MINOURA Wheel Display Attachment 3 User Manual

How To Assemble

Wheel Display Attachment

Important Notices

• For displaying a pair of bicycle wheel set only. Do
not use for any other purpose.

• Fits 9mm quick release and standard nut type hub
axles. Any thru axle type hub is not compatible.

• When installing WA-3 on the pillar, you need to
disassemble the clamp and re-assemble it with
proper procedure. Follow the instructions below.

• The clamp is designed to t the tube diameter
between 38mm (1-1/2") and 45mm (1-3/4"). When
installing on 43mm (1-5/8") or smaller diameter,
use the gray plastic shim in the clamp arms.

• When installing the wheel with 9mm quick release
skewer, the nut side must be put on the arm.
Opposite direction should give damage to the
acorn spring. Ideally, you should put a spacer
between the hub and the quick lever side for better
balance.

• Max load on WA-3 is 4 kgs.

WA-3

instructions manual

(ver.1.0 2012/2)

Required Tools: 1 x M5 Hex Wrench

The following explanation focuses on the clamp only,
so we don't show the attachments here.

Pivot Pin Fixing Screw

1

Flat Washer

Once disassemble the
clamp to remove Pivot
Pin, Pivot Pin Fixing
Screw and Clamp
Tightening Screw,
then opne the clamp
arm.

Clamp Body

Clamp Tightening
Screw

Pivot Pin

2

Wind the clamp arm
around the pillar.
Make sure that the
single-arm is located
the right side and the
double-arm is located
on the left side.

Pillar
(larger
diameter)

- 1 -

!

Install the supplied plastic
shim in the clamp only
when installing on 43mm
or smaller diameter pillar.
Make sure the parallel
ribs are located on the
single-arm side.

3

Put the Pivot Pin through all
three (3) holes of the clamp from
the bottom.
Screw the Pivot Pin Fixing Screw
with a flat washer into the pin.

If you have put the Pivot

!

Pin from top side, you
will not be able to screw
it with a hex wrench.

Do not rmly tighten

!

the Pivot Pin Fixing

Screw yet, otherwise the
next step will become

difcult.

Pillar
(smaller
diameter)

Put the shim

4

Contact

Turn the Pivot Pin to align the
thread hole and the hole on the
clamp body.
Screw the Clamp Tightening
Screw into the Pivot Pin.

5

To fix the clamp finally,

1) tighten the Clamp
Tighteninig Screw first,
then

2) tighten the Pivot Pin
Fixing Screw.

Wrong procedure

!

cannot hold the

clamp rmly and
it's dangerous.

②

①

If you need help, contact the shop you originally
purchased this product rst, or the distributor in
your country. The distributor information is found on
Minoura web site.
When you cannot get any good service from them,
you can contact us directly.

MINOURA North America

(for U.S. residents only)

Hayward, California, U.S.A.

Phone [phone] / Fax [phone]

[e-mail]

MINOURA Japan Headquarters

(for ALL customers)

1197-1 Godo, Anpachi, Gifu 503-2305 Japan

Phone [phone] / Fax [phone]

[e-mail] / www.minoura.jp

Made in Japan

Using WA-3

Required Tools:

1 x M4 Hex Wrench / 1 x 10mm Spanner

The arm angle is adjustable
in 4 positions by changing
the lock pin position.

Max Load = 4 kgs

!

- 2 -