Milwaukee 18 VOLT CIRCULAR SAW User Manual
Catalog No.
No de Cat.
Catálogo No.
6310-20
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
SPECIAL NOTE: New battery packs are not fully charged.
Charge your battery pack before using it for the first time and
follow the charging instructions in your charger manual.
NOTE SPÉCIALE : Les batteries neuves ne sont pas
entièrement chargées. Chargez la batterie avant de vous en
servir la première fois en suivant les instructions de recharge
18 VOLT CIRCULAR SAW
SCIE CIRCULAIRE 18V
dans le manuel qui accompagne cet outil.
NOTA ESPECIAL: Las batterias, cuando son nuevas, no
están totalmente cargadas. Cargue su bateria antes de
usarla por primera vez siga las instrucciones de carga que
vienen en el manuel de la herramienta.
SIERRA CIRCULAR DE 18V
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S MANUAL.
AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN COMPRENDRE LE
MANUEL DE L'UTILISATEUR.
PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL MANUAL DEL
OPERADOR.
page 2
GENERAL SAFETY RULES — FOR ALL BATTERY OPERATED TOOLS
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below, may result in electric shock,
fire and/or serious personal injury.
SA VE THESE INSTRUCTIONS
WORK AREA
1. Keep your work area clean and well lit. Cluttered benches and
dark areas invite accidents.
2. Do not operate power tools in explosive atmospheres, such
as in the presence of flammable liquids, gases, or dust.
Power tools create sparks which may ignite the dust or fumes.
3. Keep bystanders, children, and visitors away while operat-
ing a power tool. Distractions can cause you to lose control.
Protect others in the work area from debris such as chips and
sparks. Provide barriers or shields as needed.
ELECTRICAL SAFETY
4. Do not abuse the cord. Never use the cord to carry the tool.
Keep cord away from heat, oil, sharp edges, or moving parts.
Replace damaged cords immediately. Damaged cords may
create a fire.
5. A battery operated tool with integral batteries or a separate
battery pack must be recharged only with the specified
charger for the battery. A charger that may be suitable for one
type of battery may create a risk of fire when used with another
battery.
6. Use battery operated tool only with specifically designated
battery pack. Use of any other batteries may create a risk of fire.
PERSONAL SAFETY
7. Stay alert, watch what you are doing, and use common sense
when operating a power tool. Do not use tool while tired or
under the influence of drugs, alcohol, or medication. A mo-
ment of inattention while operating power tools may result in serious
personal injury.
8. Dress properly. Do not wear loose clothing or jewelry. Con-
tain long hair. Keep your hair, clothing, and gloves away from
moving parts. Loose clothes, jewelry, or long hair can be caught in
moving parts.
9. Avoid accidental starting. Be sure switch is in the locked or
off position before inserting battery pack. Carrying tools with
your finger on the switch or inserting the battery pack into a tool
with the switch on invites accidents.
10. Remove adjusting keys or wrenches before turning the
tool on. A wrench or a key that is left attached to a rotating part of
the tool may result in personal injury.
11. Do not overreach. Keep proper footing and balance at all
times. Proper footing and balance enable better control of the tool
in unexpected situations.
12. Use safety equipment. Always wear eye protection. Dust
mask, non-skid safety shoes, hard hat, or hearing protection must
be used for appropriate conditions.
TOOL USE AND CARE
13. Use clamps or other practical way to secure and support
the workpiece to a stable platform. Holding the work by hand
or against your body is unstable and may lead to loss of control.
14. Do not force tool. Use the correct tool for your application.
The correct tool will do the job better and safer at the rate for which
it is designed.
15. Do not use tool if switch does not turn it on or off. A tool that
cannot be controlled with the switch is dangerous and must be
repaired.
16. Disconnect battery pack from tool or place the switch in the
locked or off position before making any adjustments,
changing accessories, or storing the tool. Such preventive
safety measures reduce the risk of starting the tool accidentally.
17. Store idle tools out of reach of children and other untrained
persons. Tools are dangerous in the hands of untrained users.
18. When battery pack is not in use, keep it away from other
metal objects like: paper clips, coins, keys, nails, screws,
or other small metal objects that can make a connection
from one terminal to another. Shorting the battery terminals
together may cause sparks, burns, or a fire.
19. Maintain tools with care. Keep cutting tools sharp and clean.
Properly maintained tools with sharp cutting edge are less likely to
bind and are easier to control.
20. Check for misalignment or binding of moving parts, break-
age of parts, and any other condition that may affect the
tool’s operation. If damaged, have the tool serviced before
using. Many accidents are caused by poorly maintained tools. Do
not use a damaged tool. Tag damaged tools “Do not use” until
repaired.
21. Use only accessories that are recommended by the manu-
facturer for your model. Accessories that may be suitable for
one tool may create a risk of injury when used on another tool.
SERVICE
22. Tool service must be performed only by qualified repair
personnel. Service or maintenance performed by unqualified per-
sonnel may result in a risk of injury.
23. When servicing a tool, use only identical replacement parts.
Follow instructions in the Maintenance section of this
manual. Use of unauthorized parts or failure to follow Maintenance
Instructions may create a risk of shock or injury.
page 3
SPECIFIC SAFETY RULES — CIRCULAR SAWS
1. Maintain labels and nameplates. These carry important information. If unreadable or missing, contact a
replacement.
2. DANGER! Keep hands away from cutting area and blade. Keep your second hand on auxiliary handle or motor housing. If both
hands are holding the saw, they cannot be cut by the blade.
Keep your body positioned to either side of the saw blade, but not in line with the saw blade. KICKBACK could cause the saw to jump
backwards (See “Causes and Operator Prevention of KICKBACK” below).
Do not reach underneath the work. The guard can not protect you from the blade below the work.
3. Check lower guard for proper closing before each use. Do not operate saw if lower guard does not move freely and close
instantly. Never clamp or tie the lower guard into the open position. If saw is accidentally dropped, lower guard may be bent. Raise the
lower guard with the lower guard lever and make sure it moves freely and does not touch the blade or any other part, in all angles and depths of
cut.
4. Check the operation and condition of the lower guard spring. If the guard and the spring are not operating properly, they must
be serviced before use. Lower guard may operate sluggishly due to damaged parts, gummy deposits, or a buildup of debris.
5. Lower guard should be retracted manually only for special cuts such as “Pocket Cuts” and “Compound Cuts”. Raise lower
guard by lower guard lever. As soon as blade enters the material, lower guard must be released. For all other sawing, the lower
guard should operate automatically.
6. Always observe that the lower guard is covering the blade before placing saw down on bench or floor. An unprotected, coasting
blade will cause the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch is
released.
7. NEVER hold piece being cut in your hands or across your leg. It is important to support the work properly to minimize body exposure, blade
binding, or loss of control.
8. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its
own cord. Contact with a “live” wire will also make exposed metal parts of the tool “live” and shock the operator.
9. When ripping always use a rip fence or straight edge guide. This improves the accuracy of cut and reduces the chance for blade binding.
10. Always use blades with correct size and shape (diamond vs. round) arbor holes. Blades that do not match the mounting hardware of
the saw will run eccentrically, causing loss of control.
11. Never use damaged or incorrect blade washers or bolts. The blade washers and bolts were specially designed for your saw, for optimum
performance and safety of operation.
12. WARNING! Use of this tool can generate dust containing chemicals known to cause cancer, birth defects or other reproductive harm. Use
appropriate respiratory protection.
13. Causes and Operator Prevention of KICKBACK:
KICKBACK is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece
toward the operator.
When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward
the operator.
If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the
blade to climb out of the kerf and jump back toward operator.
MILWAUKEE
service facility for a free
KICKBACK is the result of tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as
given below:
14. Maintain a firm grip with both hands on the saw and position your body and arm to allow you to resist KICKBACK forces.
KICKBACK forces can be controlled by the operator, if proper precautions are taken.
15. When blade is binding, or when interrupting a cut for any reason, release the trigger and hold the saw motionless in the
material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward
while the blade is in motion or KICKBACK may occur. Investigate and take corrective actions to eliminate the cause of blade binding.
16. When restarting a saw in the workpiece, center the saw blade in the kerf and check that saw teeth are not engaged into the
material. If saw blade is binding, it may walk up or KICKBACK from the workpiece as the saw is restarted.
17. Support large panels to minimize the risk of blade pinching and KICKBACK. Large panels tend to sag under their own weight. Supports
must be placed under the panel on both sides, near the line of cut and near the edge of the panel.
18. Do not use dull or damaged blade. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and
KICKBACK.
19. Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting,
it may cause binding and KICKBACK.
20. Use extra caution when making a “Pocket Cut” into existing walls or other blind areas. The protruding blade may cut objects that can
cause KICKBACK.
page 4
Symbology
Specifications
Properly Recycle Nickel Cadmium
Batteries
Volts Direct Current
No Load Revolutions per Minute
Underwriters Laboratories, Inc.
1. Lock-off button
2. Trigger
3. Handle
4. Battery
5. Battery pack release buttons
6. Shoe
7. Lower guard lever
8. Lower guard
9. Blade bolt
10. Blade flange
11. Blade
12. Sight line
13. Rip fence slot
14. Rip fence adjusting knob
15. Upper guard
16. Front handle
17. Depth setting gauge
18. Wrench
19. Spindle lock button
20. Depth adjusting lever
21. Bevel adjusting knob
22. Bevel pointer
23. Bevel scale
14
15
Catalog
No.
6310-20
FUNCTIONAL DESCRIPTION
21
22
23
16
Volts
DC
18
No Load
RPM
3200
20
1
17
Blade
Size
6-1/2"
2
Arbor
5/8"
Depth of Cut
At 90°
0 to 2-1/8"
3
Depth of Cut
at 45°
0 to 1-9/16"
18
19
4
5
13
12
6
7
8
9
10
11
page 5
CHARGING AND USING BATTERY PACK
Charge your battery pack before using your tool for the first time and
when your tool no longer performs with the power and torque needed
for the job. Full loading capacity of battery pack is only reached after
4 - 5 chargings. Never completely discharge the battery pack. Standard
charging time will vary according to the type of charger you use. The
charging time will also vary depending on the supply voltage and charge
needed. For example, if your battery pack does not require a full charge,
charging time will be less.
FOR SPECIFIC CHARGING INSTRUCTIONS, PLEASE READ THE CHARGER
OPERAT OR'S MANUAL SUPPLIED WITH YOUR CHARGER.
Battery packs are affected by temperature. Your battery pack will
perform best and have longest life if it is charged when the temperature
is between 60°-80°F (15°-27°C). Do not charge in temperatures below
40°F (5°C) or above 113°F (45°C). Under these conditions, capacity will
be reduced. See “Maintenance”.
TOOL ASSEMBLY
WARNING!
To reduce the risk of injury, always
remove battery pack before attaching or
removing accessories. Use only specifically
recommended accessories. Others may be
hazardous.
Removing Battery Pack from Tool (Fig. 1)
Push in the release buttons and slide the battery pack away from
the tool.
Inserting Battery Pack into Tool (Fig. 1)
To insert the battery pack into the tool, push in the release buttons and
slide it into the body of the tool.
Fig. 1
Removing a battery pack
Inserting a battery pack
4. To install a blade, place the blade on the spindle with the teeth
pointing in the same direction as the arrow on the lower guard
(Fig. 3). Release the lower guard lever.
Fig. 3
Selecting Blade
Always use sharp blades. Dull blades tend to overload the tool and
increase the chance of KICKBACK (see page 8). Only use thin kerf
blades with a maximum safe operating speed greater than the no load
RPM marked on the tool's nameplate. Read the blade manufacturer's
instructions before use. Do not use any type of abrasive cut-off wheel
or dry diamond cutting blades.
Installing and Removing Blades (Fig. 2 & 3)
1. Remove battery pack before installing or removing blades.
2. Place the saw on a flat surface with the blade facing upwards. To
remove the bolt from the spindle, push in the spindle lock button.
While holding the spindle lock button in, use the wrench provided
with the tool to turn the bolt clockwise (Fig. 2). Remove the bolt and
blade flange.
Fig. 2
5. Place the blade flange on the spindle and hand tighten the bolt.
6. While holding the spindle lock button in, use the wrench to turn the
bolt counterclockwise and tighten.
Adjusting Depth (Fig. 4 & 5)
1. Remove battery pack.
2. To adjust the depth of the cut, hold the saw by the handle and
loosen the depth adjusting lever by pushing it down toward the shoe
(Fig. 4).
Fig. 4
3. Slide the lower guard lever up to raise the lower guard. Remove the
blade from the spindle. Always clean the spindle, upper guard and
lower guard to remove any dirt and sawdust.
page 6
3. Raise or lower the shoe to the desired position. Markings in 1/4"
increments are located on the inner side of the upper guard for
depth setting. For the proper depth setting, the blade should extend
no more than 1/4" below the material being cut (Fig. 5).
Fig. 5
1/4"
4. Lift the depth adjusting lever up towards the motor housing to
secure the shoe position.
Adjusting the Blade to Shoe (Fig. 8 & 9)
The shoe has been adjusted at the factory to a 90 degree setting.
Inspect the saw regularly to make sure the blade is 90 degrees to the
shoe.
1. Remove battery pack.
2. Set the bevel pointer to zero (Fig. 8).
Fig. 8
Adjusting Bevel Angle (Fig. 6 & 7)
1. Remove battery pack.
2. To adjust the angle of the cut, hold the saw by the handle
and loosen the bevel adjusting knob. (Fig. 6).
Fig. 6
3. Hold the front of the shoe and rotate the saw by the handle to the
desired angle as indicated by the markings on the bevel scale
(Fig. 7).
Fig. 7
3. To make sure the blade is 90 degrees to the shoe, place saw on the
blade side and retract lower guard. Place a square against the blade
and shoe to inspect the degree setting (Fig. 9).
Fig. 9
Bevel adjustment screw
4. To adjust the degree setting, loosen the bevel adjusting knob. Turn
the bevel adjustment screw in or out until the blade is at a 90 degree
angle with the shoe.
5. Tighten the bevel adjusting knob securely.
4. Tighten the bevel adjusting knob securely.
page 7
OPERATION
WARNING!
To reduce the risk of injury, use only specifically recommended accessories. Others
may be hazardous.
Causes and Operator Prevention of KICKBACK:
KICKBACK is a sudden reaction to a pinched, bound or misaligned saw
blade, causing an uncontrolled saw to lift up and out of the workpiece
toward the operator.
When the blade is pinched or bound tightly by the kerf, or cutting slot,
closing down, the blade stalls and the motor reaction drives the unit
rapidly back toward the operator.
If the blade becomes twisted or misaligned in the cut, the teeth at the
back edge of the blade can dig into the top surface of the wood causing
the blade to climb out of the kerf and jump back toward operator.
KICKBACK is the result of tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions
as given below:
1. Maintain a firm grip with both hands on the saw and posi-
tion your body and arm to allow you to resist KICKBACK
forces. KICKBACK forces can be controlled by the operator, if
proper precautions are taken.
2. When blade is binding, or when interrupting a cut for any
reason, release the trigger and hold the saw motionless in
the material until the blade comes to a complete stop. Never
attempt to remove the saw from the work or pull the saw
backward while the blade is in motion or KICKBACK may
occur. Investigate and take corrective actions to eliminate the cause
of blade binding.
3. When restarting a saw in the workpiece, center the saw
blade in the kerf, or cut, and check that saw teeth are not
engaged into the material. If saw blade is binding, it may walk up
or KICKBACK from the workpiece as the saw is restarted.
4. Support large panels to minimize the risk of blade pinching
and KICKBACK. Large panels tend to sag under their own weight.
Supports must be placed under the panel on both sides, near the line
of cut and near the edge of the panel.
5. Do not use dull or damaged blades. Unsharpened or improperly
set blades produce narrow kerf causing excessive friction, blade
binding and KICKBACK.
6. Blade depth and bevel adjusting locking levers must be
tight and secure before making cut. If blade adjustment shifts
while cutting, it may cause binding and KICKBACK.
7. Use extra caution when making a “Pocket Cut” into existing
walls or other blind areas. The protruding blade may cut objects
that can cause KICKBACK.
8. Set the depth of cut for no more than 1/8" to 1/4" greater
than the thickness of the stock. The less blade exposed, the
less chance of binding and KICKBACK. Before cutting, be sure depth
and bevel adjustments are tight.
9. Be cautious of pitchy, knotty, wet or warped stock. These are
most likely to create pinching conditions and possible KICKBACK. Do
not rip warped lumber. Avoid cutting nails.
10. Use a rip fence or edge guide when ripping. Guides improve
control and reduce blade binding.
11. Stay alert. Any distraction can cause twisting or binding. Repetitive
cuts may lull the user into careless movements.
WARNING!
To reduce the risk of injury, wear safety
goggles or glasses with side shields.
General Operation (Fig. 10 & 11)
Always clamp the workpiece securely on a saw horse or bench
(Fig. 10). See “APPLICATIONS” for the correct way to support your work
in different situations.
Fig. 10
1. Draw a cutting line. Place the front of the shoe on the edge of the
workpiece without making blade contact. Hold the handle with one
hand and the front handle with the other (Fig. 11).
Fig. 11
2. Line up the sight line with your cutting line. Position your arms and
body to resist KICKBACK.
3. To start the saw, push the lock-off button down while pulling the
trigger. Allow the motor to reach full speed before beginning cut.
4. While cutting, keep the shoe flat against the workpiece and maintain
a firm grip. Do not force the saw through the workpiece. Forcing a
saw can cause KICKBACK.
5. If making a partial cut, restarting in mid-cut or correcting direction,
allow the blade to come to a complete stop. To resume cutting,
center the blade in the kerf, back the saw away from cutting edge a
few inches, push the lock-off button down while pulling the trigger
and re-enter the cut slowly.
6. If the saw binds and stalls, maintain a firm grip and release the
trigger immediately. Hold the saw motionless in the workpiece until
the blade comes to a complete stop.
7. After finishing a cut, be sure the lower guard closes and the blade
comes to a complete stop before setting the saw down.
Electric Brake
This tool features an electric brake. The brake engages when the trigger
is released, causing the blade to stop and allowing you to proceed with
your work. Generally, the saw blade stops within two seconds. If the
brake misses frequently, the saw needs servicing by an authorized
MILWAUKEE
and you must always wait for the blade to stop completely before removing the saw from the workpiece.
service facility. The brake is not a substitute for the guard,
page 8
Troubleshooting
If the blade does not follow a straight line:
• Teeth are dull. This is caused by hitting a hard object such as a nail
or stone, dulling teeth on one side. The blade tends to cut to the side
with the sharpest teeth.
• Shoe is out of line or bent
• Blade is bent
• Rip fence or guide is not being used
APPLICATIONS
If the blade binds, smokes or turns blue from friction:
• Blade is dull
• Blade is on backwards
• Blade is bent
• Blade is dirty
• Workpiece is not properly supported
• Incorrect blade is being used
Cutting Large Panels (Fig. 12)
Large panels and long boards sag or bend if they are not correctly
supported. If you attempt to cut without leveling and properly supporting
the workpiece, the blade will tend to bind, causing KICKBACK.
Support large panels. Be sure to set the depth of the cut so that you only
cut through the workpiece, not through the supports.
Fig. 12
Ripping Wood
Ripping is cutting lengthwise with the grain. Select the proper blade for
your job. Use a rip fence for rips 4" wide or less. To install the rip fence,
slide the bar through the rip fence slot in either side of the shoe. The
width of the cut is the distance from the inside of the blade to the inside
edge of the rip fence. Adjust the rip fence for the desired width, and lock
the setting by tightening the rip fence adjusting knob.
When ripping widths greater than 4", clamp or tack 1" lumber to workpiece
and use the inside edge of the shoe as a guide.
WARNING!
To reduce the risk of electric shock, check work
area for hidden pipes and wires before making
pocket cuts.
Pocket Cutting (Fig. 14)
Pocket cuts are made in the middle of the workpiece when it can not be
cut from an edge. We recommend using a Sawzall
jig saw for this type of cut. However, if you must use a circular saw to
make a pocket cut, USE EXTREME CAUTION. To maintain control of the
saw during pocket cutting, keep both hands on the saw (Fig. 14).
Fig. 14
®
reciprocating saw or
Cross-Cutting Wood (Fig. 13)
Cross-cutting is cutting across the grain. Select the proper blade for
your job. Advance the saw slowly to avoid splintering the wood.
Fig. 13
1. Beginning at a corner, line up the sight line with your cutting line. Tilt
the saw forward, firmly fixing the front of the shoe on the workpiece.
The blade should be just above cutting line, but not touching it. Raise
the lower guard using the lower guard lever.
2. To start the saw, push the lock-off button down while pulling the
trigger. Allow the motor to reach full speed before beginning cut.
Using the front of the shoe as a hinge point, gradually lower the
back end of the saw into the workpiece. Release the lower guard
lever and grasp the front handle.
3. When the shoe rests flat against workpiece, advance the saw to
the far corner. Release the trigger and allow the blade to come to a
complete stop before removing it from workpiece. Repeat the above
steps for each side of the opening. Use a Sawzall
®
reciprocating
saw, jig saw or small hand saw to finish the corners if they are not
completely cut through.
page 9
MAINTENANCE
WARNING!
To reduce the risk of personal injury always
unplug the charger and remove the battery pack
from the charger or tool before performing any
maintenance. Never disassemble the tool,
battery pack or charger. Contact a
service facility for ALL repairs.
Keep your tool, battery pack and charger in good repair by adopting a
regular maintenance program. After six months to one year, depending
on use, return the tool, battery pack and charger to a
service facility for:
• Lubrication
• Brush inspection and replacement
• Mechanical inspection and cleaning (gears, spindles,
bearings, housing, etc.)
• Electrical inspection (battery pack, charger, motor)
• Testing to assure proper mechanical and electrical
operation
Maintaining Tool
If the tool does not start or operate at full power with a fully charged
battery pack, clean the contacts on the battery pack. If the tool still does
not work properly, return the tool, charger and battery pack to a
MILWAUKEE
Maintaining Battery Pack
MILWAUKEE
dreds of cycles when they are maintained and used according to these
instructions.
A battery pack that is stored for six months without being used will
discharge itself. Batteries discharge at a rate of about 1% per day.
Charge the battery every six months even if it is unused to maximize
battery life. Do not tape the trigger in the “ON” position and leave the tool
unattended as this may discharge the battery to a point where it will no
longer be able to recharge. Use a
no longer performs with the power and torque needed for your application.
Store your battery pack in a cool, dry place. Do not store it where the
temperature may exceed 120°F (50°C) such as in a vehicle or metal
building during the summer. High temperatures will overheat the battery
pack, reducing battery life. If it is stored for several months, the battery
pack will gradually lose its charge. One to three cycles of charging and
discharging through normal use will restore the capacity of the battery
pack. During the life of the battery pack, the operating time between
charges becomes shorter. If the operating time becomes extremely short
after a proper charge, the usable life of the battery pack has been
reached and it should be replaced.
service facility for repairs.
battery packs will operate for many years and/or hun-
MILWAUKEE
MILWAUKEE
MILWAUKEE
Battery Pack only until it
WARNING!
To reduce the risk of personal injury and
damage, never immerse your tool, battery
pack or charger in liquid or allow a liquid to
flow inside them.
Cleaning
Clean dust and debris from charger and tool vents. Keep tool handles
clean, dry and free of oil or grease. Use only mild soap and a damp cloth
to clean the tool, battery pack and charger since certain cleaning agents
and solvents are harmful to plastics and other insulated parts. Some of
these include gasoline, turpentine, lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia and household detergents containing
ammonia. Never use flammable or combustible solvents around tools.
WARNING!
To reduce the risk of explosion, never burn
a battery pack even if it is damaged, dead or
completely discharged.
Disposing of Battery Packs
Battery packs are recyclable. Under various state and local laws, it may
be illegal to dispose of this battery into the municipal waste stream.
Dispose of your battery pack according to federal, state and local regulations.
Repairs
For repairs, return the tool, battery pack and charger to the nearest
service center listed on the back cover of this operator's manual.
Battery Pack Warranty
Battery packs for cordless tools are warranted for one year from the
date of purchase.
WARRANTY
Every
MILWAUKEE
ing our manufacturing facilities. Should any trouble develop, return the
complete tool prepaid to our Corporate Office, Branch Office/Service
Center or nearest Authorized
shows the trouble is caused by defective workmanship or material, all
repairs will be made without charge, and the tool will be returned, transportation prepaid. Battery packs for cordless tools are warranted for
one year from the date of purchase.
This warranty does not apply where: (1) repairs or attempted repairs
have been made by persons other than
thorized Service Station personnel; (2) repairs are required because of
normal wear; (3) the tool has been abused or involved in an accident; (4)
misuse is evident, such as caused by overloading the tool beyond its
rated capacity; (5) the tool has been used after partial failure or (6) the
tool has been used with an improper accessory. No other warranty,
written or verbal, is authorized.
tool is thoroughly inspected and tested before leav-
MILWAUKEE
Service Station. If inspection
MILWAUKEE
personnel or Au-
page 10
Loading...