Operating and installation instructions
Fridge-freezer combination
To prevent the risk of accidents or damage to the appliance, it is
essential to read these instructions before it is installed and used for the
first time.
M.-Nr. 09 761 090en - AU, NZ
Contents
Description of the appliance.........................................5
Caring for the environment..........................................7
Warning and Safety instructions .....................................8
How to save energy ...............................................17
Switching on and off ..............................................19
Switching the appliance on ..........................................19
in the refrigerator or freezer zone
(X for colder; Y for warmer)
g Sensors for selecting the humidity in
the MasterFresh drawers
(left: high humidity;
right: low humidity)
h On/Off sensor for the SuperCool and
SuperFreeze functions
i On/Off sensor for the ice cube maker
(only visible if the freezer zone has
been selected)
j Sensor for switching off the
temperature or door alarm (only
visible when the temperature or door
alarm is sounding)
k Reminder to change the water filter
5
Description of the appliance
a Butter and cheese compartment
b Adjustable shelf
c Door shelf
d Floating deli drawer
e Control panel
f Humidity filters for the MasterFresh
zones
6
g Rocker switch for switching the
whole appliance on and off
h MasterFresh zones
i Ice cube maker
j Water filter
k Small freezer basket
l Large freezer basket
m Ice cube container
Caring for the environment
Disposal of the packing
material
The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation.
Rather than just throwing these
materials away, please ensure they are
offered for recycling.
Disposing of your old
appliance
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly,
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of it
with your household waste.
Please dispose of it at your local
community waste collection / recycling
centre and ensure that it presents no
danger to children while being stored
for disposal.
The plug must be rendered useless
and the cable cut off directly behind the
appliance to prevent misuse. Take care
not to damage the pipework at the back
of it before or during transportation to
an authorised collection depot.
In this way, refrigerant in the pipework
and oil in the compressor will be
contained, and will not leak out into the
environment.
7
Warning and Safety instructions
This appliance complies with all relevant local and national safety
requirements. Improper use of the appliance can, however,
present a risk of both personal injury and material damage.
To avoid the risk of accidents and damage to the appliance,
please read these instructions carefully before installation and
before using it for the first time. They contain important notes on
the installation, safety, operation and care of the appliance. Miele
cannot be held liable for damage caused by non-compliance with
these Warning and Safety instructions.
Keep these instructions in a safe place and pass them on to any
future owner.
,Danger of injury!
This appliance is very heavy and can tip forwards when the door
is open. Keep the appliance door shut until the appliance has
been built in and secured in its housing in accordance with these
operating and installation instructions.
Correct application
This appliance is designed for domestic use and for use in similar
~
environments by guests in hotel or motel rooms, bed & breakfasts
and other typical living quarters. This does not include
common/shared facilities or commercial facilities within hotels,
motels or bed & breakfasts.
This appliance is not suitable for outdoor use.
8
Warning and Safety instructions
This appliance is intended only for the cool storage of food and
~
drink as well as for storing deep frozen food, freezing fresh food and
for preparing ice.
Any other usage is at the owner's risk and could be dangerous.
This appliance is not suitable for storing and refrigerating
~
medications, blood plasma, laboratory preparations or similar
substances or products. Incorrect use of the appliance may result in
damage to or spoiling of the food or drinks being stored.
Furthermore, the appliance must not be operated in areas where
explosions may occur.
Miele cannot be held liable for damage resulting from improper or
incorrect use of the appliance.
This appliance is not intended for use by persons (including
~
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning its use by a person
responsible for their safety, and are able to recognise the dangers of
misuse.
Safety with children
Young children must not be allowed to use this appliance.
~
Older children may only use the appliance when its operation has
~
been clearly explained to them and they are able to use it safely,
recognising the dangers of misuse.
Cleaning work may only be carried out by older children under
~
the supervision of an adult.
9
Warning and Safety instructions
Children should be supervised when they are near the appliance.
~
This appliance is not a toy! To avoid the risk of injury, do not allow
children to play with it or to use the controls. They will not
understand the potential dangers posed by it. They should be
supervised whenever you are working in the kitchen.
The door hinges can cause injury. Keep children well away at all
~
times.
Please bear in mind that by removing the dividing panel in the
~
large freezer basket, children may be tempted to climb inside. THIS
COULD PUT THEIR LIVES IN DANGER.
Danger of suffocation! Children may be able to wrap themselves
~
in packing material or pull it over their heads with the risk of
suffocation. Keep children away from any packing material.
Technical safety
The refrigerant circuit has been checked for leaks. This appliance
~
complies with all current local and national safety requirements.
This appliance contains the coolant Isobutane (R600a), a natural
~
gas which is environmentally friendly. Although it is flammable, it
does not damage the ozone layer and does not increase the
greenhouse effect.
The use of this coolant has, however, led to a slight increase in the
noise level of the appliance. In addition to the noise of the
compressor, you might be able to hear the coolant flowing around
the system. This is unavoidable, and does not have any adverse
effect on the performance of the appliance.
Care must be taken during the transportation and setting up of the
appliance that no parts of the cooling system are damaged. Leaking
refrigerant can damage the eyes.
In the event of any damage:
–
avoid any flames or anything which creates a spark,
10
Warning and Safety instructions
switch off at the mains and unplug the appliance,
–
ventilate the room where the appliance is located for several
–
minutes, and
call Miele.
–
The more coolant there is in an appliance, the larger the room it
~
should be installed in. In the event of a leakage, if the appliance is in
a small room, there is the danger of combustible gases building up.
For every8gofcoolant at least 1 m
amount of coolant in the appliance is stated on the data plate inside
the appliance.
Before connecting the appliance, make sure that the connection
~
data on the data plate (fuse rating, voltage and rated load) matches
the mains electricity supply. This data must correspond in order to
avoid the risk of damage to the appliance.
Consult a qualified electrician if in any doubt.
The electrical safety of this appliance can only be guaranteed
~
when continuity is complete between it and an effective earthing
system which complies with local and national safety regulations. It
is most important that this basic safety requirement is present and
tested regularly and, where there is any doubt, the household wiring
system should be inspected by a qualified electrician.
3
of room space is required. The
If the connection cable is faulty, it must only be replaced by a
~
Miele approved service technician to protect the user from danger.
Do not connect the appliance to the mains electricity supply by a
~
multi-socket unit or an extension lead. These do not guarantee the
required safety of the appliance (e.g. danger of overheating).
11
Warning and Safety instructions
If moisture gets into electrical components, it could cause a short
~
circuit.
Therefore, do not operate this appliance in areas which are exposed
to moisture.
This appliance must not be installed and operated in mobile
~
installations (e.g. on a ship).
A damaged appliance is dangerous. Check the appliance for any
~
visible damage. Never install or attempt to use a damaged
appliance.
For safety reasons, this appliance may only be used when it has
~
been fully installed.
During installation, maintenance and repair work, the appliance
~
must be disconnected from the mains electricity supply. It is only
completely isolated from the electricity supply when:
– the mains fuse has been disconnected, or
– the screw-out fuse is removed (in countries where this is
applicable), or
– it is switched off at the wall socket and the plug is withdrawn from
the socket, or it is switched off at the isolator.
Repairs and installation work by unqualified persons could be
~
dangerous. The manufacturer cannot be held liable for unauthorised
work. Installation, maintenance work and repairs to electrical
appliances must only be carried out by a Miele approved service
technician.
The manufacturer's warranty will be invalidated if the appliance is
~
not repaired by a Miele approved service technician.
12
Warning and Safety instructions
Faulty components must only be replaced by genuine Miele
~
spare parts. The manufacturer can only guarantee the safety of the
appliance when Miele replacement parts are used.
Miele cannot be held liable for damage caused by a faulty
~
connection to the mains water supply.
Connection to the mains water supply and any repairs to the ice
~
cube maker must only be carried out by a Miele approved
technician.
The ice cube maker is not suitable for connection to a hot water
~
supply.
Connect the appliance to a potable water supply only.
~
Before plumbing the appliance in, ensure that it is disconnected
~
from the mains electricity supply.
Never tamper with the movable components on the ice cube
~
maker or the element on the ice cube maker. Danger of injury!
Correct use
The appliance is designed for use within a certain climate range
~
(ambient temperatures), and should not be used outside this range.
The climate range of the appliance is stated on the data plate inside
the appliance. Installing the appliance in a room with too low an
ambient temperature, e.g. a garage, can lead to the appliance
switching off for longer periods so that it cannot maintain the
required temperature.
To ensure proper air flow in and out of the appliance, the air vents
~
must not be covered or blocked in any way.
It would also increase the energy consumption and could cause
damage to the appliance.
13
Warning and Safety instructions
Make sure that any oil, or foods containing oil, do not come into
~
contact with plastic components as this could cause stress cracks.
Do not store explosive materials in the appliance or any products
~
containing propellants (e.g. spray cans). Flammable gas mixtures
can be ignited by electrical components.
Danger of fire and explosion!
Do not operate any electrical equipment (e.g. an electric ice
~
cream maker) inside the appliance. Danger of sparking and
explosion!
Do not store cans or bottles containing carbonated drinks or
~
liquids which could freeze in the freezer. The cans or bottles could
explode causing injury and damage.
If storing alcohol with a high percentage proof, make sure it is
~
tightly closed and stored upright in the refrigerator section. Danger
of explosion!
When cooling drinks quickly in the freezer, make sure bottles are
~
not left in for more than one hour; otherwise they could burst,
causing injury and damage.
Never handle frozen food or the metal parts of the appliance with
~
wet hands. Your hands may freeze to the frozen food or to the metal.
Danger of injury!
Do not take ice cubes out with your bare hands and never place
~
ice cubes or ice lollies in your mouth straight from the freezer. The
very low temperature of the frozen ice or lollies can cause frost burn
to the lips and tongue. Danger of injury!
14
Warning and Safety instructions
Do not refreeze food once it has thawed. Defrosted food should
~
be used up as quickly as possible as food soon loses its nutritional
value and goes off. Defrosted food may only be refrozen after it has
been cooked.
Food stored for too long may present a risk of food poisoning.
~
Storage times will depend on several factors, including the
freshness and quality of the food, as well as the temperature at
which it is stored. Follow the instructions given on the food
manufacturer's packaging regarding storage conditions and "use
by" dates.
To avoid the risk of any potential illness, do not deactivate the
~
reminder to change the water filter.
Use only Miele Original spare parts. If spare parts or accessories
~
from other manufacturers are used, the warranty will be invalidated,
and Miele cannot accept liability.
Cleaning and care
Do not use any oils or grease on the door seal, as these will
~
cause the seal to deteriorate and become porous with time.
Do not use a steam-cleaning appliance to clean this appliance.
~
Pressurised steam could reach the electrical components and
cause a short circuit.
Do not use sharp edged objects to
~
–
remove frost and ice,
–
separate frozen foods and remove ice trays.
They will damage the evaporator, causing irreversible damage to
the appliance.
15
Warning and Safety instructions
Never place electric heaters or candles in the appliance to
~
defrost it. These can damage the plastic parts.
Do not use defrosting sprays or de-icers, as they might contain
~
substances which could damage the plastic parts or which could
cause a build-up of gases and pose a danger to health.
Disposal of your old appliance
Before disposing of an old appliance, first make the door lock
~
unusable.
This way you will prevent children from accidentally locking
themselves in and endangering their lives.
Be careful not to damage any part of the pipework whilst awaiting
~
disposal, e.g. by
– puncturing the refrigerant channels in the condenser,
– bending any pipework, or
– scratching the surface coating.
Splashes of refrigerant can harm the eyes.
16
How to save energy
Installation/Maintenance
Temperature
settings
Normal energy
consumption
In a ventilated room.In an enclosed,
Protected from direct
sunlight.
Not situated near a heat
source (radiator, oven).
Where the ideal room
temperature is approx. 20 °C.
Where the cross-section of
the air inlet and outlet is not
covered and kept free of
dust.
Refrigerator section 4 to 5 °C With a low temperature
MasterFresh zones 1.5 °C
Freezer section -18 °C
Increased energy
consumption
unventilated room.
In direct sunlight.
Situated near a heat source
(radiator, oven).
Where there is a high room
temperature.
Where the air inlets and
outlets are covered or dusty.
setting: The lower the
temperature in the
appliance, the higher the
energy consumption.
17
How to save energy
Normal energy
consumption
UseDo not change the
arrangement of the drawers
and shelves as when
delivered.
Only open the door when
necessary and for as short a
time as possible.
Store food in an organised
way.
Take a cooler bag when
shopping and load food in the
appliance as quickly as
possible on your return home.
When food is taken out of the
refrigerator, be sure to put it
back before it becomes warm.
Allow hot food and drinks to
cool down before placing
them in the appliance.
Increased energy
consumption
Frequent opening of the door
for long periods will cause a
loss of coldness. The
appliance will try to cool down
and the running time of the
compressor will increase.
Warm food and food brought
in from room temperature add
heat to the appliance.
The appliance will try to cool
down and the running time of
the compressor will increase.
18
Store food covered or
packaged.
Place frozen food in the
refrigerator to defrost.
Do not overfill the appliance in
order to allow air to circulate.
The evaporation or
condensation of liquids will
cause a loss of coldness in the
refrigerator.
Before using for the first time
Clean the inside of the appliance and
^
the accessories with lukewarm water
and a little washing-up liquid, and
then dry with a soft cloth.
Important: To ensure the correct
functioning of the appliance, and
especially if it has been transported
horizontally, let it stand for 8 hours
after transporting it to its final
location before connecting it to the
mains.
Switching on and off
To enable the temperature to get
sufficiently cold inside the
appliance, allow the appliance to
run for a few hours before placing
food in it.
Do not place food in the freezer
section until the temperature is at
least -18° C.
Please note: switching off with the
rocker switch does not disconnect
the appliance from the mains.
Switching the appliance on
^ Open the upper appliance door.
^ Press the rocker switch.
This switch is located on the right-hand
side underneath the control panel.
This switches all of the zones in the
appliance on or off together.
The appliance will start to cool, and the
interior lighting will come on when the
door is opened.
The access sensor in the control panel
will also light up.
Operation
A light touch of the finger on the
sensors is all that is required to operate
this appliance.
Please note:
–Aselectable sensor is always
highlighted in white.
–Aselected sensor is always
highlighted in yellow.
^
Touch the access sensor so that it is
highlighted in yellow.
The sensors for the four zones in the
appliance will now appear in the control
panel: Refrigerator section, left and
right-hand MasterFresh zones and the
freezer section.
19
Switching on and off
The On/Off sensor for the ice cube
maker appears on the right-hand side
of the control panel (only visible if the
freezer zone has been selected).
If the ice cube maker is in operation,
the sensor is highlighted in yellow.
To select settings for your appliance
(e.g. to set the temperature, etc.),
^ touch the sensor for the particular
zone of the appliance where you
would like to select the settings.
The applicable sensor will then be
highlighted in yellow, and depending
on the zone, further settings which may
be selected will now appear in the
display.
To switch off a section again,
touch the sensor of the selected zone
^
again so that it is highlighted in white,
or select a different sensor.
To leave settings mode,
touch the access sensor so that it is
^
highlighted in white.
Your last selected settings will now be
saved to memory.
If you do not touch the access sensor,
the electronics for accessing the
settings will switch off after a period.
Switching off
Depending on which zone you have
selected, you can
–
adjust the temperature,
–
select the Supercool/SuperFreeze
functions,
–
select the humidity level in the
MasterFresh zones,
–
switch on the ice cube maker.
Please refer to the relevant section for
more information.
20
^
Press the rocker switch.
The cooling system and the lighting are
now switched off.
Switching on and off
Further settings
Further settings can be selected in the
settings mode.
In settings mode, you can select certain
appliance functions via the control
panel and adjust the settings. The
settings for the different functions are
described in more detail in the relevant
section of these instructions.
Overview of functions that can be
selected in the settings mode:
FunctionSymbol
displaye
d
To enter or leave
settings mode
To select the
temperature unit (see "The
correct temperature")
No function selected;
To switch the sensor tone
on/off (see "Switching on
and off")
No function selected^
;
†
=
To switch the sensor tone on/off
The tone which sounds each time a
sensor is touched can be deactivated.
Touch the access sensor so that it is
^
highlighted in yellow.
^ Touch the sensor for the refrigerator
zone so that it is highlighted in
yellow.
^ Take note of the position of the X
sensor (but do not touch it!).
^ Touch the access sensor until it is
highlighted in white and all of the
other sensors are no longer lit up.
^ Place your finger in the position of the
X sensor, and leave it there.
^
At the same time, briefly touch the
access sensor (without letting go of
the X sensor).
21
Switching on and off
Leave your finger on the X sensor for
^
another 4 seconds until c and the Y
sensor also appear in the display.
Now touch the X sensor repeatedly
^
until b appears in the display.
Touch the access sensor again.
^
By touching the X sensor, you can
^
now select whether the sensor tone is
switched on or off:
= 0: Sensor tone switched off
= 1: Sensor tone switched on
= –: Return to menu
^ After selecting a new setting, touch
the access sensor to confirm your
choice.
^ Touch the X sensor repeatedly until ;
appears in the display.
^
Touch the access sensor.
You have now left settings mode.
Switching off for longer
periods of time
If the appliance is not going to be used
for a longer period of time, e.g. whilst
on holiday:
switch the appliance off,
^
switch off at the wall and withdraw
^
the plug from the socket, or
disconnect the mains fuse or remove
the screw-out fuse in countries where
this is applicable,
turn off the tap to the water supply (a
^
few hours before you switch off the
appliance),
^ empty the ice cube container,
^ clean the appliance out,
^ replace the water filter and
^ leave the door ajar to air the
appliance.
If, during a long absence, the
appliance is switched off but not
cleaned out and the doors are left
shut, there is a danger of mould and
odours building up inside the
appliance.
The door alarm is automatically
disabled when the appliance is in
settings mode. As soon as the door
is closed, the door alarm is
activated again.
22
The correct temperature
It is very important to set the correct
temperature for storing food in the
appliance. Micro-organisms will cause
food which is not stored at the correct
temperature to deteriorate rapidly.
Temperature influences the growth rate
of these micro-organisms. Reducing
the temperature reduces their growth
rate.
The temperature in the appliance will
rise:
the more often the door is opened
–
and the longer it is kept open,
– the more food that is stored in it,
– the warmer the food is which is being
put into it,
– the higher the ambient temperature
surrounding the appliance.
The appliance is designed for use in
specific ambient temperatures
(climate ranges). Do not use in
ambient temperatures for which it is
not designed.
DynamicCooling
The DynamicCooling fan automatically
switches on when the cooling system
for the refrigerator switches on. It
distributes the temperature in the
appliance to all areas more evenly so
that all the food will be chilled to about
the same degree.
...inthefreezer
To freeze fresh food and to store frozen
food for a long time, a temperature of
-18 °C is required. At this temperature
the growth of micro-organisms is
generally halted. As soon as the
temperature rises above -10 °C, the
micro-organisms become active in the
food again so that it cannot be kept as
long. For this reason, partially defrosted
or defrosted food must not be re-frozen.
Food may be re-frozen once it has
been cooked, as the high temperatures
achieved when cooking destroy most
micro-organisms.
...intherefrigerator and the
MasterFresh zone
We recommend a temperature of 4°C
in the refrigerator.
The temperature in the MasterFresh
zone is controlled automatically and is
maintained at 1.5 °C.
23
The correct temperature
Setting the temperature in the
refrigerator/freezer zones
The temperatures in the refrigerator and
freezer zones are set independently of
one another.
Touch the access sensor so that it is
^
highlighted in yellow.
^ Touch the sensor for the refrigerator
or freezer zone so that it is
highlighted in yellow.
^ The temperature inside the appliance
can be selected by touching the
arrow sensors on either side of the
temperature display.
By touching the
X sensor:the temperature will get
colder
Y sensor:the temperature will get
warmer.
The temperature range being set will
flash in the display as you do this.
If the highest or lowest temperature that
it is possible to set is reached, the X or
Y sensor will disappear from the
display.
The temperature display on the
control panel always shows the
selected temperature.
When you have adjusted the
temperature, wait for approx. 6 hours
if the appliance is not very full and
for approx. 24 hours if the appliance
is full before checking the temperature,
as it will take this long for the appliance
to reach the temperature. If, after this
time, the temperature is still too high or
too low, you will need to adjust it again.
Temperature range
The temperature can be adjusted:
– In the refrigerator section from 2 °C
to8°C
–
In the freezer section from -14 °C to
-24 °C.
The ambient temperature in the
room and the installation location
can affect the time it takes for the
appliance to reach the lowest
temperature. If the ambient
temperature is too high, the
appliance may not reach the lowest
temperature.
–
Touching the sensor once:
adjusts the temperature shown in
1 °C steps.
–
Keeping your finger on the sensor:
changes the temperature
continuously.
24
Temperature
(Fahrenheit/Celsius)
The temperature can be displayed in
degrees Celsius or degrees Fahrenheit.
Touch the access sensor so that it is
^
highlighted in yellow.
^ Touch the sensor for the refrigerator
zone so that it is highlighted in
yellow.
^ Take note of the position of the X
sensor (but do not touch it!).
^ Touch the access sensor until it is
highlighted in white and all of the
other sensors are no longer lit up.
^
Place your finger in the position of the
X sensor, and leave it there.
The correct temperature
Now touch the X sensor repeatedly
^
until † appears in the display.
Touch the access sensor again.
^
By touching the X sensor, you can
^
now set the temperature to be
displayed in Fahrenheit or Celsius.
†0: Temperature in Fahrenheit
†1: Temperature in Celsius
† –: Return to menu.
^ After selecting a new setting, touch
the access sensor to confirm your
choice.
^ Now touch the X sensor repeatedly
until c appears in the display.
^ Touch the access sensor again.
You have now left settings mode.
^
At the same time, briefly touch the
access sensor (without letting go of
the X sensor).
^
Leave your finger on the X sensor for
another 4 seconds until c and the Y
sensor also appear in the display.
The door alarm is automatically
disabled when the appliance is in
settings mode. As soon as the door
is closed, the door alarm is
activated again.
25
The correct temperature
Temperature display
The temperature display on the
control panel always shows the
selected temperature.
The temperature displays flash if
a different temperature is being set,
–
the temperature in the appliance has
–
risen by several degrees, indicating
that the appliance is warming up too
much.
This loss of coldness is no cause for
concern in the following circumstances:
– when the door has been left open for
a while, e.g. for removing or storing a
large amount of food,
– when fresh food is being frozen.
However, if the temperature in the
freezer section remains above -18°C
for a long time, check that the frozen
food has not started to defrost. If it
has, check that the food is safe to
use and if it is, then use it as soon
as possible.
26
Alarm
Your appliance has been fitted with a
warning system which ensures that the
temperature in the appliance cannot
rise unnoticed and to avoid energy
being wasted if a door is left open.
Activating the alarm system
The alarm system is always active. It
does not have to be switched on
manually.
Temperature alarm
If the temperature in one of the zones
gets too warm, the sensor for the zone
concerned will flash in the control
panel.
The Alarm off sensor will flash at the
same time.
An audible alarm will also sound.
If the temperature rises in the freezer,
the temperature display will show the
highest temperature that was reached
during the time the temperature in the
freezer rose.
The alarm will sound and the relevant
symbol will flash, for example,
–
if the freezer door has been left open
for a while, e.g. in order to load,
re-arrange or take food out.
The alarm will stop and the Alarm off
sensor in the display will go out again
as soon as the temperature has
dropped down to the correct level
again. The sensor for the zone
concerned will constantly light up.
Switching the temperature
alarm off early
If the noise disturbs you, you can
switch the alarm off early if you wish.
^ Touch the Alarm off sensor.
The alarm will stop.
The Alarm off sensor will continue to
be lit up until the temperature has
dropped down to the correct level
again.
However, if the temperature in the
freezer section remains above
-18 °C for a long time, check that the
frozen food has not started to
defrost. If it has, check that the food
is safe to use and if it is, then use it
as soon as possible.
–
when freezing large amounts of food
at once.
–
in the event of a power cut.
27
Alarm
Door alarm
The alarm will sound if a door is left
open for more than 5 minutes. The
Alarm off button will also light up.
The alarm will stop and the Alarm off
sensor in the display will go out as soon
as the door has been shut.
Switching the door alarm off
early
If the noise disturbs you, you can
switch the alarm off early if you wish.
^ Touch the Alarm off sensor.
The Alarm off sensor in the display
will go out and the alarm will stop.
28
SuperCool and SuperFreeze
SuperCool
The SuperCool function can be used to
rapidly reduce the temperature in the
refrigerator to its lowest setting
(depending on the room temperature).
Switching on SuperCool
SuperCool is particularly recommended
for the faster chilling of large amounts
of fresh food or drink.
^ Touch the sensor for the refrigerator
zone so that it is highlighted in
yellow.
^ Touch the SuperCool sensor so that it
lights up in yellow.
Switching off SuperCool
The SuperCool function will switch itself
off automatically after approx. 6 hours.
The sensor is highlighted in white and
the appliance continues running at
normal power.
To save energy, the SuperCool function
can be switched off once food and
drinks are sufficiently chilled.
^ Touch the SuperCool sensor so that it
is highlighted in white.
The original temperature will now
appear in the temperature display for
the refrigerator, and the appliance will
continue to operate at normal power.
The appliance will now operate at full
power to lower the temperature in the
refrigerator zone, and the newly set
temperature of 2°C will show in the
temperature display.
29
Loading...
+ 67 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.