Miele HR1421, HR1622, HR1124, HR1134, HR1135 Operating instructions
...
Installation Instructions
30" Electric, 30" Induction Range
30", 36" All Gas Range
30", 36", 48" Dual Fuel Range
To prevent accidents and damage to the range, you must read all
instructions supplied before installing or using the appliance.
en-US, CA M.-Nr. 10 876 460
IMPORTANT SAFETY INSTRUCTIONS
All ranges can tip
Injury to persons
could result
Install anti-tip devices
packed with range
See installation
instructions
WARNING
WARNING
Children and adults can tip over the range if has not been secured.
This may lead to fatal injuries.
This range must be secured and connected using the anti-tip
device according to the installation instructions.
If you have moved the range, slide the locking latch onto the anti-
tip device until you feel it lock into place.
Do not use the range if the anti-tip device has not been properly
installed and engaged.
Failure to observe the information contained in the installation
instructions can lead to serious or fatal injuries for children and
adults.
2
IMPORTANT SAFETY INSTRUCTIONS
®
®
WARNING: If the information in this manual is not followed exactly, a fire or
explosion may result causing property damage, personal injury, or death.
– Do not use or store gasoline or other combustible liquids or vapors in the vicinity
of this or any other appliance.
– WHAT TO DO IF YOU SMELL GAS
– Do not try to light any appliance.
– Do not touch any electric switches.
– Do not use any phones inside your building.
– Immediately call your gas supplier from a neighbor's phone. Follow the gas
supplier's instructions.
– If you are unable to reach your gas provider, call the fire department.
– Installation and service must be performed by a qualified installer, qualified
service agency or your gas provider.
(In Massachusetts, installation must be performed by a licensed installer / gas
fitter.)
– Note to the installer:
Please give these installation instructions to the consumer for the local
electrical/gas inspector.
3
Contents
IMPORTANT SAFETY INSTRUCTIONS ................................................................ 2
IMPORTANT SAFETY INSTRUCTIONS ................................................................ 7
Notes on installation ...........................................................................................15
Model numbers .................................................................................................... 15
Data plate ............................................................................................................. 15
Distance to the range hood................................................................................... 15
Items included with this range............................................................................... 15
Toe-kick and drip tray.......................................................................................16
Installation of the toe-kick ................................................................................ 16
Installation of the drip tray................................................................................ 16
Assembling the grill .......................................................................................... 17
Optional accessories............................................................................................. 18
RBGAG All Gas Backguard/RBGDF Dual Fuel Backguard ..............................18
RBS Backsplash............................................................................................... 21
XKM3000W Remote Vision (USA Only).......................................................... 21
Required connections ........................................................................................... 23
All Electric Range dimensions ...........................................................................24
HR 1421; HR 1622 ................................................................................................ 24
Detailed views of HR 1421 .................................................................................... 26
Detailed views of HR 1622 .................................................................................... 30
All Gas Range dimensions.................................................................................. 34
All Gas Range HR 1124 with Standard Burner Configuration M Pro Power Plus . 34
All Gas Range HR 113x with Standard Burner Configuration M Pro Power Plus . 36
All Gas Range HR 113x with BTU reducing nozzle configuration (M Pro Power Zero
Gap Kit, M Pro - décor hood)................................................................................ 39
Detailed views of HR 1124 .................................................................................... 42
Detailed views of HR 1134 .................................................................................... 46
Detailed views of HR 1135 .................................................................................... 50
Detailed views of HR 1136 .................................................................................... 54
Dual Fuel Range dimensions.............................................................................. 58
Dual Fuel Range HR 1724 with Standard Burner Configuration M Pro Power Plus...
58
Dual Fuel Range HR 1924 with Standard Burner Configuration M Pro Power Plus...
60
Dual Fuel Range HR 193x/195x with Standard Burner Configuration M Pro Power
Plus........................................................................................................................ 62
Dual Fuel Range HR 193x with BTU reducing nozzle configuration (M Pro Power
Zero Gap Kit, M Pro - Décor Hood)....................................................................... 66
4
Contents
Dual Fuel Range HR 195x with BTU reducing nozzle configuration
M Pro Power Zero Gap Kit .................................................................................... 69
Detailed views of HR 1724 .................................................................................... 71
Detailed views of HR 1924 .................................................................................... 75
Detailed views of HR 1934 .................................................................................... 79
Detailed views of HR 1935 .................................................................................... 83
Detailed views of HR 1936 .................................................................................... 87
Detailed views of HR 1954 .................................................................................... 91
Detailed views of HR 1955 .................................................................................... 95
Detailed views of HR 1956 .................................................................................... 99
Anti-tip device.................................................................................................... 103
Before installation................................................................................................ 103
Checking the installation space .......................................................................... 104
Included accessories........................................................................................... 106
Installation dimensions of locking bolt ................................................................ 106
Installing the range with the anti-tip device......................................................... 106
Disconnecting the range from the anti-tip device ............................................... 110
Electrical connection ........................................................................................111
Data plate ....................................................................................................... 112
Plumbing ............................................................................................................113
Notes on connecting to the water supply ........................................................... 113
Attach the stainless steel hose to the range. ...................................................... 114
Connecting to the water supply .......................................................................... 114
Gas connection.................................................................................................. 115
Burner ratings of Standard Burner Configuration.......................................... 117
Burner ratings for HR 1124 ................................................................................. 117
Burner ratings for HR 1134 ................................................................................. 118
Burner ratings for HR 1135 ................................................................................. 119
Burner ratings for HR 1136 ................................................................................. 120
Burner ratings for HR 1724 ................................................................................. 121
Burner ratings for HR 1924 ................................................................................. 121
Burner ratings for HR 1934 ................................................................................. 121
Burner ratings for HR 1935 ................................................................................. 122
Burner ratings for HR 1936 ................................................................................. 122
Burner ratings for HR 1954 ................................................................................. 123
Burner ratings for HR 1955 ................................................................................. 123
Burner ratings for HR 1956 ................................................................................. 124
Burner ratings of M Pro Power (Zero Gap) .................................................... 125
5
Contents
Burner ratings of M Pro (Décor Hood) ............................................................ 126
Possible combinations - Range with BTU Reducing jet kit........................... 127
Caring for the environment .............................................................................. 128
6
IMPORTANT SAFETY INSTRUCTIONS
When using the appliance, follow basic safety precautions, including the
following:
Read all instructions before installation and use of the range to prevent
accidents and machine damage.
This range complies with current safety requirements. However,
improper use of the appliance can result in personal injury or
damage to property.
Please read the installation instructions carefully before installing
and connecting the appliance.
Read the operating instructions before using the range for the first
time. To prevent accidents and damage to the appliance, always
observe both the installation instructions and operating
instructions. Both documents contain important information about
installation, safety, use and maintenance.
Miele cannot be held liable for damage occurring as a result of
non-compliance with the instructions.
Keep these installation instructions and operating instructions in a
safe place and pass them on to any future owner.
7
IMPORTANT SAFETY INSTRUCTIONS
Use
This range is intended for domestic use and use in other similar
environments.
This appliance is not intended for outdoor use.
Use the range exclusively under normal domestic conditions:
– Use the oven for baking, roasting, broiling, defrosting, canning
and drying food.
– Use the stovetop to prepare food and keep it warm.
Any other use is not permitted.
Risk of Fire! Do not use this oven to store or dry combustible
materials.
Persons who lack physical, sensory or mental abilities, or
experience with the appliance should not use it without supervision
or instruction by a responsible person.
8
IMPORTANT SAFETY INSTRUCTIONS
Children
Children must be kept away from the range unless constantly
supervised.
Please supervise any children in the vicinity of the range and do
not let them play with the appliance.
Burn hazard from improper use! Do not allow children to operate
the oven.
Danger of suffocation! Ensure that any plastic wrappings, bags,
etc. are disposed of safely and kept out of the reach of children.
Burn hazard!
Keep the spaces above and behind the range clear of any items that
could draw the attention of children. Otherwise, they can be tempted
into climbing onto the appliance.
Danger of injury. Never allow children to hang or lean on any part
of the appliance.
9
IMPORTANT SAFETY INSTRUCTIONS
Technical safety
Installation, repair and maintenance work should be performed by
a Miele authorized service technician in accordance with national
and local safety regulations and the provided installation
instructions. Contact Miele’s Technical Service Department for
examination, repair or adjustment. Repairs and other work by
unauthorized persons could be dangerous and may void the
warranty.
Do not carry or lift the range by the oven door handle or the
control panel!
Check whether the anti-tip device is properly installed and locked
into place (see"Anti-tip device"):
– The anti-tip device must be fastened to the floor or wall with
suitable screws.
– You must be able to feel that the locking latch is engaged in the
bolt of the anti-tip device.
Slide the range's locking latch into place on the anti-tip device.
The locking latch must be noticeably engaged with the bolt of the
anti-tip bracket.
A damaged range can be dangerous. Always check for visible
signs of damage. Never use a damaged appliance.
Reliable and safe operation of the range can only be guaranteed if
it is connected to the public power supply.
The electrical safety of the range can only be guaranteed when it
is properly grounded. Compliance with this essential safety
requirement is absolutely mandatory. If in any doubt, please have the
building's wiring system inspected by a qualified electrician.
To avoid damaging the range, make sure that the connection data
(voltage and frequency) on the data plate correspond to the
building's power supply before connecting the appliance.
When in doubt, consult a qualified electrician.
10
IMPORTANT SAFETY INSTRUCTIONS
During installation, maintenance and repair work, e.g. if the oven
lighting is broken, the range must be completely disconnected from
the household electricity supply (see"Frequently asked questions").
The gas inlet valve must be closed. It is only completely isolated
from the supply when:
– The circuit breakers have been switched off, or
– the fuses of the electrical installation have been completely
removed, or
– the plug (if present) is removed from the socket. To do this, pull
the plug not the cord.
– Shut off the gas supply and disconnect the range from the gas
supply. Installation and maintenance of the gas connection must
be performed by qualified installers, service agencies or gas
providers.
Do not use a power strip or extension cord to connect the range
to electricity. These are a fire hazard and do not guarantee the
required level of appliance safety.
Any contact with live connections or tampering with the electrical
or mechanical components of the range will endanger your safety
and may lead to appliance malfunctions.
Do not open the appliance housing under any circumstances.
11
IMPORTANT SAFETY INSTRUCTIONS
This appliance must not be installed and operated in mobile
installations (e.g. on a ship).
Any repairs not performed by a Miele authorized service
technician will void the warranty.
Defective components should be replaced by Miele original parts
only. Only with these parts can the manufacturer guarantee the
safety of the appliance.
Risk of electric shock! If the ceramic surface of the stovetop is
defective or chipped, cracked or broken in any way, immediately
switch the stovetop off and do not continue to use it. Disconnect the
range from the power supply and contact Miele Technical Service.
In order for the range to function properly, it requires an adequate
supply of cool air. Ensure that the air flow is not impaired. Also be
sure that the cool air supply is not excessively heated by other heat
sources (e.g. solid fuel stoves).
If the range is installed behind a cabinet door, do not close the
door while the appliance is in operation. Heat and moisture can build
up behind the closed door and cause damage to the range and to
the surrounding cabinets and flooring. Do not close the door until the
appliance has completely cooled down.
Reaching over a hot cooktop to access the cabinets can result in
burns. You can reduce the risk of burns by installing a range hood
that extends at least 4 3/4" (12 cm) past the bottom of the cabinets.
12
IMPORTANT SAFETY INSTRUCTIONS
The water shutoff valve must be accessible after the range has
been installed.
The integrated Waterproof System offers protection against water
damage if the following conditions are met:
– The range is properly installed (connected to electric and water
supply).
– The range is repaired immediately whenever damage is detected.
– The water supply is shut off during extended periods of non-use
(e.g. vacation).
Hard water, water containing minerals and water from reverse
osmosis filtering systems can damage the range. Only use filtered,
softened and demineralized water from the building's plumbing to
supply the range.
Preparing your appliance for an extended vacation
If you elect to turn off the water to your home for an extended
period of time, please note that this may not be enough to reduce
the risk of a leak. To be completely safe, you must turn off the water
supply to each individual appliance.
13
IMPORTANT SAFETY INSTRUCTIONS
Cleaning and care
The steam from a steam cleaning appliance could reach live
electrical components and cause a short circuit.
Do not use a steam cleaner to clean the range.
Only clean parts listed in these Operating and Installation
Instructions.
Scratches on the door glass can cause the glass to break.
Do not use abrasive cleaners, hard sponges, brushes or sharp metal
tools to clean the door glass.
The shelf runners can be removed for cleaning purposes (see
"Cleaning and care"). Ensure they are correctly fitted after cleaning
and never operate the oven without the shelf runners inserted.
There is a seal around the oven interior which seals the inside of
the door. Take care not to rub, damage or move the gasket.
Do not use oven cleaners. Commercial oven cleaners or oven
liners of any kind should not be used in or around any part of the
oven.
Debris should be removed before running the Self Clean program.
If not removed this debris can smoke causing the self-cleaning
program to turn itself off.
SAVE THESE INSTRUCTIONS AND REVIEW THEM PERIODICALLY
14
Notes on installation
Model numbers
A list of the ovens described in these
operating instructions can be found on
the back page.
Data plate
The data plate is behind the toe-kick.
The toe-kick cover is attached to the
base of the range by magnets so it can
be removed and put back again easily.
There you can find the model number,
the serial number and the connection
data (voltage/frequency/maximum rated
load) for your range.
Have this information available when
contacting Miele Technical Service.
Distance to the range hood
The minimum clearance between the
appliance and a range hood above will
be listed by the hood manufacturer.
If there is more than one appliance
installed below the range hood, each
with a different safety clearance, the
largest clearance must be used.
Items included with this range
The range is supplied with:
– Installation Instructions,
– Multiple operating instructions
(depending on model) for:
– Electric Range
– Induction Range
– Convection Oven
– Gas Cooktop
– Gas Convection Oven
– Speed Oven
– Warming Drawer
– an anti-tip device including screws
for fastening the range,
– various accessories.
15
Notes on installation
Toe-kick and drip tray
30" and 36" range
The components are located in the
packaging of the range.
48" range
The components are already installed.
Installation of the toe-kick
The toe-kick has sheet metal lugs and
magnets by means of which it can be
positioned and attached to the base of
the range.
Position the toe-kick in such a way
that the sheet metal lugs are facing
the provided holes in the base.
Push the toe-kick onto the base of
the range until it audibly locks into
place.
Installation of the drip tray
The drip tray covers the gap between
the oven cavity and the door.
Open the oven door.
Lay the drip tray over the gap
between the oven cavity and the
door.
Close the oven door.
16
Assembling the grill
Burn hazard!
The burners must be turned off and
allowed to cool completely.
Risk of injury!
The cast-iron grill is heavy.
Carry the grill carefully and place it
securely on a soft base so that it lies
flat.
Notes on installation
Place the grill into position.
Cleaning and care
Tip: All parts can be disassembled in
the reverse order. You can also remove
the frame for cleaning.
a
Grill
b
Radiant plate
c
Frame
Using a soft sponge, clean radiant
plate with a solution of warm water
and a small amount of liquid dish
soap. Dry the parts thoroughly after
cleaning.
Remove the grill from the gas
cooktop.
Place the radiant plate on top of
the frame .
17
Notes on installation
Optional accessories
All accessories and cleaning products
listed in these instructions are designed
to be used with the Miele range.
These can be ordered from the Miele
website (see end of this booklet for
contact details).
When ordering, please have your model
number available.
RBGAG All Gas Backguard/RBGDF Dual Fuel Backguard
Depending on the model, you can
exchange the existing island trim of
your appliance for a larger range
backguard. The backguard is available
in the following heights: 12" (305 mm)
and 20" (508 mm).
Installing the RBGDF Dual Fuel Backguard
The rear of the range must be
accessible.
Install the backguard before installing
the anti-tip device and connecting of
the range.
Loosen the screws of the island trim.
Pull back the island trim slightly until
it can be removed.
The backguard can be installed in
reverse order.
18
Mounting the RBGAG All Gas
1
22
1 2 3
Backguard
The rear of the range must be
accessible.
Mount the backguard before installing
the anti-tip device and connecting of
the range.
Loosen the screws of the island trim.
Pull back the island trim slightly until
it can be removed.
Notes on installation
a
Backguard
b
Rear panel backguard
c
Interior panel
To avoid scratching the backguard
, place it front side downwards on a
soft surface (e.g., a blanket). The
lower edge should line up with the
edge of the table so that the
backguard is lying flat.
Remove the screws from the rear of
the backguard.
Remove the rear and interior
panels.
a
Extender
b
Air ducts
Insert one extender onto each of
the left and right air ducts .
Screw the extenders into place with
2 screws each.
19
Notes on installation
1
2
a
Backguard
b
Range
Secure the interior panel and the rear
panel to the backguard with the
screws supplied.
Secure the backguard to the range
with the screws supplied.
Backguard 12"
Push the backguard over the air
duct extensions from above.
As soon as the backguard is sitting
on the range, push the backguard
backwards.
20
Backguard 20"
RBS Backsplash
The backsplash is intended for
installation to a Miele Range Hood (DAR
model). Observe the installation
instructions of the Miele Range Hood.
XKM3000W Remote Vision (USA
Only)
Depending on the model, the range
maybe compatible with
RemoteVisionTM.
In order to use the RemoteVision
TM
monitoring service, you will require a
XKM3000W Communication Module.
Refer to the Operating and Installation
Instructions of the Miele XKM3000W
Communication Module.
Notes on installation
21
Notes on installation
Do not carry or lift the range by the oven door handle or the control panel!
The range is heavy.
Due to the size and weight of the appliance, installation should be performed by
two people.
The net weight of the range with accessories is as follows:
Model Width Net weight incl.
accessories
HR 1421
HR 1622
HR 112x
HR 1724
HR 192x
HR 113x
HR 193x
HR 195x 4715/16"
Installation location
This appliance is not intended for outdoor use.
Ranges with a connection to the water supply should not be installed in rooms
where there is a risk of freezing temperatures.
The floor of the space where the appliance is to be installed must be flat, level and
made of a strong, rigid material.
The niche floor must be made of strong, rigid material.
Because the Range is heavy and has to be secured with the anti-tip device
supplied, the surface must be able to fully bear the load of the appliance. If
necessary, seek the advice of an architect or construction expert.
2915/16"
(762mm)
3515/16"
(915mm)
(1220mm)
approx. 307 lbs (140 kg)
approx. 405 lbs (180 kg)
approx. 573 lbs (260 kg)
Ventilation
The air intake and outlet openings must not be covered or blocked in any way.
22
Required connections
Notes on installation
Model Electrical
connection
HR 1421 X – –
HR 1622 X – X
HR 112x
HR 113x
HR 1724 X X –
HR 192x
HR 193x
HR 195x
X Connection required
– Connection not provided
X X –
X X X
Gas connection Plumbed-water
connection
23
All Electric Range dimensions
2
HR 1421; HR 1622
, , The shaded area represents the installation area for the connections:
E = Electrical connection,
W = Water connection (only HR 1622)
24
All Electric Range dimensions
HR 1421; HR 1622
Position Dimensions Description
13" (330mm) Maximum depth of top cabinet
18" (547mm) Minimum distance to bottom edge of top
cabinet
35 1/2"–37"
(901–940 mm)
min. 30"
(762mm)
30" (762mm) Minimum distance between the top of the
or 24" (609mm) Minimum distance to a protected combustible
For all other hoods please consult the manufacturer's specifications
for required distances.
Please observe safe distances to rear combustible surfaces of 12" (305mm) clearance. For
zero clearance installation the Miele Backguards will satisfy the required distance to
combustible surfaces. The Miele Backguard is available in 12" (305mm) or 20" (508mm)
heights.
approx.
101/16" (256 mm)
approx.
4
1/2" (115mm)
approx.
2
13/16" (72mm)
Distance from the floor to cooktop surface
Niche width
cooking area and the bottom of an unprotected
combustible surface.
surface or when a Miele Ventilation Hood is
installed.
Maximum connection width right
and left
Maximum connection height
Maximum connection depth
Position of
the wall
socket
25
All Electric Range dimensions
Detailed views of HR 1421
Side view of HR 1421
(x) = Depending on the appliance height adjustment
5" - 61/2" (127 mm - 165.1 mm)
26
Detailed front side view of HR 1421
All Electric Range dimensions
27
All Electric Range dimensions
Front side view of HR 1421
(x) = Depending on the appliance height adjustment
5" - 61/2" (127 mm - 165.1 mm)
28
Rear view of HR 1421
All Electric Range dimensions
E = Electrical connection
29
All Electric Range dimensions
Detailed views of HR 1622
Side view of HR 1622
(x) = Depending on the appliance height adjustment
5" - 6 1/2" (127 mm - 165.1 mm)
30
Loading...