Miele G 876 Operating Instruction

Operating Instructions
for Dishwashers G 676 / G 876
It is essential to read these operating instructions before installing or using the machine, to avoid the risk of accident or damage to the machine. M.-Nr. 04 936 890
Q
Contents
Contents
Guide to the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Warning and safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Caring for the environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Before using for the first time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Opening and closing the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Water softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setting the water hardness level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Filling the salt reservoir/salt indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13/14
Adding rinse aid/Rinse aid dosage setting . . . . . . . . . . . . . . . . . . . . . . . . . . 15/16
Loading the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Loading examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Cutlery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Flap-up racks, positioning rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Adjusting the upper basket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Items not suitable for dishwashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Adding detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Programme selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Switching on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Starting a programme, Programme sequence display, End of a programme . . . . 32
Programme interruption, Programme change . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Removing the load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Additional options / “Top Solo” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Checking the water level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Extended water inlet time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Dealing with minor faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Special accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Comparison tests. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Installation instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
2
Guide to the appliance
Miele dishwashers are available in three versions:
Guide to the appliance
1. “Freestanding” dishwashers
“Freestanding” dishwashers do not re­quire any special installation fixings in the kitchen, (except for plumbing). A decor frame can be added to take a panel for matching the dishwasher to the kitchen fronts, (with some models this is fitted as standard).
2. Integrated (“i”) dishwashers
“i” dishwashers are specially designed for building under a continuous work­top.
The control panel with its accessories is included with the “i” dishwasher in a separate package for on-site fixing. The front is designed to be fitted with a base unit “door” front to match the kit­chen furniture.
The dishwasher does not have a plinth facia. The plinth area can be covered either with facia to match your kitchen furniture if available, or another facia. The separate plinth facia can be fitted to match the height of adjacent plinths. The plinth return is freely adjustable.
3. “U” dishwashers
The built-under(“U”) dishwashers use the integrated (“i”) dishwashers as the basic machine.
By using a decor set (GDU) the “i”dish­washer can be converted into a “U” model dishwasher.
GDU installation instructions are in­cluded in a separate installation leaflet supplied with the decor set.
All notes on installation are described in the section on “Installation instructions”.
3
Guide to the appliance
View of the machine
Control panel (facia)
4
Guide to the appliance
1 Upper spray arm (not visible) 2 Cutlery tray
(standard depending on model)
3 Upper basket, (design varies
according to model, and may not match the one shown).
4 Water guide duct for the middle
spray arm 5 Middle spray arm 6 Water hardness selector 7 Lower spray arm 8 Four height-adjustable screw feet 9 Filter combination 10 Salt reservoir 11 Dual compartment detergent
dispenser 12 Rinse aid reservoir
(with dosage selector) 13 Data plate
There are various models for differ­ent countries. The model number of your dishwasher (e. g. G 676) is listed on the data plate (13).
Throughout this booklet the G 676 (SC) (i), (G 677 and G 678 SC(i)) will be referred to generally as G 6XX.
Similarly the G 876 SCi to G 878 SCi will be referred to as G 8XX.
See the Technical Data section for details of height and capacity.
14 ON / OFF button 15 Door opener 16 Child safety lock 17 Top Solo button 18 Indicator lights 19 Programme sequence display 20 Programme selector buttons
5
Warning and safety instructions
Warning and safety instructions
This appliance conforms to current safety requirements. Inappropriate use can however lead to personal injury and damage to property. Read the operating instructions carefully before starting to use this machine. This way you will avoid the risk of accidents, and damage to the machine. Keep these instruc­tions in a safe place for reference, and pass them on to any future user.
Appropriate usage
This dishwasher is intended exclu-
sively for cleaning domestic croc­kery and cutlery in a domestic house­hold. Do not use for purposes other than those for which it was designed. Any other applications may be dan­gerous. The manufacturer cannot be held re­sponsible for any damage caused by improper use or uses other than those for which the appliance is intended.
The following notes are to help avoid personal injury
To ensure stability integrated and
built-under models must be in­stalled under a continuous worktop which has been firmly screwed to neighbouring units.
not be held responsible for damage caused by the lack or inadequacy of an effective earthing system, (electric shock for example).
For safety reasons do not operate this appliance on an extension
cable. Danger of overheating.
A damaged appliance is dangerous. Switch off at the mains and call the
Service Department for assistance.
Repairs may only be carried out by
suitably qualified and competent engineers to ensure safety. Repairs by unqualified persons could be dan­gerous.
With the “Waterproof system”, the
plastic housing of the water inlet connection contains an electrical com­ponent. It must not be dipped in water.
Do not let small children play with
the dishwasher and its controls or operate it. There is a danger that children playing might shut themselves in the dish­washer. Please supervise its use by the elderly or infirm.
Do not use solvents in the dish-
washer. Danger of explosion!
Avoid inhalation of powder deter-
gents.
The electrical safety of this ap-
pliance can only be guaranteed when continuity is complete between the appliance and an effective earthing system. It is imperative that this basic safety requirement is tested and where there is any doubt the electrical system in the house is checked out by a quali­fied electrician. The manufacturer can-
6
Warning and safety instructions
Dishwasher detergents contain irri-
tant or corrosive ingredients. They can cause burning in the mouth and throat if swallowed, or inhibit breathing. Keep children away from detergents and from the dishwasher when the door is open. There could be deter­gent residues in the appliance.
To avoid the danger of children
coming into contact with the dish­washer detergent: Only put it into the detergent dispenser the programme, and then secure the door with the child safety lock. For models with “Delay Start” option make sure the detergent dispenser is dry before putting in detergent. Wipe dry if necessary. Detergent will clog if poured into a damp dispenser and may not be thoroughly dispensed. If the door is open at the end of a pro­gramme, children may come into con­tact with this residue.
Water in the dishwasher must not
be used as drinking water.
Appliances with a cutlery basket:
items of cutlery are cleaned and dried more efficiently if placed in the basket handles downwards. You may however, prefer to place cutlery with sharp points with the handles upwards.
Always disconnect the appliance
from the electrical supply for main­tenance work (switch off at wall socket and remove plug, screw out fuse in countries where this is applicable).
just before starting
The following notes should help to avoid material damage
The voltage and frequency shown on the data plate must match the
mains supply in the house.
Only use detergents formulated for domestic dishwashers. Do not use
washing-up liquid.
Do not use commercial or indus-
trial detergents as these may dam­age material and there is a risk of severe chemical reaction.
Inadvertently filling the salt reser-
voir with dishwasher detergent al­ways leads to damage to the water sof­tener. Make sure that you have picked up the right packet of dishwasher salt before filling the salt reservoir.
Inadvertently filling the rinse aid
reservoir with powder or liquid detergent always leads to serious dam­age to the reservoir. Only use rinse aid formulated for domestic dishwashers.
Do not sit or lean on the opened
door. This could cause the dish­washer to tip and be damaged.
Plastic items which cannot with-
stand being washed in hot water, e.g. disposable plastic containers, or plastic cutlery should not be cleaned in the dishwasher. The high temperatures could cause the material to distort.
7
Warning and safety instructions
The Miele Waterproof System of-
fers protection from water damage, provided the following conditions are met:
– the dishwasher is correctly installed
and plumbed in
– the dishwasher is properly main-
tained and parts are replaced where it can be seen that this is necessary
– the stopcock has been turned off
when the machine is not used for a longer period of time (e.g. during holidays).
In countries where there are areas
which may be subject to infesta­tion by cockroaches or other vermin, pay particular attention to keeping the appliance and its surroundings in a clean condition at all times. Any dam­age which may be caused by cock­roaches or other vermin will not be covered by the appliance guarantee.
Dishwashers with visible heating ele­ments
For appliances with the heating ele-
ment in the wash cabinet do not touch the element during or directly after the end of a programme, you could burn yourself.
Disposal of your old machine
When disposing of an old dish-
washer first make it unusable. Dis­connect, cut off the cable and the plug from the cable. Make the door lock inoperative, so that children cannot accidentally shut them­selves in. Make appropriate arrange­ments for the safe disposal of the ap­pliance.
The manufacturer can not be held responsible for any damage caused by non-observance of the Warning and Safety instructions.
Some plastic items could melt or
catch fire if they were to come into contact with the heating element. Therefore always place plastic items or any other items which may not be com­pletely heat resistant in the upper bas­ket and ensure they cannot drop through. Any items which are too small to be lodged securely in the upper bas­ket should not be cleaned in the dish­washer.
8
Caring for the environment
Disposal of the packing material
The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled.
Caring for the environment
Energy saving washing
These dishwashers are exceptionally ef­ficient in their use of water and elec­tricity. You can make the most of your appliance by following these tips:
Rather than just throwing these ma­terials away, please ensure they are of­fered for recycling.
Disposal of your old machine
Old machines contain materials which can be re-cycled. Please contact your local authority or scrap merchant about potential recycling schemes, before dis­posing of the appliance.
Ensure that the machine presents no danger to children while being stored for disposal. See the appropriate sec­tion in the Warning and Safety instruc­tions.
If your household water system is suitable, this dishwasher can be con­nected to a hot water supply, for fur­ther economies. However, if your water is heated by electricity we would still recommend connection to cold water. In the UNIVERSAL 55° programme, depending on the capacity of the dishwasher, when connected to hot water at 55°C up to 0.7 kWh of elec­trical energy is saved. The hot water provides this energy, and the ap­prox. 0.13 l oil or 0.14 m needed to heat the water might be considerably more cost effective. Although all stages of the wash then take place with hot water, savings are made in cost, time and energy.
Make full use of the baskets without overloading the dishwasher for most economical washing.
For small loads: Select the additional “Top Solo” op­tion (see section “Additional options”)
3
natural gas
Choose the programme to suit the type of crockery being washed and the degree of soiling.
If baskets are only half full use the ECONOMY programme.
Use the correct dosages of deter­gent.
9
Before using for the first time
Before using for the first time
Before using for the first time please note the following points:
See the relevant sections for detailed in­formation on the points below.
Load the crockery correctly
Load the crockery so that water will come into contact with all surfaces.
This ensures that they will be properly cleaned.
Setting the water softener
The water softener unit must be set to deal with the water hardness level in your area. The salt reservoir must also filled with water and then with dish­washer salt. Never fill with dishwasher powder detergent.
Filling the salt reservoir with deter­gent by mistake will cause serious damage to the water softener. Please check every time before re­filling that the package contains dishwasher salt.
Add rinse aid
Only use rinse aid formulated for do­mestic dishwashers.
Inadvertently filling the rinse aid reser­voir with powder or liquid detergent, or washing up liquid, will cause serious damage to the reservoir.
Do not use washing up liquid
Only use detergent formulated for do­mestic dishwashers.
first be
The spray arms must not be blocked by items which are too tall for the bas­ket or which hang through. If necessary manually rotate the spray arms to test.
Add the correct amount of detergent
Follow the detergent manufacturer’s recommendations on how much deter­gent to use. Not using enough will lead to poor wash results. The amount to dis­pense will depend on the type of deter­gent and programme selected.
Read the notes on dosage given in the programme chart.
Cleaning results may vary from brand to brand. If you are not satisfied with the results from one brand try another quality brand before contacting the Customer Service Department for ad­vice.
It is important to choose the correct programme
The NORMAL programme and the UNIVERSAL programmes are ideally suited to everyday loads. See the pro­gramme chart for descriptions of other programmes.
10
The filter combination in the base of the wash cabinet and the spray arms must be kept clean.
These should be regularly inspected and cleaned if necessary.
Opening and closing the door
To open the door
Opening and closing the door
Child safety lock
Press the release catch inside the door grip.
If the door is opened during operation all functions are automatically inter­rupted.
To close the door
Push the baskets right in Lift the door upwards and push until
it clicks into position
The child safety lock is designed to deter children from opening the dish­washer door.
Use the key provided to turn the child safety lock to the required set­ting.
Horizontal setting = The door is locked.
Vertical setting = The door can be opened.
11
Water softener
Water softener
It is not necessary to reactivate with salt if the degree of hardness in the local supply is permanently under 70 mg/l, (0.7 mmol/l, or 4 °d German scale).
Your local water supplier will advise you on the water hardness of your area.
Above 70 mg/l (0.7 mmol/l, or 4 °d Ger­man scale) water must be softened. This is to avoid the build-up of calcium deposits on crockery and cutlery, and in the dishwasher, and also to increase the effectiveness of the detergent.
To ensure a steady supply of soft water the built-in water softener must be:
1. correctly set and
2. the salt reservoir must be filled with
dishwasher salt for reactivation.
The dishwasher is set at the factory to operate to a hardness level of 400 - 630 mg/l (4.0 - 6.3 mmol/l, or 22 ­35 °d German scale).
Setting the water hardness level selector in the wash cabinet
There are six settings on the selector.
Setting °d mg/l °f
1 4-14 70-250 7-25 2 15-21 270-380 27-38
3* 22-35 400-630 40-63
4 36-47 650-850 65-85 5 48-65 860-1170 86-117 6 66-70 1190-1260 119-126
* factory setting
If your water is harder or softer than this the factory setting will need to be adjusted.
12
Use a coin or screwdriver to adjust the water hardness level selector in the wash cabinet. There is a click as
each setting is reached. Example: The water hardness level is 320 mg/l. The water hardness level selector must
be set to setting 2, 270 - 380 mg/l (15 - 21 °d German scale).
Filling the salt reservoir
Please only use special coarse grained dishwasher salt for reactivation, as other salts may contain insoluble addi­tives which can impair the functioning of the softener.
The salt reservoir holds approx. 2 kg of salt.
Inadvertently filling the salt reservoir
dishwasher detergent always
with leads to tener. Make sure that you have picked up the right packet of before filling the salt reservoir.
Remove the bottom basket. Unscrew the salt reservoir cap.
damage to the water sof-
dishwasher salt
Water softener
Before filling the salt reservoir for the first time: Fill the salt reservoir with approx. 2 litres of water.
Place the funnel (provided) in place.
Fill carefully with salt
(As it is filled displaced water will run
out).
Clean salt from the screw threads of
the socket.
Screw the cap on firmly.
Run the “PRE-WASH” programme
immediately. This removes any
traces of salt from the cabinet. This
is not necessary if “UNIVERSAL” or
“UNIVERSAL PLUS” is the next pro-
gramme to be run.
13
Water softener
Salt indicator
When the salt reservoir is empty the “Salt” indicator light comes on. The reservoir should be refilled with dish­washer salt for reactivation.
Note
With water that is very soft, i.e. at a level constantly below 70 mg/l (4°d), no reactivation salt needs to be added. As the salt reservoir is empty the salt indi­cator light will come on. In this case the light is of no significance.
The “Salt” indicator light has also been designated for future programme up­dates, (see “After Sales Service”).
14
Adding rinse aid
Rinse aid is necessary to ensure that water does not cling and leave marks on crockery during the drying phase. Rinse aid is poured into the storage reservoir and the amount set is dis­pensed automatically. The rinse aid reservoir holds approx. 130 cm
3
.
Inadvertently filling the rinse aid reservoir with liquid detergent) always causes serious damage to the reservoir. Only pour domestic dishwashers into the reser­voir.
powder detergent (or
rinse aid formulated for
Adding rinse aid
Add rinse aid when the indicator
light “Rinse aid” on the control panel
comes on.
Although it is possible to use hold vinegar with a max. 5% acid content, or liquid citric acid up to 50% acid as an alternative, the re­sulting rinsing and drying quality will not be as good as when rinse aid is used. Do not use vinegar with a high acid content (e.g. vinegar essence 25% acid). This must use would damage the dishwasher.
not be used as its
house-
Press the button (in the direction of
the arrow) until the flap springs open.
15
Adding rinse aid
Setting the dosage
Add rinse aid only until it is visible on the surface of the filter in the open­ing.
Close the flap firmly. The flap must audibly engage, other­wise water could get into the rinse aid storage container during the pro­gramme.
Mop up any split rinse aid. This pre­vents over-forming occuring during the next programme.
The flap should normally remain closed. Only open it for adding more rinse aid!
Wait until the “Rinse aid” indicator on the control panel lights up before ad­ding more rinse aid.
The dosage adjuster (see arrow) in the opening has settings from 1 to 6. It is set to 3 at the factory, as the recom­mended dose.This setting dispenses approx. 3 ml rinse aid per programme.
If there are flecks on glasses after
drying use a higher setting.
If smearing appears on crockery use
a lower setting.
16
Loading the dishwasher
Loading the dishwasher
Note
Load the crockery so that water will come into contact with all surfaces. This ensures that they will be properly cleaned.
Do not place crockery and cutlery in­side other pieces where they may be concealed.
Hollow items e.g. cups, glasses etc. must be inverted in the basket.
Deep based items should be placed at an angle such that water runs off them freely.
Tall narrow hollow pieces should be placed in the centre of the basket, rather than in the corners, to ensure good coverage of water.
Small pieces should be placed on the cup racks. Cups should be on the lower rack and bowls on the top rack so that water reaches all pieces.
Some foodstuffs may contain natural
dyes, e.g. carrots, tomatoes or ket-
chup. Plastic items in the dish-
washer may discolour if large quan-
tities of these foodstuffs find their
way into the appliance on the croc-
kery.
The stability of the plastic items is
not affected by this discolouration.
The spray arms must not be blocked by items which are too tall for the basket or which hang through. If necessary manually rotate the spray arms to test.
17
Loading the dishwasher
Loading the dishwasher
Loading examples
Bottom basket
Larger and heavier items such as plates, serving platters, saucepans, bowls. Depending on the dishwasher model glasses may only be cleaned in the bottom basket if it is fitted with a special glassware insert or if there is a special bottom basket.
Height limit
The height guard at the base of the upper basket is there to protect the middle spray arm. No object placed in the lower basket should stand higher than this guard.
Dishwashers with cutlery tray
Dishwashers with cutlery basket
18
Loading the dishwasher
Upper basket
Small, lightweight, delicate items such as cups, saucers, glasses, dessert bowls, etc.
Note for “Top Solo”
If a wash programme has been se­lected with the additional option “Top Solo”, all crockery must be loaded into the upper basket and cutlery tray. See the “Additional options” chapter for fur­ther information.
As the middle spray arm also directs water downwards, lightly soiled plates or platters can be placed in the bottom basket if there are large spaces be­tween them. bowls or other hollow containers in the bottom basket. See Section on “Addi­tional option - Top Solo”.
For dishwashers with a cutlery basket, spread the cutlery out. See also the Section on “Additional op­tions Top Solo”.
Do not place dishes,
19
Loading the dishwasher
Loading the dishwasher
Cutlery
Dishwashers with cutlery basket:
Unsorted cutlery should be placed in the cutlery basket, handles facing downwards.
You may, however, prefer to place cutlery with sharp points with the handles upwards.
Place small spoons in the individual slots to either side of the cutlery basket.
Larger items like soup ladles, long knives and mixing spoons should be placed lying down across the front of the upper basket.
20
Spoon inserts for cutlery basket
Use the inserts supplied when washing heavily soiled spoons, e.g. tablespoons and serving spoons.
The inserts separate the spoons to allow a space between them, for the water jets to reach the entire surface.
Loading the dishwasher
Place the spoons into the inserts with
the handles facing downwards. Only
use alternate slots.
When needed place one insert at the front and one at the back of the cut­lery basket.
Removing the inserts:
Press the catches (which are already clicked in) inwards (if necessary use a spoon handle) and pull the inserts upwards and out.
21
Loading the dishwasher
Loading the dishwasher
Dishwasher with cutlery tray (SC models):
For best results cutlery should be grouped in zones, one for knives, one for forks, one for spoons etc. This makes unloading much easier.
Larger items like sauce ladles, cake slices, long knives and mixing spoons can be placed lengthwise in the trough in the centre of the tray.
Ensure that spoon heads are in contact with at least one of the grips in the cut­lery tray. This way they cannot collect water.
The upper spray arm must not be blocked by items which are too big, e.g. cake slices.
The cutlery tray insert is removable (de­pending on model).
22
Cutlery with round or oval handles should be placed with the heads in the grips as this prevents item slipping.
If putting the spoons this way round, make sure the spoon heads touch at least one of the strips on the floor of the tray, so that the water still runs off.
Loading the dishwasher
Flap up racks
Loading the dishwasher
Positioning rail
(standard feature depending on model)
Can either be used for a second row of cups or raised upwards to make room for tall items.
For easy sorting and removing of croc­kery the positioning rail can be rested to one side.
Raise it again afterwards so that croc­kery can rest against it in the basket.
23
Loading the dishwasher
Loading the dishwasher
Adjusting the upper basket
(depending on model) In order to gain more space for taller
pieces of crockery in the bottom or upper basket, the upper basket can be adjusted in three steps with 2 cm be­tween each step.
Pull out the upper basket and loosen the two locknuts on either side of the basket.
Adjust the basket up or down to the right height.
Depending on the setting of the upper basket the following dimensions can be accommodated:
Dishwashers with cutlery tray
Dishwasher G 6XX
(see data plate for model number)
Upper
basket
position
Top 15.5 30
Middle 17.5 28
Bottom 19.5 26
Dishwasher G 8XX
(see data plate for model number)
Upper
basket
position
Top 20.5 30
Middle 22.5 28
Bottom 24.5 26
plates Ø in cm
Upper
basket
plates Ø in cm
Upper
basket
Lower
basket
Lower
basket
Tighten the locknuts.
The upper basket can also be set to an angle, with one side high, and the other side low. Ensure however that the bas­ket can be inserted smoothly into the cabinet.
24
Dishwashers with cutlery basket
Dishwasher G 6XX
(see data plate for model number)
Upper
basket
position
Top 21.5 30
Middle 23.5 28
Bottom 25.5 26
plates Ø in cm
Upper
basket
Lower
basket
Items not suitable for dishwashers
Items not suitable for dishwashers
– cutlery with wooden or horn handles, – wooden or plastic chopping boards, – glued items, e.g. old knives with
handles which have been glued on, – hand-made craft items, – copper or tin items, – plastic items which are not heat-resis-
tant.
Please note
Silver and aluminium items can suf-
fer some discolouration.
– Aluminium components (e.g. grease
filter) must not be cleaned with caus­tic alkaline commercial or industrial detergents. This may damage ma­terial or, in extreme cases, cause severe chemical reaction.
Silver, treated with a silver polish
may still be damp or spotted at the end of a programme, where water has not run off smoothly. It may need rubbing dry with a soft cloth. treated in a usually dry at the end of a pro­gramme but may discolour.
Colours painted over a glaze may
fade after many washes.
silver immersion dip is
Silver,
– Clouding may occur on
frequent washing.
Important:
Washing delicate glassware in the ECONOMY 55 ° programme, (or for models where the programme is available, GENTLE 45°C) might re­duce the risk of clouding.
There are no standard guidelines for washing glassware. When in doubt wash by hand.
When purchasing new crockery, cut­lery and glassware, make sure they are dishwasher safe.
glasses after
25
Adding detergent
Adding detergent
Only use detergents formulated for domestic dishwashers. Do not use washing up liquid.
Selecting detergent
Recently almost all detergent manufac­turers have launched with a different composition, in addition to standard types.
new detergents
Please note Dishwasher detergents contain irri­tant or corrosive ingredients. They can cause burning in the mouth and throat if swallowed, or inhibit breathing. Keep children away from detergent and from the dishwasher when the door is open. There could still be detergent residues in the cabinet. To avoid the danger of children com­ing into contact with the dishwasher detergent: only put it into the detergent dispen­ser just before starting the pro­gramme.
Should you experience difficulties when using these types of products, please contact Miele Customer and Technical Services Department, or the detergent manufacturer’s own Advisory Service.
new dishwashing detergents, al-
These though welcome from an ecological point of view, react to a different degree from conventional products to water hardness. The drawbacks may only become apparent after a prolonged period of use.
The following problems may occur:
– White deposits on crockery and
inner cabinet.
– Increased etching in the form of a
bluish sheen on the surface of glass­ware.
– Discolouration of silverware.
Appearances of this nature are generally caused by the detergent used and are not attributable to any malfunctioning of the dishwasher it­self.
26
Adding detergent
Preventive measures:
1. If you wish to continue using the new
chlorine and phosphate-free pro-
ducts, the following is recommended: – Set the water hardness selector one
setting higher than recommended in
the “Water softener” chapter, if the
water hardness is at the top of the
scale (except with setting 6).
Example:
above 610 mg/l (34 °d ) set the
water hardness selector to setting 4. – Try out an environmentally friendly
detergent of the same type from an-
other manufacturer.
2. If you are still dissatisfied with the re-
sults, we recommend the use of
chlorine-free but not phosphate-free
detergent. – The instructions given in this book
for setting the water softener and dis-
pensing detergent remain valid.
3. If results are still not to your satisfac-
tion, you should revert back to using
conventional
both chlorine and phosphate. – The instructions given in this book
for setting the water softener and dis-
pensing detergent remain valid.
detergents containing
Dishwasher detergent must be added before each programme (except PRE­WASH).
– Pour powder or liquid detergent into
the dispenser.
– Dishwasher detergent tablets can be
put at various places in the wash cabinet, (follow the manufacturer’s advice on the packet).
Detergent manufacturers give the re­quired amount of detergent in ml (or g) on the packaging.
For the NORMAL programme and the UNIVERSAL programmes use at least 30 ml (or g) detergent unless advised to use more by the manufacturer, then use what they advise.
The amount to dispense will depend on the type of load and the programme se­lected. See the programme chart on the next pages for advice on amounts to dis­pense.
If you buy detergent in bulk please ensure that the container is always properly sealed after use. Otherwise the detergent can lose its effective­ness.
Should you experience difficulties when using these types of products, please contact the detergent manufacturer’s own Advisory Service.
27
Adding detergent
For information: Compartment I takes max. 25 ml, Com­partment II max. 80 ml. There are hori­zontal markers to assist with dispensing in Compartment II, indicat­ing the level in ml.
Press the opening catch on the con­tainer flap. The flap will spring open.
The flap is always open at the end of a programme.
28
Pour in the required amount of deter­gent.
Shut the flap.
Choosing a programme
Choose your programme according to the type of load and how dirty it is.
In most cases this will be the NORMAL programme or one of the UNIVERSAL programmes.
NORMAL 55°
(without pre-wash) or
UNIVERSAL 55° or 65°
(with a pre-wash) These programmes are ideally suited to
everyday loads i.e. mixed loads with va­rying degrees of soiling.
For particular needs there are special programmes:
The different programmes and their uses are described on the next two pages in the Programme chart.
You can also choose the additional op­tion “Top Solo” for each programme. See the “Additional options” section for further information.
Choosing a programme
29
Programme chart
Programme chart
Programme When to use Detergent
containing
chlorine
Compart-
ment I
(Pre-wash)
Compart-
ment II
(Wash cycle)
Normal- and Universal-Programmes
NORMAL 55 ° for normal everyday loads,
particularly suitable for chlorine-free detergents
UNIVERSAL 55 ° for normal everyday loads 20 % 80 % 100 %
100 % 100 %
chlorine-
1)
free
Compart-
ment II
(Wash cycle)
2)
UNIVERSAL PLUS 55 °
UNIVERSAL 65 ° as UNIVERSAL 55 °,
as UNIVERSAL 55 °,
3)
but with longer wash time for heavily soiled loads, particularly suitable for chlorine-free detergents
but with higher wash temperature for stubborn dried-on particles
20 % 80 % 100 %
20 % 80 % 100 %
Special-Programmes
ECONOMY 55 ° for full loads with very light soiling , e. g.
coffee cups or: for half a normal everyday load, for cleaning normally soiled every day loads,
GENTLE 45 ° ,,Gentle programme“ for lightly soiled crockery
and for heat sensitive crockery
PRE- WASH for rinsing crockery to avoid smells if a
complete cycle is not needed
The amount dispensed will depend on the type of detergent being used:
1) Use this method for: – detergents containing phosphates and chlorine (except liquid detergent) Divide the total amount proportionally between compartment I and compartment II.
2) Use this method for: – detergent which is chlorine and phosphate free – detergent which is chlorine free but contains phosphates – liquid detergent In this instance the whole amount is placed in compartment II
For the NORMAL programme and the UNIVERSAL programmes use at least 30 ml (or g) detergent un­less advised to use more by the manufacturer, then use what they advise.
50 % 50 %
50 % 50 %
“Top Solo” option is selected the appropriate amount of detergent according to the degree of soil
If the should be added to
compartment II only (approx 2/3 of the total amount required for full load).
30
Prewash Main
wash
Programme cycle Consumption Duration
Energy kWh 4)Water Minutes (approx.)
Interim-
rinse
Final-
rinse
Drying phase
Water
cold
(15 °C)
Water warm
(55 °C)
Litres
Water
cold
(15 °C)
Water warm
(55 °C)
X
55 °
XX
55 °
XX
55 °
XX
65 °
X
55 °
XX
45 °
X 0.06 0.06 5 8 8
3) Standard programme (see section on “Comparison tests”)
4) The energy consumption is 0.1 kWh higher for G 8XX models (except for the PRE-WASH programme).
5) with half loads: G 6XX – 6 place settings, G 8XX – 7 place settings
XX
65 °
XX
65 °
XX
65 °
XX
65 °
XX
55 °
XX
55 °
X 1.2 0.6 16 80 67
X 1.2 0.6 20 85 72
X 1.2 0.6 20 108 95
X 1.3 0.7 20 88 74
X 1.1
X 1.1 0.3 20 68 55
5)
0.4
5)
16 60
5)
50
5)
31
Switching on and off
Switching on and off
Switching on
Close the door. Turn on the stopcock, (if previously
closed). Press the “On/Off”-switch (14). The control light “On” (19) lights up.
Starting a programme
Turn the Programme selector switch (20) clockwise or anti-clockwise to the required programme.
The programme starts. Within the first 30 seconds after start-
ing a programme select the addi­tional option “Top Solo” if required (see section “Additional options”).
Do not cancel a programme prema­turely. This can cause internal pro­gramme steps such as reactivating the softener to be left out.
Programme sequence display (19)
The control light “On” lights up, when the dishwasher is switched on.
control light “Wash/Rinse” lights up
The in the PRE-WASH, MAIN WASH, IN­TERIM RINSE and FINAL RINSE pro­gramme section.
The
control light “Drying” lights up dur-
ing the DRYING programme section.
End of a programme
When the control light “End” (19) lights up in the programme sequence dis­play, the programme has finished.
The dishwasher can now be unloaded (see section “Removing the load”).
If it is left closed, the fan will continue for a few more minutes to reduce any remaining moisture. This is recommended if the crockery is not required immediately.
32
Switching on and off
Switching off
At the end of a programme:
Turn the programme selector to “STOP”.
The control light “End” goes out. Press in and release the
“On/Off”-button (14).
If the dishwasher is not to be used for a long period of time, e.g. whilst on holi­day:
Turn off the stopcock.
Programme interruption
A wash programme is interrupted as soon as the door is opened. If the door is closed again the pro­gramme will simply continue.
Warning! Water in the dishwasher may be hot. Danger of scalding. Only open the door if absolutely necess­ary and exercise caution when doing so. Before closing the door again hold it for about 20 seconds in the nearly closed position, to enable the tem­perature in the wash cabinet to equalise, and then shut firmly.
Programme change
A programme change can be made at any time. The newly chosen pro­gramme starts as soon as it has been selected. The programme starts from where the other programme was ended.
If when changing a programme the se­lector switch is turned past the “Stop” position, for example from GENTLE 45° to UNIVERSAL 55° and the selector stays for more than 2 seconds at the “Stop” position, the newly selected pro­gramme starts at the beginning of its cycle. The same happens if the programme selector stands for more than two sec­onds between UNIVERSAL PLUS 55° and ECONOMY 55°.
Removing the load
Hot crockery will chip and break more easily. After switching off let it cool down in the dishwasher until it is comfortable enough to handle, before you unload it.
If you open the door fully after switch­ing off, the crockery will cool down much faster.
First unload the bottom basket, then the upper basket and then the cut­lery tray (if you have one) at the very end. This way you avoid water droplets from the upper basket or the cutlery tray falling on to crockery in the bot­tom basket.
33
Additional options
Additional options
Top Solo (17)
With this option the majority of the water is directed only to the top and middle spray arms in the dishwasher. This means that the water jets are aimed only at items in the upper basket and cutlery tray (where fitted).
This additional option is recommended when there is only a small amount of crockery and cutlery to clean which fits into the upper basket and the cutlery tray. N.B. Lightly soiled plates or serving platters can still be placed in the bottom basket if there are large spaces between them. Do not place dishes or bowls or other hollow containers in the bottom basket. If your dishwasher has a cutlery basket place cutlery with space around it.
In some instances adjusting the upper basket to the lowest position can make it easier to accommodate larger plates in this basket.
Because smaller amounts of crockery are being washed the amount of deter­gent recommended by the manufacturer can be reduced (approx. 2/3 of the total amount for a full load). Make sure, how­ever, when reducing the amount dis­pensed that the cleaning result is not af­fected.
By using the “Top Solo” option, water and energy savings are also made. For example in the UNIVERSAL PLUS 55° programme only 14 litres of water and 1.0 kWh of electricity are used.
The additional Top Solo option can be selected for all wash programmes.
Switch on the dishwasher with “On/Off” (14) button.
Turn the Programme selector switch (20) clockwise or anti-clockwise to the required programme.
Within the following 30 seconds:
Press the “Top Solo” button (17). The control lamp next to the button
lights up and the programme starts.
34
Cleaning and care
Cleaning the filters in the wash cabinet
The dishwasher must not be used without all the filters in place!
The filter combination in the base of the wash cabinet should be regularly in­spected and cleaned if necessary.
Cleaning and care
Turn the handle anti-clockwise to re­lease the filters.
Lift and take the filter combination out of the machine. Remove coarse par­ticles and rinse under running water. Use a nylon brush if necessary.
35
Cleaning and care
Cleaning and care
Turn the filter combination over and open the coarse filter by pulling back on the locking device.
Clean the coarse filter under running water, using a brush if necessary, and press the locking device back in.
Important: After cleaning make sure that the lock­ing device is properly locked.
Replace the filter combination so that it lies flat in the base of the wash cabinet. Secure the filter by turning the handle in a clockwise direction.
36
Cleaning and care
Cleaning the spray arms
Particles of food can lodge in the spray arm jets. The spray arms should be inspected and cleaned regularly (approx. every 6 months).
To do this remove the spray arms as fol­lows.
Cleaning and care
Dishwashers with cutlery basket:
Unscrew the upper spray arm.
Dishwashers with cutlery tray:
Pull out the cutlery tray. Lift up the upper spray arm to en-
gage the tooth-wheel mechanism and then unscrew the spray arm.
Lift up the middle spray arm b to en­gage the tooth-wheel mechanism. Then unscrew the spray arm
Remove the lower basket and take out the
lower spray arm.
c.
Using a sharp pointed object push the food particles into the spray arm jets and rinse well under running water.
Please note: After replacing the spray arms check that they move freely.
37
Cleaning and care
Cleaning and care
Cleaning the drain pump and non-return valve
If water has not been pumped away at the end of a programme the drain pump or the non-return valve might be blocked. They are, however, easy to clean. Watch out for glass splinters, which could cause injury.
Take the filter combination out of the wash cabinet.
Use a jug or bowl to scoop water out of the wash cabinet.
Lift up the non-return valve and rinse under running water.
Raise the locking clamp.
38
The drain pump is situated under the non-return valve (see arrow).
Before replacing the non-return valve check that the drain pump impeller turns with only slight resistance, and that there is no obstruction.
Carefully replace the non-return valve and secure with the locking clamp.
Replace and secure the filter combi­nation.
Cleaning and care
Cleaning the filter in the water inlet
A filter is incorporated in the screw con­nection of the valve on the water inlet hose. The filter must be cleaned when dirty, otherwise insufficient water flows into the wash cabinet.
The plastic housing of the water connection contains an electrical component. It must not be dipped in water.
Cleaning and care
To clean the filter
Fitting an in-line water filter
If the mains water contains a large num­ber of insoluble substances, we recom­mend fitting a large area filter in the connection between the stopcock and the water inlet hose threaded union. These filters can be obtained from the Miele Spares Department (Part No.:
75577).
Disconnect the appliance from the mains supply (switch off at the main socket and pull out the plug, switch off the appropriate circuit at the fuse­box or withdraw the mains fuse).
Turn off the stopcock and unscrew the inlet hose.
Carefully remove the rubber seal. Withdraw the filter using pointed
pliers and clean by rinsing under run­ning water.
Replace filter and seal. Make sure they are sitting correctly!
Screw back into place on the water inlet, taking care that it goes back on straight.
Turn on the stopcock gradually to test for leaks. If there is a leak: Screw the connections on more tightly.
39
Cleaning and care
Cleaning and care
Cleaning the wash cabinet
In general the wash cabinet is self­cleaning, provided that the correct amount of dishwasher detergent is used.
If however there are lime scale or grease deposits these can be removed with a proprietary dishwasher cleaner.
Cleaning the door and the door seal
Wipe the door seal regularly with a damp cloth and remove any par­ticles of food.
Wipe away any residue of food and drink spillage from the sides of the dishwasher door. These are not part of the wash cabinet and are not reached by water from the spray arms.
The facia panel
This should only be wiped with a damp cloth, or a suitable plastic cleaner.
Do not use an abrasive cleaner, a glass cleaner or an all-purpose cleaner. Because of their chemical composition they could cause serious damage to plastic surfaces.
The front of the dishwasher
Laminate fronts should be cleaned using a suitable proprietary cleaning agent.
Fronts made from wood should only be cleaned using a damp cloth or leather and dried with a soft cloth.
Do not use any cleaner containing ammonia or thinners.
40
Checking the water level
If the water pressure (flow rate at the take-off point) is too low, i.e. less than
1.0 bar, too little water will flow into the wash cabinet.
To ensure an accurate assessment open the stopcock fully and run the PRE-WASH programme once (with­out crockery) to bring water into the system.
Run the PRE-WASH programme again. After approx. 3 minutes open the door and remove the bottom bas­ket from the machine.
Checking the water level
The water level is correct when dimen­sion “X” is at least 4 mm.
If it measures less, then the water in­take time must be increased, (see section on extending water inlet time).
41
Extended water inlet time
Extended water inlet time
If the water pressure is less than 1.0 bar not enough water flows into the wash cabinet. Water inlet time must be extended.
Switch the dishwasher off with the “On/Off” button.
Turn the programme selector to STOP.
Hold the “Top Solo” button pressed
at the same time switch the
in and dishwasher on with the “On/Off” but­ton. Release the “Top Solo” button again within two seconds.
The “On” indicator lights up and the “Wash/Rinse” indicator flashes.
Important: If a different indicator flashes or lights up start the procedure from the beginning again. Exception: The indicator lights “Salt” or “Rinse aid” light up at the beginning if dish­washing salt or rinse aid have not been added, or need to be topped up.
Turn the programme selector to UNIVERSAL 65° .
If the indicator light next to the “Top Solo” button Water inlet time = normal
If the indicator next to the “Top Solo” button Water inlet time = extended
Press the “Top Solo” button to change the setting.
Turn the programme selector to STOP.
Switch the dishwasher off with the “On/Off” button.
The change to the water inlet time is now stored in memory.
does not light up:
lights up:
42
Problem solving guide
With the aid of the following explana­tory notes, minor faults can be cor­rected without contacting the Miele Ser­vice Department.
Any work on the electrical compo­nents of the appliance should only be carried out by a suitably quali­fied and competent person in ac­cordance with local and national regulations. Unauthorised repairs could be dangerous.
If, however, you are unable to correct the problem, the Miele Service Depart­ment should be contacted.
Faults/possible causes
The dishwasher does not start
– The door is not properly closed. – The plug is not properly inserted. – The fuse is defective/has blown.
The dishes are not cleaned.
– The dishes are incorrectly loaded.
Problem solving guide
White residue on cutlery and crockery
– No salt in the salt reservoir.
Fill the salt reservoir with dishwasher salt for reactivation – see section on “Water softener”.
– Salt reservoir lid has not been
screwed on properly.
– Not enough rinse aid.
Use a higher dosage setting – see “Adding rinse aid”.
Water in the wash cabinet at the end of a programme
– The outlet hose is kinked. – The drain pump is blocked – see
“Cleaning and care”.
– Foreign bodies are obstructing the
non-return valve – see “Cleaning and care”.
Before removing the obstruction:
Turn the programme selector to STOP. Switch off the dishwasher with the
ON/OFF button.
– The correct amount of detergent was
not dosed – see “Programme chart”.
– The filters in the wash cabinet are
not clean – see “Cleaning and care”.
– The spray arm jets are blocked – see
“Cleaning and care”.
– The wrong programme was selected
– see “Programme chart”.
43
Problem solving guide
The indicator lights “Wash/Rinse”, “Drying” and “End” (19) FLASH at the same time:
Water inlet fault The dishwasher stops during the pro-
gramme. – The stopcock is shut. – The filter in the screw connection of
the valve on the water inlet hose is blocked – see “Cleaning and care”.
– Too little water flows into the wash
cabinet. This may be due to insuffi­cient water pressure at the intake (flow pressure at the water inlet). In this case the water inlet time can be extended – see the section “Ex­tending the water inlet time”.
Before removing the obstruction:
Turn the programme selector to STOP.
Switch off the dishwasher with the ON / OFF button.
Water drainage fault The dishwasher stops during the pro-
gramme. There may be water left in the wash cabinet.
– The drain hose is kinked. – The drain pump is blocked – see
“Cleaning and care”.
– Foreign bodies are obstructing the
non-return valve – see “Cleaning and care”.
Before removing the obstruction:
Turn the programme selector to STOP.
Switch off the dishwasher with the ON / OFF button.
If the indicator lights still flash when you start a new programme, or if the cause for them to flash was not one of those listed here, there may be a technical fault.
44
Please call the Service department.
In some cases the PRE-WASH pro­gramme can still be carried out in spite of this technical fault.
Problem solving guide
After sales service
If you are unable to remedy a prob­lem yourself, please contact:
– your Miele Dealer or – the Miele Service Department.
See back cover for addresses. Please quote the model type and
number of your appliance.
This information can be found on the data plate inside the door.
Future updates
The LED marked PC is reserved for the service engineer, for updates in future years to your machine.
When for example technological devel­opments offer advanced modifications to your existing programme cycles, a service engineer will be able to input these into your machine controls.
Miele will provide information when such possibilities become available.
45
Special accessories
Special accessories
Bottle holder
(depending on model)
The bottle holder (e.g. for milk or baby bottles) can be used in the bottom bas­ket.
To achieve good cleaning results the bottle holder should only be placed in the positions marked white – account in the positions marked with
an X.
and on no
Installation - special situations
Brackets to fix the dishwasher under a
marble-type worktop.
Conversion kit (UBS) freestanding dishwasher into a built under model
when a freestanding dishwasher is to be installed under a work surface run.
Decor frame adapter strip for free­standing dishwashers for decor pa-
nels 1 to 4 mm thick. Building-under kit (GDU) to modify an
integrated “i” dishwasher to a built­under dishwasher.
Extended machi n e feet where a height of up to 92 cm (G 6XX) or up to 94 cm (G 8XX) is required.
Plinth facia kit for “i” dishwashers
for kitchens without a complete plinth facia run.
Adapter strips for “i” dishwashers to match the control panel facia to the ad­jacent drawers.
Other special accessories e.g. special inserts for glasses or plates, etc. are available through your Dealer or the Spare Parts Department. See the following list.
46
Inserts
Glass inserts for the bottom basket,
(only available for models with remov­able inserts in the bottom basket).
Glass inserts for the upper basket,
especially for glasses which need a special support.
Comparison tests
Comparison tests
Dishwasher G 6XX (see data plate for model number)
Test standard: IEC 436 / DIN 44990 / IEC 704 / prEN 50242 Amount washed: 12 place settings (full load) Programme tested: UNIVERSAL PLUS 55 ° Amount of detergent: If using a detergent containing chlorine:
5 g in compartment I, and 25 g in compartment II. If using a chlorine-free detergent:
only in compartment II.
30 g
Rinse aid dispensing: Setting 3 (approx. 3 ml, set at factory) Measuring noise: Before starting a programme to measure noise, the
dishwasher door must first be opened completely. Doing this will automatically close the vent exit for the turbothermic drying process as in daily use.
Dishwashers with cutlery basket
Spoon inserts: Fit the two inserts on top of the cutlery basket, (see
Section on loading the dishwasher, spoon inserts). Place six spoons at intervals in each insert.
Upper basket
Bottom basket
47
Comparison tests
Dishwashers with cutlery tray (Dishwasher G 6XX)
Upper basket
Bottom basket
Cutlery tray
48
Comparison tests
Dishwasher G 8XX (see data plate for model number)
Test standard: IEC 436 / DIN 44990 / IEC 704 / prEN 50242 Amount washed: 14 place settings (full load) Programme tested: UNIVERSAL PLUS 55 ° Amount of detergent: If using a detergent containing chlorine:
5 g in compartment I, and 25 g in compartment II. If using a chlorine-free detergent:
only in compartment II.
30 g
Rinse aid dispensing: Setting 3 (approx. 3 ml, set at factory) Measuring noise: Before starting a programme to measure noise, the
dishwasher door must first be opened completely. Doing this will automatically close the vent exit for the turbothermic drying process as in daily use.
Upper basket
Bottom basket
49
Comparison tests
Cutlery tray
50
Comparison tests
Comparison tests
Dishwasher G 6XX (see data plate for model number)
Test standard: IEC 436 / DIN 44990 / IEC 704 / prEN 50242 Amount washed: 6 place settings (half load) Programme tested: UNIVERSAL PLUS 55 ° Amount of detergent: 20 g Rinse aid dispensing: Setting 3 (approx. 3 ml, set at factory) Measuring noise: Before starting a programme to measure noise, the
only in compartment II
dishwasher door must first be opened completely. Doing this will automatically close the vent exit for the turbothermic drying process as in daily use.
with “Top Solo”
Dishwashers with cutlery basket
Spoon inserts: Fit the two inserts on top of the cutlery basket, (see
Section on loading the dishwasher, spoon inserts). Place three spoons at intervals in each insert.
Upper basket
Lower basket
51
Comparison tests
Dishwashers with cutlery tray (Dishwasher G 6XX)
Upper basket
Cutlery tray
Double the distance between the pieces of cutlery in the cutlery tray.
G 8XX dishwashers
(see data plate for model number)
Loading: half load, spread out as for the G 6XX model
Amount washed: 7 place settings
Lower basket
52
Installation instructions
53
Contents
Contents
Installing a freestanding dishwasher (only for G 6XX model dishwashers). . . . 55
1. Establishing the height of the decor panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
2. Matching the door height. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Integrated “i” dishwashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
1. Fit worktop protection (“niro” stainless steel coverplate). . . . . . . . . . . . . . . . . . 63
2. Building the dishwasher into a niche . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
3. Fitting the facia panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
4. Matching the facia panel to the dimensions of the adjacent drawer fronts . . . . . . 68
5. Fitting the (matching) door front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
6. Adjusting the door springs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
7. Levelling and securing the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
8. Matching the plinth facia of a kitchen run. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Plumbing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Connection to the water inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Drainage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
54
Installing a freestanding dishwasher
Installing a freestanding dishwasher
"Freestanding" dishwashers
The dishwasher must be level and stable when installed.
Any unevenness in the floor level can be compensated for by adjust­ing the four screw feet.
The adjustment range is approx. 1 cm (85 - 86 cm total height).
Height adjustable door
The freestanding dishwasher is fitted with a height adjustable door, to match adjacent kitchen units. The adjustment range is approx. 7 cm.
The decor panel of the dishwasher can be exchanged for a panel to match your kitchen decor.
With a (UBS) conversion kit (freestand­ing dishwasher into a built under model), a freestanding dishwasher can be installed under a work surface run.
55
Installing a freestanding dishwasher
Installing a freestanding dishwasher
1. Establishing the height of the decor panel
Adjust the dishwasher to the height re­quired before establishing the height of the decor panel. The upper edge of the control panel facia and the top edge of an adjacent door or drawer must be at a matching height.
Measurement "X" equals the distance from the lower edge of the dishwasher door to the lower edge of an adjacent kitchen unit door front.
The decor panel supplied has a height of 604 mm. This or a new decor panel must be shortened by the measure­ment "X" for matching.
56
Installing a freestanding dishwasher
Installing a freestanding dishwasher
Adapting the height of the decor panel supplied
Mark the measurement "X" on the left and right hand side of the decor panel and on the decor frame strips.
Establishing the height of a new decor panel
The decor panel supplied with the dish­washer can be exchanged for a panel to match your kitchen decor.
Take off and shorten the decor frame strips (see Step 2), the decor panel and the packing card.
The new panel must have the following measurements:
Width: 587 mm
Thickness: Minimum 1 mm and maximum 4 mm. The packing card originally supplied behind the decor panel must be removed for new panels with a thick­ness of more than 2 mm.
Height: 604 mm minus "X" mm
Mark the measurement "X" on the left and right hand side of the decor frame.
Take off the decor frame strips (see Step 2), the decor panel and the packing card, and shorten the decor frame strips, and the packing card (if used).
57
Installing a freestanding dishwasher
Installing a freestanding dishwasher
2. Matching the door height
The plinth facia and the cover caps at the sides must be removed before the decor frame strips can be unscrewed.
Loosen and remove the fixing screws and push the side decor frame strips downwards until they are free of the dishwasher outer door
panel and can be removed. Push the plinth facia upwards and pull forwards out of the fastening.
Take off the side cover caps.
58
Installing a freestanding dishwasher
Installing a freestanding dishwasher
Bow the panel slightly, draw out from under the control facia and remove.
Shorten the decor frame strips, and the packing card (if used) by meas­urement "X".
When using the decor panel sup­plied: Draw a line to join the two marks for measurement "X". Shorten the decor panel along this line.
Note: When the decor frame strips are short­ened, the hook at the lower edge is cut off. It is however only needed for full length decor frame strips to give addi­tional fixing to the door outer panel.
Loosen the screws b in the door
outer panel, but do not screw out
completely.
Push the lower edge of the adapter
c (corresponding to measure-
plate
ment "X") upwards far enough for its
lower edge to be in a line with the
lower edge of the adjacent kitchen
unit door front(s).
Tighten the screws b in the adapter
plate.
59
Installing a freestanding dishwasher
Installing a freestanding dishwasher
Refit the packing card (if used) and the decor panel. Fit the decor panel into the lower decor frame strip, posi­tion the packing card behind it , bow the decor panel forwards and slide under the control facia panel.
Ensure the decor panel sits correctly. If necessary readjust the height of the adapter plate.
Put back the left and right hand side
decor strips and slide under the con-
trol panel from beneath.
The adapter plate must grip the guide groove at the rear edge of the decor frame strip.
Screw in the fixing screws for the
decor frame strips.
60
Installing a freestanding dishwasher
Installing a freestanding dishwasher
Fit the side cover caps.
Push the plinth strip into the fixing b
and then press downwards c.
Please note: The plinth strip must engage in the side cover cap.
61
Installing integrated “i” Dishwashers
Installing integrated “i” Dishwashers
The “i” model dishwashers are spe­cially designed for building under a continuous worktop.
The front can be fitted with a base unit front to match the kitchen furniture.
By using a decor set GDU “i” model dishwashers can be converted into a built-under “U” model dishwasher. The decor set is supplied with a separ­ate installation instruction leaflet.
To ensure stability, these dish­washers must only be installed under a continuous worktop which must be securely screwed to neigh­bouring units.
Dishwasher G 6XX
(see data plate for model number) Dimensions:
1) with 870 mm machine height
2) with 820 mm machine height
Range of adjustment approx. 5 cm (82­87 cm total height).
Extended machine feet are available at extra cost, (special accessory). These can be used for a machine height of 87 to 92 cm.
Dishwasher G 8XX
(see data plate for model number) Dimensions:
1) with 890 mm machine height
2) with 840 mm machine height
Range of adjustment approx. 5 cm (84­89 cm total height).
Extended machine feet are available at extra cost, (special accessory). These can be used for a machine height of 89 to 94 cm.
62
Installing integrated “i” Dishwashers
1.Fit worktop protection
A stainless steel “niro” coverplate is supplied with the machine to protect the underside of the worktop against steam rising from the machine. The coverplate is supplied as standard with “i” models.
Squeeze sealant from the tube sup-
plied
b into the angle of the “niro”
plate.
Align the “niro” plate c to the front
edge of the worktop – see illustration
- and then use tacks supplied to nail
the “niro” plate to the underside of
the worktop.
On worktops with wood or laminate
edging, the tacks should be nailed
through the holes further back from
the edge.
63
Installing integrated “i” Dishwashers
2.Building the dishwasher into a niche
Connection to water and drainage should be sited beside and not behind the dishwasher for accessibility. Con­nections are usually made in the area under the sink. Many kitchen unit manu­facturers provide a cutout in the base of the sink base unit for the hoses to be fed through. If the base unit has no opening and if there is not an opening through the plinth area for connections, one must be cut. Suggested dimensions: 60 x 110 mm.
For some installation steps it is necessary to pull the dishwasher slightly out of the recess. Therefore do not make these connections until last.
64
Installing integrated “i” Dishwashers
The slides make installation of the dish­washer easier and protect the floor from possible damage when moving the appliance into and out of the re­cess. They are also used for adjusting the height of the rear screw feet.
Adjust the height manually before in­stalling the dishwasher. Leave a space of approx. 5 mm below the worktop to allow the dishwasher to be pushed back easily into the re­cess. Make sure that the dishwasher stands level.
Push the dishwasher right back into the recess. Ensure that drain hose, inlet hose and electric cable are laid to reach the connection point without any kinks.
Press the slides - with the ratchet at the rear - under the screw feet.
65
Installing integrated “i” Dishwashers
Adjust the rear screw feet to the re­quired height.
Higher = turn clockwise Lower = turn anti-clockwise Several turns are needed to adjust 1 mm
in height. A battery-powered screw­driver could be used.
Adjust the front screw feet manually or with a flat blade screwdriver.
It is easier to adjust the screw feet if the weight of the dishwasher is not bearing down on them.
If possible tip the machine slightly. For fine adjustments it may be
necessary to press with a screw­driver against the cogs of the feet.
Screw the feet out until the dishwasher is right up against the underside of the worktop, to which it will be screwed later. Ensure that the dishwasher stands level.
66
Installing integrated “i” Dishwashers
Installation integrated “i” Dishwashers
3. Fitting the facia panel
The facia panel is delivered separately in the colour ordered with the necess­ary accessories. It has to be fitted to the dishwasher when it is being installed.
Attach caps b to the push button switches.
Fit the adapter disc c . Place the seal supplied d in the
groove round the ventilation grille Push the ventilation grille e into posi-
tion. Place the facia panel f in position
and screw into place from the inside using the six screws
Attach the switch knob h.
g.
e.
Only applicable when using the GDU decor set (to convert an “i” version to a
built-under “U” version) If the GDU decor set is being used, the
adapter strips removed, and stored for possible use in the future. See also the separate in­structions for fitting the GDU decor set.
Press out the adapter strips from the fitting slits in the facia panel.
i must first of all be
67
Installing integrated “i” Dishwashers
4.Matching the facia panel to the dimensions of the adjacent drawer fronts
The facia panel can be aligned with the drawer fronts of the kitchen units by ad­justing the spacer bars.
Using an 8 mm socket spanner turn clockwise or anti-clockwise until the required height is reached.
Adjustment range: from 112 mm: facia panel without
spacer bars
to 145 mm: facia panel with four
spacer bars,
to 154 mm: using a fifth spacer bar
(special accessory at
extra cost).
Please note
After adjustment cut off any protruding lengths of the screws.
If necessary some or all spacer bars can be removed.
68
Installing integrated “i” Dishwashers
5.Fitting the (matching) door front
The door of the kitchen base unit (with­out the drawer facia or fittings) is nor­mally used for the door front.
The door front is fixed to the machine door outer panel using a fixing bracket which has to be pre-mounted on the rear of the door front.
Templates are provided to position the fixing bracket and the door front accur­ately.
Fixing brackets are already fitted on the stainless steel door front. This front can­not be shortened.
Door fronts differ in weight and it is therefore essential that the door springs are adjusted (see Step 6) after the door front has been fitted.
On each side of the fixing bracket position a template with the rule markings facing outwards.
Hang the fixing bracket into the slits in the machine door outer panel.
Push the overhanging ends of the templates under the facia panel.
69
Installing integrated “i” Dishwashers
Installing integrated "i" Dishwashers
Adjust the fixing bracket D: The long holes in the machine door outer panel must be aligned with the matching markings on the template.
On the template E mark the height of the top edge of adjacent kitchen base unit doors.
Take off the fixing bracket. Lay the door front down with the rear
side facing upwards.
Lay the bracket on the rear side of the door front and adjust so that:
– the marks on the template for the
upper edge of the adjacent base unit doors match the top edge of the door front.
– The fixing bracket must be the same
distance from the left and right hand side edges of the door front.
Use strips of adhesive tape to hold the bracket in this position.
70
Installing integrated “i” Dishwashers
Installation integrated “i” Dishwashers
Drill the fixing holes to a depth of about 10 mm, using a 2.5 mm drill bit.
Secure the fixing bracket to the door front using the flat-head screws sup­plied.
Take off the templates.
Keep the templates in case the dish­washer is ever fitted with a new door front.
Open the dishwasher door slightly. Adjust the door front for the height
on one side and lightly screw in a T20 Torx screw on this side.
Adjust the door front height on the other side and also lightly screw in a T20 Torx screw on this side.
Shut the dishwasher door. Check the door front for correct align-
ment. If necessary unscrew and readjust.
Once the door front is correctly posi­tioned:
Open the dishwasher door. Tighten all the Torx screws on the
sides. Plug the openings for the fixing
screws using the plastic stoppers provided.
Hang the door front into the slits in the machine door outer panel.
71
Installing integrated “i” Dishwashers
6.Adjusting the door springs
The door springs are correctly adjusted when a half opened door (approx. 45° opening angle) remains in that position when released.
If the door drops down, then the door springs need to be tightened.
If, however, it rises up, then the springs need to be released.
The adjusting screw is located in the upper front strip at the left hand side of the dishwasher.
Open the dishwasher door.
7.Level and secure the dishwasher
To ensure the stability of the dish­washer it must be screwed to the con­tinuous worktop after it has been posi­tioned.
Fit the securing pieces into the slots on both the left and right hand sides.
Push the dishwasher into the recess.
Adjust the door spring using a Torx screwdriver until it is correctly bal­anced: – turn clockwise = tighten – turn anti-clockwise = loosen.
72
Open the dishwasher door.
The hole in the securing piece must line up with the oval hole in the niro steel plate.
Installing integrated “i” Dishwashers
Screw the countersunk screws (3.9 x 22) upwards through the se­curing pieces on the left and right hand sides into the work surface to secure the dishwasher.
For “Corian” or granite worktops there is a special accessory to fix the dish­washer to an adjacent kitchen unit.
Pull the dishwasher approx. 5-10 cm out of its niche.
Ensure that the seal on the top edge of the dishwasher fits directly against the worktop. If this is not the case, adjust the height screws more, (see Step 2).
Fit the lug of each fixing bracket into the guide hole on top of the dish­washer, and then swing to the left or right side respectively.
Push the dishwasher back into the niche, align, and fix to the adjacent kitchen unit(s) with 2 screws (3.5 x 15) for each bracket.
73
Installing integrated “i” Dishwashers
8.Matching the plinth facia of a kitchen run
The plinth area of the dishwasher is nor­mally covered with a plinth run match­ing the kitchen furniture.
The height (H) of the plinth facia around the dishwasher depends on the plinth return (R) and how much the door front extends below the dishwasher door (P).
Place the plinth facia directly in front of the kitchen run but do not attach.
Carefully open the dishwasher door.
If the door front comes into contact with the kitchen plinth when the dishwasher door is opened the plinth facia in the area around the dishwasher door needs to be cut to size.
To do this mark where the edge of the door front comes into contact with the plinth facia.
Cut the plinth facia to size along this line.
Place the plinth facia in front of the kitchen run again and check whether the dishwasher door can be opened fully. If it cannot, trim the plinth facia to the correct size.
74
Secure the plinth facia to the ad­jacent kitchen units.
If your kitchen does not have a plinth run matching the kitchen furniture, the plinth area can be covered with a sep­arate plinth kit, available at extra cost.
Electrical connection
Please follow the installation instruc­tions carefully.
This dishwasher is supplied ready for connection to an a.c. single phase supply, (230 - 240 V 50 Hz for the UK and Australia). It is supplied with a mains cable and moulded plug.
All electrical work should be carried out by a competent person in ac­cordance with national and local regulations. Connection should be made via a fused plug and suitable switched socket which is easily ac­cessible. For extra safety it is advisable to in­stall a residual current device (RCD) with a trip current of 30 mA.
The voltage, rated load and fuse rating are given on the data plate.
Please ensure that these match the household mains supply.
Electrical connection
Important
The wires in the mains lead are col­oured in accordance with the following code:
Green/yellow = earth Blue = neutral Brown = live As the colours of the wires in the mains
lead of this appliance may not corre­spond with the coloured markings ident­ifying the terminals in your plug, pro­ceed as follows:
The wire which is coloured green and yellow must be connected to the termi­nal in the plug which is marked with the letter E or by the earth symbol coloured green or green and yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red (UK), or marked with the letter A for (AUSTRALIA).
z or
WARNING THIS APPLIANCE MUST BE EARTHED
75
Electrical connection
Non rewireable plugs BS 1363
If this machine or appliance is fitted with a non-rewireable plug, the follow­ing information applies:
If the socket outlets are not suitable for the plug supplied with this product, it must be cut off and an appropriate plug fitted.
The plug cut from the flexible cord should be disposed of and on no ac­count be inserted into a socket else­where in the house (electric shock ha­zard).
The fuse cover must be refitted when changing the fuse, and if the fuse cover is lost, the plug must not be used until a suitable replacement is ob­tained. The colour of the correct re­placement cover is that of the coloured insert in the base of the plug, or the col­our that is embossed in words in the base of the plug (as applicable to the design of plug fitted).
The correct fuse rating of the replace­ment fuses that are ASTA approved to BS 1362 should be fitted. Replace­ment fuse covers may be purchased from your local electrical suppliers, or Miele Service Agent.
(The German standard version is sup­plied with a cable and moulded plug for connection to a 230 V single phase supply. It must only be connected via a fused 16 A socket).
76
Plumbing
Connection to the water inlet
Water in the dishwasher must not be used as drinking water.
The dishwasher may be connected to a cold or hot water supply, max. 60°C. Connection to a hot water supply would save energy costs and time. When connected to a hot water sup­ply all programme stages which would otherwise be carried out with cold water (pre-wash and interim rinse) as well as the PRE-WASH pro­gramme will be carried out with hot water.
The inlet hose is approx. 1.5 m long; a longer hose (4 m) may be bought from the Miele Spare Parts Dept.
A stopcock with a 3/4" male thread must be provided on site.
Plumbing
The water inlet hose must not be shortened or damaged in any way (see illustration).
Connect the inlet hose with the “Water­proof-System” preferably vertically (use an angle connector if necessary).
The dishwasher is constructed to comply with DVGW regulations, and may be connected to a suitable sup­ply without an extra non-return valve provided that national regulations allow this.
The water pressure (flow rate at the take-off point) must be between 1.0 and 10 bar pressure. If the water pressure is too low the in­dicator lights “Wash/Rinse”, “Drying” and “End” flash (see Problem Solv­ing Guide). If the water pressure is too high, a pressure reducer valve must be fitted.
If this is not possible, it can be in­stalled horizontally, but it is essen- tial that the main body of the “Water­proof valve” box is above the hose exit (see illustration). The ’lightning’ power symbol should be above the water flow ’arrow’.
77
Plumbing
There must be a distance of at least 20 cm between the floor and
the bottom of the “Waterproof valve” box, for either vertical or horizontal installation.
If the stopcock is situated in the worktop, a special angle connector can be ordered from the Miele Spare Parts Dept. (Part No. 2078910).
Lay the hose in such a way that it does not rise above the bottom of the “Waterproof valve” box (see illus­tration).
78
Plumbing
Drainage
The machine drainage system is fitted with a non-return valve, which prevents dirty water from flowing back into the machine via the drain hose.
The dishwasher is supplied with ap­prox. 1.5 m of flexible drain hose with an internal diameter of 22 mm.
The drain hose can be extended using a connection piece and an extra drain hose, (up to max. 4 metres).
The connection socket on the dish­washer can be turned. The hose can thus be laid to the right or left without needing to loosen the hose clip.
If the hose is to be directly fitted to the drainage outlet on site, use the hose clip supplied.
The on-site water pipe connection for the drain hose may be designed to fit more than one diameter of hose. The connection socket must be shortened if it juts too far into the drain hose. Otherwise the drain hose can become blocked.
Venting the drainage system
Open the dishwasher door fully.
If the site drain connection is situated lower than the guide path for the bot­tom basket rollers in the open door the drainage system must be vented. Otherwise a siphoning effect during a programme can cause the machine to empty itself of water.
To vent:
Cut off the top of the vent valve in the wash cabinet.
The drain system must not exceed 4 metres. The drain pump has a maximum delivery head of 1 metre.
The drain hose must not be short­ened.
79
Technical Data
Technical Data
Dishwasher model * G 6XX G 8XX
Height Freestanding 85 cm
(adjustable + 1.0 cm)
Height U- and i-models 82 cm
(adjustable+ 5.0 cm) Width 59.8 cm 59.8 cm Width of building in recess 60 cm 60 cm Depth 60 cm
(Freestanding model)
57 cm
(U- and i-models) Depth with door open 118.5 cm
(Freestanding model)
115.5 cm
(U- and i-models) Weight approx. 56 kg
(Freestanding model)
approx. 52 kg
(U- and i-models) Voltage Rated load
Fuse rating
see data plate
}
84 cm (adjustable + 5.0 cm)
57 cm (U- and i-models)
120.5 cm (U- and i-models)
approx. 57 kg (U- and i-models)
Test marks VDE, Radio and
Television suppressed Water pressure (flow rate) 1.0 - 10 bar pressure 1.0 - 10 bar pressure Hot water connection max. 60 °C max. 60 °C Delivery head max. 1 m max. 1 m Drainage length max. 4 m max. 4 m Connection cable ca. 1.7 m ca. 1.7 m Capacity 12 place settings 14 place settings
* see data plate for model number
808182
VDE, Radio and Television suppressed
83
Alteration rights reserved (G676/G677/G678/G876/G877/G878) /000 4697
This paper consists of cellulose which has been bleached without use of chlorine.
Loading...