Operating and installation instructions
Cooker Hoods
DA 259-2, DA 259-2 U
DA 259-2 EXT,
DA 252-2, DA 252-2 U
DA 252-2 EXT
It is essential to read these
operating instructions before
installing or using the machine
to avoid the risk of accidents or
damage to the machine.
GWOZ
M.-Nr. 06 487 780
Contents
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Description of the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Operation
To switch the fan on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Selecting the power level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Run-on option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
To switch the fan off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Hob lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
To dim the hob lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Switching off the hob lighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Feature lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Filter operating hours counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Reading the filter operating hours counter. . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Altering the filter operating hours counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cleaning and care
Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Grease filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Fitting / replacing the active charcoal filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Changing a light bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Hob illumination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Feature lighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Appliance dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Assembly parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Connection for air extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Condensate trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2
Caring for the environment
Disposal of the packing
material
The transport and protective packing
has been selected from materials which
are environmentally friendly for
disposal, and can normally be
recycled.
Packaging (e.g. cling film, polystyrene)
and plastic wrappings must be kept out
of the reach of babies and young
children. Danger of suffocation!
Dispose of or recycle all packaging
materials safely as soon as possible.
Disposal of your old appliance
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly,
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of your
old appliance with your household
waste.
Please dispose of it at your local
community waste collection / recycling
centre and ensure that it presents no
danger to children while being stored
for disposal.
It should be unplugged or disconnected
from the mains electricity supply by a
competent person. If connected by a
plug, the plug must be rendered
useless and the cable cut off directly
behind the appliance to prevent
misuse. See the "Warning and Safety"
section of this booklet for further details.
3
Warning and Safety instructions
Technical safety
This appliance complies with all
relevant local and national safety
requirements. Inappropriate use
can, however, lead to personal injury
and damage to property.
Before installation and before using
for the first time, read the operating
instructions carefully. They contain
important information on safety,
installation, use and maintenance of
the appliance. This way you will
avoid the risk of accidents and
damage to the appliance.
Keep these operating instructions in
a safe place and ensure that all
users are familiar with the contents.
Pass them on to any future owner of
the appliance.
Correct usage
The appliance is intended for
domestic use only.
The manufacturer cannot be held liable
for damage caused by improper or
incorrect use of the appliance.
the voltage and frequency details given
on the data plate correspond with the
on-site electricity supply, otherwise the
appliance could get damaged. If in any
doubt, consult a qualified electrician.
when continuity is complete between
the appliance and an effective earthing
system which complies with local and
national regulations. It is most important
that this basic safety requirement is
present and regularly tested. If in any
doubt, the electrical wiring should be
checked by a qualified electrician. The
manufacturer cannot be held liable for
the consequences of an inadequate
earthing system (e.g. electric shock).
qualified and competent persons to
ensure safety. Repairs and other work
by unqualified persons could be
dangerous, and the manufacturer will
not be held liable.
Before connecting the appliance to
the mains supply, make sure that
The electrical safety of this
appliance can only be guaranteed
Installation work and repairs may
only be carried out by suitably
This equipment is not designed for
maritime use or for use in mobile
installations such as caravans, aircraft
etc. However it may be suitable for
such usage subject to a risk
assessment of the installation being
carried out by a suitably qualified
engineer.
4
Warning and Safety instructions
The appliance is only completely
isolated from the electricity supply
when:
it is switched off at the wall socket
–
and the plug removed. (Pull on the
plug, not the cable). Or
the fuse from the fused spur
–
connection unit is withdrawn. Or
the screw-out fuse is removed (in
–
countries where this is applicable).
Do not connect the appliance to
the mains electricity supply by an
extension lead.
Extension leads do not guarantee the
required safety of the appliance (e.g.
danger of overheating).
Use
Never use an open flame beneath
the cooker hood. To avoid the
danger of fire, do not flambé or grill
over an open flame.
When switched on, the cooker hood
could draw flames into the filter. Fat
particles drawn into the cooker hood
present a fire hazard.
When using the cooker hood over
a gas hob, ensure that any burners
in use are always covered by a pan.
Otherwise flames could be drawn up by
the suction of the cooker hood, parts of
which could then be damaged.
Always switch the cooker hood on
when a cooking zone is in use,
otherwise condensation may collect in
the hood, which could cause corrosion.
When cooking with oil or fat, chip
pans and deep fat fryers etc, do
not leave the pans unattended. Never
leave an open grill unattended when
grilling.
Overheated oil and fat can ignite and
could set the cooker hood on fire.
Do not use the cooker hood without
the grease filters in place. This way
you will avoid the risk of grease and dirt
getting into the appliance and
hindering its smooth operation.
The filters should be regularly
cleaned or changed as
appropriate.
Saturated filters are a fire hazard. (See
Cleaning and care).
Under no circumstances should a
steam-cleaner be used to clean
this appliance. Pressurised steam
could reach the electrical components
and cause a short circuit.
In countries where there are areas
which may be subject to infestation by
cockroaches or other vermin, pay
particular attention to keeping the
appliance and its surroundings in a
clean condition at all times. Any
damage which may be caused by
cockroaches or other vermin will not be
covered by the appliance guarantee.
5
Warning and Safety instructions
Installation
The minimum safety distance
between the top of a cooker or hob
from our range and the bottom of the
cooker hood should be at least:
– 450 mm above electric hobs and
cookers,
– 650 mm above gas hobs and
cookers,
– 650 mm above an open grill
from our range
For cooking appliances not in our range
please maintain the safety distance as
recommended by the manufacturer in
their Installation and Operating
instructions.
If more than one appliance is fitted
beneath the cooker hood, and they
have different minimum safety
distances to the cooker hood, select
the greater distance.
Safety regulations prohibit the
fitting of a cooker hood over solid
fuel stoves.
All ducting, pipework and fittings
must be of non-flammable material.
These can be obtained from the Miele
Spare Parts Department (see back
cover for contact details) or from
builders’ merchants.
The appliance must not be
connected to a chimney or vent
flue which is in use. Neither should it be
connected to ducting which ventilates
rooms with fireplaces.
If exhaust air is to be extracted into
a chimney or ventilation duct no
longer used for other purposes, seek
professional advice.
6
Warning and Safety instructions
When using the cooker hood at the
same time as another heating
appliance which depends on the air in
the room (e.g. gas, oil or coal fired
heaters, continuous flow or other water
heaters, gas cooker, gas hob or gas
oven), special care must be taken as
the action of the cooker hood extracts
air from the room in which it is installed
and from neighbouring rooms, which
these type of heaters need for
combustion.
They could also draw exhaust air back
in from chimneys or ducting in
contravention of fire safety regulations.
In order to ensure safe operation, and
to prevent gases given off by the
heating appliances from being drawn
back into the room when the extractor
and the heater are in operation
simultaneously, an underpressure in the
room of 0.04 mbar (4 pa) is the
maximum permissible.
Ventilation can be maintained by air
inlets which cannot be blocked, in
windows, doors and outside wall vents,
or by other technical measures such as
ensuring that the extractor can only be
switched on when the heating
appliance is switched off or vice-versa.
Appliances with external motors
For appliances with an external
motor fitted (...EXT models) the
connection of the two units must be
made using the connection cable and
the plug connectors.
Make sure the correct combination of
the two appliances has been selected.
Separate instructions are supplied with
the external motor.
Disposal of your old appliance
Before discarding an old
appliance, switch off and
disconnect it from the power supply.
Cut off and render any plug useless.
Cut off the cable directly behind the
appliance to prevent misuse.
This should be done by a competent
person.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
Note: The overall ventilation condition of
the dwelling must be taken into
account. If in any doubt, the advice of a
competent builder or, for gas, a "Corgi"
installer must be sought.
If the cooker hood is operated in
recirculation mode (with a charcoal
filter), the above restrictions do not
apply.
7
Description of the appliance
8
Description of the appliance
a Extension piece
b Tower
c Canopy
d Grease filters
e Hob lighting
f Recirculation grilles
(only with "...U" models)
g Feature lighting
h Glass shelves
Can take a max. load of 4 kg each
i Shelves
Each side can take a max. load of 8 kg
j Control panel
l Touch control for
the hob lighting
This control switches the lighting on
and off and is also a dimmer switch.
m On/Off-touch control for
the fan
n Controls to select the
fan power level
o Touch control for the
run-on function
This control activates the run-on option.
The fan is switched off automatically
after either 5 or 15 minutes.
p Touch control for the
grease filters
The indicator light for the grease filter
touch control lights up when the grease
filters need to be cleaned.
k On/Off switch for
the feature lighting
The touch control is used:
–
to reset the operating hours counter
after cleaning the grease filters (see
"Cleaning and Care").
–
to show how long the grease filters
have been in use (see section on
"Operation / Filter operating hours
counter")
–
to alter the number of hours counted
by the filter operating hours counter
(see section "Operation / Altering the
filter operating hours counter").
9
Functional description
The cooker hood works with
. . . air extraction
The air is drawn in and cleaned by the
grease filters and directed outside.
The cooker hood is fitted with a
non-return flap.
This flap is closed when the cooker
hood is switched off. No exchange of
room air and outside air can take place.
When the cooker hood is switched on,
the non-return flap opens for the
cooking vapours to be blown directly
outside.
. . . air recirculation:
(only "...U" models)
The air is drawn in and cleaned first by
grease filters and then cleaned by
active charcoal filters. The cleaned air
is then recirculated back into the
kitchen through a vent in the top of the
cooker hood extension piece.
. . . an external fan
The ...EXT models are designed to be
connected to an external fan located
outside the room.
The external fan is connected to the
cooker hood by means of a control
cable and is operated by the control
panel on the cooker hood.
Before using the cooker hood for the
first time, ensure that the active
charcoal filters are in place, see
section on "Cleaning and care".
10
Operation
To switch the fan on
Press the On/Off touch control.
^
The fan runs at power level "lI".
The indicator lamp for the touch control
lights up.
Selecting the power level
^ Use the – /+ controls to select the
power level required.
Touch control + = higher setting
Touch control – = lower setting
Depending on the intensity of cooking
vapours, levels "I" to "III" (green
indicator lamps) are usually sufficient
for normal cooking.
Run-on option
If the air still needs to be cleared after
cooking, the cooker hood can be set to
continue running.
The fan is switched off automatically
after either 5 or 15 minutes.
Press the run-on option touch control
^
whilst the fan is still running.
Press once = The fan switches off
after 5 minutes.
(left hand indicator lamp)
Press twice = The fan switches off
after 15 minutes.
(right hand indicator lamp)
To switch the run-on option off, press
the run-on option touch control again.
To switch the fan off
Intensive setting
When frying or cooking food with a
strong aroma you may wish to select
the Intensive setting (yellow indicator
lamp) for a short period.
^
Use the On/Off touch control to
switch the fan off.
The indicator lamp for the control goes
out.
11
Operation
Hob lighting
The hob lighting can be switched on
and off independently of the fan.
Briefly press the lighting touch control
^
to switch on the hob lighting.
The indicator lamp for the touch control
lights up.
The lighting will come on at maximum
brightness.
To dim the hob lighting
The brightness of the lighting can be
dimmed.
^ With the lighting switched on press
and hold the hob lighting control in.
The brightness will gradually dim until
you release the control.
Switching off the hob lighting
Briefly press the hob lighting control
^
to switch the lighting off.
The indicator lamp for the control goes
out.
Feature lighting
Set the switch to position "I".
^
Safety cut-out
Should the cooker hood have been left
switched on, the fan will switch off
automatically after 10 hours. The
lighting remains on.
^ Pressing the On/Off touch control will
switch the fan back on again.
^
Press the control in again to increase
the brightness to the level required
and then release it.
If you keep the control pressed in, the
brightness will continually go brighter
and then dimmer.
12
Operation
Filter operating hours counter
The number of hours the appliance has
been in operation is stored in memory.
The indicator lamp for the grease filter
control will light up after 30 hours of
operation. The grease filters must then
be cleaned.
After the grease filters have been
cleaned and put in place, the filter
operating hours counter must be re-set.
^ To do this, press the grease filter
touch control for about 3 seconds.
The indicator lamp will go out.
Reading the filter operating hours
counter
To check the percentage of time set
already used:
Use the On/Off touch control to
^
switch the fan on.
^ Press the grease filter touch control.
One or several of the indicator lamps
for the – /+ touch controls will flash.
The number of flashing lamps shows
the percentage of the operating time
which has already been used up.
1 lamp = 25 %
2 lamps = 50 %
3 lamps = 75 %
4 lamps = 100 %
The operating hours completed remain
in memory, even when the machine is
switched off or there is a power cut.
13
Operation
Altering the filter operating hours
counter
The operating hours counter for the
grease filters is set to 30 hours. This
time can be lengthened or shortened.
You can choose from 20, 30, 40 or 50
hours.
Select a short time if you roast or fry
–
a lot.
If you use very little fat for cooking,
–
select a longer time.
If, however, you only cook
–
occasionally we recommend that you
select a short time because grease
which has built up gradually over a
long period of time will harden on the
grease filters and make cleaning
more difficult.
Use the On/Off touch control to
^
switch the fan off.
Press the run-on option touch control
^
and the grease filter touch control at
the same time.
The indicator lamp for the grease filter
touch control and one of the – /+ touch
control lamps will flash.
The – /+ touch control lamps show the
time which has been set:
1st lamp from the left = 20 hours
2nd lamp from the left = 30 hours
3rd lamp from the left = 40 hours
4th lamp from the left = 50 hours
14
^
Use the – /+ touch controls to select
the desired time.
^
Confirm the selection by pressing the
grease filter touch control.
If the procedure is not confirmed
within 4 minutes of programming the
steps, the cooker hood will
automatically revert to the "old" data.
Before any cleaning or maintenance
work the cooker hood must be
disconnected from the mains supply.
Ensure that:
- it is switched off at the wall socket
and the plug has been withdrawn
(do not pull on the cable, only on the
plug), or
– the fuse has been withdrawn from
the fused spur connection unit, or
- the mains fuse is withdrawn, or
- the screw-out fuse is removed (in
countries where this is applicable).
Housing
Warning: The surfaces and controls
are susceptible to scratches and
abrasion. Please observe the
following cleaning instructions:
^ All external surfaces can be cleaned
using warm water with a little washing
up liquid applied with a well wrung
out soft sponge or cloth.
Cleaning and care
abrasive sponges, e.g. pot scourers or
–
sponges which have been previously
used with abrasive cleaning agents.
These will damage the surface material.
E-Cloth
A microfibre "E-Cloth" is available from
the Miele UK Spare Parts Department,
Part number 98013530, which is
suitable for cleaning surfaces such as
stainless steel, glass, plastic and
chrome without the use of chemicals.
Stainless steel
Stainless steel surfaces can be cleaned
using a proprietary non-abrasive
cleaning agent designed specifically
for use on stainless steel.
To help prevent re-soiling, proprietary
conditioning agents for stainless steel
can also be used.
Apply sparingly with an even pressure.
Stainless steel coloured controls
^
Wipe dry using a soft cloth.
Do not use too much water when
cleaning the controls. Water could
penetrate into the electronics and
cause damage.
Avoid:
–
cleaning agents containing soda,
acids or chlorides,
–
abrasive cleaning agents e.g.
powder cleaners or cream cleaners,
These controls are made of stainlees
steel coloured lacquered plastic and
may suffer discolouration or damage
if soiling is left on them for too long.
Remove any soiling straight away.
Do not use stainless steel cleaning
agents on these types of controls.
If you are unsure about a particular
product or need further advice please
contact your nearest Miele Sales
office. See back page for address.
15
Cleaning and care
Grease filters
Re-usable metal filters are fitted which
remove solid particles (oil, dust, etc.)
from the kitchen vapours, preventing
soiling of the cooker hood.
The filters should be cleaned regularly
(at least every 3-4 weeks) to avoid a
build-up of fat, but always clean as
soon as the grease filter touch control
lamp comes on.
An over saturated filter is a fire
hazard.
To take out the grease filters press
^
the locking clips in towards the
middle of the filter. Holding carefully,
lower and remove the filter.
^ Clean the filters
– by hand: with a nylon brush in,
warm water with a little washing up
liquid.
– in a dishwasher: place the filters
with the short side upright in the
lower basket, ensuring the spray arm
is not obstructed.
Depending on the cleaning agent
used, cleaning the grease filters in a
dishwasher can cause permanent
discolouration to the surface of the
filters.
However, this will not affect the
functioning of the grease filters in
any way.
^
After cleaning, leave the filters to dry
on an absorbent surface before
putting them back in place.
16
Cleaning and care
When removing the filters for
^
cleaning also clean off any residues
of oil or fat from the now accessible
housing to prevent the risk of these
catching fire.
When putting the grease filters back in
position, ensure that the locking clips
are visible facing down towards the
hob.
Should the grease filters be put back
upside down insert a small screwdriver
into the slits to disengage them. Do not
let them drop on to the hob below.
After replacing the grease filters,
^
press the grease filter touch control
for approx. 3 seconds to re-set the
operating hours counter.
The indicator lamp will go out.
^ If the grease filters are cleaned
before the operating hours counter
has reached its maximum, the grease
filter touch control should be pressed
for approx. 6 seconds to reset the
counter to zero.
Fitting / replacing the active
charcoal filters
If the cooker hood is connected for
recirculation two active charcoal filters
must be inserted in addition to the
grease filters. These filters absorb
normal kitchen odours.
They are fitted in the canopy above the
grease filters.
Active charcoal filters can be
obtained from your dealer or the
Miele Spare Parts Department.
Refer to the section "Technical data"
for type and reference number.
The filters are supplied with fitting
instructions. Ensure these are carefully
followed.
Replace the filters when they no longer
absorb kitchen odours effectively.
They should, however, be replaced at
least every 6 months.
17
Cleaning and care
Changing a light bulb
Disconnect the cooker hood from
the mains supply by
– switching it off at the wall socket
and removing the plug (do not pull
on the cable, only on the plug), or
– withdrawing the fuse from the fused
spur connection unit (if accessible),
or
– withdrawing the mains fuse, or
– removing the screw-out fuse, (in
countries where this is applicable).
Hob illumination
Changing a halogen light bulb
When in use the halogen bulbs
become very hot. Do not touch immediately as they remain hot for
some time after being switched off.
Do not touch the bulb surface
directly when changing the bulb as
this will damage it. Please follow the
manufacturer’s instructions.
Pull the old halogen light bulb b out
–
of the connection socket and replace
it with a new one.
Replace the lamp cover a carefully
–
making sure it fits securely.
Never use the lighting without the
lamp cover a. It has a filter
designed to cut out harmful rays.
Feature lighting
–
To access the halogen light bulb first
remove the lamp cover a.
18
Changing the compact light tube
^
To change the light tube loosen the
two screws on the lamp cover and
then take the cover off.
^
Carefully lift the light tube upwards
out of the holder and pull it out as
illustrated.
^
Fit the new light tube into the holder
and lower it into position, making
sure it sits securely in the holder.
^
Refit the lamp cover using the two
screws.
In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
Your Miele Dealer
–
or
The Service Department (see back
–
cover for address).
When contacting your Dealer or the
Service Department, please quote the
model and serial number of your
appliance. These are shown on the
data plate which is visible when the
grease filter is removed.
Please note that telephone calls may
be monitored and recorded to
improve our service.
After Sales Service
19
Appliance dimensions
20
Appliance dimensions
The shaded area represents the
wall or ceiling area for the vent
cut-out, for feeding the connection
cable through to an external fan and for
fitting the connection socket.
(For recirculation mode the connection
socket may only be fitted in a wall area).
Connection for air extraction
C 150 mm or C 125 mm with reducing
collar.
To fit the tower, distance A between the
top of the tower and the ceiling must be
at least 30 mm.
Appliance height:
1) Extraction
(only DA 259-2, DA 259-2 EXT,
DA 252-2, DA 252-2 EXT)
2) Recirculation
(only DA 259-2 U, DA 252-2 U)
Safety distance S above a cooker/hob
For safety reasons a minimum safe
distance S must be maintained
between the top of the cooker / hob
and the bottom of the cooker hood:
– 450 mm above
electric cookers / hobs
– 650 mm above gas hobs
– 650 mm above an open grill
from our range.
See "Warning and Safety instructions" for further information.
When deciding dimension S
please note that
– A distance of 650 mm above electric
cookers / hobs may be preferable to
give more working space.
– If the hood is fitted flush to the
ceiling, make sure that the
height of cooker / hob + S + H
is equal to but not greater than the
floor to ceiling height of the room.
21
Installation
Assembly parts
22
a 2 protective sheets
for use when fitting the tower.
b Upper retaining plate for securing
the extension piece and for securing
the directional unit
(only with "...U" models).
c 1 directional unit
(only with "...U" models)
Installation
4 screws 5x60 mm,
4 washers 5.3 mm,
4 plugs S8R60 for securing the lower
retaining plate.
d 1 flexible aluminium hose for
connecting the directional unit to the
exhaust socket on the motor unit.
e 2 hose clips for securing the
exhaust ducting.
f 1 reducing collar for exhaust
ducting C 125 mm
(not on "...EXT" and "...U" models).
g 1 non-return valve for fitting into the
exhaust connection on the motor unit
(not on "...EXT" and "...U" models).
h Middle retaining plate for securing
the extension piece.
i Lower retaining plate for securing
the canopy.
j 2 active charcoal filters
(only with "...U" models)
6 large headed screws 5 x 40 mm and
6 S 8 plugs for securing the retaining
plates.
4 M 6 locking nuts for securing the
canopy and the directional unit.
4 screws 3.9 x 7.5 mm for securing the
tower and the extension piece.
23
Installation
See enclosed installation sheet for
instructions on how to install this
appliance.
Before installation it is important to read
the information given on the following
pages as well as the Warning and
Safety instructions at the beginning of
this book.
24
Danger of toxic fumes.
Please observe the Warning and
Safety instructions to avoid the
danger of toxic fumes.
The cooker hood should be installed
according to local building
regulations. Seek approval from the
building inspector where necessary.
The extraction ducting should be as
–
short and straight as possible.
To ensure efficient air extraction, the
–
diameter of the exhaust ducting
should not be less than 150 mm.
If exhaust ducting with a diameter of
less than 150 mm or flat ducting is
used, the noise level of the cooker
hood will increase and extraction will
be less efficient.
Connection for air extraction
Where ducting is horizontal, it must
–
be laid to slope away at at least 1 cm
per metre.
This is to ensure that condensate
cannot drain back into the cooker
hood.
If the exhaust air is to be ducted into
–
the open air, the installation of a
telescopic wall vent is
recommended.
Only reduce the diameter of the
ducting if absolutely necessary, e.g.
where narrower ducting has already
been installed.
–
Only use wide radius bends. Tight
bends reduce the air throughput of
the cooker hood.
–
Only use smooth pipes or flexible
hoses made from non-flammable
materials for extraction connection.
–
If the exhaust air is to be ducted into
a vent flue, the ducting must be
directed in the flow direction of the
flue.
25
Connection for air extraction
Important:
If the exhaust ducting is to run through
rooms, ceiling space etc. where there
may be great variations in temperature
between the different areas, the
problem of condensation will need to
be addressed. The exhaust ducting
will need to be suitably insulated.
Condensate trap
In addition to insulating the exhaust
ducting, we recommend that a suitable
condensate trap is also installed to
collect and evaporate any condensate
which may occur.
When installing a condensate trap,
ensure that it is positioned vertically
and if possible directly above the
exhaust connection.
Condensate traps are available from
builders merchants.
26
All electrical work should be
undertaken by a suitably qualified
and competent person in strict
accordance with national and local
safety regulations.
Installation, repairs and other work
by unqualified persons could be
dangerous. The manufacturer can
not be held responsible for
unauthorised work.
Ensure power is not supplied to the
appliance while installation or repair
work is being carried out.
U.K., IRL, NZ, ZA: The cooker hood is
supplied for connection to an a.c.
230 V single phase 50 Hz supply.
AUS: The cooker hood is supplied for
connection to an a.c. single phase
240 V, 50 Hz supply.
The voltage, rated load and fusing are
given on the data plate. This is visible
when the grease filters have been
removed. Ensure that these match the
household mains supply.
For U.K.: Connection should be made
either by a double pole fused spur
connection unit, or a fused plug and a
suitable switched socket. The On-Off
switch should be easily accessible after
the appliance has been built in.
When switched off there must be an
all-pole contact gap of 3 mm in the
switch (including switch, fuses and
relays according to EN 60 335).
If the socket is not accessible after
installation (depending on country) an
additional means of disconnection must
be provided for all poles.
Electrical connection
For extra safety it is advisable to install a
residual current device (RCD) with a trip
current of 30 mA (in accordance with
DIN VDE 0664, VDE 0100 Section 739).
Do not connect via an extension lead.
Important UK
If the appliance is fitted with a
non-rewireable plug (BS 1363 UK) and
the socket outlets are not suitable for
the plug supplied, or if the existing plug
needs to be replaced by a new one, the
old plug will need to be cut off and an
appropriate plug fitted. The fuse carrier
and the fuse should be removed from
the old plug and disposed of. The plug
cut from the cable should then be
disposed of, and on no account be
inserted into any socket elsewhere in
the house (electric shock hazard).
The fuse cover must be re-fitted when
changing the fuse and if the fuse cover
is lost the plug must not be used until a
suitable replacement is obtained.
The colour of the correct replacement
cover is that of the coloured insert in
the base of the plug or the colour that is
embossed in words in the base of the
plug (as applicable to the design of
plug fitted).
The correct fuse rating of the
replacement fuses that are ASTA
approved to BS 1362 should be fitted.
Replacement fuse covers may be
purchased from your local electrical
suppliers or Service agent.
27
Electrical connection
Important
The wires in the mains lead are
coloured in accordance with the
following code:
Green/yellow = earth
Blue = neutral
Brown = live
If the appliance is to be connected via
a plug and socket, please note the
following:
As the colours of the wires in the mains
lead of this appliance may not
correspond with the coloured markings
identifying the terminals in your plug,
proceed as follows:
^ The wire which is coloured green and
yellow must be connected to the
terminal in the plug which is marked
with the letter E or by the earth
symbol z or coloured green or green
and yellow.
^ The wire which is coloured blue must
be connected to the terminal which is
marked with the letter N or coloured
black.
^
For U.K., IRL, ZA: The wire which is
coloured brown must be connected
to the terminal which is marked with
the letter L or coloured red.
^
For Australia / New Zealand: The wire
which is coloured brown must be
connected to the terminal which is
marked with the letter A or coloured
red.
WARNING:
THIS APPLIANCE MUST BE
EARTHED
28
Technical data
Rated load
DA 259-2, 259-2 U. . . . . . . . . . . . 278 W
DA 252-2, 259-2 U. . . . . . . . . . . . 298 W
Lighting
DA 259-2, 259-2 U,
259-2 EXT . . . . . . . . . . . . . . . . 3 x 20 W
DA 252-2, 259-2 U,
252-2 EXT . . . . . . . . . . . . . . . . 4 x 20 W
Feature lighting . . . . . . . . . . . . . 2 x 9 W
Voltage
UK, IRL, NZ . . . . . . . . . . . . . . . . . 230 V
AUS . . . . . . . . . . . . . . . . . . . . . . . 240 V
Frequency. . . . . . . . . . . . . . . . . ~ 50 Hz
Fuse rating (UK). . . . . . . . . . . . . . . 13 A
Fuse rating (IRL). . . . . . . . . . . . . . . 10 A
AUS, NZ:
Plug rating . . . . . . . . . . . . . . . . . . . 10 A
Test marks . . . . . . . . . . Electrical safety
. . . . . . . . . . . . . . . . . . . . . . C-Tick Mark
Electrically suppressed
according to AS/NZS 1044
Fan power level
Extraction power according to EN 61591
Extraction system C 150 mm:
Level I . . . . . . . . . . . . . . . . . . . 220 m
Level II. . . . . . . . . . . . . . . . . . . 335 m
Level III . . . . . . . . . . . . . . . . . . 440 m
Intensive level . . . . . . . . . . . . . 640 m
3
3
3
3
Extraction system C 125 mm:
Level I . . . . . . . . . . . . . . . . . . . 210 m
Level II. . . . . . . . . . . . . . . . . . . 305 m
Level III . . . . . . . . . . . . . . . . . . 405 m
Intensive level . . . . . . . . . . . . . 590 m
Unrestricted. . . . . . . . . . . . . . . 690 m
3
3
3
3
3
Recirculation with charcoal filter:
Level I . . . . . . . . . . . . . . . . . . . 180 m
Level II. . . . . . . . . . . . . . . . . . . 290 m
Level III . . . . . . . . . . . . . . . . . . 390 m
Intensive level . . . . . . . . . . . . . 485 m
3
3
3
3
Active charcoal filter:
Miele active charcoal filter DKF 6
/h
/h
/h
/h
/h
/h
/h
/h
/h
/h
/h
/h
/h
For ...EXT models the rated load and
extraction power will depend on the
type of external fan fitted.
293031
Alteration rights reserved / 4904
M.-Nr. 06 487 780 / 01
en-–
Loading...