Minarik Drives MM23000D SERIES Catalog Page

Drives for DC Brushed Motors

1Q SCR

A

CSA

CE

TUV

UL

Drive

MM23012D 115 / 230 0-90 / 0-180 1.5 1/20 - 1/8 1/10 - 1/4 CHASSIS – – – YES YES Pending

MM23112D 115 / 230 0-90 / 0-180 1.5 1/20 - 1/8 1/10 - 1/4 NEMA 1 – – – YES YES Pending

MM23212D 115 / 230 0-90 / 0-180 1.5 1/20 - 1/8 1/10 - 1/4 NEMA 1 YES – – YES YES Pending

MM23412D 115 / 230 0-90 / 0-180 1.5 1/20 - 1/8 1/10 - 1/4 NEMA 4X – – – YES YES Pending

MM23002D 115 / 230 0-90 / 0-180 10* 1/8 - 1 1/4 - 2 CHASSIS – – – YES YES Pending

MM23102D 115 / 230 0-90 / 0-180 10** 1/8 - 1 1/4 - 2 NEMA 1 – – – YES YES Pending

MM23202D 115 / 230 0-90 / 0-180 10** 1/8 - 1 1/4 - 2 NEMA 1 YES – – YES YES Pending

MM23402D 115 / 230 0-90 / 0-180 10 1/8 - 1 1/4 - 2 NEMA 4X – – – YES YES Pending

***** Heat sink number 223-0159 must be used when the output is above 5 amps.
***** Heat sink number 223-0174 must be used when the output is above 5 amps.
***** Built in isolation is not available on the MM23000D series. Minarik Drives recommends using the MM-PCM (Pg 8), PCM20000A (Pg 9), MM300 (Pg 10), or PCM4 (Pg 42).
***** The field supply is not available on the MM23000D series. Minarik Drives recommends using the MM23000C series (Pg 4).
***** Reversing models are designed for dynamic braking and reversing using the switches on the enclosure. See regenerative drives in Section C for SCR drives that can reverse on-the-fly or

***** for drives with the ability to remote mount direction and braking switches.

Input

Voltage

(VAC)

Output

Voltage Range

(VDC)

Max.

Armature

Current

HP Rating @

90 VDC

Output

HP Rating @

180 VDC

Output

Enclosure

Reversing

*****

Isolation

***

Field

Supply

(VDC)

****

Listed

MM23002D & MM23012D DIMENSIONS

The MM23000D Series is similar to the MM23000C
Series except for the addition of the following fea­tures. The MM23000D Series has a flexible inhibit

0.75 [19]

0.19 [5]

circuit that can be set for a normally open or nor­mally closed input. A torque mode option was also

3.58 [91]

1.75 [44]

added to this family of drives where the drive will
control the current to the motor, perfect for ten­sion control applications. The logic circuit in the
MM23000D Series contains additional filtering that
allows the drive to run better and longer in electri-

0.74 [19]

0.64 16]

cally noisy environments. Also the MM23000D Se­ries can accept a 5K or 10K Ohm potentiometer
and that allows the drive to be a drop in replace-

3.50 [97]

4.30 [109]

Height: 1.60 [41]

All dimensions in inches [millimeters]

Dimensions of drives not shown above can be found on page 55.

Wiring diagrams can be found on pages 61 and 62.

ment for many competitor drives.

Choose the MM23000D Series for the best value
single quadrant SCR drive on the market.

See page 50 for an in-depth comparison of the dif­ferent 1Q SCR drives.

FEATURES

• MMfootprint: Chassis drives have a compact industry standard footprint.

• Speedrange,regulation&formfactor:1% of base speed regulation with a

60:1 speed range and a 1.37 form factor at maximum rated voltage.

• User adjustable calibration pots: Minimum Speed, Maximum Speed,

Current Limit, IR Compensation, Acceleration and Deceleration.

• DiagnosticLEDs: LEDs for power and current limit status.

• Stoppingmodes: Coast to minimum speed or to stop with selectable N.O. or

N.C. inhibit contacts. Dynamic braking included on MM232x2D.

• Spadeandscrewterminals: Easy to use spade terminals on chassis; screw

terminals on enclosed units.

• SpeedorTorquecontrol: Choose operating mode using jumper pins.

• Accessories: Heatsink 223-0159 or 223-0174. 201-0024 inhibit plug with

18” leads, DLC600 digital closed loop controller, PCM4 isolation card.

• RoHS: All MM23000D series models are RoHS compliant.

•MM23000DSERIES

Call us toll free 1.800.MINARIK or find more information online at www.minarikdrives.com

MM23002D
MM23012D

MM23202D
MM23212D

MM23102D
MM23112D

MM23402D
MM23412D

5