Minarik Drives XL SERIES Catalog Page

Drives for DC Brushed Motors

2

4

05C

105

205C

S

C

G

FU501

05CI105C

1S

2

3S

305C

105

C

S

1

05

1

C

2C

305

C

3

05

05

1

205

105

U

C

R

05

B1

1

05

Q052

105

]

[

]

[6]

[

]

0

1Q PWM

UL

Field

Supply

(VDC)

****

Rec.

CSA

Drive

Input

Voltage

(VAC)

Output

Voltage Range

(VDC)

Max.

Armature

Current

HP Rating @
90/130 VDC

Output

HP Rating @

180/240 VDC

Output

Enclosure

Reversing

*****

Isolation

***

XL3025A 115 / 230 0-130 / 0-240 3 1/20 - 1/4 1/10 - 1/2 CHASSIS – – YES YES YES –

C4XL3025 115 / 230 0-130 / 0-240 3 1/20 - 1/4 1/10 - 1/2 NEMA 4X – – YES – – –

XL3050A 115 / 230 0-130 / 0-240 5 1/8 - 1/2 1/4 - 1 CHASSIS – – YES YES YES –

XL3200A 115 / 230 0-130 / 0-240 10** 1/4 - 1 1/2 - 2 CHASSIS – – YES YES YES –

C4XL3200A 115 / 230 0-130 / 0-240 10 1/4 - 1 1/2 - 2 NEMA 4X – – YES – – –

XL3300A 115 / 230 0-130 / 0-240 15 1/4 - 1 1/2 1/2 - 3 CHASSIS – – YES YES YES –

** Heat sink number 223-0271 must be used when the output is above 5 amps.
*** Built in isolation is not available on the XL series. Minarik Drives recommends using the PCMXP (Pg 13), MMXL-PCM (Pg 14), or PCM4 (Pg 42)
**** The field supply is rated at 1 amp. A 50/100 VDC field is available with 115 VAC input and a 100/200 VDC field is available with 230 VAC input.
***** See regenerative drives in Section D for PWM drives that can reverse on-the-fly.

XL3025A, XL3050A & XL3200A DIMENSIONS

Minarik Drives’ XL Series of pulse-width-modulated
(PWM) variable-speed DC drives provide exceptional

R

B

230 230

621[79.4

01

31.4

5

HEIGHT

XL3025A 2.25 [57]

XL3050A 3.00 [76]

XL3200A 3.75 [95]

Q

05

HT1

A

A

T1

W50

SW50

I 2

FA

T-A

TIN

BT

R

I

IBIHNI

LI

S

0 52.

1

83.5

73

All dimensions in inches [millimeters]

Dimensions of drives not shown above can be

found on pages 55 and 57.

Wiring diagrams can be found on pages 65 and 66.

19 [5]

D

B2

1

R

205R

R

LI

.

0.50 [13]

performance. They output nearly pure DC power to
brush-type motors ranging from 1/20 to 3 HP. Drives
accept 115 or 230 VAC input to output 0 to 130 or
240 VDC, respectively.

MOSFET power devices switch at a high frequency
above the audible range, to provide fast circuit re­sponse and a constant 1.05 form factor over the
entire 100:1 speed range. Highly-efficient XL drives
provide cool, quiet motor operation with extended
brush life and low maintenance. For convenience,
the drives have a cage-clamp terminal block to
make wiring easy. The XL3300A can jog motors
from 0 -120% of rated speed with a separate trim­mer pot.

See page 51 for an in-depth comparison of the dif­ferent 1Q PWM drives.

CE

TUV

B

FEATURES

• Speedrange,regulation,&formfactor: 1% of base speed regulation with a

100:1 speed range and a 1.05 form factor over the entire range.

• User adjustable calibration pots: Minimum Speed, Maximum Speed,

Current Limit, IR Compensation, Acceleration, Deceleration and Jog (XL3300A
and C4XL3200A only).

• DiagnosticLEDs: LEDs for power and current limit status.

• Stoppingmode: Inhibit (N.O.) for coasting to a stop on all models.

• Cageclampterminalblock:Quick and easy wire terminations reduce instal-

lation time!

• Additionalfeatures: Dual voltage AC input, DC field supply, on board line

fuse, and jog mode on C4XL3200A and XL3300A.

• Accessories: Heatsink 223-0271. 201-0024 inhibit plug with 18” leads,

DLC600 digital closed loop controller.

• RoHS: All XL series models are RoHS compliant.

•XLSERIES

Call us toll free 1.800.MINARIK or find more information online at www.minarikdrives.com

XL3025A
XL3050A
XL3200A

XL3300A

C4XL3025

C4XL3200A

15