MIDLAND XTC-100 User Manual [ru, it, en]

XTC-100 Action Camera

Grazie per aver acquistato XTC-100 Action Camera. XTC-100 è la nuovissima videocamera grandangolo in grado di registrare ed immortalare i vostri momenti più importanti e divertenti! Facile da utilizzare: con il suo unico comando

IUK

(on-off/record), grand’angolo con una visuale di 140° e 2 ore di batteria non vi perderete 1 minuto delle vostre avventure! Terminata la registrazione, connettete semplicemente la videocamera al vostro computer e scaricate i video registrati. Più facile di così! Buon divertimento!

Contenuto della confezione

› Midland XTC-100 Action camera › Micro SD card da 2GB › 2 batterie AAA alcaline › Cavo USB › Supporto montaggio per maschere da sci › Supporto adesivo per montaggio al casco › Supporto a slitta da abbinare con il supporto per maschere da sci e/o supporto per casco › Supporto a cinghia per montaggio al casco da bici › Supporto per manubrio da bici

Caratteristiche e pulsanti del XTC-100

Caratteristiche:

› Risoluzione 640x480 (4:3) › Filmati AVI › 30 frames per secondo › Grand’angolo di 140°

Selettore Record

In avanti:

on/registrazione

Led di registrazione

lampeggia rosso

mentre registra

Led batteria

Selettore Record

Indietro: Off/Stop registrazione

Led SD Card

Guida rapida all’uso

1. Aprite il coperchio del vano batterie ed inserite le batterie facendo attenzione alla polarità. Riposizionate il coperchio del vano batterie.

2. Aprite la cover di gomma della parte inferiore del dispositivo. Inserite la Micro SD card nell’opportuna direzione. Chiudete la piccola cover gommosa.

3. Spostate il selettore RECORD in avanti. La registrazione inizierà dopo 8 secondi circa.

4. Per fermare la registrazione slittate il selettore verso il basso in posizione “off”.

5. Collegate la videocamera al computer e scaricate il video.

Grandangolo 140°

Microfono

Scanalature per montaggio del supporto a slitta

riformattazione SD Card

Connettore

Mini USB

Pulsante per

Vano inserimento

Mini SD Card

Imparando a conoscere XTC-100

Batterie

1. Per inserire le batterie, premete il pulsante posto sul lato destro della videocamera e rimuovete il coperchio del vano batteria facendolo slittare in avanti.

2. Inserite 2 batterie AAA facendo attenzione alla polarità di esse.

3. Riposizionate il coperchio del vano batterie

Indicatore stato batterie Signicato

Verde sso Batteria carica Rosso sso Batteria parzialmente carica

Rosso lampeggiante Batteria quasi scarica Led spento Batteria scarica

Nota: quando l’indicatore di batteria inizia a lampeggiare rosso, sarebbe opportuno cambiare le batterie in quanto la telecamera si spegnerà a breve.

Micro SD Card

1. Aprite la cover di gomma posta sulla parte inferiore della videocamera

2. Inserite la Micro SD nell’apposita fessura come mostrato nell’immagine a lato.

3. Chiudete la cover di gomma.

Registrazione

1. Slittate il selettore di registrazione in avanti per accendere la videocamera.

2. L’indicatore di batteria si illuminerà prima rosso, per poi passare a verde, mentre l’indicatore della Micro SD card si illuminerà di verde. Dopo circa 8 secondi l’indicatore di registrazione inizierà a lampeggiare rosso, indicando che la registrazione è iniziata.

3. Per fermare la registrazione. Spostate il selettore “record” in posizione “off”.

Nota: pur avendo spostato il selettore in posizione “off”, la videocamera continuerà a registrare per altri 3 secondi;

dopodiché si spegnerà denitivamente.

Indicatore stato del SD card Signicato

Verde Più 1GB di spazio disponibile Arancione Da 512 MB a1 GB di spazio disponibile Rosso Meno di 512 MB di spazio disponibile o Micro SD card non inserita. Rosso lampeggiante Micro SD card non letta correttamente Verde lampeggiante Indica che la Micro SD card è stata riformattata

Spazio di memoria Tempo di registrazione

512 MB 7.5 minuti 1 GB 15 minuti 2 GB 30 minuti. 4 GB 60 minuti 8 GB 120 minuti 16 GB 240 minuti 32 GB 480 minuti

Nota: La videocamera dividerà automaticamente i video in documenti da 2GB di dimensione.

Supporti di montaggio

Montaggio al supporto a slitta

XTC-100, con il suo innovativo design a scanalature può essere facilmente montato su uno speciale supporto a

slitta. Tale supporto permette una più facile ed efcace

installazione del dispositivo. Per montare la telecamera al supporto, posizionatela nell’apposita scanalatura e fatela slittare. Per staccare la telecamera dal supporto a slitta, tenete la telecamera con la lente distante da voi e premendo il pulsante di rilascio tirate il supporto verso di voi.

Questo supporto a slitta può essere abbinato sia al supporto bi-adesivo da casco che al supporto per maschera da sci, evitando così di dover rimontare la telecamera ogni volta.

Supporto adesivo per casco Supporto per maschera da sci

Una volta montata la telecamera al supporto a slitta occorre:

1. Montare la telecamera al supporto intercambiabile

più adatto in base a ciò che si desidera lmare.

2. Aggiustare l’inquadratura della videocamera in modo

che non lmi il cielo o il terreno.

Montaggio con supporto a vite

XTC-100 può essere montato sui caschi da bici o sui

manubri delle biciclette tramite due specici supporti

a vite. Nella parte inferiore del XTC-100 vi è un foro di

ssaggio che permette di montare la telecamera su tali

Foro di ssaggio Vite di ssaggio

supporti, inserendo semplicemente la vite di ssaggio

nell’apposito foro e ruotando la telecamera in senso orario.

Se volete ssare la telecamera al manubrio della vostra

bicicletta o montarla sul casco tramite supporto a cinghia, dovete:

1. Montare la telecamera sul supporto a vite più adatto

Supporto a cinghia per casco da bici Supporto al manubrio

a ciò che si desidera lmare.

2. Assicurarsi che la telecamera sia posizionata nel modo corretto e che non inquadri cielo o terra.

Sistemi compatibili

XTC-100 è compatibile sia con sistemi operativi Windows che con MAC. Il formato video è: AVI.

Download dei video

Non c’è bisogno di installare ulteriori software per il collegamento con XTC-100. Prima di scaricare i video, assicuratevi che le batterie siano nuove o completamente cariche.

Connettete la telecamera alla porta USB usando il cavo in dotazione. La telecamera viene vista dal PC come una normalissima memoria esterna (chiavetta USB). Troverete i vostri video salvati nella cartella “DC IM”.

Supporto a slitta con regolazione dell’inclinazione

Pulsante di rilascio

Come riformattare la Micro SD card

La riformattazione della Micro SD card permette di cancellare tutti i le video in un unico istante. Per far ciò occorre che la

micro SD card sia all’interno della stessa telecamera.

1. Posizionate la telecamera in “on” spostando il selettore “record” in posizione di registrazione.

2. Una volta che l’indicatore di batteria si illumina verde, tener premuto il pulsante di riformattazione della Micro SD card.

3. Tenete premuto il pulsante di riformattazione nché l’indicatore di registrazione non si spenga e l’indicatore dell’SD card non lampeggi verde.

4. Spostate il selettore “record” in posizione off.

Nota: la Micro SD card non può essere riformattata se l’indicatore di batteria quasi scarica si accende (rosso lampeggiante). Assicuratevi che le batterie siano completamente cariche o nuove prima di iniziare il processo di riformattazione.

Problemi & Soluzioni

Problemi Soluzioni

Batterie

La telecamera non si accende Assicuratevi che le batterie siano installate correttamente facendo attenzione alla

Registrazione

La telecamera non registra Assicuratevi di aver spostato correttamente il selettore “record” (totalmente in

Micro SD card

La Micro SD card non viene letta Assicuratevi che la Micro SD card sia stata inserita correttamente.

Visualizzazione Video

Il video è lento e si inceppa Vericate che il cavo USB sia stato inserito correttamente nella presa della telecamera

Download del Video

Trasferimento dati lento Vericate che il cavo USB sia stato inserito correttamente nella presa della teleca-

Il computer non riconosce la telecamera

Audio

Disturbi causati dal vento Applicate del nastro adesivo sul foro del microfono

polarità. Assicuratevi che siano nuove o completamente cariche.

avanti). Se l’indicatore di registrazione non si accende spegnete il dispositivo e re-installate le batterie.

Vericate che ci sia abbastanza memoria nella Micro SD card.

Connettete la telecamera al computer per vericare che ci sia abbastanza spazio

di memoria Attendete che si concluda il processo di formattazione

Rimuovete dispositivi USB al momento non utilizzati

Trasferite i le video sul computer prima di vederli

mera. Scollegate e ricollegate il cavo USB Rimuovete dispositivi USB al momento non utilizzati Assicuratevi che la telecamera collegata al computer abbia il selettore “record” po-

sizionato nella giusta posizione Assicuratevi che la Micro SD card sia stata inserita correttamente La Micro SD card potrebbe essere corrotta. Attendete che si concluda il processo

di formattazione

Garanzia

› Il consumatore è titolare di diritti secondo la legislazione nazionale applicabile disciplinante la vendita dei beni di

consumo e la garanzia lascia impregiudicati tali diritti;

› La durata della garanzia è di mesi 24 a decorrere dalla data di acquisto o dalla data della ricevuta rilasciata dal

rivenditore; per farla valere l’utente deve presentare lo scontrino d’acquisto assieme al box dell’apparato acquistato ;

› La garanzia copre l’apparecchio nella totalità delle sue parti e comprende sia il materiale che la manodopera

necessaria per le riparazioni ;

› La garanzia non copre i difetti causati dall’uso o collegamento del Prodotto con accessori o/e software non prodotti o

forniti dal Produttore o da un uso del prodotto diverso da quello per cui il prodotto medesimo è stato realizzato. Essa

non è valida in caso di apertura, modica o riparazione da parte di soggetti diversi dai centri autorizzati o in caso di

riparazioni effettuate con ricambi non autorizzati.

› Nulla sarà dovuto all’acquirente per il tempo durante il quale l’apparecchio sarà rimasto inattivo né egli potrà

pretendere risarcimenti o indennizzi per spese sostenute come pure per danni diretti o indiretti derivanti dall’uso dell’apparecchio.

Noi, CTE International dichiariamo che il prodotto XTC-100 è conforme ai requisiti essenziali e alle disposizioni della Direttiva della Compatibilità elettromagnetica 2004/108/CE. È possibile consultare una consultare una copia della Dichiarazione di Conformità al seguente indirizzo internet: www.midlandradio.eu

XTC-100 Action Camera

Thank you for your purchase of the XTC-100 Action Camera. As someone who seeks adventure, we are proud to offer you the ultimate tool in capturing and recording your adventures. With easy to use one switch operation, 140 degree algle lens and 2 hour battery life you never miss a minute of the action. Once captured, simply connect to your computer and upload the videos to share with friends. It is that simple! Enjoy!

What’s in the box

› Midland XTC-100 Action camera › 2 GB Micro SD card › 2 AAA Alkalinebatteries › USB cable › Goggle mount › Helmet adhesive mount › Dual Track mount for goggle mount and helmet adhesive mount. › Helmet strap mount › Bicycle handlebar mount

XTC-100 Features and Controls

Features:

› 640x480 resolution (4:3 aspect ratio) › Records as AVI › 30 frames per second › 140 degree angle lens

Record switch

forward:

on/record

Record led

ashes red when

camera is recording

Battery led

Record switch

backward: Off/Stop recording

SD Card led

Quick Start Guide

1. Open battery door and install batteries observing polarity. Replace battery cover.

2. Open and fold down back rubber cover. Insert micro Sd card observing proper direction. Close cover.

3. Move RECORD switch forward, recording will start in 8 seconds.

4. To stop recording, slide switch back to the off position.

5. Plug in camera to computer and download video.

140° degree glass lens

Microphone

Dual track mounting system

Mini USB

connector

SD Card

reformat button

Mini SD Card slot

Getting to Know the XTC-100

Batteries

1. To insert the batteries, push down the battery door latch on the right side of the camera. Door will release. Push forward to remove.

2. Install 2 AAA batteries observing polarity.

3. Return battery door and click into place.

Battery Status Indicator Meaning

Solid Green Indicates full battery life Solid Red Indicates half battery life Blinking Red* Indicates low battery life No Light Batteries are dead

Note: When the red battery LED begins blinking, be prepared to change the batteries because the camera will stop recording at this point.

Micro SD Card

1. Open and fold down the back rubber cover.

2. Insert Micro SD card into slot observing proper direction (shown sideways).

3. Return rubber ap into place.

Recording

1. Move the RECORD switch forward. This turns the camera on.

2. The battery indicator will light from red to green. The SD card indicator will light green. The record indicator will begin ashing red after 8 seconds. This indicates the camera is capturing video.

3. To stop recording, move the RECORD switch back to the off position.

Note: The camera will continue recording for 3 seconds after toggling the switch to the off position.

SD card LED Status Meaning

Green 1 GB or more avai lable Orange 512 MB to1 GB available Red Below 512 MB available or no MicroSD card installed. Flashing Red Cannot read the card Flashing Green Indicates card has been reformatted.

Memory Size Record Time

512 MB 7.5 Minutes 1 GB 15 Minutes 2 GB 30 Minutes 4 GB 60 Minutes 8 GB 120 Minutes 16 GB 240 Minutes 32 GB 480 Minutes

Note: The camera automatically splits the video into 2 GB segments.

Camera Mounting

Mount on Dual Track System

The XTC-100 was innovatively designed with an identical dual track mount system on either side of the camera. This allows an ease of installation. To mount the camera on the dual track mount, slide the camera onto the dual track system with the two notches on the mount facing towards the back of the camera. To detach the camera from the dual track mount, hold the camera with the lens facing away from you. Press down the mount release switch and pull the mount towards yourself. The dual track mount allows the camera to be easily mounted on both helmet mount and goggle mount. This elimi nates the hassle of having to remount the camera

Helmet adhesive mount Goggle mount

every time.

When mounting the camera on the dual track mount, you must do the following:

1. Consider what you would like to shoot and use the helmet mount or goggle mount accordingly.

2. Ensure, once attached, that the camera is aimed straight and not towards the ground or at the sky.

Mount using the Thread Mount

On the bottom of the XTC-100 is a standard thread mount that allows the camera to be mounted to an helmet strap mount or to a bicycle handlebar mount.

To x the camera, insert the screw on the mount into

Camera thread Mounting screw

the camera thread and rotate the camera clockwise to tighten down onto the screw. When mounting the camera on the handlebars of a bike or with the vented helmet strap mount follow these steps:

1. Consider what you would like to shoot and mount accordingly.

2. Ensure, once attached, that the camera is aimed

Helmet strap mount Bicycle handle bar mount

straight and not towards the ground or at the sky.

Compatible Systems

The XTC-100 can be used on both Windows operating system and MAC. The camera records as AVI.

Downloading Videos

There is no need to install any software with the XTC-100. It is a plug and play device. Ensure batteries are new or fully charged before downloading video.

Connect the camera to the USB port using the included cable. The camera will be automatically recognized as external hard drive (USB key) All your videos will be saved into the DCIM folder.

Reformatting the Micro SD card

dual track system mount

Release button

The Micro SD card can be reformatted while in the camera. This allows you to delete all the videos at one time. Follow these steps:

1. Move the RECORD switch to the record position.

2. When the battery indicator turns green, press and hold the Micro SD card reformat button.

3. Keep the Micro SD card reformat button down until the record indicator turns off and the SD card indicator begins blinking green.

4. Move the RECORD switch to the off position.

Note: The camera cannot reformat the Micro SD card if the low battery light is on. Ensure new batteries are installed in the camera before attempting the reformat process.

Tips and Tricks

Problem Solution

Batteries

Camera not turning on Ensure the batteries are installed properly observing polarity.

Recording

Camera not recording Make sure the switch is pushed all the way forward. If the record LED does not

Micro SD card

Micro SD card not reading Ensure the Micro SD card is inserted properly.

Video Playback

Slow or choppy video Verify the camera is plugged into a USB 2.0 device.

Video Downloading

Slow data transfer Verify the camera is plugged into a USB 2.0 device. If registering as 1.1, unplug and

Computer does notrecognize camera

Sound

Excessive Wind Noise Place piece of tape over microphone hole.

Make sure batteries are new or fully charged.

come on, turn off the device and reinstall the batteries. Verify available memory.

Plug camera into the computer to verify it has available storage. Attempt formatting process.

Remove other unused USB devices. Transfer video to computer before viewing.

the re-plug the device. Remove other unused USB devices. Ensure record switch is in the record position while connected to computer. Ensure the Micro SD card is inserted properly. Micro SD card may becorrupted. Attempt formatting process.

Limited Warranty

Midland Radio Corporation will repair or replace, at its option without charge, any Midland XTC-100 Action camera which fails due to a defect in material or workmanship within TWO Years following the initial consumer purchase. This warranty does not apply to accidents of any kind, exposure to pressure, extreme temperatures (outside of -10°C to 45°C), and submersion water damage as this product is water resistant but not waterproof, battery leak or abuse. Accessories have a 90 day warranty from date of purchase, inclu ding any mounts and cables. This warranty does not include the cost of labor for removal or re-installation of the product in a vehicle or other mounting.

Hereby, CTE International declares that this XTC-100 is in compliance with the essential requirements and other relevant provisions the Electromagnetic Compatibility Directive 2004/108/CE. A copy of Declaration of Conformity can be found at: www.midlandradio.eu

XTC-100 Action Camera

your computer and upload the videos to share with friends. It is that simple! Enjoy!

What’s in the box

XTC-100 Features and Controls

Features:

› 640x480 resolution (4:3 aspect ratio) › Records as AVI › 30 frames per second › 140 degree angle lens

Record switch

forward:

on/record

Record led

ashes red when

camera is recording

Battery led

Record switch

backward: Off/Stop recording

SD Card led

Quick Start Guide

1. Open battery door and install batteries observing polarity. Replace battery cover.

2. Open and fold down back rubber cover. Insert micro Sd card observing proper direction. Close cover.

3. Move RECORD switch forward, recording will start in 8 seconds.

4. To stop recording, slide switch back to the off position.

5. Plug in camera to computer and download video.

140° degree glass lens

Microphone

Dual track mounting system

Mini USB

connector

SD Card

reformat button

Mini SD Card slot

Getting to Know the XTC-100

Batteries

1. To insert the batteries, push down the battery door latch on the right side of the camera. Door will release. Push forward to remove.

2. Install 2 AAA batteries observing polarity.

3. Return battery door and click into place.

Battery Status Indicator Meaning

Solid Green Indicates full battery life Solid Red Indicates half battery life Blinking Red* Indicates low battery life No Light Batteries are dead

Note: When the red battery LED begins blinking, be prepared to change the batteries because the camera will stop recording at this point.

Micro SD Card

1. Open and fold down the back rubber cover.

2. Insert Micro SD card into slot observing proper direction (shown sideways).

3. Return rubber ap into place.

Recording

1. Move the RECORD switch forward. This turns the camera on.

3. To stop recording, move the RECORD switch back to the off position.

Note: The camera will continue recording for 3 seconds after toggling the switch to the off position.

SD card LED Status Meaning

Memory Size Record Time

512 MB 7.5 Minutes 1 GB 15 Minutes 2 GB 30 Minutes 4 GB 60 Minutes 8 GB 120 Minutes 16 GB 240 Minutes 32 GB 480 Minutes

Note: The camera automatically splits the video into 2 GB segments.

Camera Mounting

Mount on Dual Track System

Helmet adhesive mount Goggle mount

every time.

When mounting the camera on the dual track mount, you must do the following:

1. Consider what you would like to shoot and use the helmet mount or goggle mount accordingly.

2. Ensure, once attached, that the camera is aimed straight and not towards the ground or at the sky.

Mount using the Thread Mount

On the bottom of the XTC-100 is a standard thread mount that allows the camera to be mounted to an helmet strap mount or to a bicycle handlebar mount.

To x the camera, insert the screw on the mount into

Camera thread Mounting screw

the camera thread and rotate the camera clockwise to tighten down onto the screw. When mounting the camera on the handlebars of a bike or with the vented helmet strap mount follow these steps:

1. Consider what you would like to shoot and mount accordingly.

2. Ensure, once attached, that the camera is aimed

Helmet strap mount Bicycle handle bar mount

straight and not towards the ground or at the sky.

Compatible Systems

The XTC-100 can be used on both Windows operating system and MAC. The camera records as AVI.

Downloading Videos

There is no need to install any software with the XTC-100. It is a plug and play device. Ensure batteries are new or fully charged before downloading video.

Connect the camera to the USB port using the included cable. The camera will be automatically recognized as external hard drive (USB key) All your videos will be saved into the DCIM folder.

Reformatting the Micro SD card

dual track system mount

Release button

The Micro SD card can be reformatted while in the camera. This allows you to delete all the videos at one time. Follow these steps:

1. Move the RECORD switch to the record position.

2. When the battery indicator turns green, press and hold the Micro SD card reformat button.

3. Keep the Micro SD card reformat button down until the record indicator turns off and the SD card indicator begins blinking green.

4. Move the RECORD switch to the off position.

Note: The camera cannot reformat the Micro SD card if the low battery light is on. Ensure new batteries are installed in the camera before attempting the reformat process.

Tips and Tricks

Problem Solution

Batteries

Camera not turning on Ensure the batteries are installed properly observing polarity.

Recording

Camera not recording Make sure the switch is pushed all the way forward. If the record LED does not

Micro SD card

Micro SD card not reading Ensure the Micro SD card is inserted properly.

Video Playback

Slow or choppy video Verify the camera is plugged into a USB 2.0 device.

Video Downloading

Slow data transfer Verify the camera is plugged into a USB 2.0 device. If registering as 1.1, unplug and

Computer does notrecognize camera

Sound

Excessive Wind Noise Place piece of tape over microphone hole.

Make sure batteries are new or fully charged.

come on, turn off the device and reinstall the batteries. Verify available memory.

Plug camera into the computer to verify it has available storage. Attempt formatting process.

Remove other unused USB devices. Transfer video to computer before viewing.

Limited Warranty

XTC-100 Action Camera

your computer and upload the videos to share with friends. It is that simple! Enjoy!

What’s in the box

XTC-100 Features and Controls

Features:

› 640x480 resolution (4:3 aspect ratio) › Records as AVI › 30 frames per second › 140 degree angle lens

Record switch

forward:

on/record

Record led

ashes red when

camera is recording

Battery led

Record switch

backward: Off/Stop recording

SD Card led

Quick Start Guide

1. Open battery door and install batteries observing polarity. Replace battery cover.

2. Open and fold down back rubber cover. Insert micro Sd card observing proper direction. Close cover.

3. Move RECORD switch forward, recording will start in 8 seconds.

4. To stop recording, slide switch back to the off position.

5. Plug in camera to computer and download video.

140° degree glass lens

Microphone

Dual track mounting system

Mini USB

connector

SD Card

reformat button

Mini SD Card slot

Getting to Know the XTC-100

Batteries

1. To insert the batteries, push down the battery door latch on the right side of the camera. Door will release. Push forward to remove.

2. Install 2 AAA batteries observing polarity.

3. Return battery door and click into place.

Battery Status Indicator Meaning

Solid Green Indicates full battery life Solid Red Indicates half battery life Blinking Red* Indicates low battery life No Light Batteries are dead

Note: When the red battery LED begins blinking, be prepared to change the batteries because the camera will stop recording at this point.

Micro SD Card

1. Open and fold down the back rubber cover.

2. Insert Micro SD card into slot observing proper direction (shown sideways).

3. Return rubber ap into place.

Recording

1. Move the RECORD switch forward. This turns the camera on.

3. To stop recording, move the RECORD switch back to the off position.

Note: The camera will continue recording for 3 seconds after toggling the switch to the off position.

SD card LED Status Meaning

Memory Size Record Time

512 MB 7.5 Minutes 1 GB 15 Minutes 2 GB 30 Minutes 4 GB 60 Minutes 8 GB 120 Minutes 16 GB 240 Minutes 32 GB 480 Minutes

Note: The camera automatically splits the video into 2 GB segments.

Camera Mounting

Mount on Dual Track System

Helmet adhesive mount Goggle mount

every time.

When mounting the camera on the dual track mount, you must do the following:

1. Consider what you would like to shoot and use the helmet mount or goggle mount accordingly.

2. Ensure, once attached, that the camera is aimed straight and not towards the ground or at the sky.

Mount using the Thread Mount

On the bottom of the XTC-100 is a standard thread mount that allows the camera to be mounted to an helmet strap mount or to a bicycle handlebar mount.

To x the camera, insert the screw on the mount into

Camera thread Mounting screw

the camera thread and rotate the camera clockwise to tighten down onto the screw. When mounting the camera on the handlebars of a bike or with the vented helmet strap mount follow these steps:

1. Consider what you would like to shoot and mount accordingly.

2. Ensure, once attached, that the camera is aimed

Helmet strap mount Bicycle handle bar mount

straight and not towards the ground or at the sky.

Compatible Systems

The XTC-100 can be used on both Windows operating system and MAC. The camera records as AVI.

Downloading Videos

There is no need to install any software with the XTC-100. It is a plug and play device. Ensure batteries are new or fully charged before downloading video.

Connect the camera to the USB port using the included cable. The camera will be automatically recognized as external hard drive (USB key) All your videos will be saved into the DCIM folder.

Reformatting the Micro SD card

dual track system mount

Release button

The Micro SD card can be reformatted while in the camera. This allows you to delete all the videos at one time. Follow these steps:

1. Move the RECORD switch to the record position.

2. When the battery indicator turns green, press and hold the Micro SD card reformat button.

3. Keep the Micro SD card reformat button down until the record indicator turns off and the SD card indicator begins blinking green.

4. Move the RECORD switch to the off position.

Note: The camera cannot reformat the Micro SD card if the low battery light is on. Ensure new batteries are installed in the camera before attempting the reformat process.

Tips and Tricks

Problem Solution

Batteries

Camera not turning on Ensure the batteries are installed properly observing polarity.

Recording

Camera not recording Make sure the switch is pushed all the way forward. If the record LED does not

Micro SD card

Micro SD card not reading Ensure the Micro SD card is inserted properly.

Video Playback

Slow or choppy video Verify the camera is plugged into a USB 2.0 device.

Video Downloading

Slow data transfer Verify the camera is plugged into a USB 2.0 device. If registering as 1.1, unplug and

Computer does notrecognize camera

Sound

Excessive Wind Noise Place piece of tape over microphone hole.

Make sure batteries are new or fully charged.

come on, turn off the device and reinstall the batteries. Verify available memory.

Plug camera into the computer to verify it has available storage. Attempt formatting process.

Remove other unused USB devices. Transfer video to computer before viewing.

Limited Warranty

XTC-100 Action Camera

degree algle lens and 2 hour battery life you never miss a minute of the action. Once captured, simply connect to your computer and upload the videos to share with friends. It is that simple! Enjoy!

What’s in the box

XTC-100 Features and Controls

Features:

› 640x480 resolution (4:3 aspect ratio) › Records as AVI › 30 frames per second › 140 degree angle lens

Record switch

forward:

on/record

Record led

ashes red when

camera is recording

Battery led

Record switch

backward: Off/Stop recording

SD Card led

Quick Start Guide

1. Open battery door and install batteries observing polarity. Replace battery cover.

2. Open and fold down back rubber cover. Insert micro Sd card observing proper direction. Close cover.

3. Move RECORD switch forward, recording will start in 8 seconds.

4. To stop recording, slide switch back to the off position.

5. Plug in camera to computer and download video.

140° degree glass lens

Microphone

Dual track mounting system

Mini USB

connector

SD Card

reformat button

Mini SD Card slot

Getting to Know the XTC-100

Batteries

1. To insert the batteries, push down the battery door latch on the right side of the camera. Door will release. Push forward to remove.

2. Install 2 AAA batteries observing polarity.

3. Return battery door and click into place.

Battery Status Indicator Meaning

Solid Green Indicates full battery life Solid Red Indicates half battery life Blinking Red* Indicates low battery life No Light Batteries are dead

Note: When the red battery LED begins blinking, be prepared to change the batteries because the camera will stop recording at this point.

Micro SD Card

1. Open and fold down the back rubber cover.

2. Insert Micro SD card into slot observing proper direction (shown sideways).

3. Return rubber ap into place.

Recording

1. Move the RECORD switch forward. This turns the camera on.

3. To stop recording, move the RECORD switch back to the off position.

Note: The camera will continue recording for 3 seconds after toggling the switch to the off position.

SD card LED Status Meaning

Memory Size Record Time

512 MB 7.5 Minutes 1 GB 15 Minutes 2 GB 30 Minutes 4 GB 60 Minutes 8 GB 120 Minutes 16 GB 240 Minutes 32 GB 480 Minutes

Note: The camera automatically splits the video into 2 GB segments.

Camera Mounting

Mount on Dual Track System

Helmet adhesive mount Goggle mount

every time.

When mounting the camera on the dual track mount, you must do the following:

1. Consider what you would like to shoot and use the helmet mount or goggle mount accordingly.

2. Ensure, once attached, that the camera is aimed straight and not towards the ground or at the sky.

Mount using the Thread Mount

On the bottom of the XTC-100 is a standard thread mount that allows the camera to be mounted to an helmet strap mount or to a bicycle handlebar mount.

To x the camera, insert the screw on the mount into

Camera thread Mounting screw

the camera thread and rotate the camera clockwise to tighten down onto the screw. When mounting the camera on the handlebars of a bike or with the vented helmet strap mount follow these steps:

1. Consider what you would like to shoot and mount accordingly.

2. Ensure, once attached, that the camera is aimed

Helmet strap mount Bicycle handle bar mount

straight and not towards the ground or at the sky.

Compatible Systems

The XTC-100 can be used on both Windows operating system and MAC. The camera records as AVI.

Downloading Videos

There is no need to install any software with the XTC-100. It is a plug and play device. Ensure batteries are new or fully charged before downloading video.

Connect the camera to the USB port using the included cable. The camera will be automatically recognized as external hard drive (USB key) All your videos will be saved into the DCIM folder.

Reformatting the Micro SD card

dual track system mount

Release button

The Micro SD card can be reformatted while in the camera. This allows you to delete all the videos at one time. Follow these steps:

1. Move the RECORD switch to the record position.

2. When the battery indicator turns green, press and hold the Micro SD card reformat button.

3. Keep the Micro SD card reformat button down until the record indicator turns off and the SD card indicator begins blinking green.

4. Move the RECORD switch to the off position.

Note: The camera cannot reformat the Micro SD card if the low battery light is on. Ensure new batteries are installed in the camera before attempting the reformat process.

Tips and Tricks

Problem Solution

Batteries

Camera not turning on Ensure the batteries are installed properly observing polarity.

Recording

Camera not recording Make sure the switch is pushed all the way forward. If the record LED does not

Micro SD card

Micro SD card not reading Ensure the Micro SD card is inserted properly.

Video Playback

Slow or choppy video Verify the camera is plugged into a USB 2.0 device.

Video Downloading

Slow data transfer Verify the camera is plugged into a USB 2.0 device. If registering as 1.1, unplug and

Computer does notrecognize camera

Sound

Excessive Wind Noise Place piece of tape over microphone hole.

Make sure batteries are new or fully charged.

come on, turn off the device and reinstall the batteries. Verify available memory.

Plug camera into the computer to verify it has available storage. Attempt formatting process.

Remove other unused USB devices. Transfer video to computer before viewing.

Limited Warranty

XTC-100 Action Camera

your computer and upload the videos to share with friends. It is that simple! Enjoy!

What’s in the box

XTC-100 Features and Controls

Features:

› 640x480 resolution (4:3 aspect ratio) › Records as AVI › 30 frames per second › 140 degree angle lens

Record switch

forward:

on/record

Record led

ashes red when

camera is recording

Battery led

Record switch

backward: Off/Stop recording

SD Card led

Quick Start Guide

1. Open battery door and install batteries observing polarity. Replace battery cover.

2. Open and fold down back rubber cover. Insert micro Sd card observing proper direction. Close cover.

3. Move RECORD switch forward, recording will start in 8 seconds.

4. To stop recording, slide switch back to the off position.

5. Plug in camera to computer and download video.

140° degree glass lens

Microphone

Dual track mounting system

Mini USB

connector

SD Card

reformat button

Mini SD Card slot

Getting to Know the XTC-100

Batteries

1. To insert the batteries, push down the battery door latch on the right side of the camera. Door will release. Push forward to remove.

2. Install 2 AAA batteries observing polarity.

3. Return battery door and click into place.

Battery Status Indicator Meaning

Solid Green Indicates full battery life Solid Red Indicates half battery life Blinking Red* Indicates low battery life No Light Batteries are dead

Note: When the red battery LED begins blinking, be prepared to change the batteries because the camera will stop recording at this point.

Micro SD Card

1. Open and fold down the back rubber cover.

2. Insert Micro SD card into slot observing proper direction (shown sideways).

3. Return rubber ap into place.

Recording

1. Move the RECORD switch forward. This turns the camera on.

3. To stop recording, move the RECORD switch back to the off position.

Note: The camera will continue recording for 3 seconds after toggling the switch to the off position.

SD card LED Status Meaning

Memory Size Record Time

512 MB 7.5 Minutes 1 GB 15 Minutes 2 GB 30 Minutes 4 GB 60 Minutes 8 GB 120 Minutes 16 GB 240 Minutes 32 GB 480 Minutes

Note: The camera automatically splits the video into 2 GB segments.

Camera Mounting

Mount on Dual Track System

Helmet adhesive mount Goggle mount

When mounting the camera on the dual track mount, you must do the following:

1. Consider what you would like to shoot and use the helmet mount or goggle mount accordingly.

2. Ensure, once attached, that the camera is aimed straight and not towards the ground or at the sky.

Mount using the Thread Mount

On the bottom of the XTC-100 is a standard thread mount that allows the camera to be mounted to an helmet strap mount or to a bicycle handlebar mount.

To x the camera, insert the screw on the mount into

Camera thread Mounting screw

the camera thread and rotate the camera clockwise to tighten down onto the screw. When mounting the camera on the handlebars of a bike or with the vented helmet strap mount follow these steps:

1. Consider what you would like to shoot and mount accordingly.

2. Ensure, once attached, that the camera is aimed

Helmet strap mount Bicycle handle bar mount

straight and not towards the ground or at the sky.

Compatible Systems

The XTC-100 can be used on both Windows operating system and MAC. The camera records as AVI.

Downloading Videos

There is no need to install any software with the XTC-100. It is a plug and play device. Ensure batteries are new or fully charged before downloading video.

Connect the camera to the USB port using the included cable. The camera will be automatically recognized as external hard drive (USB key) All your videos will be saved into the DCIM folder.

Reformatting the Micro SD card

dual track system mount

Release button

The Micro SD card can be reformatted while in the camera. This allows you to delete all the videos at one time. Follow these steps:

1. Move the RECORD switch to the record position.

2. When the battery indicator turns green, press and hold the Micro SD card reformat button.

3. Keep the Micro SD card reformat button down until the record indicator turns off and the SD card indicator begins blinking green.

4. Move the RECORD switch to the off position.

Note: The camera cannot reformat the Micro SD card if the low battery light is on. Ensure new batteries are installed in the camera before attempting the reformat process.

Tips and Tricks

Problem Solution

Batteries

Camera not turning on Ensure the batteries are installed properly observing polarity.

Recording

Camera not recording Make sure the switch is pushed all the way forward. If the record LED does not

Micro SD card

Micro SD card not reading Ensure the Micro SD card is inserted properly.

Video Playback

Slow or choppy video Verify the camera is plugged into a USB 2.0 device.

Video Downloading

Slow data transfer Verify the camera is plugged into a USB 2.0 device. If registering as 1.1, unplug and

Computer does notrecognize camera

Sound

Excessive Wind Noise Place piece of tape over microphone hole.

Make sure batteries are new or fully charged.

come on, turn off the device and reinstall the batteries. Verify available memory.

Plug camera into the computer to verify it has available storage. Attempt formatting process.

Remove other unused USB devices. Transfer video to computer before viewing.

Limited Warranty

XTC-100 Action Camera

your computer and upload the videos to share with friends. It is that simple! Enjoy!

What’s in the box

XTC-100 Features and Controls

Features:

› 640x480 resolution (4:3 aspect ratio) › Records as AVI › 30 frames per second › 140 degree angle lens

Record switch

forward:

on/record

Record led

ashes red when

camera is recording

Battery led

Record switch

backward: Off/Stop recording

SD Card led

Quick Start Guide

1. Open battery door and install batteries observing polarity. Replace battery cover.

2. Open and fold down back rubber cover. Insert micro Sd card observing proper direction. Close cover.

3. Move RECORD switch forward, recording will start in 8 seconds.

4. To stop recording, slide switch back to the off position.

5. Plug in camera to computer and download video.

140° degree glass lens

Microphone

Dual track mounting system

Mini USB

connector

SD Card

reformat button

Mini SD Card slot

Getting to Know the XTC-100

Batteries

1. To insert the batteries, push down the battery door latch on the right side of the camera. Door will release. Push forward to remove.

2. Install 2 AAA batteries observing polarity.

3. Return battery door and click into place.

Battery Status Indicator Meaning

Solid Green Indicates full battery life Solid Red Indicates half battery life Blinking Red* Indicates low battery life No Light Batteries are dead

Note: When the red battery LED begins blinking, be prepared to change the batteries because the camera will stop recording at this point.

Micro SD Card

1. Open and fold down the back rubber cover.

2. Insert Micro SD card into slot observing proper direction (shown sideways).

3. Return rubber ap into place.

Recording

1. Move the RECORD switch forward. This turns the camera on.

3. To stop recording, move the RECORD switch back to the off position.

Note: The camera will continue recording for 3 seconds after toggling the switch to the off position.

SD card LED Status Meaning

Memory Size Record Time

512 MB 7.5 Minutes 1 GB 15 Minutes 2 GB 30 Minutes 4 GB 60 Minutes 8 GB 120 Minutes 16 GB 240 Minutes 32 GB 480 Minutes

Note: The camera automatically splits the video into 2 GB segments.

Camera Mounting

Mount on Dual Track System

Helmet adhesive mount Goggle mount

every time.

When mounting the camera on the dual track mount, you must do the following:

1. Consider what you would like to shoot and use the helmet mount or goggle mount accordingly.

2. Ensure, once attached, that the camera is aimed straight and not towards the ground or at the sky.

Mount using the Thread Mount

On the bottom of the XTC-100 is a standard thread mount that allows the camera to be mounted to an helmet strap mount or to a bicycle handlebar mount.

To x the camera, insert the screw on the mount into

Camera thread Mounting screw

the camera thread and rotate the camera clockwise to tighten down onto the screw. When mounting the camera on the handlebars of a bike or with the vented helmet strap mount follow these steps:

1. Consider what you would like to shoot and mount accordingly.

2. Ensure, once attached, that the camera is aimed

Helmet strap mount Bicycle handle bar mount

straight and not towards the ground or at the sky.

Compatible Systems

The XTC-100 can be used on both Windows operating system and MAC. The camera records as AVI.

Downloading Videos

There is no need to install any software with the XTC-100. It is a plug and play device. Ensure batteries are new or fully charged before downloading video.

Connect the camera to the USB port using the included cable. The camera will be automatically recognized as external hard drive (USB key) All your videos will be saved into the DCIM folder.

Reformatting the Micro SD card

dual track system mount

Release button

The Micro SD card can be reformatted while in the camera. This allows you to delete all the videos at one time. Follow these steps:

1. Move the RECORD switch to the record position.

2. When the battery indicator turns green, press and hold the Micro SD card reformat button.

3. Keep the Micro SD card reformat button down until the record indicator turns off and the SD card indicator begins blinking green.

4. Move the RECORD switch to the off position.

Note: The camera cannot reformat the Micro SD card if the low battery light is on. Ensure new batteries are installed in the camera before attempting the reformat process.

Tips and Tricks

Problem Solution

Batteries

Camera not turning on Ensure the batteries are installed properly observing polarity.

Recording

Camera not recording Make sure the switch is pushed all the way forward. If the record LED does not

Micro SD card

Micro SD card not reading Ensure the Micro SD card is inserted properly.

Video Playback

Slow or choppy video Verify the camera is plugged into a USB 2.0 device.

Video Downloading

Slow data transfer Verify the camera is plugged into a USB 2.0 device. If registering as 1.1, unplug and

Computer does notrecognize camera

Sound

Excessive Wind Noise Place piece of tape over microphone hole.

Make sure batteries are new or fully charged.

come on, turn off the device and reinstall the batteries. Verify available memory.

Plug camera into the computer to verify it has available storage. Attempt formatting process.

Remove other unused USB devices. Transfer video to computer before viewing.

Limited Warranty

XTC-100 Action Camera

your computer and upload the videos to share with friends. It is that simple! Enjoy!

What’s in the box

XTC-100 Features and Controls

Features:

› 640x480 resolution (4:3 aspect ratio) › Records as AVI › 30 frames per second › 140 degree angle lens

Record switch

forward:

on/record

Record led

ashes red when

camera is recording

Battery led

Record switch

backward: Off/Stop recording

SD Card led

Quick Start Guide

1. Open battery door and install batteries observing polarity. Replace battery cover.

2. Open and fold down back rubber cover. Insert micro Sd card observing proper direction. Close cover.

3. Move RECORD switch forward, recording will start in 8 seconds.

4. To stop recording, slide switch back to the off position.

5. Plug in camera to computer and download video.

140° degree glass lens

Microphone

Dual track mounting system

Mini USB

connector

SD Card

reformat button

Mini SD Card slot

Getting to Know the XTC-100

Batteries

1. To insert the batteries, push down the battery door latch on the right side of the camera. Door will release. Push forward to remove.

2. Install 2 AAA batteries observing polarity.

3. Return battery door and click into place.

Battery Status Indicator Meaning

Solid Green Indicates full battery life Solid Red Indicates half battery life Blinking Red* Indicates low battery life No Light Batteries are dead

Note: When the red battery LED begins blinking, be prepared to change the batteries because the camera will stop recording at this point.

Micro SD Card

1. Open and fold down the back rubber cover.

2. Insert Micro SD card into slot observing proper direction (shown sideways).

3. Return rubber ap into place.

Recording

1. Move the RECORD switch forward. This turns the camera on.

3. To stop recording, move the RECORD switch back to the off position.

Note: The camera will continue recording for 3 seconds after toggling the switch to the off position.

SD card LED Status Meaning

Memory Size Record Time

512 MB 7.5 Minutes 1 GB 15 Minutes 2 GB 30 Minutes 4 GB 60 Minutes 8 GB 120 Minutes 16 GB 240 Minutes 32 GB 480 Minutes

Note: The camera automatically splits the video into 2 GB segments.

Camera Mounting

Mount on Dual Track System

Helmet adhesive mount Goggle mount

every time.

When mounting the camera on the dual track mount, you must do the following:

1. Consider what you would like to shoot and use the helmet mount or goggle mount accordingly.

2. Ensure, once attached, that the camera is aimed straight and not towards the ground or at the sky.

Mount using the Thread Mount

On the bottom of the XTC-100 is a standard thread mount that allows the camera to be mounted to an helmet strap mount or to a bicycle handlebar mount.

To x the camera, insert the screw on the mount into

Camera thread Mounting screw

the camera thread and rotate the camera clockwise to tighten down onto the screw. When mounting the camera on the handlebars of a bike or with the vented helmet strap mount follow these steps:

1. Consider what you would like to shoot and mount accordingly.

2. Ensure, once attached, that the camera is aimed

Helmet strap mount Bicycle handle bar mount

straight and not towards the ground or at the sky.

Compatible Systems

The XTC-100 can be used on both Windows operating system and MAC. The camera records as AVI.

Downloading Videos

There is no need to install any software with the XTC-100. It is a plug and play device. Ensure batteries are new or fully charged before downloading video.

Connect the camera to the USB port using the included cable. The camera will be automatically recognized as external hard drive (USB key) All your videos will be saved into the DCIM folder.

Reformatting the Micro SD card

dual track system mount

Release button

The Micro SD card can be reformatted while in the camera. This allows you to delete all the videos at one time. Follow these steps:

1. Move the RECORD switch to the record position.

2. When the battery indicator turns green, press and hold the Micro SD card reformat button.

3. Keep the Micro SD card reformat button down until the record indicator turns off and the SD card indicator begins blinking green.

4. Move the RECORD switch to the off position.

Note: The camera cannot reformat the Micro SD card if the low battery light is on. Ensure new batteries are installed in the camera before attempting the reformat process.

Tips and Tricks

Problem Solution

Batteries

Camera not turning on Ensure the batteries are installed properly observing polarity.

Recording

Camera not recording Make sure the switch is pushed all the way forward. If the record LED does not

Micro SD card

Micro SD card not reading Ensure the Micro SD card is inserted properly.

Video Playback

Slow or choppy video Verify the camera is plugged into a USB 2.0 device.

Video Downloading

Slow data transfer Verify the camera is plugged into a USB 2.0 device. If registering as 1.1, unplug and

Computer does notrecognize camera

Sound

Excessive Wind Noise Place piece of tape over microphone hole.

Make sure batteries are new or fully charged.

come on, turn off the device and reinstall the batteries. Verify available memory.

Plug camera into the computer to verify it has available storage. Attempt formatting process.

Remove other unused USB devices. Transfer video to computer before viewing.

Limited Warranty

XTC-100 Action Camera

Благодарим Вас за приобретение видеокамеры XTC-100, которая позволит любителям острых ощущений делать видеозаписи своих приключений. Простота в использовании, широкий угол обзора, 2 часа в режиме записи гарантируют то, что вы не пропустите ни одной секунды, наполненной адреналином.

Сделав запись, подключите камеру к компьютеру, загрузите видеоролик в Интернет и разделите свои эмоции с друзьями!

Комплектация:

› видеокамера XTC-100 Action Camera › карта памяти SD (емкость 2 Гб) › 2 щелочные батарейки типа ААА › кабель USB › крепеж на очки › крепеж на шлем на липучке › крепеж на шлем на ремешке › крепеж на руль велосипеда/мотоцикла › держатель для установки видеокамеры на шлем или очки

Характеристики видеокамеры и элементы управления

Характеристики:

› разрешение 640х480 (размер кадра 4:3) › формат записи: AVI (30 кадров в секунду) › угол обзора 140°

ползунок записи (Rec)

в верхней позиции –

включение камеры/

запись ролика

индикатор записи (Rec)

– мигает красным светом

во время записи ролика

индикатор батареи

ползунок записи (Rec)

в нижней позиции – остановка записи/ выключение камеры

индикатор карты памяти

Краткое руководство по использованию видеокамеры

1. Откройте крышку батарейного отсека и установите батарейки, соблюдая полярность.

Закройте крышку батарейного отсека.

2. Откройте резиновую крышку отсека карты памяти и установите карту памяти.

Закройте крышку отсека карты памяти.

3. Установите ползунок записи (Rec) в верхней позиции – запись начнется через 8 секунд.

4. Для остановки записи переместите ползунок (Rec) в нижнюю позицию (off).

5. Подключите камеру к персональному компьютеру и скопируйте видеоролик.

угол обзора 140°

микрофон

направляющие крепления камеры на держателе

Mini USB разъем

кнопка форматирования

карты памяти

отсек Mini SD

карты памяти

Установка батареек

1. Отсек для батареек расположен с правой стороны камеры. Нажмите на фиксатор батарейного отсека и сдвиньте крышку в сторону объектива – теперь можно ее снять.

2. Установите 2 батарейки типа ААА, соблюдая полярность.

3. Установите крышку батарейного отсека (при правильной установке,

вы услышите щелчок).

Индикация уровня разряда батареек

Индикатор разряда батареи Соответствующее значение

Постоянно горит зеленым светом Полный заряд батареи Постоянно горит красным светом Батарея наполовину разряжена Мигает красным светом* Низкий уровень заряда батареи Не горит Батарея разряжена

*Внимание: когда индикатор начинает мигать красным светом, камера прекращает запись ролика. В этот момент необходимо произвести замену батареек.

Установка Micro SD карты памяти

1. Откройте отсек карты памяти, расположенный на задней поверхности видеокамеры.

2. Установите карту памяти.

3. Закройте крышку отсека.

Запись ролика

1. Для включения видеокамеры переместите ползунок записи (Rec) ближе к объективу до щелчка.

2. Индикатор разряда батареи загорится зеленым или красным светом. Через 8 секунд индикатор записи (Rec)

начнет мигать красным светом – осуществляется запись ролика.

3. Для остановки записи переместите ползунок (Rec) ближе к USB разъему и разъему для установки Micro SD карты:

камера остановит запись через 3 секунды.

Индикатор состояния Micro SD карты Свободный объем памяти

Горит зеленым светом ≥ 1Гб Горит оранжевым светом 512 Мб – 1Гб Горит красным светом < 512 Мб или карта не установлена Мигает красным светом Карта не читается Мигает зеленым светом Карта была отформатирована

Объем памяти Доступное время записи (в мин.)

512 Мб 7,5 1 Гб 15 2 Гб 30 4 Гб 60 8 Гб 120 16 Гб 240 32 Гб 480

Внимание: видеокамера автоматически разделяет запись на фрагменты размером 2 Гб.

Установка видеокамеры

В комплекте вы найдете следующие варианты крепежей видеокамеры, характеризующиеся различным назначением и вариантами соединения с видеокамерой:

1. 2 крепежа на шлем:

на липучке – соединение с камерой осуществляется посредством держателя (см. следующий раздел), на ремешке – винтовая система соединения с камерой;

2. крепеж на очки – соединение с камерой

осуществляется посредством держателя (см. следующий раздел);

3. крепеж на руль мотоцикла / велосипеда – винтовая

система соединения с камерой.

Держатель для установки видеокамеры

крепеж на шлем (на липучке) крепеж на очки

на шлем или очки

Данный держатель предназначен для фиксации видеокамеры на крепеже шлема или очков, позволяет быстро и просто сменить положение видеокамеры (шлем-очки) в зависимости от цели / объекта съемки. Для установки видеокамеры на держателе вставьте направляющие выступы видеокамеры в соответствующие бороздки держателя и плавно двигайте камеру вдоль бороздок. Теперь достаточно зафиксировать держатель с камерой на крепеже шлема (на липучке) или очков в необходимой позиции (направлении), учитывая объект предстоящей съемки, и удостовериться, что объектив видеокамеры направлен строго вперед, а не на землю или небо. Камера готова к использованию! Для отсоединения видеокамеры от крепежа, зафиксируйте видеокамеру в руке (объектив направлен от вас), нажмите на рычажок (см. рисунок сверху) и тяните держатель на себя.

Винтовая система соединения камеры с крепежом

Крепеж на шлем (на ремешке) и рулевой крепеж имеют винтовую систему соединения видеокамеры с крепежом. Для фиксации видеокамеры на данном крепеже вставьте винт крепежа в резьбовое соединение видеокамеры,

резьбовое соединение

расположенное на нижней поверхности ее корпуса, и вращайте видеокамеру по часовой стрелке. Установите видеокамеру в необходимом направлении, учитывая объект предстоящей съемки, и удостоверьтесь, что объектив видеокамеры направлен строго вперед, а не на землю или небо. Камера готова к использованию!

крепеж на шлем (на ремешке) крепеж на руль

бороздки держателя

рычажок

винт крепежа

Совместимость видеокамеры с операционными системами персонального компьютера

Видеокамера совместима с операционной системой Windows и MAC. Видеозаписи сохраняются в формате AVI.

Загрузка видеозаписей на персональный компьютер

Для загрузки видеоролика на персональный компьютер (ПК) установка какой-либо программы не требуется. Перед началом загрузки удостоверьтесь, что батареи видеокамеры полностью заряжены. Подключите видеокамеру к персональному компьютеру через разъем USB посредством кабеля, поставляемого в комплекте. Персональный компьютер автоматически распознает внешнее USB устройство.

Все видеоролики сохраняются в папке DCIM.

Форматирование Micro SD карты памяти

Форматируя Micro SD карту памяти, вы можете просто и быстро удалить все видеозаписи. Для этого:

1. Переместите ползунок записи (Rec) в верхнюю позицию (позиция записи).

2. Когда индикатор батареи загорится зеленым светом, нажмите и удерживайте кнопку форматирования карты

памяти.

3. Когда процесс форматирования карты завершится, индикатор записи (Rec) погаснет, а индикатор карты

памяти начнет мигать зеленым светом.

4. Переместите ползунок записи в нижнюю позицию (off).

Внимание: в случае, если горит индикатор низкого заряда батареи, невозможно осуществить форматирование карты памяти. Таким образом, перед началом форматирования удостоверьтесь, что батареи видеокамеры полностью заряжены.

Проблемы и неполадки

Проблема Решение

Батарейки

Камера не включается Проверьте, правильно ли установлены батарейки (соблюдена ли полярность).

Запись

Камера не осуществляет запись Удостоверьтесь, что ползунок записи расположен в верхней позиции

Карта памяти Micro SD

Карта памяти не читается Удостоверьтесь, что карта памяти установлена должным образом.

Просмотр записи

Медленное или прерывистое воспроизведение видео файла

Загрузка видео файла на ПК

Медленная передача данных Удостоверьтесь, что камера подключена к устройству, поддерживающему

Персональный компьютер не распознает камеру, как внешнее USB устройство

Звук

Чрезмерный шум, задувание ветра

Удостоверьтесь, что батарейки полностью заряжены.

(до щелчка). Если индикатор записи не загорается, то выключите камеру и переустановите батарейки.

Проверьте объем доступной памяти.

Посредством ПК проверьте доступный объем памяти. Отформатируйте карту памяти.

Удостоверьтесь, что камера подключена к устройству, поддерживающему

USB 2.0.

Отсоедините другие USB устройства от ПК. Перед просмотром записи сохраните её на ПК.

USB 2.0. Если камера регистрируется как устройство USB 1.1, то отсоедините камеру и снова подключите к ПК.

Отсоедините другие USB устройства от ПК. Удостоверьтесь, что ползунок записи видеокамеры расположен в верхней

позиции (позиция записи). Удостоверьтесь, что карта памяти установлена должным образом. Отформатируйте карту памяти.

Прикройте отверстие микрофона.

Правила эксплуатации и ухода.

! Не пользуйтесь содержащими алкоголь жидкостями и чистящими средствами для очистки видеокамеры. ! Не погружайте видеокамеру в воду. ! Протирайте видеокамеру мягким влажным кусочком ткани. ! На время длительного хранения выключите видеокамеру и удалите из нее батарейки.

Внимание! Не вскрывайте корпус видеокамеры самостоятельно! Несанкционированное вскрытие изделия лишит вас гарантии на устройство!

Гарантия

На данный товар гарантия выдается сроком на один год, считая со дня приобретения товара. Гарантийное обслуживание осуществляется только при условии строгого соблюдения правил эксплуатации и требований безопасности, указанных в руководстве пользователя.

Произведено или импортировано: СТЕ Интернешнл с.р.л. Ул. Р. Севарди 7- 42010 Манкасаль, Реджио Эмилия, Италия

Импортер в России: ЗАО «Алан-Связь» Интернет-сайт: www.midland.ru 105187, г. Москва, Фортунатовская, 31А, стр. 2

MIDLAND XTC-100 User Manual [ru, it, en]

Specifications and Main Features

Frequently Asked Questions

User Manual