MiLAN MIL-140CRM, MIL-140TRM Installation Manual
Installation Guide: MIL-140TRM
® Copyright 1998 MiLAN Technology Printed in the USA P/N: 90000111 Rev. B
Regulatory Approvals
• FCC Class A
• UL 1950
• CSA C22.2 No. 950
• EN60950
• CE
–
EN55022
Class B
– EN50082-1
Canadian EMI Notice
This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur
du Canada.
European Notice
Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage
Directive (73/23/EEC) issued by the commission of the European Community. Compliance with these
directives implies conformity to the following European Norms:
• EN55022 (CISPR 22) - Radio Frequency Interference
• EN50082-1 (IEC801-2, IEC801-3, IEC801-4) - Electromagnetic Immunity
• EN60950 (IEC950) - Product Safety
Trademarks
MiLAN Technology™ is a trademark of MiLAN Technology. All other products and brands are the
trademarks of their respective holders. All rights reserved.
To Contact MiLAN
For prompt response when calling for service information, have the following information ready:
• Product serial number and rev.
• Date of purchase
• Vendor or place of purchase
You can reach MiLAN technical support at 408/744-2751
Or E-mail at:
support@milan.com
Address: 1299 Orleans Drive
Sunnyvale, CA 94089
Voice: 408/744-2775
Fax:
408/744-2793
Web: www.milan.com
MIL-140CRM and MIL-140TRM
10BASE-FL to 10BASE-T
Media Converter for MiLAN's
Media Conversion System
Installation Guide
This guide includes the following:
• “Introduction” on page 2
• “Installation” on page 3
• “MDI-X/MDI” on page 3
• “Link Sentry Configuration” on page 5
• “Indicators” on page 6
Five-Year Limited Warranty
MiLAN Technology warrants to the original consumer or purchaser that each of its products,
and all components thereof, will be free from defects in material and/or workmanship for a
period of five years from the original factory shipment date. Any warranty hereunder is
extended to the original consumer or purchaser and is not assignable.
MiLAN Technology makes no express or implied warranties including, but not limited to, any
implied warranty of merchantability or fitness for a particular purpose, except as expressly set
forth in this warranty. In no event shall MiLAN Technology be liable for incidental or
consequential damages, costs, or expenses arising out of or in connection with the performance
of the product delivered hereunder. MiLAN Technology will in no case cover damages arising
out of the product being used in a negligent fashion or manner.
TP
ACT
MIL-
140TRM
FX
LINK
TP
LINK
FX
ACT
MDI-X MDI
10BASE-T
10BASE-FL
Thumbscrews
TX RX
Installation Guide: MIL-140TRM
2 7
About this Manual
This document covers both the MIL-140CRM and the
MIL-140TRM media converter modules. The terms
“MIL-140” and “converter” are used throughout this
document to describe these devices.
Introduction
The MIL-140 converters are part of a series of modules
designed to be installed into MiLAN's Media
Conversion System. These half-/full-duplex devices
convert Ethernet optical signals to electrical and viceversa.
The converter has a signal capability of transmitting up
to 2 km (subject to fiber budget and collision domain
restrictions). This module also has the Link Sentry
feature.
Features
• One RJ-45 (UTP) connector
• One multi-mode, SC or ST fiber connector
• Link Sentry feature
• Diagnostic LEDs
• Management ready–supplied by MiLAN’s optional
SNMP modules (MIL-4650 and MIL-4655)
• Power supply equipped on the rack mount chassis
Figure 2. RJ-45 Pinouts
Fiber Specifications: SC and ST Connector
• 850 nm multi-mode fiber
• 62.5/125 multi-mode fiber
• Launch power: -19 dBm
• Receive sensitivity: -34 dBm
Operating Conditions
Table 2: Recommended Operation Conditions
Parameters Minimum Maximum
Operating Temperature +5° C +50° C
Humidity: Non-condensing 10% 95%
Signal Output Load 35 o hm 75 o hm
Supply Voltage 4.75 V 5.25 V
1
2
3
4
5
6
8
7
Loading...