Miele DA2050 Installation and Operation Guide

Operating and Installation instructions

Rangehood
DA 2050

To avoid the risk of accidents
or damage to the appliance,
it is essential to read these
instructions before it is installed
and used for the first time.

en - AU, NZ

M.-Nr. 09 723 310

Contents

Caring for the environment..........................................3

Warning and Safety instructions .....................................4

Modes of operation ................................................9

Guide to the appliance ............................................10

Operation .......................................................11

To switch the lighting on and off ......................................11

To switch the fan on................................................11

To select a power level .............................................11

Intensive setting ................................................11

Switching off .....................................................11

Cleaning and care ................................................12

Housing .........................................................12

Grease filter ......................................................12

Fitting and replacing the charcoal filters ................................14

Changing a halogen lamp ...........................................15

Appliance dimensions.............................................16

Safety distances between cooktop and rangehood (S) ..................16

Installation ......................................................18

Fitting the non-return flap............................................18

Building in .......................................................18

Preparation for extraction ...........................................19

Electrical connection ...............................................20

Connection for air extraction .......................................21

Condensate trap ..................................................22

Silencer .........................................................23

Electrical connection..............................................24

After sales service ................................................25

Technical data ...................................................26

2

Caring for the environment

Disposal of the packing
material

The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled.

Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation.

Rather than just throwing these
materials away, please ensure they are
offered for recycling.

Disposal of your old appliance
or machine

Electrical and electronic appliances /
machines often contain materials
which, if handled or disposed of
incorrectly, could be potentially
hazardous to human health and to the
environment. They are, however,
essential for the correct functioning of
your appliance or machine. Therefore,
please do not dispose of your old
machine or appliance with your
household waste.

Please dispose of it at your local
community waste collection / recycling
centre and ensure that it presents no
danger to children while being stored
for disposal.

It should be unplugged or disconnected
from the mains electricity supply by a
competent person.
The plug must be rendered useless
and the cable cut off directly behind the
appliance or the machine to prevent
misuse.

3

Warning and Safety instructions

This appliance is not suitable for
This appliance complies with all
relevant local and national safety
requirements. Inappropriate use
can, however, lead to personal
injury and damage to property.

To avoid the risk of accidents and
damage to the appliance, please
read these instructions carefully
before using it for the first time.
They contain important information
on the safety, installation, use and
maintenance of the appliance.

Keep these instructions in a safe
place and ensure that all users are
familiar with the contents. Pass them
on to any future owner of the
appliance.

~

outdoor use.

This appliance is not intended for

~

use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience or knowledge, unless they
are supervised whilst using it or have
been been shown how to use it by a
person responsible for their safety.

This appliance may only be used in

~

mobile installations if a risk assessment
of the installation has been carried out
by a suitably qualified engineer.

Safety with children

This appliance is only intended for

~

use by adults who have read these
instructions.

Correct application

This rangehood is designed for

~

domestic use and for use in similar
environments by guests in hotel or
motel rooms, bed & breakfasts and
other typical living quarters. This does
not include common/shared facilities or
commercial facilities within hotels,
motels or bed & breakfasts.

It must only be used as a domestic

~

appliance to extract vapours and
remove odours from cooking.

Any other usage is not supported by

~

the manufacturer and could be
dangerous. Miele cannot be held liable
for damage resulting from incorrect or
improper use or operation of the
appliance.

4

This appliance is not a toy! To avoid

~

the risk of injury, keep children well
away and do not allow them to play with
it or to use the controls. They will not
understand the potential dangers
posed by it. They should be supervised
whenever you are working in the
kitchen.

Older children may use the

~

rangehood only when its operation has
been clearly explained to them and
they are able to use it safely,
recognising the dangers of misuse.

Please be aware that on rangehood

~

with halogen lighting, the lamps will get
very hot during use and remain hot for
some time after switching off. To
safeguard against burning, keep
children well away from the lamps at all
times.

Warning and Safety instructions

Technical safety

Before installation, check the

~

rangehood for visible signs of damage.
Under no circumstances should you
use a damaged appliance. A damaged
appliance is dangerous.

Before connecting the appliance to

~

the mains supply, make sure that the
voltage and frequency details given on
the data plate correspond with the
on-site electricity supply, otherwise the
appliance could be damaged. Consult
a qualified electrician if in any doubt.

The electrical safety of this

~

appliance can only be guaranteed
when continuity is complete between
the appliance and an effective earthing
system which complies with current
local and national safety regulations. It
is most important that this basic safety
requirement is present and tested
regularly and, where there is any doubt,
the household wiring system should be
inspected by a qualified electrician.
The manufacturer cannot be held liable
for the consequences of an inadequate
earthing system (e.g. electric shock).

Installation, maintenance and

~

repairs may only be carried out by a
Miele authorised person in accordance
with current national and local safety
regulations.
Repairs and other work by unqualified
persons could be dangerous. The
manufacturer cannot be held liable for
unauthorised work.

A damaged connection cable must

~

only be replaced by an approved and
suitably qualified technician.

Faulty components must only be

~

replaced by genuine Miele original
parts. The manufacturer can only
guarantee the safety of the appliance
when Miele replacement parts are
used.

During installation, maintenance and

~

repair work, the appliance must be
disconnected from the mains electricity
supply. It is only completely isolated
from the electricity supply when:

–

it is switched off at the isolator, or

–

the screw-out fuse is removed (in
countries where this is applicable), or

For safety reasons, this appliance

~

may only be used when it has been
fully installed.

Only open the housing as described

~

in the instructions given in the
installation sheet and in the Cleaning
and care section of this booklet. Under
no circumstances should any other
parts of the housing be opened.
Tampering with electrical connections
or components and mechanical parts is
highly dangerous to the user, and can
cause operational faults.

–

the mains fuse is disconnected, or

–

it is switched off at the wall socket
and the plug withdrawn.

5

Warning and Safety instructions

Do not connect the appliance to the

~

mains electricity supply by a
multi-socket unit or an extension lead.
These do not guarantee the required
safety of the appliance (e.g. danger of
overheating).

This rangehood must not be

~

installed and operated in mobile
installations (e.g. on a ship).

In areas which may be subject to

~

infestation by cockroaches or other
vermin, pay particular attention to
keeping the appliance and its
surroundings in a clean condition at all
times. Any damage which may be
caused by cockroaches or other vermin
will not be covered by the warranty.

Using at the same time as other
heating appliances that depend on
the air from the room

Warning - danger of toxic fumes

Great care should be taken when

~

using the rangehood at the same time
and in the same room or area of the
house as another heating appliance
which depends on the air in the room.
Such appliances include gas, oil, wood
or coal-fired boilers and heaters,
continuous flow or other water heaters,
gas cooktops or ovens which draw air
in from the room and duct exhaust
gases out through a chimney or
extraction ducting.
When used in extraction mode, the
appliance draws air in from the room in
which it is installed and from
neighbouring rooms.
If there is insufficient air, an
underpressure will occur. The heating
appliance may be starved of oxygen,
impairing combustion.

Harmful gases could be drawn out of
the chimney or extraction ducting back
into the room, with potentially fatal
consequences.

6

Warning and Safety instructions

In order to ensure safe operation, and
to prevent gases given off by the
heating appliances from being drawn
back into the room when the rangehood
and the heater are in operation
simultaneously, an underpressure of

0.04 mbar (4 pa) is the maximum
permissible in the room.

Ventilation can be maintained by air
inlets which must not be blocked, in
windows, doors and outside wall vents,
or by other technical measures, such
as ensuring that the rangehood can
only be switched on when the heating
appliance is switched off or vice versa.
A ventilation brick alone is not generally
sufficient to ensure safe ventilation.

,

The overall ventilation condition
of the dwelling must be taken into
account. If in any doubt, the advice
of a competent builder or, for gas, a
qualified gas fitter must be sought.

Correct use

Never use an open flame beneath

~

the rangehood. To avoid the danger of
fire, do not flambé or grill over an open
flame.
When switched on, the rangehood
could draw flames into the filter. Fat
particles drawn into the rangehood
present a fire hazard.

When using the rangehood over a

~

gas cooktop, ensure that any burners in
use are always covered by a pan.
Switch the cooking zone off when a pan
is removed, even for a short time.
Regulate the flame so that it does not
burn up the sides of the pan.
Do not allow the pans to overheat
excessively (e.g. when using a wok).
The rangehood can become damaged
when exposed to excessive heat.

Always switch the rangehood on

~

when a cooking zone is in use,
otherwise condensation may collect in
the hood, which could cause corrosion.

When cooking with oil or fat, chip

~

pans and deep fat fryers etc., do not
leave the pans unattended. Never leave
an open grill unattended when grilling.
Overheated oil and fat can ignite and
could set the rangehood on fire.

If in any doubt , the advice of a
qualified builder, gas fitter or
electrician must be sought.

If the rangehood is being operated in
recirculation mode, the above
restrictions do not apply.

7

Warning and Safety instructions

Do not use the rangehood without

~

the filters in place. This way you will
avoid the risk of grease and dirt getting
into the appliance and hindering its
smooth operation.

The filters should be regularly

~

cleaned or changed as appropriate.
Saturated filters are a fire hazard. See
"Cleaning and care".

The rangehood can get very hot

~

during cooking due to heat rising from
the cooktop.
Do not touch the housing or the grease
filters until the rangehood has cooled
down.

Do not use a steam-cleaner to clean

~

this appliance. Steam could reach the
electrical components and cause a
short circuit.

Correct installation

Refer to the cooktop manufacturer's

~

instructions as to whether a rangehood
may be operated above the cooktop.

Safety regulations prohibit the fitting

~

of a rangehood over solid fuel stoves.

All ducting, pipework and fittings

~

must be of non-flammable material.
These can be obtained from Miele or
from builders' merchants.

The appliance must not be

~

connected to a chimney or vent flue
which is in use. Neither should it be
connected to ducting which ventilates
rooms with fireplaces.

If exhaust air is to be extracted into

~

a chimney or ventilation duct no longer
used for other purposes, seek
professional advice.

Accessories

Only use genuine Miele spare parts

~

and accessories with this appliance. If
spare parts or accessories from other
manufacturers are used, this will
invalidate the warranty, and Miele
cannot accept liability.

The minimum safety distances

~

between the top of the cooktop and the
bottom of the rangehood given in the
"Appliance dimensions" section of this
booklet must be maintained, unless the
cooktop manufacturer states that a
greater safety distance is required.

If more than one cooking appliance is
fitted beneath the rangehood, and they
have different minimum safety
distances to the rangehood, select the
greater distance.

8

The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.

The rangehood works with

Modes of operation

. . . air extraction:

The air is drawn in, cleaned by the
grease filter and then directed outside.

If the on-site ventilation system does
not have a non-return flap, then the
non-return flap supplied with the
appliance must be fitted in the exhaust
socket in the motor unit.

Having a non-return flap fitted in the
ducting ensures that air, once ducted
to the outside, cannot get back into the
room again.

The flap is closed when the rangehood
is switched off.

When the rangehood is switched on,
the non-return flap opens for the
cooking vapours to be blown directly
outside.

Please note, the performance of
this rangehood hinges greatly on
the installed ducting to vent the
vapours. Poor choice of ducting
results in poor rangehood
performance. For ducting
recommendations, please refer to
the relevant section in these
operating instructions or contact
a specialised installer.

. . . air recirculation:

(requires a conversion kit and charcoal
filters: see "Technical Data")

The air is drawn in and cleaned first by
the grease filter and then by two
charcoal filters. The cleaned air is then
recirculated back into the kitchen.

Before using the rangehood in
recirculation mode, ensure that the
charcoal filters are in place. See
"Cleaning and care".

9

Guide to the appliance

a Lighting switch

b Fan switch

c Cooktop lighting

d Charcoal filters

Special accessory for recirculation
mode

e Grease filter

10

To switch the lighting on and
off

The cooktop lighting a can be
switched on and off independently of
the fan.

"0" - lighting off

"1" - lighting on

To switch the fan on

Turn switch b for the fan to "1".

^

To select a power level

You can select one of three power
levels with switch b depending on how
much the air needs to be filtered.

Depending on the intensity of the
cooking vapours, levels "1" and "2" are
usually sufficient for normal cooking.

Operation

Intensive setting

For short periods of cooking food with
intensive vapours and a strong aroma,
e.g. when searing meat, you may wish
to select the Intensive Setting "IS".

After cooking

If the air still needs to be cleared after
cooking, we recommend letting the
rangehood continue to run for a further
ten minutes.

Then switch the appliance off.

Switching off

^

Turn switch b for the fan to "0".

11

Cleaning and care

Before any cleaning or maintenance
work is carried out, disconnect the
rangehood from the mains supply.
Ensure that:
– it is switched off at the isolator,
or – it is switched off at the wall

socket and the plug
removed, or – the mains fuse is
withdrawn, or
– the screw-out fuse is removed

(in countries where this is
applicable).

A range of Miele branded cleaning and
conditioning agents are available to
order through your Miele Chartered
Agent from Miele or via the internet on
www.miele-shop.com.

Housing

abrasive cleaning agents, e.g.

–

powder cleaners or cream cleaners
and abrasive sponges, as well as pot
scourers or sponges which have
been used previously with abrasive
cleaning agents.
These will damage the surface
material.

Grease filter

The re-usable metal grease filter in the
appliance removes solid particles from
the kitchen vapours (grease, dust, etc.)
preventing soiling of the rangehood.

The surfaces and controls are
susceptible to scratches and
abrasions. Please observe the
following cleaning instructions.

^

All external surfaces and controls can
be cleaned using the Original Miele
all purpose microfibre cloth, or with
warm water and a small amount of
washing-up liquid applied with a well
wrung-out soft sponge or cloth.

^

Wipe the surfaces dry using a soft
cloth.

Do not use:

–

cleaning agents containing soda,
acids, chlorides or solvents,

12

Clean the grease filter when it looks
dirty, and avoid letting it become so
dirty that the filtering effect is inefficient.

To avoid a build-up of fat, it should be
cleaned every 3-4 weeks on average,
but sooner if necessary.

,

An oversaturated filter is a fire

hazard.

^

To take out the grease filter, release
the locking clip on the filter, lower the
filter 45°, unhook it at the back and
remove it.

To avoid damaging the filter or the
cooktop below, make sure you hold
the filter securely at all times when
handling it.

Cleaning and care

When removing the filter for cleaning,

^

also clean off any residues of oil or
fat from the now accessible housing
to prevent the risk of these catching
fire.

Cleaning the grease filter by hand

Clean the filter with a soft nylon brush

^

in a mild solution of hot water and a
small amount of washing-up liquid.
Do not use undiluted washing-up liquid.

Do not use:

cleaning agents containing

–

descaling agents,

– powder cleaners, cream cleaners or

abrasive all-purpose cleaning agents,

– oven sprays.

Cleaning the grease filter in the
dishwasher

^ Place the filters as upright as

possible in the lower basket. Ensure
the spray arm is not obstructed.

^

Do not wash at more than 65 °C. If a
Miele dishwasher is being used,
select the Sensor wash programme.

When putting the grease filter back in
position, ensure that the locking clip is
visible facing down towards the
cooktop.

^ If the grease filter is inadvertently

replaced upside down, insert a small
screwdriver blade into the slit to
disengage the clip.

^

Use a mild dishwasher detergent.

Depending on the cleaning agent
used, cleaning the filters in a
dishwasher can cause permanent
discolouration to the surface.
However, this will not affect the
functioning of the filters in any way.

^

After cleaning, leave the filter to dry
for a while on an absorbent surface
before putting it back in place.

13

Cleaning and care

Fitting and replacing the
charcoal filters

If the rangehood is connected for
recirculation, two charcoal filters must
be inserted in addition to the grease
filter. They are designed to absorb
cooking odours and are fitted in the
canopy above the grease filter.

New filters can be purchased from
your Miele Chartered Agent or from
Miele. See back cover for contact
details, and "Technical data" for the
model number of the filter.

^ Before fitting or replacing the active

charcoal filters, the grease filter must
first be taken out, (see previous
section for instructions on how to do
this).

^ Unwrap the charcoal filters.

Replace the charcoal filters when they
no longer absorb kitchen odours
effectively.

They should, however, be replaced at
least every 6 months.

Used charcoal filters can be disposed
of with the normal household waste.

^

Insert the charcoal filters into the
canopy.

^

Replace the grease filter.

14

Changing a halogen lamp

Before any cleaning or maintenance
work is carried out, disconnect the
rangehood from the mains supply.
Ensure that:
– it is switched off at the isolator,
or – it is switched off at the wall

socket and the plug removed,
or
– the mains fuse is withdrawn, or
– the screw-out fuse is removed

(in countries where this is
applicable).

^ Remove the grease filter.

^ Remove the charcoal filters if the

rangehood is being used in
recirculation mode.

Cleaning and care

^ Push down the lighting unit slightly

via the opening in the safety panel.

,

Exercise caution when changing
halogen lamps. They get very hot
during use, and remain hot for some
time after being switched off.
Do not touch the surface directly
when changing a lamp, as grease
particles from your fingers will
adhere to the surface and damage
it. Please follow the manufacturer's
instructions.

^ The halogen lamp is now accessible

and should be unscrewed
anti-clockwise.

^ Replace it with a new halogen lamp

(specification: GU/GZ 10, 230 V,
50 W). Screw the lamp into the
socket and push it upwards.
Please follow the manufacturer's
instructions.

We recommend only using lamps of the
same specification and also made by
the same manufacturer as the ones
being replaced.

^

Replace the grease filter and, if being
used in recirculation mode, the
charcoal filters.

15

Appliance dimensions

*Cut-out dimensions
A depth T of at least 25 mm must be

provided at the back of the building-in
niche.

Safety distances between cooktop
and rangehood (S)

The minimum safety distances
between the top of a cooktop and
the bottom of the rangehood are
as follows, unless a greater
distance is specified by the
manufacturer of your cooking
appliance:

Cooking appliance Distance

S

Electric cooktop 600 mm

Open electric grill 650 mm

Deep fat fryer (electric) 650 mm

Multi-burner gas cooktop
with maximum 45.4 MJ/h
total output, with no burner
having a greater output
than 16.2 MJ/h.

650 mm

16

Multi-burner gas cooktop
with total output greater
than 45.4 MJ/h, or a gas
cooktop including a single
burner with an output
greater than 16.2 MJ/h.

Single gas cooktop with a
maximum output of

21.6 MJ/h

Single gas cooktop with a
maximum output greater
than 21.6 MJ/h

See "Warning and Safety"
instructions for further information.

760 mm

650 mm

760 mm

When deciding on the safety

–

distance between the cooktop and
rangehood, please note that a
distance of 650 mm above electric
cooktops may be preferable to give
more working space under the hood.

Account should also be taken of the

–

height of the person who will be
using the hood most often. The
person should have sufficient space
to work comfortably at the cooktop,
and also be able to reach the
rangehood controls with ease.

Please be aware that if positioned

–

too high, extraction will be inefficient.

Appliance dimensions

17

Installation

Fitting the non-return flap

(Air extraction mode only)

Place the appliance in the cut-out

^

from below and align it.

^ If a non-return flap is not present in

the venting system, the non-return
flap supplied must be fitted onto the
exhaust socket in the motor unit. The
flaps must open upwards.

Building in

The rangehood is intended to be built
into wall units, rangehood housing
units, and above breakfast bars or
island areas.

Check prior to installation that the top of
the appliance will be accessible after
installation.

If this is not the case, install the exhaust
ducting and prepare the electrical
connection before installation.

^ Secure the rangehood by the frame

using 3.5 x 16 mm screws.

^

Before using the appliance for the
first time, take the grease filters out
and remove the protective foil from
the filter frame. Then replace the
grease filters.

18

Installation

Preparation for extraction

When using C 150 mm ducting,

^

secure the exhaust connection
supplied to exhaust ducting with
hose clips.

Recirculation

^

Place the exhaust ducting on the fan
connection for the rangehood.

^

See "Connection for air extraction" for
further instructions on fitting the
ducting.

If site conditions are not suitable for the
rangehood to be used with air
extraction, the appliance must be set
up for recirculation.

For this, conversion kit DUU 151
(available from Miele Chartered Agent
or Miele) is required.

You will also need two charcoal filters
(see “Technical data”).

19

Installation

Dismantle the non-return flap.

^

Take the on-site conditions into

^

account when fitting the conversion
kit.
When fitting the exhaust grille, make
sure that the slats in the grille point
towards the centre of the room and
not directly towards a wall or the
ceiling.

Fit the charcoal filters.

^

Electrical connection

Before connecting the appliance,
read the safety notes in "Warning
and Safety instructions" and
"Electrical connection".

20

Important: To avoid the danger of
toxic fumes, please observe the
Warning and Safety instructions.
This is especially crucial when using
the rangehood at the same time as
another heating appliance which
relies on air from the same room.
The rangehood should be installed
according to local and national
building regulations. Seek approval
from the building inspector where
necessary.

Only use smooth pipes or flexible

–

hoses made from non-flammable
materials for the extraction ducting.

Connection for air extraction

The exhaust ducting should not be

–

kinked or compressed.

Ensure that all connections are

–

strong and airtight.

Where ducting is horizontal, it must

–

be laid to slope away at at least 1 cm
per metre. This is to ensure that
condensate cannot drain back into
the rangehood.

To achieve the greatest possible air
extraction with the lowest noise level,
please note the following:

– To ensure efficient air extraction, the

diameter of the exhaust ducting
should not be less than 150 mm.

– If flat ducting is being used, the

cross-sectional area must not be
smaller than the cross-sectional area
of the exhaust connection.

If exhaust ducting with a diameter of
less than 150 mm, or if flat ducting is
used, the noise level of the
rangehood will increase and
extraction will be less efficient.

–

All ducting, pipework and fittings
must be of non-flammable materials.

–

The exhaust ducting should be as
short and straight as possible.

–

Only use wide radius bends.

– If the exhaust air is to be ducted into

the open air, the installation of a
telescopic wall vent or roof vent
(available as an optional accessory)
is recommended.

– If the exhaust air is to be ducted into

a vent flue, the ducting must be
directed in the flow direction of the
flue.

Important:

If the exhaust ducting is to run through
rooms, ceiling space etc. where there
may be great variations in temperature
between the different areas, the
problem of condensation will need to
be addressed. The exhaust ducting will
need to be suitably insulated.

21

Connection for air extraction

Condensate trap

(optional accessory)

For installations in areas where the
exhaust ducting is exposed to cold
temperatures, we recommend
insulating the exhaust ducting and
installing a condensate trap to collect
and evaporate any condensate which
may occur. Condensate traps are
available for C 125 mm or C 150 mm
ducting.

When installing a condensate trap,
ensure that it is positioned vertically
and, if possible, directly above the
exhaust connection. The arrow on the
housing indicates the direction of
air-flow.

22

Silencer

(DASD 150, optional accessory)

To achieve even further reductions in
noise levels, a special silencer can be
fitted in the ducting system.

Connection for air extraction

...with air extraction:

The silencer not only reduces noise
from the fan, but also sounds from
outside (e.g. traffic noise).
For this reason, the silencer must be
positioned as close as possible to where
the ducting leaves the building a.

...in recirculation mode:

The silencer needs to be positioned
between the fan and the exhaust grille
b. Ensure there is adequate space for
fitting it.

In all modes of operation, the most
effective noise reductions are
achieved if two silencers are fitted in
the system.

23

Electrical connection

All electrical work should be
undertaken by a suitably qualified
and competent person in strict
accordance with current national
and local safety regulations.

Installation, repairs and other work
by unqualified persons could be
dangerous, for which the
manufacturer cannot be held liable.

Ensure power is not supplied to the
appliance until after installation or
repair work has been carried out.

Do not connect the appliance to the
mains electricity supply by an
extension lead. These do not
guarantee the required safety of the
appliance.

The connection data is given on the
data plate. This is visible when the

grease filters have been removed.
Ensure that this data matches the
household mains supply.

Connection of this appliance should be
made via a suitable isolator which
complies with national and local safety
regulations and the On-Off switch
should be easily accessible after the
appliance has been built in.

If the switch is not accessible after
installation, an additional means of
disconnection must be provided for all
poles.

For extra safety, it is advisable to install
a suitable residual current device
(RCD). Contact a qualified electrician
for advice.

Important

This appliance is supplied for
connection to an AC 230 V single
phase 50 Hz supply.

The wires in the mains lead are
coloured in accordance with the
following code:

Green/yellow = earth
Blue = neutral
Brown = live

WARNING:
THIS APPLIANCE MUST BE
EARTHED

If the connection cable is damaged, it
must be replaced by the manufacturer
or similarly qualified persons to avoid a
hazard.

24

In the event of a fault which you cannot
correct yourself, please contact:

Miele

–

You will find the telephone number
and address of Miele on the back
cover of the manual.

Please quote the model and serial
number when contacting Miele. These
are shown on the data plate which is
visible when the grease filters are
removed.

Warranty

The warranty for this appliance is
2 years.

For further information, please refer to
your warranty booklet.

After sales service

25

Technical data

Total rated load ..............185W

- Fan motor ..................85W

- Cooktop lighting ..........2x50W

Voltage ................. AC230V

Frequency ................. 50Hz

Fuse rating ....................5A

Electrical cable length .........1.5m

Weight.......................8kg

Fan performance

Extraction power according to
EN 61591

Extraction system C 150 mm:

Level I ...................150m

Level II...................280m

Level IV Intensive Setting ....400m

Recirculation with charcoal filters:

Level I ...................120m

Level II...................230m

Level IV Intensive Setting ....360m

Special accessories for recirculation
mode:

–

Conversion kit DUU 151

–

Miele charcoal filter pack DKF 15-1
(each pack contains 2 filters)

3

/h

3

/h

3

/h

3

/h

3

/h

3

/h

26

27

Alteration rights reserved / 3013

M.-Nr. 09 723 310 / 00