M
V
S
2
0
U
S
E
R
M
V
S
2
0
U
S
E
M
V
S
2
0
U
S
E
R
R
M
M
M
A
A
A
N
N
N
U
U
U
A
A
A
L
L
L
inipack-america LLC
M
832 N. Glassell Street
ddress
A
Tel
Fax
-mail
E
nternet
I
1
range, CA USA
O
2865-4322
9
(+ 1) 714.283.4200
+ 1) 714.283.4268
(
upport@minipack-america.com
S
ww.minipack-america.com
w
ersion 02.10 MVS 20.EN
V
SER MANUAL MVS 20
U
This manual is for the MVS 20 Vacuum Packer. The general instructions apply to the model in this category. Minipackamerica LLC cannot be held responsible for any damage caused by deviating machine specifications.
This manual has been compiled with the utmost of care. Minipack-america LLC accepts no responsibility for any errors in
this manual and/or the results of misinterpretation of this manual.
Minipack-america LLC is not liable for damages and/or problems that arise from using spare parts that are not supplied
by Minipack-america LLC
Minipack-america LLC reserves the right to change specifications and/or spare parts without prior notification.
All rights reserved. No part of this publication may be reproduced by photocopy, printing or in any other way without prior
consent from Minipack-america LLC
LIABILITY
. We exclude all liability in so far as it is not provided for by law.
1
2. Our liability shall never exceed the total amount of the order in question.
3. Barring the generally applicable legal rules of public order and good faith we are not liable to pay for any damage of
any sort whatsoever, directly or indirectly, including business losses, to movable or immovable property, or to
persons, either at the opposing party as at third parties.
4. We are in any case not liable for damages arising from or cause by the use of the product supplied or by the
unsuitability of it for the goal for which the other party purchased it.
GUARANTEE
. Subject to the following limitations we give 12 months guarantee on the products supplied by us. This guarantee is
1
limited to manufacturing faults that occur and does therefore not cover breakdowns involving any parts of the
supplied product that are exposed to any form of wear or usage.
2. The guarantee on parts or additions provided from third party suppliers is limited to the guarantee provided us by
the third party supplier.
3. The guarantee expires if the other party and/or third parties engaged by him use the supplied product
incompetently.
4. The guarantee also expires if the other party and/or third parties engaged by him carry out activities on i.e. make
modifications to the supplied product.
5. If we replace parts in compliance with the obligations of this guarantee then the replaced parts become our
property.
6. If the other party does not, not sufficiently, or not in a timely fashion fulfil any of the obligations arising from the
agreement reached between the parties then we are not obliged to provide this guarantee as long as the situation
is occurring.
The stipulations of the guarantee and liability are part of the general terms and conditions of sale which will be sent to
you if requested.
ersion 01.10 VMS 20.EN 2
V
SER MANUAL MVS 20
2
3
8
U
CONTENT USER MANUAL
NTRODUCTION / LIABILITY /
I
GUARANTEE
ONTENT USER MANUAL ……….…………………………………………………………..
C
ACHINE REGISTRATIE ……….…………………………………………………………..
M
…….……………………………………………………………..
4
MPORTANT FOR INSTALLATION – READ THIS FIRST !!!! ..……………………………………………..
I
MPORTANT FOR OPERATION – READ THIS FIRST !!!! ………………………………………………
I
ARNING LABELS ……….…………………………………………………………..
W
MPORTANT MACHINE PARTS ……….…………………………………………………………..
I
TART UP AND OPERATION ……….…………………………………………………………..
S
N/OFF switch 9
ONTROL PANEL ……….…………………………………………………………..
C
ACHINE MAINTENANCE ……….…………………………………………………………..
M
O
tart the machine 9
S
tandard user operations 10
S
ontrol panel version 11
C
ontrol panel layout 11
C
ontrol panel use 12
C
eneral 14
G
mportant before and during maintenance 14
I
tandard maintenance schedule 15
S
acuum pump maintenance 15
V
eal system maintenance 18
S
ilicone holder and lid gasket maintenance 21
S
ist of maintenance parts 22
L
5
6
7
9
1
1
4
1
ECHNICAL SPECIFICATIONS ……….…………………………………………………………..
T
LECTRICAL DIAGRAMS ……….…………………………………………………………..
E
rror code 25
NEUMATIC DIAGRAMS ……….…………………………………………………………..
P
ROBLEM SOLVING ……….…………………………………………………………..
P
PECIAL APPLICATIONS ……….…………………………………………………………..
S
EMOVAL FRONT PANEL ……….…………………………………………………………..
R
E
ackaging liquid products 29
P
3
2
4
2
6
2
7
2
9
2
0
3
ersion 01.10 VMS 20.EN 3
V
SER MANUAL MVS 20
U
egister the machine using the following data. This information is necessary if the supplier or Minipack-america LLC is
R
contacted concerning questions or references about the specific machine.
RIOR TO STARTING TO USE THE MACHINE,
P
MACHINE REGISTRATION TO BE COMPLETED BY THE USER
DATA ON MACHINE TAG
Relevant data for answering questions can be found on the machine tag. The machine tag is located at the rear of the
machine. Note down the following data:
1. MACHINE TYPE
2. MACHINE NUMBER (MACHINE NO.)
3. VOLTAGE (TENSION)
CONTROL PANEL DATA
When starting the machine two codes first appear on the display in succession before control switches to user mode.
The first code indicates the software version of the control software and the second code indicates the options active.
Write both codes in the space below:
4. CODE 1
5. CODE 2
ersion 01.10 VMS 20.EN 4
V
SER MANUAL MVS 20
U
IMPORTANT FOR INSTALLATION !!! READ THIS FIRST !!!
ENERAL
G
First read this manual carefully before the machine is put into operation. This manual contains relevant information
and instructions for starting up, maintenance and applications. If problems arise with the machine that could have
been avoided by referring to this manual then the guarantee expires.
Minipack-america LLC wishes the customer lots of pleasure for an extended period from the purchase of the
machine. If there are any problems or questions then the customer can always approach the supplier or Minipackamerica LLC.
ENVIRONMENT
The machine must be moved or transported in an upright position. The machine may NOT be tilted as this can cause
damage to the pump.
Place the machine on a flat, level floor. This is essential for problem free operation of the machine.
Enough space must be left around the machine for good ventilation. The space must be at least 5 centimetres.
The ambient temperature in which the machine is operated must be between 41 0 F and 86 0 F. When operating the
machine in other ambient temperatures the user must contact the supplier or Minipack-america LLC for advice.
NEVER place the machine directly next to a heat source or a steaming device (for example a combo-steamer,
dishwasher or stove).
POWER / EARTH
Check that the voltage stated on the machine tag is the same as the mains voltage.
Always connect the machine correctly to an earthed socket to avoid danger for fire or electrical shocks (earth
connection is green/yellow).
The power cable must always be free and nothing may be placed on it.
Replace the power cable immediately if damaged.
Always disconnect the power if there are problems with the machine or during maintenance, prior to starting work on
the machine.
If the machine is stationary for long periods then the power should always be disconnected.
ersion 01.10 VMS 20.EN 5
V
SER MANUAL MVS 20
U
VACUUM PUMP
Check before starting the machine if there is oil in the pump (see page 16). NEVER start the machine without oil in
the pump.
Use the right type of oil for the pump (see page 16).
After moving and/or transporting the machine, always first check the oil level before re-starting operation.
When starting the machine for the first time or after a lengthy idle period first run the conditioning programme before
operating the machine (see page 15).
IMPORTANT FOR OPERATION !!! READ THIS FIRST !!!
ENERAL
G
Never pack products that can be damaged during or after vacuum packaging. Live oats may never be vacuumed.
Refer to this manual if in doubt as to the operation and/or functioning of the machine. If the manual does not offer a
solution consult the supplier or Minipack-america LLC.
The guarantee and/or liability expires if damage is caused by repairs and/or changes made by you. In the case of
malfunctions contact the supplier or Minipack-america LLC.
In the case of malfunctions always stop the machine and remove the power cable from the wall socket.
GENERAL MAINTENANCE
It is essential that the machine is serviced regularly to guarantee operation and to keep the machine in optimal
condition. The maintenance schedule is clearly defined on page 15. The guarantee automatically expires due to
overdue or sloppy maintenance.
Always remove the power cable from the wall socket for maintenance work, the machine must be completely
disconnected.
If there are doubts about the maintenance activities or if the machine fails to work correctly always contact the
supplier or Minipack-america LLC.
ersion 01.10 VMS 20.EN 6
V
SER MANUAL MVS 20
U
TRANSPARENT LID
Never locate the machine near a heat source. This can cause damage to the lid (cracks).
Never place hot, sharp, or heavy objects on the lid. These can cause damage to the cover (cracks) in the long run.
Always clean the cover with solvent-free cleaning agents. Solvents can damage the lid.
Check at least once a week if there are cracks in the lid. If cracks are visible in the lid then the machine must
IMMEDIATELY be turned off and not used again until the lid has been replaced. Continuing to work with a cracked lid
can cause the lid to implode. All guarantees and/or liability expire in the case of accidents and/or damage caused by
working with a cracked lid.
Replace the transparent cover every 4 years as a precautionary measure as a standard maintenance interval.
VACUUM PUMP
Regularly check the level and quality of the oil in the pump. If too little oil or the quality of the oil is bad (turbid),
replace or top up the oil before operating the machine (see page 16). Let the pump conditioning program run at least
one full cycle before replacing the oil (see page 15).
Use the right type of oil for the pump when replacing or topping up (see page 16).
Use the conditioning program at least once a week to enhance correct and long-lasting pump operation (see page
15).
WARNING SIGNS ON THE MACHINE !!!
NLY use the prescribed power supply voltage.
O
Insert the plug firmly into the mains wall socket.
Always connect the machine to an earthed wall socket.
Always remove the plug during maintenance or when the machine is not in use for extended periods.
ersion 01.10 VMS 20.EN 7
V
SER MANUAL MVS 20
1
2 3
4 5
6
7
1
.
S
ealing bar in vacuum chamber mounted sealing supports with a click system
O
il inspection
11
O
n/Off switch and fuse holder is situated a
t
the back side of
9 10
8
12
13 14
1
U
MPORTANT MACHINE PARTS
I
. Silicone holder mounted on transparent lid
2
3. Lid gasket in lid for hermetic seal
4. Gas springs for opening lid after machine cycle
5. Vacuum / Ventilation opening
6. Control panel
7. Vacuum pressure meter
8. ON/OFF Switch
9. Oil drain plug
10. Oil fill plug
11. Oil inspection window
12. Power cable
13. Fuse holder with fuses
14. Warning stickers
Appearance of parts and machines can deviate per model from illustrations
he machine.
t
indow is situated at
w
the back side of the
machine.
ersion 01.10 VMS 20.EN 8
V
SER MANUAL MVS 20
U
TARTING AND OPERATING THE MACHINE
S
N/OFF SWITCH
O
The ON/OFF switch is situated at the back side of the machine and is used to turn the machine on and
off before and after operation.
CAUTION – The ON/OFF switch does not completely remove all power from the machine. The power
cable must be unplugged from the wall socket to remove all power from the machine. Ensure that the
machine is completely without power during maintenance and repair activities is.
When the machine is turned on (with the ON/OFF switch), then the pump only runs during the vacuum cycle.
START MACHINE
When the machine is connected, then the machine can be turned on using the ON/OFF switch. When
starting the machine two codes first appear in succession on the display before control switches to
user mode.
The first code indicates the control software version. The second code indicates the machines active
options. Note both codes on page 4 of this manual as they are important for the supplier or Minipackamerica LLC when making enquiries and/or if any problems arise.
After switching to user mode the machine is ready for use. If the machine is new or has not been
used for an extended period, then it is important to run the conditioning program for the pump (15
minutes) to maintain the pump. For instructions on the conditioning programme, see page 15.
After switching to the user mode the display could read [ OIL ]. This means that the operating hours
counter is turned on and the set number of operating hours has elapsed. The hour counter is
turned off by default but the client supplier can use it as a reminder for regular maintenance
activities.
When [Oil] is displayed the machine can be still be used as usual but it is advisable to either turn off
the hour counter or to reset it.
Contact the supplier or Minipack-america LLC for more information about setting or turning off the
operating hours counter.
ersion 01.10 VMS 20.EN 9
V
SER MANUAL MVS 20
h
e [VACUUM STOP] key or the [STOP] key.
U
STANDARD USER OPERATIONS FOR THE MACHINE
1. Turn the machine on with the ON/OFF switch. Warm the pump up with the condition programme if the machine has
stood idle for some time (instructions page 15).
2. Fill the vacuum bag with product. Select the correct format bag that easily fits around the product but is not too
large for the product. Ensure hygienic conditions during this operation. Packaging materials, product and hands
must be clean and if possible dry.
3. Lay the vacuum bag in the chamber. The open side must be laid over the sealing bar. The bag may however not
extrude from the chamber. If the product is a lot lower than the height of the sealing bar then insert plates that are
supplied standard with the machine can be used. This makes the operation easier and reduces the cycle time.
4. The vacuum bag must be placed over the sealing bar without any folds.
5. Multiple vacuum bags can be placed over the sealing bar if the sealing bar is longer than the opening of the
vacuum bag. Vacuum bags may not however be laid on top of each other on the bar.
6. Set the correct value for vacuum and sealing functions. See page 13 for setting the function values.
7. Close the lid and the machine automatically runs through the full cycle of installed functions. The lid opens
automatically when the last function “ventilation” has finished.
8. If necessary the cycle can be fully or partially interrupted by pressing t
he [VACUUM STOP] key interrupts the active function (vacuum or sealing) and automatically continues with the
T
next function.
The [STOP] key interrupts the entire cycle and goes immediately to the ventilation function.
9. The packed product can be removed from the machine.
SAFETY and PRODUCT PROTECTION
The packing process can be partially or fully interrupted at all times:
Stop active function, press on [VACUUM STOP] key
Stop full machine cycle, press [STOP] key
OPTIMAL AND EFFICIENT PACKAGING RESULT
se the correct format and good quality vacuum bags
U
Maximum 75% product filling in vacuum bag
Place vacuum bag fold free over seal beam (use correct number in inlay plates in chamber)
ersion 01.10 VMS 20.EN 10
V
SER MANUAL MVS 20
-
1
0,20,40,60
,8
1 2 3 5 4 4 7 6
U
CONTROL PANEL
ONTROL PANEL VERSION
C
Digital time control
The value of the functions can be set for a certain time period.
CONTROL PANEL LAYOUT
1. Display
isplays the status of the active function during the run of the program cycle or the set value of the selected function
D
when machine is not running.
2. FUNCTION SELECTION Key
elect function (vacuum or seal) for viewing or changing function values. The function is selected if the function light is
S
on in front of the function description under the display.
3. CONDITIONING PROGRAMME Key
tart the conditioning program for pump (duration 15 minutes). For instructions on the program, see page 15.
S
4. FUNCTION Lights
light in front of the function indicates that the function is active during the program cycle or that the function is selected
A
for view or change.
®
The digital control is implemented with a function program that can be set with different
function values per cycle (to be able to pack different products). A program cycle is the
complete program of set functions (vacuum and seal) that the machine runs through to
package a product.
The control panel is implemented standard with a conditioning program for the regular
maintenance of the pump and two STOP keys for complete function interruption or for only
active function interruption. There are also a number of built-in service programs. Contact the
supplier or Minipack-america LLC for more information about these functions.
The vacuum function can be set to whole seconds with a maximum of 99 seconds.
The seal function can be set with an interval of 0.1 seconds and a maximum of 6.0 seconds.
0
ersion 01.10 VMS 20.EN 11
V
SER MANUAL MVS 20
U
5. + / STOP VACUUM Key
unction during cycle Interruption of the active function during the program cycle. The cycle immediately
F
General function. Increment the value of the selected function.
6. - / STOP Key
unction during cycle Terminates the program cycle completely. The cycle immediately switches into the
F
General function Decrement the value of the selected function.
7. Vacuum meter
isplays the pressure in the vacuum chamber.
D
8. ON/OFF Switch
he ON/OFF switch is used to turn the machine on and off before and after operation. The switch turns on all units in the
T
machine. Caution, the switch does not completely remove all power from the machine.
continues with the next function.
ventilation function.
CONTROL PANEL USE
When the machine is turned on it is ready for use once the two operating codes have displayed.
Description of the program cycle for digital time control
. Functions (vacuum and sealing) are set with the correct values (see page 13 for settings)
1
2. Close the lid.
3. Vacuum function The machine starts to vacuum the chamber.
The light in front of [VACUUM] goes on.
Display : decrementing time per second starting at the time set (max. 99 sec.).
Vacuum meter starts increasing to the left.
4. Sealing function Once the vacuum function is finished, the sealing function starts to seal the vacuum bag(s).
The light in front of [SEAL] goes on.
Display : decrementing time per 0.1 second starting at the time set (max. 6.0 sec.).
The reading on the vacuum meter stays the same.
5. Ventilating function After ending the seal function the ventilating function starts ventilating the chamber to 1
atmosphere/ATO and the lid opens.
There are no longer any lights on in front of the functions.
Display : lines moving up and down until the lid is opened.
The vacuum meter runs back to the right to zero and the lid opens automatically.
6. The product is packed and ready to remove.
ersion 01.10 VMS 20.EN 12
V
SER MANUAL MVS 20
U
Set/change function values
The following steps must be followed to change the function values for vacuum and/or seal :
Press the FUNCTION SELECT Key to select the required function. The function light will light up when the function is
selected.
Press the [+ / STOP VACUUM] or [- / STOP] keys for incrementing or decrementing the function values respectively. It
takes 0.5 seconds before the value begins to change.
After changing the value(s) the machine must run through the cycle once (see previous page) to record the values.
Vacuum function
he vacuum function value can be incremented or decremented per second with a maximum of 99 seconds and a
T
minimum of 2 seconds.
If while changing the vacuum function setting the [+ / STOP VACUUM] or [- / STOP] key is held down then the first 5
seconds will be incremented or decremented per second. Then intervals of 10 seconds will appear. If the key is released
then the settings can be changed again per second.
Sealing function
he seal function setting can be increased or decreased with a maximum of 6.0 sec. and a minimum of 0.5 sec.
T
If while changing the seal function setting the [+ / STOP VACUUM] or [- / STOP] key is held down then the first 0.5
seconds will be incremented or decremented per 0.1 second. Then intervals of 1.0 second will appear. If the key is
released then the settings can be changed again per 0.1 second.
Service programs control panel
he control panel is also equipped with a number of service programs that can be useful during regular maintenance or
T
repairs. The conditioning program for the pump is the most used service program (see explanation on page 15).
Contact the supplier or Minipack-america LLC for more information about the use of other service programs.
ersion 01.10 VMS 20.EN 13
V
SER MANUAL MVS 20
U
MACHINE MAINTENANCE
ENERAL
G
Regular, thorough maintenance is essential for extending the machine's life, for preventing malfunctions and for
achieving an optimal packaging result. If the machine is used intensively (more than 5 hours per day) then it is a
professional service is recommended every 6 months. In other cases one complete service per year is sufficient
(depending on location, environment and products).
There are however also small maintenance activities that must be carried out more regularly and that the user can do
himself. The following page contains an overview of these activities.
IMPORTANT BEFORE AND DURING MAINTENANCE
The machine must always be completely voltage free before any maintenance is carried out on it. Always remove the
plug from the wall socket.
If the machine is not functioning properly or if it produces strange noises, turn it off immediately with the ON/OFF
switch and contact the supplier or Minipack-america LLC.
When cleaning transparent lids NEVER use cleaning agents containing solvents. Check at least once a week if there
are cracks in the lid. In case of cracks, turn off the machine immediately and contact the supplier or Minipackamerica LLC.
High pressure cleaning is not permitted for cleaning the machine. High pressure cleaning can cause considerable
damage to electronic and other parts of the machine.
Water may never be permitted to enter either the extraction nozzle of the chamber or the blow-off hole of the pump.
This would cause irreparable damage to the pump.
Larger services must always be carried out by an authorised supplier.
The MVS 20 machine is designed for a maximum of 5 hours per day. The supplier or Minipack-america LLC cannot
be held responsible for any malfunctions or defects if these operating limits are clearly exceeded without
consultation.
The machine must be moved or transported in an upright position. The machine may NOT be tilted as this can cause
damage to the pump.
The supplier or Minipack-america LLC cannot be held responsible for any malfunctions or defects if the maintenance
instructions in this manual are not followed.
ersion 01.10 VMS 20.EN 14
V
SER MANUAL MVS 20
U
TANDARD MAINTENANCE SCHEDULE FOR THE MACHINE
S
Daily Clean the vacuum chamber, lid and housing after use with a damp cloth.
Be careful that no cleaning agents containing solvents are used.
Make sure that no high pressure cleaner is used.
Weekly Check the oil level and replace or top up oil if the oil is turbid or the oil level is too low.
For instructions, see page 16.
Activate the conditioning program for the pump at least once a week.
Check the seal beam for damage. Replace Teflon tape/seal wire if the seal quality is
no longer sufficient or if the Teflon tape/seal wire is no longer taught on the bar. For
instructions, see page 19-20.
Check the lid gasket and replace it if the gasket is damaged or stretched. For
instructions, see page 21.
Inspect the transparent lid for cracks. If cracks are visible, turn off the machine
immediately and contact the supplier or Minipack-america LLC.
Every Six Months Replace oil at least once every 6 months.
Yearly Inspect the oil exhaust filter for saturation. If saturated, replace the filter. For
instructions, see page 17.
Contact the supplier for a professional service
Four-yearly Replace transparent lid and the gas springs
Replace seal cylinder membranes.
VACUUM PUMP MAINTENANCE
It is very important to regularly service the pump to ensure extended and correct operation. The following activities are
essential for correct maintenance. If the machine is used regularly then it is advisable to have the pump fully inspected at
least once a year by the supplier to ensure extended and problem free operation. Contact the supplier or Minipackamerica LLC for more advice and information.
Conditioning program
The conditioning program ensures that the pump is thoroughly rinsed. During the programme the pump and oil reaches
operating temperature so that the oil can better absorb any moisture and contaminants and filter them. The high
temperature enables any moisture in the pump to evaporate minimising the risk for corrosion in the pump.
The program lasts 15 minutes and it is advisable to run it at least once a week. Turn on the machine, press the key
[conditioning program], and close the lid. The program runs automatically. During the program the display will display
moving dots.
The program can be interrupted at any time using the [STOP] key. It is however important for the sake of good
maintenance that the program completes a full 15 minute cycle and therefore advisable only to interrupt the cycle for
something urgent.
It is also advisable to run the program before using the machine for the first time, after the machine has been stationary
for a lengthy period of time, and especially prior to changing oil.
ersion 01.10 VMS 20.EN 15
V
SER MANUAL MVS 20
T
ake care to use the correct
S
ituation after the rear
1 2
3
1
.
Oil
fill plug
U
Changing Oil / Filling Up
The oil level and oil quality must be checked at least once a week. The oil inspection window serves this purpose. Top
up the oil level if it is too low. Replace the oil if it is turbid. Oil must be replaced at least once every 6 months.
1. Oil fill plug
2. Oil drain plug
3. Oil inspection win
over plate is removed.
c
ype of oil for the pump
t
Beware of hot oil fumes
during drainage
CAUTION, when unscrewing hot oil fumes can escape. The oil now drains from the drain hole (an oil pan must be
placed underneath). When the oil has drained, tilt the machine slightly so that all residual oil can drain off. After draining
the oil drain plug is replaced.
Filling up oil
After draining or if the oil level has dropped, oil needs to be filled up. The oil fill plug must be removed with the correct
size spanner. The pump can now be filled with oil. Make sure that you add the correct amount (see table on page 22)
Slide the component plate backwards to facilitate filling.
TAKE CARE to fill with small amounts at intervals. Fill the oil level to the top of the oil level indicator sticker.
Oil types and amounts
t is important to use the correct type and quantity of oil for the pump. The wrong type or too much oil could damage the
I
pump. The ambient temperature where the machine is operated is also important for the type of oil. See amounts and
types with related ambient temperatures in the table on the next page.
Examples of supplier brands for the standard types of oil are Shell Vitrea, Aral Motanol GM, BP Energol CS, or Texaco
Regal R+ O with related viscosity numbering. If the machine is used outside normal specifications regarding ambient
temperature, contact the supplier or Minipack-america LLC.
Ambient temperature
achine Type Pump
M
VS 20
M
achines are supplied with standard type oil.
M
. Oil sight glass
2
3. Oil drain plug
Draining oil
f the oil is white or turbid when checked then it must be replaced. Before
I
draining off the oil let the conditioning program run a full cycle. The dirt and
moisture is absorbed by the oil and the oil becomes thinner making draining
easier.
After the program has ended the drainage plug can be removed.
Filling
Capacity
4,8 m3/h 0.05 Viscosity VG 22 VM 22
(litres)
Standard
Oil type
50 - 86 o F
“Cold”
Oil type
41 - 50 o F
Hot”
“
Oil type
86 - 104 o F
VS 22
ersion 01.10 VMS 20.EN 16
V
SER MANUAL MVS 20
R
emove the rear cover plate to get excess to the vacuum pump.
R
emove the old filter from the housing
T
ake care that the filter gasket does not
p
laced on the new filter.
U
Inspect and change oil exhaust filter
There is an oil exhaust filter in the pump that absorb and filter oil vapours. The filter will become saturated after a period
of time and needs to be replaced. This is on average between 9 and 18 months. When the filter is saturated it is no
longer possible to achieve maximum vacuum and the machine starts smoking.
Oil exhaust filter
hange oil exhaust filter
C
emove the fixation screw for the base plate where the pump is placed
R
upon.
Now the complete base plate can slide out to have better excess to the
components.
lace the new filter in the housing.
P
Screw the filter on again
emain behind when removing the filter.
r
Take care that the filter gasket is correctly
ersion 01.10 VMS 20.EN 17
V
SER MANUAL MVS 20
D
OUBLE SEAL
CUT-
O
FFSEAL
U
EAL SYSTEM MAINTENANCE
S
The following seal systems are available:
The double seal system is equipped with two 0,138 inch concaved seal wires.
The cut-off seal system is a combination form a 0,197 inch flat seal wire with a 0,035 inch round cut-off wire.
The seal quality is partially dependent on the maintenance of the sealing bar and silicone holder. The main maintenance
activities are the daily cleaning of the sealing bar and silicone holder with a damp cloth and a weekly inspection of the
bars with replacement of the sealing wire, Teflon tape or silicone rubber if irregularities appear on top of the bar or the
seal quality is insufficient.
The sealing bar is clicked onto the seal cylinder shafts and can be removed by lifting the seal bar vertical from the
mentioned shafts.
The steps for replacing the sealing wire and Teflon tape are described on the following pages.
The average maintenance cycle of the sealing bar (Teflon tape / sealing wire) is at least once every 4 months.
(This indication refers to regular use of the machine and packaging standard products with standard vacuum packaging materials. No rights can be
derived from this indication)
ersion 01.10 VMS 20.EN 18
V
SER MANUAL MVS 20
U
REPLACING DAMAGED OR BROKEN SEAL WIRES.
First remove the Top Teflon layer.
o remove old damaged or
T
broken seal wires, follow next
steps;
he seal wire is pulled out of
T
the end block.
efore tighten the seal wire,
B
place back the pressure plate.
Push it completely to the end.
oose the screw of the seal
L
wire that should be changed.
efore replacing the seal wire,
B
check if both springs are in
place, and if the Teflon is good
ow you can tighten the screw
N
to secure the wire. Don’t use
to much force for tightening.
irst pull out the pressure
F
plate.
ush the new seal wire into the
P
end block.
nce both wires are replaced
O
and fixed bend both wires to
the other end of the seal bar.
nce the pressure plate is
O
removed the seal wire can
pulled from the end block.
ush it till it comes out on the
P
other side.
n case of a cut-off seal, check
I
if the cut-off wire is placed
correctly in to the groove.
ow push the wires into the
N
end block on the other side of
the seal bar.
ersion 01.10 VMS 20.EN 19
V
efore tighten the seal wires,
B
first place the pressure plate.
efore placing the Teflon top
B
layer, first check both sides of
the seal bar, if all pressure
plates are placed correctly and
if the spring plates are fully
pushed in.
ighten the seal wire by
T
turning the pliers clockwise.
he correct tension is reached if
T
both spring plates are pushed to the
end block. Both sides of the seal
SER MANUAL MVS 20
U
REPLACING TEFLON TAPE.
Make sure the seal bar is cleaned properly before placing new Teflon.
emove the protection layer
R
from the Teflon.
ut the Teflon at the end of
C
the end block till the table is
reached.
old the Teflon against the
F
seal bar.
lace the Teflon to the edge on
P
the end block, and push the
Teflon firmly on the seal bar.
ut the Teflon at the edge.
C
hen roll over the seal bar
T
while pushing the seal bar to
the table.
o this also on the other side.
D
ut the Teflon diagonal as
C
shown on the picture.
hen stick the Teflon to the
T
other side. Prevent crinkles they
will influence the seal result.
old the remaining Teflon up
F
and push it against the end
block.
ake sure the Teflon is placed
M
without wrinkles, they will
influence a proper seal result.
See page 22
or correct parts and quantities
f
ersion 01.10 VMS 20.EN 20
V
SER MANUAL MVS 20
A
ppearance may differ per model
U
ILICONE HOLDER AND LID GASKET MAINTENANCE
S
Replace the rubber silicone holder
The silicone holder must be inspected weekly for roughness on the silicone rubber (mainly caused by burning by the
sealing wire). If irregularities appear then the silicone rubber must be replaced.
Average maintenance cycle for silicone rubber is at least once every 6 months
(This indication refers to regular use of the machine with standard products. No rights can be derived from this indication)
1. Remove the old silicone rubber from the holder.
2. Cut a new piece of silicone rubber the same size as the old one. The same
size is very important, too short or too long will cause problems with sealing.
3. Place the new piece in the silicone holder. Ensure that the silicone rubber is
completely and evenly placed in the groove. It is also important that the
surface of the silicone rubber is smooth after it is in place and is shows no
signs of tension.
Replace lid gasket
The lid gasket ensures that the vacuum chamber is completely sealed during the
machine cycle. This is essential to achieve a maximum vacuum. The lid gasket wears
due to the extreme pressure differences and must be replaced regularly. Inspect the lid
rubber weekly for tears or damage.
Average maintenance cycle for silicone rubber is at least once every 6 months
(this indication refers to regular use of the machine, on average 5 hours a day and with standard products.
No rights can be derived from this indication)
The length of the new lid gasket is measured against the old rubber. If the lid gasket is too short or too long it can cause
problems closing the lid or leak.
The gasket must be placed evenly and without tension in the holder. The ends must be cut straight and must be laid
tightly against each other to avoid leakage.
ut principle remains the same.
b
ersion 01.10 VMS 20.EN 21
V
SER MANUAL MVS 20
U
LIST OF SERVICE PARTS
VACUUM PUMP PARTS
USCH STANDARD OIL OIL EXHAUST FILTER
B
04 m3/h
0
EAL SYSTEMS
S
ARTS
P
eflon tape
T
ouble seal 2 x 0,138 inch concaved wire 0305000 14,6 inch
D
ut-off seal
C
1
ilicone Profile 0,669 x 0,315 inch 0320203 8,66 inch (length silicone holder)
S
ID GASKET
L
ODELS
M
VS 20
M
engths specified are always a little longer and must be cut to the correct length.
L
Type
G 22
V
Minipack
Reference
439501
0
SPECIFICATIONS
,76 inch Teflon tape
2
x 0,035 inch round wire
1
x 0,197 inch flat wire
Minipack
REFERENCE
Litres Type
.05
0
0-60Hz
5
LENGTHS (in mm)
320216 43,3 inch
0
Minipack
Reference
939160
0
Minipack
REFERENCE
305556
0
305014
0
305020
0
amount
0,8 inch (length sealing bar + 2,2 inch)
1
1
QUANTITY
4,6 inch
1
4,7 inch
1
ersion 01.10 VMS 20.EN 22
V
SER MANUAL MVS 20
U
TECHNICAL SPECIFICATIONS
ODEL VACUUM
M
CHAMBER
VS 20 Stainless-steel Transparent Stainless-steel 19,7 x 11 x 10 004 99,80%
M
pecifications may deviate with optional models
S
Standard ambient temperature 41 0 F – 86 0 F
For deviating ambient temperatures see page 16 for special oil specifications
Maximum use per day 5 hours
Electricity Voltage : see machine tag
Frequency : see machine tag
Power : see machine tag
Electrical connection Maximum fluctuation ± 10% of the official registered voltage
Sound level < 70 DB
LID HOUSING DIMENSIONS
(length x width x height)
inch)
(
PUMP
(m3/h)
FINAL
VACUUM
(%)
ersion 01.10 VMS 20.EN 23
V
SER MANUAL MVS 20
U
LECTRICAL DIAGRAMS
E
ontrol Current Diagram
C
ain Power Diagram
M
ersion 01.10 VMS 20.EN 24
V
SER MANUAL MVS 20
U
.
List of fuses
uses have been placed where the power comes onto the component board
F
Fuses have been placed on transformers (control and seal)
Two fuses have been placed on the control circuit.
Due to different mains voltages and machine models there is a variety of fuse types that can be present in the machine.
Refer to the specifications of the relevant component for the correct types and values of fuses for replacement, or
contact the supplier or Minipack-america LLC.
Caution, to avoid fire and/or other irreparable damage to the machine, replacement fuses must
always be of the same type with the same value as the fuses being replaced !!
Spanning
aution, the maximum allowable voltage fluctuation is ± 10% of the official voltage stated on the
C
type tag.
ERROR CODES
he control is programmed with an error code. This error code indicates there is a problem with the proper function of
T
the lid switch of there is a user fault.
F1: This code indicates that the cycle (lid switch) will be interrupted prematurely.
Example: the cover of the machine closes after starting, but before sufficient vacuum is present to keep the cover closed
the operator lets go of the cover. The F1 code will now be shown on the display.
If this keeps happening please contact the supplier or your dealer
ersion 01.10 VMS 20.EN 25
V
SER MANUAL MVS 20
U
NEUMATIC DIAGRAM
P
ersion 01.10 VMS 20.EN 26
V
SER MANUAL MVS 20
U
PROBLEM SOLVING
ROBLEM
P
achine does not work
M
achine does not work
M
Operating panel is on
ransparent lid does
T
not open automatically
inal vacuum is
F
insufficient
he machine builds up
T
a vacuum slowly
CAUSE
• The plug is not plugged into the wall
socket.
• The main fuse is burnt.
• The ON/OFF switch’s contact block has
come loose.
• The circuit board fuse is burnt.
• The control transformer fuse is burnt.
• The micro-switch that is activated when
the lid is closed is disordered or faulty.
• There is an internal malfunction.
• The gas spring is faulty
• The set vacuum time is too short.
• There is too little oil in the vacuum
pump.
• The extraction hole at the back of the
vacuum chamber is partially covered by
the vacuum bag during extraction
• The lid gasket is worn.
• The oil is contaminated
• The oil exhaust filter is saturated.
• The pump’s extraction filter is blocked.
• The oil exhaust filter is saturated.
SOLUTION
• Plug the plug into the wall socket.
• Replace the fuse (Ensure the correct
value).
• Check this and if necessary re-fasten it.
• Disassemble the front panel and replace
the fuse.
• Check this and if necessary replace it.
• The micro-switch must be properly
adjusted or replaced
• Consult the supplier.
• Consult the supplier.
• Extend the vacuum time.
• Check the oil level and top up if
necessary (Note the type and quantity).
• Place the vacuum bag closer to the
sealing beam.
• Replace the lid gasket.
• Replace the oil (Note the type & amount).
eplace the oil exhaust filter / Consult
• R
the supplier.
.
• Consult the supplier.
• Replace the oil exhaust filter / Consult
the supplier.
ersion 01.10 VMS 20.EN 27
V
SER MANUAL MVS 20
U
PROBLEM
he vacuum bag is
T
not properly and/or
correctly sealed.
• The vacuum bag is being placed
incorrect on the sealing bar.
• The sealing time is too long or too short.
• The silicone rubber in the silicone holder
is damaged or worn.
• The Teflon tape is damaged.
• The inside of the vacuum bag opening is
contaminated or greased.
CAUSE
SOLUTION
• Place the vacuum bag neatly and
smoothly on the sealing bar. Ensure that
the opening of the bag is always within
the vacuum chamber.
• Adjust the sealing time longer or shorter.
• Replace the silicone rubber.
• Replace the Teflon tape
• Clean the vacuum bag’s opening.
n the case of other problems or questions contact the supplier or Minipack-america LLC.
I
ersion 01.10 VMS 20.EN 28
V
SER MANUAL MVS 20
U
REMARKS ON SPECIAL APPLICATIONS
ACKAGING LIQUID PRODUCTS
P
The machines can be also used for packaging liquid products like soups or sauces. During this process the vacuum
process must be carefully monitored through the lid. The [STOP VACUUM] key must be pressed as soon as bubbles
appear in the product; the saturation point (same as boiling point) has then been reached.
The saturation point of liquids is reached at a certain ratio of low pressures and high temperatures (see the example
table for water below). The saturation point will be reached sooner in the vacuum process when packaging liquids with a
high temperature (the amount of vacuum will therefore be less).
Henkelman recommends therefore to first cool liquid products before packaging. By so doing an optimal vacuum can be
achieved for the product.
Saturation point of water – relation between the pressure and temperature of the water
Vacuum pressure [mbar] 1000 800 600 400 200 100 50 20 10 5 2
oiling Point
B
Temperature [° F]
212 201 187 169 140 113 91
64
44 28 8,6
A handy tip when packaging liquid products is to use a liquid insert plate so that the product remains at the bottom of the
packaging during the vacuuming process and there is less risk of liquid splashing out of the packaging. Contact the
supplier or Minipack-america LLC for more information about the liquid insert plate.
ersion 01.10 VMS 20.EN 29
V
SER MANUAL MVS 20
U
IXATION FRONT PANEL
F
he housing has three holes
T
where the front panel holder
is positioned.
The panel holder has three
pins that corresponds with
these holes.
To fixate the panel holder
there are two click fingers on
each side, these fingers will
snap behind the housing and
fixate the panel holder into
the housing.
Position the panel holder
exactly in line with the three
holes in the housing.
Now push the panel holder
towards the housing.
Now push the side wall of
the panel holder a little
together, while doing this
push the panel holder into
the housing.
o Remove the panel holder from
T
the housing, press both side walls of
the panel holders an pull the
complete front panel holder out of
the housing.
ersion 01.10 VMS 20.EN 30
V
Loading...