Minoura RS-1100 User Manual

RS-1100 Bike Fellow 2 Repair Stand
INSTRUCTION MANUAL
Thank you for purchasing the Minoura RS-1100 repair stand. This foldable, light weight multi purpose stand allows you to use it as both a repair stand and a display stand. A convenient Carrying Bag with a tool pocket is available as an option.
IMPORTANT NOTES:
RESOLUTION DIAGRAM
Knob Bolt - C
BB Support Bracket
BB Support Lock Button
Seat Tube Support Bracket
Seat Tube Stay
Down Tube Supporter
Front Tire Stopper
Arm
Knob Bolt - B
Upper Frame
Knob Bolt - A
Lower Frame
Lock Release Button
Leg - A
- Page : 1 -
HOW TO ASSEMBLE
¶ No tools are required to assemble your RS-1100.
Loosen Knob Bolt-A on Lower Frame, slide up Upper Frame, and tighten again Knob Bolt-A slightly (see Fig. 1) .
!
!
(Fig. 1)
Open Leg-A fully until the leg locks (clicks) in place. When you hear the click sound, Leg-A is locked automatically. After that, open Leg-B fully, then place this stand on the floor (see Fig. 2) .
!
!
(Fig. 2)
(Fig. 3)
-Page : 2 -
(Fig. 4)
Turn both Arm and Seat Tube Stay fully. Insert Seat Tube Support Bracket through and into the Seat Tube Stay, and insert the plastic cap. (see Fig. 5)
The BB Support Bracket will help your bike stable during on this stand. The BB Support Bracket will open auto­matically when you open Arm. (see Fig. 6)
(Fig. 5)
If you don’t wish to use BB Support Bracket or if you wish to fold this stand, push the Lock Button on the bottom of the Arm. The BB Support Bracket may then folded up or down. (see Fig. 7)
When you wish to fold the legs, you must keep pressing each Lock Release Button on the Leg­B, then fold the Leg-A. (see Fig. 8)
(Fig. 6)
(Fig. 7)
(Fig. 8)
- Page : 3 -
USE RS-1100 AS A REPAIR STAND
Place RS-1100 on a flat stable surface. Pull up the Arm Stopper and insert it into the angled hollow firmly to lock it (see Fig. 9) .
!
To begin set the left side crank arm downward or a little forward, then twist your bike about 20 degrees counter-clockwise and lift it up.
Arm Stopper
(Fig. 9)
(see Fig. 10)
!
Place the down tube onto both Down Tube Supporters gently. (see Fig. 12)
(Fig. 10)
(Fig. 11)
!
-Page : 4 -
(Fig. 12)
Then support the seat tube with Seat Tube Support Bracket. Adjust the position of the bracket not to pinch the cable. The bike is supported safely . (see Fig. 13)
Adjust the angle of Arm with Knob Bolt-B in order to fit all contact points to the bike. Make sure all contact points are supporting the bike properly. (see Fig. 14)
Finally, sandwich the front wheel with both Front Tire Supporters. This device will make your bike stable and help your work securely while the bike is on this stand. (see Fig. 14)
(Fig. 13)
(Fig. 14)
USE RS-1100 AS A DISPLAY STAND
¶ RS-1100 also can be used as a display stand or temporary bike stand.
Place the RS-1100 on a flat and horizontal floor. Pull the Arm Stopper out fron the slot and lay it down. (see Fig. 15)
!
Push the Lock Button of the Arm and fold down the BB Support Bracket.
(Fig. 15)
Then turn the Arm horizontally. (see Fig. 16)
(Fig. 16)
- Page : 5 -
Place the top tube down softly on both Down Tube Supporter. (see Fig.
17)
!
FOR WARRANTY, MORE INFORMATION
CONTACT :
MINOURA WARRANTY CENTER
1415 San Mateo Avenue, South San Francisco, CA 94080 U.S.A.
(Fig. 17)
Toll Free: 800-601-9592
MINOURA NORTH AMERICA
37653 B Argyle Rd. Fremont, CA 94536 U.S.A. Phone: 1-510-739-1395 Fax: 1-510-790-1108 E-mail: MinouraUSA@IBM.net
MINOURA JAPAN
1197-1 Godo, Anpachi Gifu 503-2305 JAPAN Phone: 81-584-27-3131 Fax: 81-584-27-4258 E-mail: Minoura@Minoura.co.jp URL: http:// www.minoura.co.jp
-Page : 6 -
Loading...