MINOURA VERGO-TF Instruction Manual

VERGO-TF

Wheel Holder

– instructions manual

(ver.1.4 2017/8)

Example Style:

Installing on the rail end of
VERGO-TF2 with two bikes

About The Wheel Holder

• Front wheel needs to be removed to mount bike to VERGO-TF. This Wheel Holder safely holds the

removed wheel without worry of damaging your wheel or car.

• Can hold up to two wheels on the single arm. For standard 9mm quick release type wheel only. Any other
system such as Thru Axle type hub cannot be used.

Parts Name

Wheel Installation Position #1

Wheel Installation Position #2

Please note, the hole

!

diameters are different
between the right and
left sides.

Knob Bolt

Angle Adjust
Knob Nut

Arm

For More Information

MINOURA Japan Headquarters

Fax: [phone]
Email: [e-mail]
Web: www.minoura.jp

MINOURA North America

Phone: [phone]
Fax: [phone]
Email: [e-mail]

1197-1 Godo, Anpachi, Gifu 503-2305 Japan

(for U.S. residents only)

Hayward, California, U.S.A.

Warranty Period

Made in Japan

(for ALL customers)

Plate Nut

Bracket

Minoura offers 1-year limited warranty to the original user from
the date of your purchase.
This program covers any defects caused by the manufacturer's
mistakes during production. It will not cover any results caused
by the user's misuse, natural wear or unauthorized modifications.
For more information, visit www.minoura.jp.

How To Install Wheel Holder

How To Mount Wheels

Put the Knob Bolt into the hole on the Bracket, and

1

screw into the Plate Nut slightly as the bolt tip doesn't
come out from the Plate Nut.

Loosen the small knob bolt under the End Base and

2

remove the End Base from the Rail.
Insert the Plate Nut into the upper gutter on the Rail.

Rail

Install the End Base

3

to the Rail again.
Tighten the Knob Bolt to hold the
Wheel Holder securely.

End Base

How To Fold Down The Arm

When not in use, you can fold down the arm compactly.

1

Be sure these hole sizes are
different between the right side
and the left side.
The wheel must be installed on
the larger hole side.
If necessary, turn the Arm to
match your desired direction.

Wheel on position #1

Wheel on position #2
(wheel installation
direction is disignated)

You don't have to remove the quick release

skewer from the wheel when mounting the
wheel on both position #1 and #2.

Be sure the quick lever is located outside on

both cases.

Wheel Installation Position #1

Loosen the skewer nut, push the lever side shaft
to make large space on the nut side.
Drop your wheel into the cut out on the top of the
arm and close the lever to lock securely.

2

3

Fold down the arm

Loosen the Knob Bolt
to turn the Bracket

Wheel Installation Position #2

Remove both skewer nut and the acorn spring
then insert the shaft together with the 9mm
diameter threaded end into the LARGER hole.
Tighten the nut and spring, then fold down the
lever to lock securely.

Only the case of using position #2, if the

!

!

!

acorn spring has been damaged due to

the twisting of the Q/R lever, try to ip

the spring as the larger diameter side
facing inward.

The arm is made of hollow alloy tubing.
Tightening too much can damage it.
If you have tightened the skewer too
strongly, the arm could be damaged.
Adjust the clamping force just enough
to hold the wheel in place.

Minoura recommends that the wheel be

just touching the oor, not suspended in

the air.

Even if you tighten the knob rmly, it
would be difcult to keep the wheels in

the air.