To avoid the risk of accidents or
damage to the appliance, it is
essential to read these instructions
before it is installed and used for the
first time.
en-GB
M.-Nr. 07 927 000
Contents
Guide to the appliance .............................................4
Caring for the environment..........................................5
Warning and Safety instructions .....................................6
How to save energy ...............................................11
Switching on and off ..............................................12
Adjusting the door hinges .........................................36
Changing the door hinging .........................................37
Appliance door ...................................................37
Building in the appliance ..........................................40
Weight of the furniture door ..........................................40
Building into a peninsular run ........................................40
Fitting a furniture door ..............................................44
3
Guide to the appliance
a Safety lock indicator light
b On/Off button
c Temperature display
d Temperature selector buttons
(+ for warmer; – for colder)
e Super freeze button and indicator
light
f Alarm off button
a Frost free system
b Freezer tray
4
c Freezer drawers with
freezer calendar
Caring for the environment
Disposal of the packing
material
The transport and protective packing
has been selected from materials which
are environmentally friendly for
disposal, and should be recycled.
Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation!
Disposal of your old appliance
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly,
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of it
with your household waste.
Please dispose of it at your local
community waste collection / recycling
centre or contact your dealer for
advice. Ensure that it presents no
danger to children while being stored
for disposal.
Take care not to damage the pipework
at the back of it before or during
transportation to an authorised
collection depot.
In this way, refrigerant in the pipework
and oil in the compressor will be
contained and will not leak out into the
environment.
5
Warning and Safety instructions
Any other usage is not supported by
This appliance complies with all
relevant legal safety requirements.
Improper use can, however, present
a risk of both personal injury and
material damage.
To avoid the risk of accidents and
damage to the appliance, please
read these instructions carefully
before installation and before using
it for the first time. They contain
important notes on the installation,
safety, operation and care of the
appliance.
the manufacturer and could be
dangerous. Miele cannot be held liable
for damage resulting from incorrect or
improper use or operation of the
appliance.
This appliance is not intended for
~
use by people with reduced physical,
sensory or mental capabilities, or lack
of experience and knowledge, unless
they are supervised whilst using it, or
have been shown how to use it
correctly by a person responsible for
their safety.
Keep these instructions in a safe
place and pass them on to any
future user.
Correct application
This appliance is not designed for
~
commercial use. It is intended for use in
domestic households and in similar
working and residential environments
such as:
–
Shops
–
Offices and showrooms
and by residents in establishments
such as
–
Hostels and guest houses.
It must only be used as a domestic
appliance to store deep frozen food, to
freeze fresh food and to prepare ice.
Safety with children
This appliance is not a toy! To avoid
~
the risk or injury, do not allow children
to play on or near it, or to play with the
controls. Please supervise young
children whilst you are using it. Older
children may only use the appliance if
its operation has been clearly explained
to them and they are able to use it
safely, recognising the dangers of
misuse.
6
Warning and Safety instructions
Technical safety
Before setting up the appliance,
~
check it for any externally visible
damage. Do not install and use a
damaged appliance.
If the connection cable is faulty it
~
must only be replaced by a service
technician authorised by the
manufacturer to protect the user from
danger.
This appliance contains the coolant
~
Isobutane (R600a), a natural gas which
is environmentally friendly. Although it
is flammable, it does not damage the
ozone layer and does not increase the
greenhouse effect. The use of this
coolant has, however, led to a slight
increase in the noise level of the
appliance. In addition to the noise of
the compressor, you might be able to
hear the coolant flowing around the
system. This is unavoidable, but does
not have any adverse effect on the
performance of the appliance.
Care must be taken during the
transportation and setting up of the
appliance that no parts of the cooling
system are damaged. Leaking coolant
can damage the eyes.
In the event of any damage:
- avoid naked flames and anything
which creates a spark,
- disconnect from the mains,
- air the room in which the appliance is
located for several minutes and
- contact the Service Department for
advice.
room, there is the danger of
combustible gases building up.
For every8gofcoolant at least 1 m
room space is required. The amount of
coolant in the appliance is stated on the
data plate inside the appliance.
Safe operation of the appliance is
~
only assured if it has been installed and
connected in accordance with these
operating and installation instructions.
Before connecting the appliance to
~
the mains supply, make sure that the
rating on the data plate corresponds to
the voltage and frequency of the
household supply.
This data must correspond in order to
avoid the risk of damage to the
appliance. Consult a qualified
electrician if in any doubt.
Do not connect the appliance to the
~
mains electricity supply by a
multi-socket unit or an extension lead.
These do not guarantee the required
safety of the appliance (e.g. danger of
overheating).
3
of
The more coolant there is in an
~
appliance, the larger the room it should
be installed in. In the event of a
leakage, if the appliance is in a small
7
Warning and Safety instructions
The electrical safety of this
~
appliance can only be guaranteed
when continuity is complete between it
and an effective earthing system which
complies with current local and national
safety regulations. It is most important
that this basic safety requirement is
present and tested regularly, and
where there is any doubt, the
household wiring system should be
inspected by a qualified electrician.
The manufacturer cannot be held liable
for damage or injury caused by the lack
of or inadequacy of an effective
earthing system (e.g. electric shock).
Installation, maintenance and
~
repairs may only be carried out by a
suitably qualified and competent
person in strict accordance with current
national and local safety regulations.
Repairs and other work by unqualified
persons could be dangerous. The
manufacturer cannot be held liable for
unauthorised work.
While the appliance is under
~
guarantee, repairs should only be
undertaken by a service technician
authorised by the manufacturer.
Otherwise the guarantee will be
invalidated.
The appliance must be isolated from
~
the electricity supply during installation,
maintenance and repair work.
The appliance is only completely
isolated from the electricity supply
when:
it has been switched off at the wall
–
socket and the plug has been
withdrawn.
the fuse from the fused spur
–
connection unit has been withdrawn,
or
the mains fuse is withdrawn, or the
–
screw-out fuse is removed (in
countries where this is applicable).
Faulty components must only be
~
replaced by genuine Miele original
spare parts. The manufacturer can only
guarantee the safety of the appliance
when Miele replacement parts are
used.
This equipment may only be used in
~
mobile installations such as ships if a
risk assessment of the installation has
been carried out by a suitably qualified
engineer.
In countries where there are areas
~
which may be subject to infestation by
cockroaches or other vermin, pay
particular attention to keeping the
appliance and its surroundings in a
clean condition at all times. Any
damage which may be caused by
cockroaches or other vermin will not be
covered by the guarantee.
8
Warning and Safety instructions
Correct use
Never handle frozen food with wet
~
hands. Your hands may freeze to the
frozen food.
Do not take ice cubes out with your
~
bare hands and never place ice cubes
or ice lollies in your mouth straight from
the freezer. The very low temperature of
the frozen ice or lollies can cause frost
burn to the lips and tongue.
Do not refreeze thawed or partially
~
thawed food.
Defrosted food should be used up as
quickly as possible, as food soon loses
it nutritional value and goes off.
Defrosted food may only be re-frozen
after it has been cooked.
Never store explosive materials in
~
the appliance or any products
containing propellants (e.g. spray
cans). Thermostats switching on may
produce sparks which could present a
fire hazard. Flammable compounds
could explode.
Do not operate any electrical
~
equipment (e.g. an electric ice-cream
maker) inside the appliance. Danger of
sparking and explosion.
Do not store cans or bottles
~
containing carbonated drinks or liquids
which could freeze in the freezer. The
cans or bottles could explode.
Danger of injury and damage to the
appliance.
When cooling drinks quickly in the
~
freezer, make sure bottles are not left in
for more than one hour, otherwise they
could burst, resulting in injury or
damage.
Observe the "use by" dates given on
~
food to avoid the risk of food poisoning.
Storage times will depend on several
factors, including the freshness and
quality of the food as well as the
temperature at which it is stored. Follow
the instructions given on food
manufacturer's packaging on storage
conditions required, as well as the “use
by” date.
Do not use sharp edged objects to
~
– remove frost and ice,
– separate frozen foods or remove ice
trays.
They will damage the evaporator,
causing irreversible damage to the
appliance.
Never place electric heaters or
~
candles in the appliance to defrost it.
These can damage the plastic parts.
Do not use defrosting sprays or
~
de-icers, as they might contain
substances which could damage the
plastic parts or which could cause a
build-up of gases and pose a danger to
health.
Do not use any oils or grease on the
~
door seal, as these will cause the seal
to deteriorate and become porous with
time.
9
Warning and Safety instructions
Do not block the ventilation gaps in
~
the plinth or the top of the appliance
housing unit as this would impair the
efficiency of the appliance, increase the
electricity consumption and could
cause damage to the appliance.
The appliance is designed for use
~
within certain climate ranges (ambient
temperatures), and should not be used
outside this range. The climate range
for your appliance is stated on the data
plate inside the appliance.
Installing it in a room with too low an
ambient temperature, e.g. a garage,
can lead to the appliance switching off
for longer periods so that it cannot
maintain the required temperature.
Do not use a steam-cleaning
~
appliance to defrost or clean this
appliance. Steam could reach the
electrical components and cause a
short circuit.
Disposal of your old freezer
Before disposing of an old
~
appliance, first make the door latch or
lock unusable.
This way you will prevent children from
accidentally locking themselves in and
endangering their lives.
Be careful not to damage any part of
~
the pipework whilst awaiting disposal,
e.g. by
puncturing the refrigerant channels
–
int he evaporator, e.g. by
bending any pipework.
–
– scratching the surface coating.
Splashes of refrigerant can damage the
eyes.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
10
How to save energy
Normal energy
consumption
Installation siteIn a ventilated room.In an enclosed, unventilated room.
Protected from direct sunlight.In direct sunlight.
Not near to a heat source (radiator,
oven).
Where the ideal ambient room
temperature is approx. 20°C.
Do not cover the ventilation gaps
and dust them regularly.
Temperature setting
with a thermostat
which is approximate
(set in stages).
Temperature setting
with a thermostat which
is exact to the degree
(digital display).
UseDrawers, shelves and racks
DefrostingDefrost the freezer section when a
With a medium setting of 2 to 3.With a high setting: the lower the
Larder section 8 to 12 °C
Refrigerator section 4 to 5 °C
PerfectFresh zone just above 0 °C
Freezer section -18 °C
Wine storage section 10 to 12 °C
arranged as they were when the
appliance was delivered.
Only open the door when necessary
and for as short a time as possible.
Store food in an organised way.Searching for an item will mean the
Allow hot food and drinks to cool
down before placing them in the
appliance.
Store food covered or packaged.The evaporation or condensation of
Place frozen food in the refrigerator
to defrost.
Do not over-fill the appliance to
allow air to circulate.
layer of ice 0.5 cm thick has built
up.
Increased energy
consumption
Near to a heat source (radiator,
oven).
Where there is a high ambient room
temperature.
temperature in the compartment, the
higher the energy consumption.
On appliances with winter setting,
please make sure that the winter
setting is switched off when the
ambient temperature is warmer than
16 °C .
Frequent opening of the door for
long periods will cause a loss of
coldness.
door is open for longer.
Hot food will cause the refrigerator
unit to run for a long time, as the
appliance will have to work harder
to reduce the temperature.
liquids will cause a loss of coldness
in the refrigerator.
A layer of ice hinders the cold from
reaching the frozen food, and
increases energy consumption.
11
Switching on and off
Before using for the first time
Important:
To ensure the correct functioning of
the appliance, let it stand for
between 1½ and 2 hours after
transporting it to its final location
before connecting it to the mains.
Cleaning
Clean the inside of the appliance and
^
the accessories with lukewarm water
and a little washing-up liquid, and
then dry with a soft cloth.
Switching on
^ Press the On/Off button.
The temperature display lights up and
the appliance starts cooling.
The cooling system is switched off. (If
this does not happen, the safety lock is
still activated).
Safety lock
The safety lock can be activated to
prevent the appliance being switched
off inadvertently.
Activating or de-activating the safety
lock
^ Press and hold the Super freeze
button for approx. 5 seconds.
The Super freeze indicator light flashes,
and
; flashes in the temperature
display.
To enable the temperature to get
sufficiently cold inside the appliance,
allow the appliance to run for a few
hours before placing food in it.
Cool pack
Place the cool pack in the top freezer
drawer or to save space on the freezer
tray. The cool pack will be at its most
effective after it has been in the freezer
for approx. 24 hours.
Switching off
^
Press the On/Off button until the
temperature display goes out.
12
^
Then press the Super freeze button
again.
; will light up in the display.
^
You can now choose between
and
; 1 by pressing the temperature
selector buttons:
0: the safety lock is de-activated,
1: the safety lock is activated.
^
Press the Super freeze button to save
the setting.
The safety lock indicator light
light up when the safety lock has been
activated.
; 0
X will
Press the On/Off button to come out
^
of the setting mode.
If you do not do this, the electronics will
switch over to normal operation
automatically after a couple of minutes.
Switching off for longer
periods of time
If the appliance is not going to be used
for a longer period of time, e.g. whilst
on holiday:
^ switch the appliance off,
^ disconnect it from the mains. Switch
off at the wall and withdraw the plug
from the socket, or disconnect the
mains fuse or remove the screw-out
fuse in countries where this is
applicable.
Switching on and off
^
clean the appliance out and
^
leave the door ajar to air the
appliance.
If, during a long absence, the
appliance is switched off but not
cleaned out and the door is left shut,
there is a danger of mould and
odours building up inside the
appliance.
13
The correct temperature
It is very important to set the correct
temperature for storing food in the
appliance. Micro-organisms will cause
food which is not stored at the correct
temperature to deteriorate rapidly.
Temperature influences the growth rate
of these micro-organisms. Reducing
the temperature reduces their growth
rate.
To freeze fresh food and to store frozen
food for a long time, a temperature of
-18 °C is required. At this temperature
the growth of micro-organisms is
generally halted. As soon as the
temperature rises above -10 °C, the
micro-organisms become active in the
food again so that it cannot be kept as
long. For this reason, partially defrosted
or defrosted food must not be re-frozen.
Food may be re-frozen once it has
been cooked, as the high temperatures
achieved when cooking destroy most
micro-organisms.
The temperature in the appliance will
rise:
–
the more often the door is opened
and the longer it is kept open,
–
if too much food is stored in it at
once,
–
the warmer the food is which is being
put into it,
Setting the temperature
Use the two buttons underneath the
temperature display to set the
temperature for the freezer.
Press the
+ button: to raise the temperature
(it gets warmer)
– button: to reduce the temperature
(it gets cooler).
The temperature being set will flash in
the display.
When pressing the buttons, the
following information shows in the
display:
– When first pressed, the last
temperature selected flashes.
– Each subsequent press of the button
adjusts the temperature shown in
1 °C steps.
–
Keeping the button pressed in
adjusts the temperature continually.
Approx. 5 seconds after letting go of
the button, the current actual
temperature of the freezer section is
automatically shown.
–
the higher the ambient temperature
surrounding the appliance.
The appliance is designed for use in
specific ambient temperatures
(climate ranges). Do not use in
ambient temperatures for which it is
not designed.
14
The correct temperature
If you have adjusted the temperature,
wait for approx. 6 hours if the
appliance is not very full and for
approx. 24 hours if the appliance is
full before checking the temperature
display as it will take this long for the
display to give an accurate reading. If,
after this time, the temperature is still too
high or too low, you will need to adjust it
again.
Temperature range
The temperature can be adjusted from:
-14 °C to -28 °C
The ambient temperature in the room
and the installation location can affect
the time it takes for the appliance to
reach the lowest temperature. If the
ambient temperature is too high, the
appliance may not reach the lowest
temperature.
Temperature display
During normal operation, the
temperature display on the control
panel shows the temperature in the
warmest part of the appliance.
This loss of coldness is no cause for
concern in the following circumstances:
when the door has been left open for
–
a while, e.g. for removing or storing a
large amount of food,
when fresh food is being frozen.
–
However, if the temperature in the
freezer section remains above -18 °C
for a long time, check that the frozen
food has not started to defrost. If it has
started thawing, check that the food is
safe to use and if it is, use it as quickly
as possible.
Temperature display brightness
The appliance is supplied with the
brightness of the temperature display
set as low as possible. However, if the
door is opened, a setting changed or if
the alarm is sounding, the temperature
display will appear much brighter.
The level of brightness can be
adjusted:
If the temperature is not within the
range that the appliance is able to
display (below 0 °C), bars will flash in
the temperature display.
The temperature display will flash if
–
a different temperature is being set,
–
the temperature in the appliance has
risen by several degrees, indicating
that the appliance is warming up too
much.
^
Press and hold the Super freeze
button for approx. 5 seconds.
The Super freeze indicator light flashes
and a
; flashes in the temperature
display.
15
Loading...
+ 33 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.