MiLAN MIL-185C, MIL-195C Installation Manual

Regulatory Approvals

FCC Class A
UL 1950
CSA 22.2 No. 950
EN60950
CE
– EN55022 Class B
– EN50082-1

Canadian EMI Notice

This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.

European Notice

Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the
Low Voltage Directive (73/23/EEC) issued by the commission of the European Community.
Compliance with these directives implies conformity to the following European Norms:
EN55022 (CISPR 22) - Radio Frequency Interference
EN50082-1 (IEC801-2, IEC801-3, IEC801-4) - Elec tromagnetic Immunity
EN60950 (IEC950) - Product Safety

Trademarks:

The MiLAN logo and MiLAN Technology are registered trademarks of MiLAN Technology

in the United States and/or other countries.

To Contact Technical Support:

For prompt response when calling for service, have the following information ready:

- product serial number

- date of purchase

- vendor or place of purchase
You can reach MiLAN Technology technical support at:

- Email: [e-mail]

- Telephone: [phone]

- Fax: [phone]

MiAN Technology
1329 Moffett Park Drive
Sunnyvale, CA 94089
United States of America

Telephone: [phone]
Fax: [phone]

http://www.milan.com

[e-mail]

Five-Year Limited Warranty

MiLAN Technology warrants to the original consumer or purchaser that each of its products,
and all components thereof, will be free from defects in material and/or workmanship for a
period of five years from the original factory shipment date. Any warranty hereunder is
extended to the original consumer or purchaser and is not assignable.

MiLAN Technology makes no express or implied warranties including, but not limited to, any
implied warranty of merchantability or fitness for a particular purpose, except as expressly set
forth in this warranty. In no event shall MiLAN Technology be liable for incidental or
consequential damages, costs, or expenses arising out of or in connection with the
performance of the product delivered hereunder. MiLAN Technology will in no case cover
damages arising out of the product being used in a negligent fashion or manner.

MIL-185C/MIL-195C

AT M



TWIST

ATM Fiber/UTP Converter

© Copyright 2002 MiLAN Technology Printed i n the USA P/N: 90000011 Rev. G

Ethernet

10BASE-FL

MDI

-X/MDI

500mA

Installation Guide MIL-185C/MIL-195C

UTP AC

TIVE

5VDC

FCC PART 15 CLASS A COMPLIANT

RXTX

ATM Twist

Model: MIL 185 

UTP

to

Fiber

ATM
Multi-Mode
CONVERTER

P

O

WE

R

F

I
B

E

R AC

TIVE

UTP AC

TIVE

UTP AC

TIVE

5VDC

FCC PART 15 CLASS A COMPLIANT

RXTX

ATM Twist

Model: MIL 195 

UTP

to

Fiber

ATM
Single-Mode
CONVERTER

P

O

WE

R

F

I
B

E

R AC

TIVE

UTP ACTIVE

MIL-185C

MIL-195C

Installation Guide

This guide includes the following information:

"Introduction" on page 2

"Installation" on page 3

"Configuration Option" on page 4

"Specifications" on page 7

2

Installation Guide MIL-185C/MIL-195C

7

About this Manual

This manual covers both the MIL-185C and the MIL-195C
media converters.

The terms “converter” or “device” are used throughout
the document to describe either the MIL-185C or the
MIL-195C.

Introduction

The MIL-185C and the MIL-195C are compact, physical
media converters that allow the user to convert signals
between ATM fiber optic cabling in either multi-mode or
single-mode, and UTP cabling. Both converters support
OC-3 (155Mbps) speeds.

Features

• Fiber budget sufficient to drive 2 km for multi-mode
or 15 km for single-mode fiber

• One SC-type single-mode (MIL-195C) or one SC-type
multi-mode (MIL-185C) connector

• One shielded RJ-45 UTP connector

• External power supply

• Diagnostic LEDs

• Small form factor

Operating Conditions

Table 1: Recommended Operation Conditions

Parameters Minimum Maximum

Operating Temperature +5° C 40° C
Humidity: non-condensing 10% 95%
Signal Output Load 35 ohm 75 ohm
Supply Voltage 4.75 V 5.25 V

Power Supply

External power is required. The device draws 900 mA at
normal operation in room temperature of 25° C.

• Domestic: 110 V AC wall mount power supply.

• International: 220 V AC power supply with IEC
receptacle.

Connectors

1 2 3 4 5 6 7 8

Figure 5. RJ-45 Connector

RJ-45 Pinouts

• Pin 1 = Transmit Data +

• Pin 2 = Transmit Data -

• Pin 7 = Receive Data +

• Pin 8 = Receive Data -