Miele t8007 User Manual

Operating instructions
for heat pump tumble dryer T 8007 WP SUPERTRONIC
To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time.
en-GB
Caring for the environment
Disposal of the packing material
The transport and protective packing has been selected from materials which are environmentally friendly for disposal and should be recycled.
Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of babies and young children. Danger of suffocation.
Disposing of your old appliance
Electrical and electronic appliances often contain materials which, if handled or disposed of incorrectly, could be potentially hazardous to human health and to the environment. They are, however, essential for the correct functioning of your appliance. Please do not therefore dispose of it with your household waste.
Energy saving tips
To avoid unnecessarily long drying times and high consumption of energy:
Make sure that your laundry is
thoroughly spun before drying. The higher the spin, the greater the savings that can be made in energy and time during drying.
Load according to the optimum
amount of laundry recommended for the programme being used. Underloading is uneconomical. Overloading gives a poorer quality of drying, and may cause unnecessary creasing.
– Make sure that the room temperature
is not too high. If there are other heat producing appliances in the room in which the dryer is located, make sure the room is well ventilated and switch the other appliances off, if possible.
– After every cycle remove fluff from
the surfaces of the fluff filters.
Please dispose of it at your local community waste collection / recycling centre or contact your dealer for advice.
Ensure that it presents no danger to children while being stored for disposal.
2
Contents
Caring for the environment..........................................2
Warning and Safety instructions .....................................6
Operating the tumble dryer.........................................14
Control panel .....................................................14
Selector sensors ..................................................15
Structure of the main menu ..........................................17
Miele{home .....................................................19
Before using for the first time.......................................21
Notes on laundry care .............................................23
Garment care label symbols .........................................23
Tips on drying ....................................................23
1. Sort the laundry and loading the drum .............................24
2. Select a programme.............................................25
Switch the dryer on with the K button ...............................25
– Programmes with drying levels (sensor drying) ......................25
– Programmes which operate by time ...............................26
– Other programmes.............................................26
Select an extra option ............................................27
Start at / Finish at ...............................................27
3. Start the programme ............................................28
Starting a programme............................................28
Time left ......................................................28
Selecting a different programme ...................................28
Start at / Finish at: Changing the time of day ..........................28
Cancelling a programme .........................................29
Adding or removing laundry after a programme has started ..............29
4. End of the programme - unload the drum ...........................30
3
Contents
Extra options ....................................................31
Freshen up.......................................................31
Gentle tumble ....................................................31
Favourite programmes ............................................32
Programme chart .................................................34
Cleaning and care ................................................39
Emptying the condensed water container...............................39
Make sure you clean all the filters at the correct intervals...................40
When to clean the surfaces of the fluff filters ..........................40
When to clean the fine filter .......................................40
Cleaning the surfaces of the fluff filters .................................41
Cleaning them whilst dry .........................................41
Cleaning with water .............................................42
Replacing the filters .............................................42
Fine filter ........................................................43
Removing the fine filter ...........................................43
Cleaning the fine filter ............................................43
Cleaning the cover for the fine filter .................................44
Cleaning the heat exchanger ......................................44
Replacing .....................................................45
Cleaning the tumble dryer ...........................................45
Problem solving guide ............................................46
Check and fault messages in the display ...............................46
An unsatisfactory drying result .......................................49
Other problems ...................................................50
Cleaning the cooling fins (bottom right grille) ............................52
Changing the lamp ................................................53
After Sales service................................................54
Repairs..........................................................54
Future updates (PC) ...............................................54
Appliance guarantee ...............................................54
Optional accessories ...............................................54
4
Contents
Installation and connection ........................................55
Front view........................................................55
Rear view ........................................................56
Transporting the dryer ..............................................56
Installation site ....................................................57
Building under a continuous worktop/ in a row of kitchen units .............57
Levelling the appliance...........................................58
Washer-dryer stack..............................................58
External condensed water outlet ......................................59
Arranging the drain hose .........................................59
External drainage via a sink or gully ................................60
Installation conditions requiring a non-return valve .....................60
Electrical connection .............................................62
Electrical connection U.K. ...........................................62
Consumption data ................................................63
Technical data ...................................................64
Settings menu ...................................................65
Open the Settings menu ............................................65
Language J ......................................................65
Time ............................................................66
Drying levels .....................................................66
Code ...........................................................67
Buzzer ..........................................................69
Keypad tone .....................................................69
Brightness .......................................................69
Contrast .........................................................69
Display / keypad illumination .........................................69
Memory .........................................................70
Anti-crease.......................................................70
Optional accessories..............................................71
5
Warning and Safety instructions
It is essential to read these instructions.
~
This tumble dryer conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property.
To avoid the risk of accidents and damage to the tumble dryer, please read these instructions carefully before using it for the first time. They contain important information on its safety, installation, use and maintenance.
Keep these instructions in a safe place and ensure that new users are familiar with the content. Pass them on to any future owner.
Correct application
This tumble dryer is not designed for commercial use. It is
~
intended for use in domestic households and similar working and residential environments.
The tumble dryer is not intended for outdoor use.
~
It must only be used as a domestic appliance to dry items which
~
have been washed in a water solution and which are marked on the manufacturer's care label as being suitable for tumble drying. If using dry cleaning kits, do so at your own risk, and follow the instructions provided on the packaging. Any other usage is not supported by the manufacturer and could be dangerous. Miele cannot be held liable for damage resulting from incorrect or improper use or operation.
6
Warning and Safety instructions
The tumble dryer can only be used by people with reduced
~
physical, sensory or mental capabilities, or lack of experience or knowledge, if they are are supervised whilst using it or have been shown how to use it in a safe way and understand the hazards involved.
Safety with children
Children under 8 years of age must be kept away from the tumble
~
dryer unless they are constantly supervised.
Children 8 years and older may only use, clean or maintain the
~
tumble dryer without supervision if they have been shown how to do so in a safe way and understand the hazards involved.
The tumble dryer is not a toy! To prevent the risk of injury, do not
~
allow children to play with it or near it, or to play with the controls.
7
Warning and Safety instructions
Technical safety
Before setting up the tumble dryer, check it for any externally
~
visible damage. Do not install or use a damaged tumble dryer.
Before connecting the tumble dryer, ensure that the connection
~
data on the data plate (voltage and frequency) match the mains electricity supply. If in any doubt, consult a qualified electrician.
The electrical safety of this tumble dryer can only be guaranteed
~
when correctly earthed. It is most important that this basic safety requirement is observed and regularly tested, and where there is any doubt, the household wiring system should be inspected by a qualified electrician. Miele cannot be held liable for the consequences of an inadequate earthing system (e.g. electric shock).
Do not connect the tumble dryer to the mains electricity supply by
~
an extension lead. Extension leads do not guarantee the required safety of the tumble dryer (e.g. danger of overheating).
If the electrical connection cable is faulty it must only be replaced
~
by a Miele approved service technician to protect the user from danger.
Unauthorised repairs could result in unforeseen dangers for the
~
user, for which Miele cannot accept liability. Repairs should only be undertaken by a Miele approved service technician, otherwise any subsequent damage will not be covered by the guarantee. Ensure current is not supplied to the tumble dryer until after maintenance or repair work has been carried out.
Faulty components must only be replaced by genuine Miele
~
original spare parts. Only when these parts are fitted can the safety standards of the tumble dryer be guaranteed.
8
Warning and Safety instructions
The tumble dryer must be isolated from the electricity supply in
~
the event of a fault and during cleaning and maintenance.
The tumble dryer must not be used in a non-stationary location
~
(e.g. on a ship).
Do not make any alterations to the tumble dryer, unless
~
authorised to do so by Miele.
Heat pump technology and refrigerant:
~
The heat pump in this tumble dryer uses a refrigerant which is condensed by the compressor and led in a closed circuit through the heat exchanger unit where heat exchange with the circulating drying air takes place.
– The humming noises caused by the heat pump are normal and do
not impair the efficient functioning of the dryer.
– The refrigerant is not flammable or explosive.
– In general it is not necessary to leave the dryer standing for any
length of time before it is put into operation provided it has been transported correctly (see "Installation"). However, if it has not been transported as described, ensure that the recommended standing time prior to first operation is observed. Otherwise the heat pump can be damaged.
In areas which may be subject to infestation by cockroaches or
~
other vermin, pay particular attention to keeping the tumble dryer and its surroundings in a clean condition at all times. Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee.
9
Warning and Safety instructions
Correct use
To prevent the risk of fire, the following textiles must not be dried
~
in this appliance:
items which have not been washed.
items, such as workwear, which have not been thoroughly
cleaned and which are still soiled with grease, oil or other deposits (such as cosmetics, lotions etc). If items have not been thoroughly cleaned there is a danger that these might self-ignite when heated, even after they have been removed from the dryer at the end of the programme.
– items (e.g. mops and floor cloths) which have been treated with
inflammable cleaning agents or which contain residues of acetone, alcohol, benzine, petrol, kerosene, stain remover, turpentine, wax and wax remover or other chemicals.
– items which have been splashed with hair lacquer, hair spray, nail
varnish remover or similar substances.
When washing such heavily soiled items, ensure that you use additional detergent and select a high temperature. If in doubt, wash the items several times.
Remove all items such as lighters and matches from pockets.
~
Warning: Do not switch the tumble dryer off before the drying
~
programme has finished. If this is done, the laundry must be hung up or spread out to cool it down.
10
Warning and Safety instructions
Danger.
~
This tumble dryer must not be connected to a controllable socket (e.g. a timer switch or a peak load shut-off device). If the dryer programme were to be interrupted before the end of the cooling down phase, the laundry could self-combust.
To prevent the risk of fire, the following must not be tumble dried:
~
items which have been cleaned using chemicals (e.g.
professional dry-cleaning agents).
fabrics which contain a large proportion of rubber, foam rubber or
rubber-like materials. For example, products made from latex foam rubber, shower caps, waterproof textiles, rubberised articles and items of clothing and pillows with foam rubber filling.
– damaged items which contain padding or fillings (e.g. pillows,
jackets). When damaged, the filling can get out with the risk of igniting in the dryer.
In many programmes, the heating phase is followed by a cooling
~
down phase to ensure that the items are not too hot to handle when you remove them (this also avoids the danger of the laundry self-igniting). The programme is not finished until the cooling down phase has been completed. As soon as the programme has finished, remove all laundry from the drum.
Fabric conditioner and similar products must be used according
~
to the instructions on the manufacturer's packaging.
Do not let anyone sit or lean on the door, as this can cause the
~
tumble dryer to tip up.
Always close the door after use. This way you will avoid the
~
danger of: –
children climbing into the dryer or hiding things in it.
pets or other small animals climbing into it.
11
Warning and Safety instructions
The tumble dryer must not be used:
~
without the fluff filters in place or if the fluff filters are damaged in
any way.
without the fine filters in place of if the fine filters are damaged in
any way.
This would cause an excessive build-up of fluff which in turn would cause a fault.
After every cycle remove fluff from the surfaces of the fluff filters.
~
The fluff filters and the fine filters must be thoroughly dried after
~
cleaning. Damp or wet filters could cause operational faults.
Do not install the tumble dryer in a room where there is a risk of
~
frost occurring. At temperatures around freezing point the tumble dryer may not be able to operate properly. There is a risk of damage if the condensed water is allowed to freeze in the pump and in the drain hose.
If the water is drained externally instead of being collected in the
~
condensed water container, make sure the drain hose is securely attached if you hang it in a sink or basin to avoid the hose slipping and the water causing damage.
Condensed water is not drinking water. It can cause health
~
problems in both people and animals.
Always keep the area around the tumble dryer free of dust and
~
fluff. Dust drawn into the tumble dryer can cause blockages in the heat exchanger unit over time.
The tumble dryer must not be hosed down.
~
12
Warning and Safety instructions
Accessories
Only use genuine Miele original spare parts and accessories with
~
this tumble dryer. If non-Miele parts are used, guarantee, performance and product liability claims may be invalidated.
Miele cannot be held liable for damage caused by non-compliance with these Warning and Safety instructions.
13
Operating the tumble dryer
Control panel
a Miele{home
Symbol for Miele|home enabled appliance
b Information sensor :
The sensor lights up when information about the menu in the display is available.
c Service interface
This is used by service technicians to run diagnostic checks on your machine, or to update programming data in the future.
d Selector sensors
A sensor is active when it is lit up. See next page for more information.
e Display
For showing:
the functions selected
the programme sequence
information
error messages
the time of day
the position of an entry using the scroll bar
f Clear sensor U
For returning to the previous menu.
For returning to the main menu when
touched twice.
– For deleting the values set
previously.
– For cancelling the programme.
g Start sensor
The programme selected is started by touching this sensor when it is illuminated green.
h K button
For switching the dryer on and off. To save energy the dryer will switch off automatically 15 minutes after the end of the programme/anti-crease phase or 15 minutes after the dryer is switched on if it is not operated.
i / button
For opening the door. The dryer does not need to be switched on at the mains.
14
Selector sensors
Selecting an option
Operating the tumble dryer
The selector sensors are on the left and right of the display. They light up when they are active. The selector sensors are used for the following:
A dot ( The selector sensor on the left is active when the dot ( front of the word, the selector sensor on the right is active when the dot (
Scrolling through the menus
If the menu lists more options than are visible in the display, a scroll bar will appear on the right to show the position in the list:
The sensors on the right can be used to scroll up or down the list. Each touch of the sensor will move the list up or down one line.
A dotted line will appear under the last option in the list.
Changing a value in the display
Use the + and - sensors on the right to alter the value highlighted. Once altered confirm the value with the l sensor at the bottom right hand side.
#) next to an option indicates that it can be selected.
Main menu
\
$ Favourite programmes # Cottons
\
! Minimum iron
\
Time
#) is behind the word or symbol.
10 :21
10:21
m
+ $
#
OK !
OK
#)isin
[
[
[ [ [
15
Operating the tumble dryer
Favourite programmes
You can save up to ten of your own customised programmes under names of your choice.
Drying assistant
This helps you find the correct wash programme. The drying assistant guides you step by step so that you can select the best programme for the fabrics and garments you want to dry.
Settings menu
The Settings menu tumble dryer's electronics to suit different requirements. See "Settings menu" for more details.
Information sensor :
The Information sensor : will light up if information about an option is available. Touch the sensor if you want to read the information.
! is used to alter the
Programme sequence display
Symbols in the display show which section of the programme has been reached.
Symbol Programme sequence
Start at / Finish at
R
Drying
G
Machine iron
I
Hand iron rr
G
Hand iron r
H
Normal
E
Normal+
F
Cooling down / Cancel
7
16
C
Cool air
Warm air
D
Anti-crease/Finish
O
Structure of the main menu
Favourite programmes
Cottons
– Minimum iron
– Delicates
– .... – Drying level: (depending on programme)
– .... – Duration (depending on programme)
Drying tips
Operating the tumble dryer
Favourite programmes
(listed alphabetically)
Create
Change
Delete
– Extras (depending on programme)
– Start at
– Finish at
– Cottons*
Delicates*
Cotton + synthetic*
Woollens
Silks
Microfibre*
Linen*
* This option has further choices.
17
Operating the tumble dryer
Settings !
Language
Time*
Buzzer
Drying levels*
Code
Keypad tone
Brightness
Contrast
– Display / keypad illumination
– Memory
– Anti-crease – Miele|home**
– Remote control**
* This option has further sub-menus.
!
** Appears if the dryer has been fitted with the optional communication module.
18
Miele{home
a Communication-enabled appliances
b Communication module
c SuperVision master appliance
d Power supply
e Miele|home Gateway
f (WLAN) Router
Possible connections (optional)
g PC, Notebook
h iPod* or iPhone*
i Connection with a domestic bus
system display
j Possible internet conection
* iPod and iPhone are registered trade marks of Apple Inc.
19
Miele{home
Depending on country, this appliance is communication enabled and can be linked into the Miele|home system via a communication module b(optional accessory).
Miele|home enabled appliances send information via the household power supply network d to the master appliance c about the operational status of the appliances, as well as information about the progress of the programme.
Displaying information, controlling appliances
– SuperVision master appliance c
The status of other communication enabled appliances in the system can be shown in the display of the SuperVision master appliance.
– Mobile terminal appliances g/h
A PC, Notebook or an iPod* /
iPhone* can be used within the operating radius of a WLAN to display status information about the networked appliances and to carry out some operational commands.
Optional accessories required
Communication module
This must be fitted by a Miele service technician.
Miele|home Gateway
Both of these are supplied with their own installation and operating instructions.
Further information
For further information about Miele|home, SuperVision and future options please contact Miele.
Household network i Miele|home enables smarter living. With the Miele|home Gateway e communication-enabled appliances can be integrated into the domestic bus system.
* iPod und iPhone are registered trade marks of Apple Inc.
20
1. Welcome screen
2. Set the language
Before using for the first time
Before using the dryer for the first time ensure that it is correctly installed and connected. See "Installation".
If the tumble dryer has not been transported as
,
described in "Installation" then it must be left to stand for at least 1 hour before Otherwise the heat pump may become damaged.
Preparing the dryer for use is done in five steps. The dryer guides you automatically through steps 1. to 5.
Switch the dryer on with the K button.
^
The welcome screen will appear in the display for 3 seconds. The display for setting the language will then appear.
it is connected to the electricity supply.
Sprache
\
$ deutsch ( # english
\
! español
\
^
Select the language you want.
^
The sensors on the right can be used to scroll up or down the list.
^
Confirm the language you have selected with
10:21
p
OK !
OK.
[ [ [
21
Before using for the first time
3. Set the time of day (if required)
Enter the time of day.
Time
10 :21
OK !
+ and - to set the hour.
Use
^
Confirm with
^
4. Miele|home message
This communication enabled dryer can transmit programme data through the power lines to the Miele|home system if it has been fitted with a communication module (optional accessory).
^ Confirm the message with
5. Continue setting the dryer up as described in the Operating instruction manual.
The dryer is correctly set up once a programme lasting longer than one hour has been run (See "2. Selecting a programme").
The welcome screen and request to set the language will appear in the screen after switching the dryer on again if a programme lasting less than 1 hour was run.
OK. Then set the minutes and confirm with OK.
OK.
+ $
#
[ [ [
22
^
Confirm the message with
OK.
Notes on laundry care
Garment care label symbols
Drying
q/r Normal/low temperature
Drying is carried out at a low temperature in every programme, so you do not need to sort your garments according to whether they have the q or
r symbol.
s Do not tumble dry
Tips on drying
– Always observe the maximum
recommended loads given in the "Programme chart". Never overload the drum.
Overloading can cause unnecessary wear and tear to the laundry, give a disappointing drying result and cause more creasing.
– Do not put soaking wet items into the
tumble dryer. Spin fabrics for at least 30 seconds before drying.
Use the Automatic plus programme for drying mixed loads of cotton and minimum iron fabrics.
Open jackets evenly.
Pure linen dried if specified as suitable by the manufacturer on the garment care label, as the surface of the fabric may otherwise become rough.
so that they can dry
should only be machine
Loopknit garments
underwear) tend to shrink depending on their quality. Do not over-dry these textiles. When purchasing these garments it is advisable to take their shrinkage properties into account.
Minimum iron fabrics
more, the larger the load. This is also the case for garments made from very fine weave fabrics, such as shirts or blouses. Make sure you select a suitable programme. If in doubt, divide the garments into smaller loads and select the Gentle tumble extra option.
– Starched laundry
tumble dryer. To achieve the usual finish, double the amount of starch should be used.
– New dark coloured garments
be washed and dried separately from light coloured garments to avoid the danger of colours running and discolouring other garments or even plastic components in the dryer. Dark coloured fibres can also settle on light coloured garments and vice versa.
Use the Drying basket programme for drying / airing items which are not suitable for drying with mechanical action. Important: You must use a Miele drying basket (optional accessory).
(e.g. T-shirts and
tend to crease
can be dried in the
should
23
1. Sort the laundry and loading the drum
Prepare the laundry
To ensure an even drying result sort the washed laundry according to:
.. . . . the drying level required, . . . the type of fibre or weave, . . . size, . . . the moisture content after spinning.
Make sure that objects, e.g.
,
detergent dispensing balls, have been removed from the laundry. They could melt and cause damage to the dryer or the laundry.
– Check seams and stitching to ensure
that padding and linings are intact.
– Fasten duvet covers, pillow cases
etc. to prevent small items from being rolled up inside them.
– Fasten zips, hooks and eyes etc.
– Tie fabric belts and apron strings.
Load the tumble dryer
Press the a button to open the
^
door.
Load the laundry loosely into the
^
drum.
Do not overload the drum. See the "Programme chart" for recommended loads for each programme. Overloading can cause unnecessary wear and tear to the laundry, and give a disappointing drying result.
^ Before closing the door make sure
the fluff filter is correctly positioned.
– Sew in or remove underwiring from
bras.
24
Check the laundry is right inside the drum so that it cannot get trapped or damaged when the door is shut.
^
Shut the door either with a gentle swing, or lean against it and push it shut.
Switch the dryer on with the K button
2. Select a programme
Main menu
\
$ Favourite programmes # Cottons
\
! Minimum iron
\
Select the programme you want: Use the right hand
^
sensors to show more programmes.
An additional menu may appear depending on the programme selected:
– Programmes with drying levels (sensor drying)
e.g. Cottons ... : You have a choice of drying levels with this programme.
Cottons 1-8 kg 2:03 h
\
$ Drying level: Normal # Extras
\
# Start at
\
^ Touch the Drying level sensor.
Drying levels
\
$ Normal ( # Hand iron r
\
! Hand iron rr
\
^
If there are more than 3 levels to choose from: Use the right hand sensors to show more levels.
10:21
m
10:21
m
10:21
p
OK !
[
[
[
[
[ [ [
^
Touch the left hand sensor to confirm the drying level required.
^
Confirm with OK.
25
2. Select a programme
– Programmes which operate by time
e.g. Warm air ... : You have to select a duration.
– Other programmes
Warm air 1-7 kg 0:20 h
\
$ Duration # Extras
\
# Start at
\
Touch the Duration sensor.
^
Use the
^
which is highlighted.
Confirm the value you have set with
^
Cool air: 20 mins - 1 hour
Warm air: 20 mins - 2 hours
Basket programme: 40 mins - 2:30 hours
e.g. Gentle smoothing ... : These programmes have fixed drying levels / durations and cannot be altered.
\ \
+ and - sensors on the right to alter the value
Gentle smoothing 1 kg 1:06 h
$ Start at # Finish at
0:25
h:min
OK.
10:21
+ $
#
OK !
10:21
[ [ [
26
Select an extra option
2. Select a programme
Start at / Finish at
Extras
\
$ 9 Freshen up # 8 Gentle tumble
\
Select the Extra you require.
^
When you select
Freshen up the items are aired until they are at the Normal
drying level.
Gentle tumble drum rotation is reduced for less
mechanical action.
A tick
9 will appear to show which Extra has been selected.
^ Confirm with
You can set the start (Start at) or the end (Finish at) time of a programme.
The start and end time can be set in steps of 15 minutes. You can delay the programme start time or the programme end time up to a maximum of 24 hours. With the first 15 minute step the time will be adjusted to the next quarter of an hour.
OK.
10:21
OK !
[
^
Select the Start at or the Finish at option.
OK.
10:21
+ !
[ [ [
Cottons 1-8 kg 2:03 h
\
$ Extras # Start at
\
! Finish at
\
^
Use
+ and - to select the time you want for Start at or Finish
at. Confirm the time you have selected with
Please note: Selecting or deselecting an Extra or altering the drying level subsequently, can postpone the programme end time.
01:27 – !
03:30 OK !
27
3. Start the programme
Starting a programme
Touch the green illuminated Start sensor.
^
G
The time left counts down in the display.
Symbols in the display show which section of the
programme has been reached.
Time left
The following factors all affect the estimated time left: the residual moisture after spinning; the type of textile; the load; the ambient room temperature; fluctuations in the power supply or a programme interruption. The time left is continually monitored and altered during drying. This is why the time shown in the display may fluctuate during the programme. This is quite normal. Programmes can also finish earlier than expected, if, for example, particularly fine fabric is being dried, the load is very small or items were partially dry beforehand.
Cottons 10:21
Normal - Extras (See :)
Time left: 2:03 h
Change !
[
Some changes can be made after starting a programme: Selecting a different programme
You cannot change to another programme once a programme has started (this prevents unintentional alterations). You will need to cancel the current programme before you can select a new one.
Start at / Finish at: Changing the time of day
^
Touch the Change sensor.
^
Select the Start at or the Finish at option.
^
Use
+ or - to alter the time of day.
^
Confirm the time you have selected with the
28
OK sensor.
Cancelling a programme
Touch the U sensor.
^
3. Start the programme
Cottons
: Cancel programme?
! Continue
\
Select Cancel.
^
The items will be cooled down temperature reached and how long they have been dried for.
If you select U and Cancel again, the display.
^ Press the s button to switch the dryer off.
^ Press the s button to switch the dryer on.
^ Select another programme and start it.
An alternative way to cancel
^ Press the a button.
Adding or removing laundry after a programme has started
^
Press the a button.
^
Open the door.
7, depending on the
O Finish will appear in
10:21
Cancel !
[
^
Add or remove items as required.
^
Close the door.
^
Select a programme.
^
Touch the Start sensor.
29
4. End of the programme - unload the drum
Before the end of a programme
There is a cooling down phase at the end of the drying sequence:
7 (=
Cooling down) appears in the display. The programme is not finished until the cooling down phase has been completed.
End of the programme - unload the drum
O Anti-crease and Finish will appear in
the display to indicate that the programme has finished. The buzzer will sound at intervals.
The dryer has an energy saving mode: After the programme has finished, the display will go out and the Start sensor will flash slowly (see also "Settings menu - Display / Keypad illumination". During the Anti-crease phase, the drum will rotate at intervals to prevent laundry creasing. This is quite normal.
^ Press the a button to open the
door.
Press the s button to switch the
^
dryer off.
The buzzer will sound.
Close the door.
^
Empty the condensed water
^
container unless the dryer has been connected for external drainage, in which case it does not have to be emptied.
Drum lighting
To give a good view of the inside of the drum so that no items are overlooked:
The lighting comes on when the door is opened if the dryer is switched on. It will go out after a short while if the door is left open and after the door is closed to save energy.
^
Remove the laundry.
Check that all items have been removed from the drum. If items are left in the dryer, they could be damaged by overdrying when the dryer is next used.
The dryer will switch off automatically 15 minutes after the end of a programme / the end of the anti-crease phase.
(If the dryer is signed on to the Miele|home system, it will not switch off automatically).
30
Extra options
Freshen up
The drying air is heated up for a specific length of time. After this, the garments are aired to the Normal drying level without any more heat being added. Use the Freshen up extra option to eliminate or reduce unwanted smells in clean (dry or damp) clothing. Items must be suitable for drying in a tumble dryer. Dampen the garments a little beforehand or add a fabric conditioner sheet. Odours will not be removed as effectively from any parts of the garments which are made of synthetic fibres.
Gentle tumble
For drying items which can be dried in a tumble dryer but which are particularly susceptible to creasing or which are not suitable for drying with a great deal of mechanical action. When this option is selected, the drum will rotate less frequently. The programme duration is longer.
Optional extras
This dryer offers the following extras:
Freshen up
Cottons ## Minimum iron ## Shirts ## Denim ## Sportswear # Warm air #
However, you have to choose either the Freshen up or Gentle tumble option.
Gentle tumble
Note
You can alter the drying levels for some programmes (see "Settings menu").
This dryer also has a buzzer and an anti-crease phase at the end of the programme which can be altered (see "Settings").
31
Favourite programmes
You can save up to ten programmes with the settings you have selected for them under names of your choice. The name can have up to 12 characters.
The favourite programmes which have been set are stored alphabetically.
To save a favourite programme
There are two ways of saving a programme as a favourite.
1. Open the Favorite programmes menu and select Create. You can then select a programme in the usual way.
2. If you alter a drying level or select an Extra when you select the programme: Also select Save as.
To enter a name for a favourite programme
Name: ? A A A A A A A A A A A
) A BCDEFGHIJKLMNOPQRS
\
! Select character
\
^ Select the first character and confirm this with Select
character.
Use the the characters.
^
After the first letter in upper case has been entered the display will change automatically to display letters in lower case. After a space has been entered the display will revert to upper case again.
* sensor to scroll to the right to select the rest of
10:21
*
[
32
To save a name for a favourite programme
Favourite programmes
Name:Dry_______
\
$ Space ) ghijklmnopqrstuvwx y
\
! Select character
\
Select Confirm name.
^
To select a favourite programme
Call up the Favorite programmes menu. The saved
^
programmes will appear in alphabetical order.
Select the favourite programme you want.
^
^ Touch the green illuminated Start sensor. The programme
will start.
To change a favourite programme
^ Select the Change option.
^ Select the favourite programme you wish to change.
^ Make any changes and then save it under the same name.
The altered parameters will be active the next time the favourite programme is started.
To delete a favourite programme
10:21
Delete character $
*
Confirm name !
[ [ [
If you have already saved ten favourite programmes then you will have to delete one of them before you can save a new programme.
^
Select the Delete option.
^
Select the favourite programme you wish to delete.
^
Confirm the deletion.
33
Programme chart
Cottons Max. load 8 kg*
Extra dry, Normal+, Normal**
Use for Single and multi-layered cotton fabric such as Towelling, T-shirts,
underwear, flannelette bed linen and baby clothes.
Notes
Hand iron r, Hand iron rr, Machine iron
Use for Cotton or linen fabrics e.g. Table linen, bed linen, starched laundry.
Note To prevent laundry from drying out, it should be rolled up until you are
Minimum iron Max. load 3.5 kg*
Normal+, Normal, Hand iron r
Use for Minimum iron cotton, synthetic and mixed fibre fabric. e.g. tops,
Delicates Max. load 2.5 kg*
Normal+, Normal, Hand iron r, Hand iron rr
Use for Synthetic, mixed fibre, rayon and easy care cotton, e.g. shirts, blouses,
* Weight of dry laundry Note for test institutes: –
** Test programme (without selecting any Extra options) in accordance with Regulation 392/2012/EU for energy labelling measured in accordance with EN 61121.
When selecting the Cottons programme, drain the condensed water away through the drainage hose.
Select Extra dry for multi-layered and very thick fabrics.
Do not use Extra dry for loopknit fabrics (e.g. T-shirts, underwear,
baby clothes), as they have a tendency to shrink.
ready for ironing.
dresses, trousers, skirts and table cloths.
lingerie and appliquéd garments.
34
Programme chart
Automatic plus Max. load 5 kg*
Normal+, Normal, Hand iron r
Use for Mixed loads of garments suitable for the Cottons and Minimum iron
programmes. Sort according to colour.
Shirts Max. load 2 kg*
Normal, Hand iron r
Use for Shirts and blouses.
Denim Max. load 3 kg*
Normal, Hand iron r
Use for Denim garments, e.g. jeans, jackets, skirts, shirts.
Express Max. load 3.5 kg*
Extra dry, Normal+, Normal, Hand iron r, Hand iron rr, Machine iron
Use for Fabrics which can tolerate high temperatures and which can be dried
using the Cottons programme.
Note – Short programme duration.
Woollens Max. load 2 kg*
Use for Woollen garments and fabrics containing wool blends.
Notes – This programme only fluffs up woollen garments. They are not dried
completely.
Remove garments as soon as the programme has finished.
Silks Max. load 1 kg*
Use for Silks (those suitable for drying in a tumble dryer), e.g. blouses and
shirts.
Notes
* Weight of dry laundry
Smooths out creasing.
Remove garments as soon as the programme has finished.
35
Programme chart
Sportswear Max. load 3 kg*
Normal+, Normal, Hand iron r
Use for Sportswear which is suitable for drying in a tumble dryer.
Outerwear Max. load 2.5 kg*
Normal, Hand iron r
Use for Outerwear which is suitable for drying in a tumble dryer.
Cottons hygiene Max. load 3.5 kg*
Normal
Use for Cotton and linen fabric which is in direct contact with the skin, e.g.
underwear, baby clothes, bed linen, towelling.
Note The temperature is held constant for a longer period of time (longer
temperature holding time) to deactivate micro-organisms, e.g. bacteria or house dustmites, and also to reduce the number of allergens in the laundry. To ensure that the micro-organisms are deactivated, do not interrupt the programme.
Proofing Max. load 2 kg*
Normal
Use for Drying microfibre fabric, skiwear, fine, closeweave cotton garments
(poplin) or tablecloths which are suitable for drying in a tumble dryer and have been treated to provide a water and dirt resistant finish.
Notes
* Weight of dry laundry
This programme includes a proofing fixing phase.
Only use proofing agents containing fluorochemical compounds which are stated by the manufacturer as being "suitable for use on membrane textiles".
Do not dry items which have been treated with proofing agents containing paraffin. Fire hazard.
36
Programme chart
Pillows 1-2 pillows up to 80 x 40 cm
Large pillows 1 pillow up to 80 x 80 cm
Normal
Use for Pillows suitable for drying in a tumble dryer, with feather, down or
synthetic fillings.
Note Please observe the instructions on the care label. Pillows can still feel
damp after being dried. You can use this programme several times until the pillow feels dry.
Gentle smoothing Max. load 1 kg*
Use for
Notes – Suitable for dry and damp laundry.
* Weight of dry laundry
Cotton and linen fabric
Minimum iron mixed fibre, cotton or synthetic fabric, e.g. trousers,
anoraks, shirts
Dry garments are time-controlled, damp garments are smoothed to the Hand iron stage.
– Smooths out creasing caused during the spin cycle in the washing
machine.
– Remove garments as soon as the programme has finished so that
they are easy to iron.
37
Programme chart
Cool air Max. load 7 kg*
Use for Any item which only needs airing.
Warm air Max. load 7 kg*
Use for
Note
Basket programme Max. load for basket: 3 kg
Notes
Use for See the operating instructions supplied with the drying basket.
* Weight of dry laundry
Drying voluminous and multi-layered fabric whose layers have
different drying characteristics, e.g. jackets, pillows. For drying individual items, e.g. bath towels, swimwear,
tea-towels.
Do not select the longest drying time to start with. Check the
items as you are drying them to find the optimum time.
The drum does not rotate in this
programme. For this reason, airing and drying may only be carried out if the Miele drying basket (optional accessory) is fitted in the drum.
– Use this programme to dry items which
are suitable for drying in a tumble dryer but which are not suitable for drying using mechanical action.
– A satisfactory drying result cannot be achieved without the drying
basket.
– It is essential to observe the operating instructions for the drying
basket.
38
Emptying the condensed water container
The condensed water will be collected in the condensed water container.
Empty the condensed water container after every drying programme.
If the maximum level of the condensed water container is reached
the programme will be cancelled.
Empty the container will appear in
the display.
Cleaning and care
Empty the container.
^
^ Replace the container in the dryer.
To delete the message:
^ Switch the dryer off and then on
again.
^
Pull out the condensed water container.
^
To prevent water running out, hold it at the front and towards the back and keep it in a horizontal position when carrying it.
Condensed water should not be
,
consumed. It could lead to health problems for people and animals.
Condensed water can be put to household use (e.g. in a steam iron or humidifier). To ensure that any residual particles of fluff in the condensed water are removed before use, pass it through a fine sieve or paper filter first.
39
Cleaning and care
Make sure you clean all the filters at the correct intervals
This tumble dryer has a multi-stage filter system, consisting of the fluff
filters and a fine filter.
This dryer must not be used
without the fluff filters or fine filter in place. The grille in the bottom right must always be in place.
Make sure that the fluff filters and
the fine filter are not damaged. Replace them immediately, if they are damaged in any way (optional accessories).
If the above instructions are not
,
observed, an excessive build-up of fluff can occur which in turn can cause a fault.
When to clean the surfaces of the fluff filters
When to clean the fine filter
Only clean the fine filter when Clean the plinth filter which is located in front of the heat-exchanger appears
in the display.
The plinth filter is located on the left of the dryer behind the panel. It collects finer fluff, hair and detergent residues which have got through the surfaces of the fluff filters in the door and the door opening.
^ See "Fine filter".
^ To delete the message: Touch the
OK sensor.
Clean the surfaces of the fluff filters after each drying programme.
The fluff filters located in the door and the door opening collect fluff from items being dried.
^
See "Cleaning the surfaces of the fluff filters".
40
Cleaning the surfaces of the fluff filters
When to clean
Clean the surfaces of the fluff filters in the door and the door opening after each drying programme.
Cleaning them whilst dry
Note: You can also use a vacuum cleaner to remove the fluff.
Cleaning and care
Use your fingers or a vacuum cleaner
^
to remove the fluff from the surface of
1 Fluff filter 2 Door seal
^
Open the door and pull the fluff filter (1) out of the door as illustrated.
^
Remove any fluff from the hollow part of the door with a bottle brush or a vacuum cleaner.
^
Also clean the door seal (2) with a damp cloth.
the filter.
^
Use your fingers or a vacuum cleaner to remove the fluff from the two fluff filters in the door opening.
^
Once clean, push the filter back into the door holder until it clicks into position. Ensure it is facing the correct way.
^
Close the door.
41
Cleaning and care
Cleaning with water
If there is a great deal of compacted fluff on any of the filters, they can be removed and cleaned under hot running water.
Open the door and pull the fluff filter
^
out of the door as described previously.
The two filters in the door opening can also be removed if you need to clean them with water.
Replacing the filters
Do not replace the filters if they
,
are damp or wet. Damp or wet filters could cause operational faults.
Push the large filter back into the
^
door holder until it clicks into position. Ensure it is facing the correct way.
Replace the filters in the door
^
opening by first inserting them at the bottom and then pressing them into place at the top.
Lock both dials (you will hear them
^
click).
^
Turn dial a until you hear it click.
^
Pull the filter by the dial out of the door opening as shown b.Dothe same on the other side.
^
Rinse the filters under hot, running water.
^
Dry the filters thoroughly with care.
^
Also clean the airways underneath them, e.g. with a vacuum cleaner.
42
Fine filter
When to clean
Only clean the fine filter when Clean the plinth filter which is located in front of the heat-exchanger appears
in the display.
To delete the message: Touch the
^
OK sensor.
Removing the fine filter
Switch the dryer off.
^
On the front left of the tumble dryer:
Cleaning and care
Pull the filter out by the handle.
^
^
Press to open the access panel for the fine filter (see arrow).
The panel will spring open.
^ Pull the handle out of the filter.
Cleaning the fine filter
^
Clean the fine filter thoroughly under running water.
^
Then squeeze it thoroughly.
,
It must not be replaced dripping
wet as this can cause a fault.
^
Use a damp cloth to remove any fluff from the handle.
43
Cleaning and care
Cleaning the cover for the fine filter
^ Use a damp cloth to remove any
fluff. Make sure that you do not damage the rubber seal when doing this.
^ Check whether the cooling fins are
blocked with fluff (as follows).
Cleaning the heat exchanger
Danger of injury.
,
Do not touch the cooling fins. You could cut yourself.
Prevent damage.
,
Carefully pass the vacuum cleaner brush over the surface, without applying any pressure. Otherwise the cooling fins or the struts in front of them could become damaged.
Visible soiling:
44
^
Remove any visible soiling carefully with a vacuum cleaner using a dusting brush or a narrow crevice nozzle.
Replacing
Fit the filter back on the handle. Make
^
sure it is the correct way round.
To ensure that the filter is positioned correctly in the front of the heat exchanger unit:
Cleaning and care
The filter must be fitted correctly and the access flap closed to ensure that water cannot leak from the condenser system and to ensure that the dryer functions efficiently.
Cleaning the tumble dryer
Disconnect the dryer from the mains electricity supply.
Clean the housing, control panel and
^
door seal with a slightly damp cloth and a mild detergent or soapy water.
^ The drum and other stainless steel
parts can be cleaned with a suitable proprietary stainless steel cleaner following the manufacturer's instructions.
Do not use solvents, abrasive cleaners, glass cleaners or all-purpose cleaners. These could damage plastic sufaces and other parts.
^
First insert the handle with the filter attached over the two guide pins.
Make sure that the yellow dot on the handle is on the right.
^
Push the filter in completely.
^
Close the access flap.
^
Dry all parts with a soft cloth.
45
Problem solving guide
With the help of the following notes minor faults in the performance of the appliance, some of which may result from incorrect operation, can be put right without contacting the Service Department.
Repair work to electrical appliances should only be carried out by a
,
suitably qualified person in strict accordance with current local and national safety regulations. Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work.
Check and fault messages in the display
Problem Possible cause Remedy
You are asked to enter a code.
Adjust the load
1
The programme is cancelled, the buzzer sounds.
Empty the container
N
Empty the container or check the drain hose.
The programme is cancelled, the buzzer sounds.
Access via a code has been activated.
This is not a fault. The electronic unit has
recognised that there is no laundry or insufficient laundry in the drum and cancelled the programme. Drying individual garments or items which are already dry can also cause the programme to be cancelled.
The condensed water container is full or there is a kink in the drain hose.
Enter the code (see Settings menu).
Use the Warm air programme for drying individual items.
– Open and shut the
door.
Empty out the condensed water container or check the
drain hose. To delete the message: –
Switch the dryer off
and then on again.
46
Problem solving guide
Problem Possible cause Remedy
Clean the plinth
:
filter which is located in front of the heat-exhanger
appears at the end of a programme.
Fit plinth filter
;
Fit the plinth filter
appears and the programme cannot be started.
Technical fault
;
F1
Comfort cooling
This is a reminder to clean the fine filter in front of the heat exchanger unit under running water.
The fine filter is missing or has been replaced the wrong way round.
Removing the fine filter during a drying cycle will cause the programme to be cancelled.
A programme cannot be started while there is a fault message in the display.
The programme has finished but the laundry is still being cooled down.
Clean the fine filter. See
"Cleaning and care".
To delete the message:
Touch the OK sensor.
Replace the fine filter
correctly. See "Cleaning and care".
Switch the dryer off and then
on again.
– Make a note of what is shown
in the display.
– Switch the dryer off and then
on again.
– If a programme still cannot
be started, Call Miele Ser­vice.
You can either unload the drum and leave the laundry to cool at room temperature or leave it in the dryer to continue cooling.
47
Problem solving guide
Problem Possible cause Remedy *
,
Clean out airways
appears after a programme has been cancelled. The laundry is not properly dry.
A prompt which has not been described previously appears in the display.
The cool air intake panel is blocked.
The temperature in the room has risen sharply. To prevent the heat pump overheating, the dryer has cancelled the drying process with a cooling down phase.
An excessive amount of fluff has built up.
A programme cannot be started while there is a fault message in the display.
Move any objects, such as
a laundry basket, away from the grille.
Open a door or window to
keep the room temperature down.
Wait until the room has
cooled down before restarting the programme.
Check and clean the
surfaces of the fluff filters and the fine filter.
Use a vacuum cleaner dusting brush or small crevice nozzle to vacuum up any soiling carefully:
– From the heat exchanger
unit, bottom left (see "Cleaning and care").
– Follow the instructions in
the display.
If a programme still cannot be started, call Miele Ser vice.
-
* To delete a fault message: Switch the dryer off and then on again.
48
Problem solving guide
An unsatisfactory drying result
Problem Possible cause Remedy
The laundry is not sufficiently dry.
Feather filled pillows smell after drying.
Items made of synthetic fibres are charged with static electricity after drying.
There is a build-up of fluff.
* You can alter the drying levels for some programmes (see "Settings menu").
The load consisted of different fabrics.
Feathers are a natural product and this is quite normal.
Synthetic fibres tend to attract static charge.
Fluff is principally the result of friction when garments are being worn and to some extent when they are being washed. Machine drying hardly causes any fluff to form and has no appreciable effect on the lifetime of the fabric.
Finish drying using the
Warm air programme. Select a different
programme next time*.
The smell will dissipate after sufficient airing.
Static charge can be reduced by adding a fabric conditioner to the final rinse in the washing programme or a fabric conditioner sheet to the load when drying.
Fluff is collected by the fluff filters and can be removed easily (see "Cleaning and care").
49
Problem solving guide
Other problems
Problem Possible cause Remedy *
The drying process goes on too long or even switches off.
* Switch the dryer off and then on again before starting the programme.
Ventilation to and from the dryer may be insufficient, e.g. because it is installed in a room which is too small. This can cause the temperature in the room to rise sharply.
Detergent residues, hair
and fine fluff can clog the fluff filters and the fine filters.
– The cooling ribs can be
clogged.
The cool air intake (bottom right grille) is blocked.
The fluff filters and fine filter were wet when replaced.
The laundry has not been spun sufficiently.
The tumble dryer has been overloaded.
Metallic components, e.g. zips have prevented the dryer from registering the correct moisture level in the laundry.
Open a door or window while the dryer is in operation for increased air flow.
Clean the fluff filters and fine
filter. Remove any visible fluff:
. . . From the heat exchanger unit, bottom left, behind the flap in the heat exchanger cavity (see "Cleaning and care"). . . . From the cooling fins behind the grille, bottom right (see this section).
Move any objects, such as a laundry basket, away from the grille.
The fluff filters and fine filter must be dry.
Make sure that your laundry is thoroughly spun at the appropriate spin speed in the washing machine.
Do not exceed the maximum load for the programme selected.
Open zips next time.
If the problem occurs again, dry garments with long zips using the Warm air programme (timed drying).
50
Problem solving guide
Problem Possible cause Remedy
There are humming noises.
The display and the sensors are not lit up and the Start sensor is flashing slowly.
The programme does not start.
Power cut. When power is restored, any programme which was
The display is in a different language.
The interior drum lighting does not come on.
The compressor is operating.
The display and sensor illumination switch off to save energy.
No obvious cause.
running will restart automatically.
A different language has been selected.
The lighting switches off automatically (to save energy).
Access via a code has been activated.
These noises are quite normal and do not indicate a fault.
Touch the Start sensor.
The display and sensors will light up.
See "Settings menu,
Display / keypad illumination".
Is the dryer switched on?
Is the plug correctly
inserted into the socket and switched on?
– Is the door closed
properly?
– Has the fuse or circuit
breaker tripped?
– If you cannot remedy the
problem, then there could be a fault. Contact Miele Service.
Set the language you want. The flag symbol J will guide you.
Switch the dryer off and then on again.
If the lamp needs to be replaced, follow the instructions in "Changing the lamp" at the end of this section.
When the code is entered the lighting will come back on.
51
Problem solving guide
Cleaning the cooling fins (bottom right grille)
In general, the cooling fins do
,
not need cleaning. They should only be cleaned if the drying process is taking an exceptionally long time due to a very high level of dust or fluff in the room in which the dryer is installed.
Use the yellow lever supplied to open the bottom right grille.
To prevent damaging the
,
cooling fins, only pass the vacuum cleaner brush over them lightly, without applying any pressure.
^ Vacuum up any soiling carefully
using a vacuum cleaner dusting brush or small crevice nozzle.
^
Insert the lever in the middle of the gap at the top and lift it up gently (see arrow) until the grille opens out at the top.
^
Now remove the grille by pulling it diagonally upwards.
^
Check whether the cooling fins are clogged.
,
Danger of injury. Do not touch the cooling fins with your hand. You could cut yourself.
52
^
To replace the grille, first insert the bottom of the grille (as shown).
^
Then push the grille firmly into position at the top.
Changing the lamp
Disconnect the tumble dryer from the mains electricity supply.
Problem solving guide
The light specification and maximum wattage is stated on the data plate and on the light cover.
Open the door.
^
You will find the interior light cover at the top of the drum aperture.
^ Insert a suitable tool, such as a wide
bladed screwdriver, under the side edge of the light cover as illustrated.
^
Apply a little pressure and whilst doing so turn your wrist in the direction of the arrow to open the cover.
Turn the light anti-clockwise to
^
remove.
Replace the lamp.
^
To close the cover push it upwards
^
and press it on the left and right until you hear it click into position.
Ensure that it is fitted into
,
position securely, as any moisture could cause a short circuit.
The cover will open downwards.
The temperature resistant lamp should only be ordered from your Miele Dealer or the Miele Spare Parts Department.
53
After Sales service
Repairs
In the event of any faults which you cannot remedy yourself, please contact
your Miele dealer or
the Miele Service Department (see
back cover for contact details).
When contacting your dealer or the Service Department, please quote the model and serial number of your appliance, both of which are shown on the data plate. This is visible when you open the door.
Future updates (PC)
The indicator or check light marked PC on the fascia panel is the interface used by the Miele service technicians during service work for testing purposes and for updating the appliance's programme data.
Appliance guarantee
In the U.K. your appliance is guaranteed for 2 years from the date of purchase. However you must activate your cover by calling 0845 365 6640 or registering online at www. miele.co.uk.
For information on the appliance guarantee specific to your country please contact Miele. See back cover for contact details.
Optional accessories
Optional accessories for this dryer are available from your Miele Dealer, the Miele Spare Parts Department or via the internet at www.miele-shop.com.
N.B. A call-out charge will be applied for service visits where the problem could have been resolved as described in these instructions.
54
Please note that telephone calls may be monitored and recorded for training purposes.
Front view
Installation and connection
a Mains connection cable
b Control panel
c Condensed water container (empty
after every drying programme)
d Door
e Service panel for the fine filter (do
not open during drying)
f Four height adjustable screw feet
g Cool air intake grille (do not obstruct
with a laundry basket or other objects)
h External drainage of condensed
water hose (see "External condensed water outlet")
55
Installation and connection
Rear view
a Protruding lid for holding when
moving the dryer (see arrows)
b Mains connection cable
c Hose for external drainage of
condensed water
d Accessories for connection to a sink
drain outlet
If transporting the dryer at an
,
angle, only tip it towards its left side.
Transporting the dryer
When moving the dryer, hold it by the lid where it protrudes to the rear. To manoeuvre the dryer out of its packing case to its installation site you will also need to hold it by the front feet.
,
Only transport the dryer as shown in the following illustrations.
56
,
If the tumble dryer has not been transported as described, then it must be left to stand for at least 1 hour before electricity supply. Otherwise the heat pump can be damaged.
it is connected to the
Installation site
Make sure the dryer door can be
,
opened without hindrance after installation.
The cool air intake panel at the
,
front of the dryer must not be blocked or covered, e.g. by a laundry basket, as this would cause a fault.
Building under a continuous worktop/ in a row of kitchen units
It is very important to avoid a
,
build-up of heat. The warm air which is expelled from the rear of the dryer must be able to dissipate. Warm air which cannot dissipate could cause a fault.
A build-up of heat can be avoided by:
Adjusting the screw feet so that there is a gap of at least 20 mm between the floor and the bottom of the dryer.
Creating a gap for the dryer in the kitchen furniture plinth facing.
Creating ventilation gaps in the kitchen unit.
N.B. When built under, drying times may be longer.
Installation and connection
The dryer should not be installed
,
next to a refrigeration appliance. The warm air expelled from the rear of the dryer would increase the temperature around the refrigeration appliance's heat exchanger causing the compressor to run continuously. If it is not possible to install the dryer anywhere else, then the refrigeration appliance must be sealed off from the dryer.
A building-under kit (Miele
,
accessory, available to order) with a coverplate to replace the appliance´s lid is required. It must be fitted by a suitably qualified person to ensure electrical safety.
N.B. If you wish to push the tumble dryer under a worktop and there is space to do this without removing the lid the building-under kit is not necessary. Otherwise the building-under kit is essential.
The building-under kit is supplied with its own installation instructions.
N.B. When built under, drying times may be longer.
The electrical socket must be located in an accessible position near the appliance.
With niche heights of:
830-840 mm, longer screw feet* are required.
870-885 / 915-930 mm, one or two raising kits* are required.
* Miele accessory available to order
57
Installation and connection
Levelling the appliance
The appliance must be perfectly level to ensure safe and proper operation.
Before moving the tumble dryer again (e.g. when moving house)
After each use a small quantity of condensed water will collect in the area around the pump. This water can run out if the tumble dryer is tipped up when it is being moved. It is a good idea to run the Cool air programme for approximately 1 minute before moving it. Any remaining condensed water will then be fed into the condensed water container or out through the drain hose.
Washer-dryer stack
The tumble dryer can also be combined with a Miele washing machine in a washer-dryer stack. The appropriate "WTV" stacking kit* to match your dryer is required.
* Miele accessory available to order
,
Stacking kits must only be installed by a suitably qualified fitter.
^
The screw feet can be adjusted to compensate for any unevenness in the floor.
,
Do not block the gap between the bottom of the tumble dryer and the floor with plinth facings, deep pile carpet etc. This would hinder a sufficient flow of air to the dryer.
58
Installation and connection
External condensed water outlet
General notes
When drying is in progress, condensed water is pumped into the condensed water container through the drain hose at the back of the dryer. The condensed water can also be drained off directly if the tumble dryer is installed near a sink, drain outlet etc. so that the condensed water container does not have to be emptied.
Drain hose length ............1.50 m
Maximum delivery head .......1.50 m
Maximum drain hose length ....4.00 m
If the on-site water drainage
,
system is not fitted with a non-return valve or an appropriate air gap, one must be fitted to prevent the risk of back-flow. (See "Installation conditions requiring a non-return valve").
There will be a small amount of
^
residual water in the drain hose. Have a container ready to collect this.
^ Pull the hose off its connection (see
arrow).
^ Allow any residual water to run into
the container.
^ Unwind the hose and pull it carefully
out of the holders.
The following optional accessories are available:
an extension hose
a non-return valve kit for connection to an external condensed water outlet (includes an extension hose). Maximum delivery head with non-return valve fitted: 1.00 m
Arranging the drain hose
,
Do not pull on the drain hose and do not stretch it or allow it to become kinked as it could get damaged.
^
Position the hose to the right or left hand side as necessary.
Leave the hose in the middle holder to prevent it from becoming kinked inadvertently.
59
Installation and connection
External drainage via a sink or gully
See "Front view" illustration.
^
If you want to drain the water off
,
into a sink you will need to secure the hose carefully, e.g. by tying it to a tap to make sure it cannot slip during use. Otherwise there is a risk of overflowing water which could cause damage.
Use the bow-shaped guide to
^
prevent the drain hose from becoming kinked.
Installation conditions requiring a non-return valve
Certain installation conditions
,
require the fitting of a non-return valve for external water connection (available as an
optional accessory). A non-return valve will prevent the risk of back-flow out of the dryer which could cause damage.
Example: Connection to a sink drain outlet
The drain hose with non-return valve fitted can be connected directly to a suitable sink drain outlet.
^ Remove the following from the back
of the dryer at the top: Adapter 1 and hose clip 3 behind it.
A non-return valve is required:
If the tumble dryer is connected to a sink drain outlet (see the following section).
If the tumble dryer is connected to a drainage system already in use by another appliance, e.g. a dishwasher or washing machine.
60
1 Adapter
2 Nut
3 Hose clip
4 End of the hose
5 Non-return valve
6 Tumble dryer drain hose
Installation and connection
Fit adapter 1 to the sink drain outlet
^
using nut 2.
If this nut has a flat disc in it you should take the disc out first.
Attach the end of hose 4 to adapter
^
1.
Use a screwdriver to tighten hose
^
clip 3 up close to the nut.
Non-return valve 5 has to be
,
fitted with the arrow pointing in the direction of flow (i.e. towards the sink). Otherwise water will not drain out of the appliance.
^ Fit non-return valve 5 to tumble dryer
drain hose 6 (make sure it is fitted in the correct direction - see arrow on non-return valve).
^ Secure the non-return valve using
hose clips.
61
Electrical connection
Electrical connection U.K.
All electrical work should be carried out by a suitably qualified and competent person, in strict accordance with current national and local safety regulations (BS 7671 in the UK).
Ensure power is not supplied to the appliance until after installation work has been carried out.
The appliance is supplied with a mains cable with moulded plug ready for connection to a 230-240V mains supply. Please ensure the connection data quoted on the data plate match the household mains supply.
Connection should be made via a suitable switched socket which is easily accessible after installation.
For extra safety it is advisable to protect the appliance with a suitable residual current device (RCD). Contact a qualified electrician for advice.
Non-rewireable plugs BS 1363
The fuse cover must be refitted when changing the fuse, and if the fuse cover is lost, the plug must not be used until a suitable replacement is obtained. The colour of the correct replacement cover is that of the coloured insert in the base of the plug, or the colour that is embossed in words on the base of the plug (as applicable to the design of plug fitted).
Replacement fuses should be ASTA approved to BS 1362 and have the correct rating. Replacement fuses and fuse covers may be purchased from your local electrical supplier.
WARNING: THIS APPLIANCE MUST BE EARTHED
Do not connect via an extension lead. Extension leads do not guarantee the required safety of the appliance (e.g. danger of overheating).
62
Consumption data
1
Load
Cottons Normal
Cottons Normal 8.0
Cottons Normal + Gentle tumble + Freshen up Cottons Hand iron rr 8.0
Minimum iron Normal 3.5 1200 40 0.60 51 Minimum iron Normal + Gentle tumble + Freshen up Minimum iron Hand iron 3.5 1200 40 0.50 45 Automatic plus Normal 5.0 800 50 1.35 109 Shirts Normal + Gentle tumble Hygiene Normal 3.5 1000 60 1.70 140 Gentle smoothing 1.0 1000 60 0.30 30 Proofing Normal 2.0 800 50 1.20 99 Outerwear Normal 2.5 800 50 0.95 80 Denim Normal + Gentle tumble Express Normal 3.5 1000 60 1.00 82 Woollens 2.0 1000 50 0.15 20
1
Weight of dry laundry
2
Test programme in accordance with Regulation 392/2012/EU for energy labelling measured in
accordance with EN 61121. All data was calculated using EN 61121 unless otherwise stated.
Notes for test institutes:
When selecting the Cottons programme, drain the condensed water away through the drainage hose.
Before testing in accordance with EN 61121, drya3kgload of cotton laundry with 70% residual moisture as per the above standard using the Cottons Normal programme without any extra options.
Consumption data can vary from the nominal values given above depending on the size of the load, types of textiles, residual moisture levels after spinning, fluctuations in the electricity supply and any extra options selected.
2
kg rpm % kWh min.
8.0
4.0
8.0
8.0
8.0
8.0
3.0
8.0
8.0
8.0
8.0
3.5
3.5
2.0
2.0
3.0
3.0
Final spin speed in a
domestic washing machine
1000 1000 1200 1400 1600 1800
1000 1000 1000 1200 1400 1600 1800
1200 1200
600 600
900 900
Residual moisture
60 60 53 50 44 43
60 60 60 53 50 44 43
40 40
60 60
60 60
Energy Duration
2.02
1.11
1.80
1.70
1.55
1.50
2.05
0.95
1.40
1.20
1.15
0.95
0.95
0.60
0.65
0.70
0.75
1.30
1.40
154
89 139 132 118 116
153
75 111
97
91
77
75
53
52
57
60
107 115
63
Technical data
Height 850 mm
Width 595 mm
Depth 596 mm
Depth with door open 1071 mm
Height for building under 820 mm
Width for building under 600 mm
Depth for building under 600 mm
Suitable for pushing under a worktop
Suitable for stacking yes
Weight 61 kg
Drum volume 111 litres
Maximum capacity 1-8 kg dry weight
Capacity of condensed water container
Drain hose length 1.5 m
Maximum delivery head 1.5 m
Maximum drain hose length 4 m
Length of connection cable 2 m
Voltage
Connected load
Fuse rating See data plate
Lamp wattage
Test certificates awarded
Energy consumption see "Consumption data"
yes
Approx. 4.2 litres
64
The Settings menu is used to alter the dryer's electronics to suit different requirements. Settings can be altered at any time.
Open the Settings menu
Settings menu
To select a setting
Language J
Main menu
\
$ Settings ! # Favourite programmes
\
# Cottons
\
Use the top right hand sensor to select the Settings
^
menu.
^ Confirm with
Settings
\
$ Language ! # Time
\
! Drying levels
\
^ The sensors on the right can be used to scroll up or down
the list.
The display can be set to appear in one of several different languages.
OK.
10:21
m
!
10:21
m
[
[
[
[
To select the language you want, go to the Language J sub-menu.
The flag after the word Language acts as a guide to prevent a language which will not be understood from being set.
65
Settings menu
Time
Clock format
The time can be set to appear as a 24 hour or 12 hour clock. You can also use this setting to adjust the time of day.
Set the time of day
Drying levels
Time
\
$ 24 h clock ( # 12 h clock
\
Select the format you want.
^
The dryer is delivered with the clock format set as a 24 hour clock.
Time
10 :21
^ Use the
^
Confirm the hours with
You can alter the drying levels for the Cottons, Minimum iron and Automatic plus programmes.
+ and - sensors to set the hour.
OK and then enter the minutes.
10:21
OK !
+ $
- #
OK !
[
[ [ [
66
The bars show you the setting. The default is: the middle setting.
Drier
P P P P P P P
the programme duration increases.
Damper the programme duration is shorter.
P
Code
To activate the code
Settings menu
The code prevents the dryer being used without your knowledge.
When the code has been activated, you have to enter a code after switching the dryer on. Otherwise the dryer cannot be operated.
The door can be opened and items removed at any time.
The display will now request that a code is entered. The code is 250 and cannot be altered.
Activate code
2 A A
Please enter code OK !
^ Use + to enter the first number.
^ Confirm the first number with
number. Repeat the process until all three numbers have been entered.
^
After the last number has been entered, you must confirm the code with
Information
0
^
Confirm with
^
Switch the dryer off.
OK.
Input OK. Code active when machine is switched off.
OK.
OK and then enter the second
10:21
+ $
#
10:21
OK !
[ [ [
[
67
Settings menu
To use the dryer when the lock code is activated
When the dryer is switched on again, the display will request the code.
^
The dryer is now unlocked and ready for use.
To deactivate the code
^
^ Confirm with
You can now switch on the dryer without being asked to enter a code.
Enter code 250 with the
Proceed as for activating the code.
Information
1
Code OK. Ready
OK.
+ and - sensors.
OK !
[
68
Settings menu
Buzzer
When the buzzer function has been activated, an audible tone sounds at the end of a programme.
Off
Factory default
The buzzer is switched off but sounds at maximum volume if there is a fault.
Normal
The buzzer sounds at the end of a programme.
Loud
The buzzer sounds louder at the end of a programme.
Keypad tone
An audible tone sounds each time a button is pressed.
If you make an alteration it will appear in the display immediately.
Display / keypad illumination
The display and sensor illumination switches off to save energy.Start flashes slowly to save energy.
The display and the sensors are not illuminated.
if a programme is not selected within
10 minutes of the tumble dryer being switched on.
– 10 minutes after the end of a
programme.
Press the Start sensor to activate the display and sensor illumination again.
Off after 10 minutes
The display and sensor illumination will switch off 10 minutes after the programme has started.
Off
Factory default
On
Brightness
Contrast
The display contrast and brightness can be altered in stages.
The bars which level is set.
PPPPPPPshow you
"On" whilst programme is running
Factory default
The display and sensors remain lit up whilst the programme is running.
69
Settings menu
Memory
The electronics will memorise the drying level and some of the extra options selected for the current drying programme and the duration of a timed drying programme.
When the programme is chosen again these settings will appear in the display.
Off
Factory default
On
Anti-crease
Anti-crease helps prevent creasing, if laundry is not normally removed im­mediately after the end of a programme.
After the programme has finished, the drum will continue to rotate at intervals.
There is no anti-crease phase with Wollens.
Off
1 hour
2 hours
(Factory default)
70
Optional accessories for this dryer are available from your Miele Dealer or from the Miele Spare Parts Department,
or via the internet at www.miele-shop.com.
Fragrance flacon
For a pleasant fragrance when drying your laundry.
Holder for fragrance flacon
The holder is required to fit the fragrance flacon to the fluff filter.
The holder comes with its own instructions.
Optional accessories
Dryer basket
This enables items which must not be subjected to mechanical action to be dried or aired.
The dryer basket comes with its own instructions.
71
Alteration rights reserved/0113
M.-Nr. 09 459 300 / 02
Loading...