right speaker terminals of the amplifier.

Mission MS-CUBE, MS-8, MS-DUO, MS-10 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual