MINI Convertible 2015, Coupe Roadster Convertible 2015 Owner's Manual

Download

Page 1

OWNER'S MANUAL.

MINI COUPE.

MINI ROADSTER.

MINI CONVERTIBLE.

Contents

A-Z

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 2

Page 3

COOPER

COOPER S

JOHN COOPER

WORKS

Owner's Manual for Vehicle

Thank you for choosing a MINI.

The more familiar you are with your vehicle, the better control you will have on the road. We therefore strongly suggest:

Read this Owner's Manual before starting off in your new MINI. It contains important information on vehicle operation that will help you make full use of the technical features available in your MINI. The manual also contains information designed to en‐ hance operating reliability and road safety, and to contribute to maintaining the value of your MINI.

Supplementary information can be found in the additional bro‐ chures in the onboard literature.

Set off now and have fun with your MINI.

The MINI Team of BMW AG

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 4

© 2015 Bayerische Motoren Werke Aktiengesellschaft Munich, Germany Reprinting, including excerpts, only with the written consent of BMW AG, Munich. US English II/15, 03 15 500 Printed on environmentally friendly paper, bleached without chlorine, suitable for recycling.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 5

ADDENDUM TO OWNER'S MANUAL

Addendum

We wanted to provide you with some updates and clarifications with respect to the printed MINI Owner's Manual. These updates and clarifications will supersede the materials contained in that document.

1. Where the terms “service center,” “the ser-

vice center,” “your service center,” “service specialist,” or “service” are used in the Owner's Manual, we wanted to clarify that the terms refer to a MINI dealer's service center or another service center or repair shop that employs trained personnel that can perform maintenance and repair work on your vehicle in accordance with MINI specifications.

2. Where the text of the Owner's Manual con-

tains an affirmative instruction to contact a “service center” or “your service center,” we wanted to clarify that MINI recommends that, if you are faced with one of the situations addressed by that text, you contact or seek the assistance of a MINI dealer's service center or another service center or repair shop that employs trained personnel that can perform maintenance and repair work on your vehicle in accordance with MINI specifications.

While MINI, at no cost to you, will pay for repairs required by the limited warranties provided with respect to your vehicle and for maintenance under the Maintenance Program during the applicable warranty and maintenance coverage periods, you are free to elect, both during those periods and thereafter, to have maintenance and repair work provided by other service centers or repair shops.

3. Where the Owner's Manual makes reference

to parts and accessories having been approved by MINI, those references are intended to reflect that those parts and accessories are recommended by MINI. You may elect to use other parts and accessories, but, if you do, we recommend that you make sure

that any such parts and/or accessories are appropriate for use on your vehicle.

4. At page 6 and page 7, under the warranty

section's discussion of homologation, where it states that you “cannot lodge warranty claims for your vehicle there,” the text should read that you “may not be able to lodge warranty claims for your vehicle there.”

5. At page 7, in the “Parts and accessories” sec-

tion, the sentence beginning “For your own safety, … ,” should be disregarded and the following the text should be read in lieu thereof: “The manufacturer of your vehicle recommends using genuine MINI parts and accessories.” In the fifth sentence of that paragraph, the word “cannot” should read “does not.”

6. At page 56, in the “Checking and replacing

safety belts” section, the text beginning, “Have the work performed only by your service center …” should be disregarded and the following text should be read in lieu thereof: “MINI recommends having this work performed by a service center as it is important that this safety feature functions properly.”

7. At page 92, in the “MINI Convertible: Rollo-

ver Protection System” section, the sentence beginning, “Work on the rollover protection system …” should be disregarded and the following text should be read in lieu thereof: “MINI recommends having this work performed by a service center as it is important that this safety feature functions properly.”

8. At page 126 under the heading: “Objects in

the area around the pedals” and at page 262 under the heading: “Carpets/floor mats,” the paragraph that begins: “Only use floor mats …” should be disregarded and the following language should be read in lieu thereof: “The manufacturer of your vehicle recommends that you use floor mats

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 6

Addendum

that have been identified by it as appropriate for use in your vehicle and that can be properly fixed in place.”

9. At page 132, under the heading: “Have

maintenance carried out,” the sentence beginning, “Have the maintenance carried out …” should be disregarded and the following text should be read in lieu thereof: “MINI recommends that you have the maintenance carried out by your service center.”

10. At page 211, under the heading “Software

applications,” the text of that section should be disregarded and the following text read in lieu thereof: “The manufacturer of your vehicle recommends the use of MINI recommended software; otherwise there may be malfunctions in system operations.”

11. At page 220, under the heading “Pressure

specifications,” the sentence beginning, “The inflation pressures apply to the tire sizes approved … .” should be disregarded.

12. At page 229, under the heading: “Approved

wheels and tires,” the term “Approved” should be disregarded and in lieu thereof, the term “Recommended” should be read in its place. In addition, the text of that section should be disregarded and the following text should be read in lieu thereof:

The manufacturer of your vehicle strongly suggests that you use wheels and tires that have been recommended by the vehicle manufacturer for your vehicle type; otherwise, for example, despite having the same official size ratings, variations can lead to body contact and with it, the risk of severe accidents.

The manufacturer of your vehicle does not evaluate non-recommended wheels and tires to determine if they are suitable for use on your vehicle.

13. At page 235, under the heading “Hood,” the

sentence beginning, “If you are unfamiliar” should be disregarded.

14. At page 239, under the heading: “Service

and Warranty Information Booklet for US Models and Warranty and Service Guide Booklet for Canadian Models,” the second paragraph should be disregarded and the following text read in lieu thereof:

The manufacturer of your vehicle recommends that you have maintenance and repair performed by your MINI dealer's service center or another service center or repair shop that employs trained personnel that can perform maintenance and repair work on your vehicle in accordance with MINI specifications. The manufacturer of your vehicle recommends that you maintain records of all maintenance and repair work performed on your vehicle.

15. At page 251, under the “Battery replace-

ment” section, the text should be disregarded and in lieu thereof the following text should be read:

Use of recommended vehicle batteries

The manufacturer of your vehicle recommends that you use vehicle batteries that it has tested and recommends for use in your vehicle; otherwise the vehicle could be damaged and systems or functions may not be fully available.

After a battery replacement, the manufacturer of your vehicle recommends that you have the battery registered on your vehicle by a service center to ensure that all comfort functions are fully available, and that any “check control” messages of these comfort functions are no longer displayed.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 7

Contents

The fastest way to find information on a partic‐ ular topic or item is by using the index, refer to page 276.

6 Notes

AT A GLANCE

12 Cockpit 18 Onboard monitor 24 Voice activation system

CONTROLS

30 Opening and closing 53 Adjusting 59 Transporting children safely 64 Driving 73 Displays 84 Lamps 89 Safety 100 Driving stability control systems 105 Driving comfort 108 Climate 114 Interior equipment 118 Storage compartments

DRIVING TIPS

124 Things to remember when driving 128 Loading 131 Saving fuel

ENTERTAINMENT

158 Tone 160 Radio 168 CD/multimedia

COMMUNICATION

182 Bluetooth hands-free system 192 Bluetooth mobile phone preparation

package

203 Office 211 MINI Connected

MOBILITY

216 Refueling 218 Fuel 220 Wheels and tires 234 Engine compartment 236 Engine oil 238 Coolant 239 Maintenance 241 Replacing components 253 Breakdown assistance 258 Care

REFERENCE

266 Technical data 270 Short commands for voice activation 276 Everything from A to Z

NAVIGATION

136 Navigation system 138 Destination entry 147 Destination guidance 155 What to do if...

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 8

Notes

Using this Owner's Manual

The fastest way to find information on a partic‐ ular topic is by using the index.

An initial overview of the vehicle is provided in the first chapter.

Additional sources of information

Should you have any questions, your service center will be glad to advise you at any time.

Information on MINI, e.g., on technology, is available on the Internet: www.mini.com

Information about MINI, e.g., on technology, is available on the Internet: www.miniusa.com

Symbols

Indicates precautions that must be followed precisely in order to avoid the possibility of personal injury and serious damage to the vehicle.

◄ Marks the end of a specific item of information.

"..." Identifies Control Display texts used to select individual functions.

›...‹ Verbal instructions to use with the voice activation system.

››...‹‹ Identifies the answers generated by the voice activation system.

Refers to measures that can be taken to help protect the environment.

Vehicle equipment

The manufacturer of your MINI is the Bayeri‐ sche Motoren Werke Aktiengesellschaft, BMW AG.

This Owner's Manual describes all models, all series equipment, as well as country-specific and special equipment offered in the model series. Therefore, this Owner's Manual also de‐ scribes and depicts equipment that may not be contained in your vehicle because of the se‐ lected special equipment or country version, for example.

This also applies to safety-related functions and systems.

For options and equipment not described in this Owner's Manual, please refer to the Sup‐ plementary Owner's Manuals.

Status of this Owner's Manual at time of print‐ ing

The manufacturer of your vehicle pursues a policy of constant development that is con‐ ceived to ensure that our vehicles continue to embody the highest quality and safety stan‐ dards. In rare cases, therefore, the features de‐ scribed in this Owner's Manual may differ from those in your vehicle.

For your own safety

Symbols on vehicle components

Indicates that you should consult the relevant section of this Owner's Manual for information on a particular part or assembly.

Online Edition for Part no. 01 40 2 961 056 - II/15

Warranty

Your vehicle is technically configured for the operating conditions and registration require‐ ments applying in the country of first delivery — homologation. If your vehicle is to be oper‐ ated in a different country it might be neces‐

Page 9

Notes

sary to adapt your vehicle to potentially differ‐ ing operating conditions and permit requirements. If your vehicle does not comply with the homologation requirements in a cer‐ tain country you cannot lodge warranty claims for your vehicle there. Further information can be obtained from your Service Center.

Maintenance and repairs

Advanced technology, e.g., the use of modern materials and high-performance electronics, requires suitable maintenance and repair methods.

Therefore, have this work performed only by a MINI service center or a workshop that works according to MINI repair procedures with ap‐ propriately trained personnel.

If this work is not carried out properly, there is the danger of subsequent damage and related safety hazards.

Parts and accessories

For your own safety, it is recommended that you use genuine parts and accessories ap‐ proved by MINI. When you purchase accesso‐ ries tested and approved by MINI and Genuine MINI Parts, you simultaneously acquire the as‐ surance that they have been thoroughly tested by MINI to ensure optimum performance when installed on your vehicle. MINI warrants these parts to be free from defects in material and workmanship. MINI will not accept any liability for damage resulting from installation of parts and accessories not approved by MINI. MINI cannot test every product made by other man‐ ufacturers to verify if it can be used on a MINI safely and without risk to either the vehicle, its operation, or its occupants. Genuine MINI Parts, MINI Accessories and other products approved by MINI, together with professional advice on using these items, are available from all MINI centers. Installation and operation of non MINI approved accessories such as alarms, radios, amplifiers, radar detectors, wheels, suspension components, brake dust shields, telephones,

including operation of any mobile phone from within the vehicle without using an externally mounted antenna, or transceiver equipment, for instance, CBs, walkie-talkies, ham radios or similar accessories, may cause extensive dam‐ age to the vehicle, compromise its safety, inter‐ fere with the vehicle's electrical system or af‐ fect the validity of the MINI Limited Warranty. See your MINI center for additional informa‐ tion. Maintenance, replacement, or repair of the emission control devices and systems may be performed by any automotive repair estab‐ lishment or individual using any certified auto‐ motive part.

California Proposition 65 Warning

California laws require us to state the following warning:

Engine exhaust and a wide variety of automo‐ bile components and parts, including compo‐ nents found in the interior furnishings in a vehi‐ cle, contain or emit chemicals known to the State of California to cause cancer and birth de‐ fects and reproductive harm. In addition, cer‐ tain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other repro‐ ductive harm. Battery posts, terminals and re‐ lated accessories contain lead and lead com‐ pounds. Wash your hands after handling. Used engine oil contains chemicals that have caused cancer in laboratory animals. Always protect your skin by washing thoroughly with soap and water.

Service and warranty

We recommend that you read this publication thoroughly. Your vehicle is covered by the fol‐ lowing warranties:

▷ New Vehicle Limited Warranty.

▷ Rust Perforation Limited Warranty.

▷ Federal Emissions System Defect Warranty.

▷ Federal Emissions Performance Warranty.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 10

Notes

▷ California Emission Control System Limited

Warranty.

Detailed information about these warranties is listed in the Service and Warranty Information Booklet for US models or in the Warranty and Service Guide Booklet for Canadian models.

Your vehicle has been specifically adapted and designed to meet the particular operating con‐ ditions and homologation requirements in your country and continental region in order to de‐ liver the full driving pleasure while the vehicle is operated under those conditions. If you wish to operate your vehicle in another country or re‐ gion, you may be required to adapt your vehi‐ cle to meet different prevailing operating con‐ ditions and homologation requirements. You should also be aware of any applicable war‐ ranty limitations or exclusions for such country or region. In such case, please contact Cus‐ tomer Relations for further information.

Maintenance

Maintain the vehicle regularly to sustain the road safety, operational reliability and the New Vehicle Limited Warranty.

Specifications for required maintenance meas‐ ures:

▷ MINI Maintenance system

▷ Service and Warranty Information Booklet

for US models

▷ Warranty and Service Guide Booklet for

Canadian models

If the vehicle is not maintained according to these specifications, this could result in serious damage to the vehicle. Such damage is not covered by the MINI New Vehicle Limited War‐ ranty.

Data memory

Numerous electronic components in your vehi‐ cle contain data memories that store technical information on the vehicle condition, events

and faults, either temporarily or permanently. This technical information generally documents the state of a component, a module, a system or the environment:

▷ Operating conditions of system compo‐

nents, such as filling levels.

▷ Status messages from the vehicle and its in‐

dividual components, such as wheel rpm/ speed, motion delay, transverse accelera‐ tion.

▷ Malfunctions and defects in important sys‐

tem components, such as lights and brakes.

▷ Vehicle responses to special driving situa‐

tions, such as airbag deployment, use of the stability control systems.

▷ Ambient conditions, such as the tempera‐

ture.

These data are of a technical nature only and are used to detect and eliminate faults and to optimize vehicle functions. Travel profiles of routes driven with the vehicle cannot be cre‐ ated from these data. If services are used, for instance in the event of repairs, service proc‐ esses, warranty cases, quality assurance, etc., this technical information can be read out from the event and fault data memories by service personnel, including the manufacturer, using special diagnosis tools. This service personnel can provide you with more information if needed. After troubleshooting, the information in the fault memory is cleared or overwritten continuously.

Situations are conceivable during the use of the vehicle in which these technical data could be‐ come associated with a specific person in com‐ bination with other information, such as an ac‐ cident report, damage to the vehicle, witness accounts, etc., possibly with the involvement of an authorized expert.

Additional functions that are contractually agreed with the customer, such as vehicle lo‐ calization in the event of an emergency, permit the transfer of certain vehicle data out of the vehicle.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 11

Notes

Event Data Recorder EDR

This vehicle is equipped with an event data re‐ corder EDR. The main purpose of an EDR is to record, in certain crash or near crash-like situa‐ tions, such as an air bag deployment or hitting a road obstacle, data that will assist in under‐ standing how a vehicle's systems performed. The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.

The EDR in this vehicle is designed to record such data as:

▷ How various systems in your vehicle were

operating.

▷ Whether or not the driver and passenger

safety belts were fastened.

▷ How far, if at all, the driver was depressing

the accelerator and/or brake pedal.

▷ How fast the vehicle was traveling.

These data can help provide a better under‐ standing of the circumstances in which crashes and injuries occur.

EDR data are recorded by your vehicle only if a nontrivial crash situation occurs; no data are re‐ corded by the EDR under normal driving condi‐ tions and no personal data, e.g., name, gender, age, and crash location, are recorded.

However, other parties, such as law enforce‐ ment, could combine the EDR data with the type of personally identifying data routinely ac‐ quired during a crash investigation.

To read data recorded by an EDR, special equipment is required, and access to the vehi‐ cle or the EDR is needed. In addition to the ve‐ hicle manufacturer, other parties, such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR.

Reporting safety defects

For US customers

The following only applies to vehicles owned and operated in the US.

If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration NHTSA, in addition to notifying BMW of North America, LLC, P.O. Box 1227, Westwood, New Jersey 07675-1227, Telephone 1-800-831-1117.

If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.

However, NHTSA cannot become involved in individual problems between you, your dealer, or BMW of North America, LLC.

To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safe‐ rcar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, DC 20590. You can also obtain other information about motor vehicle safety from http://www.safe‐ rcar.gov

For Canadian customers

Canadian customers who wish to report a safety- related defect to Transport Canada, De‐ fect Investigations and Recalls, may telephone the toll-free hotline 1-800-333-0510. You can also obtain other information about motor ve‐ hicle safety from http://www.tc.gc.ca/roadsaf‐ ety.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 12

WATCH ME.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 13

AT A GLANCE

CONTROLS

DRIVING TIPS

NAVIGATION

ENTERTAINMENT

COMMUNICATION

MOBILITY

REFERENCE

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 14

AT A GLANCE

Cockpit

Vehicle equipment

special equipment or the country version. This also applies to safety-related functions and sys‐ tems.

When using the features and systems described here, adhere to local regulations.

All around the steering wheel

1 Setting the exterior mirror, folding it in and

out 57

2 Parking lights 84

Low beams 84

Automatic headlamp con‐ trol 84

Adaptive Light Control 86

Online Edition for Part no. 01 40 2 961 056 - II/15

Turn signal 67

High-beams 67

Headlight flasher 67

Roadside parking lights 85

Computer 74

Page 15

Cockpit

AT A GLANCE

3 MINI Roadster, MINI Convertible: Always

Open Timer 76

4 Tachometer 74

Instrument lighting 87

Trip odometer 73

5 Windshield wipers 67

6 Start/stop the engine and switch

the ignition on/off 64

7 Ignition lock 64

8 Steering wheel buttons, right

Resuming cruise control 106

Storing the speed and accelerat‐ ing or slowing down 106

Activating/deactivating cruise control 105

Steering wheel buttons, left

Volume

Bluetooth hands-free sys‐ tem 182

Bluetooth mobile phone prepara‐ tion package 192

Activate/deactivate the voice acti‐ vation system 24

Microphone on the steering col‐ umn

Change the radio station

Select a music track

Scroll through the redial list

9 Horn, the entire surface

10 Adjust the steering wheel 58

11 Releasing the hood 235

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 16

AT A GLANCE

Displays

Cockpit

1 Tachometer 74

with indicator and warning lights 15

2 Display for

▷ Current speed 73

▷ Indicator/warning lights 15

3 Resetting the trip odometer 73

4 Display for

▷ Steptronic transmission position 70

▷ On-board computer 74

▷ Service requirements 80

▷ Odometer and trip odometer 73

▷ Flat Tire Monitor 92

▷ Tire Pressure Monitor 94

▷ Settings and information 76

▷ Personal Profile settings 31

5 Instrument lighting 87

6 Speedometer with indicator and warning

lights 15

7 Control Display 18

8 Fuel gauge 74

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 17

Cockpit

AT A GLANCE

Indicator/warning lights

The concept

The indicator and warning lights can light up in a variety of combinations and colors in display area 1 or 2.

Several of the lights are checked for proper functioning when the engine is started or the ignition is switched on, and light up briefly.

Text messages

Text messages at the upper edge of the Control Display explain the meaning of the displayed indicator and warning lights.

Supplementary text messages

You can call up more information, e.g., on the cause of a malfunction and on how to respond, via Check Control, refer to page 81.

In urgent cases, this information will be shown as soon as the corresponding light comes on.

Indicator lights without text messages

The following indicator lamps notify you that certain functions are active:

Symbol Function or system

Turn signal, refer to page 67

High-beams/headlight flasher, refer to page 67

Front fog lights, refer to page 86

Rear fog light, refer to page 87

DSC or DTC is regulating the propul‐ sive forces in order to maintain driv‐ ing stability, refer to page 100

The parking brake is set, refer to page 66

Engine malfunction with adverse ef‐ fect on emissions, refer to page 240

Cruise control, refer to page 105

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 18

AT A GLANCE

Cockpit

All around the center console

1 Hazard warning system

2 Speedometer with Control Display 14

3 Radio 160

CD/multimedia 160

4 Air conditioning, automatic climate con‐

trol 109

5 Buttons on the center console

Seat heating 55

Power windows 41

Rear fog light 87

MINI Convertible: central power window switch 42

Front fog lights 86

Central locking, inside 35

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 19

Cockpit

AT A GLANCE

All around the head‐ liner

1 Indicator/warning lights for the front pas‐

senger airbags 91

2 Switch panel

Reading lights 87

MINI Roadster: interior lights/ reading lights 87

Ambient lighting color 88

MINI Coupe, MINI Roadster: ex‐ tending and retracting the spoiler manually 102

MINI Convertible: opening and closing the sliding sunroof or convertible top 42

MINI Roadster: opening and clos‐ ing the convertible top 50

Interior lights 87

All around the shift/ selector lever

1 USB audio interface 172

2 Buttons in the center console

Sport button 102

Driving stability control sys‐ tems 100

3 MINI joystick with buttons 18

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 20

AT A GLANCE

Onboard monitor

Vehicle equipment

This chapter describes all series equipment as well as country-specific and special equipment offered for this model series. Therefore, it also describes equipment that may not be found in your vehicle, for instance due to the selected special equipment or the country version. This also applies to safety-related functions and sys‐ tems.

When using the features and systems described here, adhere to local regulations.

The concept

The onboard monitor combines the functions of a large number of different switches. Thus, these functions can be operated from a central location.

Using the onboard monitor during a trip

To avoid becoming distracted and posing an unnecessary hazard to your vehicle's occu‐ pants and to other road users, never attempt to use the controls or enter information unless traffic and road conditions allow this.◀

Control elements at a glance

Control elements

1 Control Display

2 MINI joystick with buttons

The buttons can be used to open the me‐ nus directly. The MINI joystick can be used to select menu items and create settings.

Control Display

Hints

▷ To clean the Control Display, follow the care

instructions, refer to page 262.

▷ Do not place objects close to the Control

Display; otherwise, the Control Display can be damaged.

Switch off

Move the MINI joystick repeatedly to the

right until the "Options" menu appears.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 21

Onboard monitor

AT A GLANCE

2. "Switch off control display"

Switching on

Press the MINI joystick to switch on.

MINI joystick with buttons

Select menu items and create settings.

Turn, arrow 1.

2. Press, arrow 2.

3. Move in four directions.

Buttons on the MINI joystick

Press button Function

Open the main menu.

Changes to another menu.

Operating concept

Start screen

In the radio ready state and higher, the follow‐ ing message appears on the Control Display:

To hide the message: press the MINI joystick. The main menu is displayed.

The message is automatically hidden after ap‐ prox. 10 seconds.

Opening the main menu

Press the button.

The main menu is displayed.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 22

AT A GLANCE

All onboard monitor functions can be called up via the main menu.

Onboard monitor

Selecting menu items

Menu items shown in white can be selected.

1. Turn the MINI joystick until the desired

menu item is highlighted.

2. Press the MINI joystick.

A new menu is displayed or the function is per‐ formed.

With the button on the MINI joystick:

Press the button.

The menu items of the main menu can be opened consecutively by pressing the button repeatedly.

White arrows pointing to the left or right indi‐ cate that additional panels can be opened.

View of an opened menu

When a menu is opened, it generally opens with the panel that was last selected in that menu. To display the first panel of a menu:

Move the MINI joystick to the left repeatedly until the first panel is displayed.

Opening the Options menu

Move the MINI joystick repeatedly to the right until the "Options" menu appears.

Menu items in the Owner's Manual

In the Owner's Manual, menu items that can be selected are set in quotation marks, e.g., "Settings".

Changing between panels

After a menu item is selected, e.g., "Radio", a new panel is displayed. Panels can overlap.

▷ Move the MINI joystick to the left.

The current panel is closed and the previ‐ ous panel is displayed.

▷ Move the MINI joystick to the right.

A new panel is opened on top of the previ‐ ous display.

Online Edition for Part no. 01 40 2 961 056 - II/15

Options menu

The "Options" menu consists of various areas:

▷ Screen settings, e.g., "Switch off control

display".

▷ Control options for the selected main

menu, e.g., for "Radio".

▷ If applicable, further operating options for

the selected menu, for instance "Store station".

Page 23

Onboard monitor

AT A GLANCE

Changing settings

1. Select a field.

2. Turn the MINI joystick until the desired set‐

ting is displayed.

3. Press the MINI joystick to confirm the set‐

ting.

Activating/deactivating the functions

Several menu items are preceded by a check‐ box. It indicates whether the function is acti‐ vated or deactivated. Selecting the menu item activates or deactivates the function.

Function is activated.

The function is deactivated.

Example: setting the clock

Setting the clock

2. Turn the MINI joystick until "Settings" is

3. If necessary, move the MINI joystick to the

4. Turn the MINI joystick until "Time/Date" is

Press the button. The main menu is

displayed.

highlighted and press the MINI joystick.

left to display "Time/Date".

highlighted and press the MINI joystick.

5. Turn the MINI joystick to set the hours and

press the MINI joystick.

6. Turn the MINI joystick to set the minutes

and press the MINI joystick.

Status information

Status field

The following information is displayed in the status field at the top right:

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 24

AT A GLANCE

Onboard monitor

▷ Time.

▷ Current entertainment source.

▷ Sound output, on/off.

▷ Wireless network reception strength.

▷ Telephone status.

▷ Traffic bulletin reception.

Check Control messages and entries using the voice activation system temporarily hide the status information.

Status field symbols

The symbols are grouped into various catego‐ ries.

Radio symbols

Symbol Meaning

HD Radio™ is switched on.

Satellite radio is switched on.

Telephone symbols

Symbol Meaning

Incoming or outgoing call.

Symbol Meaning

USB audio interface.

Music interface for smartphones.

Additional symbols

Symbol Meaning

Spoken instructions are switched off.

Entering letters and numbers

General information

Turn the MINI joystick: select letters or

numbers.

2. Select additional letters or numbers if

needed.

3. "OK": confirm the entry.

Wireless network reception strength

Symbol flashes: searching for network.

Wireless network is not available.

Bluetooth is switched on.

Roaming is active.

Text message, e-mail was received.

Entertainment symbols

Symbol Meaning

CD player.

AUX-IN port.

Online Edition for Part no. 01 40 2 961 056 - II/15

Symbol Function

Press the MINI joystick: delete the let‐

ter or number.

Press the MINI joystick for an ex‐

tended period: delete all letters or numbers.

Enter a blank space.

Switching between letters and numbers

Depending on the menu, you can switch be‐ tween entering letters and numbers.

Page 25

Onboard monitor

Symbol Function

Enter the letters.

Enter the numbers.

Switching between upper and lower case letters

Depending on the menu, you can switch be‐ tween entering uppercase and lowercase let‐ ters.

Symbol Function

Move the MINI joystick forward:

switch from upper to lower case letters.

Move the MINI joystick forward:

switch from lower to upper case letters.

Entry comparison

Entry of names and addresses: the selection is narrowed down every time a letter is entered and letters may be added automatically.

The entries are continuously compared to the data stored in the vehicle.

▷ Only those letters are offered during the

entry for which data is available.

▷ Destination search: town/city names can be

entered using the spelling of language available on the Control Display.

AT A GLANCE

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 26

AT A GLANCE

Voice activation system

Vehicle equipment

When using the features and systems described here, adhere to local regulations.

The concept

▷ Most functions that are displayed on the

Control Display can be operated with the voice activation system using spoken com‐ mands. The system prompts you to make your entries.

▷ Functions that can only be used when the

vehicle is stationary cannot be operated us‐ ing the voice activation system.

▷ The system uses a special microphone on

the steering column.

▷ ›...‹ Verbal instructions in the Owner's

Manual to use with the voice activation sys‐ tem.

Using voice activation

Activating the voice activation system

2. Wait for the signal.

3. Say the command.

If no other commands are available, operate the function via the onboard monitor in this case.

Terminating the voice activation system

Press the button on the steering

wheel.

This symbol on the Control Display indi‐ cates that the voice activation system is ac‐ tive.

The command appears on the Control Dis‐ play.

Requirements

Via the Control Display, set a language that is also supported by the voice activation system so that the spoken commands can be identi‐ fied.

Set the language, refer to page 79.

Online Edition for Part no. 01 40 2 961 056 - II/15

Briefly press the button on the steering

wheel or ›Cancel‹.

Possible commands

Most menu items on the Control Display can be voiced as commands.

The available commands depend on the menu that is currently displayed on the Control Dis‐ play.

Page 27

Voice activation system

AT A GLANCE

The functions of the main menu have short commands.

Some list items, such as the phone book en‐ tries, can also be selected via the voice activa‐ tion system. Say the list items exactly as they are displayed on the list.

Having possible commands read aloud

You can have the system read possible com‐ mands aloud: ›Voice commands‹.

For example, if the "CD" menu is displayed, the commands for the operating the CD player are read out loud.

Executing functions using short commands

Functions on the main menu can be performed directly by means of short commands, usually irrespective of which menu item is currently se‐ lected, for instance ›Vehicle status‹.

List of short commands of the voice activation system, refer to page 270.

Help dialog for the voice activation system

Calling up help dialog: ›Help‹

Additional commands for the help dialog:

▷ ›Help with examples‹: information about

the current operating options and the most important commands for them are an‐ nounced.

▷ ›Help with voice activation‹: information

about the principle of operation for the voice activation system is announced.

Example: playing back a CD

Via the main menu

The commands of the menu items are spoken out loud, in the same way as they are selected via the MINI joystick.

1. Switch on the Entertainment sound output

if necessary.

3. ›C D and multimedia‹

4. ›C D‹

5. ›C D drive‹

7. ›Track ...‹ e.g., CD track 4.

Via short commands

Playback of the CD can also be started using a short command.

3. ›C D drive Track ...‹ e.g., CD track 4.

Press the button on the steering

wheel.

The medium last played is played back.

The CD is played back.

Press the button on the steering

wheel again to select a specific track.

Switch on the Entertainment sound output if necessary.

Press the button on the steering

wheel.

Setting the voice dialog

You can set whether the system should use the standard dialog or a shorter version.

In the shorter variant of the voice dialog, the announcements from the system are issued in an abbreviated form.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 28

AT A GLANCE

Voice activation system

On the Control Display:

1. "Settings"

2. "Language/Units"

3. "Speech mode:"

4. Select the setting.

Adjusting the volume

Turn the volume button during the spoken in‐ structions until the desired volume is set.

▷ The volume remains constant even if the

volume of other audio sources is changed.

▷ The volume is stored for the remote control

currently in use.

▷ Always say commands in the language of

the voice activation system.

▷ Keep the doors and windows closed to pre‐

vent noise interference.

▷ Avoid making other noise in the vehicle

while speaking.

Notes on Emergency Re‐ quests

Do not use the voice activation system to ini‐ tiate an Emergency Request. In stressful situa‐ tions, the voice and vocal pitch can change. This can unnecessarily delay the establishment of a telephone connection.

Environmental condi‐ tions

▷ Say the commands, numbers, and letters

smoothly and with normal volume, empha‐ sis, and speed.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 29

Voice activation system

AT A GLANCE

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 30

HANDLE ME.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 31

AT A GLANCE

CONTROLS

DRIVING TIPS

NAVIGATION

ENTERTAINMENT

COMMUNICATION

MOBILITY

REFERENCE

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 32

CONTROLS

Opening and closing

Vehicle equipment

When using the features and systems described here, adhere to local regulations.

Remote control/key

Buttons on the remote control

1 Opening tailgate

2 Unlocking

3 Locking

General information

Each remote control contains a rechargeable battery that is automatically recharged when it is in the ignition lock while the car is being driven. Use each remote control at least twice a year for longer road trips in order to maintain the batteries' charge status.

In vehicles equipped with Comfort Access, the remote control contains a replaceable battery, refer to page 39.

The settings called up and implemented when the vehicle is unlocked depend on which re‐ mote control is used to unlock the vehicle, Per‐ sonal Profile, refer to page 31.

In addition, information about service require‐ ments is stored in the remote control, Service data in the remote control, refer to page 239.

Integrated key

Press button 1 to unlock the key.

The integrated key fits the following locks:

▷ Driver's door, refer to page 34.

▷ MINI Convertible, MINI Roadster: glove

compartment, refer to page 118.

▷ MINI Convertible: lock of rear seat backrest,

refer to page 116.

▷ MINI Coupe, MINI Roadster: through-load‐

ing opening, refer to page 117.

New remote controls

You can obtain new remote controls from your service center.

Loss of the remote controls

Lost remote controls can be blocked by your service center.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 33

Opening and closing

CONTROLS

Personal Profile

The concept

You can set several of your vehicle's functions to suit your personal needs and preferences.

▷ Through Personal Profile, most of these set‐

tings are stored for the remote control cur‐ rently in use.

▷ While the vehicle is being unlocked, the re‐

mote control is recognized and the settings stored with it are called up and imple‐ mented.

▷ Your personal settings will be recognized

and called up again even if the vehicle has been used in the meantime by someone else with another remote control.

▷ The individual settings are stored for no

more than three remote controls.

Personal Profile settings

The following functions and settings can be stored in a profile.

More information on the settings can be found under:

▷ Response of the central locking system

when the car is being unlocked, refer to page 32.

▷ Automatic locking of the vehicle, refer to

page 35.

▷ Triple turn signal activation, refer to

page 67.

▷ Settings for the displays on the onboard

monitor, in the speedometer, and in the tachometer:

▷ 12h/24h clock format, refer to

page 78.

▷ Date format, refer to page 79.

▷ Brightness of the Control Display, refer

to page 79.

▷ Language on the Control Display, refer

to page 79.

▷ Units of measure for fuel consumption,

distance covered/remaining distances, and temperature, refer to page 77.

▷ Light settings:

▷ Headlamp courtesy delay feature, refer

to page 85.

▷ Daytime running lights, refer to

page 85.

▷ Automatic climate control, refer to

page 110: AUTO program, activating/deac‐ tivating the cooling function, setting the temperature, air volume, and air distribu‐ tion.

▷ Entertainment:

▷ Tone settings, refer to page 158.

▷ Volume, refer to page 158.

Central locking system

The concept

The central locking system becomes active when the driver's door is closed.

The system simultaneously engages and re‐ leases the locks on the following:

▷ Doors.

▷ Tailgate.

▷ Fuel filler flap.

Operating from the outside

▷ Via the remote control.

▷ Via the door lock.

▷ In cars with Comfort Access, via the door

handles on the driver's and front passenger sides.

The following takes place simultaneously when locking/unlocking the vehicle via the remote control:

▷ Depending on the vehicle equipment, the

anti-theft protection is switched on and off as well. The anti-theft protection makes it

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 34

CONTROLS

Opening and closing

impossible to unlock the doors using the lock buttons or door handles.

▷ The welcome lamps, interior lamps, and

ambient lighting are switched on and off.

▷ The alarm system is armed or disarmed, re‐

fer to page 39.

Operating from the inside

Via the button for the central locking system, refer to page 35.

In an accident of the necessary severity, the central locking system unlocks automatically.

The hazard warning system and interior lamps come on.

Opening and closing: from the outside

Using the remote control

General information

Take the remote control with you

People or animals left unattended in a parked vehicle can lock the doors from the in‐ side. Always take the remote control with you when leaving the vehicle so that the vehicle can then be opened from the outside.◀

Unlocking

Press the button. The vehicle is un‐

locked.

The welcome lamps and interior lamps are switched on.

You can set how the vehicle is to be unlocked.

The setting is stored for the remote control cur‐ rently in use.

1. "Settings"

2. "Door locks"

3. "Unlock button"

4. Select the desired function:

▷ "All doors"

Press the button once: the en‐

tire vehicle unlocks.

▷ "Driver's door only"

Pressing the button once un‐ locks only the driver's door and the fuel filler flap. Pressing twice unlocks the entire vehicle.

Convenient opening

Press and hold the button on the re‐

mote control.

The power windows are opened. In the MINI Convertible, the sliding sunroof is opened as well.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 35

Opening and closing

CONTROLS

To open the convertible top and the rear win‐ dows in the MINI Convertible: release the but‐ ton and then press and hold it again until the convertible top is fully open. The side windows remain open.

MINI Convertible with Comfort Access:

Hold the button down.

When you are close to the vehicle, the side win‐ dows move up after the convertible top is opened.

Convenient closing

MINI Convertible:

The convertible top, sliding sunroof, and win‐ dows can be closed using the remote control for Comfort Access when you are close to the vehicle.

Hold the button down.

The convertible top and windows are closed.

Monitor the closing process

Watch during the closing process to be sure that no one is injured. Removing the hand from the door handle immediately stops the closing process.◀

MINI Coupe, MINI Roadster:

Convenient closing with the remote control is not possible.

Locking

Press the button.

Locking from the outside

Do not lock the vehicle from the outside if there are people in it, as the vehicle cannot be unlocked from inside without special knowl‐ edge.◀

Setting the confirmation signals

Have unlocking or locking of the vehicle con‐ firmed.

1. "Settings"

2. "Door locks"

3. "Flash when lock/unlock"

4. Press the MINI joystick.

Switching on the interior lamps

When the vehicle is locked:

Press the button.

You can also use this function to locate your ve‐ hicle in parking garages, etc.

Unlocking the tailgate

Press the button for approx. 1 second

and then release it.

Malfunctions

The function of the remote control may be im‐ paired by local radio waves. If this occurs, un‐ lock and lock the vehicle at the door lock with the integrated key.

If it should become impossible to lock the vehi‐ cle with a remote control, the battery in the re‐ mote control is discharged. Use this remote control on an extended trip to recharge the battery, refer to page 30.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 36

CONTROLS

Opening and closing

For US owners only

The transmitter and receiver units comply with part 15 of the FCC/Federal Communication Commission regulations. Operation is governed by the following:

FCC ID:

LX8766S

LX8766E

LX8CAS

Compliance statement:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

▷ This device may not cause harmful interfer‐

ence, and

▷ this device must accept any interference re‐

ceived, including interference that may cause undesired operation.

Any unauthorized modifications or changes to these devices could void the user's authority to operate this equipment.

Using the door lock

Locking from the outside

Do not lock the vehicle from the outside if there are people in it, as the vehicle cannot be unlocked from inside without special knowl‐ edge.◀

Unlocking the doors and tailgate at once

To lock all doors, the fuel filler flap, and the tail‐ gate at once:

1. With the doors closed, lock the vehicle us‐

ing the button for the central locking sys‐ tem in the interior, refer to page 35.

2. Unlock and open the driver's or front pas‐

senger door, refer to page 35.

3. To lock the vehicle:

▷ Lock the driver's door using the

integrated key in the door lock, or

▷ Press down the lock button of the front

passenger door and close the door from the outside.

Convenient opening and closing

In vehicles with an alarm system or Comfort Ac‐ cess, the windows can be operated via the door lock.

MINI Convertible: sliding sunroof and convertible top operation in addition.

Sets how the vehicle is to be unlocked, refer to page 32.

In some vehicle equipment versions, only the driver's door can be unlocked and locked via the door lock.

Online Edition for Part no. 01 40 2 961 056 - II/15

Opening/closing

Turn the key to the unlock or lock position and hold it there.

In the MINI Convertible, the convertible top is closed, followed by the sliding sunroof and side windows.

Keep the closing area clear

Watch during the opening and closing process to be sure that no one becomes trap‐ ped. Releasing the key stops the motion.◀

Page 37

Opening and closing

CONTROLS

Manual operation

If an electrical malfunction occurs, the driver's door can be unlocked or locked by turning the integrated key to the end positions of the door lock.

Opening and closing: from the inside

The switch can be used to lock or unlock the doors and tailgate when the doors are closed, but they are not theft-protected. The fuel filler flap remains unlocked.

Unlocking and opening doors

▷ Using the switch for the central locking sys‐

tem, unlock all of the doors at once and then pull the door opener above the arm‐ rest, or

▷ Pull the door handle on each door twice:

the door is unlocked the first time and opened the second time.

Locking

▷ Press the switch or

▷ Push down the lock button of a door. To

avoid locking yourself out by accident, the driver's door cannot be locked at the lock button while the door is open.

Automatic locking

In addition, it is possible to set the situations in which the vehicle locks. The setting is stored for the remote control in use.

1. "Settings"

2. "Door locks"

3. Select a menu item:

▷ "Lock if no door is opened"

The central locking system locks after a short period if no door is opened.

▷ "Lock after start. to drive"

The central locking system locks when you start driving.

Take the remote control with you

Tailgate

Opening

The tailgate pivots back and up when it opens. Ensure that adequate clearance is available be‐ fore opening.

Provide edge protection

Sharp or angular objects can hit the rear window while driving and damage the heating wires of the rear window. Provide edge protec‐ tion.◀

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 38

CONTROLS

In some market-specific versions, the tailgate can only be unlocked using the remote control if the vehicle was unlocked first.

Press and hold the button on the re‐ mote control or the button in the handle, ar‐ row. The tailgate is unlocked and can be opened.

Opening and closing

MINI Convertible

Pull the handle. The tailgate is unlocked.

MINI Convertible:

1. Using the integrated key, unlock the lock of

the rear seat backrests 1

The open tailgate can be loaded with a maxi‐ mum weight of 175 lbs/80 kg.

Manual release

In the event of an electrical malfunction, the tailgate can be unlocked manually.

MINI Coupe, MINI Roadster:

Online Edition for Part no. 01 40 2 961 056 - II/15

2. Press button 2 and fold the rear seat back‐

rest forward while guiding the safety belt.

3. Pull the handle, see arrow. The tailgate is

unlocked.

Page 39

Opening and closing

CONTROLS

MINI Convertible, MINI Roadster: emergency unlocking

Pull the handle in the cargo area. The tailgate is unlocked.

Closing

Keep the closing area clear

Make sure that the closing area of the tailgate is clear; otherwise, injuries or damage may result.◀

Take the remote control with you

Always take the remote control with you when leaving the vehicle and do not place it in the cargo area; otherwise, the remote control may be locked into the vehicle when the tail‐ gate is closed.◀

MINI Coupe

MINI Roadster

Recessed grips on the inside trim of the tailgate can be used to conveniently pull down the tail‐ gate.

Comfort Access

The concept

The vehicle can be accessed without activating the remote control. All you need to do is to have the remote control with you, e.g., in your jacket pocket. The vehicle automatically de‐ tects the remote control when it is nearby or in the passenger compartment.

Comfort Access supports the following func‐ tions:

▷ Unlocking/locking of the vehicle.

▷ Unlocking of the tailgate separately.

▷ Starting the engine.

▷ MINI Convertible: Convenient closing and

convertible top operation with the remote control for Comfort Access.

▷ MINI Coupe, MINI Roadster: closing the side

windows.

Recessed grips on the inside trim of the tailgate can be used to conveniently pull down the tail‐ gate.

Online Edition for Part no. 01 40 2 961 056 - II/15

Functional requirements

▷ There are no external sources of interfer‐

ence in the vicinity.

▷ To lock the vehicle, the remote control

must be located outside of the vehicle.

▷ The next unlocking and locking cycle is not

possible until after approx. 2 seconds.

Page 40

CONTROLS

Opening and closing

▷ The engine can only be started if the re‐

mote control is inside the vehicle.

▷ The doors and tailgate must be closed to

operate the windows.

Comparison with ordinary remote control

The functions can be controlled by pressing the buttons or via Comfort Access.

Notes on opening and closing, refer to page 30.

If you notice a brief delay while opening or closing the windows or convertible top, the sys‐ tem is checking whether a remote control is in‐ side the vehicle. Repeat the opening or closing procedure, if necessary.

Unlocking

opened and closed when a remote control is lo‐ cated inside the vehicle.

Unlocking the tailgate separately

Press the button on the exterior of the tailgate.

This corresponds to pressing the following but‐

ton on the remote control:

If a remote control accidentally left in the cargo area is detected in the locked vehicle after the tailgate is closed, the tailgate opens again slightly. The hazard warning system flashes and an acoustic signal sounds.

Power windows

When the engine is switched off, the windows can be operated as long as neither the doors nor the tailgate are opened.

When the door and tailgate are closed again and the remote control is detected inside the vehicle, the windows can be operated again.

Insert the remote control into the ignition lock to be able to operate the windows while the engine is switched off and the doors are open.

Press button 1.

Depending on the setting, either only the driv‐ er's door or the entire vehicle is unlocked, refer to page 32.

Pressing the button again locks the entire vehi‐ cle again.

Convenient opening with the remote control, refer to page 32.

Locking

Press button 1.

MINI Convertible, MINI Roadster: windows and convertible top operation

In the radio ready state and beyond, the win‐ dows and the electrical convertible top can be

Online Edition for Part no. 01 40 2 961 056 - II/15

Switching on the radio ready state

Press the Start/Stop button to switch on the radio ready state, refer to page 64.

Do not depress the brake or the clutch; other‐ wise, the engine will start.

Starting the engine

The engine can be started or the ignition can be switched on, refer to page 64, when a re‐ mote control is inside the vehicle. It is not nec‐ essary to insert a remote control into the igni‐ tion lock.

Switching off the engine in cars with Steptronic transmission

The engine can only be switched off with the selector lever in position P, refer to page 70.

Page 41

Opening and closing

CONTROLS

To switch off the engine with the selector lever in position N, the remote control must be in‐ serted in the ignition lock.

Before driving a vehicle with Steptronic transmission into a car wash

1. Insert the remote control into the ignition

switch.

2. Depress the brake pedal.

3. Move the selector lever to position N.

4. Switch the engine off.

The vehicle can roll.

Malfunction

The Comfort Access functions can be disturbed by local radio waves, such as by a mobile phone in the immediate vicinity of the remote control or when a mobile phone is being charged in the vehicle.

If this occurs, open or close the vehicle using the buttons on the remote control or use the integrated key in the door lock.

To start the engine afterward, insert the remote control into the ignition switch.

The indicator lamp lights up and a mes‐ sage appears on the Control Display: re‐ place the remote control battery.

Replacing the battery

The remote control for Comfort Access contains a battery that will need to be replaced from time to time.

1. Remove the cover.

2. Insert a new battery with the positive side

facing upwards.

3. Press the cover closed.

Return used battery to a recycling center or to your service center.

Warning lights

The warning light in the instrument cluster lights up when you attempt to start the engine: the engine cannot be

started.

The remote control is not in the vehicle or has a malfunction. Take the remote control with you inside the vehicle or have it checked. If neces‐ sary, insert another remote control into the ig‐ nition switch.

The warning lamp in the instrument cluster lights up while the engine is run‐ ning: the remote control is no longer in‐

side the vehicle.

After switching off the engine, the engine can only be started again within approx. 10 sec‐ onds if no door has been opened.

Online Edition for Part no. 01 40 2 961 056 - II/15

Alarm system

The concept

The enabled alarm system reacts to the follow‐ ing:

▷ Opening of a door, the hood or the tailgate.

▷ Movements inside the vehicle.

▷ Changes in the vehicle tilt, e.g., during at‐

tempts to steal a wheel or tow the car.

▷ Interruptions in battery voltage.

Depending on the market-specific version, the alarm system briefly signals unauthorized entry attempts by:

▷ By sounding an acoustic alarm.

▷ By switching on the hazard warning system.

Page 42

CONTROLS

Opening and closing

Arming and disarming the alarm system

General information

When the vehicle is locked and unlocked, the alarm system is armed and disarmed at the same time.

Door lock and armed alarm system

Unlocking via the door lock will trigger the alarm on some market-specific versions.

To stop this alarm, unlock the vehicle with the remote control or switch on the ignition.

Tailgate with armed alarm system

The tailgate, refer to page 33, can also be opened when the alarm system is armed.

Press the button on the remote con‐

trol.

When you subsequently close the tailgate, it is again locked and monitored.

Unlocking via the door lock will trigger the alarm on some market-specific versions.

Switching off the alarm

▷ Unlock the vehicle using the remote con‐

trol, refer to page 32.

▷ Insert the remote control all the way into

the ignition lock.

▷ With Comfort Access and if you are carrying

the remote control with you, push the but‐ ton on the door lock.

Display on the tachometer

When the alarm system is being armed, all LEDs pulse like a heartbeat. One LED flashes after approx. 16 minutes.

▷ LEDs pulse or LED flashes: system is armed.

▷ One LED flashes at short intervals: the

doors, hood, or tailgate is not properly closed.

Even if these are not closed fully, the re‐ maining items are locked and the LEDs pulse after approx. 10 seconds for approx. 16 minutes; afterwards, one LED flashes. The interior motion sensor is not activated.

▷ The LEDs go out after the vehicle is un‐

locked: the vehicle has not been tampered with in the meantime.

▷ The LEDs flash after the vehicle is unlocked

until the remote control is inserted in the ignition, but for no longer than approx. 5 minutes: the vehicle has been tampered with in the meantime.

Panic mode

You can trigger the alarm system if you find yourself in a dangerous situation.

Press the button on the remote control

for at least two seconds.

To switch off the alarm: press any button on the remote control.

Tilt alarm sensor

The tilt of the vehicle is monitored.

The alarm system responds in situations such as attempts to steal a wheel or tow the car.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 43

Opening and closing

CONTROLS

Interior motion sensor

MINI Coupe

For the interior motion sensor to function prop‐ erly, the windows must be closed.

MINI Convertible, MINI Roadster

The interior of the car is monitored up to the height of the seat cushions. Thus the alarm sys‐ tem is armed together with the interior motion sensor even if the convertible top is open. An alarm can be triggered unintentionally by fall‐ ing objects such as leaves, refer to Avoiding un‐ intentional alarms.

Avoiding unintentional alarms

The tilt alarm sensor and interior motion sensor can be switched off together, such as in the fol‐ lowing situations:

▷ In duplex garages.

▷ During transport on car-carrying trains, at

sea or on a trailer.

▷ When animals are to remain in the vehicle.

Switching off the tilt alarm sensor and interior motion sensor

▷

▷ Lock the vehicle twice with the integrated

The LEDs flash in short succession for approx. 2 seconds. The tilt alarm sensor and interior motion sensor remain switched off until the ve‐ hicle is unlocked and locked again.

Press the button on the remote

control twice in succession.

key.

Power windows

General information

Take the remote control with you

Take the remote control with you when leaving the vehicle so that children, for exam‐ ple, cannot operate the power windows and in‐ jure themselves.◀

If, after having been opened and closed a num‐ ber of times in close succession, a window can only be closed, the system is overheated. Let the system cool down for several minutes with the ignition switched on or the engine running.

Opening

▷ Press the switch downward.

The window opens until the switch is re‐ leased.

▷ Press the switch downward briefly.

In the radio ready state and higher, the window opens automatically. Press again briefly to stop the opening procedure.

To open the window by a crack, briefly press the switch downward twice in close succession.

Closing

Danger of pinching

Monitor the closing process and make sure that the closing path of the window is clear; otherwise, injuries may result.◀

To close, press the switch upward. The window closes until the switch is released.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 44

CONTROLS

Opening and closing

Initializing the power windows

If the battery was disconnected, for example to change the battery or to put the vehicle into storage, reinitialize the power windows; other‐ wise, the windows will not be lowered.

1. Close the doors.

2. Open both windows.

3. Close both windows.

Please contact your service center in the event of a malfunction.

MINI Convertible: central power windows switch

▷ Press the switch downward.

The rear and front windows open consecu‐ tively until the switch is released.

▷ Press the switch downward briefly.

With the ignition switched on: the rear and front windows open automatically. Press again briefly to stop the opening proce‐ dure.

To close the windows, press the switch upward and hold it.

Do not close the windows until the closing pro‐ cedure of the convertible top is completed; otherwise, it cannot be ensured that the side windows will form a tight seal with the rubber seals of the convertible top. Convertible top, re‐ fer to page 43.

After the ignition is switched off

The windows can be operated for approx. 1 mi‐ nute after the remote control is removed or the ignition is switched off.

Take the remote control with you

Take the remote control with you when leaving the vehicle so that children, for exam‐ ple, cannot operate the power windows and in‐ jure themselves.◀

MINI Convertible: convertible top with integrated sliding sun‐ roof

If possible, conserve the battery by only operat‐ ing the convertible top while the engine is run‐ ning.

Before closing the convertible top, remove all foreign objects from the windshield frame as these could prevent the top from closing prop‐ erly.

Opening and closing the sliding sunroof

To open:

Press the switch back until the desired position or the end position is reached.

To close:

Press the switch forward.

The sliding sunroof can be opened or closed at vehicle speeds up to 74 mph/120 km/h.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 45

Opening and closing

CONTROLS

Electrical convertible top

The fully-automatic convertible top combines reliable weather protection with simple and convenient operation.

To ensure that you will continue to enjoy your MINI Convertible, here are a few tips:

▷ It is advisable that you close the convertible

top when you park the vehicle. Not only does the closed convertible top protect the vehicle interior against unanticipated weather damage, it also offers a certain amount of theft protection. However, even when the convertible top is closed, valua‐ bles should only be stored in the locked cargo area.

▷ Do not attach roof rack systems to the

convertible top.

▷ If you open the convertible top while it is

wet, e.g., after driving in the rain, water may drip into the cargo area. If necessary, remove items from the cargo area before‐ hand to avoid water stains or soiling.

Safety notes on the convertible top

▷ At temperatures below +10 ℉/-12 ℃,

do not move the convertible top or else damage could result.

▷ Do not leave the convertible top open for

longer than one day while it is wet; other‐ wise, damage could be caused by the mois‐ ture.

▷ Do not place any objects on the convertible

top; otherwise, they could fall during oper‐ ation of the convertible top and cause damage or injury.

▷ The convertible top pivots up when it is

opened and closed. When moving the convertible top in places like garages, en‐ sure that there is a minimum height of 79 inches/2 meters; otherwise, damage could result.

▷ When the rollover protection system is ex‐

tended, do not move the convertible top under any circumstances.

▷ Always carry out the convertible top move‐

ment to the end. Driving when the convertible top is not fully opened or closed may result in damage or injury.

▷ During opening and closing, ensure that

people cannot be injured by the convertible top frame or other moving parts. Keep chil‐ dren away from the opening path of the convertible top.

▷ For safety reasons, only move the

convertible top while the vehicle is station‐ ary, if possible.

▷ Do not place any objects on the convertible

top; otherwise, they could fall during oper‐ ation of the convertible top and cause damage or injury.◀

Before opening and closing

▷ Follow the above-mentioned safety instruc‐

tions.

▷ Ensure that the cargo cover is in the lower

position, refer to page 117; otherwise, the convertible top cannot be opened.

▷ Ensure that cargo does not push against

the cargo cover from underneath.

▷ Ensure that the tailgate is closed.

Opening and closing the convertible top

To open:

Press the switch back to open the sliding sun‐ roof. Press it again to open the convertible top.

To close:

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 46

CONTROLS

Opening and closing

Press the switch forward.

Operation while driving

The convertible top can be opened or closed while driving at vehicle speeds up to approx. 20 mph/30 km/h.

Pay close attention to the traffic

When operating the convertible top while driving, pay extra attention to the traffic to avoid an accident. If possible, do not move the convertible top while driving in reverse because your view to the rear is severely limited during the procedure. Do not operate the convertible top while the vehicle is moving through curves, on uneven road surfaces, or in wind.◀

For better control

▷ The LED lights up while the convertible top

is activated until the top is fully opened or closed.

▷ The LED flashes after the switch is released.

The opening or closing procedure is not yet fully completed. The sequence can be con‐ tinued in the desired direction by pushing or pulling the switch.

▷ The "convertible top not locked" indicator

lamp lights up and a message appears on the Control Display.

Interruption

Danger

A convertible top that is not fully opened or closed is a source of danger.◀

The automatic sequence of movements is inter‐ rupted immediately if the switch for convertible top operation is released. The sequence can be continued in the desired direction by pushing or pulling the switch.

When the opening or closing procedure is inter‐ rupted because the switch is released, the convertible top remains in the position in which it stopped for a few seconds before it slowly

moves to a stable position. The sequence can be continued using the switch.

The opening or closing procedure is also inter‐ rupted when it is blocked mechanically. To be able to reactivate the convertible top in this case:

1. Switch the ignition off and on again.

2. Press the switch to continue the sequence

in the desired direction.

Opening and closing procedure

Do not interrupt the closing procedure

Do not interrupt and resume the closing procedure several times in close succession as this could damage the convertible top mecha‐ nism.◀

If, after having been activated a number of times in close succession, the convertible top can only be moved in one direction, the convertible top system is overheated. Let the system cool for approx. 4 minutes.

If the battery was disconnected, for example to change the battery or to put the vehicle into storage, reinitialize, refer to page 42, the power windows; otherwise, the windows will not be lowered, and it will not be possible to open the convertible top.

Convenient opening and closing

Convenient operation is possible via the remote control, refer to page 32, and the door lock, re‐ fer to page 34.

Manual closing in case of electrical malfunction

Only close the convertible top manually if

there is an electrical malfunction

Only close the convertible top manually if this is absolutely necessary; never open it manually. Damage may occur if incorrectly operated. The closing procedure must be fully completed; otherwise, there is a risk of injury or damage.◀

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 47

Opening and closing

CONTROLS

Before closing

1. Take the hex key and screwdriver out of the

onboard vehicle tool kit, refer to page 241.

2. Pry out the trunk lamp in the left side trim

using the screwdriver, arrow.

3. Using the screwdriver, unscrew the gold-

colored screw by approx. one and a half turns.

Unlocking the convertible top

Release the screw, arrow, using the hex key

and take it out.

3. Pull the sensor out of the cover, arrow, and

set it down on the inside side trim.

4. Release the second screw, arrow, using the

hex key to unlock the convertible top.

5. Take out the screw.

6. Lift the side frame slightly, arrow 1, and pull

the sensor and cable forward out of the guide.

7. Pivot the cable out sideways, arrow 2.

When setting it down, ensure that the cable is not pinched.

2. Slide the cover in the direction of travel, ar‐

row 1, and twist it out sideways, arrow 2. If necessary, push the plastic trim, arrow 3, inward slightly.

Online Edition for Part no. 01 40 2 961 056 - II/15

8. Unlock the second side frame.

Page 48

CONTROLS

Opening and closing

Closing the convertible top

1. Hold on to the convertible top on the re‐

spective side frames with both hands.

2. Lift it out on both sides and pivot it forward

onto the cowl.

3. In the vehicle, pry out the cover in the mid‐

dle of the roof using the screwdriver.

Closing the sliding sunroof

Insert the hex key into the opening de‐

signed for this purpose in the middle of the roof and press upward, arrow 1.

Ensure that the locking pieces do not fall onto the vehicle, as this could cause dam‐ age.

4. Insert the pins into the respective mount on

the cowl, arrow.

Locking the convertible top

Turn the hex key opposite to the direction of arrow 2 until the convertible top is locked.

Please contact your service center to eliminate the malfunction.

MINI Convertible: wind deflector

2. Turn the hex key in the direction of arrow 2.

3. Open the two locks and take off the locking

pieces.

Online Edition for Part no. 01 40 2 961 056 - II/15

The wind deflector keeps air movements in the passenger compartment to a minimum when the convertible top is open and provides an even more comfortable ride, even at high speeds.

Do not allow pointed object to come into con‐ tact with the wind deflector as these may dam‐ age the net. Do not place any objects on the in‐ stalled wind deflector. When stowing, make sure that the wind deflector is not damaged by objects.

Before installing

Take the wind deflector out of the pouch.

Page 49

Opening and closing

CONTROLS

2. Unfold the wind deflector, see arrows.

3. Push together the catches until they en‐

gage, see arrows.

Mounting and unfolding

4. Push out retaining pin 2 until it engages.

5. Fold up the upper part of the wind deflec‐

tor.

Do not damage the wind deflector

In the rearmost seat position, do not in‐ cline the backrest too far back; otherwise, the wind deflector could be damaged.◀

Removing and folding up

The unit is removed in the reverse order from which it was mounted.

Push out retaining pin 2 on one side until it

engages.

2. Insert the retaining pins of the wind deflec‐

tor into the provided openings 1 and 2 on this side of the vehicle.

3. Push back retaining pin 1 against the spring

force on the other side of the vehicle and insert it in the provided opening.

Online Edition for Part no. 01 40 2 961 056 - II/15

Push the unlocking lever to the middle of the wind deflector and fold up both halves.

MINI Roadster: manual convertible top

General information

The fabric convertible top combines reliable weather protection with simple and convenient operation.

Page 50

CONTROLS

Opening and closing

To ensure that you will continue to enjoy your MINI Convertible, here are a few tips:

▷ It is advisable that you close the convertible

▷ Do not attach roof rack systems to the

convertible top.

Safety notes on the convertible top

▷ Do not leave the convertible top open

for longer than one day while it is wet; otherwise, damage could be caused by the moisture.

▷ Do not place any objects on the convertible

top; otherwise, they could fall during oper‐ ation of the convertible top and cause damage or injury.

▷ The convertible top pivots up when it is

opened and closed. When moving the convertible top in places like garages, en‐ sure that there is a minimum height of 79 inches/2 meters; otherwise, damage could result.

▷ Always carry out the convertible top move‐

ment to the end. Driving when the convertible top is not fully opened or closed may result in damage or injury.

▷ During opening and closing, ensure that

people cannot be injured by the convertible top frame or other moving parts. Keep chil‐ dren away from the opening path of the convertible top.

▷ For safety reasons, only move the

convertible top while the vehicle is station‐ ary, if possible.

▷ Do not place any objects on the convertible

top; otherwise, they could fall during oper‐ ation of the convertible top and cause damage or injury.◀

Opening

1. Fold out the handle and turn it all the way

to the end, arrow.

2. Push the unlocked convertible top upward

at the handle and open it about a hand's width.

3. Exit the vehicle.

4. Guide the convertible top to the rear.

5. Push down on the convertible top with

some momentum until it engages audibly.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 51

Opening and closing

CONTROLS

Closing

1. Switch the ignition on so that the windows

can be slightly lowered automatically. Re‐ move the wind deflector if necessary.

2. Press button 1.

The convertible top is unlocked and moves up slightly.

3. Exit the vehicle.

4. Guide the convertible top forward.

5. Pull the convertible top onto the windshield

frame.

6. Turn the handle clockwise until it engages

audibly.

The convertible top is locked.

If the convertible top was open for a lengthy period, it may be necessary to ap‐ ply greater force when locking the top.

7. Fold the handle back in.

MINI Roadster: semi-auto‐ matic convertible top

General information

The fabric convertible top combines reliable weather protection with simple and convenient operation.

To ensure that you will continue to enjoy your MINI Convertible, here are a few tips:

▷ It is advisable that you close the convertible

top when you park the vehicle. Not only does the closed convertible top protect the

vehicle interior against unanticipated weather damage, it also offers a certain amount of theft protection. However, even when the convertible top is closed, valua‐ bles should only be stored in the locked cargo area.

▷ Do not attach roof rack systems to the

convertible top.

Safety notes on the convertible top

▷ At temperatures below +14 ℉/-10 ℃,

do not move the convertible top or else damage could result.

▷ Do not leave the convertible top open for

longer than one day while it is wet; other‐ wise, damage could be caused by the mois‐ ture.

▷ Do not place any objects on the convertible

top; otherwise, they could fall during oper‐ ation of the convertible top and cause damage or injury.

▷ The convertible top pivots up when it is

opened and closed. When moving the convertible top in places like garages, en‐ sure that there is a minimum height of 79 inches/2 meters; otherwise, damage could result.

▷ Always carry out the convertible top move‐

ment to the end. Driving when the convertible top is not fully opened or closed may result in damage or injury.

▷ During opening and closing, ensure that

people cannot be injured by the convertible top frame or other moving parts. Keep chil‐ dren away from the opening path of the convertible top.

▷ For safety reasons, only move the

convertible top while the vehicle is station‐ ary, if possible.◀

Operation while driving

The convertible top can be opened or closed while driving at vehicle speeds up to approx. 20 mph/30 km/h.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 52

CONTROLS

Opening and closing

Pay close attention to the traffic

For better control

The indicator lamp lights up. Movement of the convertible top is completed. The convertible top is fully opened.

The indicator lamp lights up. Movement of the convertible top is completed. Close the convertible top using the han‐

dle.

Malfunction

The "convertible top not locked" indicator lamp lights up and a message appears on the Control Display.

able to reactivate the convertible top in this case:

1. Switch the ignition off and on again.

2. Press the switch to continue the sequence

in the desired direction.

Opening and closing the convertible top

Switch on the radio ready state or the ignition, refer to page 64.

If possible, conserve the battery by only operat‐ ing the convertible top while the engine is run‐ ning.

Before closing the convertible top, remove all foreign objects from the windshield frame that could prevent the top from closing properly.

Opening

Fold out the handle and turn it all the way

to the end, arrow.

Interruption

Danger

A convertible top that is not fully opened

or closed is a source of danger.◀

When the opening or closing procedure is inter‐ rupted because the switch is released, the convertible top remains in the position in which it stopped. The sequence can be continued us‐ ing the switch.

The opening or closing procedure is also inter‐ rupted when it is blocked mechanically. To be

Online Edition for Part no. 01 40 2 961 056 - II/15

2. Push the unlocked convertible top upward

at the handle and open it about a hand's width.

Page 53

Opening and closing

CONTROLS

3. Press the switch back to open the

convertible top. The windows opens during this procedure.

Closing

1. Press the switch forward.

2. Pull the convertible top onto the windshield

frame.

3. Turn the handle clockwise until it engages

audibly.

The convertible top is locked.

If the convertible top was open for a lengthy period, it may be necessary to ap‐ ply greater force when locking the top.

4. Fold the handle back in.

5. Close the windows if necessary.

Manual closing in case of electrical malfunction

Only close the convertible top manually if there is an electrical malfunction

2. Take out the cargo area insert, arrow.

3. Using the hex key from the onboard vehicle

tool kit, unscrew the gold-colored screw, see arrow, all the way to the stop, approx. four to five turns.

Closing

Hold on to the convertible top frame and

guide it to the windshield frame.

2. Fold out the handle and turn it counter‐

clockwise all the way to the stop.

3. Pull the convertible top onto the windshield

frame.

4. Turn the handle clockwise until it engages

audibly.

The convertible top is locked.

Before closing

Lower the side windows slightly, switch off the engine, and switch off the ignition.

Take out the cover plate, refer to

page 116.

Online Edition for Part no. 01 40 2 961 056 - II/15

MINI Roadster: wind de‐ flector

The wind deflector keeps air movements in the passenger compartment to a minimum when the convertible top is open and provides a comfortable ride, even at high speeds.

Page 54

CONTROLS

Opening and closing

Do not allow pointed object to come into con‐ tact with the wind deflector as these may dam‐ age the net.

Before installing

1. Take the wind deflector out of the storage

pouch.

2. Unfold the wind deflector, arrow.

Installation

Insert the wind deflector with parts 1 facing

back into the holders 2 on the rollover bars.

Storage

Fold up the wind deflector 1 and slide it into the storage pouch 2.

The wind deflector can be stored on the rear storage shelf behind the seats, refer to page 120.

2. Push the wind deflector down until it en‐

gages, arrow 3.

Attach the wind deflector properly

The wind deflector must be firmly en‐ gaged; otherwise, it may come lose from the fixations at high speeds.◀

Removing

The unit is removed in the reverse order from which it was mounted. Pull the wind deflector upward out of the holders.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 55

Adjusting

CONTROLS

Vehicle equipment

When using the features and systems described here, adhere to local regulations.

Sitting safely

The ideal seating position can make a vital con‐ tribution to relaxed, fatigue-free driving.

The seating position plays an important role in an accident in combination with:

▷ Safety belts, refer to page 55.

▷ Head restraints, refer to page 56.

▷ Airbags, refer to page 89.

safety belt in an accident. This would eliminate the protection normally provided by the belt.◀

Seat adjustment

Forward/backward

Pull the lever, arrow 1, and slide the seat into the desired position, arrows 2.

After releasing the lever, move the seat forward or back slightly to make sure it engages prop‐ erly.

Height

Seats

Note before adjusting

Do not adjust the seat while driving

Never attempt to adjust the driver's seat while driving. The seat could respond with un‐ expected movement and the ensuing loss of vehicle control could lead to an accident.◀

Do not incline the backrest too far to the

rear

Do not incline the backrest on the front passen‐ ger side too far to the rear during driving. Oth‐ erwise, there is the danger of sliding under the

Online Edition for Part no. 01 40 2 961 056 - II/15

Pull the lever up or push it down repeatedly, ar‐ rows 1, until the desired height is reached, ar‐ rows 2.

Page 56

CONTROLS

Adjusting

Backrest tilt

Pull the lever, arrow 1, and apply your weight to the backrest or lift it off, as necessary, ar‐ rows 2.

Lumbar support

You can also adjust the contour of the backrest to obtain additional support in the lumbar re‐ gion.

The upper hips and spinal column receive sup‐ plementary support to help you maintain a re‐ laxed, upright sitting position.

Turn the wheel to increase or decrease the cur‐ vature.

Entry in the rear

MINI Convertible: entry in the rear.

MINI Coupe, MINI Roadster: access to the rear storage shelf.

Pull the lever on the back of the seat up‐

ward, arrow 1.

The backrest folds forward.

2. Push against the backrest to move the seat

forward, arrow 2.

Restoring the original seat position

The driver's seat has a mechanical memory function for the forward/backward seat setting and the backrest setting.

Push the seat back to the original position.

Do not fold back the backrest until the seat is in its original position; otherwise, the seat will engage in its current position. If this happens, adjust the forward/backward po‐ sition manually, refer to page 53.

2. Fold back the backrest to lock the seat.

Note the following when moving back the seat

When moving back the seat, ensure that per‐ sons cannot be injured and objects cannot be damaged. Lock the front seats and front back‐ rests before driving away; otherwise, there is the risk of an accident if the seat or backrest moves unexpectedly.◀

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 57

Adjusting

CONTROLS

Seat heating

Switching on

The temperature setting progresses one step through its control sequence each time you press the button. The maximum temperature is reached when three LEDs are lit.

If the trip is continued within approx. 15 mi‐ nutes, the seat heating is activated automati‐ cally with the temperature set last.

The temperature is reduced, if need be, down to no heat in order to reduce the load on the battery. The LEDs remain lit.

Switching off

Press the button longer.

Safety belts

Although airbags enhance safety by providing added protection, they are not a substitute for safety belts.

The shoulder strap's anchorage point will be correct for adult seat occupants of every build if the seat is correctly adjusted.

One person per safety belt

Never allow more than one person to wear a single safety belt. Never allow infants or small children to ride on a passenger's lap.◀

Putting on the belt

Lay the belt, without twisting, snugly across the lap and shoulders, as close to the body as possible. Make sure that the belt lies low around the hips in the lap area and does not press on the abdomen. Otherwise, the belt can slip over the hips in the lap area in a frontal impact and injure the abdomen.

The safety belt must not lie across the neck, rub on sharp edges, be routed over solid or breaka‐ ble objects, or be pinched.◀

Reduction of restraining effect

Avoid wearing clothing that prevents the belt from fitting properly, and pull the shoulder belt periodically to readjust the tension across your lap; otherwise, the retention effect of the safety belt may be reduced.◀

Number of safety belts

Your vehicle has been fitted with safety belts for the safety of you and your passengers:

▷ MINI Coupe, MINI Roadster: two safety

belts.

▷ MINI Convertible: four safety belts.

However, they can only offer protection when adjusted correctly.

Notes

Always make sure that safety belts are being worn by all occupants before driving away.

Online Edition for Part no. 01 40 2 961 056 - II/15

Buckling the belt

Make sure you hear the latch plate engage in the belt buckle.

Page 58

CONTROLS

Adjusting

The shoulder strap's anchorage point will be correct for adult seat occupants of every build if the seat is correctly adjusted, refer to page 53.

Unbuckling the belt

1. Hold the belt firmly.

2. Press the red button in the belt buckle.

3. Guide the belt back into its reel.

MINI Convertible: rear belt guide

When fastening the safety belts on the rear seats, ensure that the belt guide loop, arrow, is closed.

Safety belt reminder for driver's seat and front passenger seat

The indicator lamps light up and a sig‐ nal sounds. In addition, a message ap‐ pears on the Control Display. Check whether the safety belt has been fas‐

tened correctly.

Damage to safety belts

In the case of strain caused by accidents or damage:

Have the safety belts, including the safety belt tensioners, replaced and have the belt anchors checked.

Checking and replacing safety belts

Have the work performed only by your service center; otherwise, it cannot be ensured that this safety feature will function properly.◀

Head restraints

Correctly set head restraint

A correctly adjusted head restraint reduces the risk of spinal injury in the event of an accident.

Adjusting the head restraint

Correctly adjust the head restraints of all occupied seats; otherwise, there is an increased risk of injury in an accident.◀

Height

Adjust the head restraint so that its center is approx. at ear level.

Distance

Adjust the distance so that the head restraint is as close as possible to the back of the head.

Height adjustment

To raise: pull.

To lower: press the button, arrow 1, and push the head restraint down until it engages.

Removing

Only remove the head restraint if no one will be sitting in the seat in question.

Pull the head restraint upward as far as

possible.

2. Press the button, arrow 1, and pull the

head restraint out completely.

To remove the head restraint, fold the backrest forward if necessary.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 59

Adjusting

CONTROLS

Before transporting passengers

Reinstall the head restraint before trans‐ porting anyone in the seat; otherwise, the pro‐ tective function of the head restraint is unavail‐ able.◀

Mirrors

Exterior mirrors

General information

The mirror on the passenger side is more curved than the driver's mirror.

Estimating distances correctly

Objects reflected in the mirror are closer than they appear. Do not estimate the distance to the traffic behind you based on what you see in the mirror, as this will increase your risk of an accident.◀

At a glance

1 Setting the left or right exterior mirror

2 Folding the mirror in and out

Adjusting electrically

1. Select the mirror by turning the knob to the

respective position 1.

2. To adjust the mirror, move the knob in the

desired direction: to the front, rear, left, or right.

Adjusting manually

If an electrical malfunction occurs, for example, press the edges of the mirror glass.

Folding the mirror in and out

Turn the knob past the resistance point in di‐ rection 2.

The mirror can be folded in up to a vehicle speed of approx. 20 mph/30 km/h.

For example, this is advantageous

▷ In car washes.

▷ In narrow streets.

▷ For folding back mirrors that were folded

away manually.

Fold in the mirror in a car wash

Before entering an automatic car wash, fold in the exterior mirrors by hand or with the button; otherwise, they could be damaged, de‐ pending on the width of the vehicle.◀

Automatic heating

Both exterior mirrors are heated automatically while the engine is running or the ignition is switched on when the external temperature is below a certain value.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 60

CONTROLS

Adjusting

Interior rearview mirror

To reduce the blinding effect from the rear when driving at night: turn the knob.

Interior rearview and exterior mirrors, automatic dimming feature

Two photocells are used for control:

▷ In the mirror frame, see arrow.

▷ On the back of the mirror.

Steering wheel

Adjusting

Do not adjust while driving

Do not adjust the steering wheel while driving; otherwise, an unexpected movement could result in an accident.◀

1. Fold the lever down.

2. Move the steering wheel to the preferred

height and angle to suit your seating posi‐ tion.

3. Fold the lever back.

Do not use force to swing the lever back.

Do not use force to swing the lever back up; otherwise, the mechanism will be dam‐ aged.◀

For proper operation:

▷ Keep the photocells clean.

▷ Do not cover the area between the inside

rearview mirror and the windshield.

▷ Do not apply stickers to the windshield in

front of the mirror.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 61

Transporting children safely

CONTROLS

Vehicle equipment

When using the features and systems described here, adhere to local regulations.

The right place for chil‐ dren

Notes

Children in the vehicle

Do not leave children unattended in the vehicle; otherwise, they could endanger them‐ selves and other persons, e.g., by opening the doors.◀

MINI Convertible: children should always be in the rear

Accident research shows that the safest place for children is on the rear seat.

Transporting children in the rear

Transport children younger than 13 years of age or shorter than 5 ft/150 cm in the rear only, using child restraint fixing systems suita‐ ble for the age, weight, and height of the child; otherwise, there is an increased risk of injury in an accident.

Children 13 years of age or older must wear a safety belt as soon as a suitable child restraint fixing system can no longer be used, due to their age, weight and size.◀

Installing child seats

Only install child seats in the rear when the rear seat backrest is folded all the way back and engaged; otherwise, there is an increased risk of injury in an accident.◀

Children on the front passenger seat

Front passenger airbags

Should it be necessary to use a child restraint fixing system on the front passenger seat, make sure that the front and side airbags on the front passenger side are deactivated, refer to page 90.

Deactivating the front passenger airbags

If a child restraint fixing system is used in the front passenger seat, the front passenger airbags must be deactivated; otherwise, there is an increased risk of injury to the child when the airbags are triggered, even with a child re‐ straint fixing system.◀

Installing child re‐ straint fixing systems

Notes

Manufacturer's information for child re‐

straint fixing systems

To select, mount and use child restraint fixing systems, observe the information provided by the system manufacturer; otherwise, the pro‐ tective effect can be impaired.◀

On the front passenger seat

Deactivating the airbags

After installing a child restraint fixing system on the front passenger seat, ensure that the front

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 62

CONTROLS

Transporting children safely

and side airbags on the front passenger side are deactivated.

Deactivating the front passenger airbags

Seat position and height

Before installing a child restraint fixing system, move the front passenger seat as far back as possible and adjust its height to the highest po‐ sition to obtain the best possible position for the belt and to offer optimal protection in the event of an accident.

Do not change this seat position once it has been set.

Child seat security

MINI Coupe, MINI Roadster

The safety belt for the passenger can be locked to prevent it from being pulled out when it is used to secure child restraint systems.

MINI Convertible

All rear safety belts and the safety belt for the front passenger can be locked to prevent ex‐ tension in order to permit attachment of child restraint fixing systems.

To lock the safety belt

Secure the child restraint fixing system with

the belt.

2. Pull out the belt webbing completely.

3. Allow the belt webbing to be pulled in and

pull it taut against the child restraint fixing system.

The safety belt is locked.

To unlock the safety belt

Open the belt buckle.

2. Remove the child restraint fixing system.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 63

Transporting children safely

3. Allow the belt webbing to be pulled in com‐

pletely.

Guide the safety belt to the holder on the headliner.

MINI Convertible: LATCH child restraint fixing system

LATCH: Lower Anchors and Tethers for Children.

Notes

Manufacturer's information for LATCH child restraint fixing systems

To mount and use the LATCH child restraint fix‐ ing systems, observe the operating and safety information from the system manufacturer; otherwise, the level of protection may be re‐ duced.◀

CONTROLS

The mounts for the lower LATCH anchors are located behind the indicated cover caps.

The corresponding symbol shows the mounts for the lower LATCH anchors. Seats that are equipped with lower an‐ chors are labeled with two, 2, LATCH symbols. It is not recommended to use

the inner lower anchors of standard ISOFIX outer positions to secure a child restraint system in the middle. Use the safety belt for middle positions instead.

Mounts for the lower LATCH anchors

The lower anchors may be used to attach the CRS to the vehicle seat up to a combined child and CRS weight of 65 lb/30 kg when the child is restrained by the internal harnesses.

Correctly engage the lower LATCH an‐ chors

Make sure that the lower LATCH anchors have properly engaged and that the child restraint fixing system is resting snugly against the back‐ rest; otherwise, the degree of protection of‐ fered may be reduced.◀

Before installing the child seat, pull the belt out of the area for the child restraint fixing system.

Online Edition for Part no. 01 40 2 961 056 - II/15

Mounting LATCH child restraint fixing systems

Mount the child restraint fixing system; re‐

fer to the operating instructions of the sys‐ tem.

2. Ensure that both LATCH anchors are prop‐

erly connected.

Child restraint fixing systems with an upper re‐ taining strap

Mounting points

LATCH mounting points

Only use the mounting points for the up‐ per LATCH retaining strap to secure child re‐ straint systems; otherwise, the mounting points could be damaged.◀

MINI Coupe:

Page 64

CONTROLS

Transporting children safely

There is one additional mounting point for child restraint fixing systems with an upper retaining strap, arrow.

MINI Convertible:

There are two additional mounting points for child restraint fixing systems with an upper re‐ taining strap, arrows.

Guide of the upper LATCH retaining strap

Retaining strap

Make sure the upper retaining strap does not run over sharp edges and is not twisted as it passes to the top anchor. Otherwise, the strap will not properly secure the child restraint fixing system in the event of an accident.◀

MINI Coupe:

1 Direction of travel

2 Head restraint

3 Separating wall

4 Cargo area floor

5 Hook for upper retaining strap

6 Mounting point

7 Backrest

8 Upper retaining strap of child restraint fix‐

ing system

MINI Convertible:

1 Direction of travel

2 Head restraint

3 Rollover protection system with crossbar

4 Cargo cover

5 Cargo area floor

6 Hook for upper retaining strap

7 Mounting point

8 Backrest

9 Upper retaining strap of child restraint fix‐

ing system

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 65

Transporting children safely

Attaching the upper retaining strap to the mounting point

MINI Coupe

1. Remove the front cargo cover, refer to

page 116.

2. Slide the head restraint upward.

3. Guide the upper retaining strap between

the supports of the head restraint.

4. Attach the upper retaining strap to the

mounting point with the hook.

5. Slide the head restraint into the bottom po‐

sition.

6. Pull the upper retaining strap taut.

MINI Convertible

Ensure that the upper retaining strap 9 is passed between backrest 8 and rollover protec‐ tion system with crossbar 3; otherwise, it will be unable to properly restrain the child restraint fixing system.

Slide the head restraint upward.

2. Unlock the backrest and fold it forward

slightly, refer to page 117.

3. Guide the upper retaining strap between

the supports of the head restraint.

4. Attach the upper retaining strap to the

mounting point with the hook.

5. Fold back the backrest and lock it. Slide the

head restraint down as far as possible.

6. Pull the upper retaining strap taut.

CONTROLS

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 66

CONTROLS

Driving

Vehicle equipment

When using the features and systems described here, adhere to local regulations.

Ignition lock

Insert the remote control into the ignition lock

Insert the remote control all the way into the ignition lock.

Before removing the remote control, push it all the way in to release the locking mechanism.

The ignition is switched off if it was on.

Steptronic transmission

You can only take out the remote control if transmission position P is engaged: interlock.

Start/Stop button

Pressing the Start/Stop button switches the ig‐ nition on or off and starts the engine.

The engine starts when the Start/Stop button is pressed and:

▷ Manual transmission: the clutch pedal is de‐

pressed.

▷ Steptronic transmission: the brake pedal is

depressed.

Radio ready state is switched on. Individual electrical consumers can operate.

Removing the remote control from the ignition lock

Do not forcibly pull the remote control out of the ignition lock

Do not forcibly pull the remote control out of the ignition lock as this may cause damage.◀

Online Edition for Part no. 01 40 2 961 056 - II/15

Radio ready state

Individual electrical consumers can operate.

Radio ready state is switched off automatically:

▷ When the remote control is removed from

the ignition lock.

▷ With Comfort Access, refer to page 37, by

pressing the button on the door handle or

the

▷ After a certain period of time.

button on the remote control.

Page 67

Driving

CONTROLS

Ignition on

All electrical consumers can operate. Most indi‐ cator and warning lights light up for different lengths of time.

To save battery power when the engine is off, switch off the ignition and any unnecessary electronic systems/power consumers.

Radio ready state and ignition off

All indicator and warning lights in the displays go out.

The ignition switches off automatically when the driver's door is opened. Pressing the Start/ Stop button again switches the ignition back on.

For example, the ignition is not switched off in the following situations:

▷ Depress the clutch or brake pedal.

▷ The low beams are switched on.

Starting the engine

General information

Enclosed areas

Do not let the engine run in enclosed areas; otherwise, breathing of exhaust fumes may lead to loss of consciousness and death. The exhaust gases contain carbon monoxide, an odorless and colorless but highly toxic gas.◀

Unattended vehicle

Do not leave the car unattended with the engine running; otherwise, it presents a poten‐ tial source of danger.

Before leaving the car with the engine running, shift to neutral or engage transmission posi‐ tion P and set the parking brake firmly; other‐ wise, the vehicle may begin to roll.◀

Frequent starting in quick succession

Avoid repeated futile attempts at starting the car and avoid starting the car frequently in quick succession. Otherwise, the fuel is not burned or is inadequately burned, and there is the danger of overheating and damaging the catalytic converter.◀

Do not wait for the engine to warm-up while the vehicle remains stationary; start driving right away, but at moderate engine speeds.

Do not depress the accelerator when starting the engine.

Starting the engine

Manual transmission

Remote control in the ignition lock or with Comfort Access inside the vehicle, refer to page 37.

Depress the brake pedal.

2. Depress the clutch pedal.

3. Press the Start/Stop button.

The ignition is activated automatically for a cer‐ tain time and is stopped as soon as the engine starts.

Steptronic transmission

Remote control in the ignition lock or, with Comfort Access, inside the vehicle, refer to page 37.

Depress the brake pedal.

2. Move the selector lever to position P or N.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 68

CONTROLS

Driving

3. Press the Start/Stop button.

The ignition is activated automatically for a cer‐ tain time and is stopped as soon as the engine starts.

Engine stop

General information

Take the remote control with you

Take the remote control with you when leaving the vehicle so that children, for exam‐ ple, cannot operate the windows and injure themselves.◀

Set the parking brake and further secure

the vehicle as required

Set the parking brake firmly when parking; oth‐ erwise, the vehicle may roll. On steep upward and downward inclines, further secure the ve‐ hicle, for example, by turning the steering wheel in the direction of the curb.◀

Before driving into a car wash

To make it possible for the vehicle to roll in an automatic car wash, follow the information on Washing in automatic car washes, refer to page 258.

Steptronic transmission

1. Engage transmission position P with the ve‐

hicle stopped.

2. Press the Start/Stop button.

3. Set the parking brake firmly.

4. Remove the remote control from the igni‐

tion lock.

Parking brake

The concept

The parking brake is primarily intended to pre‐ vent the vehicle from rolling while parked; it brakes the rear wheels.

Also follow the instructions under Switching off the engine, refer to page 66.

Setting

The lever engages automatically.

Releasing

Switching off the engine

Manual transmission

With the vehicle at a standstill, press the

Start/Stop button.

2. Shift into first gear or reverse.

3. Set the parking brake firmly.

4. Remove the remote control from the igni‐

tion lock.

Online Edition for Part no. 01 40 2 961 056 - II/15

Pull up slightly, press the button, and lower the lever.

Notes

Using the parking brake while driving

If it should become necessary to use the parking brake while driving, do not pull the parking brake too forcefully. Keep the button on the parking brake lever pressed at all times.

Page 69

Driving

CONTROLS

Excessive application of the parking brake can block the rear wheels and lead to fishtailing of the vehicle.◀

The brake lights do not light up when the park‐ ing brake is pulled.

Turn signal, high-beams, headlight flasher

1 Turn signal

2 Switching on the high-beams

3 Switching off the high-beams/headlight

flasher

Turn signal

Press the lever beyond the resistance point.

To switch off manually, press the lever to the resistance point.

Unusually rapid flashing of the indicator lamp indicates that a turn signal bulb has failed.

2. "Lighting"

3. "Triple turn signal"

The setting is stored for the remote control cur‐ rently in use.

Washer/wiper system

Notes

Do not switch on the wipers if frozen

Do not switch on the wipers if they are frozen onto the windshield; otherwise, the wiper blades and the windshield wiper motor may be damaged.◀

Do not use the wipers on a dry windshield

Do not use the wipers on a dry wind‐ shield; otherwise, the wiper blades may wear more rapidly or become damaged.◀

At a glance

Signaling a turn briefly

Press the lever to the resistance point and hold it there for as long as you want the turn signal to flash.

Triple turn signal activation

Press the lever to the resistance point.

The turn signal flashes three times.

This function can be activated or deactivated:

"Settings"

Online Edition for Part no. 01 40 2 961 056 - II/15

1 Switching on wipers

2 Switching off wipers or brief wipe

Page 70

CONTROLS

Driving

3 Activating/deactivating intermittent wipe or

the rain sensor

4 Cleaning the windshield and headlights

Switching on wipers

Press the wiper lever upward, arrow 1.

The lever automatically returns to its initial po‐ sition when released.

Normal wiper speed

Press up once.

The system switches to operation in the inter‐ mittent mode when the vehicle is stationary.

Fast wiper speed

Press up twice or press once beyond the resist‐ ance point.

The system switches to normal speed when the vehicle is stationary.

Switching off wipers or brief wipe

Press the wiper lever down, arrow 2.

The lever automatically returns to its initial po‐ sition when released.

▷ Brief wipe: press down once.

▷ To switch off normal wipe: press down

once.

▷ To switch off fast wipe: press down twice.

Intermittent wipe or rain sensor

If the car is not equipped with a rain sensor, the intermittent-wipe time is a preset.

If the car is equipped with a rain sensor, the time between wipes is controlled automatically and depends on the intensity of the rainfall.

The rain sensor is mounted on the windshield, directly in front of the interior rearview mirror.

Deactivate the rain sensor in car washes

Deactivate the rain sensor when passing through an automatic car wash; otherwise, damage could be caused by undesired wiper activation.◀

Activating intermittent wipe or rain sensor

Press the button, arrow 3.

The symbol is shown in the tachometer.

Setting the sensitivity of the rain sensor

Switch on the ignition, refer to page 65.

2. Press the button on the turn indicator lever

repeatedly until "SET/INFO" is displayed.

3. Press and hold the button until the display

changes.

4. Press the button repeatedly until the sym‐

bol and "SET" are displayed.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 71

Driving

CONTROLS

5. Press and hold the button until the display

changes.

6. Press the button to select the desired sensi‐

tivity.

7. Wait or hold the button until the display

changes.

The settings were stored.

Deactivating intermittent wipe or rain sensor

Press the button again, arrow 3.

Cleaning the windshield and headlights

Pull the lever, arrow 4.

The system sprays washer fluid on the wind‐ shield and activates the wipers briefly.

When the vehicle lighting system is switched on, the headlights are cleaned at regular and appropriate intervals.

Do not use the washer system at freezing temperatures

Do not use the washers if there is any danger that the fluid will freeze on the windshield; oth‐ erwise, your vision could be obscured. For this reason, use antifreeze.

Avoid using the washer when the reservoir is empty; otherwise, you could damage the pump.◀

Do not use the washing facilities when the hood is open

Only use the washing facilities when the hood is fully locked; otherwise, the headlamp washer system may become damaged.◀

Windshield washer nozzles

The windshield washer nozzles are heated au‐ tomatically while the engine is running or the ignition is switched on.

Washer fluid

General information

Antifreeze for washer fluid

Antifreeze is flammable and can cause in‐

juries if used improperly.

Therefore, keep it away from sources of igni‐ tion.

Only keep it in the closed original container and inaccessible to children.

Follow the notes and instructions on the con‐ tainer.

United States: The washer fluid mixture ratio is regulated by the U.S. EPA and many individual states; do not exceed the allowable washer fluid dilution ratios limits that apply. Follow the usage instructions on the washer fluid con‐ tainer. Use BMW's Windshield Washer Concen‐ trate or the equivalent.◀

Washer fluid reservoir

Adding washer fluid

Only add washer fluid when the engine is cool, and then close the cover completely to avoid contact between the washer fluid and hot engine parts.

Otherwise, there is the danger of fire and a risk to personal safety if the fluid is spilled.◀

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 72

CONTROLS

All washer nozzles are supplied from one reser‐ voir.

Driving

Reverse gear

Select only when the vehicle is stationary. When the gearshift lever is pressed to the left, a slight resistance needs to be overcome.

Steptronic transmission

In addition to the fully automatic mode, gears can also be shifted manually using Steptronic, refer to page 71.

The recommended minimum filling quantity is

0.2 US gal/1 liter.

Fill with a mixture of window washing concen‐ trate and water; if needed, add antifreeze ac‐ cording to the manufacturer instructions.

Mix the washer fluid before adding to maintain the correct mixing ratio.

Do not fill in undiluted window washing con‐ centrate and do not fill in pure water; this could damage the washer system.

Do not mix window washing concentrate from different manufacturers; this could cause the washer nozzles to clog.

Manual transmission

Parking the vehicle

Secure the vehicle

Before leaving the vehicle with the en‐ gine running, move the selector lever to posi‐ tion P and set the handbrake; otherwise, the vehicle will begin moving.◀

Disengaging the remote control

To remove the remote control from the ignition lock, first move the selector lever to position P and switch off the engine: interlock. Remove the remote control from the ignition lock, refer to page 64.

Selector lever positions

P R N D M/S + –

Displays in the tachometer

Pay attention to the shift plane

When shifting into 5th or 6th gear, push the gearshift lever to the right; otherwise inad‐ vertent shifting into the 3rd or 4th gear could lead to engine damage.◀

Online Edition for Part no. 01 40 2 961 056 - II/15

The selector lever position is displayed and the engaged gear, such as M4, is displayed in manual mode.

Page 73

Driving

CONTROLS

Changing selector lever positions

▷ With the ignition switched on or the engine

running, the selector lever can be moved out of position P.

▷ When the vehicle is stationary, step on the

brake before shifting out of P or N; other‐ wise, the selector lever is locked: shiftlock.

Press on the brake pedal until you start driving

To prevent the vehicle from creeping after you select a driving position, maintain pres‐ sure on the brake pedal until you are ready to start.◀

A lock prevents accidental shifting into selector lever positions R and P.

To override the lock, press the button on the front of the selector lever, see arrow.

P Park

Select only when the vehicle is stationary. The front wheels are blocked.

R is Reverse

Select only when the vehicle is stationary.

N is Neutral

For example, engage this position in a car wash. The vehicle can roll.

D Drive

Position for normal vehicle operation. All for‐ ward gears are selected automatically.

Under normal operating conditions, fuel con‐ sumption is lowest when you are driving in po‐ sition D.

Kickdown

Kickdown is used to achieve maximum driving performance. Press on the accelerator beyond the resistance point at the full throttle position.

Sport program and manual mode M/S

Activating the Sport program

Move the selector lever from position D toward the left into the M/S shifting slot.

The Sport program is activated and DS is dis‐ played. This position is recommended for a per‐ formance-oriented driving style.

To deactivate the Sport program or manual mode M/S, move the selector lever to the right into position D.

Activating the M/S manual mode

Move the selector lever from position D toward the left into the M/S shifting slot.

Push the selector lever forward or backward.

Manual mode becomes active and the gear is changed.

The tachometer displays the engaged gear, e. g. M1.

▷ To shift up: press the selector lever back‐

ward.

▷ To shift down: press the selector lever for‐

ward.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 74

CONTROLS

Driving

The vehicle only shifts up or down at appropri‐ ate engine and road speeds, e.g., it does not shift down if the engine speed is too high. The selected gear is briefly displayed in the instru‐ ment panel, followed by the current gear.

Shifting gears using the shift paddles on the steering wheel

The shift paddles on the steering wheel allow you to shift gears quickly while keeping both hands on the steering wheel.

▷ When the shift paddles on the steering

wheel are used to shift gears while in auto‐ matic mode, the transmission switches to manual mode.

▷ If the shift paddles are not used to acceler‐

ate or shift gears for a certain amount of time, the transmission switches back to au‐ tomatic mode.

If the selector lever is in the M/S gear plane, manual mode remains active.

▷ Pull one of the two shift paddles:

The transmission shifts up.

▷ Press one of the two shift paddles:

The transmission shifts down.

Manually unlocking the selector lever lock

If the selector lever is locked in position P al‐ though the ignition is switched on, the brake is depressed, and the button on the selector lever is pressed, the selector lever lock can be over‐ ridden:

1. Switch off the ignition.

2. Unclip the sleeve of the selector lever.

3. Pull the sleeve up over the selector lever

until the sleeve is inside out.

Pull off the plug-in cable connector if nec‐ essary.

4. Insert the pulling hook 1 from the onboard

vehicle tool kit into the loop on the passen‐ ger side.

5. Pull the loop upward.

6. Move the selector lever into the desired po‐

sition, pressing the button on the front of the selector lever.

Set the parking brake

Manually unlock the selector lever lock for towing only. Before manually unlocking the selector lever lock, pull the parking brake firmly; otherwise, the vehicle may roll away and cause personal injury or property damage.◀

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 75

Displays

CONTROLS

Vehicle equipment

When using the features and systems described here, adhere to local regulations.

Odometer, external tem‐ perature display, clock

At a glance

1 Current speed

2 Odometer, trip odometer, external temper‐

ature, time

3 Resetting the trip odometer

Press the button on the turn indicator lever to open information in display area 2.

The following information is displayed consecu‐ tively:

▷ Trip odometer

▷ Time

▷ External temperature

Trip odometer

Displaying the trip odometer

Press button 3 briefly.

Resetting the trip odometer

1. Press button 3 briefly.

The trip odometer is displayed.

2. Press button 3 again.

The trip odometer is reset.

Time

Set the time, refer to page 78.

External temperature, external temperature warning

If the display drops to +37 ℉/+3 ℃, a signal sounds and a warning light lights up. There is the increased danger of ice.

Ice on roads

Even at temperatures above +37 ℉/+3 ℃, there can be a risk of ice on roads.

Therefore, drive carefully on bridges and shady roads, for example, to avoid the increased dan‐ ger of an accident.◀

Units of measure

To set the respective units of measure, miles or km for the odometer and ℃ or ℉ for the exter‐ nal temperature, refer to page 77.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 76

CONTROLS

Displays

Tachometer

It is imperative that you avoid engine speeds in the red warning field. In this range, the fuel supply is interrupted to protect the engine.

Coolant temperature

A warning lamp will come on if the coolant, and therefore the engine, becomes too hot. In addi‐ tion, a message will appear on the Control Dis‐ play.

Check the coolant level, refer to page 238.

Fuel gauge

Range

After the reserve range is reached:

▷ The remaining LEDs change from orange to

red, arrow.

▷ A message is briefly displayed on the Con‐

trol Display.

▷ The remaining range is shown on the tach‐

ometer.

▷ When a dynamic driving style is used, such

as when corners are taken rapidly, engine functions are not ensured.

The message appears continuously below a range of approx. 30 miles/50 km.

Refuel promptly

At the latest, refuel at a range below 30 miles/50 km; otherwise, the engine function is not ensured and damage may occur.◀

Computer

Opening information in the tachometer

The arrow next to the fuel pump symbol on the fuel gauge indicates the side of the vehicle with the fuel filler flap.

The vehicle inclination may cause the display to vary.

Notes on refueling, refer to page 216.

Filling capacities, refer to page 269.

Online Edition for Part no. 01 40 2 961 056 - II/15

Press the button on the turn indicator lever.

Overview of the information

The following information is displayed consecu‐ tively by repeatedly pressing the button on the turn indicator lever:

▷ Range.

▷ Average fuel consumption.

▷ Current fuel consumption.

Page 77

Displays

CONTROLS

▷ Average speed.

▷ MINI Roadster, MINI Convertible: Always

Open Timer.

To set the corresponding units of measure, re‐ fer to page 77.

Information in detail

Range

Displays the estimated cruising range available with the remaining fuel.

It is calculated based on your driving style over the last 18 miles/30 km.

Average fuel consumption

This is calculated for the period during which the engine is running.

With the trip computer, refer to page 75, the average consumption can be displayed for an additional distance.

To reset the average consumption: press the button on the turn indicator lever for ap‐ prox. 2 seconds.

Current fuel consumption

Displays the current fuel consumption. You can check whether you are currently driving in an efficient and environmentally-friendly manner.

Average speed

Periods in which the vehicle was parked and the engine was switched off manually are not included in the average speed calculations.

With the trip computer, refer to page 75, the average speed can be displayed for an addi‐ tional distance.

To reset the average speed: press the button on the turn indicator lever for approx. 2 sec‐ onds.

Displays on the Control Display

Display the computer or trip computer on the Control Display.

1. "Vehicle Info"

2. "Onboard info" or "Trip computer"

Displays on the "Onboard info":

▷ Range.

▷ Distance to destination.

▷ Estimated time of arrival if a destination

was entered in the navigation system.

Displays on the "Trip computer":

▷ Departure time.

▷ Trip duration.

▷ Trip distance.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 78

CONTROLS

Displays

Both displays show:

▷ Average fuel consumption.

▷ Average speed.

Resetting the fuel consumption and speed

Resetting the values for average speed and average fuel consumption:

1. Select the respective menu item and press

the MINI joystick.

2. Press the MINI joystick again to confirm

your selection.

Resetting the trip computer

Resetting all values:

"Vehicle Info"

2. "Trip computer"

3. "Reset"

Always Open Timer

Digital Always Open Timer

In the MINI Convertible and MINI Roadster, the driving times with the convertible top open can be digitally displayed in the tachometer. Press the button on the turn indicator lever repeat‐ edly until the driving times are displayed.

To reset the current driving time: press the but‐ ton on the turn indicator lever or button 2 for approx. 2 seconds while the driving times are displayed.

To reset the total driving time, contact the serv‐ ice center.

Analog Always Open Timer

The analog Always Open Timer indicates the hours and minutes that were driven with the convertible top open. A maximum of 6 hours and 59 minutes can be displayed.

The total driving time is displayed digitally in the tachometer.

1 Hours display LED

2 Minutes display

Settings and information

Operating concept

Some settings and information can only be cre‐ ated or opened while the ignition is switched on, the vehicle is standing, and the doors are closed.

1 Total driving time

2 Resetting

3 Current driving time

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 79

1 Button for:

▷ Selecting the display.

▷ Setting values.

▷ Confirming the selected display or set

values.

▷ Calling up computer information 74.

Symbol Function

Set the rain sensor, refer to page 68.

Displays

CONTROLS

Exiting displays

1. Press the button on the turn indicator lever

repeatedly until "HOME" is displayed.

2. Hold the button down.

The current speed is displayed again.

Displays are also exited if no entries are made within approx. 8 seconds.

Next setting or information

Open Check-Control, refer to page 81.

Exit the menu.

Within a setting or information display,

press the button on the turn indicator lever repeatedly until "NEXT" is displayed.

2. Hold the button down.

Direct change to the next setting or piece of in‐ formation.

Units of measure

The units of measure, such as for fuel consump‐ tion, route/distance, and temperature, can be

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 80

CONTROLS

Displays

changed. The settings are stored for the remote control currently in use.

1. "Settings"

2. "Language/Units"

3. Select the desired menu item.

4. Select the desired unit.

Clock

Setting the time

"Settings"

3. "Time:"

4. Turn the MINI joystick to set the hours and

press the MINI joystick.

5. Turn the MINI joystick to set the minutes

and press the MINI joystick.

The time is stored.

Setting the time format

"Settings"

2. "Time/Date"

3. "Format:"

4. Select the desired format.

The time format is stored.

The settings are stored for the remote control currently in use.

2. "Time/Date"

Setting the time zone

"Settings"

2. "Time/Date"

3. "Time zone:"

4. Turn the MINI joystick until the desired time

zone is displayed and press the MINI joy‐ stick.

The time zone is stored.

Date

Setting the date

"Settings"

2. "Time/Date"

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 81

Displays

CONTROLS

3. "Date:"

4. Turn the MINI joystick until the desired day

is displayed and press the MINI joystick.

5. Make the necessary settings for the month

and year.

The date is stored.

Setting the date format

1. "Settings"

2. "Time/Date"

3. "Format:"

4. Select the desired format.

The settings are stored for the remote control currently in use.

Settings on the Control Display

3. "Language:"

4. Select the desired language.

The setting is stored for the remote control cur‐ rently in use.

Setting the voice dialog

Voice dialog for the voice activation system, re‐ fer to page 25.

Brightness

The brightness is automatically adapted to the ambient lighting conditions. However, the basic setting can be changed when the low beams are switched on.

"Settings"

2. "Control display"

3. "Brightness"

Language

Setting the language

"Settings"

2. "Language/Units"

4. Turn the MINI joystick until the desired set‐

ting is selected.

5. Press the MINI joystick.

The setting is stored for the remote control cur‐ rently in use.

Depending on the light conditions, the bright‐ ness control may not be clearly visible.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 82

CONTROLS

Displays

Service requirements

The remaining driving distance and the date of the next scheduled service are displayed briefly immediately after you start the engine or switch on the ignition.

The current service requirements can be read out from the remote control by the service spe‐ cialist.

Detailed information on service requirements

More information on the scope of service re‐ quired can be displayed on the Control Display.

"Vehicle Info"

2. "Vehicle status"

Symbols

Symbols Description

No service is currently required.

The deadline for service or a le‐ gally mandated inspection is approaching.

The service deadline has al‐ ready passed.

Entering appointment dates

Enter the dates for the required inspections.

Make sure the date on the Control Display is set correctly.

"Vehicle Info"

2. "Vehicle status"

3. "Service required"

Required maintenance procedures and legally mandated inspections are displayed.

Additional information can be displayed on each entry:

Select the entry and press the MINI joystick.

To exit from the menu:

Move the MINI joystick to the left.

Online Edition for Part no. 01 40 2 961 056 - II/15

4. "§ Vehicle inspection"

5. Open the menu for entering the deadline.

6. "Date:"

Page 83

7. Create the settings.

8. Press the MINI joystick to apply the setting.

The year is highlighted.

9. Turn the MINI joystick to create the setting.

10. Press the MINI joystick to apply the setting.

The date entry is stored.

To exit from the menu:

Move the MINI joystick to the left.

Check Control

Displays

The symbol indicates that Check Control messages have been stored. The Check Control messages can be displayed later.

CONTROLS

The concept

The Check Control monitors vehicle functions and alerts you to any malfunctions in the sys‐ tems being monitored.

A Check Control message consists of indicator and warning lamps in the instrument cluster and, in some circumstances, an acoustic signal and text messages at the top of the Control Dis‐ play.

Indicator/warning lamps

The indicator and warning lamps can light up in a variety of combinations and colors in display area 1 or 2.

Several of the lamps are checked for proper functioning and light up temporarily when the engine is started or the ignition is switched on.

Text messages

Text messages at the upper edge of the Control Display in combination with a symbol in the in‐ strument cluster explain a Check Control mes‐ sage and the meaning of the indicator and warning lamps.

Supplementary text messages

Additional information, such as on the cause of a fault or the required action, can be called up via Check Control.

In urgent cases, this information will be shown as soon as the corresponding light comes on.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 84

CONTROLS

Displays

Hiding Check Control messages

Press the button on the turn indicator lever.

Some Check Control messages are displayed continuously and are not cleared until the mal‐ function is eliminated. If several malfunctions occur at once, the messages are displayed con‐ secutively.

They are marked with the symbol shown here.

Other Check Control messages are hidden au‐ tomatically after approx. 20 seconds. However, they are stored and can be displayed again later.

They are marked with the symbol shown here.

Viewing stored Check Control messages

The stored Check Control messages can only be displayed while the driver's door is closed.

1. Press the button on the turn indicator lever

repeatedly until "SET/INFO" is displayed.

2. Press and hold the button until the display

changes.

3. Press the button repeatedly until the corre‐

sponding symbol and "CHECK INFO" ap‐ pear on the display.

4. Press and hold the button.

If there is no Check Control message, this is indicated by "CHECK OK".

If a Check Control message has been stored, the corresponding message is dis‐ played.

The text message is also displayed on the Control Display.

5. Press the button to check for other mes‐

sages.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 85

Displaying on the Control Display

1. "Vehicle Info"

2. "Vehicle status"

3. "Check Control"

4. Select the text message.

Displays

CONTROLS

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 86

CONTROLS

Lamps

Vehicle equipment

When using the features and systems described here, adhere to local regulations.

At a glance

0 Lamps off / daytime running lights

1 Parking lights and daytime running lights

2 Low-beam headlights and welcome lights

3 Automatic headlight control, Adaptive Light

Control, daytime running lights, and wel‐ come lights

Parking lights/low beams, headlight con‐ trol

General information

When the driver's door is opened with the igni‐ tion switched off, the exterior lighting is auto‐

matically switched off when the light switch is in position 0, 2, or 3.

Switch on the parking lights if necessary, switch position 1.

Parking lights

Switch position 1: the vehicle lights light up on all sides.

Do not use the parking lights for extended peri‐ ods; otherwise, the battery may become dis‐ charged and it would then be impossible to start the engine.

When parking, it is preferable to switch on the one-sided roadside parking lights, refer to page 85.

Low beams

Switch position 2: the low beams are lit when the ignition is switched on.

Automatic headlight control

Switch position 3: the low beams are switched on and off automatically depending on the am‐ bient light, e.g., in tunnels, in twilight, or if there is precipitation. Adaptive Light Control is active.

A blue sky with the sun low on the horizon can cause the lights to be switched on.

The low beams remain switched on independ‐ ent of the ambient lighting conditions when you switch on the front fog lights.

Personal responsibility

The automatic headlamp control cannot serve as a substitute for your personal judg‐ ment in determining when the lamps should be switched on in response to ambient lighting conditions.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 87

Lamps

CONTROLS

For example, the sensors are unable to detect fog or hazy weather. To avoid safety risks, you should always switch on the lamps manually under these conditions.◀

The exterior lighting goes out automatically af‐ ter the vehicle is switched off.

High-beams/roadside parking lights

1 Turn signal/roadside parking light

2 Switching on the high-beams

3 Switching off the high-beams/headlight

flasher

To assist in parking, the vehicle can be illumi‐ nated on one side; note the country-specific regulations.

The roadside parking lights drain the battery. Therefore, do not leave them on for unduly long periods of time; otherwise, the battery might not have enough power to start the en‐ gine.

Switching on the roadside parking light

To switch on the roadside parking light on the left or right, press the turn indicator lever up or down after switching off the vehicle, arrow 1.

Daytime running lights

The daytime running lights light up in switch position 0, 1, or 3 when the ignition is switched on.

The exterior lighting goes out automatically af‐ ter the vehicle is switched off.

In switch position 1, the parking lights light up after the ignition is switched off.

Activating/deactivating

In some countries, driving with daytime run‐ ning lights is mandatory; for this reason, day‐ time running lights cannot be deactivated in these cases.

"Settings"

2. "Lighting"

3. "Daytime running lamps"

The setting is stored for the remote control cur‐ rently in use.

Welcome lights

If the light switch stays in switch position 2 or 3 after the vehicle is switched off, the parking lights and the interior lights light up for a cer‐ tain period when the vehicle is unlocked.

Switching off the roadside parking light

Press the lever up or down to the resistance point.

Online Edition for Part no. 01 40 2 961 056 - II/15

Headlight courtesy delay feature

The low beams stay lit for a short while after the ignition is switched off, if the lights are switched off and the headlight flasher is switched on.

Page 88

CONTROLS

Lamps

Setting the duration

1. "Settings"

2. "Lighting"

3. "Pathway light.: s"

4. Set the duration.

The setting is stored for the remote control cur‐ rently in use.

Adaptive Light Control

The concept

Adaptive Light Control is a variable headlight control system that enables dynamic illumina‐ tion of the road surface.

Depending on the steering angle and other pa‐ rameters, the light from the headlight follows the course of the road.

has failed. Have the system checked as soon as possible.

Fog lights

MINI Coupe, MINI Roadster

1 Fog lights

2 Rear fog light

To switch on/off, press the respective button.

MINI Convertible

Activating

With the ignition switch on, turn the light switch to position 3, refer to page 84.

To avoid blinding oncoming traffic, the Adap‐ tive Light Control does not swivel to the driver's side when the vehicle is at a standstill.

When driving in reverse, Adaptive Light Control is not active.

Malfunction

The warning light lights up. A message appears on the Control Display. Adap‐ tive Light Control is malfunctioning or

Online Edition for Part no. 01 40 2 961 056 - II/15

▷ To switch on the front fog lights:

Press the switch upward.

▷ To switch on the rear fog light:

Press the switch downward.

To switch off, press the respective switch up‐ ward or downward again.

Fog lights

The parking lights or low beams must be switched on. The green indicator lamp lights up when the front fog lights are switched on.

Page 89

Lamps

CONTROLS

Depending on the vehicle equipment, the front fog lights are switched off when the headlight flasher or the high-beams are activated.

If the automatic headlight control is activated, refer to page 84, the low beams are switched on automatically when the front fog lights are switched on.

Rear fog light

The low beams or parking lights with front fog lights must be switched on. The yellow indica‐ tor lamp lights up when the rear fog light is switched on.

Instrument lighting

The parking lights or low beams must be switched on to adjust the brightness. The brightness is increased to a certain limit and is then reduced again.

Switching interior lights on/off manually

To switch the interior lights on/off: press the switch.

If the interior lights are to remain switched off, press the switch for approx. 3 seconds.

Reading lights

▷ Press the button briefly: the brightness

changes in stages.

▷ Press and hold the button: the brightness

changes continuously.

Interior lights

The interior lights, the footwell lights and the cargo area light are controlled automatically.

To avoid draining the battery, all lights inside the vehicle are switched off some time after the ignition is switched off.

Online Edition for Part no. 01 40 2 961 056 - II/15

Switching the reading lights on/off

Press the switch.

MINI Roadster with semi-automatic convertible top

To switch on the interior lights: press the switch back.

Page 90

CONTROLS

To switch on the reading lights: press the switch forward.

To switch off, press the respective switch for‐ ward or back again.

Lamps

Ambient lighting

The color and brightness of the ambient light‐ ing can be changed.

Press the switch forward: the color changes in steps.

Press the switch back: the brightness changes in steps.

Intermediate settings and intermediate colors are possible.

For continuously changing colors of the ambi‐ ent lighting, press the switch forward for more than 10 seconds.

For Canadian vehicles:

Continuously changing colors of the ambient lighting is not available.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 91

Safety

CONTROLS

Vehicle equipment

When using the features and systems described here, adhere to local regulations.

Airbags

1 Front airbags

2 Side/head airbags in the seat backrests

Front airbags

Front airbags help protect the driver and front passenger by responding to frontal impacts in which safety belts alone cannot provide ade‐ quate restraint.

Combined side/head airbag

The combined side/head airbag supports the side of the body in the chest area and the head.

Protective action

Airbags are not triggered in every impact situa‐ tion, e.g., in less severe accidents or rear-end collisions.

Information on how to ensure the opti‐ mal protective effect of the airbags

▷ Keep at a distance from the airbags.

▷ Always grasp the steering wheel on the

steering wheel rim, holding your hands at the 3 o'clock and 9 o'clock positions, to keep the danger of injury to your hands or arms as low as possible if the airbag is trig‐ gered.

▷ There should be no people, animals, or ob‐

jects between an airbag and a person.

▷ Do not use the cover of the front airbag on

the front passenger side as a storage area.

▷ Keep the dashboard and window on the

front passenger side clear, i.e., do not cover with adhesive labels or coverings, and do not attach holders or cables such as for navigation instruments and mobile phones.

▷ Make sure that the front passenger is sitting

correctly, i.e., keeps his or her feet and legs in the footwell; otherwise, leg injuries can occur if the front airbag is triggered.

▷ Do not place slip covers, seat cushions or

other objects on the front passenger seat that are not approved specifically for seats with integrated side airbags.

▷ Do not hang pieces of clothing, such as

jackets, over the backrests.

▷ Make sure that occupants keep their heads

away from the side airbag and do not rest against the head airbag; otherwise, injuries can occur if the airbags are triggered.

▷ Do not remove the airbag restraint system.

▷ Do not remove the steering wheel.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 92

CONTROLS

Safety

▷ Do not apply adhesive materials to the air‐

bag cover panels, cover them or modify them in any way.

▷ Never modify either the individual compo‐

nents or the wiring in the airbag system. This also applies to steering wheel covers, the dashboard, the seats, the roof pillars and the sides of the headliner.◀

Even when all instructions are followed closely, injury from contact with the airbags cannot be ruled out in certain situations.

The ignition and inflation noise may lead to short-term and, in most cases, temporary hear‐ ing impairment in sensitive individuals.

In the case of a malfunction, deactivation and after triggering of the airbags

Do not touch the individual components imme‐ diately after the system has been triggered; otherwise, there is the danger of burns.

Only have the airbags checked, repaired or dis‐ mantled and the airbag generator scrapped by your service center or a workshop that has the necessary authorization for handling explo‐ sives.

Non-professional attempts to service the sys‐ tem could lead to failure in an emergency or undesired triggering of the airbag, either of which could result in injury.◀

Warning notices and information about the air‐ bags can also be found on the sun visors.

Automatic deactivation of the front passenger airbags

The occupation of the seat is detected by eval‐ uating the impression on the occupied seat sur‐ face of the front passenger seat.

The front and side airbags on the front passen‐ ger side are activated or deactivated accord‐ ingly by the system.

The indicator lamp above the interior rearview mirror, refer to page 91, shows the current status of the front passenger airbags, deacti‐ vated or activated.

Leave feet in the footwell

Make sure that the front passenger keeps his or her feet in the footwell; otherwise, the front passenger airbags may not function prop‐ erly.◀

Child restraint fixing system in the front

passenger seat

Before transporting a child on the front passen‐ ger seat, read the safety and operating instruc‐ tions under Transporting children safely, refer to page 59.◀

Malfunction of the automatic deactivation system

When transporting older children and adults, the front passenger airbags may be deactivated in certain sitting positions. In this case, the indi‐ cator lamp for the front passenger airbags lights up.

In this case, change the sitting position so that the front passenger airbags are activated and the indicator lamp goes out.

If it is not possible to activate the airbags, have the person sit in the rear.

To make sure that occupation of the seat cush‐ ion can be detected correctly:

▷ Do not attach seat covers, seat cushion

padding, ball mats, or other items to the front passenger seat unless they are specifi‐ cally recommended by the manufacturer of your MINI.

▷ Do not place electronic devices on the pas‐

senger seat if a child restraint fixing system is mounted on the seat.

▷ Do not place objects under the seat that

could press against the seat from below.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 93

Safety

CONTROLS

Indicator light for the front passenger airbags

The indicator lamp for the front passenger air‐ bags indicates the operating state of the front passenger airbags.

The light indicates whether the airbags are acti‐ vated or deactivated.

▷ The indicator lamp lights up

when a child in a child re‐ straint fixing system in‐ tended for the purpose is properly detected on the seat. The airbags on the front passenger side are not acti‐ vated.

▷ The indicator lamp does not light up when,

for example, a correctly seated person of sufficient size is detected on the seat. The airbags on the front passenger side are ac‐ tivated.

▷ The indicator lamp does not light up when

the seat is empty. However, the airbags on the front passenger side are not activated.

Most child seats are detected by the system. Especially the child seats required by NHTSA at the time that the vehicle was manufactured. After installing a child seat, make sure that the indicator lamp for the front passenger airbags lights up. This indicates that the child seat has been detected and the front passenger airbags are not activated.

Operational readiness of airbag system

In the radio ready state and beyond, re‐ fer to page 64, the warning light lights

up briefly to indicate that the entire air‐ bag system and the belt tensioners are opera‐ tional.

Airbag system malfunction

▷ Warning light does not light up in the radio

ready state.

▷ Warning light remains permanently on.

Have the airbag system checked without delay if there is a malfunction

In the event of a malfunction in the airbag sys‐ tem, have it checked without delay; otherwise, there is the risk that the system will not func‐ tion as intended even if a sufficiently severe ac‐ cident occurs.◀

MINI Convertible: roll‐ over protection system

The rollover protection system is automatically activated in a sufficiently severe accident or when the inclination of the longitudinal axis is extremely high. The protective bars behind the rear head restraints extend within fractions of a second.

The rollover protection system increases the safety of the vehicle occupants in addition to the reinforced windshield frame.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 94

CONTROLS

Safety

Do not obstruct the area of movement

Always keep the area of movement of the rollover protection system clear. In light acci‐ dents, you are protected by the fastened safety belt and, depending on the severity of the acci‐ dent, the belt tightener and the multi-level air bag restraint system.◀

Lowering

Have the service center check the rollover pro‐ tection system after it is deployed unexpect‐ edly.

General instructions on the rollover pro‐

tection system

When the rollover protection system is ex‐ tended, do not move the convertible top under any circumstances.

Do not modify the individual components of the rollover protection system or the wiring in any way.

Work on the rollover protection system should only be performed by a MINI service center.

Non-professional work on the system could lead to failure or a malfunction.

To check the system and to ensure that the sys‐ tem will operate properly over the long-term, it is imperative that you adhere to the specified service intervals.◀

Functional requirements

The system must have been initialized when the tire inflation pressure was correct; other‐ wise, reliable signaling of a flat tire is not en‐ sured.

Initialize the system after each correction of the tire inflation pressure and after every tire or wheel change.

System limits

Sudden tire damage

Sudden serious tire damage caused by external influences cannot be indicated in ad‐ vance.◀

A natural, even pressure loss in all four tires cannot be detected. Therefore, check the tire inflation pressure regularly.

The system could be delayed or malfunction in the following situations:

▷ When the system has not been initialized.

▷ When driving on a snowy or slippery road

surface.

▷ Sporty driving style: slip in the drive wheels,

high lateral acceleration.

▷ When driving with snow chains.

When the vehicle is driven with a compact wheel, refer to page 249, the Flat Tire Monitor is not functional.

FTM Flat Tire Monitor

The concept

The system does not measure the actual infla‐ tion pressure in the tires.

The system detects a pressure loss in a tire by comparing the rotational speeds of the individ‐ ual wheels while moving.

In the event of a pressure loss, the diameter and therefore the rotational speed of the corre‐ sponding wheel change. This is detected and reported as a flat tire.

Online Edition for Part no. 01 40 2 961 056 - II/15

Status display

The current status of the Flat Tire Monitor can be displayed on the Control Display, e.g., whether or not the FTM is active.

"Vehicle Info"

2. "Vehicle status"

Page 95

Safety

CONTROLS

3. "Flat Tire Monitor"

The status is displayed.

Initialization

The initialization process adopts the set infla‐ tion tire pressures as reference values for the detection of a flat tire. Initialization is started by confirming the inflation pressures.

Do not initialize the system when driving with snow chains.

"Vehicle Info"

2. "Vehicle status"

3. "Reset"

Indication of a flat tire

The warning lights come on in yellow and red. A message appears on the Control Display. In addition, a signal sounds.

There is a flat tire or a major loss in tire inflation pressure.

1. Reduce your speed and stop cautiously.

Avoid sudden braking and steering maneu‐ vers.

2. Check whether the vehicle is fitted with

regular tires or run-flat tires.

Run-flat tires, refer to page 230, are la‐ beled with a circular symbol containing the letters RSC marked on the tire sidewall.

Do not continue driving without run-flat tires

Do not continue driving if the vehicle is not equipped with run-flat tires; continued driving may result in serious accidents.◀

When a flat tire is indicated, DSC Dynamic Sta‐ bility Control is switched on if necessary.

Actions in the event of a flat tire

4. Start the engine, but do not start driving.

5. Start the initialization with "Reset".

6. Drive away.

The initialization is completed while driving, which can be interrupted at any time. The initi‐ alization automatically continues when driving resumes.

Online Edition for Part no. 01 40 2 961 056 - II/15

Normal tires

Identify the damaged tire.

Do this by checking the inflation pressure in all four tires.

The tire pressure gauge of the Mobility Sys‐ tem, refer to page 231, can be used for this purpose.

If the tire inflation pressure in all four tires is correct, the Flat Tire Monitor may not have been initialized. In this case, initialize the system.

If an identification is not possible, please contact the service center.

Rectify the flat tire using the Mobility Sys‐

tem, refer to page 231, or replace the damaged wheel, refer to page 248.

Page 96

CONTROLS

Safety

Run-flat tires

You can continue driving with a damaged tire at speeds up to 50 mph/80 km/h.

Continued driving with a flat tire

If continuing to drive with a damaged tire:

1. Avoid sudden braking and steering maneu‐

vers.

2. Do not exceed a speed of 50 mph/80 km/h.

3. At the next opportunity, check the inflation

pressure in all four tires.

If the tire inflation pressure in all four tires is correct, the Flat Tire Monitor may not have been initialized. In this case, initialize the system.

Possible driving distance with complete loss of tire inflation pressure:

The possible driving distance after a loss of tire inflation pressure depends on the cargo load and the driving style and conditions.

For a vehicle containing an average load, the possible driving distance is ap‐ prox. 50 miles/80 km.

When the vehicle is driven with a damaged tire, its handling characteristics change, e.g., re‐ duced lane stability during braking, a longer braking distance, and altered self-steering properties. Adjust your driving style accord‐ ingly. Avoid abrupt steering maneuvers or driv‐ ing over obstacles, e. g., curbs, potholes, etc.

Because the possible driving distance depends on how the vehicle is used during the trip, the actual distance may be smaller or greater de‐ pending on the driving speed, road conditions, external temperature, cargo load, etc.

Continued driving with a flat tire

Drive moderately and do not exceed a

speed of 50 mph/80 km/h.

A loss of tire inflation pressure results in a change in the handling characteristics, e.g., re‐ duced lane stability during braking, a longer braking distance and altered self-steering prop‐ erties.◀

Final tire failure

Vibrations or loud noises while driving can indicate the final failure of the tire. Reduce speed and stop; otherwise, pieces of the tire could come loose and cause an accident. Do not continue driving, and contact your service center.◀

Tire Pressure Monitor TPM

The concept

The system monitors the tire pressure in the four mounted tires. The system notifies you if there is a significant loss of pressure in one or more tires. Sensors in the tire valves measure the tire pressure.

Notes

Tire damage caused by external influen‐

ces

Sudden tire damage caused by external influ‐ ences cannot be indicated in advance.◀

To operate the system, also note the additional information and instructions contained under Tire inflation pressure, refer to page 220.

Functional requirements

The system must have been reset while the in‐ flation pressure was correct; otherwise, it may not reliably signal a loss in pressure.

Perform a system reset after adjusting the tire inflation pressure to a new value and after changing a tire or wheel

Always use wheels with TPM electronics to en‐ sure that the system will operate properly.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 97

Safety

CONTROLS

Status display

The current status of the Tire Pressure Monitor TPM can be displayed on the Control Display, e.g., whether or not the TPM is active.

1. "Vehicle Info"

2. "Vehicle status"

3. "Tire Pressure Monitor - TPM"

The status is displayed.

Status display

The tire and system status is indicated on the Control Display by the color of the tires and a text.

All wheels are green

The system is active and issues warnings based on the tire inflation pressures stored during the last reset.

One wheel is yellow

A flat tire or major drop in inflation pressure in the indicated tire.

All wheels are yellow

A flat tire or major drop in inflation pressure in several tires.

Wheels, gray

The system cannot detect a flat tire.

Reasons for this may be:

▷ The system is being reset.

▷ Malfunction.

Performing a reset

Perform a system reset after adjusting the tire inflation pressure to a new value and after changing a tire or wheel.

1. "Vehicle Info"

2. "Vehicle status"

3. "Reset"

4. Start the engine - do not drive away.

5. Start the initialization with "Reset".

6. Drive away.

The wheels are shown in gray and the status is displayed.

After a short trip at over 20 mph/30 km/h, the set tire inflation pressures are adopted as tar‐ get values. The reset is completed automati‐ cally as you drive.

After a successful reset, the wheels appear in green on the Control Display and "Status: TPM active" is displayed.

The trip can be interrupted at any time. When driving resumes, the reset is continued auto‐ matically.

Low tire pressure message

The warning lights come on in yellow and red. A Check Control message is displayed. A message is displayed on the onboard monitor. In addition, a sig‐

nal sounds.

▷ There is a flat tire or substantial loss of infla‐

tion pressure on the indicated wheel.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 98

CONTROLS

Safety

▷ The system was not reset after a wheel

change and thus issues warnings based on the inflation pressures initialized last.

1. Reduce your speed and stop cautiously.

Avoid sudden braking and steering maneu‐ vers.

2. Check whether the vehicle is fitted with

regular tires or run-flat tires.

Run-flat tires, refer to page 230, are la‐ beled on the tire sidewall with a circular symbol containing the letters RSC.

Do not continue driving without run-flat tires

Do not continue driving if the vehicle is not equipped with run-flat tires; continued driving may result in serious accidents.◀

When a low inflation pressure is indicated, DSC Dynamic Stability Control is switched on if nec‐ essary.

Actions in the event of a flat tire

Normal tires

Identify the damaged tire.

Do this by checking the air pressure in all four tires. The tire pressure gauge of the Mobility System, refer to page 231, can be used for this purpose.

If the tire inflation pressure in all four tires is correct, the Tire Pressure Monitor may not have been reset. Reset the system.

If an identification is not possible, please contact the service center.

2. Rectify the flat tire using the Mobility Sys‐

tem, refer to page 231, or replace the damaged wheel, refer to page 248.

Use of tire sealant, e.g., the Mobility Sys‐ tem, may damage the TPM wheel electron‐ ics. In this case, have the electronics checked at the next opportunity and have them replaced if necessary.

Run-flat tires

You can continue driving with a damaged tire at speeds up to 50 mph/80 km/h.

Do not continue driving without run-flat tires

Do not continue driving if the vehicle is not equipped with run-flat tires; continued driving may result in serious accidents.◀

Continued driving with a flat tire

If continuing to drive with a damaged tire:

1. Avoid sudden braking and steering maneu‐

vers.

2. Do not exceed a speed of 50 mph/80 km/h.

3. Check the air pressure in all four tires at the

next opportunity.

If the tire inflation pressure in all four tires is correct, the Tire Pressure Monitor may not have been reset. Reset the system.

Possible driving distance with complete loss of tire inflation pressure:

The possible driving distance after a loss of tire inflation pressure depends on the cargo load and the driving style and conditions.

For a vehicle containing an average load, the possible driving distance is ap‐ prox. 50 miles/80 km.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 99

Safety

CONTROLS

Continued driving with a flat tire

Drive moderately and do not exceed a

speed of 50 mph/80 km/h.

Final tire failure

Message indicating that the inflation pressure needs to be checked

The yellow warning light lights up.

A Check Control message is displayed.

An additional message is displayed on

the onboard monitor.

▷ The system has detected that a wheel was

changed but a reset was not performed.

▷ The tire was not inflated according to speci‐

fications.

▷ The tire pressure has dropped since the last

confirmation.

In this case:

▷ Check the tire inflation pressure and correct

it if necessary.

▷ After changing a wheel, reset the system.

System limits

The system will not function properly if a reset was not performed, e.g., it may identify a tire as flat although the tire is filled to the correct infla‐ tion pressure.

The tire pressure depends on the temperature of the tire. An increase in the tire temperature, e.g., while driving or due to sunlight, increases

the tire inflation pressure. The tire pressure de‐ creases when the tire temperature drops. In case of severe temperature drops, this behavior may lead to a warning on account of the de‐ fined warning limits.

Malfunction

The yellow warning light flashes yellow and then lights up continuously.

A Check Control message is displayed.

An additional message is displayed on

the onboard monitor.

A flat tire or tire inflation pressure loss cannot be detected.

Display in the following situations:

▷ A wheel without TPM electronics is

mounted, e.g., a compact wheel:

Have the system checked by the service center if necessary.

▷ Malfunction:

Have the system checked by the service center.

▷ TPM was unable to complete the reset.

Reset the system again.

The yellow warning light flashes and then lights up continuously.

A Check Control message is displayed.

An additional message is displayed on

the onboard monitor.

A flat tire or tire inflation pressure loss cannot be detected.

Display in the following situation:

▷ Disturbance by other systems or devices

with the same radio frequency:

After leaving the area of the disturbance, the system automatically becomes active again.

Online Edition for Part no. 01 40 2 961 056 - II/15

Page 100

CONTROLS

Safety

Declaration according to NHTSA/FMVSS 138 Tire Pressure Monitoring Systems

Each tire, including the spare (if provided) should be checked monthly when cold and in‐ flated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.).

As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pres‐ sure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pres‐ sure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel ef‐ ficiency and tire tread life, and may affect the vehicle's handling and stopping ability.

Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.

Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approxi‐ mately one minute and then remain continu‐ ously illuminated. This sequence will continue upon subsequent vehicle startups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as in‐ tended. TPMS malfunctions may occur for a va‐ riety of reasons, including the installation of re‐ placement or alternate tires or wheels on the

vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the re‐ placement or alternate tires and wheels allow the TPMS to continue to function properly.

Speed limit

The concept

Enter a speed for which a Check Control mes‐ sage will be displayed when the speed is reached. This enables you to receive warnings if you exceed a speed limit in an urban area, for example.

You are only warned of reaching this speed a second time if your vehicle speed falls below it again by at least 3 mph/5 km/h.

Displaying, setting or changing the limit

"Settings"

2. "Speed"

3. "Warning at:"

4. Turn the MINI joystick to accept the setting.

5. Press the MINI joystick to apply the setting.

The limit is stored.

Applying your current speed as the limit

"Settings"

2. "Speed"

Online Edition for Part no. 01 40 2 961 056 - II/15

MINI Convertible 2015, Coupe Roadster Convertible 2015 Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Cockpit

Vehicle equipment

All around the steering wheel

Displays

Indicator/warning lights

All around the center console

All around the shift/ selector lever

Onboard monitor

Vehicle equipment

The concept

Control elements at a glance

Operating concept

Example: setting the clock

Status information

Entering letters and numbers

Voice activation system

Vehicle equipment

The concept

Using voice activation

Requirements

Possible commands

Example: playing back a CD

Setting the voice dialog

Adjusting the volume

Opening and closing

Vehicle equipment

Remote control/key

Personal Profile

Central locking system

Opening and closing: from the outside

Opening and closing: from the inside

Tailgate

Comfort Access

Alarm system

Power windows

MINI Convertible: wind deflector

MINI Roadster: manual convertible top

Adjusting

Vehicle equipment

Sitting safely

Seats

Safety belts

Head restraints

Mirrors

Steering wheel

Transporting children safely

Vehicle equipment

MINI Convertible: LATCH child restraint fixing system

Driving

Vehicle equipment

Ignition lock

Start/Stop button

Starting the engine

Engine stop

Parking brake

Turn signal, high-beams, headlight flasher

Washer/wiper system

Washer fluid

Steptronic transmission

Manual transmission

Displays

Vehicle equipment

Tachometer

Coolant temperature

Fuel gauge

Computer

Always Open Timer

Settings and information

Units of measure

Clock

Date

Settings on the Control Display

Service requirements

Check Control

Lamps

Vehicle equipment