Operating and Installation
Instructions
Ventilation System
DA 5341 D
To prevent accidents
and machine damage,
read these instructions
before
installation or use.
en - US, CA
M.-Nr. 07 262 380
Contents
IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Guide to the hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Turning on the fan .................................................10
Selecting the power level............................................10
Delayed Shut Down ................................................12
Turning off the fan .................................................12
Turning the lighting on/off ...........................................13
Dimming the lighting ...............................................13
Grease filter timer .................................................14
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Cleaning the casing................................................16
Grease filters .....................................................17
Changing the light bulbs ............................................19
After Sales Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Caring for the environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Appliance dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Structural support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Installation accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Air extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Electrical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
2
IMPORTANT SAFETY INSTRUCTIONS
Read these Operating Instructions carefully before installing or
using the Ventilation System.
This appliance is designed to vent
This appliance is intended for
residential use only. Use the
appliance only for its intended
purpose. The manufacturer cannot
be held responsible for damages
caused by improper use of the
hood.
This appliance complies with current
safety requirements. Improper use
of the appliance can lead to
personal injury and material
damage.
READ AND SAVE THESE
INSTRUCTIONS
CAUTION
For General Ventilating Use Only.
Do not use to exhaust hazardous or
explosive materials and vapors.
~
cooking smoke and odors only.
Be certain your appliance is
~
properly installed and grounded by a
qualified technician.
To guarantee the electrical safety of this
appliance, continuity must exist
between the appliance and an effective
grounding system. It is imperative that
this basic safety requirement be met. If
there is any doubt, have the electrical
system of the house checked by a
qualified electrician. The manufacturer
cannot be held responsible for
damages caused by the lack, or
inadequacy, of an effective grounding
system.
Before connecting the appliance to
~
the power supply make sure that the
voltage and frequency listed on the
data plate correspond with the
household electrical supply. This data
must correspond to prevent machine
damage. If in doubt consult a qualified
electrician.
Installation work and repairs should
~
only be performed by a qualified
technician in accordance with all
applicable codes and standards.
Repairs and other work by unqualified
persons could be dangerous and the
manufacturer will not be held
responsible.
3
IMPORTANT SAFETY INSTRUCTIONS
This equipment is not designed for
~
maritime use or for use in mobile
installations such as recreational
vehicles or aircraft. However, under
certain conditions it may be possible for
an installation in these applications.
Please contact the nearest Miele dealer
or the Miele Technical Service
Department with specific requirements.
WARNING - TO REDUCE THE RISK
OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
Use this unit only in the manner
~
intended by the manufacturer. If you
have questions, contact the
manufacturer.
Before servicing or cleaning the unit,
~
switch power off at the service panel
and lock the service disconnecting
means to prevent power from being
switched on accidentally. If the service
disconnecting means cannot be
locked, securely fasten a prominent
warning device, such as a tag, to the
service panel.
Before discarding an old appliance,
~
disconnect it from the power supply
and remove the power cord to prevent
hazards.
Use
Do not allow children to play with or
~
operate the appliance or its controls.
Supervise its use by the elderly or
infirm.
Do not flambé or grill with an open
~
flame beneath the hood.
Flames could be drawn up into the
hood by the suction and the grease
filters may catch fire.
Never operate gas burners without
~
cookware. Turn the burner off when not
in use. Adjust the burner so that the
flames do not extend beneath the
cookware. Do not overheat the
cookware, e.g. when using a wok. The
hood can be damaged due to
excessive heat from the burners and
the cookware.
Do not use the hood without the
~
grease filter in place.
Clean the grease filter regularly.
~
Dirty filters are a fire hazard.
Do not use a steam cleaner to clean
~
the hood. Steam could penetrate
electrical components and cause a
short circuit.
Always turn on the hood when using
~
the cooktop to prevent damage from
condensation.
4
IMPORTANT SAFETY INSTRUCTIONS
, WARNING - TO REDUCE
THE RISK OF A COOKTOP
GREASE FIRE:
Never leave surface units
~
unattended at high settings. Boilovers
cause smoking and greasy spillovers
may ignite. Heat oils slowly on low or
medium settings.
Always turn the hood on when
~
cooking at high heat.
Clean ventilating fans frequently.
~
Grease should not be allowed to
accumulate on fan or filter.
Use proper pan size. Always use
~
cookware appropriate for the size of the
surface element.
, WARNING
TO REDUCE THE RISK OF INJURY
TO PERSONS, IN THE EVENT OF A
COOKTOP GREASE FIRE, OBSERVE
THE FOLLOWING:
SMOTHER FLAMES with a close
~
fitting lid, cookie sheet, or metal tray
then turn off the burner.
BE CAREFUL TO PREVENT BURNS.
If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE
DEPARTMENT.
NEVER PICK UP A FLAMING PAN
~
- You may be burned.
DO NOT USE WATER, including
~
wet dishcloths or towels - a violent
steam explosion will result.
Use a fire extinguisher
~
ONLY if:
– You have a class ABC extinguisher,
and you know how to operate it.
– The fire is small and contained in the
area where it started.
–
The fire department is being called.
–
You can fight the fire with your back
to an exit.
5
IMPORTANT SAFETY INSTRUCTIONS
Installation
, WARNING
~
To reduce the risk of fire only use
metal ductwork.
Any fittings, sealant, or materials
~
used to install the ductwork must be
made of approved non-flammable
materials.
Provided a larger distance is not
~
given by the manufacturer of the
cooktop, follow the minimum safety
distances between a cooktop and the
bottom of the hood:
– 22" (550 mm) above electric
cooktops,
– 30" (762 mm) above gas cooktops,
– 26" (650 mm) above an open electric
grill or an open electric boiler/fryer.
If local building codes require a greater
safety distance, follow their
requirement.
If there is more than one appliance
beneath the hood and they have
different minimum safety distances
always select the greater distance.
Never connect an exhaust hood to
~
an active chimney, dryer vent, vent flue,
or room ventilating ductwork. Seek
professional advice before connecting
an exhaust hood vent to an existing,
inactive chimney or vent flue.
WARNING - TO REDUCE THE RISK
OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
Installation work and electrical
~
wiring must be done by qualified
person(s) in accordance with all
applicable codes and standards,
including fire-rated construction.
Sufficient air is needed for
~
combustion and exhausting of gases
through the flue (chimney of fuel
burning equipment to prevent back
drafting. Follow the heating equipment
manufacturer’s guideline and safety
standards such as those published by
the National Fire Protection Association
(NFPA) and the American Society for
Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE), and
the local code authorities.
Do not install this hood over
~
cooktops burning solid fuel.
Do not use an extension cord to
~
connect the appliance to electricity.
Extension cords do not guarantee the
required safety of the appliance,
(e.g. danger of overheating).
6
When cutting or drilling into wall or
~
ceiling, do not damage electrical wiring
and other hidden utilities.
Ducted fans must always be vented
~
to the outdoors.
The ventilation hood works by air
extraction. The air is drawn in and
cleaned by the grease filter and
directed outside.
The hood comes equipped with a
non-return flap in each chimney. This
flap automatically closes when the
hood is turned off so that no exchange
of outside air and room air can occur.
When the hood is turned on, the air
pressure of the exhaust fan
automatically opens the flap blowing
the inside air and cooking odors
outside.
Functional description
7
Guide to the hood
8
Guide to the hood
a Cover frame
b Chimney
c Canopy
d Overhead lighting
e Control panel
The two sides of the hood can be
operated independently of one another.
f Grease filters
g Light button
This button turns the light on and off
and also dims the light.
The lighting can be used independently
of the fan.
h On/Off button
k Grease filter button
The indicator next to the grease filter
button lights when the grease filter
needs to be cleaned.
This button is also used:
to reset the grease filter timer after
–
cleaning the grease filter (see
"Cleaning and Care").
to show how long the grease filter
–
has been in use (see "Operation /
Grease filter timer").
to change the number of hours
–
counted by the grease filter timer
(see "Operation / Reprogramming the
grease filter timer").
i Fan power level buttons
Four fan speed selection.
j Delayed Shut Down
This button activates the Delayed Shut
Down feature. The fan can be set to
turn off automatically after either 5 or
15 minutes.
9
Operation
The two sides of the hood can be
operated independently of one
another.
Turning on the fan
Press the On/Off button.
^
The hood turns on level 2 and the
indicator lights.
Automatically switching back the
intensive power level
The intensive level "4" can be
programmed to automatically switch
back to level "3" after 10 minutes.
Turn the fan and the lights off.
^
Press and hold the "Delay Shut down"
^
button for 10 secs. The first indicator
lights.
Selecting the power level
^ Use the "–/+" controls to select the
desired power level.
+ = increases the fan speed
– = decreases the fan speed
Levels "1" to "3" (green indicators) are
usually sufficient for normal cooking.
Intensive setting
Level "4" (yellow indicator) should be
used for a short period when frying or
cooking food with a strong aroma.
^ Press the following buttons one after
another,
– light
–
the "–" button, and
–
the light button again.
10
If the power level indicators "1" and "4"
flash, the automatic switch back is not
activated.
To activate the automatic switch back
^
press the "+" button.
The power level indicators "1" and "4"
light continuously.
To deactivate press the "–" button.
^
^ To save the setting press the "Delay
Shut Down" button.
If the procedure is not stored within
4 minutes of programming, the hood
will automatically default to the "old"
data.
Operation
Fan performance
The maximum air flow capacity of the
dual blower system is 1250 cfm
(625 x 2 cfm). Factors such as narrow
duct diameter and bends will affect this
value.
Level 1 operates at 40% capacity
Level 2 operates at 60% capacity
Level 3 operates at 80% capacity
Level 4 operates at 100% capacity
11
Operation
Delayed Shut Down
If odors or smoke remain in the kitchen
after cooking has been completed, the
Delayed Shut Down feature can be
selected to allow the hood to continue
running for either 5 or 15 minutes. After
that period of time the fan turns off
automatically.
Press the Delayed Shut Down button
^
while the fan is still running.
Press once = 5 minute delay
(left indicator lights)
Press twice = 15 minute delay
(right indicator lights)
To cancel the feature press the
Delayed Shut Down button again. The
fan will not turn off automatically.
Turning off the fan
Press the On/Off button to turn the
^
fan off.
The indicator goes out.
Automatic Safety Shut Off
The fan will turn off automatically
10 hours after the last button was
activated. The lighting however will
remain on.
^ Press the On/Off button to turn the
fan back on again.
12
Operation
Turning the lighting on/off
The overhead lighting can be turned on
and off independently of the fan.
Press the light button briefly to turn
^
on the lighting.
The light button indicator illuminates.
Press the light button briefly again to
^
turn off the lighting.
The light button indicator will go out.
Dimming the lighting
The brightness of the lighting can be
adjusted.
While the lighting is turned on, press
^
and hold the light button.
The lighting will dim until the button is
released.
If the button is pressed again, the
^
lighting will brighten until the button is
released.
If the button is pressed continuously,
the light will cycle between bright and
dark.
^ Press the light button again to turn off
the lighting.
13
Operation
Grease filter timer
A timer monitors the hours of fan
operation. The indicator for the grease
filter will light after 30 hours of operation
or the preselected time. The grease
filters must then be cleaned. See
"Cleaning and care / Grease Filter".
After the grease filters have been
cleaned and put back in place, the
grease filter timer must be reset.
^ To do this, press the grease filter
button for about 3 seconds while the
fan is running.
The indicator will go out.
Checking the grease filter timer
To check the percentage of time
already used:
Press the On/Off button to turn the
^
fan on.
^ Press the grease filter button.
The indicator lights.
The number of flashing "–/+" indicators
show the percentage of programmed
hours that have been used.
14
1 indicator = 25 %
2 indicators = 50 %
3 indicators = 75 %
4 indicators = 100 %
This information will remain stored in
memory in the event of a power failure.
Reprogramming the grease filter
timer
The grease filter timer is preset to
30 hours. This time can be lengthened
or shortened to 20, 30, 40 or 50 hours.
A time of 20 hours should be
–
programmed in kitchens with
frequent pan or deep frying.
A time of 20 hours should also be
–
programmed if the kitchen is only
used occasionally to prevent grease
which has accumulated over a long
period of time from hardening on the
filter, making cleaning more difficult.
Operation
The lit "–/+" indicator shows the
programmed time:
1st indicator from the left = 20 hours
2nd indicator from the left = 30 hours
3rd indicator from the left = 40 hours
4th indicator from the left = 50 hours
Use the "–/+" button to select the
^
desired time.
^ Store the selection by pressing the
grease filter button.
^ Press the On/Off button to turn off the
fan.
^
Press the Delayed Shut Down and
grease filter button at the same time.
The indicator for the grease filter timer
and one of the "–/+" indicators will flash.
If the procedure is not stored within
4 minutes of programming the hood
will automatically default to the "old"
data.
15
Cleaning and care
Before cleaning or servicing the
hood, disconnect it from the power
supply by either removing the fuse,
unplugging it from the outlet or
manually "tripping" the circuit
breaker.
Cleaning the casing
Never use on the hood:
,
- cleaning agents containing soda,
acids, chlorides or thinners,
- abrasive cleaning agents
e.g. powder or cream cleansers,
- steel wool or abrasive sponges,
e.g. pot scourers or sponges which
have been previously used with
abrasive cleaning agents,
Stainless steel
Stainless steel surfaces can be cleaned
using a non-abrasive stainless steel
cleaner.
To help prevent resoiling, a conditioner
for stainless steel can also be used.
Apply sparingly with even pressure.
Stainless steel colored controls
These controls may become dis
colored or damaged if not cleaned
regularly.
Do not use a stainless steel cleaner
on these controls.
-
- limescale removers,
- caustic (oven) cleaners.
They will damage the surface.
^
The exterior surfaces and controls
can be cleaned with warm water and
liquid dish soap applied with a soft
sponge.
^
Wipe dry using a soft cloth.
Only use a slightly damp sponge
when cleaning the controls. Water
could penetrate into the electronics
and cause damage.
^
Glass surfaces can be cleaned using
glass cleaner.
16
Cleaning and care
Grease filters
The reusable metal grease filters
remove solid particles from the vented
kitchen air (grease, dust, etc).
The grease filters should be cleaned
every3-4weeks or whenever the
grease filter indicator lights.
Keep the grease filters clean to
prevent a fire hazard.
Removing the grease filter
To remove the grease filters pull the
^
locking clip forward. Lower the filter
45° unhook it at the rear and take it
out. Support the grease filter so that it
does not fall onto the cooktop.
17
Cleaning and care
Cleaning the grease filters
By hand: use a scrub brush with a
^
solution of warm water and mild
detergent.
Do not use the pure detergent,
aggressive all purpose cleaners,
oven sprays, abrasive cleaning
agents or limescale removers. They
could destroy the filter.
In a dishwasher: place the filter
^
vertically in the lower basket, making
sure that the spray arm is not
blocked.
Use a hot temperature program,
e.g. "Heavy Soil" or "Pots and pans".
Use the recommended amount of
dishwasher detergent. Overuse could
destroy the filter.
If the filter is incorrectly installed,
^
insert a small screwdriver into the slit
along its edge to disengage it from
the casing.
After cleaning and returning the grease
filters the timer must be reset.
Depending on the detergent,
cleaning the grease filter in a
dishwasher may cause permanent
discoloration of the filter surface.
Performance of the filter will not be
affected by this discoloration.
^
After cleaning, the filters can be
placed on a towel to air dry.
^
While the filters are removed, clean
any dirt or grease from the interior
casing to prevent the risk of fire.
^
When putting the grease filter back
make sure that the locking clip is
facing the cooking surface.
18
^ While the fan is on, press and hold
the grease filter control until only the
first "-/+" indicator is flashing.
^ The second grease filters must also
be reset in the same way, even if the
timer has not yet reached its
maximum.
Changing the light bulbs
Disconnect the exhaust hood from
the power supply by either shutting
off the main breaker or completely
removing the fuse.
Note: The appliance has 2 electrical
connections, each must be
disconnected from the main power
supply.
When in use halogen bulbs become
extremely hot, and can burn your
hands. Do not attempt to change the
bulbs until they have had sufficient
time to cool.
Do not touch the bulb surface.
Fingerprints or body oils deposited
on the bulb will decrease its life.
Please follow the manufacturer’s
instructions.
Cleaning and care
^ To change the halogen bulb, first
gently press the light cover. The
cover will open and can now be
flipped down.
^
Pull the halogen bulb from its socket,
then insert a new bulb.
^
Flip the light cover back up, making
sure it clicks into place.
19
After Sales Service
Repairs
In the event of a fault which you cannot
easily fix yourself, please contact the
Miele Technical Service Department.
When contacting the Technical
^
Service Department, please quote
the model and serial number of your
appliance.
These are shown on the data plate
which is visible when the grease filters
are removed.
MieleCare
(USA only)
MieleCare, our Extended Service
Contract program, gives you the
assurance of knowing that your
appliance investment is covered by
5 years of worry free ownership.
MieleCare is the only Extended Service
Contract in the industry that guarantees
repairs by a Miele Authorized Service
Provider using genuine Miele parts.
Only genuine Miele parts installed by
factory trained professionals can
guarantee the safety, reliability, and
longevity of your Miele appliance.
Please note that unless expressly
approved in writing by Miele’s Service
department, Extended Service
Contracts offered by other providers for
Miele products will not be recognized
by Miele. Our goal is to prevent
unauthorized (and untrained) service
personnel from working on your Miele
products, possibly doing further
damage to them, you and/or your
home.
20
To learn more about MieleCare
Extended Service Contracts, please
contact your appliance dealer or visit
us online at:
http://store.miele.com
Installation Instructions
22
Caring for the environment
Disposal of packing material
The cardboard box and packing
materials protect the appliance during
shipping. They have been designed to
be biodegradable and recyclable.
Please recycle.
To prevent suffocation of children,
ensure that any plastic wrappings,
bags, etc. are disposed of safely
and kept out of their reach.
Disposal of an old appliance
Old appliances may contain materials
that can be recycled. Please contact
your local recycling center about the
possibility of recycling these materials.
Before discarding an old hood,
unplug it from the outlet and cut off
its power cord to prevent hazards.
23
Appliance dimensions
Exhaust connection2x6"(2x150mm)diameter
1) Opening for ductwork and power cord
24
Do not install this exhaust hood over
cooktops burning solid fuel.
Provided a larger distance is not
given by the manufacturer of the
cooktop, follow the minimum safety
distances between a cooktop and
the bottom of the hood:
22" (550 mm) above electric
cooktops,
30" (762 mm) above gas cooktops,
26" (650 mm) above an open
electric grill or an open electric
boiler/fryer.
If there is more than one appliance
beneath the hood and they have
different minimum safety distances
always select the greater distance.
Installation
Observe local building codes.
See "Important Safety Instructions"
for further information.
CAUTION:
During the installation process,
please be careful of sharp edges
that can cause harm.
25
Structural support
The ceiling mounting plate will
support the weight of the hood. This
ceiling plate must be attached to
rigid structural framing that is
supported in its entirety by the
ceiling joists, or to the ceiling joists
directly. Do not attach the plate
directly to the ceiling with anchors,
toggle bolts, etc.
26
Installation instructions
See the enclosed installation
^
instruction sheet.
Please read the "Important Safety
^
Instructions" and Installation
instructions before installing this
hood.
Installation accessories
Installation accessories
8 leveling plates
for correcting an uneven ceiling.
8 Screws8x60mmwith 8 Washers
for securing the ceiling plate.
(S8 wall anchors included in the
packaging are not for use in USA)
4 ScrewsM4x8mm
for adjusting the chimney.
2 exhaust connectors
2 hose clips for securing the ducting.
27
Air extraction
WARNING
,
Danger of toxic fumes.
Exhaust ducting and connections
The ducting should be as short and
–
straight as possible, and the number
of sharp bends should be minimized.
Gas cooking appliances release
carbon monoxide that can be
harmful or fatal if inhaled.
The exhaust gases extracted by
the hood should be vented
outside of the building only.
Do not vent exhaust air into
spaces within walls or ceilings or
in attics, crawl spaces, or garages
To reduce the risk of fire, only use
metal ductwork.
Please read and follow the
"IMPORTANT SAFETY
INSTRUCTIONS" to reduce the risk of
personal injury. Follow all local building
codes when installing the hood.
For most efficient air extraction, the
–
diameter of the ductwork should not
be less than 6" (150 mm). Use of flat
ducts also reduces the air extraction
efficiency.
Noise levels of the hood will increase
–
if flat ducts or round ducts of less
than 6" (150 mm) in diameter are
used.
– Use smooth or flexible pipes made
from approved non-flammable
materials for exhaust ducting.
– Where the ductwork is horizontal, it
must slope away from the hood at
1
least
/8" per foot (1 cm per meter) to
prevent condensation dripping into
the appliance.
– If the exhaust is ducted through an
outside wall, a Miele Telescopic Wall
Vent can be used.
28
– If the exhaust is ducted into an
inactive flue, the air must be expelled
parallel to the flow direction of the
flue.
Never connect an exhaust hood to
an active chimney, dryer vent, flue,
or room venting ductwork. Seek
professional advice before
connecting an exhaust hood vent to
an existing, inactive chimney or vent
flue.
Important
Air extraction
Condensate trap
optional accessory
In some cases, a 2 condensate traps
may be required to collect and
evaporate any condensation which may
develop. This optional accessory is
available for ducts 5" (125 mm) and
7
5
/8" (150 mm) in diameter.
^ When installing the condensate traps,
ensure that they are positioned
vertically and if possible directly
above the exhaust outlet.
If the ductwork runs through rooms,
ceilings, garages, etc. where
temperature variations exist, it may
need to be insulated to reduce
condensation.
29
Electrical data
All electrical work should be
performed by a qualified electrician
in strict accordance with national
and local safety regulations.
Installation, repairs and other work
by unqualified persons could be
dangerous. The manufacturer can
not be held responsible for
unauthorized work.
Ensure that power to the appliance
is OFF while installation or repair
work is performed.
Verify that the voltage, load and
^
circuit rating information found on the
data plate (located behind the
grease filter), match the household
electrical supply before installing the
hood.
^ This appliance requires two electrical
mains cables. Each one must be
connected via a suitable isolator
which complies with local and
national safety regulations. Their
on/off switches must be easily
accessible after the appliance has
been built in.
Important
To increase security before the
machine is installed, it is
recommended to install a protective
switch (30 mA).
Important
The hood must be hard wired
accordingly:
Black/Red wire:....connect to L1 (live)
White wire: .....connect to N (neutral)
Green wire: . . connect to GND (ground)
Maximum load ...............820W
Fan....................2x350W
Lighting .................6x20W
Voltage .....................120V
Frequency ..................60Hz
Circuit rating..................15A
If there is any question concerning the
electrical connection of this appliance
to your power supply, please consult a
licensed electrician or call Miele’s
Technical Service Department. See
back cover for contact information.
WARNING:
THIS APPLIANCE MUST BE
GROUNDED
30
31
Alteration rights reserved / 0908
For the most updated manual see the Miele web site.
M.-Nr. 07 262 380 / 00
Loading...