Operating and installation instructions
Fridge-freezer
To avoid the risk of accidents or damage to the appliance it is essential
to read these instructions before it is installed and used for the first time.
en-GBM.-Nr. 11 450 550
Contents
Warning and Safety instructions.......................................................................... 5
Caring for the environment ................................................................................14
Saving energy ...................................................................................................... 15
Guide to the appliance........................................................................................ 17
Control panel......................................................................................................... 17
This refrigeration appliance complies with current safety
requirements. Inappropriate use can, however, lead to personal
injury and material damage.
Please read the operating and installation instructions carefully
before using the refrigeration appliance for the first time. They
contain important information on safety, installation, use and
maintenance. This is to protect yourself from injury, and from
damaging your refrigeration appliance.
In accordance with standard IEC60335-1, Miele expressly and
strongly advises that you read and follow the instructions in the
chapter on installing the appliance as well as the safety
instructions and warnings.
Miele cannot be held liable for injury or damage caused by noncompliance with these instructions.
Keep these instructions in a safe place and pass them on to any
future owner.
Correct application
This refrigeration appliance is intended for use in the home and in
similar environments, for example
– in shops, offices and similar work settings
– by the guests in hotels, motels, bed & breakfasts and other typical
home settings.
This refrigeration appliance is not intended for outdoor use.
This appliance is intended for domestic use only for cooling and
storing food and drink as well as for storing deep frozen food,
freezing fresh food and for making ice.
Any other usage is not supported by the manufacturer and could be
dangerous.
5
Warning and Safety instructions
This refrigeration appliance is not suitable for storing and keeping
cool medicines, blood plasma, laboratory preparations or similar
substances or products that are subject to the the Medical Device
Directive. Incorrect use of the refrigeration appliance for such
purposes may cause deterioration of the items stored. The
refrigeration appliance is also not suitable for use in areas where
there is a risk of explosion.
Miele cannot be held liable for damage caused by improper or
incorrect use or operation of the appliance.
The appliance can only be used by people with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge,
if they are supervised whilst using it, or have been shown how to use
it in a safe way and recognise and understand the consequences of
incorrect operation.
Safety with children
Children under 8 years of age must be kept away from the
refrigeration appliance unless they are constantly supervised.
Children 8 years and older may only use the appliance
unsupervised if they have been shown how to use it in a safe way
and recognise and understand the consequences of incorrect
operation.
Children must not be allowed to clean or maintain the appliance
unsupervised.
Please supervise children in the vicinity of the appliance and do
not let them play with it.
Danger of suffocation! Whilst playing, children could become
entangled in packaging (such as plastic wrapping) or pull it over their
head and suffocate. Keep packaging material away from children.
6
Warning and Safety instructions
Technical safety
The coolant circuit has been checked for leaks. The refrigeration
appliance complies with statutory safety requirements and the
appropriate EU directives.
This refrigeration appliance contains the coolant Isobutane
(R600a), a natural gas which is environmentally friendly. The coolant
does not damage the ozone layer and does not contribute to the
greenhouse effect.
The use of this coolant has, however, led to a slight increase in the
noise level of the appliance. In addition to the noise of the
compressor, you might be able to hear the coolant flowing around
the cooling circuit. Unfortunately, this cannot be avoided, but it does
not affect the performance of the refrigeration appliance.
When transporting and installing the refrigeration appliance, ensure
that no parts of the cooling circuit are damaged. Splashes of coolant
can damage the eyes.
In the event of damage:
– Avoid naked flames or anything which creates a spark.
– Disconnect the refrigeration appliance from the mains electricity
supply.
– Ventilate the room where the refrigeration appliance is located for
several minutes.
– Contact the Miele Customer Service Department.
The more coolant there is in a refrigeration appliance, the larger
the room it should be installed in. In the event of a leakage, if the
appliance is in a small room, there is the danger of combustible
gases building up. For every 11 g of coolant at least 1m3 of room
space is required. The amount of coolant in the appliance is stated
on the data plate inside the appliance.
7
Warning and Safety instructions
To avoid the risk of damage to the appliance, make sure that the
connection data (fuse rating, frequency and voltage) on the data
plate corresponds to the household supply.
Check that this is the case before connecting the appliance. Consult
a qualified electrician if in any doubt.
The electrical safety of this appliance can only be guaranteed
when correctly earthed. It is essential that this standard safety
requirement is met. If in any doubt please have the electrical
installation tested by a qualified electrician.
Reliable and safe operation of this appliance can only be assured
if it has been connected to the mains electricity supply.
If the electrical connection cable is faulty it must only be replaced
by a Miele authorised service technician to protect the user from
danger.
Do not connect the appliance to the mains electrical supply by a
multi-socket adapter or extension lead. These are a fire hazard and
do not guarantee the required safety of the appliance.
If moisture gets into electrical components or into the mains
connection cable, it could cause a short circuit. Therefore, do not
operate this refrigeration appliance in areas which are exposed to
moisture (e.g in a garage or utility room).
This appliance must not be used in a non-stationary location (e.g.
on a ship).
Do not use a damaged appliance. It could be dangerous. Check
the appliance for visible signs of damage.
For safety reasons, this appliance may only be used after it has
been built in.
The appliance must be disconnected from the power supply
during installation, maintenance and repair work, and during
installation work on the mains water connection. It is only completely
isolated from the power supply when:
8
Warning and Safety instructions
– the mains fuses are switched off, or
– the screw-out fuse is removed (where applicable), or
– the mains cable has been unplugged. Pull on the plug and not the
cable when disconnecting it from the power supply.
Unauthorised installation, maintenance and repairs, or a faulty
mains water connection can cause considerable danger for the user.
Installation, maintenance and repairs, installation work on the mains
water connection, and all repairs on the ice/water outlet must only
ever be carried out by a Miele-authorised technician.
The ice-cube maker must only be connected to a cold water
supply.
Miele cannot be held liable for damage caused by a faulty mains
water connection.
While the appliance is under warranty, repairs should only be
undertaken by a Miele authorised service technician. Otherwise the
warranty is invalidated.
Miele can only guarantee the safety of the appliance when
genuine original Miele replacement parts are used. Faulty
components must only be replaced by Miele spare parts.
Correct use
The appliance is designed for use within a certain climate range
(ambient temperatures), and should not be used outside this range.
The climate range for your appliance is stated on the data plate
inside the appliance. Installing it in a room with too low an ambient
temperature, e.g. a garage, will lead to the appliance switching off
for longer periods so that it cannot maintain the required
temperature.
Do not cover or block the air vents as this could impair the
efficiency of the appliance, increase the electricity consumption and
could cause damage to the components.
9
Warning and Safety instructions
If storing food which contains a lot of fat or oil in the appliance or
the door, make sure that it does not come into contact with plastic
components as this could cause stress cracks or break the plastic.
Risk of fire and explosion. Do not store explosive materials in the
refrigeration appliance or any products containing propellants (e.g.
spray cans). Electrical components can cause flammable mixes of
gases to ignite.
Danger of explosion. Do not operate any electrical equipment (e.g.
an electric ice-cream maker) inside the refrigeration appliance.
Danger of sparking and explosion.
Do not store cans or bottles containing carbonated drinks or
liquids which could freeze in the freezer. The cans or bottles could
explode. Danger of injury and damage to the appliance.
When cooling drinks quickly in the freezer, make sure bottles are
not left in for more than one hour; otherwise they could burst,
causing injury or damage.
Danger of injury. Never handle frozen food or the metal parts of
the appliance with wet hands. Your hands may freeze to the frozen
food or to the metal.
Danger of injury. Do not take ice cubes out with your bare hands
and never place ice cubes or ice lollies in your mouth straight from
the freezer zone. The very low temperature of the frozen food can
cause frost burn to the lips and tongue.
Do not refreeze partially or fully defrosted food. Consume
defrosted food as soon as possible, as it will lose its nutritional value
and spoil if left for too long. Defrosted food may only be re-frozen
after it has been cooked.
10
Warning and Safety instructions
Observe the manufacturer's “use-by” dates and storage
instructions given on food to avoid the risk of food poisoning.
Storage times will depend on several factors, including the freshness
and quality of the food, as well as the temperature at which it is
stored.
Only use genuine original Miele accessories and spare parts with
this appliance. Using accessories or spare parts from other
manufacturers will invalidate the warranty, and Miele cannot accept
liability.
Cleaning and care
Do not use any oils or grease on the door seals, as these will
cause the seals to deteriorate and become porous with time.
Do not use a steam cleaning appliance to clean or defrost this
appliance.
Steam could reach electrical components and cause a short circuit.
Sharp edged or pointed objects will damage the evaporator,
causing irreversible damage to the appliance. Do not use sharp
edged or pointed objects to
– remove frost and ice,
– separate frozen foods or remove ice trays.
Do not place electric heaters or candles in the appliance to
defrost it. These can damage the plastic parts.
Do not use defrosting sprays or de-icers, as they could contain
substances which could damage the plastic parts or which might
cause the build-up of gases and pose a danger to health.
Rinse the ice cube maker and the water pipes:
– before using for the first time,
– if the ice cube maker has not been used for a long time,
11
Warning and Safety instructions
– regularly when in continuous use (at least once a month), to
remove ice residues from the system (to avoid a blockage of the
water supply) and
– before switching the ice cube maker off for a long time.
Transport
Always transport the appliance in an upright position and in its
original transport packaging to avoid damage in transit.
Danger of injury and damage to the appliance. The refrigeration
appliance is very heavy and must be transported by two people.
12
Warning and Safety instructions
Disposal of your old appliance
If your old refrigeration appliance has a door lock, destroy it. This
will prevent the risk of children playing accidentally locking
themselves in and endangering their lives.
Splashes of coolant can damage the eyes. Be careful not to
damage any part of the pipework whilst awaiting disposal, e.g. by
– puncturing the coolant channels in the condenser,
– bending any pipework, or
– scratching the surface coating.
Symbol on the compressor (depending on model)
This information is only relevant for recycling. There is no risk during normal
operation.
The oil in the compressor can be fatal if swallowed or if it
penetrates the airways.
13
Caring for the environment
Disposal of the packing
material
The packaging is designed to protect
the appliance from damage during
transportation. The packaging materials
used are selected from materials which
are environmentally friendly for disposal
and should be recycled.
Recycling the packaging reduces the
use of raw materials in the
manufacturing process and also
reduces the amount of waste in landfill
sites.
Disposing of your old
appliance
Electronic and electrical appliances
contain many valuable materials. They
also contain certain materials,
compounds and components which
were essential for their correct
functioning and safety. These could be
hazardous to your health and to the
environment if disposed of with general
waste or if handled incorrectly. Please
do not, therefore, dispose of your old
appliance with general waste.
responsible for deleting any personal
data from the appliance prior to
disposal.
Take care not to damage your
refrigeration appliance’s pipework
before or during transportation to an
authorised collection depot.
This is to ensure that coolant in the
cooling circuit and oil in the compressor
is contained, and will not leak into the
environment.
Please ensure that your old appliance
poses no risk to children while being
stored prior to disposal. For further
information, see “Warning and Safety
instructions” in these operating and
installation instructions.
Instead, please make use of officially
designated collection and disposal
points to dispose of and recycle
electrical and electronic appliances in
your local community, with your dealer
or with Miele. By law, you are solely
14
Saving energy
Installation /
Maintenance
Temperature
setting
Normal energy
consumption
In a ventilated room.In an enclosed, unventilated
Protected from direct
sunlight.
Not near to a heat source
(radiator, oven).
Where the ideal ambient
room temperature is approx.
20°C.
Ventilation gaps uncovered
and dusted regularly.
Refrigerator section 4 to
5°C
PerfectFresh Pro zone just
above 0 °C
Freezer section -18°C
Increased energy
consumption
room.
In direct sunlight.
Near to a heat source
(radiator, oven).
Where the ambient room
temperature is above 25°C.
Ventilation gaps covered or
dusty.
The lower the temperature,
the higher the energy
consumption.
15
Saving energy
Normal energy
consumption
UseDrawers and shelves
arranged as they were when
the appliance was delivered.
Only open the door when
necessary and for as short a
time as possible. Store food
in an organised way.
Take an insulated cool bag
when shopping, and load
food in the appliance as
soon as possible.
Replace any food removed
as quickly as possible,
before it warms up too
much.
Allow hot food and drinks to
cool down before placing
them in the appliance.
Store food well packaged or
covered.
Increased energy
consumption
Frequent opening of doors
for long periods will cause a
loss of coldness. The
appliance will try to cool
down and the compressor
will run for longer periods.
Hot food or food at room
temperature raises the
temperature inside the
appliance. The appliance will
try to cool down and the
compressor will run for
longer periods.
The evaporation or
condensation of liquids in
the refrigerator section will
cause a loss of coldness.
16
Place frozen food in the
refrigerator to defrost.
Do not over-fill the appliance
to allow air to circulate.
Poor air circulation will
cause a loss of coldness.
Control panel
Guide to the appliance
a
For switching the
whole cooling appliance on and off
b
Optical interface
(for Service technicians only)
c
For selecting the refrigerator and
freezer sections
d
For switching the SuperCool and
SuperFreeze functions on and off
e
For setting the temperature
( = colder),
selection button in settings mode
f
For confirming a selection (OK
button)
g
For setting the temperature
( = warmer),
selection button in settings mode
h
For selecting and deselecting
settings mode
i
For switching the temperature or
door alarm off
j
Display with temperature and
symbols (symbols only visible in
settings mode, in the event of an
alarm/message; see table for
explanation of symbols)
17
Guide to the appliance
Symbols
SymbolMeaningFunction
Safety lockPrevents the appliance being switched off,
the temperature being altered, Super cool
and Super freeze being switched on and
settings being altered by mistake.
Ice cube makerFor switching the ice cube maker on and
off; for setting the water volume; for rinsing
the ice cube maker; for setting the cleaning
position of the ice cube tray; flashes if there
is a fault with the ice cube maker
Audible tonesChoice of sensor tone and door and
temperature alarm tone
Miele@homeOnly visible when a communication module
or communication stick is fitted and signed
on
Display brightness
settings
Charcoal filter
replacement indicator
(Active AirClean)
PerfectFresh Pro
temperature
Sabbath modeFor switching Sabbath mode on and off
Mains connectionConfirms that the appliance is connected to
Alarm
(only visible when the
door or temperature
alarm sounds)
Demo mode
(only visible when
Demo mode is
switched on)
18
For adjusting the brightness of the display
This function must be activated after fitting
a charcoal filter; it lights up to remind you to
replace it
For altering the temperature in the
PerfectFresh Pro zone
the electricity supply when it is not
switched on; flashes in the event of a
power cut
Lights up when there is a door alarm;
flashes when there is a temperature alarm,
power cut or other fault
For switching off Demo mode
Guide to the appliance
a
Control panel
b
Fan
c
Egg tray / door shelf
d
Adjustable shelf
e
Adjustable shelf with
lighting (FlexiLight)
f
Bottle shelf
g
PerfectFresh Pro zone
interior lighting
h
PerfectFresh Pro zone, dry
compartment
i
Condensate channel and drain hole
j
Regulator for setting the moisture
level in the humidity-controlled
compartment
k
PerfectFresh Pro zone, humiditycontrolled compartment
l
Ice-cube drawer with automatic icecube maker
m
Freezer drawers
The PerfectFresh Pro zone satisfies
the requirements of a chill
compartment to ENISO15502.
19
Accessories
Accessories supplied
Bottle holder
The flexible ribs grip the bottles
securely when the door is opened and
closed.
Butter dish
Cool pack
The cool pack prevents the temperature
in the freezer section from rising too
quickly in the event of a power cut. This
can help prolong the storage life.
The cool pack will be at its most
effective after it has been in the freezer
for approx. 24hours.
Optional accessories
A range of useful Miele accessories and
care products are available for your
appliance.
Accessories are available to order via
the Miele Webshop, from Miele
directly (see back cover for contact
details) or from your Miele dealer.
Egg tray
20
Multi-purpose microfibre cloth
The microfibre cloth is suitable for
removing fingerprints and light soiling
from surfaces such as stainless steel,
glass, plastic and chrome without the
use of chemicals.
Accessories
MicroCloth Kit
The MicroCloth Kit contains a universal
cloth, a glass cloth and a polishing
cloth.
These cloths are extremely rip-proof
and hard-wearing. Thanks to very fine
microfibres these cloths achieve
excellent cleaning results.
Bottle rack
Bottles can be stored horizontally using
the bottle rack to save space.
The bottle rack can be placed at
different positions in the appliance.
KKF-FF Active AirClean charcoal
filters with holder
Charcoal filters neutralise unpleasant
odours in the refrigerator section for
improved air quality.
The charcoal filter holder clips onto the
protective strip at the back of the shelf
and can be moved as necessary.
Now activate the filter reminder in
settings mode (see “Selecting further
settings” - Filter replacement
indicator“).
KKF-RF
ActiveAirClean replacement filters
Replacement filters to the fit the Active
AirClean holder are available. We
recommend replacing the charcoal
filters every 6months.
21
Accessories
XKS3130W WiFi stick
(Miele@home)
The WiFi stick enables your refrigeration
appliance to communicate, so that you
can access appliance data at any time
with a smartphone or tablet (iOS® or
Android™ operating systems).
To use the Miele@mobile app or
Miele@home features, such as the
option to switch on SuperCool/
SuperFreeze, you must insert the WiFi
stick into your Miele refrigeration
appliance and connect it to your WiFi
network.
Fitting and installation instructions for
the stick are supplied with it and
describe how to install the WiFi stick
and connect to a WiFi network.
22
Switching on and off
Before using for the first time
Packaging material
Remove all packaging material from
the inside of the appliance.
Protective foil
The stainless-steel trim on the interior
shelves and door shelves in the
appliance has a layer of protective foil
to prevent scratching in transit.
Remove this protective foil once the
appliance has been installed.
Cleaning the appliance
Please refer to the relevant
instructions in “Cleaning and care”.
Clean the inside of the appliance and
the accessories.
Clean the ice-cube maker: after
selecting the “Rinse the ice-cube
maker” setting, the ice-cube
maker and the water supply pipework
will be rinsed automatically with
water.
Operating the appliance
A light touch of the finger on the
sensors is all that is required to operate
this appliance.
A tone will sound each time a sensor is
touched. You can deactivate this, if you
wish (see “Selecting further settings Audible tones”).
Switching on
When the appliance is connected to the
electrical supply, the mains connection
symbol will appear in the display
after a short while.
Touch the On/Off sensor.
The mains connection symbol goes
out and the appliance starts to cool
down.
The sensor controls for the available
cooling sections appear in the control
panel:
The refrigerator section sensor control
is highlighted in yellow and the current
temperature in the refrigerator appears
in the display.
23
Switching on and off
When the refrigerator section door is
opened, the interior lighting comes on
and the LED lighting on the adjustable
shelves becomes brighter until it
reaches its maximum brightness.
When the appliance is switched on for
the first time, the sensor control for the
freezer section and the alarm
symbol will flash until the set freezer
temperature is reached.
When the set freezer temperature is
reached, the sensor control for the
freezer section lights up constantly and
the alarm symbol goes out.
To enable the temperature to get
sufficiently cold inside the appliance,
allow the appliance to run for a few
hours before placing food in it. Do not
place food in the freezer until it has
reached the required coldness (at
least -18°C).
Individual settings can be set for each
section.
Touch the sensor control for the
section you want to adjust the
settings for.
The sensor control that has been
selected is highlighted in yellow.
The SuperCool function can be
selected or the temperature can be
adjusted for the refrigerator section.
For the freezer section, the
SuperFreeze function can be selected
or the temperature can be adjusted.
Please refer to the relevant sections for
more information.
If another section is then selected, the
settings for the previously selected
section will remain unchanged.
24
Switching on and off
Switching off
Touch the On/Off control.
If this does not work, the safety lock
is activated.
The temperature display will go out and
the mains connection symbol will
appear.
The interior lighting goes out and
cooling is turned off.
Switching off the refrigerator section
separately
The refrigerator section can be
switched off without having to switch
off the freezer section. This is useful,
e.g. whilst on holiday.
Switching the refrigerator section
back on again
The refrigerator section can also be
switched back on again separately.
Touch the sensor for the refrigerator
section so that it is highlighted in
yellow again.
The temperature display for the
refrigerator section lights up. The
refrigerator section starts to cool and
the interior lighting comes on when the
door is opened.
Touch the sensor for the refrigerator
section so that it is no longer
highlighted.
Dashes will appear briefly in the display.
25
Switching on and off
Switching off for longer
periods of time
If, during a long absence, the
refrigeration appliance is switched off
but not cleaned and the door(s) left
shut, there is a risk of mould forming
inside the appliance.
It is essential to clean the
refrigeration appliance.
If the refrigeration appliance is not
going to be used for a longer period of
time, observe the following:
Switch the refrigeration appliance off.
Switch off at the wall socket and
withdraw the plug from the socket, or
disconnect the fuse.
Empty the ice-cube drawer.
Risk of damage to the ice-cube
maker.
If the water inlet is blocked while the
ice-cube maker is still in use, the
water inlet pipe can freeze up.
Turn the ice-cube maker off if the
water supply is turned off (e.g. while
on holiday).
Close the stopcock for the water
inlet.
Clean the refrigeration appliance and
leave the door ajar to air the
appliance and avoid odours building
up inside.
It is also advisable to carry out the last
two instructions if you are switching
the refrigerator section off for a longer
period of time.
26
The correct temperature
It is very important to set the correct
temperature for storing food in the
appliance. Bacteria will cause food
which is not stored at the correct
temperature to deteriorate rapidly.
Temperature influences the growth rate
of these bacteria. Reducing the
temperature reduces their growth rate.
The temperature in the refrigeration
appliance will rise:
– The more often the appliance door is
opened and the longer it is kept open
– The more food that is stored in it
– The warmer the food is which is
being put into it
– The higher the ambient temperature
surrounding the refrigeration
appliance. This refrigeration
appliance is designed for use within
specific ambient temperatures
(climate range). Do not use in
ambient temperatures for which it is
not designed.
Automatic temperature distribution
(DynaCool)
The fan switches on automatically when
the cooling system for the refrigerator
switches on. It distributes the
temperature in the appliance to all areas
more evenly so that all the food will be
chilled to about the same degree.
...in the freezer section
To freeze fresh food and to store frozen
food for long periods, a temperature of
-18°C is required. At this temperature
the growth of bacteria is generally
halted. As soon as the temperature
rises above -10°C, the bacteria
become active in the food again so it
cannot be kept as long. For this reason,
partially defrosted or defrosted food
must not be re-frozen. Food may be refrozen once it has been cooked , as the
high temperatures achieved when
cooking destroy most bacteria.
... in the refrigerator section
and in the PerfectFresh Pro
zone
We recommend a temperature of 4°C
in the refrigerator section.
The temperature in the PerfectFresh Pro
zone is controlled automatically and
maintained at 0 to 3°C.
27
The correct temperature
Temperature display
In normal operation the display shows
the average, current temperature inthe refrigerator section and the
temperature in the warmest area ofthe freezer section.
If the temperature in the freezer section
is not within the normal temperature
display range, dashes will flash in the
display.
Depending on the ambient temperature
and the temperature setting, it can take
the appliance a few hours to reach the
temperature required and for this
temperature to then be shown as a
constant temperature in the display.
Setting the temperature in the
refrigerator / freezer sections
The temperatures for the refrigerator
and freezer sections are set
independently of one another.
Select the refrigerator or the freezer
section.
Use the two sensors underneath the
display to set the temperature.
By touching the sensor
– the temperature will get colder
28
– the temperature will get warmer.
The temperature being set will flash in
the display.
The correct temperature
The following information shows in the
display while the sensors are being
touched:
– Touching a sensor once: the last
temperature selected flashes.
– Each subsequent touch of the
sensor: adjusts the temperature
shown in 1°C steps.
– Leaving a finger on the sensor
changes the temperature
continuously.
Approximately 5 seconds after the last
time a sensor has been touched, the
current temperature inside the
appliance is automatically shown.
Or
Touch the OK sensor to confirm your
selection.
If you have adjusted the temperature,
wait for approx. 6 hours if the
appliance is not very full and for
approx. 24 hours if the appliance is
full before checking the temperature
display, as it will take this long for the
appliance to give an accurate reading.
If, after this time, the temperature is
still too high or too low, you will need
to adjust it again.
Temperature range
The temperature can be adjusted:
– in the refrigerator section from 3°C to
9°C
– in the freezer section from -15°C to
-26°C.
29
The correct temperature
Adjusting the temperature in
the PerfectFresh Pro zone
In the PerfectFresh Pro zone, the
temperature is automatically maintained
between 0and 3°C. However, if you
would like it to be warmer or colder, e.g.
when storing fish, you can adjust the
temperature slightly.
The standard setting for the
temperature in the PerfectFresh Pro
zone is5. Under certain
circumstances, a setting from 1 to4
can cause negative temperatures to
be reached. Food could freeze.
Select a higher level.
Touch the settings button.
You can now adjust the temperature
in the PerfectFresh Pro zone by
touching the or button. You can
choose from settings 1 to 9:
1: lowest temperature,
9: highest temperature.
Touch the OK button to confirm your
selection.
The selected setting is applied, the
symbol flashes.
All symbols available for selection will
appear in the display and the symbol
flashes.
Touch the buttons for setting the
temperature ( or ) repeatedly until
the symbol flashes.
Touch the OK button to confirm your
selection.
The last selected setting flashes and
the symbol lights up in the display.
30
Touch the settings button to leave
settings mode.
Otherwise, the appliance electronics
will exit the settings mode
automatically after approximately one
minute.
The newly set temperature for the
PerfectFresh Pro zone will be reached
gradually.
Loading...
+ 86 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.